Triple 2RU Rack Mount
HD LCD Monitor
User Manual
Product introduction:
Thank you for using our Triple Rack Mount Color LCD Monitor.
This monitor adopts advanced integrated circuits and special TFT
LED panel, which makes it low power consumption, stable
performance, no radiation etc. This monitor is with HDMI, 3G-SDI,
CVBS and AUDIO input, HDMI, 3G-SDI, CVBS output, Stereo
headphone etc. It has a wide range of application, casing compact,
simple operation, and strong compatibility. The advanced features
contain Screen Marker, Pixel to Pixel, Image Flip, and Color
Temp.etc
To insure best use of the unit, please read the
user's manual carefully.
CAUTION
1. Please use the qualified power adapter to charge.
2. Do not expose this product to direct sunlight, heat or
humid Conditions
3. Keep away from strong light while using this product so
as to obtain the clearest and the most colorful picture.
4. Please avoid heavy impact or drop on the ground.
5. Do not use chemical solutions to clean this unit. Please
simply wipe with a clean soft cloth to keep the
brightness of the surface.
6. In order to avoid damaging the product, please do
not take apart or repair the unit by yourself without
adjustable component in the unit by professional
staff.
1
Features
● Triple rack mount LCD monitor, compact thin and
lightweight design, which make it suitable for installing
where the space is limited and also could be installed in
the standard 19-inch rack.
● Three-color
Tally indicator.
● With VIDEO, AUDIO, HDMI, 3G-SDI input, suitable for a
variety of signals.
● Custom buttons, could set the custom F button function
as customers operating habit.
● With advanced functions like Center Marker, Safe Frames,
Check Field, Focus Assist, Aspect Ratio, Image Flip, P2P,
Image Freeze, etc.
Contents
1. Product description ------------------------------- 3
2. Monitor operation instruction ------------------ 6
3. Technical Parameters --------------------------- 13
4. Trouble shooting ---------------------------------- 14
2
1. Product description
1.1 Front panel description (One of the them)
1. MODE: Signal input selection.
2.
<: Volume down. In menu operation, it is for the
adjustment of the set item.
3.
>:Volume up. In menu operation, it is for the adjustment
of the set item.
4. MENU:Menu button
5. ∧/F1:No menu display, it is F1 button, when enters into
menu
bar, it is for the up item selection.
6. ∨/F2:No menu display, it is F2 button, when enters into
menu bar, it is for the down item selection.
3
7.
:On/Standby button
8.
:Earphone jack
9. TALLY indicator.
1.2 Rear panel description
1.DC power input port.
2. 4-pin XLR DC12V power input.
4
3. 3G/SDI:input & output
4. CVBS: input & output
5. AUDIO:Audio input L / R
6. HDMI:input & output
7. TALLY indicator input
#1
#2
8. USB program upgrade port
5
#3
2. Monitor operation instruction
Connect DC12V power to our monitor, the three displays light,
and then customers could operate the corresponding display
screen button on the panel.
2.1 Monitor button instruction
Corresponding display screen On/Standby button
MODE
Signal input selection
MENU
Menu button
>
Earphone volume up.
In Menu operation, it is for menu bar
selection.
In secondary menu, it is as function selection or
increase the value of the analog.
<
Earphone volume down.
In menu operation, it is for menu bar
selection.
In secondary menu, it is as function selection or
decrease the value of the analog.
∧/F1
No menu display, it is F1 custom button.
After enter into secondary menu operation, it is for
the up item selection.
∨/F2
No menu display, it is F2 custom button.
6
In menu operation, press<,>button to select
, then press ∨/F2 button to enter
into the secondary menu.
In secondary menu operation, it is for the down
item selection.
F1/ F2
Custom button, select F1/ F2 in F menu, then
press>or<button to pop-up F button function and
select (Center Marker, Safe Frames, Check Field,
Focus Assist, Aspect Ratio, Image Flip, P2P,
Image Freeze), then use ∧/F1 or ∨/F2 button to
set one of them as F1 button function, press
“MENU” button to confirm, and then press ∨/F2
button to enter F2 button custom operation.
2.2 Menu instruction
Press MENU button to pop-up menu, and press<or>button
to enter menu selection, then press∨/F2 button to enter
secondary menu, and then use ∧/F1 or ∨/F2 button to select
the menu item, after enter into secondary menu, use>or<
button to adjust item parameters, press MENU button to exit.
7
Image Color
※ Pic. Mode: Standard, Dynamic, Mild, User.
Select “User” to adjust Brightness, Contrast, Saturation
Sharpness according to the site situation.
※ Brightness: To adjust image's brightness.
※ Contrast: To adjust the brightest and the darkest ratio
of the image, please note the sense of picture will
make the picture lose the color when adjust proportion
too high or low.
8
※ Saturation: To adjust color concentration.
※ Sharpness: Also called ‘Resolution’, is an indicator for
the image plane definition and image edge sharpness.
If sharpness is higher, then the details contrast on the
image is higher, the image is more clearly.
※ Color Temp.: 6500, 9300, User. When select “User”,
adjust the R/G/B to meet the different user's requirement
for the different Color Temp.
※ Tint: On NTSC video mode, color tint is adjusted by
Tint.
Setting
● Menu of Page One
※ Language: Language for OSD:
English, 中文, Español, Português,
Français, Nederlands, Deutsch, 日本語
※ Aspect Ratio: To change the aspect ratio
Panorama, Just Scan, Zoom 1, Zoom 2, 16:9, 4:3 , Autom
9
※ No Signal: Color options of screen background when no
signal: Blue Screen, Red Screen, Green Screen, Black
Screen, White Screen
※ OSD Trans.: To adjust the level of transparent.
※ OSD H: To adjust the OSD position in horizontal.
※ OSD V: To adjust the OSD position in vertical.
※ Zoom All:Select this function and use “<” or “>” button
to adjust the image to Zoom In or Zoom Out separately.
※ OSD Time:Menu display time selection:
30s ,20s、10s, Off.
●Menu of Page two
※ U/D Zoom: Press “<”or “>”button, to adjust the
proportion of the image Up and Down to Zoom In or
Zoom Out.
※ L/R Zoom Press “<”or “>” button, to adjust the
proportion of the image Left and Right to Zoom In or
10
Zoom Out.
※ USB Upgrade: When need to upgrade the native data
application software, copy the file to the U disk, then
through the USB cable to connect with upgrade USB port,
press “>”key to confirm. After the upgrade, monitor will
automatically restart. Do NOT plug a USB cable into this
connector without contacting the factory.
※ Reset: Press “>” button, back to original setting.
Function
※ Center Marker: To set center mark (cross mark) display.
※ Safe Frames: To adjust screen marker
(off, 96%, 93%, 90%,85%, 80%, 2.35:1)
※ Image Freeze: The current picture still (capture function)
※ Image Flip: The H_V Flip, H Flip, V Flip of the image
around flip.
11
※ Check field: To switch among Color, Mono, Red, Green,
Blue.
※ P2P: The display mode makes the resolution of the
image consistent with display of the physical resolution.
※ Focus Assist:Under HDMI input, select this function,
Peaking (Superimpose red highlight over parts of the
monochrome image in focus), could be used as focus
auxiliary function in camera viewfinder.
Shortcut button setting
※ F1:Custom button, Choose F1, press“<” or “>”button to
pop-up (Center Marker, Safe Frames , Check Field,
Focus
Assist, Image Freeze, Aspect Ratio, Image Flip ,
P2P, Image Freeze) and use “∧/F1”or “∨/F2” to set one
of them as definition function. Press “MENU” to confirm.
※ F2:Custom button, see F1
12
3. Technical parameters
Panel Size
5.0inch
Panel Type
TFT LCD
Resolution
800×480×3(RGB)
Backlight
LED
Dot Pitch
0.045(W) x 0.135 (H) mm
Aspect Ratio
16:9
Brightness
500cd/㎡
Contrast
500:1
Response Time
TON=10ms; TOff=15ms
Viewing Angle
70°/70°(L/R) 50°/70°(U/D)
Input Signal
HDMI/ 3G-SDI/ Video/ Audio(L/R)
Output signal
HDMI/ 3G-SDI/ Video
Color Video Format
PAL-4.43 / NTSC-3.58
HDMI Support Format
480i /480p /576i /576p
720p (60/59.94/50/30/29/25/24/23.98)
1080i (60/59.94/50)
1080p(60/59.94/50/30/29.97/25/24/24fps/23.98/23.98fps)
SDI Support Format
480i/576i
720p(60/59.94/50/30/29/25/24/23.98)
1080i(60/59.94/50)
1080p(60/59.94/50/30/29.97/25/24/24fps/23.98/23.98fps)
Headphone Output
Stereo headphone output 3.5 mm interface
Input Voltage
DC:9.0~24.0V
Power Consumption
≦25W
Unit Size (mm)
482.6Lx88Hx34D mm
Unit Weight
≈1570g
Working Temperature
-20~55℃
Storage Temperature
-30~65℃
13
4. Trouble Shooting
4.1 Only Mono or Single color picture:
① Please check Saturation, Brightness &Contrast adjustment.
② Please check monitor color from the menu "Check Field" is in
Mono image or in other single color state.
4.2 NO image after put on the power
① Check if signal cable connection is in good condition, also need
to check if the monitor is synchronized with the input signal,
press “MODE” button to have a try.
② Make sure to use the standard adapter to connect the monitor.
4.3 No Sound
① Volume control did not open, can press the volume button and
try increasing the volume.
② Check the AUDIO input and ensure there is AUDIO signal.
■ Remark:
★If there are still other problems, please contact with our related
technical persons.
★If there are changes without prior notice.
14
">