Dyna-Glo Delux KFA50DGD User's Manual And Operating Instructions

Add to My manuals
30 Pages

advertisement

Dyna-Glo Delux KFA50DGD User's Manual And Operating Instructions | Manualzz
INDOOR/OUTDOOR PRODUCTS
KEROSENE PORTABLE
FORCED AIR HEATERS
“USER’S MANUAL AND
OPERATING INSTRUCTIONS”
COMPLIES WITH UL733 AND
ANSI A10.10-1998
CAN/CSA/B140.0-03 AND CSA
B140.8-1967
MODEL : KFA50DGD, KFA75DGD, KFA125DGD
KFA170DGD, KFA210DGD
Before the first use of this heater, please read this USER’S MANUAL very
carefully. This USER’S MANUAL has been designed to instruct you as to
the proper manner in which to assemble, maintain, store, and most
importantly, how to operate the heater in a safe and efficient manner.
Please keep this manual for future reference.
CONSUMER : Retain this manual for future reference.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 877-447-4768 8:30 a.m. - 4:30 pm CST, Monday - Friday.
or email us at [email protected]
IMKFADG-GCU
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
DANGER:: IMPROPER USE OF THIS HEATER CAN RESULT IN SERIOUS INJURY OR DEATH
FROM BURNS, FIRE, EXPLOSION, ELECTRICAL SHOCK AND/OR CARBON
MONOXIDE POISONING.
WARNINGS:
1. RISK OF INDOOR AIR POLLUTION!
‡ Use this heater only in well ventilated areas. Provide at least a three-square foot (2,800 sq. cm.)
opening of fresh outside air for each 100,000 BTU/hr. of heater rating.
‡ People with breathing problems should consult a physician before using the heater.
‡ Carbon monoxide poisoning: Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness
and/or nausea. If you have these signs, the heater may not be working properly.
Get fresh air at once! Have the heater serviced. Some people are more affected by carbon monoxide than others.
These include pregnant women, persons with heart or lung disease or anemia, those under the influence of alcohol, or
those at high altitudes.
‡ Never use this heater in living or sleeping areas.
2. RISK OFBURNS/FIRE/EXPLOSION!
‡ NEVER use any fuel other than 1-K kerosene, #1 disel/fuel oil in this heater.
‡ NEVER use fuel such as gasoline, benzene, paint thinners or other oil compounds in this heater.
(RISK OF FIRE OR EXPLOSION)
‡ NEVER use this heater where flammable vapors may be present.
‡ NEVER refill the heaters fuel tank while heater is operating or is still hot.
while in operation. Do not touch. Keep children,
CAUTION: Hot
clothing and combustibles away from heater.
‡
‡
‡
‡
‡
‡
‡
‡
Minimum Clearances: Outlet: 8 feet (250cm) / Sides, top and rear: 4 feet (125cm)
NEVER block air inlet (rear) or air outlet (front) of heater.
NEVER use duct work in front or behind of heater.
NEVER move, handle, service a hot, operating or plugged in heater.
NEVER transport heater with fuel in it’s tank.
When used with an optional thermostat or if equipped with a thermostat heater may start at any time.
ALWAYS locate heater on a stable and level surface.
ALWAYS keep children and animals away from heater.
Bulk fuel storage should be a minimum of 25 ft. from heaters, torches, portable generators or other sources of ignition.
All fuel storage should be in accordance with federal, state or local authorities having jurisdiction.
3. RISK OF ELECTRIC SHOCK!
‡
‡
‡
‡
Use only the electrical power (voltage and frequency) specified on the model plate of the heater.
Use only a three-prong, grounded outlet and extension cord.
ALWAYS install the heater so that it is not directly exposed to water spray, rain, dripping water or wind.
ALWAYS unplug the heater when not in use.
PROPOSITION 65 WARNING: Fuels used in gas, wood-burning or oil fired appliances, and the
products of combustion of such fuels, contain chemicals known to the State of California to cause cancer,
birth defects and other reproductive harm.
MASSACHUSETTS RESIDENTS: Massachusetts state law prohibits the use of this heater in any
building which is used in whole or in part for human habitation. Use of this heating device in
Massachusetts requires local fire dept. permit (M.E.L.C. 148, Section 10A.)
CANADIAN RESIDENTS: Use of this heater shall be in accordance with authorities having
jurisdiction and CSA Standard B139.
NEW YORK CITY RESIDENTS: For use only at construction sites in accordance with applicable NYC
codes under NYCFD certificate of approval # 5034 and 5037.
1
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
CONTENTS OF USER’S MANUAL
ITEM
PAGE #
PRECAUTIONS - SAFETY GUIDE
1. INTRODUCTION
2. FEATURES
3. UNPACKING AND ASSEMBLY
4. KEROSENE (1-K OR NO. 1 FUEL OIL)
5. OVERVIEW OF HEATER DESIGN
6. FUELING YOUR HEATER
7. OPERATION
8. LONG TERM STORAGE OF YOUR HEATER
9. MAINTENANCE
10. REPLACING FUSE
11. TROUBLE SHOOTING GUIDE
12. WIRING DIAGRAM
13. SPECIFICATIONS
14. EXPLODED PARTS DRAWING
15. PARTS LIST
1
2
2
4
6
7
8
8
9
10
14
15
16
17
18&21&24
19,20&22,23&25,26
1. INTRODUCTION
Please read this USER’S MANUAL carefully. It will show you how to assemble, maintain, and operate the
heater safely and efficiently to obtain full benefits from its many built-in features.
2. FEATURES
Front Guard
Hot Air Outlet
Upper Shell
Handle
Fan Guard
Lower Shell
Fuel Tank
Side Cover
Lamp
Fuel Gauge
Fuel Cap
Thermostot Knob
(75DGD Model Only)
Power/Reset Switch
Power Cord
(Piggy Back, 75DGD Model Only)
Figure 1. KFA50DGD/75DGD MODELS
2
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
Front Handle
Rear Handle
Upper Shell
Hot Air Outlet
Shell Lower
Cord Wrap
Fuel Gauge
Fuel Cap
Side Cover
Lamp
Thermostot Knob
Room Temp. Display
(170DGD Model Only)
Power/Reset Switch
10” Flat Free Wheel
BTU Control Switch
Pressure Gauge
Fan Guard
Power Cord
(Piggy Back)
Fuel Drain Bolt
Figure 2. KFA125/170DGD MODELS
Front Handle
Upper Shell
Hot Air Outlet
Rear Handle
Shell Lower
Cord Wrap
Fuel Gauge
Fuel Cap
BTU Control Switch
Pressure Gauge
Fan Guard
Side Cover
Lamp
Thermostot Knob
Room Temp. Display
Power Cord
(Piggy Back)
Power/Reset Switch
Fuel Drain Bolt
10” Flat Free Wheel
Figure 3. KFA210DGD MODEL
3
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
3. UNPACKING AND ASSEMBLY
1. REMOVE THE HEATER AND ALL PACKING MATERIALS FROM THE BOX. (Fig. 4 and 5)
NOTE : Save the shipping carton and packing materials for future storage.
Wheel Support Frame
Wheel
Threaded Axle
Front Handle
Rear Handle
Handle
Cord Wrap
Hardware kit : HW-KFA1001
Hardware kit : HW-KFA1016
KFA50DGD
KFA75DGD
KFA125DGD
KFA170DGD
KFA210DGD
No
No
No
No
No
Yes
No
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
Figure 4. KFA50DGD/75DGD MODELS
Hardware Kit
HW-KFA1001
Handle
Figure 5. KFA125/170/210DGD MODELS
Screws
Nuts
Wheels
(10" Flat Free)
Flange Screws
Cap Nuts S Bushings
Cap Nuts L
Cord Wraps
Hardware Kit : HW-KFA1016
Front Handle
Rear Handle
Wheel Support Frame
Axle
4
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
2. ASSEMBLY
For KFA50DGD/75DGD Models only
(Assembly time for this product is 3 minutes)
Tools Required
‡ Medium Phillips Screwdriver.
1) Lift front guard for arrow direction and make
sure that guard’s wedged portion fits into the slit
hole on the upper housing.
2) Align the holes in the upper housing with two
mounting holes on the handle as shown in Figure 6.
3) Secure handle with Screws with provided.
Handle
Screw
Front Guard
Wedged Portion
Slit Hole
Figure 6. Assembling Handle & Cord Wrap
For KFA125/170/210DGD Models only (Assembly time for this product is 10 minutes)
Tools Required
‡0HGLXP3KLOOLSV6FUHZGULYHU
‡LQFKVRFNHWRUDGMXVWDEOHZUHQFK
Assembling Handle & Wheel and Cord Wrap
1) Slide threaded axle through the rear section of the wheel support frane.
2) Slide one axle bushing on to each side of the axle. Slide one wheel on to each side of the axle.
Attach one cap nut on to each side of the threaded axle and tighten well.
3) Place heater on wheel support frame. Align the holes on fuel tank flange with holes on wheel support frame.
4) Position the Handles on top of fuel tank flange.
Insert screws through handles, fuel tank flange and wheel support frames as shown in Figure 8 and
attach nut finger tight after each screw is inserted.
5) Align the hole on the handles with the mounting hole on the Cord Wrap.
Insert Screws through Cord Wrap, handles and attach nut finger tight after each screw is inserted.
6) After all screws are inserted, tighten nuts firmly.
5
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
Front Handle
Screw
Cap Nut S
Rear Handle
Hot Air Outlet
Cord Wrap
Flange Screw
Fuel Tank
Flange
Air Inlet
Wheel Support Frame
Nut
Threaded Axle
Wheel Bushing
Wheel
Cap Nut L
Figure 7. Assembling Handle, Wheel and Cord wrap
CAUTION : DO NOT OPERATE heater without support frame assembled to tank.
NOTE : Heater should be inspected before each use, and at least annually by a qualified service person.
4. KEROSENE (1-K)
For optimal performance of this heater, it is strongly suggested that 1-K kerosene be used. 1-K kerosene has
been refined to virtually eliminate contaminants, such as sulpher. Which can cause a rotten egg odor during
the operation of the heater. However, #1 diesel/fuel oil may also be used if 1-K kerosene is not available.
Be advised that these fuels do not burn as clean as 1-K kerosene, and care should be taken to provide more
fresh air ventilation to accomodate any added contaminants that may be added to the heated space.
KEROSENE SHOULD ONLY BE STORED IN A BLUE CONTAINER THAT IS CLEARLY
MARKED “KEROSENE”. NEVER STORE KEROSENE IN A RED CONTAINER.
Red containers are associated with gasoline.
NEVER store kerosene in the living space. Kerosene should be stored in a well ventilated place outside the
living area.
NEVER use any fuel other than 1-K kerosene (#1 diesel and #1 oil are acceptable substitutes)
NEVER use fuel such as gasoline, benzene, alcohol, white gas, camp stove fuel, paint thinners, or other oil
compounds in this heater. These are volatile fuels that can cause an explosion or uncontrolled flames.
NEVER store kerosene in direct sunlight or near a source of heat.
NEVER use kerosene that has been stored from one season to the next. Kerosene deteriorates over time.
“OLD KEROSENE” WILL NOT BUR N PROPERLY IN THIS HEATER.
6
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
5. OVERVIEW OF HEATER’S DESIGN
Fuel System : This heater is equipped with an electric
air pump that forces air through the air
line connected to the fuel intake and then
through a nozzle in the burner head.
When the air passes in front of the fuel
intake it causes fuel to rise from the tank
and into the burner nozzle. This fuel and
air mixture is then sprayed into the
combustion chamber in a fine mist.
“Sure Fire Ignition” : The electronic ignitor sends voltage to a specially designed spark plug.
The spark plug ignites the fuel and air mixture described above.
The Air System : The heavy duty motor turns a fan that forces air into and around the combustion chamber.
Here the air is heated and then forced out the front of the heater.
The Safety System :
A. Temperature Limit Control : This heater is equipped with a Temperature Limit Control designed to turn
off the heater should the internal temperature rise to an unsafe level. If this
device activates and turns your heater off it may require service.
MODELS
KFA50DGD/75DGD
KFA125/170DGD
KFA210DGD
Internal Shut-Off Temp.
Plus/Minus 10 Degrees
Ý)ÝC
Ý)ÝC
Ý)ÝC
Reset Temperature
Plus/Minus 10 Degrees
Ý)Ý&
Ý)Ý&
Ý)Ý&
Once the temperature falls below the reset temperature you will be able to start your heater.
B. Electrical System Protection : This heater’s electrical system is protected by a fuse mounted to the PCB
assembly that protects it and other electrical components from damage.
If your heater fails to operate check this fuse first and replace as needed.
FUSE TYPE:
All Models
125 volt / 8 amps
C. Flame-Out Sensor : Utilizes a photocell to monitor the flame in burn chamber during normal operation.
It will cause the heater to shut-off should the burner flame extinguish.
7
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
6. FUELING YOUR HEATER
NEVER FILL THE HEATER FUEL TANK IN THE LIVING SPACE : FILL THE TANK OUTDOORS.
DO NOT OVERFILL YOUR HEATER AND BE SURE HEATER IS LEVELED.
IMPORTANT NOTICE REGARDING FIRST IGNITION OF HEATER :
The first time you light the heater, it should be done outdoors. This allows the oils, etc. used in
manufacturing the heater to burn off outside.
WARNING!! : NEVER REFILL HEATER FUEL TANK WHEN HEATER IS OPERATING OR STILL HOT.
7. OPERATION
A.) VENTILATION
RISK OF INDOOR AIR POLLUTION/USE HEATER ONLY IN WELL VENTILATED AREAS.
Provide a fresh air opening of at least three square feet (2,800 sq. cm) for each 100,000 BTU/Hr.
rating. Provide extra fresh air if more heaters are being used.
Example :
A KFA210DGD heater requires one of the following:
‡DWZRFDUJDUDJHGRRUUDLVHGVL[LQFKHVFP
‡DVLQJOHFDUJDUDJHGRRUUDLVHGQLQHLQFKHVFP
‡WZRWKLUW\LQFKFPZLQGRZVUDLVHGILIWHHQLQFKHVFP
B.) OPERATION
TO START HEATER
1. Fill fuel tank with kerosene or No. 1 fuel oil.
2. Attach fuel cap.
3. Plug power cord of heater into three-prong, grounded extension cord. Extension cord must be at
least six feet long.
Extension Cord Wire Size Requirements
‡6 to 100 feet (1.8 to 30.5 meters) long, use 16 AWG conductor.
‡WRIHHWWRPHWHUVORQJXVH$:*FRQGXFWRU
4. Turn “THERMOSTAT &21752/NQREµWRGHVLUHGVHWWLQJVHWWLQJUDQJHÝ)aÝ)
(KFA75DGD/KFA125/170/210DGD Models Only)
5. Push “BTU control Switch” to desired level “High or LOW” (See Figure 8.)
(KFA125/170/210DGD Models Only)
6. Push Power Switch to “ON” position, Power lndicator Lamp will light and heater will start.
NOTE : Room Temperature display explanations are as follows: (KFA170/210DGD Models only)
‡ :KHQWKHURRPWHPSHUDWXUHLVOHVVɆ, the LED display will show “Lo”
‡ :KHQURRPWHPSLVEHWZHHQɆDQGɆWKHnumber shown on the display is the current
room temperature.
‡ When room temperature is greater thanɆWKH/('GLVSOD\ZLOOVKRZ´+Lµ
If heater does not start, the thermostat setting may be too low, turn “thermostat Control Knob” to
higher position to start heater. If heater still does not start, turn power switch to “OFF” and then to
“ON” position. If heater still does not start, see Troubleshootiong Guide on page15.
NOTE : User can Select to operate the heater on two different BTU levels(High or Low). The BTU level can
be selected before turning the unit on, or while it is in operation by pushing the BTU control switch.
Room Temp. Display
Lamp
Power/Reset
Thermostat
Switch
Control Knob
(75/125DGD MODELS ONLY)
KFA50/75/125DGD Models
BTU Control Switch
Thermostat
Control Knob
BTU Control Switch
Push to “HIGH”
Lamp
Push to “LOW”
Power/Reset
Switch
KFA170/210DGD Models
Fan Guard
Figure 8. Controls for All Models
8
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
NOTICE : The major electrical components of this heater are protected by a safety fuse mounted to the PCBboard.
If your heater fails to start, check this fuse first and replace as necessary. You should also check your
power source to insure that proper voltage and frequency are being supplied to the heater.
TO STOP HEATER
1. Turn switch to “OFF” and unplug power cord.
TO RESTART HEATER
1.Wait 10 seconds after stopping heater.
2. Repeat steps under to start heater.
Cover
PIGGYBACK POWER CORD
Outlet
WARNING : SHOCK HAZARD!
‡ Always cover electric outlet when not in use.
‡ Don’t plug and use a appliance more than 120V/60Hz 5A
current in this outlet.
KFA75DGD/125/170/210DGD Models only
Figure 9. Piggyback Power Cord
8. LONG TERM STORAGE OF YOUR HEATER
FUEL TANK DRAIN
1. Drain fuel tank through fuel cap opening.
(For KFA50DGD/75DGD Models Only)
2. Remove fuel drain bolt from rear bottom side of fuel tank using 3/4” socket or adjustable wrench and drain.
(For KFA125/170/210DGD Models Only. See Figure 10)
3. Using a small amount of kerosene, swirl and rinse the inside of the tank.
NEVER mix water with the kerosene as it will cause rust inside the tank.
Pour the kerosene out making sure that you remove it all.
IMPORTANT : Do not store kerosene over summer months for use during next heating season.
Using old fuel could damage heater.
4. Reinstall fuel cap. Properly dispose of old and dirty fuel. (For KFA50DGD/75DGD Models Only)
5. Reinstall fuel drain bolt to Fuel tank and tighten firmly using 3/4” socket or adjustable wrench.
(For KFA125/170/210DGD Models Only. See Figure 10)
IMPORTANT : Before reinstalling the fuel drain bolt, make sure the seal is on the bolt. If the seal is
not used the bolt cannot be installed correctly and the fuel tank will leak.
Seal
Fuel Drain Bolt
Figure 10. Fuel Drain Bolt
6. Store heater in dry well ventilated area. Make sure storage place is free of dust and corrosive fumes.
7. Store the heater in the original box with the original packing material and keep the USER’S MANUAL
with the heater.
9
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
9. MAINTENANCE
WARNING!! : NEVER SERVICE HEATER WHILE IT IS PLUGGED IN OR
WHILE HOT!
USE ORIGINAL EQUIPMENT REPLACEMENT PARTS. Use of third party or
other alternate components will void warranty and may cause unsafe operating
conditions.
Screw
A.) FUEL TANK
FLUSH EVERY 200 HOURS OF OPERATION OR
AS NEEDED (SEE STORAGE, PAGE 9)
Upper Shell
Air Intake Filter
B.) AIR INTAKE FILTER
WASH AND DRY WITH SOAP AND WATER
EVERY 500 HOURS OF OPERATION OR AS
NEEDED.
- Remove screws along each side of heater using
medium phillips screwdriver.
- Lift upper shell off.
- Remove fan guard.
- Wash or replace air intake filter.
- Reinstall fan guard and upper shell.
Fan Guard
Figure 11. Air Intake Filter Access
C.) AIR OUTPUT FILTER, LINT FILTER
REPLACE EVERY 500 HOURS OF OPERATION
OR ONCE A YEAR.
- Remove upper shell and fan guard (See Air Intake Filter).
- Trun Air pressure gauge counter-clock wise and
remove.
- Remove end filter cover screws using medium
phillips screwdriver.
- Remove end filter cover.
- Replace air output and lint filter.
- Reinstall end filter cover and air pressure gauge.
- Reinstall fan guard and upper shell.
D.) FAN BLADES
Air Output Filter
End Filter Cover
Screw
Lint Filter
Air Intake Filter
Pressure Gauge
Figure 12. Air Outprt Filter Access
CLEAN EVERY SEASON OR AS NEEDED.
- Remove upper shell (See Air Intake Filter).
- Use M6 allen wrench to loosen set screw
which holds fan blade to motor shaft.
- Slip fan blade off motor shaft.
- Clean fan blade using a soft cloth moistened with
kerosene or solvent.
- Dry fan blade thoroughly.
- Reinstall fan blade on motor shaft. Place fan
blade hub flush with end of motor shaft.
- Place set screw on flat of shaft. Tighten set screw
firmly (40-50 inch-pounds/4.5-5.6 N-m).
- Reinstall upper shell.
10
Set Screw
Flush
Motor Shaft
Fan Blade
Motor
Figure 13. Fan Assembly
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
E.) NOZZLE
REMOVE DIRT IN NOZZLE AS NEEDED (SEE PAGE 16).
(For KFA50DGD/75DGD/125/170DGD Models Only)
- Remove upper shell (See page 10).
- Remove fan blade (See page 10).
- Remove fuel and air line hoses from nozzle adaptor.
- Remove ignitor wire from spark plug.
- Remove spark plug from nozzle adaptor using medium
phillips screwdriver.
- Turn nozzle adaptor 1/9 turn(40°) to counter clock wise
and pull toward motor to remove. (See Figure 14)
- Place plastic hex-body into vise and lightlry tighten.
- Carefully remove nozzle from nozzle adaptor using 5/8”
socket wrench.
- Blow compressed air through face of nozzle.
(this will remove any dirt in nozzle)
- Reinstall nozzle into nozzle adaptor until nozzle seats.
Tighten 1/3 turn more using 5/8” socket wrench.
aLQFKSRXQGV
- Reinstall nozzle adaptor to burner head.
- Reinstall spark plug to nozzle adaptor.
- Attach ignitor wire to spark plug.
- Attach fuel and air line hoses to nozzle adaptor.
- Reinstall fan blade and upper shell.
(For KFA210DGD Model Only)
- Remove upper shell (See page 10).
- Remove fan (See page 10).
- Remove fuel and air line hoses from nozzle adaptor.
- Remove ignitor wire from spark plug.
- Remove spark plug from nozzle adaptor using medium
phillips screwdriver.
- Turn nozzle adaptor 1/8 turn (45°) to counter clock wise
and pull toward motor to remove. (See Figure 15)
- Place plastic hex-body into vise and lightly tighten.
- Carefully remove nozzle from nozzle adaptor using 5/8”
socket wrench.
- Blow compressed air through face of nozzle.
(this will remove any dirt in nozzle)
- Reinstall nozzle into nozzle adaptor until nozzle seats
Tighten 1/3 turn more using 5/8” socket wrench
aLQFKSRXQGV
- Reinstall nozzle adaptor to burner bracket
- Reinstall spark plug to nozzle adaptor.
- Attach ignitor wire to spark plug.
- Attach fuel and air line hoses to nozzle adaptor.
- Reinstall fan blade and upper shell.
11
Combustion Chamber
Screw
Ignitor Wire
Spark Plug
Nozzle Adaptor
Burner Head
Fuel Line
Air Line
Nozzle Face
Nozzle Adaptor
Nozzle
Nozzle Adaptor
Figure 14. Nozzle Replacement
Combustion Chamber
Screw
Ignitor Wire
Spark Plug
Nozzle Adaptor
Bracket-Burner
Fuel Line
Air Line
Nozzle Face
Nozzle Adaptor
Nozzle
Nozzle Adaptor
Figure 15. Nozzle Replacement
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
Screw
F.) SPARK PLUG
Spark Plug
GAP
Ignitor Wire
Nozzle Adaptor
Spark Plug
Figure 16. Spark Plug Regap
Nozzle Adaptor
Spark Plug
Screw
GAP
CLEAN AND REGAP EVERY 600 HOURS
OPERATION OR REPLACE AS NEEDED.
(For KFA50DGD/75DGD/125/170DGD Models Only)
- Remove upper shell (See page 10).
- Remove fan (See page 10).
- Remove ignitor wire from spark plug.
- Remove spark plug from nozzle adaptor using medium
phillips screwdriver.
- Clean and regap spark plug electrodes to 3.5mm gap.
(0.138”)
- Reinstall spark plug to nozzle adaptor.
- Attach ignitor wire to spark plug.
- Reinstall fan and upper shell.
(For KFA210DGD Model Only)
- Remove upper shell (See page 10).
- Remove fan (See page 10).
- Remove ignitor wire from nozzle adaptor.
- Remove spark plug from nozzle adaptor using medium
phillips screwdriver.
- Clean and regap spark plug electrodes to 3.5mm gap.
(0.138”)
- ReInstall spark plug to nozzle adaptor.
- Attach ignitor wire to spark plug.
- Reinstall fan and upper shell.
Spark Plug
Ignitor Wire
Figure 17. Spark Plug Regap
G.) PHOTOCELL
CLEAN PHOTOCELL ANNUALLY OR AS
NEEDED.
- Remove upper shell (See page 10).
- Remove fan (See page 10).
- Remove photocell from it’s mounting.
Clean photocell lens with cotton swab.
TO REPLACE:
- Remove side cover screws using medium phillips
screwdriver.
- Disconnect switch wires from power switch and
remove side cover.
- Disconnect wires from circuit board and remove
photocell.
- Install new photocell and connect wires to circuit
board.
- Replace switch wires to power switch and side cover.
- Replace fan and upper shell.
Side Cover
Power
Switch
Screw
Photocell
Wire
Switch
Wires
Bracket
Photocell
Lens
Install Photocell
Incorrect
Correct
Figure 18. Photocell Replacement
12
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
H.) FUEL FILTER
CLEAN OR REPLACE TWICE A HEATING
SEASON OR AS NEED.
- Remove side cover screws using medium phillips
screwdriver.
- Disconnect switch wires from power switch and
remove side cover.
- Pull fuel line off fuel filter neck.
- 7XUQIXHOILOWHUÛWRFRXQWHUFORFNZLVHDQGSXOOWR
remove (KFA50DGD/75DGD Models only).
- 7XUQIXHOILOWHUÛWRFORFNZLVHDQGSXOOWRUHPRYH
(KFA125/170/210DGD Models only).
- Wash fuel filter with clean fuel and replace in tank.
- Attach fuel line to fuel filter neck.
- Replace switch wires to power switch.
- Reinstall side cover.
Fuel Filter
Fuel line
Switch Wires
Screw
Side Cover
Power Switch
I.) PUMP PRESSURE ADJUSTMENT
NOTE: If the pump pressure needs to be adjusted,
make sure the heater is running on the
HIGH BTU setting.
- Push the BTU CONTROL Switch to HIGH.
(See Operation, page 8, KFA125/170/
210DGD Models only)
- Remove Pressure Gauge Plug from End Filter Cover.
Install accessory Pressure Gauge.
(KFA50DGD/75DGD Models only)
- Start heater (See Operation, page 8)
Allow motor to reach full speed
- Adjust pressure (Using a flat blade screwdriver) Turn
relief valve to clockwise to increase pressure. Turn
relief valve to counter clockwise to decreasepressure.
- Stop heater (See Operation, page 8)
MODEL
KFA50DGD
KFA75DGD
KFA125DGD
KFA170DGD
KFA210DGD
Pump Pressure
High BTU level Low BTU level
3.8 psi
N/A
3.8 psi
N/A
5.5 psi
3.5 psi
6.5 psi
4.5 psi
8.5 psi
6.5 psi
NOTE : USE ONLY ORIGINAL EQUIPMENT
REPLACEMENT PARTS.
Use of alternate or third party components will
void any warranty and may cause unsafe
operating condition.
13
Figure 19. Fuel Filter Replacement
Flat blade
Screw driver
End Filter Cover.
Pressure Gauge Plug
Pressure Gauge
Relief Valve
KFA50DGD/75DGD Models Only
Pressure Gauge
BTU Control Switch
Relief Valve
KFA125/170/210DGD Models only
Figure 20. Adjusting Pump Pressure
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
10. REPLACING FUSE
NOTICE : This heater is fuse protected.
If your heater fails to ignite, DO NOT RETURN YOUR HEATER TO THE
STORE.
Please follow the simple instructions below to inspect and change the fuse.
PROCEDURE FOR REPLACING FUSE
WARNING : SHOCK HAZARD
To prevent personal injury, unplug the power cord before replacing fuse.
1. Unplug heater.
2. Remove side cover screws using medium phillips screw driver.
3. Disconnect switch wires from power switch.
4. Remove fuse from fuse holder.(See Figure 21.)
5. Replace fuse with enclosed fuse.
WARNING : FIRE HAZARD
To avoid fire, Do not substitute with a higher or lower current rating.
6. Replace switch wires to power switch.
7. Replace side cover.
Fuse Holder
Fuse
NOTE : Specified fuse rating : AC 125/8A
KFA75DGD/125/170/210DGD Models
Screw
Side Cover
Power Switch
Switch Wire
Fuse
Figure 21. Replacing Fuse
14
Fuse Holder
KFA50DGD
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
11. TROUBLE SHOOTING GUIDE
TROUBLE
Heater ignites but MAIN PCB
assembly shuts heater off after
a short period of time.
(Indicator Lamp is flickering and
room temp. display indicates " E1 ")
Heater will not ignite but
motor runs for a short period
of time.(Indicator Lamp is flickering
and room temp.display
indicates " E1 ")
POSSIBLE CAUSE
1. Wrong pump pressure
2. Dirty Air Output,Air Intake
or Lint Filter.
3. Dirty Fuel Filter.
4. Dirt in Nozzle.
5. Dirty Photocell Lens.
6. Photocell Assembly not
Properly installed.(Not seeing the
flame)
7. Bad electrical connection
between photocell and MAIN
PCB assembly.
8. Defective Photocell.
1. No fuel in tank.
2. Wrong pump pressure.
3. Carbon deposits on spark
plug and/or improper gap.
4. Dirty fuel filter.
5. Dirt in Nozzle.
6. Water in fuel tank.
7. Bad electrical connection
between ignitor and MAIN
PCB assembly.
8. Ignition wire is not attached to
spark plug.
CORRECTIVE ACTION
1. See Pump Pressure Adjustment,
Page 13.
2. See Air Output, Air intake
and Lint Filters, page 10.
3. See Fuel Filter, Page 13.
4. See Nozzle, Page 11.
5. Clean Photocell Lens, Page 12.
6. Make sure photocell boot is
properly seated in bracket,
Page 12.
7. Check electrical components
See wiring diagram, Page 16.
8. Replace Photocell, Page 12.
1. Fill tank with kerosene.
2. See Pump Pressure Adjustment,
Page 13.
3. See Spark Plug, Page 12.
4. See Fuel Filter, Page 13.
5. See Nozzle, Page 11.
6. Flush fuel tank with clean
kerosene, Page 9.
7. Check electrical components
See wiring diagram, Page 16.
8. Attach ignition wire to spark
plug. See Spark Plug, Page 12.
Fan does not turn when heater
is plugged in and power switch
was in the " ON " Position.
(Indicator Lamp is on or flickering)
1. Thermostat setting is too low.
(Indicator Lamp is flickering and
room temp. display indicates "E2")
1. Sensor Failure.
1. Replace sensor.
See Wiring diagram, Page 16.
(Indicator Lamp is flickering and
room temp. display indicates "E3")
1. Thermostat switch failure.
1. Replace switch.
See Wiring diagram, Page 16.
Heater will not turn-on
(Indicator Lamp is off)
1. Temperature limit safety
device is overheated.
1. Turn power switch to "OFF"
and allow to cool (about 10 min.)
2. Check to insure heater cord and
extension cord are plugged in.
Check power supply.
3. Replace safety fuse in PCB board.
4. Check electrical connections
See Wiring Diagram, Page 16.
2. Bad electrical connection
between motor and MAIN
PCB assembly.
2. No electrical power
3. Blown fuse.
4. Bad electrical connection between
temperature limit safety device
and PCB board.
15
1. Turn thermostat control knob
to a higher setting.
2. Check electrical connections,
See Wiring Diagram, Page 16.
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
12. WIRING DIAGRAM
A) WIRING DIAGRAM (KFA50DGD Model)
CONTROL PCB
DISPLAY PCB
BLACK SPARK PLUG
RED
CN3
POWER LAMP
(LED)
IGNITOR
RED
BLACK
2P
CN1
CN1
ORANGE
CN7
BLACK
PUMP
MOTOR WHITE
RED
CAPACITOR
GREEN
15uF/230VAC
PW-W/H
EARTH
PW-BLK
CN2
AC120V
60Hz
BLACK
BLACK
POWER
SWITCH
POWER
PLUG
LIMIT
CONTROL
FUSE
8A/125VAC
BLACK
BLACK
WHITE
BLACK
PHOTO CELL
GREEN
WHITE
EARTH
B) WIRING DIAGRAM (KFA75DGD/125/170/210DGD Models)
CONTROL PCB
BLACK SPARK PLUG
RED
CN4
POWER LAMP
(LED)
RED
IGNITOR
BLACK
ORANGE
CN3
ROOM
SENSOR
RED
BLACK
PUMP
MOTOR WHITE
GREEN
THERMOSTAT
(TEMP. CONTROL)
CAPACITOR
CN2(AC2)/ WHT
CN6
CN5
CN1(AC1)/
EARTH
BLK
POWER
PLUG
AC120V
60Hz
BLACK
POWER
SWITCH
BLACK
BLACK
LIMIT
CONTROL
FUSE
8A/125VAC
GREEN
WHITE
EARTH
16
WHITE
PHOTO
CELL
BLACK
BLACK
MODEL
CAPACITOR
75DGD
15uF/230VAC
125/170/210DGD
20uF/350VAC
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
16.7"(424mm)
13. SPECIFICATIONS
32.0"(813mm)
11.7"(297mm)
KFA50DGD/75DGD Models
H
125DGD
170DGD
210DGD
D 41.9"(1,063 mm) 47.4"(1,205 mm)
W 21.5"(547 mm) 23.1"(587 mm)
D
H 32.4"(824 mm)
W
33.5"(850 mm)
KFA125/170/210DGD Models
KFA50DGD
KFA75DGD
KFA125DGD
KFA170DGD
KFA210DGD
HIGH
50,000
75,000
125,000
170,000
210,000
LOW
N/A
N/A
100,000
135,000
170,000
HIGH
0.38(1.44)
0.57(2.16)
0.95(3.60)
1.30(4.92)
1.60(6.06)
LOW
N/A
N/A
0.76(2.90)
1.0(3.79)
1.30(4.92)
5.0(18.9)
5.0(18.9)
10.0(37.9)
13.0(49.2)
13.0(49.2)
HIGH
3.8(0.27)
3.8(0.27)
5.5(0.39)
6.5(0.46)
8.5(0.60)
LOW
N/A
N/A
3.5(0.25)
4.5(0.32)
6.5(0.46)
Volt/Hz
120Vac/60hz
120Vac/60hz
120Vac/60hz
120Vac/60hz
120Vac/60hz
Amps.
1.6
1.6
2.5
3.2
3.7
Phase
1
1
1
1
1
MODEL
BTU/Hr.
Fuel Consumption
- Gal./Hr( ./Hr)
Fuel Tank Capacity - Gal.( )
Pump Pressure PSI(kgf/㎠)
Size(D×W×H), Inch(㎜)
Weight Lbs.(㎏)
32.0×11.7×16.7
(813×297×424)
26.9(12.2)
32.0×11.7×16.7 41.9×21.5×32.4 47.4×23.1×33.5 47.4×23.1×33.5
(813×297×424) (1,063×547×824) (1,205×587×850) (1,205×587×850)
26.9(12.2)
17
54.5(24.7)
60.2(27.3)
62.4(28.3)
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
14. EXPLODED PARTS DRAWING (KFA50DGD/75DGD Models Only)
NOTE : SPECIFY MODEL NUMBER AND PART NUMBER WHEN ORDERING PARTS.
41
38
37
22-3
22-5
22-1
40
22-8
22-7
22-2
22-4
22-6
18
39
20
21
27
26
22 23
25
19
17
16
10
12
13
24
15
14
28
11
29
4
35
31
30
1
9
36
3
5
6
34
25-2
8
32
25-5
7
25-6
25-7
25-9
25-8
25-11
25-15
2
33
25-1
25-3
25-16
25-4
25-17
25-18
25-21
25-10
25-12
25-13
25-14
18
25-20
25-19
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
15. PARTS LIST (KFA50DGD/75DGD Models Only)
KEY NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
22-1
22-2
22-3
22-4
22-5
22-6
22-7
22-8
22
24
25
25-1
25-2
25-3
25-4
25-5
25-6
25-7
25-8
25-9
25-10
25-11
25-12
Fuel Tank Assmebly
Fuel Drain-Bolt
Fuel Gauge
Fuel Filter Assmbly
Fuel Cap
Cord Bushing
Power Cord
Button Support
Display P.C.B Assembly
Shell Lower
Flange Screw
Clip Nut
Bushing-Grommet(S)
Bushing-Grommet(L)
Air-Line
Temperature Limit Assembly
Flange-Screw
Chamber Assembly
Bracket Photocell
Screw-BH1
Photocell Assembly
Burner Head Assembly
Burner Head
Nozzle
Washer-Nozzle Seal
Spring-Nozzle Seal
O-Ring
Nozzle Adaptor
Spark Plug
Bolt-Flange
Flange Screw
Fuel Line
Motor and Pump Assembly
Motor
Capacitor
Motor Support
Nut-Hex
Holder Capacitor
Pump Body
Bolt-BH Special
Rotor
Blade
Insert
End Pump Cover
Elbow
PART NO.
KFA50DGD
2151-0026-00
2156-0047-00
2155-0005-00
2151-0041-00
3712-0013-00
3980-0031-00
3713-0048-00
215A-0013-00
3111-0343-05
4319-0015-00
3131-0182-00
3231-0120-00
3231-0121-00
3341-0021-00
2153-0022-00
4319-0015-00
2152-0115-00
3131-0159-00
4311-0068-00
*SP-KFA1007
2152-0120-00
3531-0026-00
*SP-KFA1026
4349-0016-00
3431-0010-00
3311-0002-00
3231-0178-00
*SP-KFA1008
4329-0079-00
4319-0015-00
3341-0024-00
2154-0078-00
3970-0210-00
3820-0257-00
3121-0481-00
4331-0022-00
3541-0022-00
4321-0198-00
See SP-KFA10001
See SP-KFA10001
See SP-KFA10001
3531-0027-00
3231-0181-00
19
KFA75DGD
2151-0027-00
2156-0049-00
2155-0005-00
2151-0041-00
3712-0013-00
3980-0177-00
3111-0343-05
4319-0015-00
3131-0182-00
3231-0120-00
3231-0121-00
3341-0021-00
2153-0022-00
4319-0015-00
2152-0116-00
3131-0159-00
4311-0068-00
*SP-KFA1007
2152-0121-00
3531-0026-00
*SP-KFA1027
4349-0016-00
3431-0010-00
3311-0002-00
3231-0178-00
*SP-KFA1008
4329-0079-00
4319-0015-00
3341-0024-00
2154-0078-00
3970-0210-00
3820-0257-00
3121-0481-00
4331-0022-00
3541-0022-00
4321-0198-00
See SP-KFA10001
See SP-KFA10001
See SP-KFA10001
3531-0027-00
3231-0181-00
Quantity
1
1
1
1
1
1
1
2
1
1
4
8
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
3
1
1
1
1
1
2
1
1
2
1
4
1
1
1
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
15. PARTS LIST (KFA50DGD/75DGD Models Only)
KEY NO.
25-13
25-14
25-15
25-16
25-17
25-18
25-19
25-20
25-21
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
KEY NO.
1
2
3
DESCRIPTION
Lint Filter
Bolt Flange
Output Filter
End Filter Cover
Ball
Spring
Adjusting Screw
Bolt Flange
Intake Filter
Fan Assembly
Bolt Headless Hex Socket
Plug
Main P.C.B Assembly
Screw-TH2S
Ignitor
Side Cover-Right
Power Switch
Flange Screw
Side Cover-Left
Flange Screw
Shell Upper
Clip Nut
Fan Guard
Flange Screw
Front Guard
DESCRIPTION
Rotor kit
Filter kit
Plug/Pump adjuster kit
PART NO.
KFA50DGD
2
See SP-KFA1005
4329-0016-00
See SP-KFA10052
3221-0029-00
See SP-KFA10063
See SP-KFA10063
See SP-KFA10063
4329-0016-00
See SP-KFA10052
2154-0009-00
4323-0004-00
3231-0054-00
215A-0048-00
4312-0046-00
39E0-0071-00
3121-0496-04
39A0-0191-00
4319-0015-00
3121-0190-00
4319-0015-00
3111-0347-05
3131-0182-00
3221-0050-00
4319-0015-00
3561-0066-00
Quantity
KFA75DGD
2
See SP-KFA1005
4329-0016-00
See SP-KFA10052
3221-0029-00
See SP-KFA10063
See SP-KFA10063
See SP-KFA10063
4329-0016-00
See SP-KFA10052
2154-0009-00
4323-0004-00
3231-0054-00
215A-0073-00
4312-0046-00
39E0-0071-00
3121-0497-05
39A0-0191-00
4319-0015-00
3121-0350-00
4319-0015-00
3111-0347-05
3131-0182-00
3221-0050-00
4319-0015-00
3561-0066-00
PART NO.
KFA50DGD
KFA75DGD
SP-KFA1000
SP-KFA1005
SP-KFA1006
SP-KFA1000
SP-KFA1005
SP-KFA1006
FOR TECHNICAL ASSISTANCE SEE YOUR LOCAL RETAILER OR
CONTACT US AT:
Phone : 1-877-447-4768
20
1
6
1
1
1
1
1
4
1
1
1
1
1
2
1
1
1
4
1
4
1
2
1
8
1
Quantity
1
1
1
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
14. EXPLODED PARTS DRAWING (KFA125/170DGD Models Only)
NOTE : SPECIFY MODEL NUMBER AND PART NUMBER WHEN ORDERING PARTS.
20-3
20-5
37
20-8
20-7
20-2
20-1
20-4
39
20-6
16
18
19
38
25
24
20 21
23
17
15
14
8
10
11
22
13
12
26
9
28
4
27
35
30
1
29
36
3
5
6
34
23-2
7
33
31
23-5
2
23-6
23-7
23-9
23-8
23-11
23-15
32
23-1
23-3
23-16
23-17
23-18
23-4
23-10
23-21
23-12
23-13
23-14
23-20
23-19
21
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
15. PARTS LIST (KFA125/170DGD Models Only)
KEY NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
20-1
20-2
20-3
20-4
20-5
20-6
20-7
20-8
21
22
23
23-1
23-2
23-3
23-4
23-5
23-6
23-7
23-8
23-9
23-10
23-11
23-12
23-13
23-14
PART NO.
DESCRIPTION
KFA125DGD
KFA170DGD
Fuel Tank Assmebly
Fuel Drain-Bolt
Fuel Gauge
Fuel Filter Assmbly
Fuel Cap
Cord Bushing
Power Cord
Shell Lower
Flange Screw
Clip Nut
Bushing-Grommet(S)
Bushing-Grommet(L)
Air-Line
Temperature Limit Assembly
Flange-Screw
Chamber Assembly
Bracket Photocell
Screw-BH1
Photocell Assembly
Burner Head Assembly
Burner Head
Nozzle
Washer-Nozzle Seal
Spring-Nozzle Seal
O-Ring
Nozzle Adaptor
Spark Plug
Bolt-Flange
Flange Screw
Fuel Line
Motor and Pump Assembly
Motor
Capacitor
Motor Support
Nut-Hex
Holder Capacitor
Pump Body
Bolt-BH Special
Rotor
Blade
Insert
End Pump Cover
Elbow
Lint Filter
Bolt Flange
2151-0028-00
4329-0072-00
2156-0050-00
2155-0001-00
2151-0041-00
3712-0013-00
3980-0177-00
3111-0344-05
4319-0015-00
3131-0182-00
3231-0120-00
3231-0121-00
3341-0002-00
2153-0023-00
4319-0015-00
2152-0117-00
3131-0159-00
4311-0068-00
*SP-KFA1007
2152-0122-00
3531-0025-00
*SP-KFA1003
4349-0016-00
3431-0010-00
3311-0002-00
3231-0179-00
*SP-KFA1009
4329-0079-00
4319-0015-00
3341-0025-00
2154-0075-00
3970-0211-00
3820-0258-00
3121-0482-00
4331-0022-00
3231-0182-00
3541-0022-00
4321-0198-00
See SP-KFA10001
See SP-KFA10001
See SP-KFA10001
3531-0027-00
3231-0181-00
See SP-KFA10052
4329-0016-00
2151-0029-00
4329-0072-00
2156-0051-00
2155-0001-00
2151-0041-00
3712-0013-00
3980-0177-00
3111-0345-05
4319-0015-00
3131-0182-00
3231-0120-00
3231-0121-00
3341-0022-00
2153-0023-00
4319-0015-00
2152-0118-00
3131-0159-00
4311-0068-00
*SP-KFA1007
2152-0123-00
3531-0024-00
*SP-KFA1004
4349-0016-00
3431-0010-00
3311-0002-00
3231-0179-00
*SP-KFA1009
4329-0079-00
4319-0015-00
3341-0025-00
2154-0076-00
3970-0212-00
3820-0258-00
3121-0482-00
4331-0022-00
3231-0182-00
3541-0022-00
4321-0198-00
See SP-KFA10001
See SP-KFA10001
See SP-KFA10001
3531-0027-00
3231-0181-00
See SP-KFA10052
4329-0016-00
22
Quantity
1
1
1
1
1
1
1
1
4
8
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
3
1
1
1
1
1
2
1
1
2
1
4
1
1
1
1
6
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
15. PARTS LIST (KFA125/170DGD Models Only)
KEY NO.
23-15
23-16
23-17
23-18
23-19
23-20
23-21
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
KEY NO.
1
2
3
DESCRIPTION
Output Filter
End Filter Cover
Ball
Spring
Adjusting Screw
Bolt Flange
Intake Filter
Fan Assembly
Bolt Headless Hex Socket
Pressure Gauge
BTU Control Switch
Main P.C.B Assembly
Screw-TH2S
Ignitor
Side Cover-Right
Power Switch
Window Display
Flange Screw
Side Cover-Left
Flange Screw
Shell Upper
Fan Guard
Flange Screw
PART NO.
KFA125DGD
Quantity
KFA170DGD
2
2
See SP-KFA1005
3221-0076-00
See SP-KFA10103
See SP-KFA10103
See SP-KFA10103
4329-0016-00
See SP-KFA10052
2154-0007-00
4323-0004-00
3740-0049-00
2154-0070-00
215A-0074-00
4312-0046-00
39E0-0071-00
3121-0499-05
39A0-0191-00
3231-0113-00
4319-0015-00
3121-0354-00
4319-0015-00
3111-0349-05
3221-0075-00
4319-0015-00
See SP-KFA1005
3221-0076-00
See SP-KFA10103
See SP-KFA10103
See SP-KFA10103
4329-0016-00
See SP-KFA10052
2154-0004-00
4323-0004-00
3740-0049-00
2154-0070-00
215A-0073-00
4312-0046-00
39E0-0071-00
3121-0510-00
39A0-0191-00
4319-0015-00
3121-0352-00
4319-0015-00
3111-0348-05
3221-0075-00
4319-0015-00
PART NO.
DESCRIPTION
KFA125DGD
KFA170DGD
Rotor kit
Filter kit
Plug/Pump adjuster kit
SP-KFA1000
SP-KFA1005
SP-KFA1010
SP-KFA1000
SP-KFA1005
SP-KFA1010
FOR TECHNICAL ASSISTANCE SEE YOUR LOCAL RETAILER OR
CONTACT US AT:
Phone : 1-877-447-4768
23
1
1
2
2
2
4
1
1
1
1
1
1
2
1
1
1
1
4
1
4
1
1
8
Quantity
1
1
2
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
14. EXPLODED PARTS DRAWING (KFA210DGD Model Only)
NOTE : SPECIFY MODEL NUMBER AND PART NUMBER WHEN ORDERING PARTS.
20-8
37
20-3
20-7
20-5
20-1
40
20-2
20-4
20-6
16
18
19
20
39
25
24
21
38
23
17
15
14
8
10
11
22
13
12
26
9
28
4
27
35
30
1
29
36
3
5
23-2
6
34
23-5
7
33
31
23-6
23-7
23-9
23-8
23-11
23-15
2
32
23-1
23-3
23-4
23-16
23-17
23-18
23-10
23-21
23-12
23-13
23-14
23-20
23-19
24
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
15. PARTS LIST (KFA210DGD Model Only)
KEY NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
20-1
20-2
20-3
20-4
20-5
20-6
20-7
20-8
21
22
23
23-1
23-2
23-3
23-4
23-5
23-6
23-7
23-8
23-9
23-10
23-11
23-12
23-13
23-14
Fuel Tank Assmebly
Fuel Drain-Bolt
Fuel Gauge
Fuel Filter Assmbly
Fuel Cap
Cord Bushing
Power Cord
Shell Lower
Flange Screw
Clip Nut
Bushing-Grommet(S)
Bushing-Grommet(L)
Air-Line
Temperature Limit Assembly
Flange-Screw
Chamber Assembly
Bracket Photocell
Screw-BH1
Photocell Assembly
Burner Head Assembly
Bracket Burner
Nozzle
Washer-Nozzle Seal
Spring-Nozzle Seal
O-Ring
Nozzle Adaptor
Spark Plug
Bolt-Flange
Flange Screw
Fuel Line
Motor and Pump Assembly
Motor
Capacitor
Supportor Motor
Nut-Hex
Holder Capacitor
Pump Body
Bolt-BH Special
Rotor
Blade
Insert
End Pump Cover
Elbow
Lint Filter
Bolt Flange
PART NO.
KFA210DGD
2151-0029-00
4329-0072-00
2156-0052-00
2155-0001-00
2151-0041-00
3712-0013-00
3980-0177-00
3111-0346-05
4319-0015-00
3131-0182-00
3231-0120-00
3231-0121-00
3341-0023-00
2153-0005-00
4319-0015-00
2152-0119-00
3131-0159-00
4311-0068-00
*SP-KFA1007
2152-0124-00
3121-0477-00
*SP-KFA1011
4349-0016-00
3431-0010-00
3311-0002-00
3231-0180-00
*SP-KFA1021
4329-0079-00
4319-0015-00
3341-0019-00
2154-0077-00
3970-0213-00
3820-0258-00
3121-0482-00
4331-0022-00
3231-0182-00
3541-0050-00
4321-0198-00
See SP-KFA10221
See SP-KFA10221
See SP-KFA10221
3531-0027-00
3231-0181-00
See SP-KFA10052
4329-0016-00
25
Quantity
1
1
1
1
1
1
1
1
4
8
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
2
1
1
2
1
4
1
1
1
1
6
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
15. PARTS LIST (KFA210DGD Model Only)
KEY NO.
23-15
23-16
23-17
23-18
23-19
23-20
23-21
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
KEY NO.
1
2
3
PART NO.
KFA210DGD
DESCRIPTION
Quantity
2
1
1
2
2
2
4
1
1
1
1
1
1
2
1
1
1
1
4
1
4
1
1
3
8
See SP-KFA1005
3221-0076-00
See SP-KFA10103
See SP-KFA10103
See SP-KFA10103
4329-0016-00
See SP-KFA10052
2154-0007-00
4323-0004-00
3740-0049-00
2154-0070-00
215A-0074-00
4312-0046-00
39E0-0071-00
3121-0499-10
39A0-0191-00
3231-0113-00
4319-0015-00
3121-0354-00
.
4319-0015-00
3111-0350-05
3561-0078-00
3351-0010-00
4319-0015-00
Output Filter
End Filter Cover
Ball
Spring
Adjusting Screw
Bolt Flange
Intake Filter
Fan Assembly
Bolt Headless Hex Socket
Pressure Gauge
BTU Control Switch
Main P.C.B Assembly
Screw-TH2S
Ignitor
Side Cover-Right
Power Switch
Window Display
Flange Screw
Side Cover-Left
Flange Screw
Shell Upper
Fan Guard
Bushing Fan Guard
Flange Screw
DESCRIPTION
PART NO.
KFA210DGD
Quantity
Rotor kit
Filter kit
Plug/Pump adjuster kit
SP-KFA1022
SP-KFA1005
SP-KFA1010
1
1
2
FOR TECHNICAL ASSISTANCE SEE YOUR LOCAL RETAILER OR
CONTACT US AT:
Phone : 1-877-447-4768
26
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
15. PARTS LIST (WHEELS AND HANDLE)
1) KFA50DGD/75DGD MODELS
KEY NO. DESCRIPTION
1
2
Handle
Hardware Kit
2
1
PART NO.
KFA50DGD
3231-0073-00
HW-KFA1001
Quantity
KFA75DGD
3231-0073-00
HW-KFA1001
1
1
2) KFA125/170/210DGD MODELS
KEY NO.
DESCRIPTION
1
2
3
4
5
6
7
7-1
7-2
7-3
7-4
7-5
7-6
Front Handle
Rear Handle
Wheel Support Frame
Wheel
Threaded Axle
Cord Wrap
Hardware Kit
Screw
Flange Screw
Cap Nut S
Nut
Bushing
Cap Nut L
PART NO.
KFA125DGD
KFA170/210DGD
3551-0022-00
3551-0023-00
3551-0097-00
3551-0096-00
3551-0084-00
3551-0082-00
3720-0017-00
3720-0017-00
3551-0089-00
3551-0088-00
3221-0042-00
3221-0042-00
HW-KFA1016
HW-KFA1016
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
INCLUDED IN HARDWARE KIT
1
7-1
7-3
2
6
7-2
3
7-4
5
7-5
4
7-6
27
Quantity
1
1
1
2
1
2
1
8
4
4
8
2
2
GHP Group, Inc.
6440 W Howard St
Niles, IL 60714-3302
Tel: (877) 447-4768
www.ghpgroupinc.com
GHP Group, Inc.
6440 W Howard St
Niles, IL 60714-3302

advertisement

Related manuals

advertisement