Before Installation
Ensure selected wall for installation is free of plumbing or any other obstructions.
US RETRO BOX
Box Contents
SURFACE MOUNT
INSTALLATION GUIDE
More info at iportproducts.com
Electrical Wall Box for the PoE Splitter
The PoE Splitter can be used with US, UK
and Euro single gang electrical boxes.
The recommended depth for the UK electrical
box is a minimum of 1.4” (35mm) and the
Euro wall box is a minimum of 1.85” (47mm).
An open double gang electrical box may be
used to allow for flexible wire management.
(1) Installation Guide
(1) Surface Mount Bezel (a)
(1) Mounting Bracket (b)
(1) Suction Cup (c)
(4) Mounting Screws (d)
(1) Security Tool (e)
System Components
(Sold Separately)
PRIOR TO INSTALLATION,
PLEASE REFERENCE POWER
AND WIRING GUIDE FOUND
IN THE POE SPLITTER BOX
(1) PoE Splitter (70718) (f)
(1) PoE Injector (70719) (g)
(International Adapters Included)
Hardware Requirements
Hardware required for each application scenario is shown below. For brick & mortar, concrete, and glass
applications, please view our application note for installation on our website, www.iportproducts.com
DRYWALL
SOFT WOOD
Use provided
hardware (use a
Phillips hand
screwdriver)
Use provided
hardware (use a
Phillips hand
screwdriver)
HARD WOOD
BRICK & MORTAR
Use brick & mortar
Drill pilot holes &
use provided hardware anchors & screws
(not provided)
(use a Phillips
machine screwdriver)
1
When removing the Surface Mount (a) bezel from its
box, the bezel will be attached to the (b) mounting
bracket. To decouple the (a) bezel from the (b)
mounting bracket, place the (a) bezel face up on a
flat and smooth surface. With one hand, hold the (b)
mounting bracket in place. With your opposite hand,
lift the right edge of the (a) bezel and then the left to
decouple the magnets. This will help avoid bending of
the metal, and prevent any damages to the (a) bezel
or (b) mounting bracket.
CONCRETE
GLASS
Use concrete
anchors & screws
(not provided)
Use Surface Mount
glass mounting kit
(sold separately)
(70720)
2
Locate the ideal mounting area. For retrofit
installation, locate an existing low-voltage electrical
box. For new construction, choose a location for
an electrical box. We recommend installing the (a)
bezel in landscape orientation, but it can also be
installed in portrait orientation. NOTE: A single gang
electrical box allows you to use the Surface Mount in
portrait or landscape orientation, and a double gang
electrical box allows you to use the Surface Mount in
a landscape only orientation.
US
EURO METAL BOX
EURO PLASTIC BOX
UK
EURO
For Advanced Installation
iPort offers an elegant solution to integrate iPad onto any surface. For advanced surface
installation applications such as masonry, concrete, and glass, please view our application
note for installation on our website, www.iportproducts.com. For drywall and wood
installation, please proceed to the installation steps noted below.
Preparation for Installation
Choose your power/wiring scenario:
Accessories required for
each power/wiring scenerio
BEZEL
PoE
PoE
SPLITTER INJECTOR
PoE Switch Powered
B
S
24V Powered
B
S
B
S
Receptacle Powered
S PoE Splitter (sold separately)
The PoE splitter is designed to provide the
necessary power to the iPad’s Lightning
Connector from a PoE or direct 24V power
source. For more detailed information,
see enclosed diagrams.
i PoE Injector (sold separately)
The PoE injector is designed to provide
power via PoE (IEEE 802.3af) and is required
if there is no other PoE or 24V power source.
i
3B
3A
Install the (b) mounting bracket on the wall with
the (b) bracket surrounding the electrical box.
Use the center lines as a guide to install the (d)
mounting screws. Our specialized (d) mounting
screws act as anchors and screws when mounting
on a drywall or wood surface.
Using the recommended screwdriver and (d)
mounting screws, install the first screw in the
upper left-hand corner.
SURFACE MOUNT INSTALLATION GUIDE
3C
4
Level the (b) mounting bracket over wiring
location and fasten (b) bracket with the remaining
(d) screws. Lining up the (d) mounting screws
with the engraved center lines provided on the
(b) bracket will allow you optimal adjustability.
The (b) mounting bracket is now in place.
Place the Surface Mount (a) bezel face down on
a flat and smooth surface with the iPort logo on
the left.
7
5
Plug the iPad’s lightning to USB cable directly
into the iPad. Position the iPad facedown into the
(a) bezel with the iPad cable on the left. Carefully
wrap the iPad cable around the metal loop located
on the (a) bezel. To lock the iPad in place, deploy
the second and third toggles on the right side of
the Surface Mount (a) bezel. The first top-right
toggle is a power button extension.
6
Connect the USB connector to the USB port
located on the (f) PoE splitter. Tightly wrap the
remaining iPad cable around the (f) PoE splitter.
Leave enough slack on the iPad cable to place (f)
PoE splitter into the electrical box.
9
Removal
To lock the Surface Mount in place, use the (e)
security tool provided to engage the security
locks. When the bezel is in landscape orientation,
the security holes are located on the top-right
and bottom-left of the bezel. Rotate the (e)
security tool counter-clockwise to engage the
locks, and clockwise to unlock the Surface Mount
(a) bezel from the (b) mounting bracket.
The (c) suction cup (provided) is used to remove
the iPad and (a) bezel from the (b) mounting
bracket. Once the (a) bezel is unlocked from the
(b) mounting bracket, depress the (c) suction cup
on the corner of the iPad screen and carefully pull
the iPad from the wall, while the other hand is
supporting the opposite side of the (a) bezel.
8
LOCK
LOCK
Connect the appropriate power source identified
in the Power and Wiring Guide (found in (f) PoE
splitter box). Place the PoE splitter into the single
gang box located in the wall with the iPort logo
facing out. NOTE: If you need to remove the
(f) PoE splitter from the wall box, you can use
needle-nose pliers to grab onto holes provided
on the front of the (f) PoE splitter.
With the iPad home button facing left or right,
the Surface Mount will attach to the (b) mounting
bracket with internal magnets.
33-7458
08.28.15
">
