LCD MONITOR
User manual
IMPORTANT SAFETY INFORMATION
Table of contents
ENVIRONMENT
Important safety information
In The Box
Connections
Rear interface
Control Layout
How to connect your monitor
On-Screen Display (OSD) Operation
HDMI Input Configuration
VGA Input Configuration
2
4
4
4
5
5
6
7
8
Do not install the monitor outdoors or in any hostile environment. To
prevent fire or electric shock, do not expose monitor to rain or
moisture. Avoid placing the monitor in areas subject to extreme
temperature such as direct sunlight or near a heating
appliances/equipment (such as amplifiers, etc) as this may result in
overheating and damage.
This monitor is designed to be used in the office or home. Do not
subject it to vibrations, dust or corrosive gases.
To obtain a clear picture, do not expose screen to direct
illumination or sunlight. Using the monitor against a bright background
and where sunlight or other light sources shine directly on to the
monitor can increase eye fatigue
POWER CORD
Manufacturer reserves the right to upgrade the
product without notice!
Neither the monitor itself nor any other heavy object should rest
on the power cord.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles and the point where
they exit from the monitor.
Firmly grasp the plug when disconnecting the power cord. Do not pull
the power cord itself.
Do not modify or damage the cord. Damage to a power cord can cause
fire or electric shock.
This monitor is designed to operate on 100-240V AC supply. Take
caution in connecting it to the correct supply using the correct power
cord.
MOUNTING
1.
Always place the monitor on a secure table or have it properly mounted
to the wall. Do not hang anything on the monitor.
Ensure the monitor is located close to a power outlet that is easily
accessible, as removing the power cord is the only way to isolate power
2.
IN THE BOX
USING A WALL MOUNT
Caution: Any wall mount must bear a minimum of 5x the monitor’s net weight
to mount safely. The stand must be removed first before mounting this way.
1. Place the monitor face down on a surface that is soft, yet strong
enough to hold the monitor.
2. Use a screwdriver to remove the screws from the four holes on each
side of the bottom of the monitor’s base.
3. Make sure all cables are already connected to the monitor.
4. Follow the directions included with the wall mount to fix the monitor to
the wall.
STORAGE
1 x LCD Monitor
1 x AC adapter
1 x VGA cable
1 x Power cable
1 x User Manual
CONNECTIONS
Rear Interface
Unplug the monitor if it will not be used for a long period.
VENTILATION
Never cover or block the ventilation slots in the monitor. A minimum
distance of at least 10 cm should be maintained around the unit for
sufficient ventilation.
Never insert any foreign object, metal or liquid into the ventilation slots,
as this could result in fire or electric shock.
Avoid installing a DVR or other equipment too close to the
monitor. Keep such equipment at least 30 cm away from the monitor.
WATER AND MOISTURE
The monitor should not be exposed to any moisture or liquid.
Do not use the monitor near water.
Do not touch the monitor or cable with wet hands as this may cause
electric shock or damage.
DC:
Only use the 12v DC power supply included with the monitor.
HDMI: (High-Definition Multimedia Interface) Supports digital video and audio
connections.
VGA:
15 pin D-sub cable for standard VGA connection.
CLEANING
3.
Unplug the unit from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a dry soft lint-free cloth for
cleaning. If dust is persistent, wipe with a slightly damp cloth.
4.
CONTROL LAYOUT
2. Connecting using VGA
The control buttons are located on the right hand rear side of the monitor.
5keys series (19.5”,21.5”)
SOURCE
-
+
MENU
POWER
7keys series (23.6”,27”)
SOURCE -
+
∨
∧
MENU POWER
SOURCE:
Selects input mode – HDMI , VGA.
MENU:
Access to the On Screen Display (OSD) menu.
＋ and －:
POWER:
controls up/down, confirm input source selection and
navigation in the OSD.
Turns the monitor on or off.
HOW TO CONNECT YOUR MONITOR
1. Connecting using HDMI
Connect one end of a HDMI cable (optional) to the HDMI connector on
the rear of the monitor, and the other to the HDMI out connector on the
PC/DVR. This connection will support both video and audio
transmission.
Connect power to the monitor and video source, and switch on. Using
the SOURCE button, press repeatedly until ‘HDMI’ is highlighted on the
display at the top of the monitor's screen, and press ‘+’ to select.
5.
Connect one end of a 15-pin monitor cable to the VGA connector on
the monitor and the other end to the PC/DVR. Note - if your PC/DVR
connector isn't 15-pin D-sub you may need an adapter to connect
with this cable.
If audio is required, connect one end of the 3.5 mm stereo audio cable
(sometimes referred to as 1/8" stereo jack) to the PC Audio IN
connector on the back of the monitor and the other end to the audio
output on the PC/DVR.
Connect power to the monitor and video source, and switch on. Using
the SOURCE button, press repeatedly until ‘VGA’ is highlighted on the
display at the top of the monitor's screen, and press ‘+’ to select.
Ensure all cable connections are secure - tighten all cable screws.
Movement and vibration may dislodge cables that are improperly
connected. Route all wiring and cabling away from any heat sources and
sharp metal edges to avoid damage.
BASIC ON-SCREEN DISPLAY SETUP
1. To access the OSD Menu press ‘MENU’.
2. Use the ‘＋’ or ‘－’ buttons to select the required menu item, then press
the ‘SOURCE’ button to select the Sub menu.
3. Continue to use the ‘SOURCE’ button to highlight the required field, then
press ‘＋’ or ‘－’ to adjust the setting.
4. Press the ‘MENU’ button to return to previous menu.
5. Press the ‘MENU’ button again to exit the OSD Menu completely.
6. N.B. To Lock or Unlock OSD settings after set up.
Press and hold "menu" button for 5 seconds.
6.
The layout of the OSD will change depending on the input
that is selected.
HDMI - Input Configuration
1. Picture
LANGUAGE:
H-POSITION:
V-POSITION:
DURATION:
BACKLIGHT:
MEM-RECALL:
Select preferred language for OSD.
(En/Ch/Ger/Fr/Sp/It/Pt/Pl/Ru)
(0-100) Set the horizontal position of the OSD.
(0-100) Set the vertical position of the OSD.
(5-60) Set seconds for the OSD to automatically close.
Set power level in use by backlight (HIGH/MID/LOW)
Restore all factory defaults.
3.Function
CONTRAST:
BRIGHTNESS:
HUE:
SATURATION:
SHARPNESS:
COLOR TEMP:
PICTURE MODE:
2.OSD
7.
(0–100) Set the difference between the light and dark
areas of the picture.
(0–100) Set how bright the display is.
-50 to +50 (only available if NTSC)
(0-100)
(0-100)
Select the color temperature. (Normal/Warm/Cool)
Select defaults or save user setting. (
User/Standard/Soft/Vivid)
HSTART:
HSIZE:
VSTART:
VSIZE:
Set left alignment point of image.
Set horizontal size of image.
Set lower alignment point of image.
Set vertical size of image.
VGA - Input Configuration
1.
Picture
8.
CONTRAST:
BRIGHTNESS:
COLOR TEMP:
(0–100) Set the difference between the light and dark
areas of the picture.
(0–100) Set how bright the display is.
Select the color temperature Menu.
3.
Geometry
H-POSITION:
V-POSITION:
CLOCK:
COLOR TEMP:
USER - R:
USER - G:
USER - B:
2.
Select color temperature preset.
Set RED color level.
Set GREEN color level.
Set BLUE color level.
OSD
PHASE:
AUTO ADJUST:
Set horizontal image position.
Set vertical image position.
Manually adjust clock synchronisation.
(If the clock setting of your image is not fine-tuned, you
may observe periodic vertical bars of video noise on
your image. These bars of noise are usually adjusted
out when an Auto Configuration is performed. If the
bars of noise are still present, this setting can be used
to remove them.
If the phase of your monitor is not fine-tuned, you may
observe the image being unstable in the horizontal axis.
Use this option to manually correct.
Perform an automatic configuration of the Phase, Clock,
vertical and horizontal position.
END
LANGUAGE:
H-POSITION:
V-POSITION:
DURATION:
BACKLIGHT:
MEM-RECALL:
9.
Select preferred language for OSD.
(En/Ch/Ger/Fr/Sp/It/Pt/Pl/Ru)
(0-100) Set the horizontal position of the OSD.
(0-100) Set the vertical position of the OSD.
(5-60) Set seconds for the OSD to automatically close.
Set power level in use by backlight (HIGH/MID/LOW)
Restore all factory defaults.
10
">
