ELKAY EZLMSN-EDFPVM214DK Fountain User Manual

EZLMSN-EDFPVM214DK
LZLMSN-EDFPVM214DK
INSTALLATION & USE MANUAL
SOFT SIDES® Fountain with Vandal Resistant Bubbler
and Vandal Resistant Water Dispenser
EZLMSN-EDFPVM214DK
LZLMSN-EDFPVM214DK
INSTALLER
(Shown with optional ACCESS12X19-75 access panel.)
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain fittings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building’s plumbing circuits.
Page 1
2000001510 (Rev. A - 03/24)
Figure 1 - Rough-in Dimensions
2000001510 (Rev. A - 03/24)
Page 2
**NEW INSTALLATIONS MUST USE GROUND FAULT CIRCUIT INTERRUPTER *GFCI)
REDUCE HEIGHT BY 3 INCHES FOR INSTALLATION OF CHILDREN’S ADA FOUNTAIN
EZLMSN-EDFPVM214DK
LZLMSN-EDFPVM214DK
EZLMSN-EDFPVM214DK
LZLMSN-EDFPVM214DK
TO BUBBLER
REQUIRED TOOLS AND MATERIALS
These tables show special tools and/or additional
materials (not provided) which are necessary to
complete installation of these units:
Special Tools
Item
10
Quantity
Description
NONE
Additional Materials Not Included
11
10
11
10
10
TO BOTTLE
FILLER
12
Quantity
Item
Description
1
Unplated copper inlet pipe
2
Service Stop
3
90° 1-1/4” Drain Line
4
1-1/4” Tee Drain Line
1
1
1
1
1. Make water supply connections (Fig. 10). Install a
shut-off valve and union connection to building watersupply (valve and union not provided). Turn on water
supply and flush the line thoroughly.
Caution: DO NOT SOLDER tubes inserted into the
strainer or filter head as damage to the o-rings may
result.
21
Figure 2 - EZLMSN-EDFPVM214DK Tube Routing
TO BUBBLER
2. Install mounting frame (instructions supplied with
mounting frame.)
3. (For LZLMSN-EDFPVM214DK) Install the filter head
to the bracket, then install filter bracket on mounting
frame (Fig. 8), plumb from the filter outlet using the ¼”
elbow, poly tubing and ¼ x ¼ x ¼” tee, install filter.
10
10
11
3a. (For EZLMSN-EDFPVM214DK) Install ¼” tee,
copper tubing and strainer per (Fig. 2).
10
TO BOTTLE
FILLER
4. Hang main panel on mounting frame hanger. Make
sure the poly tube do not get pinched between the panel
& mounting frame. Ensure the panel engages at the top.
Align fountain holes with mounting frame holes.
19
FILTER
ASSEMBLY
5. Remove protective coating from main panel.
WATER
INLET
6. Installing water Dispenser Place the unit into the
stainless panel and frame. Align the holes in the water
dispenser with the nuts in the panel. Attach the dispenser to the panel using four (4) supplied 1/4 x 20 screws.
Figure 3 - LZLMSN-EDFPVM214DK Tube Routing
Page 3
2000001510 (Rev. A - 03/24)
EZLMSN-EDFPVM214DK
Connecting Catch Basin Waste Drain
Installing the drain is highly recommended to prevent
basin overflow.
LZLMSN-EDFPVM214DK
3. Trial fit the strainer. If the strainer does not fit, carefully
open the size of the hole. If it fits well, place a small
amount of plumbers putty around the lip of the strainer
flange and insert it into the hole.
The following steps cover the installation of the drain.
1. Remove the two screws attaching the drain basin to
the water dispenser. Remove the drain basin.
4. Install the O-ring over the strainer threads.
2. Place the drain basin on a flat, hard surface, such as
a piece of sacrificial wood. Carefully drill a hole in the
basin using a 1" hole saw using the centering‑dimple
as a guide to center the hole saw.
Note: Do not use a 1-1/8" hole saw as this will make the
opening too large.
5. Thread the strainer into the drain adapter.
Needle‑nose pliers can be used to hold the drain
adapter from the top while tightening. Ensure that
the connection creates a watertight seal. The drain
adapter must be facing to the left.
Note: Twisting the strainer instead of the drain adapter
can compromise the seal created by the plumber's
putty.
2000001510 (Rev. A - 03/24)
Page 4
EZLMSN-EDFPVM214DK
LZLMSN-EDFPVM214DK
8. Connect the drain adapter into the household waste
drain pipe.
If the p-trap is located inside a sealed walled, it must
have permanently-glued joints. If the p-trap is in an
accessible location, a standard non-glued p-trap is
acceptable.
Install the water dispenser’s front cover.
9. Line up the front panel with the dispenser frame and
attach using the flathead screws and a 3/32” hex
wrench.
6. Attach one end of the 3/4 inch flexible drain hose to
the 3/4 inch barbed drain adapter connection using the
supplied hose clamp. The supplied flexible drain is 13
inches long. If a longer drain hose is required, it must
be installer-supplied.
10. Install the metal grate cover using the 4 Screws.
Note: Always consult local plumbing codes prior to installation.
7. Place the drain basin back into the water dispenser
and reinstall the two screws.
Page 5
2000001510 (Rev. A - 03/24)
EZLMSN-EDFPVM214DK
23,24
5
LZLMSN-EDFPVM214DK
1. Install fountain with (4) 5/16-18 HHMS & (4) 5/16-18
nuts (provided) (Fig. 5). Connect the ¼” water lines from
fountain to the remaining opening on the tee (cut line to fit
as needed).
2. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip
trap. Trap on the bottle filler side must be 1-1/2” O.D.
(provided by others).
17
13
3. Make final water supply connections.
2
14
8
Figure 4 - Upper Panel Installation
9
4. These products are designed to operate on 20-105
PSI supply line pressure. If inlet pressure is above 105
PSI, a pressure regulator must be installed in the supply
line.
Caution: Any damage caused by connecting these products to a supply line with pressure lower than 20 PSI or
higher than 105 PSI IS NOT covered under warranty.
5. Verify proper dispensing from the bottle filler by
placing a cup, under the water dispenser spout and
press the button and verify water dispenses. Note: the
first initial dispenses might have air in the line which may
cause a sputter. This will be eliminated once all air is
purged from the line. A steady stream of water assures all
air is removed. Check for leaks.
3
18
18
6. Check stream height from bubbler. Stream height is
factory set for 35 PSI supply. If supply pressure varies
greatly from this, remove push button (Item 5 - Fig. 8)
and adjust the screw on the regulator (Item 4 - Fig. 8). To
remove push button, loosen set screw (Item 7 - Fig. 8) on
bottom of the sleeve (Item 6 - Fig. 8) and pull out on the
button. Clockwise adjustment will raise stream height and
counterclockwise movement will lower stream height. For
best adjustment stream should hit basin approximately
6-1/2” from the bubbler. Reassemble the push button by
pushing in on button and tighten the set screw (Item 7 Fig. 8) in the sleeve (Item 6 - Fig. 8).
7. Install the bottom cover plate on fountain (Fig. 4).
8. Tighten back panel screws (Item 9 - Fig. 4).
9. Optional: Mount optional panels. Mount bracket on
wall per rough-in instructions. Slide tongue of panel under
edge of already installed panel. Tighten screws.
Once the installation is complete, the water has been
turned on, and any trapped air has been bled from the
system re-check for any water leaks.
View From Rear
20
Figure 5 - Fountain Installation
2000001510 (Rev. A - 03/24)
Page 6
EZLMSN-EDFPVM214DK
LZLMSN-EDFPVM214DK
Once the installation is complete, the water has been
turned on, and any trapped air has been bled from
the system re-check for any water leaks.
2
1
3/8”
Water
Inlet
BASIN
1/4” tube
(if required – not included)
Locknut
1
Filter Head Assembly
used after 01/01/2021
VANDAL-RESISTANT BUBBLER DETAIL
Fig. 7
NOTE:
When installing replacement bubbler and
pedestal, tighten locknut only to hold parts
snug in position.Do Not overtighten.
WATERSENTRY® PLUS FILTER PARTS LIST
(See Fig. 7)
Figure 6 - Bubbler Details
ITEM
NO.
PART NO.
DESCRIPTION
1
2
51300C
51469C
Filter Assy-3000 Gal.
Assy-Filter & Brkt includes Fltr Head/
Mtg Brkt/John Guest Fittings/Screws
16
4
5
15
6
7
Fountain Push Button Assembly
Page 7
2000001510 (Rev. A - 03/24)
EZLMSN-EDFPVM214DK
LZLMSN-EDFPVM214DK
PARTS LIST
ITEM
NO.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
98481C
28783C
LK464
98530C
45960C
45663C
75672C
112627543890
111008343890
56092C
1000001994
55996C
2000001508
55000665
40045C
28823C
56280C
75560C
1000001772
111577343890
62223C
1000002062
Kit - Vandal-Resistant Bubbler Assy
Fountain Arm - Long
Drain
Kit - Regulator/Nut/Holder
Push Button
Push Button Sleeve
Screw - Cap #6-32 x 5/16
Screw - #10-24 x .50 PHTC
Screw - #10-24 x .62 HHSM
Poly Tubing 1/4” (Cut To Length)
Kit - Tee 1/4 x 1/4 x 1/4 (3 Pack)
Strainer
Back Panel Assembly
Bottom Cover Plate - Long
Hex Nut
Regulator Mounting Bracket
Edge Trim - Chrome
Screw - 5/16-18 x 1.00 HHMS
Kit - Elbow 1/4 x 1/4 (3 Pack)
Nut - Hex 5/16-18
Copper Tube - 3/8” Cut to Length
Kit - Tee 1/4 x 1/4 x 3/8 (3 Pack)
24
27
26
24
24
24
MAIN ENCLOSURE
ASSEMBLY
ALCOVE
ASSEMBLY
25
25
25
Figure 8
28
28
Figure 9
2000001510 (Rev. A - 03/24)
Page 8
EZLMSN-EDFPVM214DK
LZLMSN-EDFPVM214DK
37
OPERATION OF QUICK CONNECT FITTINGS
36
SIMPLY
PUSHIN
IN
SIMPLY PUSH
TUBE TO
TUBE
TOATTACH
ATTACH
35
33 34
TUBE
TUBEIS
IS SECURED
SECURED
INPOSITION
POSITION
IN
PUSH
PUSHIN
IN COLLET
COLLET
TORELEASE
RELEASE TUBE
TUBE
TO
31
A
A
29
B
C
PUSHING
BEFORE
PUSHINGTUBE
TUBE IN
IN BEFORE
PULLING
TO
PULLING IT
IT OUT
OUT HELPS
HELPS TO
RELEASE
RELEASE TUBE
TUBE
30
Figure 12 – Quick Connect Fittings
Installation Package
The components for installation are packed in
three separate boxes, regardless of the type
of unit being installed. The boxes contain the
following:
32
Figure 10 - Bottle Filler Push Button Assembly
1/4” O.D. TUBE
WATER INLET
TO COOLER
3/8” O.D. UNPLATED COPPER TUBE CONNECT
COLD WATER SUPPLY
Box No. 1: Wall Frame(s)
Box No. 2: Fountain(s), Arm(s) and Panels
Box No. 3: Water Dispenser
BUILDING WATER
INLET
Additional materials, as noted in the Parts List,
are also shipped in these boxes.
NOTE: WATER FLOW
DIRECTION
SERVICE STOP
(NOT FURNISHED)
Figure 11 – Water Supply Connections
REPLACEMENT PART LIST
ITEM
NO.
PART NO.
DESCRIPTION
23
NS
24
25
26
27
28
29
30
31
32
33
34
35
36
37
98546C
1000004698
2000001260
1000005392
56331C
70793C
1000001812
50985C
45960C
45663C
75672C
40045C
28308C
45736C
10031C
66822C
Kit - Aerator Replacement
Fitting - Hose to Trap
Kit - Alcove
Kit - Drain
Connector
Elbow 1/4 O.D. X 90
Kit - Bottle Filler Drain
Regulator Holder
Push Button
Push Button Sleeve
Screw - Cap #6-32 X 5/16
Hex Nut
Washer - Spacer 2.00 OD
Nut - Reg Mount
1-1/8-24 Retaining Nut
Regulator Assy. (1.0GPM)
NS = NOT SHOWN
TROUBLESHOOTING & MAINTENANCE
Orifice Assembly: Mineral deposits on orifice can
cause water flow to spurt or not
regulate. Mineral deposits may
be removed from the orifice by
poking with a small round file
not over 1/8” diameter, or using
a small diameter wire.
DO NOT file or cut orifice material.
Stream Regulator: If orifice is clean, regulate flow as
in Step 14 of the installation instructions. If replacement
is necessary, see parts list for correct regulator part
number.
Actuation of Quick Connect Water Fittings: Cooler
is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the fitting,
relieve water pressure, push in on the gray collar while
pulling on the tubing. (See Fig. 11) To insert tubing,
push tube straight into fitting until it reaches a positive
stop (approximately 3/4”).
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
ELKAY MANUFACTURING COMPANY • 1333 BUTTERFIELD ROAD SUITE 200 DOWNERS GROVE, IL 60515 • 630.574.8484 • www.elkay.com
Page 9
2000001510 (Rev. A - 03/24)
">