Allstar 8833 OCS 831, 8833C OCS 733, 639, 535 Commercial Transmitter User Manual

READ THIS MANUAL CAREFULLY
BEFORE BEGINNING
COMMERCIAL
TRANSMITTER
INSTRUCTIONS
MODELS:
• 831, 8833 OCS:
• 733, 8833C OCS:
• 639:
• 535:
1-DOOR
3-DOOR
9-DOOR
27-DOOR
PRODUCT FEATURES
Allstar Commercial Transmitters are designed to work with Allstar Receivers. Some models are designed to operate multiple
receivers. A selector switch on the Transmitter determines which door will be controlled in a multi-door installation. The Receiver is
connected to the commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio
control.
IMPORTANT INSTALLATION NOTES
WARNING
•
•
•
•
•
•
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS!
ALLSTAR TRANSMITTERS ARE INTENDED FOR
USE WITH COMMERCIAL DOOR OPERATORS ONLY.
DO NOT USE FOR ANY OTHER PURPOSE. DO NOT
MODIFY IN ANY MANNER.
CHECK LOCAL BUILDING AND ELECTRICAL
CODES FOR MANDATORY INSTALLATION AND
WIRING REQUIREMENTS.
CONNECT POWER CORDS ONLY TO A PROPERLY
GROUNDED OUTLET. IF PERMANENT WIRING IS
REQUIRED BY CODES, DISCONNECT POWER AT
FUSE BOX OR CIRCUIT BREAKER BEFORE
ATTEMPTING ANY WIRING CONNECTIONS.
DO NOT WEAR RINGS, WATCHES OR LOOSE
CLOTHING WHILE INSTALLING OR SERVICING
GARAGE DOOR OPENERS.
WEAR SAFETY
GOGGLES OR OTHER PROTECTIVE EYEWEAR.
AN UNBALANCED DOOR OR ONE THAT STICKS OR
BINDS MAY CAUSE INJURY OR DEATH. ENSURE
DOOR IS PROPERLY BALANCED AND ELIMINATE
ANY STICKING OR BINDING.
YOUR GARAGE DOOR IS A LARGE MOVING
OBJECT. THE SPRINGS, PULLEYS, CABLES AND
MOUNTING HARDWARE UTILIZED TO BALANCE
•
•
•
ITS OPERATION ARE UNDER EXTREME TENSION
AT ALL TIMES AND CAN CAUSE SERIOUS
PERSONAL INJURY, EVEN DEATH, IF DISTURBED.
ONLY A QUALIFIED SERVICE PERSON SHOULD
MOVE, LOOSEN OR ADJUST DOOR SPRINGS OR
HARDWARE.
LOCATE CONTROL PUSHBUTTONS WITHIN
SIGHT OF THE DOOR AND AWAY FROM THE
MOVING PARTS OF THE DOOR.
INSTALL
ENTRAPMENT WARNING LABEL NEXT TO THE
CONTROL PUSHBUTTON IN A PROMINENT
LOCATION.
REMOVE ALL ROPES AND REMOVE OR MAKE
INOPERATIVE ALL LOCKS CONNECTED TO THE
GARAGE DOOR.
THE
IMPORTANT
SAFEGUARDS
AND
INSTRUCTIONS IN THIS MANUAL CANNOT
COVER ALL POSSIBLE CONDITIONS AND
SITUATIONS. IT MUST BE UNDERSTOOD THAT
COMMON SENSE AND CAUTION MUST BE
EXERCISED BY THE PERSON(S) INSTALLING,
MAINTAINING
AND
OPERATING
THIS
EQUIPMENT.
INSTALLER: Leave this manual with your customer upon completion of the installation.
Page 1 of 4
P/N 107343 Rev D
COMMERCIAL TRANSMITTER MODELS
WARNING
IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY.
FOLLOW LOCAL BUILDING AND ELECTRICAL CODES.
WARNING
TO PREVENT ELECTROCUTION DISCONNECT POWER AT FUSE BOX AND DOOR OPENER
BEFORE WIRING PERMANENTLY.
The various Transmitter models are shown below. All models may be coded to work with Allstar 3-channel Receivers such as the
831R, 831RE and the 8833R. Refer to the individual instructions for proper wiring of the Receivers.
Follow the directions on the next page for proper Transmitter/Receiver Coding!
CLOSE
OPEN
OPEN
STOP
CLOSE
STOP
8833-OCS
831
Slide Switch
selects door
A, B or C
Rotary Switch
selects door
A, B or C
8833C-OCS
733
Combination of
both Rotary
Switches selects
door
Examples: A1, B7,
C9, etc.
Rotary Switch
selects door
1, 2, 3, ... or 9
535
639
WARNING
DO NOT USE RADIO CONTROLS ON COMMERCIAL DOOR OPERATORS UNLESS PROPER
ENTRAPMENT PROTECTION DEVICES ARE INSTALLED. CONSULT THE MANUFACTURER OF
YOUR OPERATOR FOR MORE DETAILS.
Page 2 of 4
P/N 107343 Rev D
COMMERCIAL RECEIVER &
TRANSMITTER CODING INSTRUCTIONS
The information below indicates how to set the coding switches in the various transmitters and receivers.
IF
YOU ARE USING A 8833 OCS-ECONOMY OR
831 STANDARD TRANSMITTER:
Exactly match all 8 code switches in the transmitter and receiver. The code switches
may be set in any random pattern of +, - and 0.
IF
YOU ARE USING A
8833C
OCS-ECONOMY OR
733
STANDARD
TRANSMITTER
A-B-C Selector
Switch Position
A
RECEIVER
Coding Switch
#6
+
TRANSMITTER:
B
0
This transmitter is used to control up to 3 different doors. This is accomplished by
setting the selector switch on the transmitter to either A, B & C and setting the #6
coding switch in the 831 receiver .
C
-
Start coding by exactly matching all 8 code switches in the transmitter and the receivers. The code switches may be set in any random
pattern of +, 0 and - positions. Next, in receiver A, set code switch #6 to the + position; In receiver B set code switch # 6 to the 0
position; In receiver C set code switch # 6 to the - position. The table to the right shows the switch positions.
IF
YOU ARE USING A
639 STANDARD TRANSMITTER:
This transmitter is used to control up to 9 different doors. This is
accomplished by setting the selector switch on the transmitter to
either 1, 2, 3, 4, 5, 6, 7, 8 or 9 and setting the #7 and #8 coding
switches in the 831 receiver.
TRANSMITTER
1 - 9 Selector
Switch Position
1
Start coding by exactly matching all 8 code switches in the
transmitter and receivers. The code switches may be set in any
random pattern of +, 0 and - positions. Next, in receiver 1, set
code switch #7 to + and code switch #8 +; In receiver 2, set code
switch #7 to + and code switch #8 to 0. Continue setting the
codes in the 831E receivers as shown in the table.
IF
YOU ARE USING A
535 STANDARD TRANSMITTER:
This transmitter is used to control up to 27 different doors. This
is accomplished by setting the selector switches to either A, B or
C and either 1, 2, 3, 4, 5, 6, 7, 8 or 9 and setting the #6, #7 and
#8 coding switches in the 831 receiver.
831 RECEIVER 831 RECEIVER
Code Switch #7 Code Switch #8
+
+
2
+
0
3
+
-
4
0
+
5
0
0
6
0
-
7
-
+
8
-
0
9
-
-
Start coding by exactly matching all 8 code switches in the transmitter and receiver. Next, in receiver A1, set code switch #6 to +, set
code switch #7 to + and code switch #8 to +; In receiver A2, set code switch #6 to +, set code switch #7 to + and code switch #8 to
0. Continue setting the codes in the 831 receivers, using both tables shown above.
WARNING
DISCONNECT POWER AT FUSE BOX AND DOOR OPENER BEFORE WIRING
PERMANENTLY TO PREVENT ELECTROCUTION.
Page 3 of 4
P/N 107343 Rev D