PUMCM - Module Type Tem Controller(Enhanced Communication Module)(TN1PUMCMc-E)

PUMCM - Module Type Tem Controller(Enhanced Communication Module)(TN1PUMCMc-E)
ECNO 1162
INPTN5A0202-E
2-2
-- After mounting modules onto DIN rails, make sure to fasten it firmly by pushing up
the locking tabs.
-- When connecting modules, first, connect them with release of all modules’ locking
tabs, and then push all of them up to lock.
-- Make sure to turn the power OFF, when removing the front terminal block from the
main body or removing the main body from the base part.
-- In order not to prevent heat dissipation, do not block the air vents on the top and bottom of the equipment.
-- For mounting / dismounting modules to / from DIN rails, space more than 30mm
should be provided.
-- Use attached screws to the equipment only.
INPTN5A0201-E
Please Read First (Safety Warnings)
Please read this section thoroughly before using and observe the mentioned safety
warnings fully.
Safety warnings are categorized as "Warning", "Caution" or "Risk of Electrical Shock".
Warning
Improper use of the equipment may result in death or serious injuries.
Caution
Improper use of the equipment may cause injury or property damage.
2-3
Warning
1-1
Installation and Wiring
2-4
Ambient humidity
90% RH or below (with no condensation)
Vibration
10 to 70Hz less than 9.8m/s² (1G)
Warm-up time
30 min. or more
IEC1010-1: degree 2
• The insulation class of the equipment is as below. Before installing, confirm that the
insulation class for the equipment meets usage requirements.
Power source
Loader communication
Functional insulation (AC1000V)
F012
E
RED
Blinking (0.4-sec.
periods):
No communication
with any modules. (
Inter-module communication FAULT)
Blinking (0.1-sec.
periods) :
Executing initial polling
ON: No communication with PLC (InterPLC communication
FAULT)
(*Note 1)
ORANGE
–
SW No.
ON: Inter-module
communications being
sent
1
2
3
4
5
Blinking (0.4-sec.
period):
System FAULT
ON: Normal operation
BUS
RX1
ON: The inter-module
communications being
received
ON: RS-232C being
received
–
–
–
6
ON: RS-232C /
RS-422 being sent
TX1
–
RX2
RS422 being received
–
–
TX2
–
–
–
*Note1 The cause of system FAULT: EEPROM FAULT, rotary SW FAULT, Dip SW
FAULT.
--The base part
Mounting screw hole
Module connector
(Connect modules laterally)
Module connector
Power terminal block
See [Wiring]
Mounting screw hole
See [Installation]
Locking tab
Setting
--Station Nunbers Setting
The station number configuration switch must be set to “0”.
(Communications with PLC is not possible with any setting other than “0”.)
PWR
PUM-C
LOADER
BUS
STATION
345
RX1
TX1
STATION
RX2
TX2
345
7 8 9A
Pollution level
PWR
GREEN
7 8 9A
IEC1010-1: class II
Others cautions
LED Name
6
Installation category
2-5
-- Do not wipe the equipment with organic solvent, such as alcohol or benzene, etc.
Use a neutral cleaning agent for cleaning it.
-- Do not use mobile phones near the equipment (within 50cm). Otherwise the malfunction may result.
-- The use of the equipment near radios, TVs, or wireless devices may cause malfunctions.
-- After turning the power ON, it needs 5 to15 sec. until it starts communication.
-- Prior to wiring / connecting the equipment, always take a countermeasure against
static electricity (ESD).
Display LED
Six LED lamps indicate the following operation conditions.
6
-10 to 50 degree C
Error Operation
-- The alarm function does not work properly when an error occurs unless the correct
settings are made. Make sure to verify its setting prior to starting operation.
• This equipment intended to be used under the following conditions.
Ambient temperature
Cautions for Wiring
-- For wiring to the terminal block, use solderless terminals of screw size M3.
The screw size of the terminal block: M3 × 7 ( with a square washer)
Cramp torque: 0.78N-m (8kgf-cm)
-- To avoid the influence of inductive noise, signal wires should be separated from electric power lines or load lines.
-- If you use RS-232C communication, use it with atatching the noise filter to AC power
line. (This is not necessary if implementating the complete preparation for noise of
power line.
-- To comply with CE marking (EMC), attaching ferritic cores to the communication
cable and the power supply cable is recommended.
isk of
R
that a risk of electrical shock is present and the associated
Electrical Indicates
warning should be observed.
Shock
1
Cautions when Mounting to Cabinets / DIN rails
Communication
behavior setting
E
Material No.
St. No. configuration switch
See [Setting]
F012
Material
name
Specification Catalog
Operating
Mitsubishi’s
instruction
PLC Programless Communication Module
User's manual
Tool
PUM
parameter
loader
345
I/O terminal block
See [Wiring]
F012
Content
Cautions when Installing
STATION
TX2
BCD
Related Information
Refer to "Module Type Temperature Controller Enhanced Communication Module
(Mitsubishi’s PLC Programless Communication) User’s Manual" for details about
the items described in this manual.
Temperature Controller Enhanced
Communication Module (PLC
Programless Communication)
1 Unit
Instruction Manual 1 Copy
2-1
For install in UL listed enclosure only.
Please avoid installing in the following locations.
-- Where the ambient temperature is beyond the range of 0 to 50 degree C when the
equipment is in use.
-- Where the ambient humidity is beyond the range of 45 to 85% RH when the equipment is in use.
-- With rapid temperature changes, leading to dew condensation.
-- Where corrosive gas (sulfide gas, ammonia, etc., especially) or farmable gas is generated.
-- With direct vibration or shock to the equipment.
-- Where contacts with water, oil, chemicals, steam or hot water.
(If the equipment gets wet, since there is a risk of electric leakage or fire, have it
inspected by Fuji distributor.)
-- With high concentration of atmospheric dust, salt or iron particles.
-- With inductive interference, resulting in static electricity, magnetic fields or noise.
-- In direct sunlight.
-- Where accumulation of heat due to radiant heat is generated.
-- A switch or circuit Breaker shall be included in the building installation.
Please be it in close proximately to the equipment and within easy reach of the operator, and mark it as the disconnecting device for the equipment.
The contents of this manual are subjected to change without notice.
This manual is compiled with possible care in the interests of accuracy, however,
Fuji Electric Systems shall not be held liable for any damages, including indirect
damage, caused by typographical errors, absence of information or use of information in this manual.
Confirming Specifications and Accessories
Caution
Loader communication port
TX1
RX2
1 2 3 4 5 6
CAUTION
2
LOADER
RX1
ON
Thank you for purchasing the Fuji module type temperature controller.
Once you have confirmed that this is the product you ordered, please use it in accordance with the following instructions.
For detailed information on operating this equipment, please refer to the separate
user’s manual.
In addition, please keep this instruction manual within easy reach of the actual person
using this equipment.
.
PUM-C
BUS
7 8 9A
INP-TN1PUMCMc-E
PWR
Display LED
6
Model: PUMCM
Set communication behavior by DIP switches on the back front of the module (SW1 to
SW6).
--Main unit
-- Turn OFF the power when installing or removing the equipment. It may cause shock,
abnormal operation, or equipment failure.
-- Periodic maintenance is recommended for continuous and safe use of this equipment.
-- Some parts installed on this equipment have a limited life and/or may deteriorate with
age.
-- The warranty period for this unit (including accessories) is one year with appropriate
use.
(Mitsubishi's programless communication)
Before using the product, confirm that it
matches the type ordered.
(Refer to page 4 for model codes.)
Confirm that all of the following accessories are included.
Maintenance
E
1-2
Enhanced Communication Module
BCD
Multi-loop module type Temperature Controller
--Communication behavior setting
Part names and functions
BCD
-- When using a AWG-16 cable, you should use the crimp terminal that material thickness is 0.9mm or less.
Instruction Manual (Installation)
Configuration range
"0" fixation
(Factory-set value= 0)
RS-232C communication
RS-422 communication
Functional insulation (AC500V)
-- In cases where damages or problems with this equipment may lead to serious accidents, install appropriate external protective circuit.
-- For damage and failure prevention of the equipment, provide the rated power voltage.
-- To prevent electric shock and equipment failure, do not turn the power ON until all
wiring is completed.
-- Before turning the power ON, make sure clearance space has been secured for
shock or fire prevention.
-- Do not touch the terminal while the machine is ON. There are risks of shock or equipment errors.
-- Never disassemble, convert, modify or repair this equipment. There are risks of
abnormal operation, shock or fire.
-- All of the wiring should be class 1 type wiring or the low voltage wires are routed
separately from the hazardous voltage wires to ensure separation of circuits.
-1-
-2-
Functions
ON
RS-422 communication mode
OFF
RS-232C communication mode
No function
No function
No function
No function
When turning the power ON, reset
the inter-PLC communication setNo function
ting to the factory-set value.
ECNO 1162
INPTN5A0202-E
2-2
-- After mounting modules onto DIN rails, make sure to fasten it firmly by pushing up
the locking tabs.
-- When connecting modules, first, connect them with release of all modules’ locking
tabs, and then push all of them up to lock.
-- Make sure to turn the power OFF, when removing the front terminal block from the
main body or removing the main body from the base part.
-- In order not to prevent heat dissipation, do not block the air vents on the top and bottom of the equipment.
-- For mounting / dismounting modules to / from DIN rails, space more than 30mm
should be provided.
-- Use attached screws to the equipment only.
INPTN5A0201-E
Please Read First (Safety Warnings)
Please read this section thoroughly before using and observe the mentioned safety
warnings fully.
Safety warnings are categorized as "Warning", "Caution" or "Risk of Electrical Shock".
Warning
Improper use of the equipment may result in death or serious injuries.
Caution
Improper use of the equipment may cause injury or property damage.
2-3
Warning
1-1
Installation and Wiring
2-4
Ambient humidity
90% RH or below (with no condensation)
Vibration
10 to 70Hz less than 9.8m/s² (1G)
Warm-up time
30 min. or more
IEC1010-1: degree 2
• The insulation class of the equipment is as below. Before installing, confirm that the
insulation class for the equipment meets usage requirements.
Power source
Loader communication
Functional insulation (AC1000V)
F012
E
RED
Blinking (0.4-sec.
periods):
No communication
with any modules. (
Inter-module communication FAULT)
Blinking (0.1-sec.
periods) :
Executing initial polling
ON: No communication with PLC (InterPLC communication
FAULT)
(*Note 1)
ORANGE
–
SW No.
ON: Inter-module
communications being
sent
1
2
3
4
5
Blinking (0.4-sec.
period):
System FAULT
ON: Normal operation
BUS
RX1
ON: The inter-module
communications being
received
ON: RS-232C being
received
–
–
–
6
ON: RS-232C /
RS-422 being sent
TX1
–
RX2
RS422 being received
–
–
TX2
–
–
–
*Note1 The cause of system FAULT: EEPROM FAULT, rotary SW FAULT, Dip SW
FAULT.
--The base part
Mounting screw hole
Module connector
(Connect modules laterally)
Module connector
Power terminal block
See [Wiring]
Mounting screw hole
See [Installation]
Locking tab
Setting
--Station Nunbers Setting
The station number configuration switch must be set to “0”.
(Communications with PLC is not possible with any setting other than “0”.)
PWR
PUM-C
LOADER
BUS
STATION
345
RX1
TX1
STATION
RX2
TX2
345
7 8 9A
Pollution level
PWR
GREEN
7 8 9A
IEC1010-1: class II
Others cautions
LED Name
6
Installation category
2-5
-- Do not wipe the equipment with organic solvent, such as alcohol or benzene, etc.
Use a neutral cleaning agent for cleaning it.
-- Do not use mobile phones near the equipment (within 50cm). Otherwise the malfunction may result.
-- The use of the equipment near radios, TVs, or wireless devices may cause malfunctions.
-- After turning the power ON, it needs 5 to15 sec. until it starts communication.
-- Prior to wiring / connecting the equipment, always take a countermeasure against
static electricity (ESD).
Display LED
Six LED lamps indicate the following operation conditions.
6
-10 to 50 degree C
Error Operation
-- The alarm function does not work properly when an error occurs unless the correct
settings are made. Make sure to verify its setting prior to starting operation.
• This equipment intended to be used under the following conditions.
Ambient temperature
Cautions for Wiring
-- For wiring to the terminal block, use solderless terminals of screw size M3.
The screw size of the terminal block: M3 × 7 ( with a square washer)
Cramp torque: 0.78N-m (8kgf-cm)
-- To avoid the influence of inductive noise, signal wires should be separated from electric power lines or load lines.
-- If you use RS-232C communication, use it with atatching the noise filter to AC power
line. (This is not necessary if implementating the complete preparation for noise of
power line.
-- To comply with CE marking (EMC), attaching ferritic cores to the communication
cable and the power supply cable is recommended.
isk of
R
that a risk of electrical shock is present and the associated
Electrical Indicates
warning should be observed.
Shock
1
Cautions when Mounting to Cabinets / DIN rails
Communication
behavior setting
E
Material No.
St. No. configuration switch
See [Setting]
F012
Material
name
Specification Catalog
Operating
Mitsubishi’s
instruction
PLC Programless Communication Module
User's manual
Tool
PUM
parameter
loader
345
I/O terminal block
See [Wiring]
F012
Content
Cautions when Installing
STATION
TX2
BCD
Related Information
Refer to "Module Type Temperature Controller Enhanced Communication Module
(Mitsubishi’s PLC Programless Communication) User’s Manual" for details about
the items described in this manual.
Temperature Controller Enhanced
Communication Module (PLC
Programless Communication)
1 Unit
Instruction Manual 1 Copy
2-1
For install in UL listed enclosure only.
Please avoid installing in the following locations.
-- Where the ambient temperature is beyond the range of 0 to 50 degree C when the
equipment is in use.
-- Where the ambient humidity is beyond the range of 45 to 85% RH when the equipment is in use.
-- With rapid temperature changes, leading to dew condensation.
-- Where corrosive gas (sulfide gas, ammonia, etc., especially) or farmable gas is generated.
-- With direct vibration or shock to the equipment.
-- Where contacts with water, oil, chemicals, steam or hot water.
(If the equipment gets wet, since there is a risk of electric leakage or fire, have it
inspected by Fuji distributor.)
-- With high concentration of atmospheric dust, salt or iron particles.
-- With inductive interference, resulting in static electricity, magnetic fields or noise.
-- In direct sunlight.
-- Where accumulation of heat due to radiant heat is generated.
-- A switch or circuit Breaker shall be included in the building installation.
Please be it in close proximately to the equipment and within easy reach of the operator, and mark it as the disconnecting device for the equipment.
The contents of this manual are subjected to change without notice.
This manual is compiled with possible care in the interests of accuracy, however,
Fuji Electric Systems shall not be held liable for any damages, including indirect
damage, caused by typographical errors, absence of information or use of information in this manual.
Confirming Specifications and Accessories
Caution
Loader communication port
TX1
RX2
1 2 3 4 5 6
CAUTION
2
LOADER
RX1
ON
Thank you for purchasing the Fuji module type temperature controller.
Once you have confirmed that this is the product you ordered, please use it in accordance with the following instructions.
For detailed information on operating this equipment, please refer to the separate
user’s manual.
In addition, please keep this instruction manual within easy reach of the actual person
using this equipment.
.
PUM-C
BUS
7 8 9A
INP-TN1PUMCMc-E
PWR
Display LED
6
Model: PUMCM
Set communication behavior by DIP switches on the back front of the module (SW1 to
SW6).
--Main unit
-- Turn OFF the power when installing or removing the equipment. It may cause shock,
abnormal operation, or equipment failure.
-- Periodic maintenance is recommended for continuous and safe use of this equipment.
-- Some parts installed on this equipment have a limited life and/or may deteriorate with
age.
-- The warranty period for this unit (including accessories) is one year with appropriate
use.
(Mitsubishi's programless communication)
Before using the product, confirm that it
matches the type ordered.
(Refer to page 4 for model codes.)
Confirm that all of the following accessories are included.
Maintenance
E
1-2
Enhanced Communication Module
BCD
Multi-loop module type Temperature Controller
--Communication behavior setting
Part names and functions
BCD
-- When using a AWG-16 cable, you should use the crimp terminal that material thickness is 0.9mm or less.
Instruction Manual (Installation)
Configuration range
"0" fixation
(Factory-set value= 0)
RS-232C communication
RS-422 communication
Functional insulation (AC500V)
-- In cases where damages or problems with this equipment may lead to serious accidents, install appropriate external protective circuit.
-- For damage and failure prevention of the equipment, provide the rated power voltage.
-- To prevent electric shock and equipment failure, do not turn the power ON until all
wiring is completed.
-- Before turning the power ON, make sure clearance space has been secured for
shock or fire prevention.
-- Do not touch the terminal while the machine is ON. There are risks of shock or equipment errors.
-- Never disassemble, convert, modify or repair this equipment. There are risks of
abnormal operation, shock or fire.
-- All of the wiring should be class 1 type wiring or the low voltage wires are routed
separately from the hazardous voltage wires to ensure separation of circuits.
-1-
-2-
Functions
ON
RS-422 communication mode
OFF
RS-232C communication mode
No function
No function
No function
No function
When turning the power ON, reset
the inter-PLC communication setNo function
ting to the factory-set value.
--Fixing with screws
When fixing the equipment on the wall with using screw, connect module base parts
first, which are intended to mount.
1. Decide the mounting position, referring to the
(30)
figure below for the mounting screw hole.
2-M3
Front screw terminal cover
(option)
Terminal block
30
(When attached/
detached to/from
the main unit)
STATION
base part
(When detached from
the main unit )
85
RX2
TX
6
50
RS‑232C
RX
SG
BCD
100
SDA
SDB
(3)
6.1
DIN rail
+0.2
30+0.7
RS‑422
Terminal
screw M3
Unit [mm]
Vacant
PUM-C
PWR
PUM-A
BUS
LOADER
COM
LOADER
STATION
STATION
345
OUT3
F012
345
OUT4
E
TX2
F012
26
16
27
27
17
28
28
18
29
29
19
30
30
20
Vacant
Crimp terminal size
Please prepare cables and crimp terminals of the size indicated below.
When using a AWG-16 cable, you should use the crimp terminal that material thickness is 0.9mm
or less.
Cable type
Power supply, output, others
PUM-A
COM
LOADER
LOADER
STATION
345
OUT2
OUT3
OUT4
STATION
F012
OUT4
PUM-A
COM
COM
F012
STATION
345
PUM-E
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
LOADER
STATION
F012
PWR
LOADER
345
789
A
F012
PUM-E
Cable size
0.25 to 1.25mm2 (AWG 22 to 16)
Wiring
In the case of RS-232C connection
Screw tightening torque
0.8 N•m
φ3.2mm
BCDE
BCD
Side connecting connector covers
(right & left 1 set)
-3-
* Material thickness
0.9mm or less.
345
E
OUT3
F012
OUT2
PWR
OUT1
E
F012
345
Size
0.25 to 1.25mm2 (AWG 22 to 16)
Communication unit
Pin No.
1
2
3
4
5
6
7
8
9
Signal
CD
RD(RXD)
SD(TXD)
ER(DTR)
SG
DR(DSR)
RS(RTS)
CS(CTS)
RI(CI)
Round-shaped solderless terminal
The equipment
Pin No.
21
22
23
24
25
26
27
28
29
30
Signal
TX
RX
SG
SDA
SDB
SG
RDA
RDB
-
Model code
Enhanced communication module (Mitsubishi’s PLC programless communication)
1
2
3
4
Terminating Resistance
5
6
7
8
9 10
Y Y 1 - 0
P U M
Contents
Module type
Enhanced communication module
Communication functions
Mitsubishi's PLC programless communication
Instruction Manual
Japanese
English
C
M
In the case of RS-422 connection
Communication unit
A
B
The equipment
Signal
Pin No.
Signal
SDA
SDB
RDA
RDB
SG
FG
21
22
23
24
25
26
27
28
29
30
TX
RX
SG
SDA
SDB
SG
RDA
RDB
-
Y-shaped solderless terminal
Model code (Optional)
1
2
3
4
5
6
7
8
A
A
A
L
0
0
0
0
2
3
4
1
P U M Z *
Terminating Resistance
Terminating resistance: 330Ω
*Both connection of RS-232C and RS-422 of the equipment can not operate at the same time.
Contents
DIN rail mounting endplate
Side connector termination cover (right & left 1 set)
Front face screw terminal cover
Loader connecting cable (RS232C)
General Specification
DIN rail mounting
endplate
6
345
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
789
E
STATION
E
30 or more
STATION
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
6
F012
COM
BCDE
PWR
LOADER
A
PUM-E
789
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
6
7 8 9A
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
BCDE
345
6
6
F012
E
26
Communication specifications :RS-232C and RS-422- compliance
The number of port
:1 port (specifying RS-232C / RS-422 by switch)
Communication protocol
:MC protocol Type5
Communication speed
:9.6k, 19.2k, 38.4k, 57.6k, 115.2k, 230.4kbps
Communication length
:RS232C: Max. 15m
RS422: Max. 1km (38.4kbps or less),
500m (57.61bps or less), 250m (115.2kbps or more)
Recommended cable: RS232C cable :KFPEV-SB 1P 0.5sq (equivalent to Fuji electric cable)
RS422 cable: KFPEV-SB 2P 0.5sq (equivalent to Fuji
electric cable)
Connecting method
:M3 screw terminal block
Specification
A
STATION
TX2
BCD
COM
OUT4
TX1
RX2
PWR
OUT1
BCD
PWR
LOADER
OUT3
LOADER
RX1
BCD
PUM-A
COM
OUT2
345
15
7 8 9A
-- Attaching the main unit to the base
part take the reverse procedure to
removing the main unit from the base
part.
-- Make sure the locking lever on the
main unit is fitted into the base part
after attaching.
PWR
OUT1
STATION
25
6
3. Detach the cutout on the lower end
of the back of the main unit from the
projection on the base part.
--Attaching the endplates
TX1
25
Communication Functions
Power terminal
2. Pulingl down the upper part of main
unit.
When mounting the equipment onto the DIN rails more firmly, use endplates (optional).
(When using endplates, use side connecting terminal covers as well.)
BCD
TX2
14
Crimp terminal
7 8 9A
1. Press the lock lever on the top of the
equipment.
3. Pull up the locking tab of the base
part to fasten the equipment onto
the DIN rails.
-- When connecting the equipment
after mounting it to the DIN rail,
do not pull the locking tab up at
this point yet.
RX2
24
Note: Power cables more than one should not be connected between power terminals.
6
DIN rail
PUM-C
BUS
7 8 9A
Hook
Locking tab
LOADER
24
--Connecting to PLC
PWR
6
3. After mounting modules to the DIN rails, pull
the all locking tabs up.
Modules are fastened to the DIN rails and to
each other on the same time.
4. The power supplies are connected each
other inside connected modules.
How to detach the base part
PUM-C
13
DC 24V (-)
--Mounting to DIN rails
RX1
23
DC 24V (+)
1. Pull down the locking tab of the
base part.
Hook the back part of the unit onto
the upper part of the DIN rails.
2. Push the unit towards the direction
of the arrow 2.
BUS
12
23
RS422
(2-piece terminal block)
RS232C
(D-sub 9P)
RS422
(2-piece plug-in connector socket
block)
11
OUT2
TX1
RX2
Locking tab
PWR
22
OUT1
RX1
Side
connector
DIN rail mounting
endplate
21
22
--Base part (power terminal)
PWR
F012
1. Check the locking tab is pulled down.
2. Connect modules by connecting module connectors with each other.
Vacant
30 or more
Make sure to secure clearance space more than 30mm (50mm is recommended)
above/below the equipment for.
RDB
8 9A
67
--Connecting modules
8 9A
67
--Cautions when mounting
E
(30)
(8)
5
Unit [mm]
BCD
Terminal screw M3
Main unit (When detached
from the base part)
RDA
2. Remove the main unit from the base part.
- See [How to detach the base part]
3. Connect the base part, and then pull all the locking tabs up to fasten.
4. Fixate the base part onto the mounting position on the wall with screws.
5. Attach the module main unit to the base part.
BCD
When mounted/
dismounted to/from
the DIN rail
SG
21
CH2
RS232C
(D-sub 9P)
RS232C
(D-sub 9P)
RS422
(2-piece plug-in connector socket
block)
6.0mm or less
F012
7 8 9A
E
6
TX2
345
E
TX2
(100)
88.5 0.2
(10)
STATION
1.5
LOADER
TX1
TX1
345
BUS
CH1
QJ71C24N
QJ71C24
QJ71C24N-R2
QJ71C24-R2
QJ71C24N-R4
RX1
RX1
RX2
PWR
PUM-C
BCD
LOADER
9±0.2
Communication port
Type
7 8 9A
PUM-C
BUS
--Front face terminal block
6
PWR
Connectable serial communication units in compliance with MELSEC-Q series
3.2mm
--Dimensions
Connectable device
Terminal Figure
6.0mm or less
Mounting
Power Supply
: DC24v±10%
Power Consumption
: Maximum 3.2W (135mA) [when 24Vdc is applied]
Dimensions
: 30(W)×100(H)×85(D) mm (excluding projection and terminal cover)
Weight
: Approx. 200g
Installation Method
: DIN rail mounting inside a cabinet / wall mounting with M3 screws
Ambient Temperature*
: -10 to 50 degrees C
Note:"Ambient temperature" mean the temperature underneath the
equipment inside the dvice or the cabinet where it is installed.
Ambient Humidity:
: 90%RH or less (no condensing)
System maximum modules: Up to max. 17 modules of any Model PUMA/B/C/CL/CM/V/N/T plus to
max 16 modules of Model PUME
System power
: 24V dc, 100W maximum, Class 2
Memory Backup:
: Backup by nonvolatile memory (EEPROM)
The number of rewriting: 100,000 times
International Sales Div
Sales Group
Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome,
Shinagawa-ku, Tokyo 141-0032, Japan
http://www.fujielectric.com
Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425
http://www.fujielectric.com/products/instruments/
-4-
--Fixing with screws
When fixing the equipment on the wall with using screw, connect module base parts
first, which are intended to mount.
1. Decide the mounting position, referring to the
(30)
figure below for the mounting screw hole.
2-M3
Front screw terminal cover
(option)
Terminal block
30
(When attached/
detached to/from
the main unit)
STATION
base part
(When detached from
the main unit )
85
RX2
TX
6
50
RS‑232C
RX
SG
BCD
100
SDA
SDB
(3)
6.1
DIN rail
+0.2
30+0.7
RS‑422
Terminal
screw M3
Unit [mm]
Vacant
PUM-C
PWR
PUM-A
BUS
LOADER
COM
LOADER
STATION
STATION
345
OUT3
F012
345
OUT4
E
TX2
F012
26
16
27
27
17
28
28
18
29
29
19
30
30
20
Vacant
Crimp terminal size
Please prepare cables and crimp terminals of the size indicated below.
When using a AWG-16 cable, you should use the crimp terminal that material thickness is 0.9mm
or less.
Cable type
Power supply, output, others
PUM-A
COM
LOADER
LOADER
STATION
345
OUT2
OUT3
OUT4
STATION
F012
OUT4
PUM-A
COM
COM
F012
STATION
345
PUM-E
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
LOADER
STATION
F012
PWR
LOADER
345
789
A
F012
PUM-E
Cable size
0.25 to 1.25mm2 (AWG 22 to 16)
Wiring
In the case of RS-232C connection
Screw tightening torque
0.8 N•m
φ3.2mm
BCDE
BCD
Side connecting connector covers
(right & left 1 set)
-3-
* Material thickness
0.9mm or less.
345
E
OUT3
F012
OUT2
PWR
OUT1
E
F012
345
Size
0.25 to 1.25mm2 (AWG 22 to 16)
Communication unit
Pin No.
1
2
3
4
5
6
7
8
9
Signal
CD
RD(RXD)
SD(TXD)
ER(DTR)
SG
DR(DSR)
RS(RTS)
CS(CTS)
RI(CI)
Round-shaped solderless terminal
The equipment
Pin No.
21
22
23
24
25
26
27
28
29
30
Signal
TX
RX
SG
SDA
SDB
SG
RDA
RDB
-
Model code
Enhanced communication module (Mitsubishi’s PLC programless communication)
1
2
3
4
Terminating Resistance
5
6
7
8
9 10
Y Y 1 - 0
P U M
Contents
Module type
Enhanced communication module
Communication functions
Mitsubishi's PLC programless communication
Instruction Manual
Japanese
English
C
M
In the case of RS-422 connection
Communication unit
A
B
The equipment
Signal
Pin No.
Signal
SDA
SDB
RDA
RDB
SG
FG
21
22
23
24
25
26
27
28
29
30
TX
RX
SG
SDA
SDB
SG
RDA
RDB
-
Y-shaped solderless terminal
Model code (Optional)
1
2
3
4
5
6
7
8
A
A
A
L
0
0
0
0
2
3
4
1
P U M Z *
Terminating Resistance
Terminating resistance: 330Ω
*Both connection of RS-232C and RS-422 of the equipment can not operate at the same time.
Contents
DIN rail mounting endplate
Side connector termination cover (right & left 1 set)
Front face screw terminal cover
Loader connecting cable (RS232C)
General Specification
DIN rail mounting
endplate
6
345
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
789
E
STATION
E
30 or more
STATION
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
6
F012
COM
BCDE
PWR
LOADER
A
PUM-E
789
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
6
7 8 9A
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
BCDE
345
6
6
F012
E
26
Communication specifications :RS-232C and RS-422- compliance
The number of port
:1 port (specifying RS-232C / RS-422 by switch)
Communication protocol
:MC protocol Type5
Communication speed
:9.6k, 19.2k, 38.4k, 57.6k, 115.2k, 230.4kbps
Communication length
:RS232C: Max. 15m
RS422: Max. 1km (38.4kbps or less),
500m (57.61bps or less), 250m (115.2kbps or more)
Recommended cable: RS232C cable :KFPEV-SB 1P 0.5sq (equivalent to Fuji electric cable)
RS422 cable: KFPEV-SB 2P 0.5sq (equivalent to Fuji
electric cable)
Connecting method
:M3 screw terminal block
Specification
A
STATION
TX2
BCD
COM
OUT4
TX1
RX2
PWR
OUT1
BCD
PWR
LOADER
OUT3
LOADER
RX1
BCD
PUM-A
COM
OUT2
345
15
7 8 9A
-- Attaching the main unit to the base
part take the reverse procedure to
removing the main unit from the base
part.
-- Make sure the locking lever on the
main unit is fitted into the base part
after attaching.
PWR
OUT1
STATION
25
6
3. Detach the cutout on the lower end
of the back of the main unit from the
projection on the base part.
--Attaching the endplates
TX1
25
Communication Functions
Power terminal
2. Pulingl down the upper part of main
unit.
When mounting the equipment onto the DIN rails more firmly, use endplates (optional).
(When using endplates, use side connecting terminal covers as well.)
BCD
TX2
14
Crimp terminal
7 8 9A
1. Press the lock lever on the top of the
equipment.
3. Pull up the locking tab of the base
part to fasten the equipment onto
the DIN rails.
-- When connecting the equipment
after mounting it to the DIN rail,
do not pull the locking tab up at
this point yet.
RX2
24
Note: Power cables more than one should not be connected between power terminals.
6
DIN rail
PUM-C
BUS
7 8 9A
Hook
Locking tab
LOADER
24
--Connecting to PLC
PWR
6
3. After mounting modules to the DIN rails, pull
the all locking tabs up.
Modules are fastened to the DIN rails and to
each other on the same time.
4. The power supplies are connected each
other inside connected modules.
How to detach the base part
PUM-C
13
DC 24V (-)
--Mounting to DIN rails
RX1
23
DC 24V (+)
1. Pull down the locking tab of the
base part.
Hook the back part of the unit onto
the upper part of the DIN rails.
2. Push the unit towards the direction
of the arrow 2.
BUS
12
23
RS422
(2-piece terminal block)
RS232C
(D-sub 9P)
RS422
(2-piece plug-in connector socket
block)
11
OUT2
TX1
RX2
Locking tab
PWR
22
OUT1
RX1
Side
connector
DIN rail mounting
endplate
21
22
--Base part (power terminal)
PWR
F012
1. Check the locking tab is pulled down.
2. Connect modules by connecting module connectors with each other.
Vacant
30 or more
Make sure to secure clearance space more than 30mm (50mm is recommended)
above/below the equipment for.
RDB
8 9A
67
--Connecting modules
8 9A
67
--Cautions when mounting
E
(30)
(8)
5
Unit [mm]
BCD
Terminal screw M3
Main unit (When detached
from the base part)
RDA
2. Remove the main unit from the base part.
- See [How to detach the base part]
3. Connect the base part, and then pull all the locking tabs up to fasten.
4. Fixate the base part onto the mounting position on the wall with screws.
5. Attach the module main unit to the base part.
BCD
When mounted/
dismounted to/from
the DIN rail
SG
21
CH2
RS232C
(D-sub 9P)
RS232C
(D-sub 9P)
RS422
(2-piece plug-in connector socket
block)
6.0mm or less
F012
7 8 9A
E
6
TX2
345
E
TX2
(100)
88.5 0.2
(10)
STATION
1.5
LOADER
TX1
TX1
345
BUS
CH1
QJ71C24N
QJ71C24
QJ71C24N-R2
QJ71C24-R2
QJ71C24N-R4
RX1
RX1
RX2
PWR
PUM-C
BCD
LOADER
9±0.2
Communication port
Type
7 8 9A
PUM-C
BUS
--Front face terminal block
6
PWR
Connectable serial communication units in compliance with MELSEC-Q series
3.2mm
--Dimensions
Connectable device
Terminal Figure
6.0mm or less
Mounting
Power Supply
: DC24v±10%
Power Consumption
: Maximum 3.2W (135mA) [when 24Vdc is applied]
Dimensions
: 30(W)×100(H)×85(D) mm (excluding projection and terminal cover)
Weight
: Approx. 200g
Installation Method
: DIN rail mounting inside a cabinet / wall mounting with M3 screws
Ambient Temperature*
: -10 to 50 degrees C
Note:"Ambient temperature" mean the temperature underneath the
equipment inside the dvice or the cabinet where it is installed.
Ambient Humidity:
: 90%RH or less (no condensing)
System maximum modules: Up to max. 17 modules of any Model PUMA/B/C/CL/CM/V/N/T plus to
max 16 modules of Model PUME
System power
: 24V dc, 100W maximum, Class 2
Memory Backup:
: Backup by nonvolatile memory (EEPROM)
The number of rewriting: 100,000 times
International Sales Div
Sales Group
Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome,
Shinagawa-ku, Tokyo 141-0032, Japan
http://www.fujielectric.com
Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425
http://www.fujielectric.com/products/instruments/
-4-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement