Packing List
Printer(eg:iD2P)
AC Adapter
Power Cord
Label Roll
CD
Quick Start Guide
USB Cable
Quick Start Guide
iD2P
iD2X
!Note: The packing items are actually based on the order.
Appearance and Components
Front
①
②
③
① Display
② Func�on Bu�on
③ Status Indicator
④ Cover Open Levers
⑤ Front Paper Outlet
Inside ⑤
⑥
④
④
①
②
⑤
Cau�on:
This is a Class A product. In a domes�c environment this
product may cause radio interference in which the user
may be required to take adequate measures.
Rear
① USB Port (Type A)
② USB Port (Type B)
③ Ethernet Port
④ Back Paper Outlet
⑤ Power Receptacle
⑤ ⑥ Serial Port
①
②
Xiamen Hanin Electronic Technology Co., Ltd.
ADD: 5F, 8#, Aide Airport Industrial Park, Huli District, Xiamen, China.
WEB:www.idprt.com
-1-
③④
⑥
③
① Moveable Label Sensor
② Moveable Label Guides
③ Platen
④ Upper Sensor
⑤ Serrated Knife
⑥ Print Head Module
!Note: The interface shown in the figure above is for reference only.
-2-
FCC WARNING:
This device complies with part 15 of the FCC Rules.
Opera�on is subject to the following two condi�ons:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause unde
sired opera�on.
Any changes or modifica�ons not expressly approved
by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protec�on against
harmful interference when the equipment isoperated
in a commercial environment. This equipment
generates, uses, and canradiate radio frequency
energy and, if not installed and used in accordance
with the instruc�on manual, may cause harmful
interference to radio communica�ons. Opera�onof
this equipment in a residen�al area is likely to cause
harmful interference in whichcase the user will be
required to correct the interference at his own
expense.
-- Reorient or relocate the receiving antenna.
-- Increase the separa�on between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV tech
nician for help.
To maintain compliance with FCC’s RF Exposure
guidelines, This equipment should be installed and
operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
Paper Loading
1. Pull and li� the cover.
Paper Loading
2. Put the paper roll into the axis by with
the inner diameter of the paper roll.
1
1 inch
2
5.Press the cover lock and close the cover slightly.
1.5 inches
Locking Tab
!Note:
1.After lifting the top cover, the locking tab will hold the top cover to
prevent the top from falling and hurting hands.
2.When using the 1 inch paper roll, the font of "1 CORE" should be
upward; when using the 1.5 inch paper roll, the axis should be turned
180 degrees and the font of "1.5 CORE" should be upward.
3. Pull the roll holders open and place the 4. Pass the label through the label guides,
roll between them.
then adjust guides to adapt to the label
width.
Cau�on: the tear bar
of this printer contains
a sharp edge. Please
do NOT touch it.
-3-
Power Connec�ng
1. Connect B-U port of printer to A-U port of computer by USB cable.
2. Connect the power cord to the power adapter.
3. Connect the other end of the power cord to a nearby socket.
3
1
2
Varies by region
!Note: Please refer to windows driver installation in iD2P_iD2X User
Manual.
-4-
">