Lenco SCD-100BK Portable FM Radio User Manual

Model SCD-100BK
User manual – Portable FM radio with CD MP3, Bluetooth, USB and SD player
Gebruikshandleiding – Draagbare FM-radio met CD MP3, Bluetooth, USB- en SD-speler
Bedienungsanleitung – Tragbares FM-Radio mit CD/MP3-, Bluetooth-, USB- und SD-Player
Mode d’emploi – Radio FM portative avec CD MP3, Bluetooth, USB et lecteur de carte SD
Manual de usuario – Radio FM portátil con CD MP3, Bluetooth, USB y reproductor SD
SCD-100BK
English
CAUTION:
Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
PRECAUTIONS BEFORE USE
KEEP THESE INSTRUCTIONS IN MIND:
1.
Do not cover or block any ventilation openings. When placing the device on a shelf, leave 5 cm (2”) free space
around the whole device.
2.
Install in accordance with the supplied user manual.
3.
Keep the device away from heat sources such as radiators, heaters, stoves, candles and other heat-generating
products or naked flame. The apparatus can only be used in moderate climates. Extremely cold or warm
environments should be avoided. Working temperature between 0° and
35° C.
4.
Avoid using the device near strong magnetic fields.
5.
Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart the device following
the instruction manual. During file transmission, please handle with care and operate in a static-free environment.
6.
Warning! Never insert an object into the product through the vents or openings. High voltage flows through the
product and inserting an object can cause electric shock and/or short circuit internal parts. For the same reason, do
not spill water or liquid on the product.
7.
Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.
8.
The apparatus shall not be exposed to dripping or splashing and make sure that no objects filled with liquids, such as
vases, are placed on or near the apparatus.
9.
Do not use this device when condensation may occur. When the unit is used in a warm wet room with damp, water
droplets or condensation may occur inside the unit and the unit could maybe not work properly; let the unit stand in
power OFF for 1 or 2 hours before turning on the power: the unit should be dry before getting any power.
10. Although this device is manufactured with the utmost care and checked several times before leaving the factory, it is
still possible that problems may occur, as with all electrical appliances. If you notice smoke, an excessive build-up of
heat or any other unexpected phenomena, you should disconnect the plug from the main power socket immediately.
11. This device must operate on a power source as specified on the specification label. If you are not sure of the type of
power supply used in your home, consult your dealer or local power company.
12. Keep away from rodents. Rodents enjoy biting on power cords.
13. To clean the device, use a soft dry cloth. Do not use solvents or petrol based fluids. To remove severe stains, you
may use a damp cloth with dilute detergent.
14. The supplier is not responsible for damage or lost data caused by malfunction, misuse, modification of the device or
battery replacement.
15. Do not interrupt the connection when the device is formatting or transferring files. Otherwise, data may be corrupted
or lost.
16. If the unit has USB playback function, the usb memory stick should be plugged into the unit directly. Don’t use an usb
extension cable because it can cause interference resulting in failing of data.
17. The rating label has been marked on the bottom or back panel of the apparatus.
18. This device is not intended for use by people (including children) with physical, sensory or mental disabilities, or a
lack of experience and knowledge, unless they’re under supervision or have received instructions about the correct
use of the device by the person who is responsible for their safety.
19. This product is intended for non professional use only and not for commercial or industrial use.
20. Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position
vibrations or shocks or by failure to follow any other warning or precaution contained within this user manual will not
be covered by warranty.
21. Never remove the casing of this apparatus.
22. Never place this apparatus on other electrical equipment.
23. Do not allow children access to plastic bags.
24. Only use attachments/accessories specified by the manufacturer.
25. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as the power supply cord or the plug, when liquid has been spilled or objects have fallen into the
apparatus, when the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
26. Prolonged exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss.
3
27.
If the product is delivered with power cable or AC power adaptor :

If any trouble occur, disconnect the AC power card and refer servicing to qualified personnel.

To completely disconnect the power input, the mains plug of the apparatus shall be disconnected from the
mains, as the disconnect device is the mains plug of apparatus.

Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the cable’s exit point.
Do not place heavy items on the power adaptor, which may damage it. Keep the entire device out of children’s
reach! When playing with the power cable, they can seriously injure themselves.

Unplug this device during lightning storms or when unused for a long period.

The socket outlet must be installed near the equipment and must be easily accessible.

Do not overload ac outlets or extension cords. Overloading can cause fire or electric shock.

Devices with class 1 construction should be connected to a main socket outlet with a protective earthed
connection.

Devices with class 2 construction do not require a earthed connection.

Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord. This can cause
a short circuit.

Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or electric shock.
28. If the product contains or is delivered with a remote control containing coin / cell batteries:
Warning:

“Do not ingest battery, Chemical Burn Hazard” or equivalent working.

[The remote control supplied with] This product contains a coin / button cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical
attention.
29. Caution about the use of Batteries:

“Do not ingest battery, Chemical Burn Hazard” or equivalent working.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use,
storage or transportation.

Replacement of a battery with an incorrect type that can result in an explosion or the leakage of flammable
liquid or gas.

Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an
explosion.

Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or
that leakage of flammable liquid or gas.

A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable
liquid or gas.

Attention should be drawn to the environmental aspects of battery disposal.
INSTALLATION
• Unpack all parts and remove protective material.
• Do not connect the unit to the mains before checking the mains voltage and before all other connections have been
made.
4
WARNING
Class 1 Laser Product
Warning : Do not touch the lens.
WARNING: When participating in the traffic listening to a personal music player can make the listener
less aware of potential dangers such as approaching cars.
WARNING: To prevent possible hearing damage, do not listen at high volume levels for long periods.
5
FRONT & TOP
1. IR RECEPTION WINDOW
2.
3.
4.
5.
6.
7.
8.
9.
DISPLAY
Display the unit operation status and information
CD DISC COMPARTMENT DOOR
VOL +/VOL Adjust the main volume
FOLDER+/10+
CD/USB/SD: During playback, press to search to the current track number increase by 10
Press and hold will search to the next folder (folder up)
RANDOM
CD/USB/SD: During playback, press to start the random playback. Press again will return to normal playback
FM ST/MO
In FM mode, press to toggle between stereo and force mono.
PRESET
FM: Press to recall the FM preset channel operation
REPEAT
CD/USB/SD: During playback, press to start the repeat playback operation
6
10. PROG./MEM.
FM: Press to enter the preset channel storage operation
CD/USB/SD: In stop mode, press to enter the program playback setup
11. STOP
Press to stop the CD/USB/SD playback operation
/PAIR
12.
CD/USB/SD/BT: Press to toggle between pause and resume playback operation.
BT: Press and hold will disconnect the current connection and start to search another new Bluetooth device
13. STANDBY
Short press to turn on. Press again to turn off and go to Standby mode
14. SOURCE
Press this key will choose different modes of operation: FM/CD/USB/SD/BT/AUX
/TUN- and
/TUN+
15.
FM: Short press to tune to a different frequency
Press and hold to scan the next available station
CD/USB/SD/BT: During playback, press to search to the previous or next track
16. USB and SD CARD INPUT
17. TELESCOPIC ANTENNA
It should be extended to ensure a good FM reception.
7
REAR & BOTTOM
1.
2.
3.
4.
AUX
Connect to external audio player
HEADPHONE OUT JACK
Connect to the external headphone
AC IN ~
Connect the power cable to this jack
BATTERY COMPARTMENT DOOR
8
REMOTE CONTROL
1.
2.
3.
4.
5.
6.
7.
8.
STANDBY
NUMERIC BUTTONS
PRESET
10+
FOLDER +
RANDOM
REPEAT
BACKWARD
FORWARD
9. PROGRAM
10. PREVIOUS
NEXT
11. STOP
12. PLAY/PAUSE
13. TUNE+
14. TUNE15. PAIR
16. FM ST/MO
17. MUTE
18. VOL 19. VOL +
20. SOURCE
Remote Control Operation
A CR2025 battery is already installed in the remote control unit. Before using, pull out the battery insulation sheet as shown below.
9
To replace a new battery, please refer to the figure shown below. When inserting a battery, be sure to do so in the proper direction.






If the remote control conflicts with other devices, the operation will be affected.
Do not simultaneously press buttons on the unit and the remote control.
Avoid using two remote controls at the same time as it will cause a malfunction.
Use only CR-2025 size batteries.
If there is battery leakage, clean the remote control thoroughly before replacing batteries.
Do not short two terminals of the batteries. Dispose old batteries in a suitable place.
10
CONNECTING TO THE POWER SUPPLY
1.
2.
Connect the end of the detachable power cord to the unit rear panel AC IN ~ jack and the other end to the AC outlet.
Press the STANDBY button to turn on the unit.
Battery powered usage
For DC operation, firstly remove the AC plug from the AC outlet and disconnect the AC cord from the AC IN ~ jack. Then
insert 6 pcs size C (UM-2) batteries into the battery compartment.
Please note: Since the unit draws a little power from the batteries standby mode), remove the batteries if the unit is not
going to be used for a long time.
BASIC OPERATION
Press the STANDBY button to turn on the unit. To turn off, press the STANDBY button again.
FM/CD/USB/SD/BT/AUX
Press the SOURCE button to select different sources.
Volume Control
Press the VOL-/VOL+ buttons to change the volume.
Adjusting the Antenna
The telescopic antenna should be extended and altered to ensure a good FM reception.
FM RADIO OPERATION
Auto Scan
1. Turn on the unit and choose FM mode
2. Press and hold the TUNE- or TUNE+ Button to search for the next available radio station.
Manual Scan
Press the TUNE- or TUNE+ button repeatedly to tune for a different frequency.
Storing FM Presets
You can save up to 20 FM stations.
1. Tune to the station you wish to store.
2. Press the PROGRAM button. Preset channel number will be displayed.
3. Press the TUNE- or TUNE+ button to a preset number that you want to store. Then press the PROGRAM button to save.
11
Recall FM Presets
Press the PRESET button to recall the preset number station.
Stereo/Force Mono Selection
When receiving a stereo FM radio station, pressing, press the FM ST/MO button will switch between stereo audio or force mono
audio.
CD/USB/SD OPERATION
Loading and Playing CD Disc
Open the CD door. Install a disc with the CD graphic side facing up. Close the CD door. Press the SOURCE button to CD mode. After
reading the total number of tracks will be shown on the display. Press the PLAY/PAUSE
button to play.
Reading and Playing USB Device
Insert a USB device into the USB input jack. Press the SOURCE button to USB mode. After reading the total number of tracks will be
shown on the display. Press the PLAY/PAUSE
button to play.
Reading and Playing SD Card
Insert a SD card device into the SD card input jack. Press the SOURCE button to SD Card mode. After reading the total number of
tracks will be shown on the display. Press the PLAY/PAUSE
button to play.
Play/Pause Control
To pause playback press the PLAY/PAUSE
Stop Control
To stop playback press the STOP
button. Press the button again to resume playback.
button.
Skip Track
During playback press the PREVIOUS
or NEXT
button to search to the previous or next track.
Random Play
During playback press the RANDOM button to play music in random order. The display will show “RAND”. Press the RANDOM button
again to resume normal playback.
High-Speed Music Search
During playback press & hold the BACKWARD
or FORWARD
button to start high-speed searching. When you release the
BACKWARD
or FORWARD
button normal speed playback will resume.
Repeat Playing
During playback press the REPEAT button once, the current track will be played repeatedly. Press the REPEAT button again, all tracks
will be played repeatedly. Press the REPEAT button again to resume normal playback.
In case of MP3 file folder playback, there is a repeat folder as well.
Folder Up (MP3 file only)
During MP3 playback press the FOLDER + button on the remote control (or press and hold the FOLDER+ button on the unit) to search
to the next folder (folder up).
In stop mode press the FOLDER + button on the remote control (or press and hold the FOLDER+ button on the unit) to change the
folder. Then press the PREVIOUS
or NEXT
button to select your desired track to play. Press the PLAY/PAUSE
button to
start playback the track.
User Programmed Playback
This unit can be programmed to play any sequence of up to 20 tracks.
1. In stop mode press the PROGRAM button on the remote control. “P01” will be shown on the display.
2. Press the PREVIOUS
or NEXT
button to select the desired track.
3. Press the PROGRAM button to save the desired track.
4. Repeat steps 2-4 to program up to 20 tracks.
5. Press the PLAY/PAUSE
button to play according to the programmed track.
6. To clear program play press the STOP button twice or change to another mode.
7. During program play you can also do the repeat one or repeat all operation. But during program play, random play is not
supported.
12
BLUETOOTH CONNECTION
Please follow the pairing instructions below to link the unit to your Bluetooth device.
1. Press the SOURCE button repeatedly to enter the Bluetooth mode. The display will show “bt”. It will start searching and will keep
flashing.
2. If the unit has never been paired with a Bluetooth device before or cannot find the last paired device, the display and the
Bluetooth status indicator will keep on flashing. Turn on the Bluetooth function of your device and enable the search until “Lenco
SCD-100” is found. Select “Lenco SCD-100” on the Bluetooth device to make connection. Enter the pass code “0000” if required.
3. After successfully paired the unit will display steady “bt” without flashing.
4. You can now start playing music from your smartphone wirelessly to the speaker.
5. You can press the
button to pause or resume the playback.
6. You can press the PREVIOUS
or NEXT
button to search to the previous or next song.
 Press the PAIR button on the remote control (or press and hold the PAIR button on the unit) will disconnect the current
connection and start to search another new Bluetooth device
AUX IN
This allows you to connect an external player’s sound through your unit.
1. Plug a 3.5mm audio cable (not included) into your external player’s line out and the other end into the AUX jack.
2. Press the SOURCE button to enter AUX mode. Display shows “AU”
3. Start your external player to play music.
4. The unit will output the sound.
ENERGY SAVING
Due to ErP stage 2 requirement and protection of the environment, this unit will switch to standby mode automatically when no
music is played for about 15 minutes.
To reactivate the unit, press the STANDBY button again.
CLOCK SETUP
To set the time manually:
1.
2.
3.
4.
Turn off the unit to Standby mode.
Press and hold the PROGRAM button, the Hour digits will flash.
Press the PREVIOUS
or NEXT
button to change the hour value. Press the PROGRAM button to continue.
The Minute digits will flash. Press the PREVIOUS
or NEXT
button to change the minute value. Press the PROGRAM
button to complete the setup.
ACCESSORIES



Power cable x 1
Remote control x 1
Instruction manual x 1
13
TECHNICAL SPECIFICATIONS
FM radio frequency range
AC power input
Power consumption
Batteries Operation
Speaker output power
Bluetooth
USB
SD
Aux In
Headphone
Remote control battery
Dimension (L x D x H)
Weight


87.5-108 MHz
230V~, 50Hz
22 W
6 x UM2 (C Size)
2 x 5 W RMS
5.0 + EDR
V2.1
USB 2.0 type A socket
Full size SD card slot
3.5mm stereo jack
3.5mm stereo jack
CR2025 x 1pcs
372 x 273 x 160 mm
2.4 kg
The specification presents only as a reference. The value of weight and size are approximation.
Our product is improved ceaselessly and the specification and function may be changed without prior notice.
14
GUARANTEE
Lenco offers service and warranty in accordance to European law, which means that in case of repairs (both during and
after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer
will be voided.
DISCLAIMER
Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications
and pictures in this documentation may differ slightly from your particular situation. All items described in this guide for
illustration purposes only and may not apply to particular situation. No legal right or entitlements may be obtained from the
description made in this manual.
DISPOSAL OF THE OLD DEVICE
This symbol indicates that the relevant electrical product or battery should not be disposed of as
general household waste in Europe. To ensure the correct waste treatment of the product and battery,
please dispose them in accordance to any applicable local laws of requirement for disposal of
electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve
standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical
and Electronic Equipment Directive).
CE MARKING
Hereby, Lenco Benelux B.V., Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this product is in
compliance with the essential EU directive requirements.
The declaration of conformity may be consulted via [email protected]
SERVICE
For more information and helpdesk support, please visit www.lenco.com
Lenco Benelux BV, Thermiekstraat 1a, 6361 HB, The Netherlands.
15
">