ACD-3100 QIG 090330
1-channel MPEG-4 Video Decoder
ACD-3100
Ver. 090330
Quick Installation Guide
11
1.1
Getting Started
PACKAGE CONTENTS
ACD-3100
Warranty Card
Product CD
Terminal Blocks & Screws
Power Adaptor (Option)
1-1
1.2 PHYSICAL DESCRIPTION
Read the following information to familiarize yourself with the video Decoder, and make
particular notes of where the connectors and LEDs are located.
1.
Action LED Indicator
The LED will light up after IP device has successfully completed the boot
process.
2.
Serial Port LED Indicator
LEDs indicating when serial port is active.
3.
Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Using a suitable pointed object, press and continue to hold the
Reset Button depressed. While continuing to hold the reset button
depressed, reconnect the power cable.
Step 3: Keep holding the reset button depressed around 6 seconds, release
the reset button. The unit will start up with factory default settings.
4.
Terminal Blocks Pin 1~6
The IP device supports two alarm input and two alarm output. DI: Logic
Level 0: 0~0.4V; Logic Level 1: 3.3~30V
DO: Logic Level 0:
0.1~0.6V; Logic Level1: 2.4~5V
Please find Support package” TS-00045” for details.
PIN
1
2
NAME
DESCRIPTION
DO1 Digital Output 1
DO2 Digital Output 2
1-2
3
4
5
6
5.
GND
DI1
DI2
GND
Ground Pin
Digital Input 1
Digital Input 2
Ground Pin
Terminal Blocks Pin 7~12
Pin 7~10: RS232/422/485. Default mode is RS-485
Pin 11~12: DC 12V power input
PIN
NAME
7
8
9
10
11
Tx+
TxRx+
Rx12V
12
GND
DESCRIPTION
RS-485
RS-422
RS-232
D+
Tx+
Tx
DTxRx+
Rx
RxPower Input (DC +12V)
Ground Pin of Power Input &
RS-232
6.
Ethernet Port
The IP device connects to the Ethernet via a standard RJ45 connector.
Supporting NWAY, this IP device can auto detect the speed of local
network segment (10Base-T/100Base-TX Ethernet).
7.
Dip Switch for Serial Port
RS-485 or RS-422 pin define (default is RS-485)
RS-232 pin define
1-3
8.
Audio Input / Output
The IP device supports one audio input and output with earphone jack
9.
Y/C Output
Analog Video Output of Y/C Signal with S-Video Connector
10. Composite Output
Analog Video Output of Composite Signal with BNC Connector
1-4
1.3 CONNECT NECESSARY CABLES
Follow the procedures below to connect the video Decoder to the respective apparatuses.
1. The IP camera or other encoding devices as a video source
2. The video server or other encoding devices as a video source
3. Connect video server / IP camera and video Decoder to an Ethernet hub (RJ45 connectors)
4. Video Decoder is the receiver side
5. Connect a coaxial cable to TV monitor and display the video which encoded and transferred from
video server / IP camera
1-1
2
2
Quick Tour
This section guides you with a quick tour on our video Decoder.
2.1 Configure the video Decoder
2.1.1 Make sure network environment
Default IP of video Decoder is 192.168.0.200. Please make sure the video
Decoder and your PC are on the same network segment before running the
installation.
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 200 is
excepted.)
2-2
2.1.2 Open Internet Explorer with IP address
This section describes how to configure the video Decoder. The product administrator has
unlimited access to all setup windows and normal users can only watch the live images. The video
Decoder is configured under a standard browser (Microsoft Internet Explorer 6.0 or above).
Follow the procedures below to configure the video Decoder.

STEP1: Open a browser

STEP2: Enter the IP address of the video Decoder.
The default IP address is “192.168.0.200”

STEP3: Enter the Account name (factory default: Admin) and the Password (factory
default: 123456).

STEP4: Select the language of the video Decoder user interface. You can select from
English, Traditional Chinese, Simplified Chinese, Japanese and Spanish.

STEP5: Click the
again.
button to login or click the
2-3
button to re-enter
2.1.3 Set a new IP address
*IP Address : The IP address of the LAN interface. The default IP address is 192.168.0.200.
*Subnet Mask : The subnet mask of the LAN interface.The default subnet mask is 255.255.255.0
*Click
button
2-4
2.1.4 Select a video server / IP camera
This section tells you how to setup video server or IP camera’s video and streaming
settings.
*Source Type : Select your video source is Video Server or Quad Server.
*Connect Type : Select Multicast or TCP mode for connecting to a video server/IP camera.
*Variable FPS : Select variable FPS.
*TCP Connect IP : Set IP address of a video server / IP camera while Connect Type is TCP
Streaming.
*Multicast Connect IP: Set IP address of video server / IP camera while Connect Type is
Multicast streaming.
*Connect User Name : Set Login Name of video server / IP camera.
*Connect Password : Set Password of video server / IP camera.
*Click
button
NOTE: Check with your MIS department, if video Decoder and video
server/IP camera are setting in different VLANs, please connect to WAN
2-1
port.
2.1.5 Click Save Reboot to restore all settings and please wait about 30 seconds
for system reboot.
2-2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement