Armstrong HC-6700 Product data

Armstrong HC-6700 Product data
Paulson-Cheek Mechanical
6145 Northbelt Parkway
Suite F
Norcross, GA 30071
Ga. Reg. 000386
770. 729. 0076
770. 729. 1076 Fax
Northside Facial Cosmetic Surgery
Alpharetta, GA
HVAC Submittal
April 15, 2015
General Contractor:
D. C. Ecker Construction, Inc.
Mechanical Engineer:
AHA Consulting Engineers
Mechanical Contractor:
Paulson-Cheek Mechanical, Inc.
Section 1
Trane Split Systems
Section 2
Aaon Split Systems
Section 3
Humidifiers
Section 4
Grilles, Registers, & Diffusers
Section 5
Flexible Ductwork
Section 6
Spin-In Dampers, Saddle Fittings, & Line
Dampers
Section 7
Fire Dampers
Section 8
Motor Operated Dampers
Section 9
Wall Louvers
Section 10
Exhaust Fans
Section 11
Unit & Wall Heaters
HVAC Submittal Cover Sheet
SECTION: 1
PRODUCT: Trane Split Systems
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
Trane
Trane
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
Submittal
Prepared For:
Paulson Cheek Mechanical
Attn: Mark Walden
6145 Northbelt Parkway
Norcross, GA 30071
Sold To:
Paulson Cheek Mechanical
April 13,20,
2015
Date: March
2015
Job Name:
Northside Facial Cosmetic Surgery Alpharetta GA
Trane U.S. Inc. is pleased to provide the enclosed submittal for your review and approval.
Product Summary
Qty
Product
7
Split System Air Conditioning Units (Small)
Split System Notes:
1. Disconnect switches, auxiliary drain pans, fire/smoke devices, thermostats, external isolation,
refrigerant line sets and specialties, spare filters and belts, start up and first year labor warranty are not
included by Trane
2. (Fld)=provided by Trane, field installed by others
Sincerely,
The attached information describes the equipment we propose to
furnish for this project, and is submitted for your approval.
Becky Warner Sanborn, LEED AP
Account Manager
Trane U.S. Inc. - Ingersoll Rand
Office: 678-775-4202
Cell: 404-226-6954
Email: [email protected]
www.trane.com
J:\JOBS\38\218739\2\Northside Facial Cosmetic Surgery Alpharetta GA Split System Submittal 3-20-15.doc
Table Of Contents
Product Summary .......................................................................................................................... 1
Split System Air Conditioning Units (Small) (Items A1 - A3)..................................................... 3
Tag Data ................................................................................................................................................... 3
Product Data ............................................................................................................................................ 3
Mechanical Specifications ..................................................................................................................... 7
Unit Dimensions ....................................................................................................................................... 9
Weight, Clearance & Rigging Diagram ................................................................................................... 21
Accessory ............................................................................................................................................... 22
Field Installed Options - Part/Order Number Summary ........................................................... 23
Split System Air Conditioning Units (Small) ............................................................................................ 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Tag Data - Split System Air Conditioning Units (Small) (Qty: 7)
Item Tag(s)
Qty Description
Model Number
A1
FCU/CU-1-1,
3
4 Ton Split A/C
4TTR4048L1000-GAM5B0C48MFCU/CU-1-2,
FCU/CU-2-1
A2
FCU/CU-2-2,
2
3 Ton Split A/C
4TTR4036L1000-GAM5B0C42MFCU/CU-2-3
A3
FCU/CU-2-4,
2
2 Ton Split A/C
4TTR4024L1000-GAM5B0B30MFCU/CU-2-5
Product Data - Split System Air Conditioning Units (Small)
Item: A1 Qty: 3 Tag(s): FCU/CU-1-1, FCU/CU-1-2, FCU/CU-2-1
Split System Cooling Outdoor Unit
4 Ton Nominal Cooling Capacity
200 - 230 Volt 1 Phase 60 Hertz
4 Ton air handler
Programmable 7 day , 3 heat/2 cool thermostat (Fld)
Evaporator defrost control (Fld)
Crankcase heater kit (Fld)
10.80/14.40 kW Htr w/Ckt Brk 208/240/1 (Fld)
Single point entry kit (Fld)
Item: A2 Qty: 2 Tag(s): FCU/CU-2-2, FCU/CU-2-3
Split System Cooling Outdoor Unit
3 Ton Nominal Cooling Capacity
200 - 230 Volt 1 Phase 60 Hertz
3.5 Ton air handler
Programmable 7 day , 3 heat/2 cool thermostat (Fld)
Evaporator defrost control (Fld)
Crankcase heater kit (Fld)
7.21/9.60 kW Electric Htr w/Ckt Brk for 208/240V 1 Phase 60 Hz (Fld)
Item: A3 Qty: 2 Tag(s): FCU/CU-2-4, FCU/CU-2-5
Split System Cooling Outdoor Unit
2 Ton Nominal Cooling Capacity
200 - 230 Volt 1 Phase 60 Hertz
2.5 Ton air handler
Programmable 7 day , 3 heat/2 cool thermostat (Fld)
Evaporator defrost control (Fld)
Crankcase heater kit (Fld)
5.77/7.68 kW Electric Htr w/ Ckt Brk for 208/240V 1 Phase 60 Hz (Fld)
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 3 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Performance Data:
FCU-1-1,1-2,2-1
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 4 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
FCU-2-2,2-3
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 5 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
FCU-2-4,2-5
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 6 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Mechanical Specifications - Split System Air Conditioning Units (Small)
Item: A1 - A3 Qty: 7 Tag(s): FCU/CU-1-1, FCU/CU-1-2, FCU/CU-2-1, FCU/CU-2-2, FCU/CU-2-3, FCU/CU-2-4, FCU/CU-2-5
GAM5
Air-Tite II cabinet
2% or less air leakage
Precision applied - durable door seals
Specially designed air seal around refrigerant,
condensate and conduit connections
Double wall foamed cabinet system
R-4.2 insulating value
No loose fiber design
Smooth cleanable interior design
Sweat eliminating design
Composite foamed cabinet doors
Water proof cabinet design
Integrated horizontal drain pans
Modular cabinet with " allen wrench "quick latch" design
Multi-position up/down flow horizontal left/right
Side return option
Control board protection pocket built into cabinet wall
Alert port to view control board codes without door removal
10 alert codes
Low voltage terminal connection point
Quarter turn phillips head door fasteners
Vortica blower with polarized plug connections and integrated slide deck for easy removal
Patented enhanced coil fin
Dual refrigerant compatible as shipped
Slide in electric heaters with polarized plug connections (sold as accessory)
UVC light kit with safety switch and polarized plug connections (sold as accessory)
Labeled panels and connections
Molded in 1" standard filter rail
High efficiency ECM motor
Soft start fan motor operation
Built in fan delay modes
Maximum width of 23 1/2"
Compact 20 13/16" depth with doors removed
Two tone color
Fused 24v power
Safety door switch
1-year warranty
10-year warranty registered
Optional extended warranty available
Heater Section - 1 Phase Vertical Air Handler
A compartment is provided in the blower section for field installation of supplementary heater. Polarized plugs are
provided for making electrical connections to the air handler control box from the supplementary heater.
4TTR4 - General
The Outdoor Units are fully charged from the factory for up to 15 feet of piping. This unit is designed to operate at
outdoor ambient temperatures as high as 115F. Cooling capacities are matched with a wide selection of air handlers
and furnace coils that are AHRI certified. The unit is certified to UL 1995. Exterior is designed for outdoor application.
4TTR4 - Casing
Unit casing is constructed of heavy gauge, G60 galvanized steel and painted with a weather resistant powder paint on
all louvered panels and prepaint on all other panels. Corrosion and weatherproof CMBP-G30 base.
4TTR4 - Refrigerant Controls
Refrigeration system controls include condenser fan, compressor contactor and high pressure switch. High and low
pressure controls are inherent to the compressor. A factory supplied liquid line drier is standard. Some models may
require field installation.
4TTR4 - Compressor
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 7 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
The compressor features internal over temperature, pressure protection and total dipped hermetic motor. Other features
include: Centrifugal oil pump and low vibration and noise.
4TTR4 - Condenser Coil
The outdoor coil provides low airflow resistance and efficient heat transfer. The coil is protected on all four sides by
louvered panels.
4TTR4 - Low Ambient Cooling
As manufactured, this system has a cooling capacity to 55F. The addition of an evaporator defrost control permits
operation to 40F. The addition of an evaporator defrost control with TXV permits low ambient cooling to 30F.
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 8 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A1 Qty: 3 Tag(s): FCU/CU-1-1, FCU/CU-1-2, FCU/CU-2-1
NOTES:
1. BADGE ROTATION WILL KEEP BRAND IN CORRECT POSITION.
2. NO INTERNAL MODIFICATIONS REQUIRED FOR ANY POSITION.
3. VERIFY WEIGHT, CONNECTION, AND ALL DIMENSION WITH
INSTALLER DOCUMENTS BEFORE INSTALLATION
4. GAM5 AIR HANDLERS ARE ALL TWO PIECE CABINETS.
5. SEE WEIGHT AND RIGGING PAGE FOR CONDENSATE DRAIN
CONFIGURATION
21 3/4"
14 3/8"
1 1/2"
23 1/2"
5 15/16"
20 1/2"
1 1/2"
10 5/16"
3"
3/8" LIQUID LINE
7/8" GAS LINE
SEE NOTE 1
CONDENSATE DRAIN
61 11/16"
1 1/2"
51 1/2"
24 7/8"
21 13/16"
17 1/8"
1 1/2"
1 1/2"
3 3/16"
20 1/2"
GAM5A0A48 & 60 AIR HANDLER
UNIT DIMENSION DRAWING
1 1/2"
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 9 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A1 Qty: 3 Tag(s): FCU/CU-1-1, FCU/CU-1-2, FCU/CU-2-1
ELECTRICAL / GENERAL DATA
GENERAL
(1)(2)(4)
INDOOR MOTOR
Model:
GAM5A0C48M41SA
Unit Primary Voltage:
Unit Secondary Voltage:
Unit Hertz:
Unit Phase:
208
230
60
1
STANDARD
(5)
8.0/8.0
15.0/15.0
ELECTRIC HEAT
# of Circuit:
Phase:
1
0.75
1050
1
6.0
Type:
REF. Line Connections
Coupling or Conn. Size - Gas:
Coupling or Conn. Size - Liq.:
(3)
Type:
Furnished:
Number:
Recommended:
Throwaway
No
1
22"x20"x1"
Weights
R410
Brazed
7/8"
3/8"
Net:
Shipping:
166.0 lb
176.0 lb
NOTES:
230 Volt / 208 Volt
Capacity Circuit #1:
Capacity Circuit #2:
Capacity Circuit #3:
Number:
Horsepower:
Motor Speed (RPM):
Phase:
Full Load Amps:
Locked Rotor Amps:
FILTERS
REFRIGERANT
230 Volt / 208 Volt
Minimum Circuit Ampacity:
Maximum Overload Protection:
(1)
9.60/7.20
4.80/3.60
N/A
2
1
Heater Amps Per Circuit Circuit #1:
Heater Amps Per Circuit Circuit #2:
Heater Amps Per Circuit Circuit #3:
40.0/34.6
20.0/17.3
N/A
Minimum Circuit Ampacity Circuit #1:
Minimum Circuit Ampacity Circuit #2:
Minimum Circuit Ampacity Circuit #3:
58.0/51.0
25.0/22.0
N/A
Maximum Overload Protection Circuit #1:
Maximum Overload Protection Circuit #2:
Maximum Overload Protection Circuit #3:
60.0/60.0
25.0/25.0
N/A
1. These air handlers are a.r.i. certified with various split system air conditioners and heat pumps
(ari standard 210/240). refer tothesplit system outdoor unit product data guides for performance data.
2. 3/4" male plastic pipe (ref.: astm 1785-76)
3. Minimum filter size for horizontal applications will be based on airflow selection
and will be calculated as follows:
low velocity filter: face area (sq. ft.) = cfm / 300
high velocity filter: face area (sq. ft.) = cfm / 500
4. For customer ease of filter maintenance, it is recommended that a properly sized, remote filter and grille be
installed for horizontal applications. airflow should not exceed the face value of the filter being used
5. Standard mca and mop without electric heat.
Correct Single Point Electrical, with single point
connection kit (fld):
Voltage 208/1
Elec Heat 10.8kw
FLA 51.9a
MCA 74a
MOP 80a
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 10 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A1 Qty: 3 Tag(s): FCU/CU-1-1, FCU/CU-1-2, FCU/CU-2-1
NOTES
1. TOP DISCHARGE AREA SHOULD BE
UNRESTRICTED FOR AT LEAST 60"
ABOVE UNIT. UNIT SHOULD BE PLACED SO ROOF
RUN-OFF WATER DOES NOT POUR DIRECTLY ON UNIT,
AND SHOULD BE AT LEAST 12" FROM WALL AND
ALL SURROUNDING SHRUBBERY ON TWO SIDES.
OTHER TWO SIDES UNRESTRICTED.
2. ELECTRICAL AND REFRIGERANT COMPONENT
CLEARANCES PER PREVAILING CODES.
37 1/4"
SERVICE PANEL
SEE NOTE 2
34 1/4"
1"
ELECTRICAL
SERVICE PANEL
7/8" DIA. HOLE
LOW VOLTAGE
20"
29 1/8"
1 1/8" DIA. K.O. WITH
7/8" DIA. HOLE IN CONTROL
BOX BOTTOM FOR
ELECTRICAL POWER SUPPLY
1"
8 1/8"
LIQUID LINE SERVICE VALVE,
3/8" I.D. FEMALE BRAZE
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
8 1/8"
5 5/8"
2 3/4"
3 1/4"
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
LIQUID LINE SERVICE VALVE,
3/8" I.D. FEMALE BRAZE
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
GAS LINE 1/4" TURN BALL
SERVICE VALVE, 7/8" I.D. FEMALE
BRAZED CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
Equipment Submittal
5 5/8"
2 3/4"
3 1/4"
GAS LINE SERVICE VALVE,
7/8" I.D. FEMALE BRAZED
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
Page 11 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A1 Qty: 3 Tag(s): FCU/CU-1-1, FCU/CU-1-2, FCU/CU-2-1
ELECTRICAL / GENERAL DATA
GENERAL
POWER CONN.
Model:
Voltage:
Unit Hertz:
Unit Phase:
Minimum Circuit Ampacity:
Maximum Circuit Breaker:
Minimum Protection Rating:
1
0.20
1
0.95
-
1. Certified in accordance with the Unitary Air-Conditioner equipment certification program which is based on
AHRI Standard 210/240.
2. Calculated in accordance with N.E.C. Use only HACR circuit breakers or fuses.
3. Standard line lengths - 60'. Standard lift - 60' Suction and Liquid line.
For Greater lengths and lifts refer to refrigerant piping software Pub# 32-3312-0
4. * = 15, 20, 25, 30, 40 and 50 foot lineset available.
OUTDOOR MOTOR
Number:
Horsepower:
Motor Speed (RPM):
Phase:
Full Load Amps:
Locked Rotor Amps:
COMPRESSOR
4TTR4048
208 - 230
60
1
24.0
40.0
40.0
Number:
Phase:
Rated Load Amps:
Locked Rotor Amps:
1
1
18.5
124.0
NOTES:
REFRIGERANT
Type:
Charge:
Line Size O.D. Gas:
Line Size O.D. LIQ:
R-410
6.6 lb
7/8"
3/8"
C1
WEIGHT
189.0 lb
212.0 lb
DISCHARGE
NET
SHIPPING
NOTES:
C1. TOP DISCHARGE SHOULD BE UNRESTRICTED
FOR AT LEAST 60" ABOVE UNIT
C2. PLACE UNIT FROM WALL
C3. PLACE SHRUBBERY AT LEAST 12"
FROM UNIT ON TWO SIDES, OTHER SIDES
UNRESTRICTED
C4. PLACE UNIT SO ROOF RUN-OFF DOES NOT
FALL DIRECTLY ON UNIT
C4
C3
C2
C3
WEIGHT AND CLEARANCE
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 12 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A2 Qty: 2 Tag(s): FCU/CU-2-2, FCU/CU-2-3
NOTES:
1. BADGE ROTATION WILL KEEP BRAND IN CORRECT POSITION.
2. NO INTERNAL MODIFICATIONS REQUIRED FOR ANY POSITION.
3. VERIFY WEIGHT, CONNECTION, AND ALL DIMENSION WITH
INSTALLER DOCUMENTS BEFORE INSTALLATION
4. GAM5 AIR HANDLERS ARE ALL TWO PIECE CABINETS.
5. SEE WEIGHT AND RIGGING PAGE FOR CONDENSATE DRAIN
CONFIGURATION
21 3/4"
14 3/8"
1 1/2"
23 1/2"
5 15/16"
20 1/2"
10 5/16"
1 1/2"
3"
3/8" LIQUID LINE
7/8" GAS LINE
SEE NOTE 1
CONDENSATE DRAIN
56 7/8"
1 1/2"
46 11/16"
24 1/2"
21 13/16"
17 1/8"
1 1/2"
1 1/2"
3 3/16"
20 1/2"
GAM5A0A42 AIR HANDLER
UNIT DIMENSION DRAWING
1 1/2"
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 13 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A2 Qty: 2 Tag(s): FCU/CU-2-2, FCU/CU-2-3
ELECTRICAL / GENERAL DATA
GENERAL
(1)(2)(4)
INDOOR MOTOR
Model:
GAM5A0C42M31SA
Unit Primary Voltage:
Unit Secondary Voltage:
Unit Hertz:
Unit Phase:
208
230
60
1
STANDARD
(5)
5.0/5.0
15.0/15.0
ELECTRIC HEAT
# of Circuit:
Phase:
1
0.5
1050
1
4.1
Type:
REF. Line Connections
Coupling or Conn. Size - Gas:
Coupling or Conn. Size - Liq.:
(3)
Type:
Furnished:
Number:
Recommended:
Throwaway
No
1
22"x20"x1"
Weights
R410
Brazed
7/8"
3/8"
Net:
Shipping:
153.0 lb
163.0 lb
NOTES:
230 Volt / 208 Volt
Capacity Circuit #1:
Capacity Circuit #2:
Capacity Circuit #3:
Number:
Horsepower:
Motor Speed (RPM):
Phase:
Full Load Amps:
Locked Rotor Amps:
FILTERS
REFRIGERANT
230 Volt / 208 Volt
Minimum Circuit Ampacity:
Maximum Overload Protection:
(1)
9.60kW/7.20kW
N/A
N/A
1
1
Heater Amps Per Circuit Circuit #1:
Heater Amps Per Circuit Circuit #2:
Heater Amps Per Circuit Circuit #3:
40.0/34.60
N/A
N/A
Minimum Circuit Ampacity Circuit #1:
Minimum Circuit Ampacity Circuit #2:
Minimum Circuit Ampacity Circuit #3:
55.0/48.0
N/A
N/A
Maximum Overload Protection Circuit #1:
Maximum Overload Protection Circuit #2:
Maximum Overload Protection Circuit #3:
60.0/50.0
N/A
N/A
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
1. These air handlers are a.r.i. certified with various split system air conditioners and heat pumps
(ari standard 210/240). refer tothesplit system outdoor unit product data guides for performance data.
2. 3/4" male plastic pipe (ref.: astm 1785-76)
3. Minimum filter size for horizontal applications will be based on airflow selection
and will be calculated as follows:
low velocity filter: face area (sq. ft.) = cfm / 300
high velocity filter: face area (sq. ft.) = cfm / 500
4. For customer ease of filter maintenance, it is recommended that a properly sized, remote filter and grille be
installed for horizontal applications. airflow should not exceed the face value of the filter being used
5. Standard mca and mop without electric heat.
Equipment Submittal
Page 14 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A2 Qty: 2 Tag(s): FCU/CU-2-2, FCU/CU-2-3
32 5/8"
SERVICE PANEL
SEE NOTE 2
29 3/4"
NOTES
1. TOP DISCHARGE AREA SHOULD BE
UNRESTRICTED FOR AT LEAST 60"
ABOVE UNIT. UNIT SHOULD BE PLACED SO ROOF
RUN-OFF WATER DOES NOT POUR DIRECTLY ON UNIT,
AND SHOULD BE AT LEAST 12" FROM WALL AND
ALL SURROUNDING SHRUBBERY ON TWO SIDES.
OTHER TWO SIDES UNRESTRICTED.
2. ELECTRICAL AND REFRIGERANT COMPONENT
CLEARANCES PER PREVAILING CODES.
1"
ELECTRICAL
SERVICE PANEL
7/8" DIA. HOLE
LOW VOLTAGE
20"
32 3/4"
1 1/8" DIA. K.O. WITH
7/8" DIA. HOLE IN CONTROL
BOX BOTTOM FOR
ELECTRICAL POWER SUPPLY
1"
7 3/4"
LIQUID LINE SERVICE VALVE,
3/8" I.D. FEMALE BRAZE
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
LIQUID LINE SERVICE VALVE,
3/8" I.D. FEMALE BRAZE
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
7 3/4"
5"
2 3/8"
3"
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
GAS LINE 1/4" TURN BALL
SERVICE VALVE, 3/4" I.D. FEMALE
BRAZED CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
Equipment Submittal
5"
2 3/8"
3"
GAS LINE SERVICE VALVE,
3/4" I.D. FEMALE BRAZED
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
Page 15 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A2 Qty: 2 Tag(s): FCU/CU-2-2, FCU/CU-2-3
ELECTRICAL / GENERAL DATA
GENERAL
POWER CONN.
Model:
Voltage:
Unit Hertz:
Unit Phase:
Minimum Circuit Ampacity:
Maximum Circuit Breaker:
Minimum Protection Rating:
1
0.125
1
0.64
-
1. Certified in accordance with the Unitary Air-Conditioner equipment certification program which is based on
AHRI Standard 210/240.
2. Calculated in accordance with N.E.C. Use only HACR circuit breakers or fuses.
3. Standard line lengths - 60'. Standard lift - 60' Suction and Liquid line.
For Greater lengths and lifts refer to refrigerant piping software Pub# 32-3312-0
4. * = 15, 20, 25, 30, 40 and 50 foot lineset available.
OUTDOOR MOTOR
Number:
Horsepower:
Motor Speed (RPM):
Phase:
Full Load Amps:
Locked Rotor Amps:
COMPRESSOR
4TTR4036
208 - 230
60
1
18.0
30.0
30.0
Number:
Phase:
Rated Load Amps:
Locked Rotor Amps:
1
1
14.1
72.0
NOTES:
REFRIGERANT
Type:
Charge:
Line Size O.D. Gas:
Line Size O.D. LIQ:
R-410
6.1 lb
3/4"
3/8"
C1
WEIGHT
156.0 lb
183.0 lb
DISCHARGE
NET
SHIPPING
NOTES:
C1. TOP DISCHARGE SHOULD BE UNRESTRICTED
FOR AT LEAST 60" ABOVE UNIT
C2. PLACE UNIT FROM WALL
C3. PLACE SHRUBBERY AT LEAST 12"
FROM UNIT ON TWO SIDES, OTHER SIDES
UNRESTRICTED
C4. PLACE UNIT SO ROOF RUN-OFF DOES NOT
FALL DIRECTLY ON UNIT
C4
C3
C2
C3
WEIGHT AND CLEARANCE
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 16 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A3 Qty: 2 Tag(s): FCU/CU-2-4, FCU/CU-2-5
NOTES:
1. BADGE ROTATION WILL KEEP BRAND IN CORRECT POSITION.
2. NO INTERNAL MODIFICATIONS REQUIRED FOR ANY POSITION.
3. VERIFY WEIGHT, CONNECTION, AND ALL DIMENSION WITH
INSTALLER DOCUMENTS BEFORE INSTALLATION
4. GAM5 AIR HANDLERS ARE ALL TWO PIECE CABINETS.
5. SEE WEIGHT AND RIGGING PAGE FOR CONDENSATE DRAIN
CONFIGURATION
21 3/4"
14 3/8"
1 1/2"
21 5/16"
5 15/16"
18 3/8"
1 1/2"
9 3/16"
3"
3/8" LIQUID LINE
3/4" GAS LINE
SEE NOTE 1
CONDENSATE DRAIN
51 1/2"
1 1/2"
41 3/16"
24 13/16"
21 13/16"
17 1/8"
1 1/2"
1 1/2"
18 3/8"
3 3/16"
GAM5A0A30 AIR HANDLER
UNIT DIMENSION DRAWING
1 1/2"
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 17 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A3 Qty: 2 Tag(s): FCU/CU-2-4, FCU/CU-2-5
ELECTRICAL / GENERAL DATA
GENERAL
(1)(2)(4)
INDOOR MOTOR
Model:
GAM5A0B30M21SA
Unit Primary Voltage:
Unit Secondary Voltage:
Unit Hertz:
Unit Phase:
208
230
60
1
STANDARD
(5)
4.0/4.0
15.0/15.0
ELECTRIC HEAT
# of Circuit:
Phase:
1
0.33
1050
1
2.8
-
Type:
REF. Line Connections
Coupling or Conn. Size - Gas:
Coupling or Conn. Size - Liq.:
(3)
Type:
Furnished:
Number:
Recommended:
Throwaway
No
1
20"x20"x1"
Weights
R410
Brazed
3/4"
3/8"
Net:
Shipping:
132.0 lb
140.0 lb
NOTES:
230 Volt / 208 Volt
Capacity Circuit #1:
Capacity Circuit #2:
Capacity Circuit #3:
Number:
Horsepower:
Motor Speed (RPM):
Phase:
Full Load Amps:
Locked Rotor Amps:
FILTERS
REFRIGERANT
230 Volt / 208 Volt
Minimum Circuit Ampacity:
Maximum Overload Protection:
(1)
7.68kW/5.76kW
N/A
N/A
1
1
Heater Amps Per Circuit Circuit #1:
Heater Amps Per Circuit Circuit #2:
Heater Amps Per Circuit Circuit #3:
32.0/27.70
N/A
N/A
Minimum Circuit Ampacity Circuit #1:
Minimum Circuit Ampacity Circuit #2:
Minimum Circuit Ampacity Circuit #3:
44.0/38.0
N/A
N/A
Maximum Overload Protection Circuit #1:
Maximum Overload Protection Circuit #2:
Maximum Overload Protection Circuit #3:
45.0/40.0
N/A
N/A
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
1. These air handlers are a.r.i. certified with various split system air conditioners and heat pumps
(ari standard 210/240). refer tothesplit system outdoor unit product data guides for performance data.
2. 3/4" male plastic pipe (ref.: astm 1785-76)
3. Minimum filter size for horizontal applications will be based on airflow selection
and will be calculated as follows:
low velocity filter: face area (sq. ft.) = cfm / 300
high velocity filter: face area (sq. ft.) = cfm / 500
4. For customer ease of filter maintenance, it is recommended that a properly sized, remote filter and grille be
installed for horizontal applications. airflow should not exceed the face value of the filter being used
5. Standard mca and mop without electric heat.
Equipment Submittal
Page 18 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A3 Qty: 2 Tag(s): FCU/CU-2-4, FCU/CU-2-5
NOTES
1. TOP DISCHARGE AREA SHOULD BE
UNRESTRICTED FOR AT LEAST 60"
ABOVE UNIT. UNIT SHOULD BE PLACED SO ROOF
RUN-OFF WATER DOES NOT POUR DIRECTLY ON UNIT,
AND SHOULD BE AT LEAST 12" FROM WALL AND
ALL SURROUNDING SHRUBBERY ON TWO SIDES.
OTHER TWO SIDES UNRESTRICTED.
2. ELECTRICAL AND REFRIGERANT COMPONENT
CLEARANCES PER PREVAILING CODES.
28 1/2"
SERVICE PANEL
SEE NOTE 2
25 5/8"
1"
ELECTRICAL
SERVICE PANEL
7/8" DIA. HOLE
LOW VOLTAGE
18"
28 3/4"
1 1/8" DIA. K.O. WITH
7/8" DIA. HOLE IN CONTROL
BOX BOTTOM FOR
ELECTRICAL POWER SUPPLY
1"
7 5/8"
LIQUID LINE SERVICE VALVE,
3/8" I.D. FEMALE BRAZE
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
LIQUID LINE SERVICE VALVE,
3/8" I.D. FEMALE BRAZE
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
7 5/8"
5"
1 1/2"
2 1/4"
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
GAS LINE 1/4" TURN BALL
SERVICE VALVE, 3/4" I.D. FEMALE
BRAZED CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
Equipment Submittal
5"
1 1/2"
2 1/4"
GAS LINE SERVICE VALVE,
3/4" I.D. FEMALE BRAZED
CONNECTION WITH 1/4" SAE
FLARE PRESSURE TAP FITTING.
Page 19 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Unit Dimensions - Split System Air Conditioning Units (Small)
Item: A3 Qty: 2 Tag(s): FCU/CU-2-4, FCU/CU-2-5
ELECTRICAL / GENERAL DATA
GENERAL
POWER CONN.
Model:
Voltage:
Unit Hertz:
Unit Phase:
Minimum Circuit Ampacity:
Maximum Circuit Breaker:
Minimum Protection Rating:
1
0.06
1
0.60
-
1. Certified in accordance with the Unitary Air-Conditioner equipment certification program which is based on
AHRI Standard 210/240.
2. Calculated in accordance with N.E.C. Use only HACR circuit breakers or fuses.
3. Standard line lengths - 60'. Standard lift - 60' Suction and Liquid line.
For Greater lengths and lifts refer to refrigerant piping software Pub# 32-3312-0
4. * = 15, 20, 25, 30, 40 and 50 foot lineset available.
OUTDOOR MOTOR
Number:
Horsepower:
Motor Speed (RPM):
Phase:
Full Load Amps:
Locked Rotor Amps:
COMPRESSOR
4TTR4024
208 - 230
60
1
14.0
25.0
25.0
Number:
Phase:
Rated Load Amps:
Locked Rotor Amps:
1
1
10.9
63.0
NOTES:
REFRIGERANT
Type:
Charge:
Line Size O.D. Gas:
Line Size O.D. LIQ:
R-410
4.7 lb
3/4"
3/8"
C1
WEIGHT
133.0 lb
153.0 lb
DISCHARGE
NET
SHIPPING
NOTES:
C1. TOP DISCHARGE SHOULD BE UNRESTRICTED
FOR AT LEAST 60" ABOVE UNIT
C2. PLACE UNIT FROM WALL
C3. PLACE SHRUBBERY AT LEAST 12"
FROM UNIT ON TWO SIDES, OTHER SIDES
UNRESTRICTED
C4. PLACE UNIT SO ROOF RUN-OFF DOES NOT
FALL DIRECTLY ON UNIT
C4
C3
C2
C3
WEIGHT AND CLEARANCE
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 20 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Weight, Clearance & Rigging Diagram - Split System Air Conditioning Units (Small)
Item: A1 - A3 Qty: 7 Tag(s): FCU/CU-1-1, FCU/CU-1-2, FCU/CU-2-1, FCU/CU-2-2, FCU/CU-2-3, FCU/CU-2-4,
FCU/CU-2-5
VERTICAL DOWNFLOW
REFRIGERANT
CONNECTION
DOWNFLOW
CONDENSATE
DRAIN
REFRIGERANT CONNECTION
DOWNFLOW CONDENSATE DRAIN
REFRIGERANT CONNECTION
VERTICAL UPFLOW
REFRIGERANT CONNECTION
HORIZONTAL LEFT FLOW
DOWNFLOW CONDENSATE DRAIN
HORIZONTAL RIGHT FLOW
DOWNFLOW CONDENSATE DRAIN
NOTES
1. NO INTERNAL MODIFICATIONS REQUIRED FOR ANY POSITION.
2. BADGE ROTATION WILL BRAND IN CORRECT POSITION.
MINIMUM UNIT CLEARANCE TABLE
TO COMBUSTIBLE
MATERIALS (REQUIRED)
SIDE
FRONT
BACK
INLET DUCT
OUTLET DUCT
SERVICE CLEARANCE
(RECOMMENDED)
0
0
0
0
0
2"
21"
0
0
0
CLEARANCE NOTES:
* 1" FOR THE FIRST 3 FT. OF OUTLET DUCT
WHEN ELECTRIC HEATERS ARE INSTALED EXCEPT
MODELS BAYHTR1405, 1408, AND 1410 ARE APPROVED FOR
0" PLEMUM AND DUCT CLEARANCE IN THE UPFLOW
CONFIGURATION ONLY ON TWE-P MODELS.
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 21 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Accessory - Split System Air Conditioning Units (Small)
Item: A1 - A3 Qty: 7 Tag(s): FCU/CU-1-1, FCU/CU-1-2, FCU/CU-2-1, FCU/CU-2-2, FCU/CU-2-3, FCU/CU-2-4,
FCU/CU-2-5
6"
1 3/8"
4 5/8"
3 5/16"
3 5/16"
TCONT200
ACCESSORY - THERMOSTAT
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Equipment Submittal
Page 22 of 23
Northside Facial Cosmetic Surgery Alpharetta GA
March 20, 2015
Field Installed Options - Part/Order Number Summary
This is a report to help you locate field installed options that arrive at the jobsite. This report provides part or order
numbers for each field installed option, and references it to a specific product tag. It is NOT intended as a bill of
material for the job.
Product Family - Split System Air Conditioning Units (Small)
Item Tag(s)
Qty Description
A1
FCU/CU-1-1,
3
4 Ton Split A/C
FCU/CU-1-2,
FCU/CU-2-1
Field Installed Option Description
Programmable 7 day , 3 heat/2 cool thermostat
Evaporator defrost control
Crankcase heater kit
Single point entry kit
10.80/14.40 kW Htr w/Ckt Brk 208/240/1
Item
A2
Tag(s)
FCU/CU-2-2,
FCU/CU-2-3
Part/Ordering Number
TCONT802AS32DA
AY28X079
BAYCCHT301
BAYSPEKT200A
BAYEABC15BK1BA
Qty Description
2
3 Ton Split A/C
Field Installed Option Description
7.21/9.60 kW Electric Htr w/Ckt Brk for 208/240V 1 Phase 60 Hz
Programmable 7 day , 3 heat/2 cool thermostat
Evaporator defrost control
Crankcase heater kit
Item
A3
Tag(s)
FCU/CU-2-4,
FCU/CU-2-5
Qty Description
2
2 Ton Split A/C
Field Installed Option Description
Programmable 7 day , 3 heat/2 cool thermostat
Evaporator defrost control
Crankcase heater kit
5.77/7.68 kW Electric Htr w/ Ckt Brk for 208/240V 1 Phase 60 Hz
FLD = Furnished by Trane U.S. Inc. / Installed by
Others
Model Number
4TTR4048L1000GAM5B0C48M-1S
-0----000-0--0
Equipment Submittal
Model Number
4TTR4036L1000GAM5B0000M-1S0----000-0--0
Part/Ordering Number
BAYEAAC10BK1BA
TCONT802AS32DA
AY28X079
BAYCCHT302
Model Number
4TTR4024L1000GAM5B0B30M-1S0----000-0--0
Part/Ordering Number
TCONT802AS32DA
AY28X079
BAYCCHT302
BAYEAAC08BK1BA
Page 23 of 23
HVAC Submittal Cover Sheet
SECTION: 2
PRODUCT: Aaon Split Systems
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
Aaon
Hill Co
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
P.O. Box 699
Roswell, Georgia 30077
Contractor Reg. No. CN003050
770-751-0850
770-751-0070 Facsimile
www.hillcompany.com
BBB
SUBMITTAL
FOR
Split Systems FCU-1-3, FCU-1-4
Project:
Northside Facial Cosmetic Surgery
Alpharetta, GA
Mechanical Contractor
Paulson-Cheek Mechanical
6145 Northbelt Parkway
Norcross, GA 30071
Mechanical Engineer
AHA Consulting Engineers
1801 Old Alabama Road, Suite 125
Roswell, GA 30076
SUBMITTED BY:
HILL COMPANY, INC.
1305 Old Ellis Rd.
Roswell, GA 30076
[email protected]
Phone: 770 480-2328
www.hillcompany.com
March 17, 2015
industrial • institutional • commercial
TABLE OF CONTENTS
I.
Notes, Clarifications, and Deviations
II.
Specifications
III. Performance
IV. Selected Options
V.
Drawings
VI. Field Piping
VII. Controls
Notes, Clarifications, and Deviations
Notes, Clarifications, and Deviations to Specifications & Schedule
•
•
•
•
•
•
Contractor to verify voltage. Units are submitted with 208/1/60.
Contractor to verify refrigerant line lengths and elbow quantities to allow for
correct line sizing.
Contractor to verify handing of unit for line connections.
FCU fan will be provided with EC motor to be used for balancing. The units
will run at constant speed per the drawings/specifications.
Mechanical contractor is responsible for mounting and wiring of control panel
and loose sensors.
Lead times are currently 9 weeks.
industrial • institutional • commercial
Specifications
Guide Specifications - Air Handling Units FCU-1-3 and FCU-1-4
Part 1 - General
1.01 General Description
A.
This section includes the design, controls, and installation requirements for indoor air
handling units.
1.02 Quality Assurance
A.
Unit shall be certified in accordance with UL Standard 1995/CSA C22.2 No. 236,
Safety Standard for Heating and Cooling Equipment.
B.
Unit and refrigeration system shall comply with ASHRAE 15, Safety Standard for
Mechanical Refrigeration.
C.
Unit Seasonal Energy Efficiency Ratio (SEER) shall be equal to or greater that
prescribed by ASHRAE 90.1, Energy Efficient Design of New Buildings except
Low-Rise Residential Buildings.
D.
Unit shall be safety certified by ETL and ETL US listed. Unit nameplate shall
include the ETL/ETL Canada label.
1.03 Submittals
A.
Product Data: Literature shall be provided that indicates dimensions, operating and
shipping weights, capacities, ratings, fan performance, filter information, factory
supplied accessories, electrical characteristics, and connection requirements.
Installation, Operation and Maintenance manual with startup requirements shall be
provided.
B.
Shop Drawings: Unit drawings shall be provided that indicate assembly, unit
dimensions, construction details, clearances, and connection details. Computer
generated fan curves for each fan shall be submitted with specific design operation
point noted. Wiring diagram shall be provided with details for both power and
control systems and differentiate between factory installed and field installed wiring.
1.04 Delivery, Storage, and Handling
A.
Unit shall be wrapped in special heat shrink plastic covering the entire unit for
supplemental unit protection to prevent damage during transport and thereafter while
in storage awaiting installation.
B.
Unit shall be crated for shipment. Crate shall be fabricated of dimensional lumber
and plywood.
C.
Follow Installation, Operation and Maintenance manual instructions for rigging,
moving, and unloading the unit at its final location.
D.
Unit shall be handled carefully to avoid damage to components, enclosures and
finish.
E.
Unit shall be stored in a clean, dry place protected from construction traffic in
accordance with the Installation, Operation and Maintenance manual.
1.05 Warranty
A.
Manufacturer shall provide a limited “parts only” warranty for a period of 12 months
from the date of equipment startup or 18 months from the date of original equipment
shipment from the factory, whichever is less. Warranty shall cover material and
workmanship that prove defective, within the specified warranty period, provided
manufacturer’s written instructions for installation, operation and maintenance have
been followed. Warranty excludes parts associated with routine maintenance, such as
belts and filters.
Part 2 - Products
2.01 Manufacturer
A.
1.
Products shall be provided by the following manufacturers:
AAON
2.02 Air Handling Units
A.
General Description
1.
Indoor air handling units shall include filters, supply fans, DX evaporator coil,
reheat coil, electric heaters, and unit controls.
2.
Unit shall have a draw-through supply fan configuration and discharge air
vertically.
3.
Unit shall be factory assembled and tested including leak testing of the DX coil,
and run testing of the supply fans and factory wired electrical system. Run test
report shall be supplied with the unit.
4.
Unit shall have decals and tags to indicate lifting and rigging, service areas and
caution areas for safety and to assist service personnel.
5.
Unit components shall be labeled, including pipe stub outs, refrigeration system
components and electrical and controls components.
6.
Installation, Operation and Maintenance manual shall be supplied within the unit.
7.
Laminated color-coded wiring diagram shall match factory installed wiring and
shall be affixed to the interior of the control compartment’s hinged access door.
8.
Unit nameplate shall be provided in two locations on the unit, affixed to the
exterior of the unit and affixed to the interior of the control compartment’s hinged
access door.
B.
Construction
1.
All cabinet walls, access doors, and roof shall be fabricated of double wall, impact
resistant, rigid polyurethane foam panels.
2.
Unit insulation shall have a minimum thermal resistance R-value of 6.25. Foam
insulation shall have a minimum density of 2 pounds/cubic foot and shall be tested
in accordance with ASTM D1929-11 for a minimum flash ignition temperature of
610°F.
3.
Unit construction shall be double wall with G90 galvanized steel on both sides and
a thermal break. Double wall construction with a thermal break prevents moisture
accumulation on the insulation, provides a cleanable interior, prevents heat transfer
through the panel, and prevents exterior condensation on the panel.
4.
Unit shall be designed to reduce air leakage and infiltration through the cabinet.
Sealing shall be included between panels and between access doors and openings
to reduce air leakage. Piping and electrical conduit through cabinet panels shall
include sealing to reduce air leakage.
5.
Access to filters, cooling coil, reheat coil, supply fans, and electrical and controls
components shall be through hinged access doors.
6.
Access doors shall be flush mounted to cabinetry. Coil access door and supply fan
access door shall include quarter-turn lockable handles. Supply fan access door
shall include removable pin hinges.
7.
Units with a cooling coil shall include sloped 304 stainless steel drain pan. Drain
pan connection shall be on the right hand side of unit.
8.
Cooling coil shall be mechanically supported above the drain pan by multiple
supports that allow drain pan cleaning and coil removal.
9.
Unit shall include exterior corrosion protection which shall be capable of
withstanding at least 2,500 hours, with no visible corrosive effects, when tested in
a salt spray and fog atmosphere in accordance with ASTM B 117-95 test
procedure.
C.
Electrical
1.
Unit shall be provided with an external control panel with separate low voltage
control wiring with conduit and high voltage power wiring with conduit between
the control panel and the unit. Control panel shall be field mounted.
2.
Unit shall include a factory installed 24V control circuit transformer.
3.
Unit shall be provided with phase and brown out protection which shuts down all
motors in the unit if the electrical phases are more than 10% out of balance on
voltage, the voltage is more than 10% under design voltage or on phase reversal.
4.
D.
Unit shall contain dual point power. One circuit will be for the fan and one circuit
will be for the electric heat.
Supply Fans
1.
Unit shall include direct drive, unhoused, backward curved, plenum supply fans.
2.
Blower and motor assembly shall be dynamically balanced.
3.
Blower and motor assembly shall be mounted on rubber isolators.
4.
Motor shall be a high efficiency electronically commutated motor (ECM).
E.
Cooling Coil
1.
F.
Evaporator Coil
a.
Coil shall be designed for use with R-410A refrigerant and constructed of
copper tubes with aluminum fins mechanically bonded to the tubes and
aluminum end casings. Fin design shall be sine wave rippled.
b.
Coil shall be 6 row high capacity and 12 fins per inch.
c.
Coil shall be hydrogen or helium leak tested.
d.
Coil shall be furnished with factory installed thermostatic expansion valves. The
sensing bulbs shall be field installed on the suction line immediately outside the
cabinet.
e.
Coil shall have right hand external piping connections. Liquid and suction
connections shall be sweat connection. Coil connections shall be labeled, extend
beyond the unit casing, and be factory sealed on both the interior and exterior of
the unit casing, to minimize air leakage.
Refrigeration System
1.
Air handling unit and matching condensing unit shall be capable of operation as an
R-410A split system air conditioner.
2.
Each refrigeration circuit shall be equipped with thermostatic expansion valve type
refrigerant flow control.
3.
Modulating hot gas reheat shall be provided on the refrigeration circuit.
Refrigeration circuit shall be provided with hot gas reheat coil, modulating valves,
electronic controller, supply air temperature sensor and a dehumidification mode
of operation, which includes supply air temperature control to prevent supply air
temperature swings and overcooling of the space. Modulating reheat valves shall
be factory installed in the matching AAON condensing unit. Reheat line
connections shall be labeled, extend beyond the unit casing and be located near the
suction and liquid line connections for ease of field connection. Connections shall
be factory sealed on both the interior and exterior of the unit casing to minimize air
leakage.
G.
Electric Heating
1.
Unit shall include an electric heater consisting of electric heating coils, fuses, and a
high temperature limit switch, with capacities as shown on the plans.
2.
Electric heating coils shall be located in the reheat position downstream of the
supply fan.
3.
Electric heater shall have full modulation capacity controlled by an SCR (Silicon
Controlled Rectifier). Controller shall provide the heating control signal to control
the amount of heating.
H.
Filters
1.
Unit shall include 4 inch thick, pleated panel filters with an ASHRAE efficiency of
95% and a MERV rating of 14, upstream of the cooling coil. Unit shall also
include 2 inch thick, pleated panel pre filters with an ASHRAE efficiency of 30%
and MERV rating of 8, upstream of the 4 inch standard filters.
2.
Unit shall include a clogged filter switch.
3.
Unit shall include factory installed Magnehelic gauge measuring the pressure drop
across the filter rack.
I.
Controls
1.
Unit shall be provided with an external control panel with separate low voltage
control wiring with conduit and high voltage power wiring with conduit between
the control panel and the unit. Control panel shall be field mounted.
2.
Factory Installed and Factory Provided Controller
a.
Unit controller shall be capable of controlling all features and options of the
unit. Controller shall be factory installed in the unit controls compartment and
factory tested.
b.
Controller shall be capable of stand alone operation with unit configuration,
setpoint adjustment, sensor status viewing, unit alarm viewing, and occupancy
scheduling available without dependence on a building management system.
c.
Controller shall have an onboard clock and calendar functions that allow for
occupancy scheduling.
d.
Controller shall include non-volatile memory to retain all programmed values
without the use of a battery, in the event of a power failure.
e.
Constant Volume Controller
f.
1.
Unit shall modulate cooling with constant airflow to meet space temperature
cooling loads.
2.
With modulating hot gas reheat, unit shall modulate cooling and hot gas
reheat as efficiently as possible, to meet space humidity loads and prevent
supply air temperature swings and overcooling of the space.
3.
Unit shall modulate heating with constant airflow to meet space temperature
heating loads. Modulating heating capacity shall modulate based on supply air
temperature.
Unit configuration, setpoint adjustment, sensor status viewing, unit alarm
viewing, and occupancy scheduling shall be accomplished with connection to
interface module with LCD screen and input keypad, interface module with
touch screen, or with connection to PC with free configuration software.
Controller shall be capable of connection with other factory installed and factory
provided unit controllers with individual unit configuration, setpoint adjustment,
sensor status viewing, and occupancy scheduling available from a single unit.
Connection between unit controllers shall be with a modular cable.
Part 3 - Execution
3.01 Installation, Operation and Maintenance
A.
Installation, Operation and Maintenance manual shall be supplied with the unit.
B.
Installing contractor shall install unit, including field installed components, in
accordance with Installation, Operation and Maintenance manual instructions.
C.
Start up and maintenance requirements shall be complied with to ensure safe and
correct operation of the unit.
Guide Specifications - Condensing Units CU-1-3 and CU-1-4
Part 1 - General
General Description
A.
This section includes the design, controls and installation requirements for air-cooled
condensers / condensing units.
Quality Assurance
A.
Unit shall be certified in accordance with UL Standard 1995/CSA C22.2 No. 236,
Safety Standard for Heating and Cooling Equipment.
B.
Unit and refrigeration system shall comply with ASHRAE 15, Safety Standard for
Mechanical Refrigeration.
C.
System Seasonal Energy Efficiency Ratio (SEER) shall be equal to or greater than
prescribed by ASHRAE 90.1, Energy Efficient Design of New Buildings except
Low-Rise Residential Buildings.
D.
Unit shall be safety certified by ETL and be ETL US and ETL Canada listed. Unit
nameplate shall include the ETL/ETL Canada label.
Submittals
A.
Product Data: Literature shall be provided that indicates dimensions, operating and
shipping weights, capacities, ratings, factory supplied accessories, electrical
characteristics, and connection requirements. Installation, Operation and
Maintenance manual with startup requirements shall be provided.
B.
Shop Drawings: Unit drawings shall be provided that indicate assembly, unit
dimensions, construction details, clearances, and connection details. Wiring diagram
shall be provided with details for both power and control systems and differentiate
between factory installed and field installed wiring.
Delivery, Storage, and Handling
A.
Follow Installation, Operation and Maintenance manual instructions for rigging,
moving, and unloading the unit at its final location.
B.
Unit shall be stored in a clean, dry place protected from construction traffic in
accordance with the Installation, Operation and Maintenance manual.
Warranty
A.
Manufacturer shall provide a limited “parts only” warranty for a period of 12 months
from the date of equipment startup or 18 months from the date of original equipment
shipment from the factory, whichever is less. Warranty shall cover material and
workmanship that prove defective, within the specified warranty period, provided
manufacturer’s written instructions for installation, operation and maintenance have
been followed. Warranty excludes parts associated with routine maintenance and
refrigerant.
B.
Compressors shall carry a 5 warranty from date of original equipment shipment from
the factory.
Part 2 - Products
Manufacturer
A.
1.
Products shall be provided by the following manufacturers:
AAON
Condensing Units
A.
General Description
1.
Condensing unit shall include compressors, air-cooled condenser coils, condenser
fans, suction and liquid connection valves, and unit controls.
2.
Unit shall be factory assembled and tested including leak testing of the coil and
run testing of the completed unit. Run test report shall be supplied with the unit in
the controls compartment’s literature pocket.
3.
Unit shall have decals and tags to indicate lifting and rigging, service areas and
caution areas for safety and to assist service personnel.
4.
Unit components shall be labeled, including pipe stub outs, refrigeration system
components and electrical and controls components.
5.
Installation, Operation and Maintenance manual shall be supplied within the unit.
6.
Laminated color-coded wiring diagram shall match factory installed wiring and
shall be affixed to the interior of the control compartment’s access door.
7.
Unit nameplate shall be provided in two locations on the unit, affixed to the
exterior of the unit and affixed to the interior of the control compartment’s access
door.
B.
Construction
1.
Unit shall be completely factory assembled, piped, and wired and shipped in one
section.
2.
Unit shall be specifically designed for outdoor application.
3.
The condenser coil shall be mechanically protected from physical damage by a
wire guard covering the full area of the coil.
4.
Exterior paint finish shall be capable of withstanding at least 2,500 hours, with no
visible corrosive effects, when tested in a salt spray and fog atmosphere in
accordance with ASTM B 117-95 test procedure.
5.
C.
Unit shall include a forkliftable base.
Electrical
1.
Unit shall be provided with standard power block for connecting power to the unit.
2.
Control circuit transformer and wiring shall provide 24 VAC control voltage from
the line voltage provided to the unit.
3.
Unit shall be provided with phase and brown out protection which shuts down all
motors in the unit if the electrical phases are more that 10% out of balance on
voltage, the voltage is more that 10% under design voltage, or on phase reversal.
D.
Refrigeration System
1.
Unit shall include a variable capacity scroll compressor on the refrigeration circuit
which shall be capable of modulation from 10-100% of its capacity.
2.
Each compressor shall be furnished with a crankcase heater.
3.
Compressors shall be mounted in an isolated service compartment which can be
accessed without affecting unit operation.
4.
Compressors shall be isolated from the base pan with the compressor
manufacturer’s recommended rubber vibration isolators, to reduce any
transmission of noise from the compressors into the building area.
5.
Each refrigeration circuit shall be equipped with automatic reset low pressure and
manual reset high pressure refrigerant safety controls, Schrader type service
fittings on both the high pressure and low pressure sides, and service valves for
liquid and suction connections. Liquid line filter driers shall be factory provided.
Finished field installed refrigerant circuits shall include the low side cooling
components, refrigerant, thermal expansion valve, liquid line, insulated hot gas
line and insulated suction line.
6.
Unit shall include a factory holding charge of R-410A refrigerant and oil.
7.
Refrigeration circuit shall be provided with hot gas reheat coil in the matching air
handler, modulating valves, electronic controller, supply air temperature sensor
and a dehumidification control signal terminal which allow the unit to have a
dehumidification mode of operation, which includes supply air temperature control
to prevent supply air temperature swings and overcooling of the space.
8.
Condensing unit shall be provided with adjustable on/off condenser fan cycling
head pressure control and adjustable compressor lockout to allow cooling
operation down to 35°F.
9.
Units shall be provided with a suction pressure transducer on the refrigeration
circuit.
Condensers
A.
Air-Cooled Condenser
1.
Condenser fan shall be horizontal discharge, axial flow, direct drive fans.
2.
Fan motor shall be weather protected, single phase, direct drive, and open drip
proof with inherent overload protection.
3.
Coils shall be designed for use with R-410A refrigerant and constructed of copper
tubes with aluminum fins mechanically bonded to the tubes and aluminum end
casings. Fin design shall be sine wave rippled.
4.
Coils shall be designed for a minimum of 10°F of refrigerant sub-cooling.
5.
Coils shall be hydrogen or helium leak tested.
Controls
A.
1.
Standard Terminal Block
Unit shall be provided with a terminal block for field installation of controls.
Part 3 - Execution
Installation, Operation, and Maintenance
A.
Installation, Operation and Maintenance manual shall be supplied with the unit.
B.
Installing contractor shall install unit, including field installed components, in
accordance with Installation, Operation and Maintenance manual instructions.
C.
Start up and maintenance requirements shall be complied with to ensure safe and
correct operation of the unit.
Performance
Split System Rating
23
22
21
20
19
18
17
16
15
14B
14A
13
12
11
9
10
8
7
6C
6B
6A
5C
5B
5A
4
3
2
1C
1D
1B
1A
2425 South Yukon Ave - Tulsa, Oklahoma 74107-2728 - Ph. (918) 583-2266 Fax (918) 583-6094
AAONEcat32 Ver. 4.226 (SN: 6354480-C6MRRYWC)
V3-BRB-9-0-161C-3BS:AACB-HBA-000-0J0-C0A0AC0-00-C0000F00X
Air Handling Unit Tag: FCU-1-3, FCU-1-4
C
C
- C
-
0
0 4
-
9
- D
-
1
: D
D
D
0 E
A
0
Condensing Unit Tag: CU-1-3, CU-1-4
Job Information
Unit Information
**WEIGHT AND PERFORMANCE DO NOT INCLUDE SPA
Job Name:
Job Number:
Site Altitude:
Refrigerant
Northside Cosmetic Surgery
31615 - submit
0 ft
R-410A
Approx. Weights AHU/CU:
Supply CFM/ESP:
Ambient Temperature:
Return Temperature:
1.00 in. wg.
0.31 in. wg.
0.31 in. wg.
0.5 in. wg.
Economizer:
Heating:
Cabinet:
Total:
659 / 260 lbs. (±5%)**
1015 / 1 in. wg.
95 ºF DB / 75 ºF WB
70 ºF DB / 59 ºF WB
Static Pressure
External:
Evaporator:
Filters Clean:
Dirt Allowance
Cooling Section
0.03 in. wg.
2.15 in. wg.
Heating Section
Total Capacity:
Sensible Capacity:
Latent Capacity:
HW Total Cooling Capacity:
Mixed Air Temp:
Entering Air Temp:
Lv Air Temp (Coil):
Lv Air Temp (Unit)
Evap Suction Temp:
Supply Air Fan:
SA Fan RPM / Width:
Gross
43.16
30.64
12.52 MBH
0.21 MBH
75.05 ºF DB
75.05 ºF DB
46.97 ºF DB
48.73 ºF DB
39.91 ºF
1 x 310AX @ 0.68 BHP
2083 / 5.790"
Net
41.13 MBH
28.61 MBH
Evaporator Coil:
Evaporator Face Velocity:
3.7 ft² / 6 Rows / 12 FPI
276.8 fpm
62.70 ºF WB
62.70 ºF WB
46.77 ºF WB
47.59 ºF WB
Auxiliary Heating Type*:
Heating CFM:
Total Capacity:
Entering Air Temp:
Leaving Air Temp:
Input:
Heater Qty (Hi/Low):
Electric Heat FLA:
Electric Heat
1015
35.8 MBH
70.0 ºF DB / 60.0 ºF WB
102.7 ºF DB / 70.7 ºF WB
10.5 kW
2
50
Re-Heat Coil:
Capacity:
LA DB / WB:
RH:
23 MBH
68.00 ºF / 55.83 ºF
46%
EER - ARI Listing Information
Application EER @ Op. Conditions:
Condensing Unit EER @ Op. Conditions:
10.4
12.9
AH Electrical Data
Rating:
208/1/60
Minimum Circuit Amp:
Maximum Overcurrent:
7 (circuit 1), 63 (circuit 2)
15 (circuit 1), 70 (circuit 2)
208/1/60
25
Minimum Circuit Amp:
Maximum Overcurrent:
30
45
CU Electrical Data
Rating:
Unit FLA:
Compressor 1:
Condenser Fans:
Supply Fan:
Qty
1
1
1
HP
0.50
2.10
VAC
208
208
208
Phase
1
1
1
RPM
FLA
1075
2580
4.4
6.4
RLA
20.2
*Motor heat is not included.
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:06 PM
12" EBM Plenum
2425 South Yukon Ave - Tulsa, Oklahoma 74107-2728 - Ph. (918) 583-2266 Fax (918) 583-6094
AAONEcat32 Ver. 4.226 (SN: 6354480-C6MRRYWC)
JOB INFORMATION:
Job Name:
Job Tag:
Rep Firm:
Date:
WHEEL SPECIFICATION:
Max RPM:
Diameter x Qty:
CFM:
Tip Speed:
Inertia:
Northside Cosmetic Surgery
FCU-1-3, FCU-1-4
03/17/2015
OPERATING CONDITIONS:
MOTOR SELECTION:
Air Flow:
Static Pressure:
Relief Dampers DP:
1,015 CFM
2.15 in. Wg.
0.00 in. Wg.
TSP:
Site Altitude:
TSP @ Sea Level:
2.15 in. Wg.
0.00 Ft
2.15 in. Wg.
Rated HP / Bypass:
Frame Size:
Nominal RPM:
VAC/PH/HZ:
Efficiency
Enclosure Type:
Max Inertial Load:
FAN PERFORMANCE:
RPM:
BHP:
Efficiency:
In/Out Velocity:
Plenum Out Velocity:
2,580
12.5 in. x 1
1015
6,806 FPM
3 WR²
2.1 / No
ECM
2580
208/1/60
Premium / 0.855
ODP
27 WR²
FAN SOUND POWER (Inlet/Outlet):
Octave Band:
(Re 10^-12 watts)
1
2
3
4
5
6
7
63
68
75
68
65
65
62
67
70
77
73
74
72
68
SOUND POWER A-Weighted: 71 / 77 dB
2083
0.68
50.6%
883/923 FPM
11 FPM
Max Duct SP with Blocked Airway:
8
59
64
2.3 in. Wg. @ 2083 rpm
Supply Fan Model: 310AX @ 2083 RPM and 100% Width
Design Conditions: 1015 CFM @ 2.15" SP
RPM
BHP
SYSTEM
Efficiency
SP Surge
CFM Min
2
2
RPM: 2083
40%
SP
BHP
1
1
20%
EFFICIENCY: 50.55
BHP: 0.68
0
0
1
2
CFM x 1000
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:07 PM
Selected Options
Unit Submittal
23
22
21
20
19
18
17
16
15
14B
14A
13
12
11
9
10
8
7
6C
6B
6A
5C
5B
5A
4
3
2
1C
1D
1B
1A
203 Gum Springs Road - Longview, TX 75602 - Ph. (903) 236-4403 Fax (903) 236-4463
AAONEcat32 Ver. 4.226 (SN: 6354480-C6MRRYWC)
V3-BRB-9-0-161C-3BS:AACB-HBA-000-0J0-C0A0AC0-00-C0000F00X
Tag: FCU-1-3, FCU-1-4
Job Name:
Job Number:
V
3
B
R
B
9
0
1
6
1
C
3
B
S
Paulson-Cheek Mechanical
March 16, 2015
Base Option
Description
Series
Vertical Unit
Generation
Third Generation
Unit Size
Up to 2,000 cfm
Unit Orientation
Right Hand Connections - Top Discharge, Back Intake (Vertical)
Revision
Second Revision
Voltage
208V/1Ø/60Hz
Corrosion Protection
None
Cooling Type
R-410A DX Cooling
Cooling Rows
6 Row Coil
Cooling Stages
Single Circuit
Cooling FPI
12 fpi
Heating Type
Electric Heat
Heating Designation
14 kW (10.5 kW @ 208V)
Heating Stages
Modulating/SCR Electric
Feature Option
A
A
C
B
H
B
A
0
0
0
0
J
0
C
0
A
0
A
C
0
0
0
C
0
0
0
0
F
0
0
X
Unit Submittal For:
Unit Submittal Date:
Northside Cosmetic Surgery
31615 - submit
Description
1A. SA Blower Configuration
1 Blower + 1 High Efficiency EC Motor
1B. SA Blower Model
310 mm Backward Curved Plenum
1C. SA Blower Motor
1.7 kW
1D. SA Blower Control/Contol Vendor
WattMaster Orion Controls System
2. Refrigeration Options
Modulating Hot Gas Reheat (MHGR)
3. Special Controls
Constant Volume Controller + Modulating Hot Gas Reheat - CV Cool + CV Heat
4. Additional Controls
Phase and Brownout Protection
5A. Mixing Box - RA Damper Position
Standard - None
5B. Mixing Box - OA Damper Position
Standard - None
5C. Mixing Box - Damper Control
Standard - None
6A. Filter Box - Pre Filter Box
Standard - None
6B. Filter Box - Unit Filter
2" Pleated - 30% Eff. + 4" Pleated - 95% Eff. - MERV 14
6C. Filter Box - Final Filter Box
Standard - None
7. Filter Options
Magnehelic Gauge + Clogged Filter Switch
8. Coil Coating
Standard - None
9. Expansion Valve
Thermal Expansion Valves
10. Expansion Valve Controls
None
11. External Paint
AAON Gray Paint
12. Tonnage
4 ton Capacity
13. Added or Modified Systems
Standard - None
14A. GPM Cooling Coil
Standard
14B. GPM Heating Coil
Standard
15. Control Panel
Large Control Panel - 48" x 22"
16. Cabinet
Standard
17. Blank
Standard - None
18. Preheat
Standard - None
19. Blank
Standard - None
20. Crating
Forkliftable Base + Shipping Shrink Wrap
21. Pulley Combination
Standard - None
22. Warranty
Standard - 1 Year Parts
23. Type
Special Pricing Authorization
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:07 PM
203 Gum Springs Road - Longview, TX 75602 - Ph. (903) 236-4403 Fax (903) 236-4463
AAONEcat32 Ver. 4.226 (SN: 6354480-C6MRRYWC)
C
C
-
C
-
0
0
4
-
9
-
D
-
1
:
D D D
0
E
A
0
Tag: CU-1-3, CU-1-4
Job Name:
Job Number:
C
C
C
004
9
D
1
Northside Cosmetic Surgery
31615 - submit
Base Option
Description
Series
Condensing Unit
Generation
3rd Generation
Revision
Third Revision
Unit Size
Four Tons - Horizontal Discharge
Voltage
208V/1Ø/60Hz
Compressors
Variable Capacity Scroll Compressor – Lead Circuit
Circuits
One Circuit
Feature Option
D
D
D
0
E
A
0
Unit Submittal For:
Unit Submittal Date:
Paulson-Cheek Mechanical
March 16, 2015
Description
1 Ambient Control
Modulating Fan Pressure Control (35°F Ambient)
2 Refrigeration Option
Modulating Hot Gas Reheat
3 Control
Suction Pressure Transducer + Phase and Brown Out Protection
4 Coil
Standard - Copper tube coil with aluminum fins
5 Cabinet
Compressor Sound Blanket + 2,500 Hour Salt-Spray Tested Exterior Paint
6 Warranty
Second To Fifth Year Extended Compressor Warranty
7 Type
Standard
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:11 PM
Drawings
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:07 PM
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:07 PM
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:07 PM
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:11 PM
Field Piping
Refrigeration Acccessories
23
22
21
20
19
18
17
16
15
14B
14A
13
12
11
9
10
8
7
6C
6B
6A
5C
5B
5A
4
3
2
1C
1D
1B
1A
2425 South Yukon Ave - Tulsa, Oklahoma 74107-2728 - Ph. (918) 583-2266 Fax (918) 583-6094
AAONEcat32 Ver. 4.226 (SN: 6354480-C6MRRYWC)
V3-BRB-9-0-161C-3BS:AACB-HBA-000-0J0-C0A0AC0-00-C0000F00X
Air Handling Unit Tag: FCU-1-3, FCU-1-4
C
C
-
C
-
0
0
4
-
9
-
D
-
1
:
D
D
D
0
E
A
0
Condensing Unit Tag: CU-1-3, CU-1-4
Job Information
Job Name:
Northside Cosmetic Surgery
Job Number:
31615 - submit
Factory Supplied / Factory Installed
Quantity
1
2
Description
Reversible Thermal Expansion Valve, CBBIZE-5
Modulating Refrigerant Valve, SDR-3
Part #:
29576
28387
Location
AHU
CU
Factory Supplied / Field Installed
Quantity
1
1
Description
Part #:
29062
29901
Receiver, 4 lb.
Filter Drier
Location
CU
CU
Field Supplied / Field Installed
Quantity
-
Description
P-Trap(s)
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Part #:
Location
AHU
Date Printed: 3/17/2015 12:00:06 PM
Circuit #: 1
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:06 PM
Controls
VCMX Components
23
22
21
20
19
18
17
16
15
14B
14A
13
12
11
9
10
8
7
6C
6B
6A
5C
5B
5A
4
3
2
1C
1D
1B
1A
2425 South Yukon Ave - Tulsa, Oklahoma 74107-2728 - Ph. (918) 583-2266 Fax (918) 583-6094
AAONEcat32 Ver. 4.226 (SN: 6354480-C6MRRYWC)
V3-BRB-9-0-161C-3BS:AACB-HBA-000-0J0-C0A0AC0-00-C0000F00X
Tag: FCU-1-3, FCU-1-4
Job Name:
Northside Cosmetic
Surgery
31615 - submit
Job Number:
VCMX For:
Paulson-Cheek Mechanical
VCMX Date:
March 16, 2015
Hardware Included For VCMX Controller
Included Parts
Part #
31422
28606
28503
28503
28505
30308
28626
29644
30126
VCMX
Controller
with E-Bus
Analog In
Analog Out
Binary In
Relay Out
Digital
Sensor(s)
Analog In
VCMX Large
Analog Out
Expansion
Binary In
Module
Relay Out
VCMX Controller with E-Bus
Space Temp Sensor - Field Installed
Supply Air Temp Sensor - Field Installed
Return Air Temp Sensor
Outside Air Temp Sensor
VCMX Large Expansion Module
Dirty Filter Sensor
Space Humidity Sensor - Field Installed
Suction Pressure Transducer (Installed in Condensing Unit)
1
X
2
X
X
X
X
1
2
X
X
X
3
X
4
X
5
X
6
7
X
3
X
X
4
5
6
7
Assigned Channel
MainController\AI1
MainController\AI2
MainController\AI3
MainController\AI4
LargeExpansionModule\BI2
LargeExpansionModule\AI2
LargeExpansionModule\AI3
8
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:07 PM
Control Terminals
2425 South Yukon Ave - Tulsa, Oklahoma 74107-2728 - Ph. (918) 583-2266 Fax (918) 583-6094
AAONEcat32 Ver. 4.226 (SN: 6354480-C6MRRYWC)
C
C
-
C
-
0
0
4
-
9
-
D
-
1
:
D
D
D
0
E
A
0
Condensing Unit Tag: CU-1-3, CU-1-4
Job Information
Job Name:
Northside Cosmetic Surgery
Job Number:
31615 - submit
Terminals Available/Required for Controlling the Unit
Terminal Point
[R]
[C]
[Y1]
[CC1-] & [CS1+]
[P5-] & [P6+]
[G/R], [R/G], [W] & [B]
Description
24VAC Control Voltage
Common
Cooling Stage 1 Enable
Variable Capacity Compressor (0-5 VDC) Signal
Suction Pressure Sensor - Compressor 1 (0-5 VDC)
SDR VALVE
Date Created/Modified: 3/16/2015 4:54:09 PM Using Ver 4.226 (OSN# 6354480)
Date Printed: 3/17/2015 12:00:11 PM
FG-32
DDC Energy Controller,
Internet and Cloud Ready
 ARM 9 S3C2410 200MHz
Main Processor
 SuperCap Apps Safety
Backup
 M3 Cortex Processor for
the I/O
 16 Mbyte NOR Flash
 24V AC/DC Power
 64 Mbyte SDRAM
 SD Card Reader for
Histories and Graphics
 1 x 10/100 Ethernet Port
 1 x Mini USB
 2 x RS485
 16 x UI
 8 x DO/LED for Status
 8 x UO (200mA sink
for Switching Relays)
 Remote Flash Upgrades
 HTML5 Web Server
on Board!
 RTC
The new FG series of Open Automation Controllers from EasyIO are the new range of Internet ready Field
Controllers. They comprise of combined Area Controller capabilities and features, as well built in I/O, and huge
data logging capacity, all packaged as the future solution for the Internet of things, in Energy and Building
Facility Control. The Controller also supports multi concurrent protocols and services such as BACnet, Modbus,
TCOM, Web Services, and both Server and Client services.
This new range complies with the ‘Internet of Things’ by interfacing directly to Cloud Services, without an
additional Gateway, or Server. To power the application, The FG has a dual ARM processor engine, and also a
built-in Web Server.
The FG series change the way that we will deploy Building Automation, especially in multiple Facilities and
hardware or middleware. We see this range of FG Controllers allowing us and the industry to extend their
reach deeper and wider into all kinds of Energy Performance Solutions. Ranging from Retail Stores, Schools,
and Residential, Smart Grid and so on.
Another exciting feature, is the openness, and its web friendly tools to enable 3rd Party Tools to be deployed
in addition to the Workbench that we are all familiar with today. This platform will meet the needs of simple
controls requirements and complex HVAC plants, such as Chiller Sequencing and Roof Top Control. Truly a
welcome change!
Graphics will also be served from the FG Engine, nicely embedded in the Linux OS. To compliment this there
will be third party Graphics Tools that will be used to design and implement Graphic Screens, the content
being stored in the built-in micro SD Card slot (up to 16GB).
Features
 Power! – TWO ARM processors
 Memory/Storage – SD Card and massive history storage
 Supports BACnet, TCOM, Modbus and Web Services
 Fills a Gap in the market, between an Area Controller and the EasyIO 30P controller
 Html5 Graphics! – IPAD friendly
Specifications
 ARM 9 S3C2410 200MHz Main Processor
 1 x Mini USB
 M3 Cortex Processor for the I/O
 2 x RS485
 16 Mbyte NOR Flash
 RTC
 64 Mbyte SDRAM
 SuperCap Apps Backup
 SD Card Reader
 24V AC/DC Power
 1 x 10/100 Ethernet Port
Device Info
Model
EasyIO-FG-32
Description
EasyIO-FG32 Sedona series: 32 I/O Controller
Name
FG32 DDC
Device Specifications
Mechanical
Electrical
Dimensions
9.2 in x 4.9 in x 1.7 in (233 mm x 124 mm x 44 mm)
Material
UL Approved Plastic
Weight
800gram
Power Supply
24V AC +/- 5% or 24V DC +20%/-15%
Consumption
18VA
Current Rating
750mA at 24VAC/VDC
Operating Temp
32 to 150°F (0 to 65°C)
Storage Temp
-4 to 150°F (-20 to 65°C)
Operating Humidity 10% to 95% relative humidity non-condensing
Inputs & Outputs
UO: 3 modes. Voltage mode, output range: 0-10V; Current mode, output range: 0-20mA;
Digital mode, maximum sinking current: 200mA DC only at 200mA max.
UI: 5 modes: Digital mode, voltage free contact input, Resistance mode, input range: 500-500Kohm;
Voltage mode, input range: 0-10V; Current mode, input range: 0-20mA;
Pulse count mode, maximum pulse frequency: 20Hz
DO: Relay output with contact rating 1A 30VDC
Communication
Physical Interface
1 & 2 (Port 1 & 2)
EIA-485 (BUS A, B) Two-wire, Half Duplex
Modbus Baud Rate
Speed: (9.6K, 19.2k, 38.4K, 57.6K, 115.2K bit/s), Data Bit: (8 bits), Parity: (None, Even, Odd)
Bacnet Baud Rate
Speed: (9.6K, 19.2k, 38.4K, 76.8K), Data Bit: (8 bits), Parity: (None)
Ethernet Support
IP, TCP, UDP, ICMP, HTTP, FTP
Application Support
Sox, TCOM driver, Modbus, BACnet
EasyIO Holdings Pte Ltd
www.EasyIO.com
C
UL Us
R
LISTED
All specifications subject to change without notice or liability to provide changes to prior purchasers. Information and specifications published here are
current as of the date of publication of this document. EasyIO Holdings, reserves the right to change or modify specifications without prior notice. The
latest product specifications can be found by contacting our corporate headquarters, Singapore. Products or features contained herein may be covered by
one or more U.S. or foreign patents. All brands and product names are trademarks or registered trademarks of their respective owners. Copyright © 2013 all
rights reserved, EasyIO Holdings.
FC-20
The EasyIO FC Series
FC 20 Standalone Controller
The EasyIO FC series is aimed at affordable ‘canned’ solutions for standalone applications, such as Roof Top
Units, Fan Coils, AHU’s, package units etc.
The FC20 is the first product in the FC range, designed to complement the 30P and FG series of awarding
wining excellence. All of the FC series products are equipped with two RS485 ports and no Ethernet port,
for Ethernet applications you can upscale to the 30P or FG series. All FC products are BACnet and Modbus
Selectable and can be programmed via the CPT Tool from Online Tools Inc.
The FC 20 has 20 points of I/O and priced to meet most high volume applications and price points. The new
FC-20 is a microprocessor based controller consisting of 20 inputs/outputs (I/O) to accommodate general and
specific applications featuring BACnet MSTP and Modbus RTU communication protocols. 20 IOs include, 12
Universal Inputs (UI) supporting current, voltage and resistance based sensor, 4 electrically isolated Digital
Outputs (DO) and 4 Analog Inputs supporting current and voltage outputs.
The FC-20 comes with one standard RS485 driver to support either BACnet MSTP or Modbus RTU
communication (selection via hardware dip-switch). This communication port is also used as configuration/
setting and firmware upgrade.
The concept behind the FC series is that the FC-20 is configured can be used as an input/output controller
only, or an Application Specific Application Controller. There is also a Real-time clock and a second RS485
(reserved for communicating with other Modbus devices such as Power Meters) are provided for
such application.
Specifications
Model
EasyIO-FC-20
CPU
ARM Cortex-M3, 24MHz
Name
FC 20
Device Specifications
Mechanical
Electrical
Input/Output
Dimensions
215 mm (L) x 125 mm (W) x 45 mm (H)
Weight
410gram
Power Supply
24VAC 50/60Hz ±5%, or 20VDC~34VDC
Consumption
<11VA
Current Rating
500mA at 24VAC/VDC
Operating Temp
0°C to 65°C (32° to 149°F)
Storage Temp
-20°C to 85°C (-4° to 185°F)
Operating Humidity
10% to 95% Relative Humidity, Non-condensing
Universal Input
12 Channels, 12-Bit ADC (with PGA)
Digital Output
Voltage
0~10V (±0.01V)
Current
4~20V (±0.01mA)
Resistance
0~30K (±50 Ohm), 0~10K (±5 Ohm)
0~1K (±1 Ohm)
Thermistor Sensor
NTC 10K Type 2/3, 3K, 20K (±0.1ºC)
RTD: 1K Balco, 1K Platinum (±0.2ºC)
4 Channels
Type
Analog Output
Relay, SPST NO, 24Vac/Vdc, 2A
4 Channels, 12-bit DAC
Voltage
0~10V
Current
4~20mA
Communication
Physical Interface 1 EIA-485 Two Wire, Half Duplex
(Port 1)
Modbus Baud Rate
Speed: 9.6K, 19.2K, 38.4K, 57.6K, 115.2K bit/s
Data Bit: 8 bits, Parity: None, Even, Odd
Bacnet Baud Rate
Speed: 9.6K, 19.2K, 38.4K, 57.6K, 76.8K bit/s
Data Bit: 8 bits, Parity: None
Protocol
Modbus RTU, BACnet MSTP
Physical Interface 2 EIA-485 Two Wire, Half Duplex
(Port 2)
Modbus Baud Rate
Speed: 9.6K, 19.2K, 38.4K, 57.6K, 115.2K bit/s
Data Bit: 8 bits, Parity: None, Even, Odd
Protocol
Modbus RTU (for Application Specific Application only)
EasyIO Holdings Pte Ltd
www.EasyIO.com
All specifications subject to change without notice or liability to provide changes to prior purchasers. Information and specifications published here are
current as of the date of publication of this document. EasyIO Holdings, reserves the right to change or modify specifications without prior notice. The
latest product specifications can be found by contacting our corporate headquarters, Singapore. Products or features contained herein may be covered by
one or more U.S. or foreign patents. All brands and product names are trademarks or registered trademarks of their respective owners. Copyright © 2013 all
rights reserved, EasyIO Holdings.
FG-LCD-MMI
For EasyIO, Sedona, JACE’s
and Supervisors
Description
status information and modify points value on building control system in additional to conventional Niagara AX
Sedona Framework™ and interfaces seamless with all Sedona-based devices and makes information accessible
from all systems connected to these devices.
Features
 Touch screen with sharp colour display
 Sedona Framework™ support
 Communicates with all Sedona devices, with EasyIOFGLcd kit
 View and edit points
 Supports multiple data types e.g. Boolean, integer, float
 Ethernet based
 Simple configuration/setup on both Sedona devices and LCD display
 Easy Firmware upgrade
 Real time data upgrade
 Small form factor
 Accessible up to 600 points per controller
 Access to multiple controller


 Simplified control of maintenance/facility team
 Watchdog governed to prevent system abnormality
 Simple and clean GUI
Technical Specifications
Power Supply
24 VAC/VDC
Power Consumption 24VA
Current Rating
1A at 24VAC/VDC
Communication
Port
Ethernet 10/100 Base-T
Processor
ARM Cortex M3 72MHz
SD Card Support
SDSC/SDHC (Card Support for Firmware Upgrades)
LCD Resolution
320 X 240
LCD Colour Depth
RGB (565)
Buzzer
Built-in
Touch Screen
Resistive 3.5”
USB Port
Mini USB (for future upgrades)
Operating Temp
0..+50°C, max 95%rh non-condensing
Storage Temp
-20..+65°C
Operating Humidity
10..95% rH non-condensing
Enclosure
IP40 (Panel Door)
CE Approval
EN61000-6-3: 2001 (Emissions)
EN61000-6-2: 2001 (Immunity)
Mounting
Panel Mounting
Terminals
High quality spring-cage terminal blocks
Dimensions
5.3 in x 4.9 in x 1.9 in (135 mm x 125 mm x 48.8 mm)
Cut-Out: 4.6 in x 3.9 in (118 mm x 98 mm)
Flexibility and Simplicity at Its Best
The FG-LCD can interface with up to 18 devices at any point in time. A device can be an
EasyIO Sedona Controller, JACE or AX Supervisor.
The Sedona devices must have the easyioFGLcd kit installed inside its Sedona platform in
order to it to communicate with the LCD display. For a JACE or Supervisor, you need to install
the easyioLcd.jar in the modules directory in the JACE or Supervisor.
The cable that is suitable to use to connect from FG-LCD to the devices is the CAT5 cable
(straight) with the RJ45 connectors and for the power, a normal power cable will be used.
EasyIO Holdings Pte Ltd
www.EasyIO.com
All specifications subject to change without notice or liability to provide changes to prior purchasers. Information and specifications published here are
current as of the date of publication of this document. EasyIO Holdings, reserves the right to change or modify specifications without prior notice. The
latest product specifications can be found by contacting our corporate headquarters, Singapore. Products or features contained herein may be covered by
one or more U.S. or foreign patents. All brands and product names are trademarks or registered trademarks of their respective owners. Copyright © 2013 all
rights reserved, EasyIO Holdings.
ACI
RH-TEMP
TEMPERATURE
Product Data
A/RH-TEMP Series
Relative Humidity/
Temperature Combinations
Automation Components, Inc.
RELATIVE HUMIDITY
Product Description
The A/RH-TEMP Series relative humidity transmitters utilize a capacitive
sensing element to deliver a proportional 4 to 20 mA, 0 to 5 VDC, or
0 to 10 VDC output. Accuracy is maintained over the entire operating range
using a thermistor for temperature compensation. This series is offered in
accuracies of 5%, 3%, 2% and 1% and in mounting configurations of room,
duct, outside, and stainless steel wall plate (Please note that stainless wall
plate models are not available in 1% accuracies).
Product Specifications
Increased resistance against
chemical vapors such as:
isopropyl, benzene, ammonia
and common cleaning agents.
Applications:
Light industrial
Pharmaceutical
-40 to 140 F (-40 to 60 C)
Capacitive
*CE, RoHS
o
o
32 to 122 F (0 to 50 C)
*TT Series transmitters are not CE compliant
Wiring Diagrams available at www.workaci.com
Process control
Made in the
USA
Automation Components, Inc.
2305 Pleasant View Rd.
Middleton, WI 53562
PH: (608) 831-2585
FAX: (608) 831-7407
RH-3
INTERFACE DEVICES
o
Pool environments
ACCESSORIES
Duct / Outside: 0 to 100 % RH Room: 0 to 95% RH (non-condensing)
o
RH Sensor Type
Approvals
Single point field calibration
Humidity chambers
RH Supply Voltage
4 to 20mA (250 Ohm Load): 15 to 40 VDC / 18 to 28 VAC
(for temperature supply voltage and 4 to 20mA (500 Ohm Load): 18 to 40 VDC / 18 to 28 VAC
additonal specs, see corresponding 0-5 VDC: 12 to 40 VDC / 18 to 28 VAC (4K Load Min.)
temperature spec sheets)
0-10 VDC: 18 to 40 VDC / 18 to 28 VAC (4K Load Min.)
Supply Current (Voltage Output) 8 mA Max.
(Current Output) 24 mA Max.
RH Measurement Range
0 to 100%
2-wire, 4 to 20mA (Factory Standard)
RH Output
3-wire, 0-5, 0-10 VDC or 4 to 20mA
+/- 1% over 20% span (between 20 to 90%)
Accuracy @ 77oF (25oC)
+/- 2%, 3%, or 5% from 10 to 95%
Long Term Stability
Less than 2% drift / 5 years
Repeatablity
0.5% RH
Sensitivity
0.1 % RH
Operating Environment
Field selectable output
signals
GAS SENSORS
The A/RH-TEMP Series is covered by ACI's Five (5) Year Limited Warranty, which is located in the front of
ACI'S SENSORS & TRANSMITTERS CATALOG or can be found on ACI's web site, which is:
www.workaci.com.
Temperature sensor output
CURRENT
Each A/RH-TEMP Series humidity transmitter is calibrated using a NIST
Traceable Temperature/Humidity Chamber. Any ACI thermistor, RTD, or
temperature transmitter may be ordered with the A/RH transmitter (see
order grid). All A/RH-TT Room combination units will have a board
mounted on the back of the enclosure.
High repeatability
PRESSURE
The A/RH-TEMP Series has on board DIP switches which allow the user to
select the desired output signal and can be powered by AC or DC power
sources. In addition, field calibration can be performed by using the on
board increment and decrement DIP switches. These enhancements provide
increased flexibility and outstanding long-term performance.
Attributes:
Low drift
TEMPERATURE
Dimensions
Outside
Room
NEW
RELATIVE HUMIDITY
(4) PG11 1/2"
(127 mm) NPT
Knockouts
3.60"
(91 mm)
0.18"
(5 mm)
O.D. Ref.
PRESSURE
Mounting Hole
Separation:
2.69" (68 mm)
R2= New Aries Enclosure OR R= Previous Infinity Enclosure
Duct
Stainless Plate
CURRENT
0.65" dia.
(17 mm)
0.75" dia.
(19 mm)
7.15"
(182 mm)
60 Micron S.S.
Sintered
Filter
0.75"
(19 mm)
GAS SENSORS
1.00"
(25 mm)
4.50"
(114 mm)
2.25"
(57 mm)
0.75" dia.
(19 mm)
2.75"
(70 mm)
(Configurations shown are based on having resistive temperature sensors)
Ordering Information
ACCESSORIES
Accuracy
A/ [
]
INTERFACE DEVICES
RH1
RH2
RH3
RH5
-[
(+/- 1%)*
(+/- 2%)
(+/- 3%)
(+/- 5%)
Temperature
Transmitters
Temp Sensor
{
]
100, 1K (Platinum RTDs)
1K-NI (Nickel RTDs)
3K, 10KS, 100KS
AN(10K Type III)
CP(10K Type II)
CSI (10K), 20K, 1.8K
TT1K**, TT100**
TTM1K**, TTM100**
*Specify a 20 % RH Range when ordering an A/RH1%
Configuration
-[
]
TT100, TT1k, TTM100,
and TTM1K model outputs
-[
(R2) Room
(4) 4 to 20mA Output
(R2O) Room w/Override
(1) 1-5 VDC Output
(R2S) Room w/Setpoint*** (2) 2-10VDC Output
(R2SO) Room w/Setpoint
***See Temperature cut sheet
&Override***
(D) Duct
for setpoint specifications
(O) Outdoor Air
(SP) Stainless Plate (Not available with the TT series
or in 1% accuracy)
**Specify a Temperature span for TT and TTM Units plus the
(SP) Stainless Plate configuration is not available for these units
2305 Pleasant View Road Middleton, WI 53562
PH: (888) 967-5224 www.workaci.com
RH-4
]
Current Monitoring
Current Switches: Fixed Trip Point
Hx00 Series
5Year
SPECIFICATIONS
Sensor Power
5A
0.1n-On ls
e
r
u
T t Mod
c
e
Sel
Warranty
N.O models: Induced from monitored
current; H800NC: 5-30VDC, permanently
connected
Insulation Class
600VAC RMS (UL), 300VAC RMS (CE)
Frequency Range
50/60 Hz, On/Off status for Variable
Frequency Drive (VFD) outputs at 12 to
115 Hz (a)
Temperature Range
H800NC, H300, H900
H600
H800, H800HV
H900
Humidity Range
Off State Leakage
-15° to 60°C (5° to 140°F)
-15° to 40°C (5° to 104°F) (to 200A); -15°
to 60°C (5° to 140°F) (to 150A)
-40° to 50°C (-40° to 122°F) (to 200A);
-40° to 75°C (-40° to 167°F) (to 100A,
& 0.25A status output)
10-90% RH non-condensing
34μ[email protected], 200μ[email protected]
(H800NC Only)
H800
On State Voltage Drop
1.9VDC (max.) @0.1A
(H800NC Only)
Terminal Block Wire Size
H600, H800, H900
H300
Terminal Block Torque
H600, H800, H900
H300
H300
Agency Approvals
H600
Maximize Reliability
Minimize Installed Cost
24-14 AWG (0.2 to 2.1 mm2);
22-16 AWG (0.3 to 1.3 mm2)
3.5 to 4.4 in-lbs (0.4 to 0.5 N-m);
7 in-lbs (0.8 N-m)
UL 508 open device listing; CE:
EN61010-1, CAT III, pollution degree 2,
basic insulation
Do not use the LED status indicators as evidence of applied voltage.
(a) VFD systems generate fields that can disrupt electrical devices. Ensure that these
fields are minimized and are not affecting the sensor.
Split-Core & Solid-Core On/Off Status Current Switches
FEATURES
DESCRIPTION
● More reliable for status than relays across auxiliary contacts
● Ideal for direct-drive units, unit vents, fan coil units, exhaust fans,
and other fixed loads
● Low 0.15 A turn-on (H300 and H600)...ideal for small exhaust
fans (not intended to detect belt loss)
● Removable mounting bracket provides installation flexibility
● Bracket on H900 can be installed in three different configurations...installer convenience
● Split-core H300, H600, and H900 for fast retrofit installation
● Mini solid-core H800 and micro split-core H300 fit in tight enclosures...saves valuable panel space
● 100% solid-state, no moving parts to fail
● Polarity insensitive output (except H800NC)
● 5-year warranty
Hawkeye x00 on/off current switches provide a cost-effective
solution for monitoring status on unit vents, exhaust fans,
recirculation pumps, and other fixed loads where belt loss
is not a concern.
Veris has applied new technology to the H300, H600, and H800
models to achieve impressive improvement in turn-on levels. The
Hawkeye H300 and H600 have the lowest turn-on current in
the industry at a mere 0.15 A!
APPLICATIONS
● Monitoring status of electrical loads
● Monitoring direct-drive units, exhaust fans, process
motors, and other fixed loads
● Verifying lighting run times and lighting status
● VFD output On/Off status
● Direct-Drive units, unit vents, fan coil units, exhaust fans, and
other fixed loads
HQ0001753.D 0115
TM
Current Monitoring
Hx00 Series
WIRING DIAGRAM
DIMENSIONAL DRAWINGS
H300
Unit Vent Heater Control
BUILDING AUTOMATION
CONTROLLER
POWER
SOURCE
H600
Removable Mounting Bracket
0.6"
(16 mm)
0.3”
(8 mm)
6 AWG max.
DI
Removable Mounting Bracket
Self-gripping Iris
1.6”
(40 mm)
DI
1.5”
(38 mm)
Ø 0.18” (x2)
(5 mm)
1.2"
0.7"
(31 mm)
(18 mm)
2.1"
(54 mm)
0.5"
(13 mm)
0.4” x 0.2”
(10 mm x 5 mm)
Slot (2x)
2.1"
(54 mm)
1.8”
(46 mm)
UNIT VENT HEATER
2.9"
(74 mm)
3.5"
(89 mm)
H900
H800, H800HV, H800NC
Removable Mounting Bracket
Removable/Adjustable Mounting Bracket
1.0”
(25 mm)
0.9"
(23 mm)
0 0.7"
(18 mm)
Self-gripping Iris
1.0"
(26 mm)
0.6”
(15 mm)
POWER
SOURCE
2.5" *
(64 mm)
1.1”
(26 mm)
3.1”**
(79 mm)
2.8" *
(71 mm)
0.8”
(21 mm)
Bracket can
be mounted
on three sides
for added
installation
flexibility.
Self-gripping Iris
2.8”
(70 mm)
1.7
(43 mm)
0.4” x 0.2”
Slot (x2)
1.4”*
(36 mm)
Ø 0.3”
(8 mm)
2.5”
(64 mm)
3.0”
(76 mm)
1.1" *
(27 mm)
2.3"
(58 mm)
* Terminal block may extend up to 1/8” over the height dimensions shown.
RoHS
ORDERING INFORMATION
Compliant
E150462
MODEL
AMPERAGE RANGE
@ 50/60 Hz only
STATUS OUTPUT
(Max.)
TRIP
POINT
HOUSING
UL
CE
ROHS
H300
0.15 - 60A
N.O. [email protected]/DC
0.15A or less
Split-core
n2
n
n
H600
0.15 - 200A
N.O. [email protected]/DC
0.15A or less
Split-core
n1
n
n
H800
0.25 -200A
N.O. [email protected]/DC
0.25A or less
Solid-core
n1
n
n
H800NC
0.5 - 200A
N.C. [email protected]
0.5A or less
Solid-core
n1
3
H800HV
0.75 - 200A
N.O. [email protected]/DC
0.75A or less
Solid-core
n
H900
1.5 - 200A
N.O. [email protected]/DC
1.5A or less
Split-core
n
n
1 Listed for use on 75°C insulated conductors.
2 Product provides functional insulation only.
3 Listed for use on 90°C insulated conductors.
n
ACCESSORIES
DIN Rail Clip Set (AH01 for H6xx, H8xx, H9xx;
AH27 for H3xx)
DIN Rail (AV01) and DIN Stop Clip (AV02)
HQ0001753.D 0115
800.354.8556
AH27
AV01
AH01
+1 503.598.4564
www.veris.com
AV02
HVAC Submittal Cover Sheet
SECTION: 3
PRODUCT: Humidifiers
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
Armstrong
Hill Company
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
P.O. Box 699
Roswell, Georgia 30077
Contractor Reg. No. CN003050
770-751-0850
770-751-0070 Facsimile
www.hillcompany.com
BBB
SUBMITTAL
FOR
Humidifiers H-1, H-2
Project:
Northside Facial Cosmetic Surgery
Alpharetta, GA
Mechanical Contractor
Paulson-Cheek Mechanical
6145 Northbelt Parkway
Norcross, GA 30071
Mechanical Engineer
AHA Consulting Engineers
1801 Old Alabama Road, Suite 125
Roswell, GA 30076
SUBMITTED BY:
HILL COMPANY, INC.
1305 Old Ellis Rd.
Roswell, GA 30076
[email protected]
Phone: 770 480-2328
www.hillcompany.com
March 17, 2015
industrial • institutional • commercial
Armstrong Humidifier
Two (2) Armstrong Humidifiers Complete with the following:
• Model HC-6100
o 208/1/60 voltage
o Capacity is 3 KW – 8.3 lbs/hr.
o Duct mounted dispersion tube for 14” wide x 14” high ductwork
o Duct mounted air proving switch
o Duct mounted high limit
o Temp-R-Drain Cooler
Notes:
1) Confirm duct size of 14” wide x 14” high
2) Verify voltage of 208/1/60
3) Confirm that humidifiers are served with tap water (not deionized water)
industrial • institutional • commercial
HumidiClean Series HC-6000 Humidifier
Revolutionary ionic bed technology that carries a lot of weight
The Ionic Bed. The Final Resting Place Of Ordinary Humidifiers.
Brace yourself. The Armstrong HumidiClean™ is going to
change everything you know about humidifiers. The process
starts with an extraordinary technology that will make
­traditional humidifiers obsolete. Leave them dead in their
tracks, you might say.
The ionic beds you see on this page are made of a fibrous
medium: the ionic bed. There are six such beds per tank
in a HumidiClean humidifier (more in the Models HC-6500
and HC-6700). They attract solids from the water as its
temperature rises – ­minimizing the buildup of solids on inner
tank walls and heating elements. So you have a humidifier
that stays clean except, of course, for the ionic beds. And
once they have absorbed their capacity of solids, the unit even
tells you to change them. It takes about 15 minutes and is
absolutely hassle free.
See For Yourself How Much HumidiClean Could Save
Over Traditional Units
As Table 118-1 illustrates, maintaining a HumidiClean with
­patented ionic bed technology is more economical than caring
for either traditional cleanable or non-cleanable electronic units.
When you combine costs for labor and materials and calculate
the differences for seasonal maintenance, the new Armstrong
HumidiClean is the obvious winner.
But to get an idea of just how big your advantage could be,
multiply your savings by the number of units you have and
­project your answer over a few years. Can you think of a better
reason to choose HumidiClean? We can’t either, but we can
think of several more reasons.
Table 118-1. Maintenance Cost Comparison
Maintenance cost comparison for a humidifying season using
Model HC-6100. Results may vary depending on your parts
and labor costs.
Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit armstronginternational.com for up-to-date information.
118
Armstrong International - NA
armstronginternational.com
Armstrong International - EU
armstronginternational.eu
Armstrong International - China
armstronginternational.cn
Armstrong International - India
armstronginternational.in
Armstrong International, Korea
armintl.co.kr
NEXT
HumidiClean Passes No Current Through Water
HumidiClean’s resistance-type design has a proven track
record for safety. Totally different compartments keep
plumbing ­completely separated from electrical components.
In addition, Armstrong has built several other safety features
into HumidiClean. These include a key-locked access door,
password protected programmable keypad, diagnostic
indicating LCD display, continual-checking diagnostic routines,
high- and low-water level detection, internal tank temperature
sensing, overcurrent protection and connections for a Class 2
alarm device.
HumidiClean uses submersed electric heating elements to
­generate steam. In other words, water quality or conductivity
do not affect the unit’s ability to generate full output on
demand. Although normally used with tap water, HumidiClean
can, upon request, be installed with deionized, demineralized,
softened or reverse osmosis water sources. Said another way:
You get the benefit of a humidifier capable of operating over
a wide range of water quality without frequent replacement of
parts or bothersome, messy cleaning.
Less Scale Means Greater Efficiency
Capacity is the first victim of the scale that quickly builds up
in traditional evaporative or steam-generating humidifiers. As
scale gathers in the pan or on heating elements or electrodes,
output declines. This gradually leads to a loss of humidity
control. From this point on, things get steadily worse – until
cleaning or the replacement of parts occurs.
HumidiClean with its remarkable ionic bed technology builds
up deposits on its ionic bed inserts instead of tank walls or
heating elements. As a result, it operates efficiently longer, its
tank stays cleaner longer, and it maintains nearly maximum
output throughout its service life.
HumidiClean Series HC-6000 Offers Enhanced
Control of Room RH
HumidiClean uses SCR controls as standard on all units
for full modulation of steam output. The humidifier’s
responsiveness to increased demand is enhanced through the
use of an aquastat to maintain a minimum water temperature
in the tank during short periods of no demand. The unit
also modulates fill of makeup water into the tank to prevent
reduction of steam output during the fill cycle for consistent
and responsive output of produced steam during the boil
down/fill cycle.
HumidiClean Communications Capability
HumidiClean Series HC-6000 offers native MODBUS
communications protocol as well as a Class II alarm circuit
for monitoring purposes. Optionally, HumidiClean may be
ordered to operate with either BACnet or LonWorks protocols.
Why Humidify?
As the temperature of indoor air goes up, its relative humidity
(RH) goes down. When RH falls to levels commonly found in
heated indoor environments, moisture-retaining materials such
as wood, paper, textile fibers and a wide range of food and
chemicals begin to deteriorate.
Dry air can also increase static electricity buildup, potentially
impacting production or the use of office equipment. Computer
rooms, printing operations, clean rooms and laboratories are
especially sensitive to static charges due to dry air. Low RH
also affects indoor air quality.
Steam is virtually a sterile medium offering many sanitation
benefits over other types of humidification. It is recommended
for essentially all commercial, institutional and industrial
­applications.
­­­­Ionic Bed Technology Saves Energy
Because of carbonate buildup, most humidifiers drain every
20-45 minutes. HumidiClean’s ionic beds attract these
­carbonates from water, so the primary reason to drain the tank
is to e
­ liminate sodium. Since this is typically only necessary
­approximately once every 12 hours, the unit wastes much less
hot water,thereby saving energy dollars.
Ionic Bed Technology
New ionic bed
After 400 hours
After 800 hours
These microscopic photos show how the ionic bed fibers (magnified 52.5X) collect solids throughout their service life.
A new ionic bed weighs approximately 1/3 pound. When it reaches its capacity, an ionic bed may weigh more than
2-1/2 pounds. A light on the control panel indicates when to replace HumidiClean’s beds.
Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit armstronginternational.com for up-to-date information.
Armstrong International - NA
armstronginternational.com
Armstrong International - EU
armstronginternational.eu
Armstrong International - China
armstronginternational.cn
Armstrong International - India
armstronginternational.in
Armstrong International, Korea
armintl.co.kr
119
NEXT
How HumidiClean Works
When power is supplied to the unit, the water fill valve
­energizes, and water enters the tank. Once the level reaches
the low-water switch, the heating elements are energized
(assuming there’s a call for steam output). The unit continues to
fill until the high-water switch is energized. The humidifier then
produces steam in response to the humidistat’s input signal.
The tank will fill at regular intervals if all conditions remain
­constant. Periodic tank drainage is based on active time of the
heating elements, but may be field-adjusted to water conditions.
The HumidiClean power module accepts a proportional signal
and, in response, pulses power to the heating elements to
­provide fully modulated output. Steam output is continuously
adjusted to satisfy necessary humidity requirements.
The standard HumidiClean includes the Armstrong modulating
control humidistat with a 0-10 Vdc control signal. The unit is
field-adjustable to accept any of the following common control
signals as the main control signal: on/off (SPST relay), 0-10
Vdc, 4-20 milliamp, 0-5 Vdc. Additional input t­erminals are
provided for on/off air flow and duct high-limit humidity controls.
Completing A Service Life Cycle
After the ionic beds have absorbed 90% of their capacity, the
LCD display will flash the “EOL” (end of life) message. (See
control panel photo.) If the HumidiClean is not s­ erviced by
replacing the ionic beds and re-setting the EOL, the unit will
continue to produce steam on demand for the remaining 10%
of ionic bed capacity. During this period, the unit will display
a flashing “EOL” message. After the ionic beds have reached
100% capacity, the unit will shut down by draining the tank
and will not respond to any call for humidity. Servicing the unit
is now required. The service life cycle is field-adjustable to
accommodate varying water quality and the specifics of the
individual application.
Simple Bed Removal
Toggle from “STEAM GENERATION” on the LCD to
“MANUAL DRAIN”. This will cause the unit to drain. When this
drain is complete, turn the main power off at the disconnect.
Use caution as tank will still be quite warm. Remove screws
from outer cover. Remove wingnuts from access panel.
Remove old beds by pulling them up and off the holding pins in
the tank, sliding them out through the access opening. Further
cleaning of the tank or heating element surface is typically not
required.
Install new beds in the same manner, sliding them through the
access panel and positioning them on the holding pins. After all
beds have been replaced, replace the tank access panel and
outer cover. Turn the power on at the main power d
­ isconnect.
Toggle to and reset EOL. Unit will fill with water and return to
normal operation. Total service time is u
­ sually no more than
15 minutes. (Used ionic beds contain no environmentally
hazardous material and may simply be thrown away.)
Drying Cycle
If there is no demand for steam for a c­ ontinuous 72-hour
­period, HumidiClean i­nitiates a routine to dry ionic beds by
draining and ­energizing the ­heating elements for short intervals.
This drying cycle ­eliminates standing water concerns and
improves indoor air quality.
Series HC-6000
Control Panel
The HumidiClean
­control panel is
designed to q
­ uickly
and simply ­display
operating ­conditions.
If an error is
detected, a
­diagnostic display
­indicates the ­specific
­condition.
Service As Easy As One, Two, Three
Step 1. Remove HumidiClean
­outer cover and remove tank
access panel. Remove the old
ionic bed inserts.
Step 2. Install new inserts in
place of the old ones.
Step 3. Reinstall tank access
panel and outer cover.
Restart HumidiClean.
Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit armstronginternational.com for up-to-date information.
120
Armstrong International - NA
armstronginternational.com
Armstrong International - EU
armstronginternational.eu
Armstrong International - China
armstronginternational.cn
Armstrong International - India
armstronginternational.in
Armstrong International, Korea
armintl.co.kr
NEXT
Selection and Ordering Procedure
using insulated copper tubing. The maximum recommended
­distance is 40 feet (12 meters) of equivalent length copper
­tubing. See Installation, Operation and Maintenance Bulletin
539 for additional guidelines.
Consider the following factors to select and order the
proper unit.
1.Compute the capacity required.
You must compute the maximum amount of moisture required to
determine that HumidiClean is properly sized for service.
For detailed information on calculating humidification loads,
refer to the Humidification Engineering section of this catalog or
Armstrong’s Humid-A-ware™ humidification sizing and selection
software. Both may be downloaded from Armstrong’s web site at
armstronginternaional.com. Humidification loads are generally
sized on a worst-case basis where design conditions exist for
a limited time and do not require a safety factor. HumidiClean
is designed to drain infrequently, because accumulation of
tank solids is not as problematic as with other humidifiers. This
­conserves water and energy. There will be a short period during
this drain cycle when there will be no steam output. Consult your
Armstrong Representative or the factory if this poses a control
problem for your system.
Example: Assume the humidification load is 38 lbs/hr (17.3 kg/
hr) and available power supply is 480 volt/3 phase. Referring
to Table 125-3, Page 125, we find a 15 kW Model HC-6100
HumidiClean is required. The branch circuit should be rated for
25 amps. See Table 125-2, Page 125.
1.Specify spare ionic bed inserts.
If HumidiClean is going to be in continuous service on a yearround basis, Armstrong recommends the purchase of a spare
set of beds.
Duct Unit
2.Specify steam dispersion tube (Table 121-1).
Select the proper steam dispersion tube that meets the duct
requirements. As an example, if the duct in which you are
installing the humidifier has a width between 17” and 22”,
you should use the steam dispersion tube(s) D-1.5 (DL-1.5 for
HC-6300, HC-6500 or HC-6700).
Alternatively, specify HumidiPack™ and indicate the following:
• Duct height and width
• CFM
• Duct air temperature
• Final duct RH%
• Non-wettable vapor distance available
• Maximum allowable air pressure drop (inches W.C.)
Figure 121-1. Dispersion Tube
2.Specify electrical characteristics of unit required.
Specify the voltage, kW, phase and cycles for unit on the order.
Determine total amperage for installation purposes.
For capacities to
40 lb/hr (18 kg/hr)
3.Specify the humidity level and range.
The standard Armstrong humidistat is 0-10 Vdc control and is
adjustable by a front-mounted dial from 5-95% RH. Specify room
or duct type humidistat. Or you may provide your own humidistat
and/or controller. If you are providing your own c­ ontroller,
specify control signal type.
4.Use proper connecting materials.
Two short hose cuffs per dispersion tube are provided to be
used with 2” (nom.) hard copper tube to connect the tank to the
steam dispersion tube (if applicable). Armstrong recommends
For capacities above
40 lb/hr (18 kg/hr)
Table 121-1. Selecting Proper Steam Dispersion Tube
Steam Disp. Tube Model
Steam Disp. Tube Model
All HC-6000 Series
DL-1
DL-1.5
DL-2
DL-3
DL-4
DL-5
DL-6
DL-7
DL-8
DL-9
DL-10
Duct Width
Min.
Weight
Max
in
mm
in
mm
in
mm
lb
kg
12
18
24
36
48
60
72
84
96
108
120
304
457
609
914
1219
1524
1829
2133
2438
2743
3048
11
17
23
35
47
59
71
83
95
107
119
279
432
584
889
1194
1499
1803
2108
2413
2718
3023
16
22
34
46
58
70
82
94
106
118
130
406
559
864
1168
1473
1778
2083
2388
2693
2998
3302
3
3
4
6
8
9
10
11
12
13
14
1.4
1.4
2
3
3.6
4
4.5
5
5.5
6
6.4
HC6300, HC6300DI, HC6500, HC6500DI, HC6700, HC6700DI Model “DL” Diameter is 2-3/8”.
Models HC-6500 and HC-6700 require a minimum of two (2) dispersion tubes).
Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit armstronginternational.com for up-to-date information.
Armstrong International - NA
armstronginternational.com
Armstrong International - EU
armstronginternational.eu
Armstrong International - China
armstronginternational.cn
Armstrong International - India
armstronginternational.in
Armstrong International, Korea
armintl.co.kr
121
NEXT
Selection and Ordering Procedure, continued…
1.Specify water source.
Specify if the service will include tap, deionized, demineralized,
softened or reverse osmosis water.
2.Specify options required.
• Duct high-limit humidistat. (Recommended). You may
order a duct high-limit stat. A typical setting for the high-limit
stat is 85% RH. Stat opens when relative humidity exceeds
settings. A modulating high-limit stat is also available for VAV
systems.
Figure 122-1. HC-6100 or HC-6300 Duct Type Distribution
Air
Flow
• Fan interlock. (Recommended). You may order a duct
­pressure switch to activate the humidifier by sensing
air flow in a duct system. The pressure switch prevents
humidifier operation if there is insufficient air movement in
the duct ­system.
Area Unit
1.Specify a fan package for each HumidiClean.
The EHF-3 offers a remote mounted, direct area discharge
option for use with HumidiClean (See Figure 122-3). EHF-3
offers capacities to 120 lbs/hr (54 kg/hr). A minimum of two
EHF-3 fan units are required for Model HC-6500 or HC-6700.
Please consult factory when applying EHF-3 fan package
with Model HC-6700.
Figure 122-4. HC-6100 or HC-6300 HumidiClean
Piped to HumidiPack
Air
Flow
10” Water Seal (min.)
Figure 122-2. HC-6100 or HC-6300 with
Duct Located below HumidiClean
6”
Min.
3/8” OD
Tubing “P” Trap
Figure 122-5. HC-6100 or HC-6300
General Installation Concept
Water Seal
Steam Piping 1”/12”
Pitch Piping Back
Figure 122-3. HC-6100 or HC-6300 with
EHF-3 Fan Package Mounted on Wall
4”
Min.
Duct
Dispersion
Tube
Close to
Main
Power
Disconnect
Valved Water
Supply
Maximum Piping Run 20 Feet
1”
1”
Pitch Drain Piping 1”/12”
on Horizontal Runs
Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit armstronginternational.com for up-to-date information.
122
Armstrong International - NA
armstronginternational.com
Armstrong International - EU
armstronginternational.eu
Armstrong International - China
armstronginternational.cn
Armstrong International - India
armstronginternational.in
Armstrong International, Korea
armintl.co.kr
NEXT
Specification
HumidiClean Series 6000
PART 1 PRODUCTS
STEAM GENERATOR TYPE HUMIDIFIERS
Steam humidifier for distribution of humidity (steam vapor) into air handling duct system shall be of the
self-contained, electrically controlled design.
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
Humidifier shall generate steam from ordinary tap water
Humidifier shall utilize disposable ionic bed inserts for tap water service to attract solids from
boiling water. Ionic beds assist in ensuring controllability through responsive and consistent
steam production regardless of water quality and minimize downtime required for tank
cleaning.
Humidifier shall have all internal components contained in a steel cabinet with key-locked
access doors to prevent unauthorized access.
Humidifier shall come standard with insulated painted tank enclosure.
Humidifier shall monitor tank operating history, and display will indicate when unit needs ionic
bed replacement. Service life cycle may be field adapted to match water quality.
Humidifier shall have SCR modulating control to provide 0%-100% of maximum capacity.
Humidifier is field adaptable to utilize onboard PID controller for use with 0-5Vdc, 0-10Vdc, 420mA sensors or can accept an input signal from external controller/humidistat (0-5Vdc, 010Vdc, 4-20mA or on/off).
Tank drain shall cycle based on operating history in order to conserve water and energy.
Drain cycle shall be field adjustable and drain will be tempered by the fill valve.
Humidifier includes end of season drain to empty tank during 72 hours of no demand. Tank
pitched to assist with complete drainage.
Unit shall monitor tank water level and will shut down power to the heating elements to
prevent unsafe operation upon failure of the drain system, fill system, or upon an overcurrent
condition
Humidifier shall utilize a thermal sensing device that senses temperature within a heating
element to prevent overheating.
Humidifier shall incorporate stainless steel conductance-actuated probes with Teflon
insulation for liquid level control on tap water service.
Humidifier shall include a password protected programmable keypad with backlit
alphanumeric display offering menu selectable diagnostics, ionic bed service life selection,
and tank drain program.
Keypad functions to include:
a. RH Graph of Previous 30 days of trend data.
b. Real Time Clock.
c. Error list log showing all previous errors experienced in past 30 days, timed stamped.
Humidifier fill water line shall have an air gap to prevent back-flow (siphoning) of tank water
into the potable water supply system
Humidifier shall modulate fill of makeup water into tank to prevent reduction of steam output
during fill cycle for consistent and responsive output of produced steam
Armstrong Humidification Group, 816 Maple Street, Three Rivers, MI 49093 – USA Phone: (269) 273-1415 Fax: (269) 273-9500
www.armstronginternational.com
Specification
P.
Q.
R.
S.
T.
U.
V.
A minimum tank temperature to be maintained during short periods of no demand through
use of an aquastat to improve responsiveness to increases of demand
Humidifier shall incorporate electrical terminals for installation of controlling stat/sensor, duct
high-limit stat/sensor, fan interlock switch, and Class 2 alarm device
Humidifier shall be supplied with integral Emergency Manual Stop for quick shut down.
Humidifier shall be supplied with stainless steel steam dispersion tube(s) which provide
uniform steam distribution over the entire tube length and shall be supplied at various lengths
(through 10’) to adequately span the widest dimension of the airstream.
Humidifier shall be supplied with hose cuffs for connection to hard copper tube (customer
supplied).
Humidifier tank shall be constructed of 14 ga. 304 stainless steel and the heating elements
shall include an incoloy sheath for tap water.
Humidifier is interoperable through native MODBUS communications protocol. Upon request,
humidifier may be supplied interoperable through BACnet or LonWorks communications
protocol.
Optional points:
1) Airflow proving switch shall be provided for field installation.
2) Duct mounted high limit humidistat shall be provided.
PART 3 EXECUTION
3.01 INSTALLATION
A. Install Armstrong humidifiers as indicated on drawings and as indicated in schedules in
accordance with manufacturer’s instructions.
Armstrong Humidification Group, 816 Maple Street, Three Rivers, MI 49093 – USA Phone: (269) 273-1415 Fax: (269) 273-9500
www.armstronginternational.com
HVAC Submittal Cover Sheet
SECTION: 4
PRODUCT: Grilles, Registers, & Diffusers
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
Nailor Industries
GAA
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
HVAC Submittal Cover Sheet
SECTION: 5
PRODUCT: Flexible Ductwork
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
ATCO
GAA
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
HVAC Submittal Cover Sheet
SECTION: 6
PRODUCT: Spin-In Dampers, Saddle Fittings, & Line Dampers
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
Jer-Air
GAA
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
HVAC Submittal Cover Sheet
SECTION: 7
PRODUCT: Fire Dampers
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
Nailor Industries
GAA
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
HVAC Submittal Cover Sheet
SECTION: 8
PRODUCT: Motor Operated Dampers
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
United Enertech
GAA
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
HVAC Submittal Cover Sheet
SECTION: 9
PRODUCT: Wall Louvers
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
United Enertech
GAA
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
HVAC Submittal Cover Sheet
SECTION: 10
PRODUCT: Exhaust Fans
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
Pennbarry
GAA
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
HVAC Submittal Cover Sheet
SECTION: 11
PRODUCT: Unit & Wall Heaters
Paulson-Cheek Mechanical, Inc.
6145 Norhtbelt Parkway, Suite F
Norcross, GA 30071
PROJECT: Northside Facial Cosmetic Surgery
PHONE: 770-729-0076
FAX:
770-729-1076
LOCATION: Alpharetta, GA
Paulson-Cheek Mechanical, Inc.
ARCHITECT'S/ENGINEER'S STAMP
Paulson-Cheek Mechanical, Inc.
DATE RECEIVED:
MANUFACTURER:
SUPPLIER:
SUBMITTED DATE:
X
03/25/15
Raywall
GAA
03/25/15
NO ERRORS DETECTED
CORRECT EXCEPTIONS NOTED
THIS APPROVAL OF SHOP DRAWINGS DOES
NOT RELIEVE THE SUBCONTRACTOR OR VENDOR
FROM THE REQUIREMENTS OF THE CONTRACT
DOCUMENTS.
CHECKED BY:
DATE CHECKED:
Submittal Section Sheet 3.25.15
Mark Walden
03/25/15
3/25/2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement