Metra 99-7422 radio installation kit Installation instructions

INSTALLATION INSTRUCTIONS FOR PART 99-7422
APPLICATIONS
See application list inside
Nissan Sentra 2007-2012 (without pocket door)
99-7422
KIT FEATURES
• DIN radio provision with pocket
• Double DIN radio provision
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness:
• 70-7552 - Nissan harness 2007-up
• NIRD-01 - Nissan display and Bluetooth retention
harness 2007-2008
Antenna Adapter:
• 40-NI12 - Nissan harness 2007-up
TOOLS REQUIRED
• Small flat blade screwdriver • Panel removal tool
• Phillips screwdriver • Hook tool • Socket set
REV. 1/27/2014 INST99-8231
KIT COMPONENTS
• A) Radio housing • B) Radio housing trim plate • C) Double DIN trim plate • D) Radio housing brackets
• E) Carriage bolts • F) (2) Nuts
A
B
C
D
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
E
METRA. The World’s best kits.™
F
NOTE: Refer to the instructions included with the
aftermarket radio.
1-800-221-0932
metraonline.com
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
99-7422
Dash Disassembly 99-7422
Table of Contents
Nissan Sentra 2007-2012 (without pocket door)
Dash Disassembly
– Nissan Sentra 2007-2012 (without pocket door) ............................ 2-3
Kit Assembly
– Kit preparation ............................................................................... x
– DIN radio provision with pocket ...................................................... x
– Double DIN radio provision ............................................................. x
1. Push down on the collar below the shift knob to
unclip. Using a small screwdriver or hook tool
remove the spring clip to release and remove
the shift knob. (Figure A)
LO
c
HI
2. Unclip and remove shifter trim panel around
shifter. (Figure B)
3. Unclip and remove the A/C control panel.
(Figure C)
Continue on next page
(Figure B)
11
22
33
POWER
SEEK
TUNE
PASS AIRBAG
LO
(Figure A)
(Figure C)
2
c
HI
LO
c
HI
Dash Disassembly 99-7422
Nissan Sentra 2007-2012 (without pocket door)
4. Remove (2) Phillips screws
securing the bottom of the radio
trim panel. (Figure D)
POWER
SEEK
TUNE
5. Unclip and remove the trim panel
at the top of the radio trim panel.
(Figure E)
6. Remove (2) Phillips screws
securing the top of the radio trim
panel. (Figure F)
7. Unplug and remove radio/trim
panel assembly. (Figure G)
(Figure D)
(Figure F)
8. Remove (4) Phillips screws
securing the radio brackets to the
trim panel and remove the trim
panel.
POWER
SEEK
TUNE
9. Remove (6) Phillips screws, 3 per
side, securing the factory brackets
to the radio/display assembly.
POWER
SEEK
Note: Retain the factory brackets
and display for possible use during
kit assembly.
POWER
SEEK
Continue to kit assembly
TUNE
(Figure E)
(Figure G)
3
TUNE
Kit Assembly 99-7422
Kit Preparation
1. Attach the (2) radio housing
brackets to the radio housing using
the supplied (2) carriage bolts and
nuts. (Figure A)
2. Secure the display into the
assembled radio housing/bracket
assembly using the factory
hardware. (Figure B)
Note: Display can be replaced
with Metra’s pocket, part number
88-00-7422 sold separately.
Continue to kit assembly
(Figure A)
(Figure B)
4
Kit Assembly 99-7422
DIN radio provision with pocket
1. Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking outward.
2. Slide the aftermarket radio into the
cage until it snaps into place.
3. Attach the radio housing trim plate
supplied with the kit.
Note: Display can be replaced
with Metra’s pocket, part number
88-00-7422 sold separately.
4. Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-connect
the negative battery terminal and
test the unit for proper operation.
5. Reassemble dash in reverse order
of disassembly.
(Figure A)
(Figure B)
5
Kit Assembly 99-7422
Double DIN radio provision
1. Re-Secure the display* to the
factory brackets using the factory
hardware. (Figure A)
2. Slide the Double DIN radio into
the factory brackets and secure
the unit to the brackets using the
screws supplied with the radio.
(Figure B)
3. Place the double DIN trim
plate over the face of the
aftermarket radio.
Note: Display can be replaced
with Metra’s pocket, part number
88-00-7422 sold separately.
4. Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-connect
the negative battery terminal and
test the unit for proper operation.
(Figure A)
(Figure B)
5. Reassemble dash in reverse order
of disassembly.
6
Notes
7
INSTALLATION INSTRUCTIONS FOR PART 99-7422
KNOWLEDGE IS POWER
REV. 1/27/2014 INST99-8231
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
METRA. The World’s best kits.™
1-800-221-0932
metraonline.com
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION