Bartell DMC6D Drill Owner's Manual
Below you will find brief information for Diamond Core Drill D-Handle Model, Diamond Core Drill Pistol-Handle Model, Diamond Core Drill Constant Speed Model. These diamond core drilling machines are designed for drilling concrete, masonry, and stone. The D-Handle and Pistol-Handle models are suitable for hand-held drilling up to 80mm. For sizes above, rig mounting is required. The Constant Speed model is designed with water feed for diamond core drilling. The machines feature a mechanical gearbox, mechanical safety clutch, overload protection, and thermal protection..
PDF
Download
Document
Advertisement
Advertisement
Original instructions CAUTION: Machine equipped with overheat thermal protec tion. When the thermal protection kicks in, always remove from the worpiece and run at no load for at least 3 minutes to allow motor to co ol b efore returning to operation. Model D-Handle Model Pistol-Handle Model Power Input 220-240V: 2000W, 110-120V: 1700W Voltage See machine nameplate No Load min-1 930 / 1520 / 4270 Rated Load min-1 560 / 910 / 2560 Capacity-Wet (Hand-Held) 80mm (3") Capacity-Wet (Rig-Mounted) 162mm (6-1/4") Capacity-Dry (Convertible Models Only) 182mm ( 7-1/4") Arbor Thread 1-1/4"UNC & 1/2" BSP Neck Diameter 60mm Dimensions 528mm X 106mm X 145mm 437mm X 115mm X 289mm Net Weight 6.4kg (14 Lbs.) 6.4kg (14 Lbs.) D-Handle Model Gear Selector Tubular Spirit Level Constant Speed Model 220-240V: 2500W, 110-120V: 2300W 480 / 1050 / 2200 480 / 1050 / 2200 202mm (8") n/a 463mm x 127mm x 310mm 7.3kg (16 Lbs) Indicator Light Spindle 1-1/4"UNC &, 1/2"BSP Lock Button Trigger Switch Main Handle Side Handle Assy. Bull's Eye Level Water Feed Valve Quick-Release Water Coupling Pistol-Handle Model Side Handle Lock Screw Tubular Spirit Level Spindle 1-1/4"UNC &, 1/2"BSP Lock Button Gear Selector Trigger Switch Bull's Eye Level Main Handle Quick-Release Water Coupling 2 Indicator Light Constant Speed Model Side Handle Lock Screw Release Button Spindle 1-1/4" UNC & 1/2"BSP Side Handle Assy. Lock Button Gear Selector Trigger Switch Main Handle Water Feed Valve Indicator Light Bull's eye Level Convertible Models Port Water Feed Adaptor Head Vacuum Adaptor Head Water Feed Valve Coupling 3 GENERAL SAFETY INSTRUCTIONS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool. 1) Work area safety a. b. c. Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical safety a. b. c. d. e. f. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a. b. c. d. e. f. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves 4 g. away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) Power tool use and care a. b. c. d. e. f. g. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Service Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Symbols used in this manual V…….......volts A…….......amperes Hz……......hertz W……......watt ~………....alternating current .......read these instructions ......always wear eye protection n0………..no load speed ......always wear a dust mask. min-1….....revolutions or reciprocation per minute ......warning of general danger .....always wear hearing protection .....wear safety-approved hard hat .…with electrical earth do not dispose of electric tools, accessories and packaging together with household waste material 5 DRILL SAFETY WARNINGS • • • • • • • • • • • • • • • Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. NOTE The above warning applies only to impact drills and may be omitted for drills other than impact drills. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. The locking screw for the ground/earth cable may never be loosened, otherwise there is acute danger to life! Check the ground (earth) connection of the electrical plug. Never use the machine without the PRCD fault-current safety switch supplied. Always check the PRCD fault-current safety switch for correct functioning before starting a drilling operation. Ensure that no water is allowed to get into the motor unit during operation. If you detect a leak in any part of the water supply system, shut the machine down immediately and repair the fault. Water pressure should not exceed 70 psi (4 bar). Take care not to damage gas, water, power and other conduits in the area of the drilling operation. Drain or shut off these conduits as required. Block off the working area and place warning signs on both sides of the wall when drilling through from one side to the other. Take appropriate precautions to ensure that, in the event of a drilling core dropping out, no personal injury or material damage will result. When drilling hollow components, check the flow route of the cooling water in order to prevent damage. Always hold the machine tightly. Diamond core drilling bits can become stuck at any time during core drilling, there is a danger of the machine jumping out of control. WARNING: Pull the plug out of the socket before making device settings or changing accessories. Many accidents are caused by accidental starting of power tools. WARNING! 110V UK machines are not equipped with a PRCD portable residual current device or GFCI ground fault circuit interrupter. The machine must always be used with an isolating transformer for protection in case an electrical fault should occur. INTRODUCTION The machine is equipped with spirit levels which aid in aligning the tool. By positioning the machine so that the bubble is in the center of the window one can drill a straight hole. Use the Bull's Eye Level for vertical aligning and the Tubular Level for horizontal aligning. This machine is for the intended purpose of diamond core drilling of concrete, masonry, stone and similar materials. The machine may be hand-held for drilling up to 80mm. For sizes above 80mm, it must be mounted on a rig (drilling stand). The rig is not included. All other uses which are not for the intended purpose are prohibited. It is equipped with a water feed system which is required for the diamond core drilling process. 6 (Convertible models also have two adaptor heads; one for water feed and one for through-the-spindle dust aspiration). It is equipped with a PRCD interrupter (portable residual current device) which must be used at all times. It is equipped with a three speed mechanical gearbox for different core drill size ranges and features a mechanical safety clutch. The motor has electronics for soft start, overload protection and thermal (overheating) protection. There is an indicator light on the machine to alert the operator of load and temperature conditions. ELECTRICAL CONNECTION The network voltage must conform to the voltage indicated on the tool name plate. Under no circumstances should the tool be used when the power supply cable is damaged. A damaged cable must be replaced immediately by an authorized Customer Service Center. Do not try to repair the damaged cable yourself. The use of damaged power cables can lead to an electric shock. WARNING: This machine is equipped with a Portable Residual Current Device (PRCD) also known as a Ground Fault Circuit Interrupter (GFCI). Always use this device whenever using the machine to reduce the risk of shock hazards. Always position the device PRCD as close as possible to the power source. Test and reset the PRCD device before each use. Press the “Test” button to test. Press the “Reset” button to energize the circuit to the machine. WARNING!: 110V UK machines are not equipped with a PRCD portable residual current device or GFCI ground fault circuit interrupter. The machine must always be used with an isolating transformer for protection in case an electrical fault should occur. Use an RCD in a separate control box with one or more socket outlets in accordance with EN 60309-2 with the earthing contact position 1 h. On Lamp Test Button Reset Button WARNING: Always connect the plug into the wall socket with a drip loop. If the cable leads downward directly into the wall socket, any water on the cable could run into the socket, causing a hazard. ASSEMBLY 1. 2. 3. Mount the handle clamp of the side handle onto the gearbox neck. Position the side handle perpendicular to the main handle. Use the lock screw to tighten the clamp. Thread the water supply assy. Into the hole in the bottom of gearbox and tighten with a wrench. For convertible models: insert either the water feed adaptor head or the vacuum adaptor head into the port. 7 LIST OF CONTENTS • • • • Diamond core drilling machine. Side handle assembly Water feed assembly Wrench (Convertible models only:) • Water feed adaptor head • Vacuum adaptor head OPERATING INSTRUCTIONS 1) MOUNTING THE CORE BIT CAUTION: Ensure that the threads of the spindle and the core bit match. Attempting to mount mismatched threads will result in damage to both threads. The spindle has two types of threads. The outside male thread is 1-1/4inch UNC, the inside female thread is 1/2 inch BSP. Ensure both the core bit and the machine spindle are clean. Any debris could cause excessive run-out of the mounted core bit. Excessive run-out can cause premature failure of the core bit and/or a safety hazard. Tighten the bit to the spindle using two wrenches. Only use correct sized wrenches to avoid damage to the spindle or bit. Choosing the correct core bit for the job: Ensure that the bit you are using is suitable for the material you are drilling. There are two main types of diamond core bit: Wet/dry type-electroplated (surface set) diamond core bits and wet type-sintered (impregnated) diamond core bits. We recommend always using wet-type (sintered) bits with this machine. Electroplated bits, also known as wet/dry type, are only suitable for less hard materials. The diamonds are sharp and coarse and are only set on the surface. They have a much shorter service life than sintered bits and cannot be dressed (resharpened). Once they become dull, they must be replaced. They tend to work well with softer, abrasive materials like brick. Sintered bits, also known as wet type, are much longer lasting but require operator knowledge for best results. Water is absolutely always required with sintered bits. The bit is impregnated with many layers of diamond in its metal matrix. As the matrix (bond) wears, new diamonds are exposed. If the bit becomes glazed, it can be resharpened by dressing with an appropriate alumina oxide or silicon carbide dressing stick. There are many variables with sintered diamond core bits, such as diamond grade and type, diamond grit size, bond type, bond hardness, and bit wall thickness. Consult with your diamond core bit supplier for the best bit for your application. Work materials vary widely in hardness. 8 2) WATER SUPPLY Water is a basic requirement for diamond core drilling. The water serves as a coolant to avoid the working surface at the tip of the bit from overheating. When the diamond bit becomes overheated, both the bond matrix and even the diamonds break down. The most frequent cause of diamond core bit Closed damage is caused by drilling without enough coolant water. Water should always be used to cool and lubricate the bit and to flush out abrasive particles formed while drilling. Never use this machine without water feed. To connect the water supply. Attach the quick-release water coupling to a water hose. Open Water Feed Valve WARNING: Never allow water to enter the motor. It could lead to an electric shock. WARNING: Check all connections of the water feed system to ensure there are no leaks. Inspect hoses and other critical parts which could deteriorate. WARNING: The maximum water pressure should not exceed 70 psi (4 bar). CAUTION: There are two small holes on the top of the gearcase. If either of these holes leaks water, it indicates that the water seals are worn out. Replace them immediately. Indicator Holes CAUTION: Never use a wet-only machine without water feed. Running dry will overheat and destroy its water seals. Only convertible models may be used dry. Use a water collector with a wet vacuum to collect cooling water if nearby objects could be damaged by water. WARNING: Never allow water to enter the motor. A perfectly functioning water collector set up must be used for any drilling performed at an upward angle. Instructions for Inserting Adaptors for Convertible models: To attach either the water feed adaptor head or the vacuum adaptor, the universal port on the machine's gearbox is a bayonet connection. Align the slots on the adaptor with the tangs on the port. Insert fully and then twist clockwise to tighten. 3) SELECTING SPEEDS Gear Selector There are 3 speed ranges to suit the bit size and work piece hardness. Choose the slowest speed for large diameter bits and hard materials. If when cutting the bit stalls repeatedly, then you must change to a lower gear. If you are already in the lowest gear and the bit stalls repeatedly, then you are using the machine over its maximum capacity. 9 CAUTION: Never attempt to change gears on a running machine! Only adjust when the machine is at rest. Select the desired gear range by turning the gear selector either clockwise or counterclockwise into the desired gear. It will usually be necessary to turn the spindle by hand a little to get it to shift all the way. On constant speed models, it is necessary to first press the release button before shifting the gear. (Ensure that the release button pops back up, indicating that the gear is fully engaged.) Release Button Gear Selector Constant Speed Model 4) THE SWITCH Lock Button The machine has a lockable trigger switch. Squeeze the trigger to start the machine. To lock the switch on, press the lock button while holding the trigger switch on. To release, squeeze the trigger and release. Trigger Switch WARNING: Never lock the switch on when drilling hand-held. Only lock the switch on when mounted to a rig. 5) OVERLOAD PROTECTION, OVERHEAT PROTECTION Overload Warning System:(AVR equipped models only) When the load reaches overload conditions, the warning system will kick in, lowering the voltage and causing the motor to stop. Simply back off the downward pressure to ease the load and the motor will automatically restart. Then the operator can continue to drill normally. All models Indicator Light: The LED load indicator light will glow green when the load is within the normal range. When load is approaching overload, the indicator light will flash red. Overload: If the excessive load is sustained too long, the motor will shut down completely and the LED indicator light will glow solid red. In this case, the motor must be first shut off and then restarted. When this happens, the motor will very likely be near overheating, so it is also a good idea to run the motor at no load for a few minutes to cool it before continuing. Overheat Thermal Protection: Indicator Light Constant Speed Model Indicator Light Pistol-Handle Model Indicator Light D-Handle Model If the temperature of the motor gets too high, the thermal protection will shut the motor down and the LED 10 indicator light will glow solid red. The switch must be first shut off and then restarted. When this happens, do not immediately start drilling after restarting the motor. Always run the machine at no load for a few minutes to return to a normal operating temperature before continuing. CAUTION: The motor will be damaged if it is repeatedly overloaded or overheated. Always cool the motor by running at no load for a few minutes whenever it stops from either overheat or overload. 6) SAFETY CLUTCH This machine is equipped with a mechanical clutch to protect the operator and machine from excessive torque forces. When the preset maximum torque level is reached, the clutch will slip. After the clutch slips many times, it will become worn and slip at lower and lower torque levels. When this happens, it must be serviced by an authorized service provider. The recommended torque of the clutch nut is 21 Nm. 7) DIAMOND CORE DRILLING WARNING: When coring through a floor, the core will fall down. Take precautions to avoid injury or damage below. NOTE: When drilling with a new bit for the first time, use less than normal feed pressure for a time until it breaks-in. 1. Press the “Reset” button on the PRCD interrupter device to energize the circuit to the machine. Then squeeze the trigger switch to turn the machine on. WARNING: Hold the machine tightly with both hands to counteract the torque reaction force when the bit begins to turn. 2. 3. 4. Open the water valve slightly and very gently begin the cut. If holding by hand, start the cut by approaching at an angle of about 30 degrees to the cutting surface. (A large piece of wood with a large V notch cut in it will help prevent the bit from wandering at the beginning.) Once about a third of the arc is cut, straighten the bit to the correct perpendicular angle while keeping enough feed pressure on the bit to prevent it from wandering. (If using a rig, use very light feed pressure to prevent the bit from wandering until the bit is fully penetrated into the cut.) Make adjustments to the water feed as needed. The water leaving the cut should be a solid colored slurry with about the consistency of milk. If the exiting water is clear, then you may reduce the water flow. If the exiting water is thick and muddy, then increase the water. It’s very important that the water has enough pressure to flush cutting debris out of the cut. Once in the cut, use steady feed pressure for about 30 Wrong Right seconds, then back off feed pressure for a few seconds to allow 11 5. cutting debris to escape the kerf (cutting area) and for the cutting surface of the bit to cool. This has the added benefit of allowing the motor to remain within a good working temperature. Repeat this cycle until finished. When the cut is almost finished and the bit is about to break through, the bit will be very liable to get stuck. Take extra care gripping the machine tightly and reduce feed pressure at this point. WARNING: Whenever drilling by hand, always hold the drill in a position so that you can resist the considerable twisting forces created when the bit grabs. Never operate without the side handle tightly in place. WARNING: When the bit grabs, the machine will always twist in the counterclockwise direction. If you are drilling into the floor, make sure that the side handle is in front of your left leg, never between your legs. WARNING: Always keep your face away from the machine. Arrange the power supply cable with minimal slack and oriented in such a way that if the machine gets out of control and spins, it will immediately unplug its own cable. The diamond impregnated segments in a wet type (sintered) diamond core bit operate on a principle of controlled erosion. The bond matrix holding the diamonds is continually worn away by abrasion with the work piece, exposing the harder diamonds to stand proud from the bond matrix. A bit with good diamond exposure is a sharp bit. This erosion process causes heat and particles, which require water to cool and rinse free. Without adequate water, the bit would overheat and be destroyed. With too much water and not enough feed pressure, there would not be adequate erosion of the bond matrix (the diamonds not exposed) and the bit becomes dull (diamond segments polish smooth). This is called glazing and luckily the bit can be de-glazed (sharpened). If the bit seems to refuse to cut anymore, you know that it is glazed. See below: ”SHARPENING A GLAZED BIT ” Never use a sharp motion or the bit will be damaged. Conversely, don’t feed too gently or the diamond segments will become glazed. Keep the bit steadily working, but don’t be abusive or give the bit shock impacts into the work surface. If holding by hand, take great care to keep the bit aligned to the hole. If the bit is crooked, it will easily bind. If the cut is very deep, the core plug may be obstructing the flow of cooling water. In this case, stop drilling, and chisel out the core plug before continuing. CAUTION: If the bit gets stuck, do not try to rock it loose by turning the switch on and off. That is hazardous and could damage the motor. Rather, unplug the machine and use a wrench on the bit mounting to work it loose. If embedded steel such as rebar is encountered take special care. When the steel is encountered, the water will generally go clear and vibration will begin. Change to a lower gear if available. Reduce the feed pressure by about 1/3 and let the bit go at its own pace, if there is too much vibration the bit will be destroyed. Once the steel is passed, continue normally. A properly sharp bit with good diamond exposure should be able the cut through rebar if handled well. When the cut is finished keep the motor running until the bit is removed from the cut to avoid it getting stuck. 12 CAUTION: Drilling operations are very stressful to the motor and at the end of the cut, the motor temperature will be very hot, always run the motor at no load for a few minutes until the temperature returns to a normal range before shutting off. Turn the water feed down to a very small amount of flow (not off), just enough to keep the water seals from overheating when you perform this step. Then turn off the switch and allow the coasting bit to stop before setting it down. RESHARPENING A GLAZED BIT If the bit becomes glazed, the ideal way to resharpen and true it up is by dressing with an appropriate alumina oxide or silicon carbide dressing stone. Simply drill into the stick as many times as necessary to restore its cutting performance. If it is only slightly dull, while cutting, you may first reduce the water flow by about half until the water exiting the kerf is really muddy. Another method is to stop and add about 6mm (1/4”) of coarse silica sand in the kerf and and drill for a few minutes, then turn up the water to rinse the sand free. Repeat as needed. Another method is to drill into a cinder block. Repeat as needed. If that still does not work the only choice is to use a dressing stone. VIBRATION TROUBLESHOOTING If vibration occurs and it is not caused by embedded steel, stop drilling to find the cause and remedy. CAUTION: Do not operate with vibration or there will be serious hazard and the diamond core bit will surely be destroyed. Vibration is usually caused by: 1. A bit with too much runout SOLUTION: Replace bit. 2. A bit with diamond segments broken off SOLUTION: Repair or Replace bit. KEEP TOOL CLEAN Wipe down the machine at the end of each work day with a damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Periodically blow low-pressure compressed air through the ventilation slots with the motor running to keep the motor clean so that motor can be cooled normally. Wear safety glasses while using compressed air. CAUTION: When drilling in a position with the motor near to the floor, take measures to prevent dust, debris and slurry from being sucked into the motor's cooling slots MAINTENANCE Every 50 hours of operation blow compressed air through the motor while running at no load to clean out 13 accumulated dust. (If operating in especially dusty conditions, perform this operation more often.) To keep your diamond coring machine in top condition, periodic maintenance must be performed. In addition always check for a damaged power supply cable, check for loose fasteners and always keep alert for unusual noises and vibration when operating. WARNING: Never operate a damaged machine. Always tag a damaged machine and take it out of service until repairs can be made. CAUTION: This machine is equipped with an oil bath gearbox. To avoid leakage of lubricating oil, whenever the gearbox is opened, the o-ring seal must be replaced with a new one. Maintenance which should be performed by an authorized service center, include the following: • Replace water seals as needed. • Replace the carbon brushes as needed • Change the gear oil about every 100 hours of operation • Replace the clutch discs and spring as needed. Each year perform a full mechanical inspection, cleaning and re-lubrication. THE CARBON BRUSHES The carbon brushes are a normal wearing part and must be replaced when they reach their wear limit. This machine is equipped with auto-stop carbon brushes. If the machine comes to a stop unexpectedly, the brushes should be checked. The auto-stop brush design protects the motor by stopping the machine before the carbon brushes are completely worn out. Caution: Always replace the brushes as a pair. To replace: 1. 2. 3. 4. 5. Remove the 4 screws and remove the motor tail cover. For D-handle models, the D-handle must first be removed. Remove the 13 screws to remove the D-handle and tail cover. Carefully move the parts to one side, taking care not to strain the wiring. Using pliers rotate the brush spring out of the way and slide the old carbon brush out of the brush holder. Unscrew the screw to remove the brush lead. The old carbon brush may now be lifted away. Install a new brush. Installation is the reverse of removal. Replace the motor tail cover. For D-handle models, replacement of the D-handle is the reverse of removal. Take care not to pinch any wires when reassembling. If the replacement of the power supply cord is necessary, this has to be done by the manufacturer or their agent in order to avoid a safety hazard. WARNING: All repairs must be entrusted to an authorized service center. Incorrectly performed repairs could lead to injury or death. Do not throw electric power tools into the household waste! In accordance with the European Directive 2002/96/EG on Waste Electrical and Electronic Equipment and transposition into national law, used electric power tools must be collected separately and recycled in an environmentally friendly manner. 14 BLACK BLACK BRUSH STATOR BLACK (TEMP. SENSOR) BLACK BLACK AC WHITE LED WHITE SWITCH 1 1 BRUSH 2 15 2 ELECTRONICS UNIT WIRING 16 96 17 NO.01~102 Version 3.3 14 06 19 89 07 21 18 22 14 05 15 04 94 90 91 13 93 09 29 28 25 11 03 26 08 02 15 39 40 01 66 27 42 12 67 44 37 70 98 OPTIONAL 69 30 45 95 38 101 46 48 49 71 31 39 50 51 102 85 100 64 52 53 32 54 86 56 74 75 99 33 76 84C 63 84A 77 55 78 34 59 60 77 36 35 79 81 80 65 82 83 D-Handle Model Exploded View D-Handle Model Parts List NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Parts Name POWER SUPPLY CABLE PRCD INTERRUPTER PROTECTION 110V.220V CORD ARMOR CABLE CLIP PANHEAD TAPPING SCREW M4x14 BULLS-EYE LEVEL SWITCH 110V / 220V SPIRIT LEVEL 10x10x29 LED OVERLOAD LAMP 110V / 220V N/A D-HANDLE HALF-RIGHT D-HANDLE HALF-LEFT PANHEAD TAPPING SCREW M4x16 SOCKET CAP SCREW M5x40 SOCKET CAP SCREW M5x16 N/A MOTOR END CASTING INSULATING COVER PANHEAD TAPPING SCREW M4x12 N/A BRUSH SPRING 0.4x4x3T CARBON BRUSH 7x17x19 110V/220V N/A N/A NYLOCK NUT M5 INSULATING SLEEVE MOTOR HOUSING ELECTRONICS UNIT 110V/ 220V PANHEAD MACHINE SCREW M4x10 MOTOR INSULATION SLEEVE STATOR 110V/220V -81x45.8x70 PANHEAD MACHINE SCREW M5x95 BALL BEARING 6200 ARMATURE 110V/220V -81x45.8x70 BALL BEARING 6201 OIL SEAL Ø12 x Ø22 x 7 GEAR PLATE O-RING Ø92 x 2 BALL BEARING 608 CLUTCH NUT M10 N/A PRESSURE DISC Ø12.1xØ28x2.65 N/A INPUT GEAR M1.0x38T BUSHING Ø12xØ18x5 INPUT SHAFT M1.25x24Tx12Tx8T N/A NEEDLE BEARING HK 1010 INTERNAL CIRCLIP IS14 OUTPUT GEAR M1.25 x 29T SPINDLE GEAR M1.25x42T INTERNAL CIRCLIP IS18 Q'TY 1 1 1 1 2 1 1 1 1 1 1 6 4 4 1 1 2 2 2 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 NO. 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84A 84B 84C 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 17 Parts Name OUTPUT GEAR M1.25 x 46T OIL SEAL Ø22 x Ø32 x 7 GEAR HOUSING SOCKET CAP SCREW M5x12 N/A N/A O-RING Ø20 x 3 GEAR SELECTOR N/A N/A WATER FEED CONNECTOR KIT WATER COUPLING 1/2" SOCKET CAP SCREW M5x50 OIL SEAL Ø25 x Ø45 x 7 OIL SEAL Ø25 x Ø47 x 7 N/A EXTERNAL CIRCLIP S-25 BALL BEARING 6205 PARALLEL KEY 5x5x40 N/A N/A INTERNAL CIRCLIP R-52 DOWEL PIN Ø4 x 11.8 ANTI-SEIZE CUP O-RING Ø32 x 1.5 THRUST RING 3252-B ANTI-SEIZE RING O-RING Ø49 x 1.5 HANDLE CLAMP SPACER Ø6.1xØ12x10 THUMB SCREW M6x55 FRONT HANDLE M12xP1.75 N/A FRONT HANDLE M12 COMBINATION WRENCH M32 FAN BAFFLE Ø48xØ87.5x1 N/A N/A O-RING Ø30 x 1.5 PANHEAD MACHINE SCREW M4x8 BRUSH HOLDER PLATE ASSY. N/A EXTERNAL STAR WASHER M4 PANHEAD MACHINE SCREW M4x6 CLUTCH DISC SET GASKET N/A PILOT DRILL SOCKET SELECTOR DISC SPINDLE SET 1-1/4"-7 x 1/2"BSP STAINLESS BUSHING Ø23xØ25x9 FLAG TERMINAL Q'TY 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 1 16 06 09 01 02 14 15 19 03 17 97 89 21 22 18 11 05 04 18 95 91 92 94 90 29 28 15 25 26 93 07 13 40 66 27 42 67 44 NO.01~103 Version 3.1 12 39 37 69 30 45 102 99 46 48 OPTIONAL 70 96 38 49 71 39 50 51 31 85 64 52 53 101 32 103 54 86 56 74 75 100 33 63 84A 76 84C 77 55 78 34 59 60 77 36 35 79 81 80 65 82 83 Pistol-Handle Model Exploded View Pistol-Handle Model Parts List NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23~24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 Parts Name POWER SUPPLY CABLE PRCD INTERRUPTER PROTECTION 110V/220V CORD ARMOR CABLE CLIP PANHEAD TAPPING SCREW M4x14 BULLS-EYE LEVEL SWITCH 110V&220V N/A LED OVERLOAD LAMP 110V & 220V N/A HANDLE HALF-RIGHT HANDLE HALF-LEFT PANHEAD TAPPING SCREW M4x16 SOCKET CAP SCREW M5x30 SOCKET CAP SCREW M5x20 BUTT PLATE MOTOR END CASTING INSULATING COVER PANHEAD TAPPING SCREW M4x12 N/A BRUSH SPRING 0.4x4x3T CARBON BRUSH 7x17x19 110V / 220V N/A NYLOCK NUT M5 INSULATING SLEEVE MOTOR HOUSING ELECTRONICS UNIT 110V / 220V PANHEAD MACHINE SCREW M4x10 MOTOR INSULATION SLEEVE STATOR 110V/ 220V -81x45.8x70 PANHEAD MACHINE SCREW M5x95 BALL BEARING 6200 ARMATURE 110V / 220V -81x45.8x70 BALL BEARING 6201 OIL SEAL Ø12 x Ø22 x 7 GEAR PLATE O-RING Ø92 x 2 BALL BEARING 608 CLUTCH NUT M10 N/A PRESSURE DISC Ø12.1xØ28x2.65 N/A INPUT GEAR M1.0x38T BUSHING Ø12xØ18x5 INPUT SHAFT M1.25x24Tx12Tx8T N/A NEEDLE BEARING HK 1010 INTERNAL CIRCLIP IS14 OUTPUT GEAR M1.25 x 29T SPINDLE GEAR M1.25x42T Q'TY 1 1 1 1 2 1 1 1 1 1 4 4 4 1 1 1 2 2 2 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 NO. 52 53 54 55 56 57~58 59 60 61~62 63 64 65 66 67 68 69 70 71 72~73 74 75 76 77 78 79 80 81 82 83 84A 84B 84C 85 86 87~88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 19 Parts Name INTERNAL CIRCLIP IS18 OUTPUT GEAR M1.25 x 46T OIL SEAL Ø22 x Ø32 x 7 GEAR HOUSING SOCKET CAP SCREW M5x12 N/A O-RING Ø20 x 3 GEAR SELECTOR N/A WATER FEED CONNECTOR KIT WATER COUPLING SOCKET CAP SCREW M5x50 ~ OIL SEAL Ø25 x Ø45 x 7 OIL SEAL Ø25 x Ø47 x 7 N/A EXTERNAL CIRCLIP S-25 BALL BEARING 6205 PARALLEL KEY 5x5x40 N/A INTERNAL CIRCLIP R-52 DOWEL PIN Ø4 x 11.8 ANTI-SEIZE CUP O-RING Ø32 x 1.5 THRUST RING 3252-B ANTI-SEIZE RING O-RING Ø49 x 1.5 HANDLE CLAMP SPACER Ø6.1xØ12x10 THUMB SCREW M6x55 FRONT HANDLE M12 N/A FRONT HANDLE M12 WRENCH M32 FAN BAFFLE Ø48xØ87.5x1 N/A O-RING Ø30 x 1.5 PANHEAD TAPPING SCREW M4x8 PANHEAD MACHINE SCREW M4x8 BRUSH HOLDER PLATE ASSY. SPIRIT LEVEL 1 0x10x29 EXTERNAL STAR WASHER M4 PANHEAD MACHINE SCREW M4x6 CLUTCH DISC SET GASKET N/A PILOT DRILL SOCKET SELECTOR DISC SPINDLE SET 1-1/4"-7 x 1/2"BSP STAINLESS BUSHING Ø23xØ25x9 FLAG TERMINAL Q'TY 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 1 81 17 83 80 79 20 78 84 66 88 77 77 76 75 31 57 30 A2 65 74 OPTIONAL 56 73 55 85 54 29 53 52 64 63 72 62 86 51 71 61 50 70 28 69 60 48 59 67 A1 27 47 58 26 45 09 25 46 NO.01~92 A1~A2 Version 2.3 49 68 68 44 24 43 23 41 92 42 40 22 03 05 07 20 39 08 19 90 04 38 19 10 21 06 18 35 03 02 36 32 03 37 33 17 34 01 15 87 16 13 15 12 14 11 Constant Speed Model Exploded View Constant Speed Model Parts List NO. Parts Name Q'TY NO. Parts Name 1 POWER SUPPLY CABLE 1 48 INPUT GEAR M1.0x45T 1 2 CORD ARMOR 1 49 INPUT SHAFT M1.25x29TxM1.25x18TxM1.25x10T 1 3 PANHEAD TAPPING SCREW M4x16 8 50 BALL BEARING 6200 1 4 SOCKET CAP SCREW M5x20 4 51 GASKET 1 5 SWITCH 110V&220V 1 52 SELECTOR DISC 1 6 PANHEAD TAPPING SCREW M4x10 1 53 SOCKET CAP SCREW M5x16 1 7 CABLE CLIP 1 54 GEAR SELECTOR 1 8 PANHEAD TAPPING SCREW M4x14 2 55 SPRING Ø0.6xØ3.8xØ5x11Tx35L 1 Q'TY 9 HANDLE HALF-RIGHT 1 56 RELEASE PIN 1 10 HANDLE HALF-LEFT 1 57 O-RING Ø20x3 1 11 BULLS-EYE LEVEL 1 58 NEEDLE BEARING HK 1010 1 12 SOCKET CAP SCREW M4x16 2 59 INTERNAL CIRCLIP IS14 1 13 LED INDICATOR LIGHT 1 60 OUTPUT GEAR M1.25x39T 1 14 BUTT PLATE 1 61 SPINDLE GEAR M1.25x50T 1 15 PANHEAD TAPPING SCREW M4x30 2 62 INTERNAL CIRCLIP IS18 1 16 ELECTRONICS UNIT 110V/220V 1 63 OUTPUT GEAR M1.25x58T 1 17 SOCKET CAP SCREW M5x60 8 64 OIL SEAL Ø22xØ32x7 1 18 MOTOR END CASTING 1 65 GEAR HOUSING 1 19 PANHEAD MACHINE SCREW M4x6 2 66 SPRING WASHER M5 4 20 BRUSH SPRING 0.4x4x3T 2 67 OIL SEAL Ø27xØ42x7 1 21 CARBON BRUSH 7x17x20 2 68 STAINLESS BUSHING 2 22 PANHEAD TAPPING SCREW M4x8 4 69 OIL SEAL Ø27xØ45x8 1 23 CARBON BRUSH HOLDER 7x17 2 70 EXTERNAL CIRCLIP S-28 1 24 BRUSH HOLDER PLATE 1 71 BALL BEARING 60/28 1 25 MOTOR HOUSING 1 72 PARALLEL KEY 5x5x40 1 26 NYLOCK NUT M5 2 73 SPINDLE SET 1 1/4"-7 x 1/2"BSP-222.7MM 1 27 INSULATING SLEEVE 2 74 INTERNAL CIRCLIP R-52 1 28 MOTOR INSULATION SLEEVE 1 75 DOWEL PIN Ø4x11.8 2 29 STATOR 110V/220V-94x54x55 1 76 ANTI-SEIZE CUP 1 30 PANHEAD MACHINE SCREW M5x80 2 77 O-RING Ø32x1.5 2 31 FAN BAFFLE 1 78 THRUST RING 3252 1 32 PANHEAD TAPPING SCREW M4x10 1 79 ANTI-SEIZE RING 1 33 FLAT WASHER Ø4xØ10x1 1 80 O-RING Ø49x1.5 1 34 RUBBER WASHER Ø4xØ11x1 1 81 HANDLE CLAMP 1 35 PICKUP MAGNET Ø8xØ15x5 1 82 SPACER Ø6.1xØ12x10 1 36 SPACER Ø8xØ12x10.5 1 83 THUMB SCREW M6x55 1 37 BALL BEARING 6200 1 84 FRONT HANDLE M12 1 38 ARMATURE 220V-94x54x55 1 85 WATER FEED CONNECTOR KIT 1 39 BALL BEARING 6201 1 86 WATER COUPLING 1/2' 1 40 OIL SEAL Ø12xØ22x7 1 87 PRCD INTERRUPTER PROTECTION 220V 1 1 41 GEAR PLATE 1 88 HEX BOLT M6x60 42 ROLL PIN Ø5x12 2 89 N/A - 43 NEEDLE BEARING HK 0810 1 90 EXTERNAL STAR WASHER (M4) 1 44 CLUTCH NUT M12xP1.75x9T 1 91 N/A - 45 CLUTCH DISC SET 1 92 WRENCH M32 1 46 PRESSURE DISC Ø34.8xØ16x2.5 1 A1 FRONT HANDLE M12 1 47 BUSHING Ø15.9xØ22x4.7 1 A2 PILOT DRILL SOCKET 1 21 14 100 06 17 19 89 07 21 18 22 14 22 90 92 05 15 04 94 13 93 09 29 28 25 11 03 26 08 02 15 39 40 01 27 66 42 12 67 44 37 70 103 113 46 48 49 31 71 39 50 114 51 NO.01~114 Version 3.4 OPTIONAL 69 30 45 101 38 52 32 85 112 53 54 86 56 74 104 84C 75 33 84A 76 34 78 59 55B 77 55A 60 77 83 79 36 35 80 65 82 81 99 98 97 96 95 FOR NO.55A 111 110 108 109 108 108 107 106 105 FOR NO.55B Convertible Models: D-Handle Model Exploded View Convertible Models: D-Handle Model Parts List NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23~24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55A 55B Parts Name POWER SUPPLY CABLE PRCD INTERRUPTER PROTECTION 110V / 220V CORD ARMOR CABLE CLIP PANHEAD TAPPING SCREW M4x14 BULLS-EYE LEVEL SWITCH 110V&220V SPIRIT LEVEL 10x10x29 LED OVERLOAD LAMP 110V&220V N/A D-HANDLE HALF-RIGHT D-HANDLE HALF-LEFT PANHEAD TAPPING SCREW M4x16 SOCKET CAP SCREW M5x40 SOCKET CAP SCREW M5x16 N/A MOTOR END CASTING INSULATING COVER PANHEAD TAPPING SCREW M4x12 N/A BRUSH SPRING 0.4x4x3T CARBON BRUSH 7x17x19/110V , 7x17x20/220V N/A NYLOCK NUT M5 INSULATING SLEEVE MOTOR HOUSING ELECTRONICS UNIT 110V / 220V PANHEAD MACHINE SCREW M4x10 MOTOR INSULATION SLEEVE STATOR 110V 220V-81x45.8x70 PANHEAD MACHINE SCREW M5x95 BALL BEARING 6200 ARMATURE 110V 220V -81x45.8x70 BALL BEARING 6201 OIL SEAL Ø12 x Ø22 x 7 GEAR PLATE O-RING Ø92 x 2 BALL BEARING 608 CLUTCH NUT M10 N/A PRESSURE DISC Ø12.1xØ28x2.65 N/A INPUT GEAR M1.0x38T BUSHING Ø12xØ18x5 INPUT SHAFT M1.25x24Tx12Tx8T N/A NEEDLE BEARING HK 1010 INTERNAL CIRCLIP IS14 OUTPUT GEAR M1.25 x 29T SPINDLE GEAR M1.25x42T INTERNAL CIRCLIP IS18 OUTPUT GEAR M1.25 x 46T OIL SEAL Ø22 x Ø32 x 7 GEAR HOUSING GEAR HOUSING Q'TY 1 1 1 1 2 1 1 1 1 1 1 6 4 4 1 1 2 2 2 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 NO. 56 57~58 59 60 61~64 65 66 67 68 69 70 71 72~73 74 75 76 77 78 79 80 81 82 83 84A 84B 84C 85 86 87~88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 23 Parts Name SOCKET CAP SCREW M5x12 N/A O-RING Ø20 x 3 GEAR SELECTOR N/A SOCKET CAP SCREW M5x50 OIL SEAL Ø25 x Ø45 x 7 OIL SEAL Ø25 x Ø47 x 7 N/A EXTERNAL CIRCLIP S-25 BALL BEARING 6205 PARALLEL KEY 5x5x40 N/A INTERNAL CIRCLIP R-52 DOWEL PIN Ø4 x 11.8 ANTI-SEIZE CUP O-RING Ø32 x 1.5 THRUST RING ANTI-SEIZE RING O-RING Ø49 x 1.5 HANDLE CLAMP SPACER Ø6.1xØ12x10 THUMB SCREW M6x55 FRONT HANDLE M12xP1.75 N/A FRONT HANDLE M12 COMBINATION WRENCH M32 FAN BAFFLE Ø48xØ87.5x1 N/A O-RING Ø30 x 1.5 PANHEAD MACHINE SCREW M4x8 N/A BRUSH HOLDER PLATE ASSY. EXTERNAL STAR WASHER M4 PANHEAD MACHINE SCREW M4x6 O-RING Ø22 x Ø25 x 1.5 UNIVERSAL PORT PANHEAD MACHINE SCREW M4x16 VACUUM ADAPTOR WATER FEED CONNECTOR KIT 1/2" GASKET CLUTCH DISC SET N/A PILOT DRILL SOCKET SELECTOR DISC NIPPLE 3/4"PS-14 SEAL Ø19xØ26x3 GEKA FEMALE CLAW 3/4"BSP SEAL GEKA HOSE CLAW 1-1/2" GEKA MALE CLAW 1/4"BSP WATER FEED CONNECTOR KIT SPINDLE SET 1-1/4"-7 x 1/2"BSP STAINLESS BUSHING Ø23xØ25x9 FLAG TERMINAL Q'TY 1 1 1 4 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 4 1 1 1 1 1 1 1 1 1 3 1 1 1 1 2 1 16 06 09 01 02 14 15 19 03 17 100 89 21 24 11 05 04 18 22 94 91 92 93 29 28 15 90 25 26 08 07 13 40 27 66 42 67 44 68 69 101 70 38 103 OPTIONAL 30 45 NO.01~113 Version 3.2 12 39 37 113 46 48 49 71 39 50 51 31 52 32 85 112 53 54 86 56 74 104 84C 75 33 84A 76 34 78 59 55B 77 55A 60 77 83 79 36 35 80 65 82 81 99 98 97 95 96 FOR NO.55A 111 110 108 109 108 108 107 106 105 FOR NO.55B Convertible Models: Pistol-Handle Model Exploded View Convertible Models: Pistol-Handle Model Parts List NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23~24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55A 55B Parts Name POWER SUPPLY CABLE PRCD INTERRUPTER PROTECTION 110V/220V CORD ARMOR CABLE CLIP PANHEAD TAPPING SCREW M4x14 BULLS-EYE LEVEL SWITCH 110V&220V SPIRIT LEVEL 10x10x29 LED OVERLOAD LAMP 110V & 220V N/A HANDLE HALF-RIGHT HANDLE HALF-LEFT PANHEAD TAPPING SCREW M4x16 SOCKET CAP SCREW M5x30 SOCKET CAP SCREW M5x20 BUTT PLATE MOTOR END CASTING INSULATING COVER PANHEAD TAPPING SCREW M4x12 N/A BRUSH SPRING 0.4x4x3T CARBON BRUSH 7x17x19/110V , 7x17x20/220V N/A NYLOCK NUT M5 INSULATING SLEEVE MOTOR HOUSING ELECTRONICS UNIT 110V / 220V PANHEAD MACHINE SCREW M4x10 MOTOR INSULATION SLEEVE STATOR 110V / 220V-81x45.8x70 PANHEAD MACHINE SCREW M5x95 BALL BEARING 6200 ARMATURE 110V 220V -81x45.8x70 BALL BEARING 6201 OIL SEAL Ø12 x Ø22 x 7 GEAR PLATE O-RING Ø92 x 2 BALL BEARING 608 CLUTCH NUT M10 N/A PRESSURE DISC Ø12.1xØ28x2.65 N/A INPUT GEAR M1.0x38T BUSHING Ø12xØ18x5 INPUT SHAFT M1.25x24Tx12Tx8T N/A NEEDLE BEARING HK 1010 INTERNAL CIRCLIP IS14 OUTPUT GEAR M1.25 x 29T SPINDLE GEAR M1.25x42T INTERNAL CIRCLIP IS18 OUTPUT GEAR M1.25 x 46T OIL SEAL Ø22 x Ø32 x 7 GEAR HOUSING GEAR HOUSING Q'TY 1 1 1 1 2 1 1 1 1 1 1 4 4 4 1 1 1 2 2 2 2 2 1 1 2 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 NO. 56 57~58 59 60 61~64 65 66 67 68 69 70 71 72~73 74 75 76 77 78 79 80 81 82 83 84A 84B 84C 85 86 87~88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 25 Parts Name SOCKET CAP SCREW M5x12 N/A O-RING Ø20 x 3 GEAR SELECTOR N/A SOCKET CAP SCREW M5x50 OIL SEAL Ø25 x Ø45 x 7 OIL SEAL Ø25 x Ø47 x 7 N/A EXTERNAL CIRCLIP S-25 BALL BEARING 6205 PARALLEL KEY 5x5x40 N/A INTERNAL CIRCLIP R-52 DOWEL PIN Ø4 x 11.8 ANTI-SEIZE CUP O-RING Ø32 x 1.5 THRUST RING 3252-B ANTI-SEIZE RING O-RING Ø49 x 1.5 HANDLE CLAMP SPACER Ø6.1xØ12x10 THUMB SCREW M6x55 FRONT HANDLE (M12xP1.75)M12 N/A FRONT HANDLE M12 WRENCH (M32) FAN BAFFLE Ø48xØ87.5x1 N/A O-RING Ø30 x 1.5 PANHEAD TAPPING SCREW-B M4x8 PANHEAD MACHINE SCREW M4x8 BRUSH HOLDER PLATE ASSY. EXTERNAL STAR WASHER M4 PANHEAD MACHINE SCREW M4x6 O-RING Ø22 x Ø25 x 1.5 UNIVERSAL PORT PANHEAD MACHINE SCREW M4x16 VACUUM ADAPTOR WATER FEED CONNECTOR KIT 1/2" GASKET CLUTCH DISC SET N/A PILOT DRILL SOCKET SELECTOR DISC NIPPLE 3/4"PS-14 SEAL Ø19xØ26x3 GEKA FEMALE CLAW 3/4"BSP SEAL GEKA HOSE CLAW 1-1/2" GEKA MALE CLAW 1/4"BSP WATER FEED CONNECTOR KIT SPINDLE SET 1-1/4"-7 x 1/2"BSP STAINLESS BUSHING Ø23xØ25x9 Q'TY 1 1 1 4 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 4 1 1 1 1 1 1 1 1 1 3 1 1 1 1 2 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Multiple speed mechanical gearbox
- Mechanical safety clutch
- Overload and thermal protection
- Water feed system for cooling
- Built-in spirit levels for alignment
- PRCD interrupter for electrical safety
- Convertible models offer water and dust options
Frequently asked questions
Remove the machine from the workpiece and run at no load for at least 3 minutes to allow the motor to cool before returning to operation.
The water serves as a coolant to avoid the working surface at the tip of the bit from overheating, to lubricate the bit, and to flush out abrasive particles.
Wet-type (sintered) bits are recommended for these machines. Electroplated bits can be used for less hard materials but with shorter service life.
It provides protection against electric shock hazards and must be used at all times.