uniMac HT075N Industrial Tumble Dryer Maintenance Manual

Huebsch
18 Digit Model Numbers with 6 in 13th Position
Refer to Page 9 for Model Identification
Operation/Maintenance
Tumble Dryers
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com
Part No. 70693401ENR5
August 2024
Installation must conform with local codes or, in the absence of
local codes, with:
WARNING
In the U.S.A., installation must conform to the latest edition of
the American National Standard Z223.1/ NFPA 54 “National
Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric
Code.”
•
In Canada, installation must comply with Standards CAN/CSAB149.1 Natural Gas and Propane Installation Code and CSA
C22.1, latest edition, Canadian Electric Code, Part I.
•
In Australia and New Zealand, installation must comply with the
Gas Installations Standard AS/NZS 5601 Part 1: General Installations.
In Europe, before installation, check that the local distribution
conditions, nature of gas and pressure, and the adjustment of the
appliance are compatible.
This equipment has been designed and certified to comply with
IEC/EN 60335 electrical safety standards for tumble dryers.
•
Read all instructions before using tumble dryer.
W052
IMPORTANT: If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer,
they should first be washed in hot water with extra detergent. This will reduce, but not eliminate, the hazard.
IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the
user smells gas. These instructions must be posted in
a prominent location. Step-by-step instructions of the
above safety information must be posted in a prominent location near the tumble dryer for customer use.
WARNING
IMPORTANT: Post the following statement in a prominent location
FOR YOUR SAFETY
FOR YOUR SAFETY, the information in this manual
must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
W033
IMPORTANT: The installer must fully test the tumble
dryer after installation and demonstrate to the owner
how to operate the machine.
DANGER
Electric shock hazard will result in death or serious
injury. Disconnect all electric power to appliance and
accessories and wait five (5) minutes before servicing.
IMPORTANT: The machine shall only be installed in a
room separated from inhabited rooms, incorporating
appropriate ventilation specified in the National Installation Regulations.
W925
IMPORTANT: The tumble dryer is not to be used if industrial chemicals have been used for cleaning.
Units are IPx4 when enclosed per these instructions.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Clear the room, building or area of all occupants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
3
Part No. 70693401ENR5
CAUTION
WARNING
To reduce the risk of electric shock, fire, explosion,
serious injury or death:
• Disconnect electric power to the tumble dryer before servicing.
• Close gas shut-off valve to gas tumble dryer before servicing.
• Close steam valve to steam tumble dryer before
servicing.
• Never start the tumble dryer with any guards/
panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be reconnected to
ensure that the tumble dryer is properly grounded.
Electrical shock hazard can cause death or serious
injury. To reduce the risk of electric shock, disconnect all electric power to appliance and accessories
before servicing.
W929
WARNING
Moving parts hazard can cause serious injury. Disconnect electric power to unit before servicing. Unexpected start of machinery will occur if the unit is
equipped with the extended tumble feature.
W937
W002R1
WARNING
WARNING
Lint compartment must be cleaned daily
•
•
•
Installation of unit must be performed by a qualified installer.
Install tumble dryer according to manufacturer’s
instructions and local codes.
DO NOT install a tumble dryer with flexible plastic
venting materials. If flexible metal (foil type) duct
is installed, it must be of a specific type identified
by the appliance manufacturer as suitable for use
with tumble dryer. Refer to section on connecting
exhaust system. Flexible venting materials are
known to collapse, be easily crushed, and trap
lint. These conditions will obstruct tumble dryer
airflow and increase the risk of fire.
To avoid the risk of fire:
•
•
•
•
Use for drying water washed fabrics only.
DO NOT dry articles containing foam rubber, plastic, or similarly textured rubber like materials.
DO NOT put articles soiled with cooking oil in dryer as cooking oil may not be removed during
washing. Due to the remaining oil the fabric may
catch on fire by itself.
DO NOT put articles soiled with flammable liquids
or flammable cleaning solvents in dryer.
W930
CAUTION
W752R1
CAUTION
•
TO AVOID THE RISK OF FIRE THIS DRYER MUST BE
EXHAUSTED OUTDOORS.
W928
•
WARNING
•
Risk of fire, a clothes dryer produces combustible
lint. Exhaust outdoors. Care should be taken to
prevent the accumulation of lint around the exhaust opening and in the surrounding area.
DO NOT reach into the dryer until all moving parts
have stopped.
DO NOT let children play on or in the dryer.
W931
To reduce the risk of serious injury: Avoid contact
with hot surfaces.
W927
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4
Part No. 70693401ENR5
•
WARNING
•
•
In Australia and New Zealand:
•
•
•
•
•
•
•
•
DO NOT modify this appliance.
DO NOT operate this appliance before reading the
instruction booklet.
DO NOT place articles on or against this appliance.
DO NOT store chemicals or flammable materials
or spray aerosols near this appliance.
DO NOT operate with panels, covers or guards removed from this appliance.
DO NOT load materials containing flammable solvents into this appliance.
If repeated ignition reset is required, the dryer
should not be used and a service call booked.
Adequate ventilation shall be provided to avoid
the back flow of gases into the room from any
fuel burning appliances, including open fires.
This appliance must be installed with a 36 inch [91 cm] long
flexible gas connector.
A “T-Handle” type gas shut-off valve must be installed in the
gas supply line to this appliance.
This appliance must not be installed in a bedroom or bathroom.
Risk of fire/flammable material.
W926R1
WARNING
Models with electronic control:
•
•
•
•
•
INGESTION HAZARD: This product contains a
non-replaceable button cell or coin battery.
• Battery Type: CR-2450/VAN, CR-2354/VCN,
CR2032
• Nominal voltage: 3V
DEATH or serious injury can occur if ingested.
A swallowed button cell or coin battery can cause
Internal Chemical Burns in as little as 2 hours.
KEEP new and used batteries OUT OF REACH of
CHILDREN.
Seek immediate medical attention if a battery is
suspected to be swallowed or inserted inside any
part of the body.
W1076
The following information applies to the state of Massachusetts,
USA.
• This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5
Part No. 70693401ENR5
Safety Information
Safety Information
•
Important Safety Instructions (Tumble
Dryer)
•
WARNING
To reduce the risk of fire, electric shock, serious injury or death to persons when using your tumble
dryer, follow these basic precautions.
•
W776R1
Save These Instructions
•
•
•
•
•
•
•
•
•
•
•
Read all instructions before using the tumble dryer.
Install the tumble dryer according to the INSTALLATION instructions. Refer to the EARTHING (grounding) instructions
for the proper earthing (grounding) of the tumble dryer. All
connections for electrical power, earthing (grounding) and gas
supply must comply with local codes and be made by licensed
personnel when required. It is recommended that the machine
be installed by qualified technicians.
Do not install or store the tumble dryer where it will be exposed to water and/or weather. The tumble dryer cannot be
used in a closed room where the air supply is insufficient. If
necessary, ventilation grids must be installed in the doors or
the windows.
This tumble dryer must not be activated without lint screen
filter.
When you perceive a gas odor, immediately shut off the gas
supply and ventilate the room. Do not power on electrical appliances and do not pull electrical switches. Do not use
matches or lighters. Do not use a phone in the building. Warn
the installer, and if so desired, the gas company, as soon as
possible.
To avoid fire and explosion, keep surrounding areas free of
flammable and combustible products. Regularly clean the cylinder and exhaust tube should be cleaned periodically by
competent maintenance personnel. Daily remove debris from
lint screen filter and inside of filter compartment.
Do not use or store flammable materials near this appliance.
Do not place into tumble dryer articles that have been previously cleaned in, washed in, soaked in or spotted with gasoline or machine oils, vegetable or cooking oils, cleaning waxes or chemicals, dry-cleaning solvents, thinner or other flammable or explosive substances as they give off vapors that
could ignite, explode or cause fabric to catch on fire by itself.
Do not spray aerosols in the vicinity of this appliance while it
is in operation.
Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows
filled with foam rubber pads should not be dried in the tumble
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
•
•
•
•
•
•
•
•
6
dryer. Do not use the appliance to dry materials with a low
melting temperature (PVC, rubber, etc.).
Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder
with a damp cloth to remove particles of fiberglass.
Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near
children. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning the use
of the appliance by a person responsible for their safety. This
is a safety rule for all appliances.
Cleaning and user maintenance shall not be made by children
without supervision.
Children less than three years should be kept away unless
continuously supervised.
Models with electronic control: Remove and immediately recycle or dispose of used controls according to local regulations and keep away from children. Do NOT dispose of controls in the trash or incinerate. Do not attempt to remove the
batteries. Even used batteries may cause severe injury or
death. Call a local poison control center for treatment information. Non-rechargeable batteries are not to be recharged.
Do not force discharge, recharge, disassemble, heat above
158⁰F [70⁰C] or incinerate. Doing so may result in injury due
to venting, leakage or explosion resulting in chemical burns.
Do not reach into the tumble dryer if the cylinder is revolving.
Use tumble dryer only for its intended purpose, drying fabrics. Always follow the fabric care instructions supplied by
the textile manufacturer and only use the dryer to dry textiles
that have been washed in water. Only insert spin-dried linen
in the dryer to avoid damage to dryer.
Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Follow all warnings or precautions. To reduce the risk of poisoning or chemical burns,
keep them out of the reach of children at all times (preferably
in a locked cabinet).
Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener
or product.
Remove laundry immediately after tumble dryer stops.
DO NOT operate the tumble dryer if it is smoking, grinding
or has missing or broken parts or removed guards or panels.
DO NOT tamper with the controls or bypass any safety devices.
Tumble dryer will not operate with the loading door open. DO
NOT bypass the door safety switch to permit the tumble dryer
to operate with the door open. The tumble dryer will stop rotating when the door is opened. Do not use the tumble dryer if
it does not stop rotating when the door is opened or starts
tumbling without pressing the START mechanism. Remove
the tumble dryer from use and call for service.
Part No. 70693401ENR5
Safety Information
•
•
•
•
•
•
•
•
•
•
Tumble dryer will not operate with lint panel open. DO NOT
bypass lint panel door safety switch to permit the tumble dryer to operate with the lint panel door open.
Do not alter this tumble dryer from factory construction except as otherwise described in the technical instructions.
Always clean the lint filter daily. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and dirt. The interior of the tumble
dryer and the exhaust duct should be cleaned periodically by
qualified service personnel.
Solvent vapors from dry-cleaning machines create acids when
drawn through the heater of the drying unit. These acids are
corrosive to the tumble dryer as well as the laundry load being
dried. Be sure make-up air is free of solvent vapors.
At the end of each working day, close off all main supplies of
gas, steam and electricity.
NOTE: All appliances are produced according to the
EMC-directive (Electro-Magnetic-Compatibility). They
can be used in restricted surroundings only (comply
minimally with class A requirements). For safety reasons there must be kept the necessary precaution distances with sensitive electrical or electronic device(s).
These machines are not intended for domestic use by
private consumers in the home environment.
Explanation of Safety Instruction
Messages
Precautionary statements (“DANGER,” “WARNING,” and
“CAUTION”), followed by specific instructions, are found in this
manual and on machine decals. These precautions are intended
for the personal safety of the operator, user, servicer, and those
maintaining the machine.
IMPORTANT: For fire suppression equipped tumble
dryers, electricity and water should NOT be turned
off.
Do not repair or replace any part of the tumble dryer, or attempt any servicing unless specifically recommended in the
user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry
out. ALWAYS disconnect and lockout the electrical power to
the tumble dryer before servicing. Disconnect power by shutting off appropriate breaker or fuse.
Activation of the emergency stop switch stops all tumble dryer control circuit functions, but DOES NOT remove all electrical power from tumble dryer.
Exhaust ductwork should be examined and cleaned annually
after installation.
Before the tumble dryer is removed from service or discarded,
remove the door to the drying compartment and the door to
the lint compartment.
Failure to install, maintain, and/or operate this tumble dryer
according to the manufacturer’s instructions may result in
conditions which can produce bodily injury and/or property
damage.
DANGER
Indicates an imminently hazardous situation that, if
not avoided, will cause severe personal injury or
death.
WARNING
Indicates a hazardous situation that, if not avoided,
could cause severe personal injury or death.
CAUTION
Indicates a hazardous situation that, if not avoided,
may cause minor or moderate personal injury or
property damage.
Additional precautionary statements (“IMPORTANT” and
“NOTE”) are followed by specific instructions.
NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Observe and be aware of other labels and precautions that are located on the machine. They are intended to provide instruction for safe use of the machine. Common sense, caution and care must be exercised when installing, maintaining, or operating the
tumble dryer.
IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor
machine damage will occur if the procedure is not followed.
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do not understand.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7
Part No. 70693401ENR5
Table of Contents
Safety Information................................................................................. 6
Important Safety Instructions (Tumble Dryer) ...................................................6
Explanation of Safety Instruction Messages...................................................... 7
Introduction........................................................................................... 9
Machine Identification.................................................................................... 9
Contact Information...................................................................................... 12
Operating Instructions..........................................................................14
Operating Instructions................................................................................... 14
Emergency Stop Button................................................................................. 14
Operating Instructions................................................................................... 14
Reversing Operation......................................................................................15
Control Instructions.......................................................................................16
Dual Digital Control.................................................................................. 16
Galaxy 600 (Vend) ....................................................................................16
Galaxy (OPL) ...........................................................................................17
Galaxy Touch Vend Control .......................................................................18
Ignition Control Operation and Troubleshooting.............................................. 18
Internal Control Failure..............................................................................19
Troubleshooting........................................................................................ 19
Proper Electrode Location.......................................................................... 19
Flame Current Measurement.......................................................................20
Maintenance......................................................................................... 21
Daily........................................................................................................... 21
Monthly....................................................................................................... 21
Yearly.......................................................................................................... 21
ProCapture Maintenance................................................................................22
Fire Suppression System (Optional Equipment) Maintenance Test.....................23
Before You Call for Service................................................................... 26
Removing Tumble Dryer from Service.................................................. 27
Disposal of Unit.................................................................................... 28
© Copyright 2024, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8
Part No. 70693401ENR5
Introduction
Introduction
Machine Identification
Information in this manual is applicable to these machines. Refer
to the serial plate.
30 Series (30 lb / 13 Kg)
HA030E
HG030E
HH030L
HJ030N
HK030N
HT030D
HT030N
HU030L
HA030L
HG030L
HH030N
HK030E
HL030E
HT030E
HU030E
HU030N
HA030N
HG030N
HJ030D
HK030L
HL030L
HT030L
HU030F
HU030R
HG030D
HH030E
HJ030E
T30 Series (30/30 lb / 13/13 Kg)
HAT30E
HGT30E
HHT30L
HJT30N
HKT30N
HTT30D
HTT30N
HUT30L
HAT30L
HGT30L
HHT30N
HKT30E
HLT30E
HTT30E
HUT30E
HUT30N
HAT30N
HGT30N
HJT30D
HKT30L
HLT30L
HTT30L
HUT30F
HUT30R
HGT30D
HHT30E
HJT30E
35 Series (35 lb / 16 Kg)
HA035E
HG035D
HG035N
HJ035D
HK035E
HL035L
HT035M
HU035M
HA035L
HG035E
HH035E
HJ035E
HK035L
HT035D
HT035N
HU035N
HA035M
HG035L
HH035M
HJ035M
HK035N
HT035E
HU035E
HU035R
HA035N
HG035M
HH035N
HJ035N
HL035E
HT035L
HU035F
T45 Series (45/45 lb / 20/20 Kg)
HAT45L
HGT45L
HHT45L
HJT45D
HKT45L
HLT45L
HTT45L
HUT45N
HAT45N
HGT45N
HHT45N
HJT45N
HKT45N
HTT45D
HTT45N
HUT45R
HGT45D
50 Series (50 lb / 25 Kg)
HA050E
HG050D
HG050S
HH050S
HJ050N
HK050N
HT050E
HU050E
HA050L
HG050E
HH050E
HJ050D
HJ050S
HL050E
HT050L
HU050L
HA050N
HG050L
HH050L
HJ050E
HK050E
HL050L
HT050N
HU050N
HA050S
HG050N
HH050N
HJ050L
HK050L
HT050C
HT050S
HU050S
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9
Part No. 70693401ENR5
Introduction
55 Series (55 lb / 24 Kg)
HA055E
HG055D
HH055E
HJ055E
HK055L
HL055S
HT055N
HU055L
HA055L
HG055E
HH055L
HJ055N
HK055N
HT055D
HT055S
HU055N
HA055N
HG055L
HH055N
HJ055S
HL055E
HT055E
HU055E
HU055R
HA055S
HG055N
HJ055D
HK055E
HL055L
HT055L
HU055F
HU055S
75 Series (75 lb / 34 Kg)
HA075E
HG075D
HG075S
HH075S
HJ075N
HK075N
HT075L
HU075F
HA075F
HG075E
HH075E
HJ075D
HJ075R
HK075R
HT075M
HU075L
HA075L
HG075F
HH075F
HJ075E
HJ075S
HT075C
HT075N
HU075M
HA075M
HG075L
HH075L
HJ075F
HK075E
HT075D
HT075R
HU075N
HA075N
HG075M
HH075M
HJ075L
HK075F
HT075E
HT075S
HU075R
HA075R
HG075N
HH075N
HJ075M
HK075L
HT075F
HU075E
HU075S
HA075S
HG075R
HH075R
120 Series (120 lb / 55 Kg)
HA120E
HG120E
HH120E
HJ120E
HK120E
HT120C
HT120N
HU120L
HA120L
HG120L
HH120L
HJ120L
HK120L
HT120E
HT120S
HU120N
HA120N
HG120N
HH120N
HJ120N
HK120N
HT120L
HU120E
HU120S
HA120S
HG120S
HH120S
HJ120S
170 Series (170 lb / 77 Kg)
HA170L
HG170L
HH170L
HJ170L
HK170L
HT170L
HT170S
HU170N
HA170N
HG170N
HH170N
HJ170N
HK170N
HT170N
HU170L
HU170S
HA170S
HG170S
HH170S
HJ170S
HT170C
200 Series (200 lb / 90 Kg)
HA200L
HG200L
HH200L
HJ200L
HK200L
HT200L
HT200S
HU200N
HA200N
HG200N
HH200N
HJ200N
HK200N
HT200N
HU200L
HU200S
HA200S
HG200S
HH200S
HJ200S
HT200C
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10
Part No. 70693401ENR5
Introduction
Heater Digit (Position 6)
C - Steam (CRN)
D - Liquid Petroleum (L.P.) Gas, Japan
E - Electric
F - Reduced Electric (Eco Line)
L - L.P. Gas
M - Medium Electric
N - Natural Gas
R - Reduced Gas, Natural Gas (Eco Line)
S - Steam
Vended Control Suffixes
Control Digit (position 7)
Actuation Digit (position 8)
N - Galaxy 600 Networkable
C - Single Coin Drop
V - Galaxy Touch Control
E - Electronic Coin Drop
W - Galaxy 600 Networked
F - Single Coin Drop + CD Lock and
Key
Example Control Suffix Combination
NC - Galaxy 600 Networkable, Single
Coin Drop
WX - Galaxy 600 Networked, Prep for
Coin
H - Electronic Coin Drop + CD Lock and
Key
L - Prep for Central Pay
P - FOB/APP Pay
X - Prep for Coin
Y - Prep for Card
OPL Control Suffixes
Control Digit (position 7)
Actuation Digit (position 8)
Example Control Suffix Combination
F - Dual Digital Control
N - OPL
FN- Dual Digital Control, OPL
N - Galaxy
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
NN- Galaxy, OPL
11
Part No. 70693401ENR5
Introduction
Position 16
C - ProCaptureTM (Advanced lint collection system)
Contact Information
If service is required, contact the nearest Factory Authorized
Service Center.
If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit, contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: +1 (920) 748-3121 Ripon, Wisconsin
When calling or writing about your unit, PLEASE GIVE THE
MODEL AND SERIAL NUMBERS. The model and serial numbers are located on the serial plate. The serial plate will be in the
location shown in Figure 1 .
Date Purchased ______________________________
Model Number ______________________________
Serial Number _______________________________
Please include a copy of your bill of sale and any service receipts
you have.
WARNING
To reduce the risk of serious injury or death, DO NOT
repair or replace any part of the unit or attempt any
servicing unless specifically recommended in the
user-maintenance instructions or in published userrepair instructions that you understand and have the
skills to carry out.
W329
If replacement parts are required, contact the source from where
you purchased your unit or call +1 (920) 748-3950 for the name
and address of the nearest authorized parts distributor.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12
Part No. 70693401ENR5
Introduction
30, T30, 35, T45, 55 Series
1
1
TMB2721N_SVG
1
50, 75 Series
TMB2707N_SVG
120, 170, 200 Series
1
1
170/200
120
TMB2734N_SVG
1. Serial Plate
Figure 1
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13
Part No. 70693401ENR5
Operating Instructions
Operating Instructions
Operating Instructions
30, 35, 50, 55 and 75 Series
WARNING
1
To reduce the risk of fire:
• DO NOT DRY articles containing foam rubber or
similarly textured rubberlike materials.
• DO NOT DRY plastics, anything containing wax or
chemicals such as mops and cleaning cloths, or
anything dry-cleaned at home with a dry-cleaning
solvent.
• DO NOT TUMBLE fiberglass curtains and draperies unless the label says it can be done. If they
are dried, wipe out the cylinder with a damp cloth
to remove particles of fiberglass.
TMB1664N_SVG
T30 and T45 Series
HIGH
TEMP
MED
TEMP
START
LOW
TEMP
NO
HEAT
W076
HIGH
TEMP
MED
TEMP
START
LOW
TEMP
NO
HEAT
WARNING
1
To reduce the risk of serious injury, allow cylinder to
stop before cleaning lint screen.
TMB2572N_SVG
W412
Emergency Stop Button
120, 170 and 200 Series
All on-premises laundry tumble dryers are factory equipped with
an emergency stop button located on the front panel. Refer to
Figure 2 .
1
TMB2488N_SVG
1. Emergency Stop Button
Figure 2
To operate emergency stop button:
•
•
Press red emergency stop button to stop all action.
To restart machine, pull red emergency stop button out and
press START pad or button.
NOTE: Activation of the emergency stop button
stops all machine control circuit functions, but
DOES NOT remove all electrical power from machine.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14
Part No. 70693401ENR5
Operating Instructions
Operating Instructions
WARNING
To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
IMPORTANT: This appliance shall not be used to dry
off solvents or dry cleaning fluids.
To reduce the risk of fire and risk of lint collecting
in exhaust duct, do not operate dryer without lint
filter in place.
W771
IMPORTANT: Make sure fresh air ventilation openings are not blocked or sealed.
2. Load Laundry
NOTE: Remove all objects from pockets such as
lighters and matches.
IMPORTANT: Oil affected items can ignite spontaneously, especially when exposed to heat sources
such as in a tumble dryer. The items become warm,
causing an oxidation reaction in the oil. Oxidation
creates heat. If the heat cannot escape, the items
can become hot enough to catch fire. Piling, stacking or storing oil affected items can prevent heat
from escaping and so create a fire hazard.
IMPORTANT: Load must go through a washer extraction cycle to remove excess moisture to avoid
damage to tumble dryer.
a. Open loading door and load cylinder with laundry. Maximum drying load is:
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
030
30 [13]
T30
30 [13]
035
35 [16]
T45
45 [20]
(per cylinder)
NOTE: Do not dry unwashed items in the tumble dryer.
1. Clean Lint Screen/Compartment
NOTE: For ProCapture models: If lint sensor icon is
on/present, the sensor has detected the lint compartment is full. Remove any accumulated lint. Refer
to ProCapture Maintenance for full instructions.
a. Remove any accumulated lint from the lint screen and
compartment.
b. Close panel tightly against tumble dryer frame and lock
panel securely, if applicable.
WARNING
Pound [Kg]
(per cylinder)
W727
IMPORTANT: Clean lint screen and lint compartment
daily. Failure to clean the lint screen daily will result
in higher than normal temperatures that may damage laundry.
Model
050
50 [25]
055
55 [24]
075
75 [34]
120
120 [55]
170
170 [77]
200
200 [90]
DO NOT OVERLOAD.
NOTE: Overloading causes slow drying and wrinkling.
b. Close loading door. Tumble dryer will not operate with the
door open.
3. Determine Control Type and Temperature Setting
a. Refer to the various controls and follow the instructions
for the appropriate control type.
b. The type of fabric being dried will determine the temperature setting. Consult the fabric care label or fabric manufacturer to determine proper temperature setting.
IMPORTANT: Always follow the fabric care instructions supplied by the garment manufacturer.
4. Start Tumble Dryer
NOTE: Every time the drive motor starts, including
when the motor reverses direction, a motor alignment
occurs which can cause a visible shudder of the cylinder about one second before the motor starts. This is
normal operation.
5. Remove Laundry
a. When the cycle is complete, open door and remove the
laundry.
Reversing Operation
Tumble dryers with the reversing option reduce the tangling of
large pieces of laundry and minimize wrinkling.
To program reversing on or off, refer to programming manual. In
nonreversing mode, the cylinder will always turn clockwise (as
viewed from the front of the tumble dryer). If cylinder is rotating
15
Part No. 70693401ENR5
Operating Instructions
NOTE: One touch drying is available for repetitive
loads. If the START keypad is pressed while the machine is in Idle Mode, when the display is dark, the
tumble dryer will repeat the last drying cycle. If the
cycle time is adjusted before the cycle is started,
the time displayed when the start button was pressed will be used for future cycles.
counterclockwise when reversing is disabled, the tumble dryer
will finish the reversing step, pause, then start in the forward direction. Refer to Programming Manual for more information on
reversing.
Control Instructions
Dual Digital Control
IMPORTANT: To stop the tumble dryer at any time
during the cycle, OPEN DOOR. If the loading door or
lint panel door is opened during the cycle, the heating system will shut off and the motor will stop. To
restart the cycle, both doors must be closed and the
START keypad must be pressed.
7. When the cycle is complete, open door and remove the laundry.
FN Control Suffix
WARNING
To prevent the risk of fire, remove laundry immediately in case of power failure.
W779
NOTE: This machine includes an extended tumble
feature. After 20 minutes, the machine enters extended tumble and will tumble for two minutes every
hour for up to 18 hours or until the door is opened.
TMB2439N_SVG
Figure 3
1. If display has gone blank due to sitting idle, press the DISPLAY keypad.
2. Press the SELECT keypad to choose HIGH, MED, LOW or
NO HEAT temperature.
HIGH
Temperature 190°F [88°C]
MED
Temperature 170°F [77°C]
LOW
Temperature 120°F [49°C]
Galaxy 600 (Vend)
NC, NE, NF, NH, NL, NP, NX, NY, WC, WE, WF, WH, WL,
WP, WX and WY Control Suffixes
3. Press the plus and minus keypads to set HEAT TIME (0 - 99
minutes).
4. Press the plus and minus keypads to set COOL DOWN TIME
(maximum of 15 minutes).
5. Press the REVERSING keypad to change the cylinder rotation setting, if applicable.
6. Press the START keypad to start tumble dryer. Display will
show minutes remaining before end of cycle.
TMB752N_SVG
Figure 4
WARNING
To prevent the risk of fire, never stop a dryer before the end of the drying cycle unless all items
are quickly removed and spread out so that the
heat is dissipated.
1. Select HIGH, MED, LOW or DELICATES by pressing the
appropriate temperature pad.
W756
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16
HIGH
Temperature 190°F [88°C]
MED
Temperature 180°F [82°C]
LOW
Temperature 160°F [72°C]
DELICATES
Temperature 130°F [54°C]
Part No. 70693401ENR5
Operating Instructions
2. Insert the coin(s) in the coin slot or card into the card opening.
3. Press START pad to start tumble dryer.
Galaxy (OPL)
NN Control Suffix
WARNING
To prevent the risk of fire, never stop a dryer before the end of the drying cycle unless all items
are quickly removed and spread out so that the
heat is dissipated.
PROGRAM REVERSING ENERGY HEATING
SAVER
W756
IMPORTANT: To stop the tumble dryer at any time
during a cycle, OPEN DOOR. To restart the tumble
dryer, CLOSE door and press START pad.
4. When the cycle is complete, open door and remove the laundry.
STOP
START
BACK
TMB2644N_SVG
WARNING
Figure 5
To prevent the risk of fire, remove laundry immediately in case of power failure.
1. Press the Up or Down keypad to change cycles.
2. Press START to start selected cycle.
W779
WARNING
NOTE: This machine includes an extended tumble
feature. After 20 minutes, the machine enters extended tumble and will tumble for two minutes every
hour for up to 18 hours or until the door is opened.
To prevent the risk of fire, never stop a dryer before the end of the drying cycle unless all items
are quickly removed and spread out so that the
heat is dissipated.
W756
IMPORTANT: If the loading door or lint panel door is
opened during the cycle, the heating system will
shut off and the motor will stop. To restart the cycle,
both doors must be closed and the START pad must
be pressed.
3. When the cycle is complete, open door and remove the laundry.
WARNING
To prevent the risk of fire, remove laundry immediately in case of power failure.
W779
NOTE: This machine includes an anti-wrinkle/
extended tumble feature. Two minutes after the cycle ends, the machine enters anti-wrinkle and will
tumble without heat for 30 seconds every two minutes for up to an hour or until the door is opened.
After an hour, the machine enters extended tumble
and will tumble for two minutes every hour for up to
18 hours or until the door is opened.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
17
Part No. 70693401ENR5
Operating Instructions
NOTE: This machine includes an anti-wrinkle/
extended tumble feature. Two minutes after the cycle ends, the machine enters anti-wrinkle and will
tumble without heat for 30 seconds every two minutes for up to an hour or until the door is opened.
After an hour, the machine enters extended tumble
and will tumble for two minutes every hour for up to
18 hours or until the door is opened.
Galaxy Touch Vend Control
VC, VE, VF, VH, VL, VP, VX and VY Control Suffixes
Ignition Control Operation and
Troubleshooting
WARNING
70482001 and 70482002 controls cannot be serviced
by the user. If any control failures are detected, the
controls must be replaced by qualified service personnel. Risk of explosion or fire can result if the control module has been opened or with any attempts to
repair it and the warranty is void.
TMB1960R_SVG
Figure 6
1. Select desired cycle on Cycle Preset screen.
2. Add additional time, if desired. Press Next.
3. Select additional options on Additional Options screen, if desired. Press Next.
4. Satisfy vend.
5. Press START.
WARNING
W899
Before troubleshooting the system, check the following items:
- Verify all mechanical and electrical connections are secure and
tight.
- Verify all system wiring is correct.
To prevent the risk of fire, never stop a dryer before the end of the drying cycle unless all items
are quickly removed and spread out so that the
heat is dissipated.
W756
IMPORTANT: If the loading door or lint panel door is
opened during the cycle, the heating system will
shut off and the motor will stop. To restart the cycle,
both doors must be closed and Start must be pressed.
6. When the cycle is complete, open door and remove the laundry.
- Verify there is a proper system ground. The igniter, flame sensor
and igniter module must share a common ground with the burner.
Nuisance shutdowns are often caused by a poor or erratic ground.
- Verify that the system is powered and that the control is calling
for heat.
- If the control proceeds to an error code on the red diagnostic
LED, troubleshoot per the Fault conditions table below:
Fault Conditions
WARNING
To prevent the risk of fire, remove laundry immediately in case of power failure.
W779
LED Indication
Fault Mode
Off
Normal Operation
1 Flash
At Power Up
2 Flashes
Flame Without Call For Heat
3 Flashes
Ignition Lockout
4 Flashes
Manual Reset Error
Steady On
Internal Control Failure
NOTE: The LED will flash on for 1/4 second, then off for
1/4 second during a fault condition. The pause between
fault codes is 3 seconds.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18
Part No. 70693401ENR5
Operating Instructions
NOTE: Additional diagnostics are available through the
control. Refer to appropriate programming manual for
more information.
tion. If this condition persists after an attempt to restart, then the
control must be replaced.
Internal Control Failure
If the control detects an error in its software or hardware, all outputs are turned off and the red LED displays a steady ON condi-
Troubleshooting
Troubleshooting Guide
Symptom
Probable Cause
Control in Lockout Mode
Manual reset of the control is needed. Reset by pushing start
button on front end control with the service door open (single
machines) or with manual programming connector open (stack
machines), if applicable (120-200 models do not have a service
door).
Control does not start, green LED is off
1. 12 VDC present between 12VDC and ground. If not, see machine schematic.
2. 24 VDC present between TH and ground. If not, see machine
schematic.
Thermostat on, no spark or valve
1. High voltage cable connects to control and electrode. Voltage
present at gas valve.
2. Defective control. Check red LED for steady on or flashing
codes.
Valve on, no spark during TFI
1. Shorted electrode.
2. Spark gap not correct. Set to .094-.156 inch.
3. High voltage cable is faulty or has a poor connection.
4. Control failure.
Spark on, no flame
1. Is gas on?
2. 24 VDC at gas valve.
3. Defective control. Check voltage between gas valve and
GND on control.
Flame okay during TFI, no flame sense after TFI
1. Check electrode position and cleanliness.
2. Check high voltage cable.
3. Poor ground at burner.
4. Poor flame, check flame current.
Reset failure
Proper Electrode Location
Proper location of the electrode assembly is important for optimal
system performance. The electrode assembly should be located
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Reset pin is shorted to ground. Verify wiring.
so that the tips are inside the flame envelope and about 1/2 inch
[1.2 cm] above the base of the flame. Refer to Figure 7 .
19
Part No. 70693401ENR5
Operating Instructions
TMB2317K_SVG
Figure 7
Flame Current Measurement
Flame current is the current that passes through the flame from
sensor to ground. To measure flame current, connect a True RMS
or analog DC micro-amp meter to the FC+ and the FC- terminals.
The reading should be 1.0 micro-amps DC or higher. If the meter
reads negative or below “0” on the scale, the meter leads are reversed. Re-connect leads with proper polarity.
Alternately, a Digital Voltmeter may be used to measure the DC
voltage between the FC+ and FC- terminals. Each micro-amp of
flame current produces 1.0 VDC, so a reading of 2.6 VDC would
equate to 2.6 micro-amps.
A good burner ground that matches the control ground is critical
for reliable flame sensing.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
20
Part No. 70693401ENR5
Maintenance
Maintenance
Daily
1. Beginning of day:
a. Inspect gas supply line for gas leaks.
b. Keep machine area clear and free from combustible materials, gasoline and other flammable vapors and liquids.
c. Inspect door switch and door catch before starting operation.
1. Attempt to start machine with door open. Machine
should not start with door open.
2. Close door and start a cycle. Verify that door stays
closed.
3. Open door. Door should open with no more than 15
pounds [1.03 bar] of applied force to the door handle.
Cylinder should stop turning when door is opened.
d. Inspect outside weather hood to make sure dampers move
freely and are not obstructed by any internal or external
objects at the exhaust.
e. Ensure all guards and panels are properly installed.
2. End of day:
a. Clean lint filter to maintain proper airflow and avoid overheating.
WARNING
To reduce the risk of serious injury, do not
open the lint panel while the tumble dryer is in
operation. Before cleaning the lint screen,
open tumble dryer door and allow cylinder to
completely stop.
W410R1
b. Inspect cylinder for foreign objects to avoid damage to
clothing and equipment.
c. Clean dryer drum with an all-purpose cleaner and a damp
cloth. DO NOT LEAVE CLOTHING IN THE TUMBLE
DRYER OVERNIGHT.
d. Clean machine's exposed surfaces with all-purpose cleaner. DO NOT use ammonia-based or vinegar-based cleaners on overlays.
Monthly
1. Inspect electrical connections for looseness. Tighten as required after disconnecting power.
2. Clean electronic controls and coin acceptor of debris, if applicable, and verify ease of operation.
3. Remove lint filter and thoroughly vacuum exhaust duct.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4. Inspect fan, removing any accumulated lint or debris from fan
to maintain proper airflow, avoid overheating and prevent vibration.
5. Wash lint screen with hot water and mild detergent to remove
fabric softener residuee.
6. Inspect door assembly for loose or missing components. Inspect door seal.
7. Inspect steam coil air intake filter, if applicable. Replace if
dirty or damaged.
8. Models equipped with a fire suppression system: Inspect
all inlet hoses for any visible signs of deterioration. Perform
the fire suppression system maintenance test by pressing the
test button in the control box. Refer to Fire Suppression System (Optional Equipment) Maintenance Test for full instructions.
9. ProCapture models: Remove lint sensor cleanout plate from
large debris cleanout trap. Remove any lint and/or debris. Refer to ProCapture Maintenance for full instructions.
Yearly
1. Remove front panel(s) and cylinder. Remove any accumulated lint from all interior surfaces and cylinder baffles.
2. Inspect seals, rollers, bearings, idler assembly, drive pulley
and belt for wear or damage. Replace worn or cracked belts or
damaged components as necessary.
3. Remove any accumulated lint or debris from thermistor, cabinet high limit thermostat, stove high limit thermostat(s), including perforated cover, if present. Lint buildup will act as
an insulator, causing machine to overheat.
4. Remove any accumulated lint or debris from drive and blower
motors.
5. Remove any accumulated lint or debris from burner tubes and
orifice area. Remove burner tubes and clean using water and a
brush.
6. Machines equipped with steam coils and/or heat exchanger kit: Clean the inlet and outlet with a soft brush or clean by
using hot water and, if needed, a mild detergent.
7. Remove any accumulated lint or debris from exhaust duct interior to maintain proper airflow to avoid overheating.
a. Disconnect external duct and duct access covers, if
present.
b. Clean inside of duct and make sure all dampers operate
freely.
c. Reconnect duct and all access covers before returning
tumble dryer to operation.
8. Gas models only: Inspect burner for soft, uniform blue flame.
a. A lazy yellow tipped flame indicates a lack of air.
b. A harsh, roaring, very blue flame indicates too much air.
21
Part No. 70693401ENR5
Maintenance
c. Adjust air shutter, if present, as necessary.
9. Inspect hardware for any loose nuts, bolts, screws.
10. Ensure all guards and panels are properly installed.
11. Inspect all painted surfaces for bare metal. Replace or repaint
if necessary.
12. Run factory test (reference programming manual for procedure details and components tested).
13. Every five years replace belts and fire suppression water inlet
hoses (if applicable).
NOTE: For additional information on programmable options, refer to appropriate programming manual.
75 Series Models
1. Remove lint panel.
ProCapture Maintenance
TMB2746N_SVG
Models with C in the 16th position of the model number
Figure 9
2. Pull lint cover panel down.
1
TMB2747N_SVG
TMB2744N_SVG1
1
Figure 10
3. Remove lint from lint sensor compartment/lint hopper.
TMB2745N_SVG
TMB2748N_SVG
1. Lint Sensor LED
Figure 11
Figure 8
Every 16 cycles (75 series models) or 9 cycles (T30 models) (this
option is programmable 1-70 cycles), or when the sensor senses
lint accumulation, the LED lights up (Galaxy 600) or the icon appears (Galaxy Touch) on the control. There will be 3 more cycles
(programmable 1-6 cycles) before the machine locks out, preventing additional cycles from being run, until the lint is cleaned.
To remove lint and clear sensor, perform the following maintenance.
4. Once a month, remove 8 screws from cleanout plate from
large debris cleanout trap. Remove any lint and/or debris.
Once clean, reinstall cleanout plate.
IMPORTANT: This maintenance can be performed with
power supplied to the machine for routine cleaning.
However, replacement or removal of the lint sensor requires the machine be powered down for a service
task.
NOTE: Loading door should be closed before cleaning
out lint.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
TMB2749N_SVG
Figure 12
5. Reinstall lint cover panel.
6. Reinstall lint panel.
22
Part No. 70693401ENR5
Maintenance
7. Clear lint prompt from control.
TMB2764N_SVG
Figure 15
TMB2765N_SVG
Figure 13
a. Galaxy Touch - Press YES to clear Clean Lint Mode and
reset lint cycle counters.
b. Galaxy - Display will rotate between iS Lint CLEAn.
Any keypad press will result in display transitioning to
no. Pressing any keypad other than START will cause display to rotate between no and yES. Pressing START
while no is displayed will cause control to return to iS
Lint CLEAn display. Pressing START while yES is displayed will result in clearing Clean Lint Mode and/or lint
indicator and will reset lint cycle counters.
3. Dump lint in trash.
4. Reinstall lint drawer.
5. Relock lint drawer.
6. Clear lint prompt from control. Refer to Step 7 under 75 Series Models.
NOTE: After cleaning out lint, if sensor still indicates
lint accumulation, make sure sensor inside lint drawer
is clear of lint.
Fire Suppression System (Optional
Equipment) Maintenance Test
WARNING
NOTE: After cleaning out lint, if sensor still indicates
lint accumulation, make sure sensor inside debris
cleanout trap is clear of lint.
Electrical shock hazard can cause death or serious
injury. To reduce the risk of electric shock, disconnect all electric power to appliance and accessories
before servicing.
T30 Series Models
1. Unlock lint drawer.
W929
WARNING
Electrical shock hazard. Can cause death or serious
injury. If the water dispensing system is activated do
not attempt to operate the dryer. If the water dispensing system is activated have the dryer inspected by a
qualified agency before operating the dryer.
TMB2763N_SVG
Figure 14
2. Pull lint drawer out and remove from machine.
•
•
•
•
CALL THE FIRE DEPARTMENT.
DO NOT disconnect electric power to the dryer.
DO NOT disconnect water to the dryer.
DO NOT touch the dryer.
W932
NOTE: Fire suppression system only available on gas
and steam models.
NOTE: If the auxiliary alarm output is connected to a
separate alarm system, disconnect prior to performing
the fire suppression system maintenance test.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
23
Part No. 70693401ENR5
Maintenance
To ensure proper operation, the fire suppression system must be
tested every month. If the system test does not perform as indicated:
1. Discontinue use of the tumble dryer.
2. Refer to Troubleshooting Manual or contact a qualified service person.
3. Restore the fire suppression system to proper working order
before using tumble dryer.
Create a maintenance record with a check box for pass, the date
and a signature. Store this record in an area where it will not be
damaged, but is easily accessible to person performing tests.
NOTE: Failure to maintain the fire suppression system
will void the tumble dryer warranty.
NOTE: The auxiliary output is activated during the fire
suppression system maintenance test sequence. Consider this fact prior to testing the system every three
months. (Example – If the external system uses the
auxiliary output to call the fire department, inform the
fire department before and after the fire suppression
system maintenance test. If the external system uses
the auxiliary output to activate a building sprinkler, disconnect auxiliary output prior to test.)
1. If the auxiliary alarm output is connected to a separate alarm
system, disconnect prior to performing the fire suppression
system maintenance test.
2. Remove any lint from the lint compartment.
3. Ensure temperature sensors are free of lint.
4. Place a load of dry towels in the tumble dryer. Refer to Table
1 for proper load size. Ensure the cylinder baffles are to the
left and right of the spray manifold located at the center top of
the cylinder.
5. Unlock the fire suppression system control box.
6. Press and hold the test button, verify the light is on, this
should take approximately five seconds. Refer to Figure 16 .
After a one-second pause water should begin to spray into the
cylinder.
7. After 15 seconds of water spray, press and hold the reset button until water spray is off and light is off. This should take
approximately one second. Refer to Figure 16 and Figure 17 .
8. Immediately remove and weigh the load. Refer to Table 1 for
acceptable weight range. If less than minimum pounds indicated in Table 1 , the fire suppression system has failed the
maintenance test. Refer to the Troubleshooting Manual.
IMPORTANT: If the fire suppression system failed
the maintenance test, DO NOT operate the tumble
dryer.
CAUTION
Dry
Weight
Wet
Weight
Minimum
Weight
lbs.
[kg]
lbs.
[kg]
lbs.
[kg]
30
15 [9]
20-24
[9-11]
18 [8]
35
25 [11]
30-34
[14-15]
28 [13]
55
25 [11]
33-37
[15-17]
31 [14]
50
25 [11]
40-44
[18-20]
35 [16]
75
40 [18]
57-61
[26-28]
52 [24]
120
60 [27]
75-79
[34-36]
70 [32]
170
80 [36]
95-99
[43-45]
90 [41]
Clean up any water spilled during testing to avoid
personal injury.
W487
3
2
1
TMB2452N_SVG2
1. Test Button
2. Light
3. Reset Button
Figure 16
To perform the fire suppression system maintenance test:
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Table 1 continues...
24
Part No. 70693401ENR5
Maintenance
200
Dry
Weight
Wet
Weight
Minimum
Weight
lbs.
[kg]
lbs.
[kg]
lbs.
[kg]
100 [45]
115-119
[52-54]
110 [50]
Table 1
9. Clean up any water on the floor.
10. Lock the fire suppression system control box.
11. If the separate alarm option is being used, reconnect the auxiliary alarm output.
12. If the cold weather fire suppression system relocation kit (part
no. 44340301) is installed on this tumble dryer, purge water
out of the lines to prevent freezing. Disconnect at couplers.
Refer to instructions provided with kit.
13. Re-condition fire suppression test load by running through a
final extract cycle in a washer-extractor to prevent damage to
tumble dryer.
14. Load laundry and start the tumble dryer to dry the test load.
15. On maintenance record, check box if fire suppression system
passed the test, date and sign record.
1
2
TMB2010N_SVG
1. Spray Manifold
2. Water Spray
Figure 17
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
25
Part No. 70693401ENR5
Before You Call for Service
Before You Call for Service
Won’t Start
Won’t Heat
Clothes Not Dry
Possible Reason – Corrective Actions
•
Insert correct coin(s) or valid card if applicable.
•
Close the loading door tightly.
•
Close lint panel tightly.
•
Press the PUSH-TO-START or START pad/button.
•
Be sure power cord is plugged all the way into the electrical outlet and hard or direct wire connections are
tight.
•
Check the main fuse and circuit breaker.
•
Check fuses located in the machine.
•
Insufficient airflow.
•
Gas shut-off valve in OFF position.
•
Are controls properly set?
•
Broken drive belt. Call the service person.
•
•
Tumble dryer is in Cool Down Mode.
•
•
Lint screen clogged. Clean lint screen.
•
•
Exhaust duct to outside is blocked. Clean out.
•
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
ProCapture models - lint compartment full. Clean lint
compartment and clear prompt on control.
26
Part No. 70693401ENR5
Removing Tumble Dryer from Service
Removing Tumble Dryer from Service
1. Turn off electrical supply external to machine.
2. Turn off gas supply external to machine.
3. Turn off manual gas shut-off valve on machine.
4. Turn off steam supply external to machine.
5. Remove all electric, gas and steam connections.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
27
Part No. 70693401ENR5
Disposal of Unit
Disposal of Unit
This appliance is marked according to the European directive
2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE).
This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste. Refer to Figure
18 . Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly will help prevent potential negative consequences for the environment and human
health which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to
conserve natural resources. For more detailed information about
recycling of this product, please contact the local city office,
household waste disposal service, or the source from which the
product was purchased.
MIX1N_SVG
Figure 18
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
28
Part No. 70693401ENR5
">