Graco 312065K - Reactor, Electric Proportioners Owner's Manual

Graco 312065K - Reactor, Electric Proportioners Owner's Manual

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Manual
Graco 312065K - Reactor, Electric Proportioners Owner's Manual | Manualzz
Operation
312065K
ENG
Electric, Heated, Plural Component Proportioner
For spraying polyurethane foam and polyurea coatings. For professional use only.
Not for use in explosive atmospheres.
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
See page 4 for model information, including maximum
working pressure and approvals.
Model E-XP1 Shown
Russian Patent No. 2359181
Taiwan Patent No. 1 303996
Australian Patent No. 2003291660
Other patents pending
TI10953a
Contents
Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Supplied Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Important Two-Component Material Information 10
Isocyanate Conditions . . . . . . . . . . . . . . . . . . . . 10
Material Self-ignition . . . . . . . . . . . . . . . . . . . . . 10
Keep Components A and B Separate . . . . . . . . 10
Moisture Sensitivity of Isocyanates . . . . . . . . . . 10
Foam Resins with 245 fa Blowing Agents . . . . . 11
Changing Materials . . . . . . . . . . . . . . . . . . . . . . 11
Typical Installation, with circulation . . . . . . . . . . 12
Typical Installation, without circulation . . . . . . . 13
Component Identification . . . . . . . . . . . . . . . . . . . 14
Temperature Controls and Indicators . . . . . . . . . 15
Main Power Switch . . . . . . . . . . . . . . . . . . . . . . 15
Red Stop Button . . . . . . . . . . . . . . . . . . . . . . . . 15
Actual Temperature Key/LED . . . . . . . . . . . . . . 15
Target Temperature Key/LED . . . . . . . . . . . . . . 16
Temperature Scale Keys/LEDs . . . . . . . . . . . . . 16
Heater Zone On/Off Keys/LEDs . . . . . . . . . . . . 16
Temperature Arrow Keys . . . . . . . . . . . . . . . . . . 16
Temperature Displays . . . . . . . . . . . . . . . . . . . . 16
Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . 16
2
Motor Controls and Indicators . . . . . . . . . . . . . . . 17
Motor ON/OFF Key/LED . . . . . . . . . . . . . . . . . . 17
PARK Key/LED . . . . . . . . . . . . . . . . . . . . . . . . . 17
PSI/BAR Keys/LEDs . . . . . . . . . . . . . . . . . . . . . 17
Pressure Key/LED . . . . . . . . . . . . . . . . . . . . . . . 17
Cycle Count Key/LED . . . . . . . . . . . . . . . . . . . . 17
Pressure Arrow Keys . . . . . . . . . . . . . . . . . . . . . 18
Pressure/Cycle Display . . . . . . . . . . . . . . . . . . . 18
Spray Adjustments . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Spraying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 32
Fluid Circulation . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Circulation Through Reactor . . . . . . . . . . . . . . . 33
Circulation Through Gun Manifold . . . . . . . . . . . 34
Jog Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Diagnostic Codes . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Temperature Control Diagnostic Codes . . . . . . . 36
Motor Control Diagnostic Codes . . . . . . . . . . . . 36
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Fluid Inlet Strainer Screen . . . . . . . . . . . . . . . . . 37
Pump Lubrication System . . . . . . . . . . . . . . . . . 38
Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 42
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 42
312065K
Systems
Systems
Part
Maximum Fluid
Working
Pressure
psi (MPa, bar)
Heated Hose
Gun
Proportioner
(see page 4)
50 ft (15 m) 10 ft (3 m) Model
Part
Mix
Chamber Kit
AP9024
2500 (17.2, 172)
259024
246679
246055
Fusion™ Air Purge
246100
AR2020
AP9025
2000 (13.8, 138)
259025
246678
246050
Fusion™ Air Purge
246101
AR5252
AP9026
2000 (13.8, 138)
259026
246678
246050
Fusion™ Air Purge
246101
AR5252
AP9028
3500 (24.1, 241)
259028
246679
246055
Fusion™ Air Purge
246100
AR2020
AP9029
2500 (17.2, 172)
259029
246679
246055
Fusion
Air Purge
246100
AR2020
AP9030
2000 (13.8, 138)
259030
246678
246050
Fusion™
Air Purge
246101
AR5252
AP9031
2000 (13.8, 138)
259031
246678
246050
Fusion™ Air Purge
246101
AR5252
AP9032
3500 (24.1, 241)
259032
246679
246055
Fusion™ Air Purge
246100
AR2020
AP9033
2500 (17.2, 172)
259033
246679
246055
Fusion™ Air Purge
246100
AR2020
AP9034
2000 (13.8, 138)
259034
246678
246050
Fusion™ Air Purge
246101
AR5252
AP9035
2000 (13.8, 138)
259035
246678
AP9036
3500 (24.1, 241)
259036
AP9057
2000 (13.8, 138)
259057
AP9058
2000 (13.8, 138)
AP9059
™
246050
™
Fusion
Air Purge
246101
AR5252
246679
246055
Fusion™
Air Purge
246100
AR2020
246678
246050
Fusion™
Air Purge
246101
AR5252
259058
246678
246050
Fusion™ Air Purge
246101
AR5252
2000 (13.8, 138)
259059
246678
246050
Fusion™ Air Purge
246101
AR5252
CS9025
2000 (13.8, 138)
259025
246678
246050
Fusion™ CS
CS01RD
CS9026
2000 (13.8, 138)
259026
246678
246050
Fusion™ CS
CS02RD
CS9030
2000 (13.8, 138)
259030
246678
246050
CS9031
2000 (13.8, 138)
259031
246678
246050
CS9034
2000 (13.8, 138)
259034
246678
246050
Fusion
CS9035
2000 (13.8, 138)
259035
246678
CS9057
2000 (13.8, 138)
259057
CS9058
2000 (13.8, 138)
CS9059
P29024
P29025
P29026
P29028
P29029
P29030
P29031
P29032
P29033
P29034
P29035
P29036
P29057
P29058
P29059
312065K
™
CS
CS01RD
™
CS
CS02RD
™
CS
CS01RD
246050
Fusion™ CS
CS02RD
246678
246050
Fusion™ CS
CS02RD
259058
246678
246050
Fusion™ CS
CS02RD
2000 (13.8, 138)
259059
246678
246050
2500 (17.2, 172)
2000 (13.8, 138)
2000 (13.8, 138)
3500 (24.1, 241)
2500 (17.2, 172)
2000 (13.8, 138)
2000 (13.8, 138)
3500 (24.1, 241)
2500 (17.2, 172)
2000 (13.8, 138)
2000 (13.8, 138)
3500 (24.1, 241)
2000 (13.8, 138)
2000 (13.8, 138)
2000 (13.8, 138)
259024
259025
259026
259028
259029
259030
259031
259032
259033
259034
259035
259036
259057
259058
259059
246679
246678
246678
246679
246679
246678
246678
246679
246679
246678
246678
246679
246678
246678
246678
246055
246050
246050
246055
246055
246050
246050
246055
246055
246050
246050
246055
246050
246050
246050
Fusion
Fusion
™
Fusion CS
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
Probler P2
CS02RD
GCP2RA
GCP2R1
GCP2R2
GCP2R0
GCP2RA
GCP2R1
GCP2R2
GCP2R0
GCP2RA
GCP2R1
GCP2R2
GCP2R0
GCP2R2
GCP2R2
GCP2R2
3
Models
Models
E-20 SERIES
Part, Series
Full Load Peak Voltage
Amps*
(phase)
259025, D
259030, D
259034, D
48
24
32
230V (1)
400V (3)
230V (3)
System
Watts†
Primary
Heater
Watts
Max Flow
Rate◆
lb/min
(kg/min)
Approximate
Output per Cycle Maximum Fluid
(A+B)
Working Pressure
gal. (liter)
psi (MPa, bar)
10,200
10,200
10,200
6,000
6,000
6,000
20 (9)
20 (9)
20 (9)
0.0104 (0.0395)
0.0104 (0.0395)
0.0104 (0.0395)
System
Watts†
Primary
Heater
Watts
Max Flow
Rate◆
lb/min
(kg/min)
Approximate
Output per Cycle Maximum Fluid
(A+B)
Working Pressure
gal. (liter)
psi (MPa, bar)
17,900
17,900
17,900
23,000
23,000
23,000
10,200
10,200
10,200
15,300
15,300
15,300
30 (13.5)
30 (13.5)
30 (13.5)
30 (13.5)
30 (13.5)
30 (13.5)
0.0272 (0.1034)
0.0272 (0.1034)
0.0272 (0.1034)
0.0272 (0.1034)
0.0272 (0.1034)
0.0272 (0.1034)
System
Watts†
Primary
Heater
Watts
Max Flow
Rate◆
gpm (lpm)
Approximate
Output per Cycle Maximum Fluid
(A+B)
Working Pressure
gal. (liter)
psi (MPa, bar)
15,800
15,800
15,800
10,200
10,200
10,200
1.0 (3.8)
1.0 (3.8)
1.0 (3.8)
0.0104 (0.0395)
0.0104 (0.0395)
0.0104 (0.0395)
System
Watts†
Primary
Heater
Watts
Max Flow
Rate◆
gpm (lpm)
Approximate
Output per Cycle Maximum Fluid
(A+B)
Working Pressure
gal. (liter)
psi (MPa, bar)
23,000
23,000
23,000
15,300
15,300
15,300
2.0 (7.6)
2.0 (7.6)
2.0 (7.6)
0.0203 (0.0771)
0.0203 (0.0771)
0.0203 (0.0771)
2000 (14, 140)
2000 (14, 140)
2000 (14, 140)
E-30 SERIES
Part,
Series
Full Load Peak Voltage
Amps*
(phase)
259026, D
259031, D
259035, D
259057, D
259058, D
259059, D
78
34
50
100
62
35
230V (1)
400V (3)
230V (3)
230V (1)
230V (3)
400V (3)
2000 (14, 140)
2000 (14, 140)
2000 (14, 140)
2000 (14, 140)
2000 (14, 140)
2000 (14, 140)
E-XP1 SERIES
Part, Series
Full Load Peak Voltage
Amps*
(phase)
259024, D
259029, D
259033, D
69
24
43
230V (1)
400V (3)
230V (3)
2500 (17.2, 172)
2500 (17.2, 172)
2500 (17.2, 172)
E-XP2 SERIES
Part,
Series
259028, D
259032, D
259036, D
Full Load Peak Voltage
Amps*
(phase)
100
35
62
230V (1)
400V (3)
230V (3)
3500 (24.1, 241)
3500 (24.1, 241)
3500 (24.1, 241)
* Full load amps with all devices operating at maximum
capabilities. Fuse requirements at various flow rates and
mix chamber sizes may be less.
◆ Maximum flow rate given for 60 Hz operation. For 50
† Total system watts, based on maximum hose length
Approvals:
Hz operation, maximum flow rate is 5/6 of 60 Hz maximum flow.
for each unit:
•
•
4
E-20 and E-XP1 series, 210 ft (64 m) maximum
heated hose length, including whip hose.
E-30 and E-XP2 series, 310 ft (94.5 m) maximum
heated hose length, including whip hose.
#ONFORMSTO!.3)5,
3TD#ERTIFIEDTO
#!.#3!3TD
#.O
312065K
Supplied Manuals
Supplied Manuals
Related Manuals
The following manuals are shipped with the Reactor™
Proportioner. Refer to these manuals for detailed equipment information.
The following manuals are for accessories used with the
Reactor™.
Order Part 15M334 for a compact disk of Reactor manuals translated in several languages.
Manuals are also available at www.graco.com.
Order Part 15M334 for a compact disk of Reactor manuals translated in several languages.
Reactor Data Reporting Kit
Part
Description
Reactor Electric Proportioner
309867
Instruction-Parts Manual (English)
Part
Description
Fusion Spray Gun
312066
Reactor Electric Proportioner,
Repair-Parts Manual (English)
Part
Description
309550
Instruction-Parts Manual (English)
Reactor Electrical Diagrams
Fusion CS Spray Gun
Part
Description
Part
Description
312067
Reactor Electric Proportioner,
Electrical Diagrams (English)
312666
Instruction-Parts Manual (English)
Proportioning Pump
Part
Description
309577
Electric Reactor Displacement Pump
Repair-Parts Manual (English)
Probler P2 Spray Gun
Part
Description
313213
Instruction-Parts Manual (English)
Heated Hose
Part
Description
309572
Instruction-Parts Manual (English)
Circulation and Return Tube Kit
Part
Description
309852
Instruction-Parts Manual (English)
Rupture Disk Assembly Kit
Part
Description
312416
Instruction-Parts Manual (English)
Electric Reactor Installation
312065K
Part
Description
310815
Instruction Manual (English)
5
Related Manuals
6
312065K
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where
applicable.
WARNING
ELECTRIC SHOCK HAZARD
This equipment must be grounded. Improper grounding, setup, or usage of the system can cause
electric shock.
• Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment.
• Connect only to grounded power source.
• All electrical wiring must be done by a qualified electrician and comply with all local codes and
regulations.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
•
•
•
Read MSDSs to know the specific hazards of the fluids you are using.
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
Always wear chemically impermeable gloves when spraying, dispensing, or cleaning equipment.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
• Gloves
• Hearing protection
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like
just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
• Engage trigger lock when not spraying.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking,
or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses and couplings daily. Replace worn or damaged parts immediately.
312065K
7
Warnings
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help
prevent fire and explosion:
•
•
•
•
•
•
•
•
•
Use equipment only in well ventilated area.
Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic
drop cloths (potential static arc).
Keep work area free of debris, including solvent, rags and gasoline.
Do not plug or unplug power cords, or turn power or light switches on or off when flammable
fumes are present.
Ground all equipment in the work area. See Grounding instructions.
Use only grounded hoses.
Hold gun firmly to side of grounded pail when triggering into pail.
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.
Keep a working fire extinguisher in the work area.
THERMAL EXPANSION HAZARD
Fluids subjected to heat in confined spaces, including hoses, can create a rapid rise in pressure due
to the thermal expansion. Over-pressurization can result in equipment rupture and serious injury.
•
•
Open a valve to relieve the fluid expansion during heating.
Replace hoses proactively at regular intervals based on your operating conditions.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious
chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious
injury, or property damage.
•
•
8
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents.
Many other fluids may contain chemicals that can react with aluminum. Contact your material
supplier for compatibility.
312065K
Warnings
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• This equipment is for professional use only.
• Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure in this manual when equipment is not in use.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in
all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine
manufacturer’s replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe
burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.
312065K
9
Important Two-Component Material Information
Important Two-Component Material Information
Isocyanate Conditions
Keep Components A and B
Separate
Spraying or dispensing materials containing isocyanates creates potentially harmful mists, vapors, and
atomized particulates.
Cross-contamination can result in cured material in
fluid lines which could cause serious injury or damage
equipment. To prevent cross-contamination of the
equipment’s wetted parts, never interchange component A (isocyanate) and component B (resin) parts.
Read material manufacturer’s warnings and material
MSDS to know specific hazards and precautions
related to isocyanates.
Prevent inhalation of isocyanate mists, vapors, and
atomized particulates by providing sufficient ventilation in the work area. If sufficient ventilation is not
available, a supplied-air respirator is required for
everyone in the work area.
To prevent contact with isocyanates, appropriate personal protective equipment, including chemically
impermeable gloves, boots, aprons, and goggles, is
also required for everyone in the work area.
Moisture Sensitivity of
Isocyanates
Isocyanates (ISO) are catalysts used in two component
foam and polyurea coatings. ISO will react with moisture
(such as humidity) to form small, hard, abrasive crystals,
which become suspended in the fluid. Eventually a film
will form on the surface and the ISO will begin to gel,
increasing in viscosity. If used, this partially cured ISO
will reduce performance and the life of all wetted parts.
Material Self-ignition
The amount of film formation and rate of crystallization varies depending on the blend of ISO, the
humidity, and the temperature.
To prevent exposing ISO to moisture:
Some materials may become self-igniting if applied
too thickly. Read material manufacturer’s warnings
and material MSDS.
•
•
•
•
•
•
10
Always use a sealed container with a desiccant
dryer in the vent, or a nitrogen atmosphere. Never
store ISO in an open container.
Keep the ISO lube pump reservoir (if installed) filled
with Graco Throat Seal Liquid (TSL), Part 206995.
The lubricant creates a barrier between the ISO and
the atmosphere.
Use moisture-proof hoses specifically designed for
ISO, such as those supplied with your system.
Never use reclaimed solvents, which may contain
moisture. Always keep solvent containers closed
when not in use.
Never use solvent on one side if it has been contaminated from the other side.
Always lubricate threaded parts with ISO pump oil
or grease when reassembling.
312065K
Important Two-Component Material Information
Foam Resins with 245 fa
Blowing Agents
Some foam blowing agents will froth at temperatures
above 90°F (33°C) when not under pressure, especially
if agitated. To reduce frothing, minimize preheating in a
circulation system.
312065K
Changing Materials
•
When changing materials, flush the equipment multiple times to ensure it is thoroughly clean.
•
Always clean the fluid inlet strainers after flushing.
•
Check with your material manufacturer for chemical
compatibility.
•
Most materials use ISO on the A side, but some use
ISO on the B side.
•
Epoxies often have amines on the B (hardener)
side. Polyureas often have amines on the B (resin)
side.
11
Typical Installation, with circulation
Typical Installation, with circulation
Key for FIG. 1
A
B
C
D
E
F
Reactor Proportioner
Heated Hose
Fluid Temperature Sensor (FTS)
Heated Whip Hose
Fusion Spray Gun
Gun Air Supply Hose
G
J
K
L
M
P
R
Feed Pump Air Supply Lines
Fluid Supply Lines
Feed Pumps
Agitator
Desiccant Dryer
Gun Fluid Manifold (part of gun)
Circulation Lines
M
K
K
R
L
J
G
A
F
J
D
B
E
R
P
C*
TI10976a
* Shown exposed for clarity. Wrap with tape during operation,
FIG. 1: Typical Installation, with circulation
12
312065K
Typical Installation, without circulation
Typical Installation, without circulation
Key for FIG. 2
A
B
C
D
E
F
G
Reactor Proportioner
Heated Hose
Fluid Temperature Sensor (FTS)
Heated Whip Hose
Fusion Spray Gun
Gun Air Supply Hose
Feed Pump Air Supply Lines
H
J
K
L
M
N
P
Q
K
Waste Containers
Fluid Supply Lines
Feed Pumps
Agitator
Desiccant Dryer
Bleed Lines
Gun Fluid Manifold (part of gun)
Air Filter/Separator
M
K
J
L
G
A
J
N
G
D
F
E
P
B
C*
H
TI10975a
* Shown exposed for clarity. Wrap with tape during operation,
FIG. 2: Typical Installation, without circulation
312065K
13
Component Identification
Component Identification
Key for FIG. 3
BA
BB
FA
FB
GA
GB
HA
HB
PA
PB
SA
SB
TA
TB
Component A Pressure Relief Outlet
Component B Pressure Relief Outlet
Component A Fluid Manifold Inlet (behind manifold block)
Component B Fluid Manifold Inlet
Component A Pressure Gauge
Component B Pressure Gauge
Component A Hose Connection
Component B Hose Connection
Component A Pump
Component B Pump
Component A PRESSURE RELIEF/SPRAY Valve
Component B PRESSURE RELIEF/SPRAY Valve
Component A Pressure Transducer (behind gauge GA)
Component B Pressure Transducer (behind gauge GB)
DG
EC
EM
FH
FM
FV
HC
MC
MP
RS
SC
SN
TC
Drive Gear Housing
Electrical Cord Strain Relief
Electric Motor
Fluid Heaters (behind shroud)
Reactor Fluid Manifold
Fluid Inlet Valve (B side shown)
Heated Hose Electrical Connector
Motor Control Display
Main Power Switch
Red Stop Button
Fluid Temperature Sensor Cable
Serial No. Plate
Temperature Control Display
TC
MC
RS
EM
DG
FH
GA
DG
TA
PA
GB
TB
SA
FM
FA
SB
BA
PB
HC
SC
FV
MP
FB
EC
BB
HA
HB
TI9880a
SN
TI10953a
TI7823a
FIG. 3: Component Identification (Model EXP-1 Shown)
14
312065K
Temperature Controls and Indicators
Temperature Controls and Indicators
NOTICE
To prevent damage to the softkey buttons, do
not press the buttons with sharp objects
such as pens, plastic cards, or fingernails.
Heater Power Indicators
Zone A Arrow Keys
A
Zone B Arrow Keys
B
Heater Displays
Heater A On/Off Key
Heater B On/Off Key
Hose Zone Arrow Keys
Hose Heater On/Off Key
°F
Actual Temperature Key
°C
Temperature Scale Keys
Target Temperature Key
FIG. 4. Temperature Controls and Indicators
Main Power Switch
Red Stop Button
Located on right side of unit, page 14. Turns Reactor
Located between temperature control panel and motor
power ON
control panel, page 14. Press
and OFF
heater zones or pumps on.
312065K
. Does not turn
to shut off motor
and heater zones only. Use main power switch to shut
off all power to unit.
15
Temperature Controls and Indicators
Actual Temperature Key/LED
Press
to display actual temperature.
Press and hold
Temperature Displays
Show actual temperature or target temperature of
heater zones, depending on selected mode. Defaults to
actual at startup. Range is 32-190°F (0-88°C) for A and
B, 32-180°F (0-82°C) for hose.
to display electrical current.
Circuit Breakers
Target Temperature Key/LED
Press
to display target temperature.
Press and hold
to display heater control circuit
board temperature.
Temperature Scale Keys/LEDs
Press
°F
or
°C
to change temperature scale.
Heater Zone On/Off Keys/LEDs
Press
Located inside Reactor cabinet.
Ref.
Size
Component
CB1
50 A
Hose/Transformer Secondary
CB2
40 A
Transformer Primary
CB3
25, 40*
Heater A
CB4
25, 40*
Heater B
CB5
20
Motor/Pumps
* Depending on model.
to turn heater zones on and off. Also clears
heater zone diagnostic codes, see page 36.
LEDs flash when heater zones are on. The duration
of each flash shows the extent that the heater is
turned on.
CB1
Temperature Arrow Keys
Press
, then press
or
perature settings in 1 degree increments.
16
to adjust tem-
CB2
CB3
CB4
ti9884a
CB5
For wiring and cabling, see repair manual 312066.
312065K
Motor Controls and Indicators
Motor Controls and Indicators
NOTICE
To prevent damage to the softkey buttons, do
not press the buttons with sharp objects
such as pens, plastic cards, or fingernails.
Pressure/Cycle Display
Arrow Keys
Motor ON/OFF Key
ON / OFF
PARK Key
Pressure Key
PARK
PSI/BAR Keys
Cycle Count Key
PSI
BAR
FIG. 5. Motor Controls and Indicators
Motor ON/OFF Key/LED
Pressure Key/LED
Press
Press
to turn motor ON and OFF. Also clears
to display fluid pressure.
some motor control diagnostic codes, see page 36.
PARK Key/LED
Press
at end of day to cycle component A pump
to home position, submerging displacement rod. Trigger
gun until pump stops. Once parked, motor will automatically shut off.
PSI/BAR Keys/LEDs
Press
312065K
PSI
or
BAR
If pressures are imbalanced, display shows higher
of two pressures.
Cycle Count Key/LED
Press
to display cycle count.
To clear counter, press and hold
for 3 sec.
to change pressure scale.
17
Spray Adjustments
Pressure Arrow Keys
Spray Adjustments
Press
Flow rate, atomization, and amount of overspray are
affected by four variables.
or
to adjust fluid pressure when
motor is ON. Setpoint displays for 10 sec.
When motor is OFF, pressing
To exit jog mode, press
•
Fluid pressure setting. Too little pressure results in
an uneven pattern, coarse droplet size, low flow,
and poor mixing. Too much pressure results in
excessive overspray, high flow rates, difficult control,
and excessive wear.
•
Fluid temperature. Similar effects to fluid pressure
setting. The A and B temperatures can be offset to
help balance the fluid pressure.
•
Mix chamber size. Choice of mix chamber is based
on desired flow rate and fluid viscosity.
•
Clean-off air adjustment. Too little clean-off air
results in droplets building up on the front of the
nozzle, and no pattern containment to control overspray. Too much clean-off air results in air-assisted
atomization and excessive overspray.
will enter jog mode.
until display shows
dashes or current pressure.
Pressure/Cycle Display
Shows fluid pressure or cycle count, depending on
mode selected.
Displays J 1 through J 10 when in jog mode, page 35.
18
312065K
Setup
Setup
Bolt bracket and mounting feet (MF) directly to
NOTICE
Proper system setup, start up, and shutdown procedures are critical to electrical equipment reliability.
The following procedures ensure steady voltage. Failure to follow these procedures will cause voltage fluctuations that can damage electrical equipment and
void the warranty.
truck or trailer bed. See page 40.
1. Locate Reactor
a. Locate Reactor on a level surface. SeeDimensions page 40, for clearance and mounting hole
dimensions.
b.
Do not expose Reactor to rain.
NOTICE
To prevent damage from tipping over and falling,
proper care needs to be taken when lifting the Reactor. Bolt Reactor to original shipping pallet, to keep
stable, before lifting.
c.
MF
Use the casters to move Reactor to a fixed location, or bolt to shipping pallet and move with
forklift.
d. To mount on a truck bed or trailer, remove casters and secure rear axle with 15B805 mobile
mounting bracket (MB), available separately.
MB
259024_312065
FIG. 6
2. General equipment guidelines
•
Determine the correct size generator. Using the correct size generator and proper air compressor will
enable the proportioner to run at a nearly constant
RPM. Failure to do so will cause voltage fluctuations
that can damage electrical equipment. Ensure the
generator matches the voltage and phase of the
proportioner.
Use the following procedure to determine the correct size generator.
a. List system components that use peak load
requirements in watts.
b.
Add the wattage required by the system components.
c.
Perform the following equation:
Total watts x 1.25 = kVA (kilovolt-amperes)
d. Select a generator size that is equal to or
greater than the determined kVA.
•
Use proportioner power cords that meet or exceed
the requirements listed in Table 2. Failure to do so
will cause voltage fluctuations that can damage
312065K
electrical equipment.
19
Setup
•
Use an air compressor with constant speed head
unloading devices. Direct online air compressors
that start and stop during a job will cause voltage
fluctuations that can damage electrical equipment.
•
Table 1: Electrical Requirements
(kW/Full Load Amps)
E SERIES
Maintain and inspect the generator, air compressor,
and other equipment per the manufacturer recommendations to avoid an unexpected shutdown.
Unexpected equipment shutdown will cause voltage
fluctuations that can damage electrical equipment.
•
Use a wall power supply with enough current to
meet system requirements. Failure to do so will
cause voltage fluctuations that can damage electrical equipment.
3. Electrical requirements
See TABLE 1.
Part No.
Model
Voltage
(phase)
259025
249030
259034
259026
259031
259035
259057
259058
259059
E-20
E-20
E-20
E-30
E-30
E-30
E-30†
E-30†
E-30†
230V (1)
400V (3)
230V (3)
230V (1)
400V (3)
230V (3)
230V (1)
230V (3)
400V (3)
Full
Load
Peak
Amps*
System
Watts**
48
24
32
78
34
50
100
62
35
10,200
10,200
10,200
17,900
17,900
17,900
23,000
23,000
23,000
69
24
43
100
35
62
15,800
15,800
15,800
23,000
23,000
23,000
E-XP SERIES
Installing this equipment requires access to parts
which may cause electric shock or other serious injury
if work is not performed properly. Have a qualified
electrician connect power and ground to main power
switch terminals, see page 21. Be sure your installation complies with all National, State and Local safety
and fire codes.
259024
259029
259033
259028
259032
259036
*
E-XP1
E-XP1
E-XP1
E-XP2
E-XP2
E-XP2
230V (1)
400V (3)
230V (3)
230V (1)
400V (3)
230V (3)
Full load amps with all devices operating at maximum capabilities. Fuse requirements at various flow
rates and mix chamber sizes may be less.
** E-20 and E-XP1 with 210 ft (64.1 m) hose; E-30 and
E-XP2 with 310 ft (94.6 m) hose.
† E-30 with 15.3 kW of heat.
20
312065K
Setup
4. Connect electrical cord
Power cord is not supplied. See Table 2.
a. 230V, 1 phase: Using 5/32 or 4 mm hex allen
wrench, connect two power leads to L1 and L2.
Connect green to ground (GND).
GND
Table 2: Power Cord Requirements
Part
Model
Cord Specification
AWG (mm2)
259024
259025
259026
259028
259029
259030
259031
259032
259033
259034
259035
259036
259057
259058
259059
E-XP1
E-20
E-30
E-XP2
E-XP1
E-20
E-30
E-XP2
E-XP1
E-20
E-30
E-XP2
E-30
E-30
E-30
4 (21.2), 2 wire + ground
6 (13.3), 2 wire + ground
4 (21.2), 2 wire + ground
4 (21.2), 2 wire + ground
10 (5.3), 4 wire + ground
10 (5.3), 4 wire + ground
8 (8.4), 4 wire + ground
8 (8.4), 4 wire + ground
8 (8.4), 3 wire + ground
8 (8.4), 3 wire + ground
6 (13.3), 3 wire + ground
6 (13.3), 3 wire + ground
4 (21.2), 2 wire + ground
6 (13.3), 3 wire + ground
8 (8.4), 4 wire + ground
L1
L2
ti2515b
b.
230V, 3 phase: Using 5/32 or 4 mm hex allen
wrench, connect three power leads to L1, L2,
and L3. Connect green to ground (GND).
GND
L1
L2
L3
ti3248b
c.
400V, 3 phase: Using 5/32 or 4 mm hex allen
wrench, connect three power leads to L1, L2,
and L3. Connect neutral to N. Connect green to
ground (GND).
GND
L1
L3
L2 N
ti2725a
312065K
21
Setup
5. Connect feed pumps
a. Install feed pumps (K) in component A and B
supply drums. See FIG. 1 and FIG. 2, pages 12
and 13.
a. Recommended: Connect high pressure hose
(R) to relief fittings (BA, BB) of both PRESSURE RELIEF/SPRAY valves, Route hose back
to component A and B drums. See FIG. 1, page
12.
b.
Seal component A drum and use desiccant
dryer (M) in vent.
SA
c.
Install agitator (L) in component B drum, if necessary.
BA
SB
R
R
d. Ensure A and B inlet valves (FV) are closed.
BB
b.
FV
TI10971a
Supply hoses from feed pumps should be 3/4 in.
(19 mm) ID.
6. Connect pressure relief lines
TI10954a
Alternately: Secure supplied bleed tubes (N) in
grounded, sealed waste containers (H). See
FIG. 2, page 13.
7. Install Fluid Temperature Sensor (FTS)
The Fluid Temperature Sensor (FTS) is supplied. Install
FTS between main hose and whip hose. See Heated
Hose manual 309572 for instructions.
8. Connect heated hose
See Heated Hose manual 309572 for detailed
instructions on connecting heated hoses.
Do not install shutoffs downstream of the PRESSURE
RELIEF/SPRAY valve outlets (BA, BB). The valves
function as overpressure relief valves when set to
SPRAY
. Lines must be open so valves can
The fluid temperature sensor (C) and whip hose (D)
must be used with heated hose, see page 22. Hose
length, including whip hose, must be 60 ft (18.3 m)
minimum.
automatically relieve pressure when machine is operating.
If circulating fluid back to the supply drums, use high
pressure hose rated to withstand the maximum working pressure of this equipment.
22
a. Turn main power OFF
b.
.
Assemble heated hose sections, FTS, and whip
hose.
312065K
Setup
c.
Connect A and B hoses to A and B outlets on
Reactor fluid manifold (FM). Hoses are color
coded: red for component A (ISO), blue for component B (RES). Fittings are sized to prevent
9. Close gun fluid manifold valves A and B
connection errors.
FM
HA
ti2411a
A
HB
10. Connect whip hose to gun fluid manifold
B
Do not connect manifold to gun.
TI10964a
Manifold hose adapters (HA, HB) allow use of 1/4
in. and 3/8 in. ID fluid hoses. To use 1/2 in. (13 mm)
ID fluid hoses, remove adapters from fluid manifold
and install as needed to connect whip hose.
d. Connect cables (Y). Connect electrical connectors (V). Be sure cables have slack when hose
bends. Wrap cable and electrical connections
with electrical tape.
ti2417a
11. Pressure check hose
See hose manual. Pressure check for leaks. If no leaks,
wrap hose and electrical connections to protect from
damage.
Y
V
TI10956a
312065K
23
Setup
12. Ground system
a. Component A (ISO) Pump: Keep reservoir (R)
filled with Graco Throat Seal Liquid (TSL), Part
206995. Wet-cup piston circulates TSL through
wet-cup, to carry away isocyanate film on displacement rod.
a. Reactor: is grounded through power cord. See
page 21.
b.
c.
Spray gun: connect whip hose ground wire to
FTS, page 22. Do not disconnect wire or spray
without whip hose.
R
Fluid supply containers: follow your local code.
d. Object being sprayed: follow your local code.
e. Solvent pails used when flushing: follow your
local code. Use only metal pails, which are conductive, placed on a grounded surface. Do not
place pail on a nonconductive surface, such as
paper or cardboard, which interrupts grounding
continuity
f.
TI3765a-2
FIG. 7
b.
To maintain grounding continuity when flushing
or relieving pressure, hold a metal part of spray
gun firmly to the side of a grounded metal pail,
then trigger gun.
13. Supply wet cups with Throat Seal Liquid
(TSL)
Component B (Resin) Pump: Check felt washers in packing nut/wet-cup (S) daily. Keep saturated with Graco Throat Seal Liquid (TSL), Part
No. 206995, to prevent material from hardening
on displacement rod. Replace felt washers
when worn or contaminated with hardened
material.
S
Pump rod and connecting rod move during operation.
Moving parts can cause serious injury such as pinching or amputation. Keep hands and fingers away from
wet-cup during operation. Turn main power OFF
TI3765a-1
before filling wet cup.
24
FIG. 8
312065K
Startup
Startup
NOTICE
Proper system setup, startup, and shutdown procedures are critical to electrical equipment reliability.
The following procedures ensure steady voltage. Failure to follow these procedures will cause voltage fluctuations that can damage electrical equipment and
void the warranty.
a. Check that all Setup steps are complete.
b.
Check that inlet screens are clean before daily
startup, page 37.
c.
Check level and condition of ISO lube daily,
page 37.
d. Turn on component B agitator, if used.
e. Turn both PRESSURE RELIEF/SPRAY valves
(SA, SB) to SPRAY
Do not operate Reactor without all covers and
shrouds in place.
.
SA
SB
1. Check generator fuel level.
Running out of fuel will cause voltage fluctuations
that can damage electrical equipment.
2. Ensure the main breaker on the generator is in the off position.
3. Start the generator. Allow it to reach full
operating temperature.
TI10963a
f.
Start feed pumps.
g. Open fluid inlet valves (FV). Check for leaks.
4. Close the bleed valve on the air compressor.
FV
5. Switch on the air compressor starter
and air dryer, if included.
6. Turn on power to the Reactor.
TI10972a
7. Load fluid with feed pumps
The Reactor is tested with oil at the factory. Flush
out the oil with a compatible solvent before spraying. See page 39.
312065K
25
Startup
8. Set temperatures
A
Do not mix components A and B during startup.
Always provide two grounded waste containers to
keep component A and component B fluids separate.
B
h. Use feed pumps to load system. Hold gun fluid
manifold over two grounded waste containers.
Open fluid valves A and B until clean, air-free
fluid comes from valves. Close valves.
°F
°C
Temperature Controls and Indicators, see page 15
ti2484a
This equipment is used with heated fluid, which can
cause equipment surfaces to become very hot. To
avoid severe burns:
•
Do not touch hot fluid or equipment.
•
Allow equipment to cool completely before touching it.
•
Wear gloves if fluid temperature exceeds 110°F
(43°C).
a. Turn main power ON
b.
Press
°F
or
°C
.
to change temperature
scale.
c.
26
Press
to display target temperatures.
312065K
Startup
A
d. To set
heat zone target temperature,
h. Hold
to view electrical currents for each
zone.
press
or
until display shows
desired temperature. Repeat for
B
i.
and
Hold
to view heater control circuit board
temperature.
zones.
For
j.
Manual current control mode only:
zone only, if FTS is disconnected at
startup, display will show hose current (0A). See
step j, page 27.
e. Press
to display actual temperatures.
When in manual current control mode, monitor hose
temperature with thermometer. Install per instructions
below. Thermometer reading must not exceed 160°F
(71°C). Never leave machine unattended when in
manual current control mode.
If FTS is disconnected or display shows diagnostic code E04, turn main power switch OFF
Do not turn on hose heat without fluid in hoses.
then ON
to clear diagnostic
code and enter manual current control mode.
f.
Turn on
heat zone by pressing
display will show current to hose. Current
.
Preheat hose (15-60 min). Indicator will flash
very slowly when fluid reaches target temperature. Display shows actual fluid temperature in
is not limited by target temperature.
Press
or
to adjust current setting.
hose near FTS.
Thermal expansion can cause overpressurization,
resulting in equipment rupture and serious injury,
including fluid injection. Do not pressurize system
when preheating hose.
To prevent overheating, install hose thermometer close to gun end, within operator view. Insert
thermometer through foam cover of A component hose so stem is next to inner tube. Thermometer reading will be about 20°F less than
actual fluid temperature.
If thermometer reading exceeds 160°F (71°C),
reduce current with
g. Turn on
ing
312065K
A
and
B
key.
heat zones by press-
for each zone.
27
Startup
9. Set pressure
10. Change pressure imbalance setting
(optional)
The pressure imbalance function (status code 24)
detects conditions that can cause off-ratio spray, such
as loss of feed pressure/supply, pump seal failure,
clogged fluid inlet filter, or a fluid leak.
ON / OFF
PARK
Code 24 (pressure imbalance) is set to an alarm as
the default. To change to a warning, see Reactor
Repair-Parts manual 312066.
PSI
BAR
Motor Controls and Indicators, see page 17
a. Press
b.
.
Press motor
. Motor and pumps start.
Display shows system pressure. Motor runs
until setpoint is reached.
c.
Press
or
The pressure imbalance default is factory-set at 500 psi
(3.5 MPa, 35 bar). For tighter ratio error detection, select
a lower value. For looser detection or to avoid nuisance
alarms, select a higher value.
a. Turn main power switch OFF
b.
until display shows
power switch ON
desired fluid pressure. Display will show setpoint for 10 seconds, then change to actual
pressure.
If display shows J xx, unit is in jog mode. To exit jog
mode, see page 35.
d. To display cycle count, press
To clear counter, press
.
and hold for 3 sec-
or
BAR
, then turn main
. Display will read
dP500 for psi or dP_35 for bar.
c.
If display pressure is greater than setpoint pressure, trigger gun to reduce pressure.
PSI
Press and hold
.
Press
or
to select desired pres-
sure differential (100-999 in increments of 100
psi, or 7-70 in increments of 7 bar). See Table 3.
Table 3: Available Pressure Imbalance Settings
PSI
BAR
100
200
300
400
*500
7
14
21
28
*35
PSI
600
700
800
900
999
BAR
42
49
56
63
69
* Factor default setting.
onds.
d. Turn main power switch OFF
e. Press
PSI
or
BAR
to change pressure
to save
changes.
scale.
28
312065K
Spraying
Spraying
3. Attach gun fluid manifold. Connect gun air line.
Open air line valve.
1. Engage gun piston safety lock.
ti2543a
ti2409a
4. Set PRESSURE RELIEF/SPRAY valves (SA, SB) to
2. Close gun fluid manifold valves A and B.
SPRAY
.
SA
SB
TI10963a
ti2728a
5. Check that heat zones are on and temperatures are
on target, page 26.
6. Press motor
to start motor and pumps.
7. Check fluid pressure display and adjust as necessary, page 29.
312065K
29
Spraying
8. Check fluid pressure gauges (GA, GB) to ensure
proper pressure balance. If imbalanced, reduce
pressure of higher component by slightly turning
PRESSURE RELIEF/SPRAY valve for that component toward PRESSURE RELIEF/CIRCULATION
9. Open gun fluid manifold valves A and B.
, until gauges show balanced pressures.
GA
GB
In this example, B side
pressure is higher, so
use the B side valve to
balance pressures.
ti2414a
On impingement guns, never open fluid manifold
valves or trigger gun if pressures are imbalanced.
TI10963a
10. Disengage gun piston safety lock.
ti2410a
11. Test spray onto cardboard. Adjust pressure and
temperature to get desired results.
12. Equipment is ready to spray.
30
312065K
Shutdown
Shutdown
NOTICE
Proper system setup, startup, and shutdown procedures are critical to electrical equipment reliability.
The following procedures ensure steady voltage. Failure to follow these procedures will cause voltage fluctuations that can damage electrical equipment and
void the warranty.
1. Shut off
A
B
,
4. Relieve pressure, page 32.
5. Turn off the air compressor and air dryer, if included.
6. Open air compressor bleed valve to relieve pressure
and remove water from tank.
7. Turn off the main breaker on the generator.
8. Allow generator dwell time, per manufacturer recommendations, prior to shutdown.
, and
heat zones.
9. Close both fluid supply valves (FV).
2. Park pumps.
a. Press
b.
.
Trigger gun until pump A stops in the retracted
position and the pressure of both pumps bleeds
down.
FV
ti10971a
10. Shut down feed pumps as required.
3. Turn main power OFF
312065K
.
31
Pressure Relief Procedure
Pressure Relief Procedure
fluid to waste containers or supply tanks. Ensure
gauges drop to 0.
1. Relieve pressure in gun and perform gun shutdown
procedure. See gun manual.
SA
SB
2. Close gun fluid manifold valves A and B.
TI10955a
5. Engage gun piston safety lock.
ti2421a
3. Shut off feed pumps and agitator, if used.
4. Turn PRESSURE RELIEF/SPRAY valves (SA, SB)
to PRESSURE RELIEF/CIRCULATION
32
. Route
ti2409a
6. Disconnect gun air line and remove gun fluid manifold.
312065K
Fluid Circulation
Fluid Circulation
Circulation Through Reactor
4. Turn main power ON
.
5. Set temperature targets, see page 26. Turn on
Do not circulate fluid containing a blowing agent without consulting with your material supplier regarding
fluid temperature limits.
To circulate through gun manifold and preheat hose, see
page 34.
A
and
Do not turn on
heat zones by pressing
.
heat zone unless hoses are
already loaded with fluid.
6. Press
1. Follow Startup procedures, page 25.
B
to display actual temperatures.
7. Circulate fluid in jog mode until
A
and
B
temperatures reach targets.
Do not install shutoffs downstream of the PRESSURE
RELIEF/SPRAY valve outlets (BA, BB). The valves
function as overpressure relief valves when set to
SPRAY
. Lines must be open so valves can
automatically relieve pressure when machine is operating.
2. See Typical Installation, with circulation, page
12. Route circulation lines back to respective component A or B supply drum. Use hoses rated at the
maximum working pressure of this equipment. See
Technical Data, page 41.
8. Turn on
heat zone by pressing
.
9. Set PRESSURE RELIEF/SPRAY valves (SA, SB) to
SPRAY
.
SA
SB
TI10963a
3. Set PRESSURE RELIEF/SPRAY valves (SA, SB) to
PRESSURE RELIEF/CIRCULATION
.
SA
SB
TI10955a
312065K
33
Fluid Circulation
Circulation Through Gun
Manifold
2. Route circulation lines back to respective component A or B supply drum. Use hoses rated at the
maximum working pressure of this equipment. See
Typical Installation, without circulation, page 13.
3. Follow Startup procedures, page 25.
Do not circulate fluid containing a blowing agent without consulting with your material supplier regarding
fluid temperature limits.
Circulating fluid through the gun manifold allows rapid
preheating of hose.
4. Turn main power ON
.
5. Set temperature targets, see page 26. Turn on
A
1. Install gun fluid manifold (P) on Part 246362 accessory circulation kit (CK). Connect high pressure circulation lines (R) to circulation manifold.
,
B
, and
heat zones by pressing
.
6. Press
to display actual temperatures.
7. Circulate fluid in jog mode until
P
CK
A
and
B
temperatures reach targets.
R
ti2767a
34
312065K
Jog Mode
Jog Mode
Jog mode has two purposes:
4. Press motor
•
It can speed fluid heating during circulation.
•
It can ease pump repair/replacement. See repair
manual.
5. Press
to start motor.
or
to change jog speed (J1
through J10).
1. Turn main power on
2. Ensure motor
.
is OFF (LED is off; display may
show dashes or pressure).
3. Press
312065K
Jog speeds correlate to 3-30% of motor power, but
will not operate over 700 psi (4.9 MPa, 49 bar) for
either A or B.
to select J1 (jog speed 1).
6. To exit jog mode, press
until display shows
dashes or current pressure.
35
Diagnostic Codes
Diagnostic Codes
Temperature Control Diagnostic Codes
Temperature control diagnostic codes appear on temperature display.
These alarms turn off heat. E99 clears automatically
when communication is regained. Codes E03 through
E06 can be cleared by pressing
turn main power OFF
. For other codes,
then ON
to clear.
Code
01
Code Name
Alarm Zone
High fluid temperature
Individual
02
High current
Individual
03
No current
Individual
04
FTS not connected
Individual
05
Board overtemperature
Individual
06
Loss of zone communication
Individual
30
Momentary loss of communication
All
99
Loss of display communication
All
See repair manual for corrective action.
For hose zone only, if FTS is disconnected at
startup, display will show hose current 0A.
Motor Control Diagnostic Codes
Motor control diagnostic codes E21 through E29 appear
on pressure display.
Warnings
There are two types of motor control codes: alarms and
warnings. Alarms take priority over warnings.
Reactor will continue to run. Press
See repair manual for corrective action.
warning will not recur for a predetermined amount of
time (varies for different warnings), or until main power
is turned OFF
Alarms
to clear. A
then ON
.
Alarms turn off motor and heat zones. Turn main power
OFF
then ON
to clear.
Alarms can also be cleared, except for code 23,
by pressing
36
.
Code
No.
Code Name
Alarm or Warning
21
No transducer (component A)
Alarm
22
No transducer (component B)
Alarm
23
High pressure
Alarm
24
Pressure imbalance
Selectable; see
repair manual
25
High line voltage
Alarm
26
Low line voltage
Alarm
27
High motor temperature
Alarm
28
High current
Alarm
29
Brush wear
Warning
312065K
Maintenance
Maintenance
Fluid Inlet Strainer Screen
•
Check wet cup TSL level daily.
•
Do not overtighten packing nut/wet cup. Throat
u-cup is not adjustable.
•
Inspect fluid inlet strainer screens daily, see below.
•
Grease circulation valves weekly with Fusion grease
(117773).
The inlet strainers filter out particles that can plug the
pump inlet check valves. Inspect the screens daily as
part of the startup routine, and clean as required.
Use clean chemicals and follow proper storage, transfer,
and operating procedures, to minimize contamination of
the A-side screen.
TI10955a
•
Inspect ISO lubricant level and condition daily, see
page 38. Refill or replace as needed.
•
Keep component A from exposure to moisture in
atmosphere, to prevent crystallization.
•
Clean gun mix chamber ports regularly. See gun
manual.
•
Clean gun check valve screens regularly. See gun
manual.
•
Use compressed air to prevent dust buildup on control boards, fan, motor (under shield), and hydraulic
oil coolers.
•
Keep vent holes on bottom of electrical cabinet
open.
Clean the A-side screen only during daily startup.
This minimizes moisture contamination by immediately flushing out any isocyanate residue at the
start of dispensing operations.
1. Close the fluid inlet valve at the pump inlet and shut
off the appropriate feed pump. This prevents material from being pumped while cleaning the screen.
2. Place a container under the strainer manifold (59d)
to catch fluid. Remove the strainer plug (59j).
3. Remove the screen (59g) from the strainer manifold.
Thoroughly flush the screen with compatible solvent
and shake it dry. Inspect the screen. If more than
25% of the mesh is blocked, replace the screen.
Inspect the gasket (59h) and replace as required.
4. Ensure the pipe plug (59k) is screwed into the
strainer plug (59j). Install the strainer plug with the
screen (59g) and gasket (59h) in place and tighten.
Do not overtighten. Let the gasket make the seal.
5. Open the fluid inlet valve, ensure that there are no
leaks, and wipe the equipment clean. Proceed with
operation.
59d
59g*
59h
59j
59k
Ti10974a
FIG. 9. Fluid Inlet Strainer
312065K
37
Maintenance
Pump Lubrication System
Check the condition of the ISO pump lubricant daily.
Change the lubricant if it becomes a gel, its color darkens, or it becomes diluted with isocyanate.
ST
RT
Gel formation is due to moisture absorption by the pump
lubricant. The interval between changes depends on the
environment in which the equipment is operating. The
pump lubrication system minimizes exposure to moisture, but some contamination is still possible.
RB
LR
Lubricant discoloration is due to continual seepage of
small amounts of isocyanate past the pump packings
during operation. If the packings are operating properly,
lubricant replacement due to discoloration should not be
necessary more often than every 3 or 4 weeks.
TI10970a
To change pump lubricant:
1. Relieve pressure, page 32.
2. Lift the lubricant reservoir (LR) out of the bracket
(RB) and remove the container from the cap. Holding the cap over a suitable container, remove the
check valve and allow the lubricant to drain. Reattach the check valve to the inlet hose. See FIG. 10.
3. Drain the reservoir and flush it with clean lubricant.
RT
ST
LR
4. When the reservoir is flushed clean, fill with fresh
lubricant.
5. Thread the reservoir onto the cap assembly and
place it in the bracket.
6. The lubrication system is ready for operation. No
priming is required.
TI10969a
FIG. 10. Pump Lubrication System
38
312065K
Flushing
Flushing
•
To flush feed hoses, pumps, and heaters separately
from heated hoses, set PRESSURE
RELIEF/SPRAY valves (SA, SB) to PRESSURE
RELIEF/CIRCULATION
lines (N).
Flush equipment only in a well-ventilated area. Do not
spray flammable fluids. Do not turn on heaters while
flushing with flammable solvents.
. Flush through bleed
SA
SB
N
•
Flush out old fluid with new fluid, or flush out old
fluid with a compatible solvent before introducing
new fluid.
•
Use the lowest possible pressure when flushing.
•
All fluid components are compatible with common
solvents. Use only moisture-free solvents.
N
TI10955a
•
To flush entire system, circulate through gun fluid
manifold (with manifold removed from gun).
•
To prevent moisture from reacting with isocyanate,
always leave the system dry or filled with a moisture-free plasticizer or oil. Do not use water. See
page 10.
Accessories
Feed Pump Kits
Heated Hoses
Pumps, hoses, and mounting hardware to supply fluids
to Reactor. Includes 246483 Air Supply Kit. See
309815.
50 ft (15.2 m) and 25 ft (7.6 m) lengths, 1/4 in. (6 mm),
3/8 in. (10 mm), or 1/2 in. (13 mm) diameter, 2000 psi
(14 MPa, 140 bar) or 3500 psi (24 MPa, 241 bar). See
309572.
246483 Air Supply Kit
Hoses and fittings to supply air to feed pumps, agitator,
and gun air hose. Included in feed pump kits. See
309827.
Heated Whip Hoses
10 ft (3 m) whip hose, 1/4 in. (6 mm) or 3/8 in. (10 mm)
diameter, 2000 psi (14 MPa, 140 bar) or 3500 psi (24
MPa, 241 bar). See 309572.
246978 Circulation Kit
Return hoses and fittings to make circulation system.
Includes two 246477 Return Tube Kits. See 309852.
Fusion Spray Gun
Air purge gun, available in round or flat pattern. See
309550.
246477 Return Tube Kit
Desiccant dryer, return tube, and fittings for one drum.
Two included in 246978 Circulation Kit. See 309852.
248669 Conversion Kit
Convert any E-XP2 to a E-30 with 15.3kW of heat.
Include new pumps, bearing, and fitting to accomplish
conversion. See manual 309574.
246085 Data Reporting Kit
Records actual temperature, temperature setpoint,
actual pressure, cycles, and diagnostic code data from
Reactor. Downloads data to PC with Microsoft® Windows 98 or later. See 309867.
248848 Data Reporting Kit
Records actual temperature, temperature setpoint,
actual pressure, cycles, and diagnostic code data from
Reactor. Downloads data to PC with Microsoftâ Windows 98 or later. Does not include interface module. See
309867.
312065K
39
Dimensions
Dimensions
Dimension
A
B
C
in. (mm)
46.0 (1168)
31.0 (787)
33.0 (838)
A
C
B
40
TI10953a
312065K
Technical Data
Technical Data
Category
Maximum Fluid Working Pressure
Data
Models E-20 and E-30: 2000 psi (14 MPa, 140 bar)
Model E-XP1: 2500 psi (17.2 MPa, 172 bar)
Maximum Fluid Temperature
Maximum Output
Model E-XP2: 3500 psi (24.1 MPa, 241 bar)
190°F (88°C)
Model E-20: 20 lb/min (9 kg/min)
Model E-30: 30 lb/min (13.5 kg/min)
Model E-XP1: 1 gpm (3.8 liter/min)
Output per Cycle (A and B)
Model E-XP2: 2 gpm (7.6 liter/min)
Model E-20 and E-XP1: 0.0104 gal. (0.0395 liter)
Model E-30: 0272 gal. (0.1034 liter)
Line Voltage Requirement
Model E-XP2: 0.0203 gal. (.0771 liter)
Parts 259024, 259025, 259026, 259028, 259057: 195-264 Vac, 50/60 Hz
Parts 259029, 259030, 259031, 259032, 259059: 338-457 Vac, 50/60 Hz
Amperage Requirement
Heater Power
Parts 2590330, 259034, 259035, 259036, 259058: 195-264 Vac, 50/60 Hz
See Table 1, page 19.
Model E-20: 6000 Watts
Model E-30 and E-XP1: 10200 Watts
Sound Power, per ISO 9614-2
Models E-XP2 and E-30 with 15.3kW of heat: 15300 Watts
Model E-20: 80 dB(A) at 2000 psi (14 MPa, 140 bar), 0.5 gpm (1.9 lpm)
Model E-30: 93.5 dB(A) at 1000 psi (7 MPa, 70 bar), 3.0 gpm (11.4 lpm)
Model E-XP1: 80 dB(A) at 2000 psi (14 MPa, 140 bar), 0.5 gpm (1.9 lpm)
Model E-XP2: 83.5 dB(A) at 3000 psi (21 MPa, 210 bar), 1.0 gpm (3.8 lpm)
Sound Pressure, 1 m from equipment Model E-20: 70.2 dB(A) at 2000 psi (14 MPa, 140 bar), 0.5 gpm (1.9 lpm)
Model E-30: 83.6 dB(A) at 1000 psi (7 MPa, 70 bar), 3.0 gpm (11.4 lpm)
Model E-XP1: 70.2 dB(A) at 2000 psi (14 MPa, 140 bar), 0.5 gpm (1.9 lpm)
Fluid Inlets
Fluid Outlets
Model E-XP2: 73.6 dB(A) at 3000 psi (21 MPa, 210 bar), 1.0 gpm (3.8 lpm)
3/4 npt(f), with 3/4 npsm(f) union
Component A (ISO): #8 (1/2 in.) JIC, with #5 (5/16 in.) JIC adapter
Fluid Circulation Ports
Weight
Component B (RES): #10 (5/8 in.) JIC, with #6 (3/8 in.) JIC adapter
1/4 npsm(m), with plastic tubing; 250 psi (1.75 MPa, 17.5 bar) maximum
Model E-20 and E-XP1: 342 lb (155 kg)
Model E-30: 400 lb (181kg)
Wetted Parts
Models E-XP2 and E-30 with 15.3kW of heat: 438 lb (198 kg)
Aluminum, stainless steel, zinc plated, carbon steel, brass, carbide, chrome,
chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
312065K
41
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211, Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original Instructions. This manual contains English. MM 312065
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2007, Graco Inc. is registered to ISO 9001
www.graco.com
Revised 09/2010

advertisement

Related manuals

Download PDF

advertisement