Fig. 800 - Adjustable Sway Brace Attachment to Steel www.tolco.com

Fig. 800 - Adjustable Sway Brace Attachment to Steel www.tolco.com
www.tolco.com
Revision 1/21/2011
Fig. 800 - Adjustable Sway Brace Attachment to Steel
Size Range — 4" thru 18" beam width
Material — Carbon Steel
Function — Seismic brace attachment to steel.
Features — This product’s design incorporates a concentric attachment
point which is critical to the performance of structural seismic connections.
NFPA 13 indicates the importance of concentric loading of connections
and fasteners. Permits secure connection to steel where drilling and/or
welding of brace connection could present structural issues.
Installation Instructions — The Fig. 800 is the structural attachment component of a longitudinal or lateral sway brace assembly. It is intended to
be combined with a TOLCO transitional attachment, "bracing pipe" and a
TOLCO "braced pipe" attachment to form a complete bracing assembly.
NFPA 13 and/or OSHPD guidelines should be followed.
To Install — Place the Fig. 800 on the steel beam, tighten the cone point
set bolts on flange until bolt heads break off. Tighten hex head bolts into
clamp body until lock washers are fully flat. Attach other TOLCO transitional attachment fitting, Fig. 909, 910, 980 or 986. Transitional fitting
attachment can pivot for adjustment to proper brace angle.
Approvals — Underwriters Laboratories Listed in the USA (UL) and
Canada (cUL). Approved by Factory Mutual Engineering (FM). Included in
our Seismic Restraints Catalog approved by the State of California Office
of Statewide Health Planning and Development (OSHPD). For additional
load, spacing and placement information relating to OSHPD projects,
please refer to the TOLCO Seismic Restraint Systems Guidelines.
Finish — Plain
Note — Available in Electro-Galvanized and HDG finish.
Order By — Figure number, type number and size number.
Component of State of
California OSHPD Approved
Seismic Restraints System
Dimensions • Weights
Size
1
2
3
4
5
6
7
Max. Design Loads/Lbs. (cULus)
Max. Design Load Lbs. (FM)*
Fits Beam
Range (In.)
Along
Beam
Across
Beam
Along
Beam
Across
Beam
4 - 6
6 - 8
8 - 10
10 - 12
12 - 14
14 - 16
16 - 18
1265
1265
1265
1265
1265
1265
1265
2015
2015
2015
2015
2015
2015
2015
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
Dimensions • Weights
Max. Design Loads/Lbs. (cULus)
Flange Thickness
Type
Max. (In.)
1
2
3/4
11⁄4
Max. Design Load Lbs. (FM)*
Along
Beam
Across
Beam
Along
Beam
Across
Beam
1265
1265
2015
2015
2800
2800
2800
2800
* The loads listed are axial loads on the brace. The horizontal load capacity, H, of the
brace is: H = F x sin θ, where θ is the installation angle measured from the vertical.
TOLCO® brand bracing components are desgined to be compatible ONLY with other TOLCO® brand bracing components, resulting in a Listed
seismic bracing assembly. DISCLAIMER — NIBCO does NOT warrant against the failure of TOLCO® brand bracing components, in the instance
that such TOLCO® brand bracing components are used in combination with products, parts or systems which are not manufactured or sold under
the TOLCO® brand. NIBCO shall NOT be liable under any circumstance for any direct or indirect, incidental or consequential damages of any kind,
including but not limited to loss of business or profit, where non-TOLCO brand bracing components have been, or are used.
OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330
CUSTOMER SERVICE • 800.786.5266
www.tolco.com
142
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement