Instruction Sheet

TOR SERIES

TOR-X-20RP

Flush Mount tilt out wall rack

UL

LISTED

THANK YOU

Thank you for purchasing the TOR-X-20RP Flush Mount. Please read these instructions thoroughly before installing / assembling this product.

PRODUCT FEATURES

- Convenient tip-out design allows easy access to equipment controls

- Rackrail is included for use with rackmount equipment

- Mount non-rackmount equipment using included clamp bars

I-00106 Page 1 Rev E

ASSEMBLY

TOOLS:

- Socket wrench set

- Power drill and bit set

1) Construct a rough opening - 24.75" W x 30.312" H:

2 space - 2 x 4

3 space - 2 x 4 for partial, 2 x 6 for flush

4 space - 2 x 4, 2 x 6 for partial, 2 x 8 for flush

2) Disassembly is required prior to mounting.

Open the door on the faceplate. To do this, the

door must be slightly lifted and opened to the service

position (105 0 ). (FIGURE A)

FIGURE B

BACKPAN

FACE

PLATE

DECORA STYLE

KNOCKOUT

ROTATE

FIGURE A

LIFT

3) Remove the six nuts that secure the

faceplate to the backpan and remove

the faceplate. (FIGURE B)

NOTE: If using with the partial recess trim

kit (TOR-PRT), see Instruction Sheet

I-00107. (optional accessory)

CLAMP

UCP

PANEL

FIGURE C

MOUNTING

HOLES

4) Using the customer supplied mounting hardware

specified below, mount the backpan into the wall.

(FIGURE C)

Block Wall Installation:

1) 5/8" pilot hole

2) 1/4" X 2" toggle bolt and washer

Wood Stud Wall Installation:

1) 1/8" pilot hole in center of stud

2) 1/4" X 2" lag bolt and washer

5) Re-assemble the faceplate to the backpan by re-using

the six nuts. (FIGURE B)

I-00106 Page 2

CLAMP ASSEMBLY:

Choose a desired location for the clamp and assemble the clamp to the ears using the screws and nuts provided (FIGURE D). Slide the clamp brackets securely down on the equipment and tighten. Adjust the stop bars to secure the rear of the equipment and tighten.

FIGURE D

CLAMP

BRACKETS

STOP

BARS

EARS

CONNECTION OF THE BONDING WIRE:

Install the bonding wire as shown using the wire and the nuts provided.

OPTIONAL ACCESSORY: UNIVERSAL CONNECTOR PANEL

For Middle Atlantic Products UCP modules (used to mount commonly used connectors), see

surface of the faceplate.

I-00106 Page 3

WARRANTY

Middle Atlantic Products, Inc. (the "Company") warrants the TOR-X-20RP Flush Mount to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product.

The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection thereof at the Company's factory.

This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly, installation or maintenance.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY

BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE

PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)

HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS

PAID TO THE COMPANY.

Corporate Headquarters

Corporate Voice 973-839-1011 - Fax 973-839-1976

International Voice +1 973-839-8821 - Fax +1 973-839-4982 middleatlantic.com - [email protected]

Middle Atlantic Canada

Voice 613-836-2501 - Fax 613-836-2690 middleatlantic.ca - [email protected]

Factory Distribution

USA: NJ - CA - IL Canada: ON - BC

At Middle Atlantic Products we are always listening. Your comments are welcome.

Middle Atlantic Products is an ISO 9001 Registered Company

I-00106 Page 4 30% Recycled Paper

Instruction Sheet

TOR SERIES

TOR-PRT Partial Recess Trim Kit

For Tilt Out Wall rack

TOOLS REQUIRED

# 2 Phillips Driver

NOTE: The trim provides aesthetic improvements

when used on partially recessed

applications.

UL

LISTED

BACKPAN

FASCIA

FIGURE A

ASSEMBLY

The assembly should coincide with initial installation of the product. (Instruction Sheet I-00106)

NOTE: The flange from the faceplate should be removed. Take out the six (6) screws from the

back of the faceplate and remove.

1) Place the fascia on the backpan and slide on the backpan until it is flush with the wall.

(fascia will be sandwiched between the side of backpan and the wall stud)

2) Install the six (6) customer supplied mounting screws through the backpan side and

fascia, do not tighten. (FIGURE A)

3) While pressing on the fascia face until it’s completely flush with the wall, tighten the

mounting screws.

TIP: Tighten the alternate corners first, followed by the center screws.

I-00107 Page 1 Rev D

WARRANTY

Middle Atlantic Products, Inc. (the "Company") warrants the TOR-PRT Partial Recess Trim

Kit to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product.

The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection thereof at the Company's factory.

This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly, installation or maintenance.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY

BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE

PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)

HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS

PAID TO THE COMPANY.

Corporate Headquarters

Corporate Voice 973-839-1011 - Fax 973-839-1976

International Voice +1 973-839-8821 - Fax +1 973-839-4982 middleatlantic.com - [email protected]

Middle Atlantic Canada

Voice 613-836-2501 - Fax 613-836-2690 middleatlantic.ca - [email protected]

Factory Distribution

USA: NJ - CA - IL Canada: ON - BC

At Middle Atlantic Products we are always listening. Your comments are welcome.

Middle Atlantic Products is an ISO 9001 Registered Company.

I-00107 Page 2

30% Recycled Paper