INSTALLATION
BLACK UNIVERSAL L.E.D. BATTERY GAUGE
PARTS INCLUDED
1
Battery Gauge — Black
1
Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING
THE USE AND CARE OF THIS PRODUCT.
ATTENTION! This indication alerts you to the fact that ignoring the contents
described herein may negatively affect product performance and
functionality.
CAUTION!
This indication alerts you to the fact that ignoring the contents
described herein can result in potential injury or material
damage.
TOOLS SUGGESTED
Glass Cleaner, Clean Rag, Splicing and Insulating Supplies, Drill and Drill Bits
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition.
ATTENTION! A factory service manual may be helpful in performing this installation.
Do not attempt to perform this installation if you are not confident in
your ability to complete all of the steps in the procedure; consult a
trained technician.
NOTE: This universal battery gauge is designed to indicate the safe charging
levels of any 12 volt alternator/battery powered motor vehicle
electrical system. The gauge is equipped with 9 LEDs with an
automatic “day/night” brightness control. The gauge is calibrated in
1/2 volt increments from 8–16 volts.
—The green LED zone of 12.5–14.5 volts indicates a safe charging
range level for the entire electrical circuit the battery gauge is
reading.
—The high and low yellow LEDs warn of an over or under charging
problem.
4218
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof9of9Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley9Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights
reserved.
—The extreme high and low flashing red LEDs warn of an impending
electrical system failure.
Dcont.D
4218921HD90911
kuryakyn.con
lfiirvallvn·
STEP 2
After choosing a location, if you choose to hide the power wire, drill a 3/16” diameter wire access
hole in the center of the mounting location. Clean the mounting area.
CAUTION!
MEASURE TWICE – DRILL ONCE. Double check all reference marks made
on the mounting location BEFORE drilling. Kuryakyn will not be responsible for
incidental or consequential damages resulting from this installation
STEP 3
Feed the wire through the access hole, then peel off the adhesive backing and stick the gauge into
position.
ATTENTION! Ensure the area of installation is free of grease, oil, dirt or other debris to ensure proper
adhesion. Küryakyn WILL NOT issue a warranty on any parts lost due to improper
installation.
ATTENTION! The adhesive will not bond correctly if applied at temperatures less than 50°F. Do not
attempt this installation in temperatures less than 50°F.
STEP 4
Find a power lead. After confirming with a test light that it is only “on” when the ignition key is on,
attach the red wire to the power lead.
STEP 5
Find a good circuit ground wire and attach the black wire from the gauge to the ground wire.
STEP 6
Carefully insulate all connections.
ATTENTION! Secure all wiring away from any moving parts, pinch points or extreme heat. Küryakyn
WILL NOT issue a warranty on any electrical component that fails due to pinched,
crimped, broken, abraded, melted or frayed wires.
PAGE
2
Ride On!
UNIVERSAL L.E.D. BATTERY GAUGE
INSTALLATION
">