x Restoration Procedure
Restoration
14 V.1
Technical Data Sheet
Restoration System Data Sheet
This system data sheet specifies the paint system recommended by Spies Hecker and describes the steps to
be taken in the refinishing of Classic or Antique Cars.
This product is for professional painting of vehicles only.
Technical Data Sheet No. 901.5. Mar. 2014
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved
Restoration
14 V.1
Substrate
Pretreatment:
When refinishing antiques or classic cars, the old paintwork must be removed down to the bare metal.
Rust spots are then sanded out, and if possible the entire vehicle should be sandblasted. Any metalwork
repairs are carried out, and the surface to be painted is washed down with Silicone Remover. If the
vehicle is left to stand before work is continued, the sanding and cleaning should be repeated prior to
painting, as new rust spots can form very quickly on untreated surfaces, in particular at high humidity.
Note:
Before puttying, a primer and surfacer must always be applied to the vehicle. This is the only way that
the corrosion protection of the paint system, which is so important with such a vehicle, can be
guaranteed.
Paint System
®
®
1. Prime the entire surface with Priomat Wash Primer 4075 Gray (with Priomat Activator 4076) or
®
®
when necessary use Permasolid EP Primer Surfacer 4500 Light Gray (with Permasolid EP
®
Hardener 4501). When using Permasolid EP Primer Surfacer 4500 Light Gray the bare metal
substrate must be free of any oxidation and must be primed within 30 minutes of sanding and/or
sandblasting. See specific product TDS for further instructions.
®
2. Apply Permasolid Vario Surfacer 8590 to the entire area. Allow to fully cure. Then, sand with180
grit sandpaper. 2.0 mils must remain after sanding.
3. Any sanded through spots must be primed and surfaced once more as described in previous
points.
®
4. The puttied, sanded areas and any uneven spots are surfaced with Raderal Spray Polyester 3508.
5. After drying, the area is sanded with a random orbital sander and P 240, and by hand on corners
and edges.
6. The surface is then blown clean with compressed air and washed down with Permaloid  Silicone
Removers 7087 or 7010 Slow, Permahyd Silicone Remover 7085, or Permahyd Silicone
®
Remover 7096. Sanded through bare metal spots must be primed with Priomat Wash Primer 4075
Gray.
®
7. After this pretreatment, the area is coated again with Permasolid Vario Surfacer 8590. After
drying, the surfacer is sanded with a random orbital sander and P 500-800, and by hand on corners
and edges.
8. The surface is then blown clean with compressed air, washed down with Permaloid  Silicone
Remover 7010 Slow, Permahyd Silicone Remover 7085, or Permahyd Silicone Remover 7096
and wiped with a tack cloth.
®
®
9. The topcoats to be utilized are: Permacron Series 293/295 or Permahyd Hi-TEC 480 followed
®
®
with Permacron /Permasolid 2K Clear Coat.
10. To achieve the best finish, the clear coat can be sanded with P 800 when it has hardened well after
air drying or low baking, and the paintwork completed with a second application of
®
®
Permacron /Permasolid 2K Clear Coat.
The finished vehicle should be allowed to stand in a well-heated and ventilated place for a few days,
especially in the autumn and winter months, before being handed over to the customer.
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved
Restoration
14 V.1
Important Regulatory Information


For industrial use only by professional, trained painters. Not for sale to or use by the general
public. Before using, read and follow all label and MSDS precautions. If mixed with other
components, mixture will have hazards of all components. Do not sand, flame cut, braze or
weld dry coating without a NIOSH approved air purifying respirator with particulate filters or
appropriate ventilation, and gloves.
Any analytical results set forth herein do not constitute a warranty of specific product features or of the
product’s suitability for a specific purpose. All products are sold pursuant to our general conditions of
sale. We hereby disclaim all warranties and representations, express or implied, with respect to this
product, including any warranty of merchantability or fitness for a particular purpose. This product is
protected by patent law, trademark law, copyright law, international treaties and/or other applicable law.
All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties.
SPIES HECKER, INC.
47818 West Anchor Court
Plymouth, MI 48170
Tel. 800-447-7437 (800-44-SPIES)
Fax 734-354-3405
www.SpiesHeckerUSA.com
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement