EverFocus PARAGON EDR16, EDR8 Digital Video Recorder Instruction Manual

EverFocus PARAGON EDR16, EDR8 Digital Video Recorder Instruction Manual

Below you will find brief information for PARAGON EDR16, PARAGON EDR8. The PARAGON series DVRs are engineered for express operations, this means that setup, copy, search, and playback recordings can be done in seconds with a simple “point and click” on the command icons. These DVRs are based on MPEG-4 compression technology resulting in enhanced recording capacity and improved network image transmission speed with high image quality. The PARAGON Series DVR comes with multiple control inputs including mouse control, front panel control, IR remote control and EverFocus keyboard (EKB500) control.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

PARAGON EDR16, PARAGON EDR8 Instruction Manual | Manualzz
Instruction Manual
PARAGON Series DVR
EVERFOCUS ELECTRONICS CORPORATION
PARAGON Series DVR
Instruction Manual
 2009 EverFocus Electronics Corp
www.everfocus.com
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by
any means without written permission of the Everfocus Electronics Corporation.
Release Date: June. 2009
QuickTime is a registered trademark of the Apple Computer, Inc.
Windows is a registered trademark of the Microsoft Corporation.
Linksys is a registered trademark of the Linksys Corporation.
D-Link is a registered trademark of the D-Link Corporation.
DynDNS is a registered trademark of the DynDNS.org Corporation.
Other product and company names mentioned herein may be the trademarks of their respective owners.
Safety Precautions
• To avoid any damage, please consider the following safety warnings:
• Never place the recorder near to heaters, furnaces, other heat sources or under direct solar irradiation.
• Operate the device only in locations providing the tolerable operating temperature range
0°C~40°C/32°F ~ +104°F.
• Make sure that the device‘s ventilation slots are not covered or sheeted.
• For cleaning, make sure the device is plugged off and only use a damp cloth without acid detergent.
• Install the device only in dry and dustproof surroundings. Protect the device against any liquid‘s
penetration.
• Avoid the penetration of any artifacts, e.g. through ventilation slots.
• Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or
covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.
Handle the appliance with care. Do not strike or shake, as this may damage the appliance.
• Do not operate appliance with other than specified power supplies. The input power source of the power
supply is 100 ~ 240 VAC.
• Avoid any affection of the device through vibrations or mechanical shock at the recorder‘s installation
location.
• Avoid to power off DVR during playback or recording operation.
ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in
this case, the user may be urged to take adequate measures.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures :
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the users’ authority to operate this equipment.
ii
WEEE
This Product is RoHS compliant.
The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve his products.
Therefore, all specifications are subject to change without prior notice. Misprints reserved.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.
iii
TABLE OF CONTENTS
1
PRODUCT OVERVIEW ..................................................................................................... 1
1.1
1.2
1.3
1.4
1.5
2
FEATURES ....................................................................................................................... 1
PACKAGE CONTENTS................................................................................................... 2
SPECIFICATIONS ........................................................................................................... 3
FRONT PANEL ................................................................................................................ 6
REAR PANEL................................................................................................................... 9
INSTALLATION................................................................................................................ 11
2.1
2.2
2.3
VIDEO INPUTS/OUTPUTS INSTALLATION ............................................................. 11
AUDIO INSTALLATION .............................................................................................. 13
ALARM / CONTROL CONTACTS INSTALLATION ................................................. 14
2.3.1
2.3.2
2.3.3
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.5
2.6
2.7
NETWORK CONNECTION .......................................................................................... 19
2.7.1
2.7.2
2.8
3
Alarm Input Contacts ............................................................................................................................14
Control Input Contact ...........................................................................................................................14
Alarm Output Relay...............................................................................................................................15
RS-485 KEYBOARD / PTZ INSTALLATION ......................................................................... 15
General RS-485 bus installation ...........................................................................................................16
RS-485 socket pin assignment ...............................................................................................................17
EKB-500 connection with network patch cable.....................................................................................18
EKB-500 connection to several DVRs...................................................................................................18
Speed Dome Installation .......................................................................................................................18
RS-232 CONNECTION ....................................................................................................... 18
USB-MOUSE INSTALLATION ............................................................................................ 19
Direct PC Connection through Crossover Network Cable ...................................................................19
Network Connection through Patch Cable............................................................................................20
FINAL INSTALL PROCESS.......................................................................................... 20
MOUSE AND FRONT PANEL OPERATION ............................................................... 21
3.1
GENERAL USB MOUSE OPERATION ....................................................................... 21
3.1.1
3.1.2
3.1.3
3.1.4
3.2
GENERAL FRONT PANEL OPERATION ................................................................... 24
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
4
How to select a channel / Enable audio ................................................................................................21
OSD Root Menu ....................................................................................................................................21
Operation in Configuration Menu.........................................................................................................21
Component Options...............................................................................................................................22
How to select a channel / Enable audio ................................................................................................24
OSD Root Menu ....................................................................................................................................24
Front Panel Key Review........................................................................................................................24
Operation in Configuration Menu.........................................................................................................24
Component Options...............................................................................................................................25
GENERAL DVR OPERATIONS...................................................................................... 27
4.1
RECORD ......................................................................................................................... 27
iv
4.2
4.3
4.4
4.5
4.6
LOGIN............................................................................................................................. 27
SELECT CAMERA OPERATION................................................................................. 28
CHANGE AUDIO OUTPUT OPERATION .................................................................. 28
PLAYBACK.................................................................................................................... 28
PTZ .................................................................................................................................. 30
4.6.1
4.6.2
4.7
General PTZ control .............................................................................................................................30
Express control PTZ ..............................................................................................................................31
LAYOUT......................................................................................................................... 33
4.7.1
Bring to full screen mode ......................................................................................................................33
4.8 CHANNEL SWITCHING............................................................................................... 34
4.9 DISPLAY ........................................................................................................................ 34
4.10
SEQUENCE.................................................................................................................. 35
4.11
MONITOR.................................................................................................................... 35
4.12
ZOOM........................................................................................................................... 36
4.13
SEARCH....................................................................................................................... 37
4.13.1
4.13.2
4.13.3
4.14
4.15
5
Time Search...........................................................................................................................................37
Event Search..........................................................................................................................................38
Motion Search .......................................................................................................................................39
COPY............................................................................................................................ 41
LOGOUT ...................................................................................................................... 42
DVR CONFIGURATION .................................................................................................. 43
5.1
5.2
5.3
5.3.1
5.3.2
5.3.3
5.3.4
5.4
5.4.1
5.4.2
5.4.3
5.5
5.5.1
5.5.2
5.6
5.6.1
5.6.2
5.6.3
5.7
5.7.1
5.7.2
5.7.3
5.7.4
5.8
5.8.1
5.8.2
CONFIGURATION MENU............................................................................................ 43
EXPRESS ........................................................................................................................ 43
CAMERA SETTING ...................................................................................................... 45
Basic Setting..........................................................................................................................................46
Video Adjust ..........................................................................................................................................48
Motion ...................................................................................................................................................49
Video Loss .............................................................................................................................................52
RECORD & PLAY SETTING........................................................................................ 53
Record ...................................................................................................................................................53
Built-in Cal............................................................................................................................................54
Play .......................................................................................................................................................55
ALARM & EVENT SETTING....................................................................................... 56
Alarm.....................................................................................................................................................56
Event......................................................................................................................................................59
SCHEDULE SETTING................................................................................................... 68
Express Setup ........................................................................................................................................68
Holidays ................................................................................................................................................69
Schedule ................................................................................................................................................70
NETWORK SETTING.................................................................................................... 75
LAN .......................................................................................................................................................75
EMAIL ...................................................................................................................................................76
DDNS ....................................................................................................................................................77
Alarm Server .........................................................................................................................................79
DISPLAY SETTING....................................................................................................... 80
Monitor OSD .........................................................................................................................................80
Main M/T SEQ ......................................................................................................................................81
v
5.8.3
5.9
Call M/T SEQ ........................................................................................................................................81
DISK SETTING .............................................................................................................. 82
5.9.1
5.9.2
Disk .......................................................................................................................................................82
Lock/Format ..........................................................................................................................................83
5.10
SYSTEM SETTING ..................................................................................................... 84
5.10.1
5.10.2
5.10.3
5.10.4
5.10.5
5.11
INFORMATION SETTING......................................................................................... 90
5.11.1
5.11.2
6
Date/Time ..............................................................................................................................................84
Daylight Saving .....................................................................................................................................85
User .......................................................................................................................................................86
I/O Control ............................................................................................................................................88
Misc. ......................................................................................................................................................89
System....................................................................................................................................................90
Log.........................................................................................................................................................91
NETWORKING OVERVIEW .......................................................................................... 93
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
7
INTRODUCTION TO TCP/IP ............................................................................................... 93
SUBNET MASKS ................................................................................................................ 93
GATEWAY ADDRESS ......................................................................................................... 93
VIRTUAL PORTS ................................................................................................................ 94
PRE-INSTALLATION .......................................................................................................... 94
WHAT IS YOUR NETWORK SETUP?.................................................................................... 95
SIMPLE ONE TO ONE CONNECTION ................................................................................... 96
DIRECT HIGH SPEED MODEM CONNECTION ................................................................... 101
ROUTER OR LAN CONNECTION ...................................................................................... 103
REMOTE OPERATION FROM BROWSER............................................................... 106
7.1
7.2
CONNECTING TO PARAGON................................................................................... 106
BROWSER SECURITY SETTING .................................................................................. 107
7.2.1
7.2.2
7.3
7.4
7.5
Installing ActiveX controls ..................................................................................................................107
Enabling ActiveX Controls..................................................................................................................109
REMOTE LIVE VIEW ................................................................................................. 112
REMOTE PTZ CONTROL........................................................................................... 113
REMOTE PLAYBACK ................................................................................................ 115
8
EVERFOCUS DDNS SETUP .......................................................................................... 116
9
LINKSYS & D-LINK PORT FORWARDING ............................................................. 117
9.1
9.2
10
LINKSYS PORT FORWARDING ............................................................................... 117
D-LINK PORT FORWARDING .................................................................................. 119
TROUBLESHOOTING ................................................................................................ 122
APPENDIX A: TIMING OF ALARM MODES.................................................................... 123
APPENDIX B: CHANGING RULE FOR EXPRESS SETUP ............................................. 126
vi
Chapter
1
1 PRODUCT OVERVIEW
The latest EverFocus digital video recorder generation is based on MPEG-4 compression technology,
resulting in enhanced recording capacity and improved network image transmission speed with high image
quality. Comprehensive features and extended event recording settings enable the almost universal
application of this DVR series. The Paragon Series DVR comes with multiple control inputs. These inputs
include mouse control, front panel control, IR remote control and EverFocus keyboard (EKB500) control.
Mouse control is supported with the simple Graphical User Interface (GUI), offering experienced PC users
the similarity of interactive command of a computer-controlled device. With the GUI, users can command
specific actions on the Paragon Series DVR through graphical icons and visual indicators. Simply point,
click and drag the playback bar on the screen to playback our recordings in any time slot. All GUI functions
can be operated via front panel, IR remote and keyboard as well. Hop on the Express Lane! The Paragon
series DVR is engineered for express operations. Setup, copy, search and playback recordings in seconds
with a simple “point and click” on the command icons.
1.1 FEATURES
•
Pentaplex Operation (Simultaneous live, recording, playback, archiving and remote viewing)
•
User friendly GUI with graphical icons and visual indicators
•
Multiple Control Inputs: mouse/front panel/remote control
•
Free EverFocus DDNS Service
•
Built-in DVR calculator for fast recording estimation
•
Express Setup: Located in menu option for quick & easy installation
•
Express Copy: Record video instantly while playing back (USB)
•
Express Playback: Simply point, click and drag the playback bar to view
•
previous recordings
•
Express Search: Use intuitive playback bar with a simple drag &
•
drop operation
•
Remote configuration support from built-in web interface
•
Gigabit Ethernet interface for remote network viewing and controlling
•
Real-time live display for all cameras
1
•
On-screen PTZ control via mouse or front panel
•
Support EKB500 keyboard control
•
Audio recording capabilities*
•
2 Hot Swappable HDD or 4 internal HDD
•
Built-in DVD burner*
•
Support eSATA
•
2 USB 2.0 ports (located on front panel) for video archive and mouse usage
•
Multi-language support
•
Simultaneous VGA, composite and S-Video output
•
Watermark capabilities to identify intentional modifications of recorded data
•
Rack mountable
*Feature not available for all models
1.2 PACKAGE CONTENTS
-HDD fixing bracket x 4 (Internal HDD model)
-HDD tray x 2 (External HDD model)
-DVR fixing bracket x 2
-Remote controller x 1
-Battery x 2
-Shockproof rubber x 16(Internal HDD model)
-Screws x 16(Internal HDD model)
-Expanding screws x 16(Internal HDD model)
-SATA cable(Internal HDD model x4, Removable HDD model x 2)
-Hard Disc Tray x 2(Removable HDD model)
-Power cord x 1
-Mouse x 1
-DVR x 1
-User manual x 1
2
1.3 SPECIFICATIONS
Video Format
NTSC / PAL (auto detected by system)
Operating System
Embedded Linux
Video Input
EDR16: 16 x 1 Vpp FBAS, BNC, 75 Ohm
EDR8: 8 x 1 Vpp FBAS, BNC, 75 Ohm
Video Loop
EDR16: 16 x 1 Vpp FBAS, BNC, 75 Ohm
EDR8: 8 x 1 Vpp FBAS, BNC, 75 Ohm
Video Output
Main monitor: 1 Vpp FBAS, BNC at 75 Ohm
1 x VGA ( res. 800x600@60 Hz), S-Video
Video Compression
MPEG-4
Video Display
Full screen, Picture In Picture (Live only), 4-channel, 9-channel, 10channel, 13-channel, 16-channel
Recording Resolution
NTSC: 704 x 480, 704 x 240 or 352 x 240
PAL: 704 x 576, 704 x 288 or 352 x 288
Audio*
Input:
EDR16: 16 Line In, 1 Vpp @ 20 KOhm (RCA)
EDR8: 8 Line In, 1 Vpp @ 20 KOhm (RCA)
Output:
1 x Line out 1 Vpp @ 20 KOhm (RCA)
(* audio models only)
Alarm Input
EDR16: 16 Inputs
EDRR8: 8 Inputs
Alarm Output
4 Alarm Outputs (N.C/COM/N.O)
Hard Disk
4 x 3.5” SATA hard disk(Internal HDD model)
2 x 3.5” SATA hard disk(Removable HDD model)
Recording Rate
NTSC
352 x 240: 480 IPS
704 x 240: 240 IPS
704 x 480: 120 IPS
PAL
352 x 288: 400 IPS
704 x 288: 200 IPS
704 x 576: 100 IPS
3
Recording Modes
Continuous, schedule, or event recording
Playback Rate
NTSC
352 x 240: 480 IPS
704 x 240: 240 IPS
704 x 480: 120 IPS
Playback Search Function
By time / date; by event (alarm / motion); Smart Motion Grid Search
Motion Detection
Adjustable by channel , 22x16 sensor fields each with 10 levels
sensitivity
Video Loss Detection
Yes
Event Log
Maximum 500000 events
Event Alarm
Fan failure, hard disk failure, hard disk temperature over, hard disk full,
HD off, power loss, record stop, network loss
Setup
Graphical On-Screen-Display
Operation
Via front panel, USB optical mouse, IR remote control, or
RS-485 operation from EKB500
Real-time Clock
Internal with optional network synchronization (NTP server)
Watchdog Function
Yes
Network
10/100/1000Mbps, RJ45 connection
File Export
USB 2.0 interface
Built-in DVD+RW (D models only)
RS-232
9-pin D-Sub socket
RS-485
Terminal connector
Power Source
100 ~ 240 VAC
Power Consumption
150 W max
Dimensions
430 (W) x 410 (D) x 88 (H) mm ; 16.9” (W) x 16.2” (D) x 3.5” (H)
Weight
6.35 kg ( 14 LBS)
PAL
352 x 288: 400 IPS
704 x 288: 200 IPS
704 x 576: 100 IPS
4
Ambient Temperature
0°C ~ 40°C ; 32°F ~ 104°F (20%~80% humidity)
Remote Control
Handheld IR remote control; RS-485 keyboard EKB-500 (optional)
5
1.4 FRONT PANEL
Your primary interaction with your new DVR will be through the Front Panel buttons and their
corresponding buttons on the included Remote Control. Take a moment to learn where the keys are as the
remainder of the manual will refer to them often.
Figure 1-1 Front Panel
1)
2 x USB-2.0 port for USB mouse, USB-Flash-Drive
2)
Multiview Keys:
16x
NOTE:
4x
9x
13x
10x
PiP
The LED will show the selected screen layout.
The Multiview keys are only active in Main monitor - operation.
3)
Channel keys 1~16 / 1~8 for full screen display of selected channel. The LED will
show the active channel.
4)
DVD+RW:
5)
DISPLAY:
The DISPLAY key switches titles and status messages on the Screen in 4
steps. For details please consult chapter 4.9 DISPLAY.
DVD+RW drive for video data export. (for D model only)
6
Sequence key for automatic switching of a defined camera sequence
6)
SEQ:
7)
ZOOM: 2x electronical zoom.
For details please consult chapter 4.12 ZOOM.
NOTE:
The Zoom key is only active in Full screen at Main monitor.
8/9) MONITOR: The MONITOR key switches operation between MAIN and CALL. The active screen will
be Main monitor when LED is in “M” and Call monitor when LED is in “1”. For more details, please refer to
Chapter 4.11 MONITOR .
The SEARCH key opens the SEARCH menu, details in chapter 4.13 SEARCH.
10)
SEARCH:
11)
COPY:
12)
IR Receiver:
13)
HDD1:
14)
Key lock: Lock for hard disk door (only for HD removable model)
15)
HDD2:
Removable SATA HDD #2 (only for HD removable model)
16)
REC:
RECORD key for manual start of recording / recording standby (event recording).
LED will be ON if DVR is recording or in record standby
17)
STOP:
STOP key for Playback and Record
18)
BACK:
Reverse Playback key
19)
PAUSE: Image freeze in playback mode
20)
PLAY:
The COPY key opens the menu for video data export, details in chapter 4.14 COPY.
Receiver for IR remote control
Removable SATA HDD #1 (only for HD removable model)
Playback key
21) ENTER: Enter Key for menu operation and alarm acknowledge Turn camera audio ON/OFF when
viewing full screen camera. For more details, please refer to Chapter 3.2.1.
Used to bring up Main Menu or exit from sub-Menus.
22)
MENU/ESC:
23)
JOG/SHUTTLE: Shuttle (outer wheel): In playback mode, use the SHUTTLE for fast forward / fast
reverse playback.
7
JOG (inner wheel): In PAUSE mode, use the jog to move frame by frame. Within
menu functions, use the jog to adjust the values / parameters. Use Jog to highlight
individual cameras.
Use either Shuttle or Jog to switch between MENU parameters.
24)
POWER: LED indicating power on.
25)
HDD1/2: LED indicating HDD1 / HDD2 active
(HDD1: Internal HDD 1~4, HDD2: External HDD 4~8)
26)
LAN:
27)
ALARM: LED for alarm status
LED for network traffic
8
1.5 REAR PANEL
During initial setup you will be connecting your DVR to multiple input and output devices. This is done
through the rear panel.
○,2 ○,5
gdg
○,1
○,6
○,3
○,4
Fehler! Fehler!
○,7
○,8
○,9
Fehler!
Figure 1-2 Rear Panel
○,1 POWER:
Power socket for external power supply, 100~240VAC power source
○,2 Audio output:
Audio output
○,3 Audio inputs: Audio inputs 1~16(1~8 for EDR8)
○,4 MAIN monitor:
Main monitor for live and playback display and on-screen display
○,5 CALL monitor:
CALL monitor output. Spot monitor for full screen live display, sequence mode and
alarm camera switching
○,6 Video inputs: PARAGON8:
VIDEO IN (1~8): BNC video inputs for 1 Vpp Composite video signals, automatic 75
Ohm termination (high impedance switching upon loop-through output load)
PARAGON16:
VIDEO IN (1~16): BNC video inputs for 1 Vpp Composite video signals, automatic 75
Ohm termination (high impedance switching upon loop-through output load)
9
○,7 Alarm inputs: 8 (EDR8) resp. 16 (EDR16) alarm inputs for dry contacts, programmable NO or NC in
alarm menu.
○,8 Alarm outputs: 4 x NO/NC alarm output relay.
○,9 LAN:
RJ45 network socket
○,10 RS232 socket:
9-pin D-Sub control input for RS-232
○,11 RS485 socket:
For remote control via RS-485 keyboards and telemetry control
○,12 eSATA port: Used for external SATA HDD bay
10
Chapter
2
2 INSTALLATION
2.1 VIDEO INPUTS/OUTPUTS INSTALLATION
Cameras have to be cabled with 75 Ohm video cable, e.g. RG-59, RG-12 and suitable BNC plugs.
Due to inappropriate absorbability, 50 Ohm coax cable (e.g. RG58), antenna cable and further types of
coax cable are not suitable.
11
All connected video sources must provide a 1 Vpp NTSC/EIA or PAL/CCIR standard video signal
(depending on DVR version PAL / NTSC).
When interconnecting transmission lines (twisted pair, fibre optics, radio) to the video inputs, make sure all
receivers are accurately calibrated.
The Main monitor can be connected to BNC, Composite, or VGA monitor output.
NOTE: VGA monitor must support 800x600@60Hz resolution.
For local DVR operation, MAIN monitor connection is required. Call monitor connection is optional.
12
2.2 AUDIO INSTALLATION
The PARAGON DVRs provide 16/8 audio inputs and 1 audio output.
The inputs are designed for max. 1 Vpp @ 20 KOhm input.
The installation has to be effected with audio coax cable and RCA plugs.
The output provides a max. 1 Vpp @ 20 KOhm output line audio signal and may be connected to e.g. a
monitor‘s audio input. The direct connection of (passive) speakers is not supported.
ATTENTION: The direct connection of a non-amplified microphone is not supported (a microphone
amplifier is required).
AUDIO RECORDING FUNCTIONALITY:
Audio recording is activated / deactivated in the RECORD menu (chapter 5.4.1) for all channels.
Audio of all channels is always recorded together with (each) video and is independent of the image
recording rate.
During playback/live, use the JOG to select camera and press ENTER to turn audio ON or OFF.
13
2.3 ALARM / CONTROL CONTACTS INSTALLATION
The PARAGON alarm inputs can be used for recording start or recording rate adjustment. Furthermore,
alarm reactions such as camera switching to monitors, buzzer, e-mail and network alarm are available. 4
alarm output relays can be switched if required.
Additionally the PARAGON DVR provides 4 x TTL - level control outputs with similar functionality as the
relay outputs.
2.3.1
Alarm Input Contacts
PARAGON8 provides 8 alarm inputs, PARAGON16 provides 16. All inputs are programmable N.O. (Normal
Open) or N.C. (Normal Closed)
Inputs have to be switched by dry contacts.
Alarm input with N.O. (Normal Open) contact
in idle state
Alarm input with N.C. (Normal Closed) contact
in idle state
All settings are programmed in the ALARM menu (chapter 5.5.1).
2.3.2
Control Input Contact
The Control Input CTRL IN is a N.O. (Normal Open) contact. Changing to N.C. is not possible.
Control Input relay in idle state
The Control Input Contact CTRL IN is defined in I/O Control menu (
possible functions:
14
chapter 5.10.4) for following
1. Playback: Playback is active as long the contact is closed. This function is helpful in
combination with the "Quickplay" function (
chapter 5.4.3)
CTRL IN
CTRL IN
GND
GND
Idle state
2. Record:
Playback
The input switches to Record (or Record Standby) as long the contact is closed.
CTRL IN
CTRL IN
GND
GND
Idle state
Record / Record Standby
3. Armed / Disarmed: If the contact is closed, the DVR will switch off alarm (alarm contact and motion
alarm) operation. System alarm events are always active.
CTRL IN
CTRL IN
GND
GND
DVR armed
2.3.3
DVR disarmed
Alarm Output Relay
The relay outputs provide either Normally Open or Normally Closed dry contacts.
Output relay in idle state
2.4 RS-485 keyboard / PTZ Installation
All PARAGON functions can be remote-controlled by the EKB-500 universal keyboard. Using the EEPbus
protocol, digital video recorders, keyboards and speed domes can be installed on one single RS-485 bus.
One system can comprise up to 8 keyboards.
15
2.4.1
General RS-485 bus installation
The EKB-500 keyboard uses an RS-485 simplex wiring; the signal is transferred via a single twisted pair
line. CAT5 network cable is recommended, UPT version (unshielded) is sufficient for normal application. A
shielded cable should be used if the installed cables are expected to be highly susceptible to interferences.
The number of devices installed in one bus is limited to 32, and the maximum cable length is 1200m. Both
of these can be expanded using a signal distributor (see below).
Both the first and the last device in series should be terminated with 120 Ohm resistance in order to
minimize line reflections.
RS-485 bus serial wiring
Cable length from box to device („Stubs“) has to be limited to 2m using connector boxes.
RS-485 bus serial wiring with connector boxes and connection cable
A direct RS-485 bus star wiring is not supported unless using a signal distributor (see below).
Improper RS-485 bus star wiring
An RS-485 signal distributor may be used to use a star wiring configuration.
Star wiring with RS-485 signal distributor
16
An RS-485 distributor can also be used to increase the maximum number of devices on the bus as well as
the total range. Each distributor output provides another RS-485 bus. This allows each output to extend an
additional 1200m, and it also enables the additional connection of 31 further devices to each output (the
output itself represents one device).
The maximum system expandability depends on the RS-485 address range of the installed devices.
System expansion with RS-485 signal distributor
ATTENTION: Most signal distributors are unidirectional! This means that the signal only flows from the
input towards the outputs. Therefore, e.g. the interconnection of several keyboards is not possible with
these types of signal distributor!
2.4.2
RS-485 socket pin assignment
The two RS-485 input RJ-45 sockets are looped through and pin-compatible. The following RJ-45 pin
assignment has to be considered for connection:
Pin 6: RS-485 - (B)
Pin 3: RS-485 + (A)
17
2.4.3
EKB-500 connection with network patch cable
For a simple, short distance installation, recorder and keyboard can directly be connected using a standard
CAT5 network cable (patch cable, uncrossed!).
2.4.4
EKB-500 connection to several DVRs
For long distance installations connecting several DVRs, the use of the optional EDA998 connection kit is
recommended:
For further details on keyboard connection, please refer to the EKB-500 manual.
RS-485 port communication settings are configured in the I/O CONTROL menu (
System Setup: I/O - control).
2.4.5
chapter 5.10.4
Speed Dome Installation
Speed dome or telemetry receiver pan/tilt/zoom control is available through web browser or the optional
PowerCon software if the DVR is connected to a network. Local telemetry control is provided by USB mouse control or by the optional EKB-500 keyboard.
Supported protocols: EverFocus, ED2200/2250, Pelco-D, Pelco-P
Required DVR settings: RS-485 receiver address in CAMERA menu
(
chapter 5.10.4.)
RS-485 parameters and protocol in the I/O CONTROL menu
(
chapter 5.10.4.)
ATTENTION: Some Pelco-D / -P protocol domes and receivers require an address offset of -1, i.e. the
address assigned to the dome / receiver in the DVR camera menu must be 1 below the address set in the
dome / receiver itself!
2.5 RS-232 Connection
1 2 3 4 5
6
7 8 9
Pin
2
3
5
Function
TXD
RXD
Ground
18
2.6 USB-Mouse installation
Connect the USB mouse to one of the 2 USB ports. (This can be done while DVR is powered on)
NOTE: Recommended mouse types are Logitech® and Microsoft® wired USB wheel-mouse. Wireless
USB mouse is not supported.
2.7 NETWORK CONNECTION
This section only describes physical connection to an Ethernet network. This step must be completed
before the DVR’s can connect to the network. There are two basic types of connection:
2.7.1
Direct PC Connection through Crossover Network Cable
The point-to-point connection of DVR and PC requires a crossover (crossed) network cable. This type of
connection is ONLY used for direct connection to a single PC. Make sure that the PC is equipped with a
10/100/1000 Mbps compatible network connection.
Figure 2-1 Direct PC Connection
Pinout of crossover-cable
19
2.7.2
Network Connection through Patch Cable
The connection to an existing network requires a normal patch cable (straight-through). The illustration
shows the connection to a network switch, router, or modem.
Figure 2-2 Network Connection through Patch Cable
Pinout of straight patchcable
2.8 FINAL INSTALL PROCESS
Once you have completed the basic wiring connections, you are ready to turn on the DVR. Simply plug in
the power source. The POWER LED will light up if power is normal. Once the system has finished loading,
you can begin to set up the menu options for the DVR.
20
Chapter
3
3 MOUSE AND FRONT PANEL OPERATION
Paragon series DVR supports multiple sources to control the DVR. It can be controlled with a mouse, the
front panel, an EKB500, the handheld remote control, or serial command from RS232 port.
This chapter will cover the basic operation using mouse and front panel.
3.1 GENERAL USB MOUSE OPERATION
3.1.1
How to select a channel / Enable audio
1. In a view consisting of more than one channel, user can select a channel by clicking once on desired
channel screen. The selected screen will be highlighted by white frame.
2. Double clicking on a channel screen will display full screen of this channel.
3. To enable audio out, click audio icon(ex:
) at lower side of the screen. This system can have only
one audio out for one camera at a time. Click this button to select a camera for audio out, or to select
none audio-out mode.
3.1.2
OSD Root Menu
1. Right-click the mouse to obtain DVR control bar (see Figure 3-1 OSD Root Menu ). When you move the
mouse over each icon, the appropriate title will be displayed on top of the control bar.
Figure 3-1 OSD Root Menu
2. Click on any icon to perform that action. These actions are covered in detail in Chapter 4.
3. Click the “X” in the top-right corner to close the DVR control bar.
3.1.3
Operation in Configuration Menu
The Main menu (shown in Figure 3-2 OSD Menu) is divided into 3 main sections.
21
Fehler!
Fehler!
Fehler!
Figure 3-2 OSD Menu
○,1 In section 1, there are ten setup options available. Move the mouse over an icon and click to select it.
○,2 In section 2, the categories for the selected icon will be displayed. Click on a word to select it.
○,3 In section 3, all the details for the selected option will be available. Click on a field to make changes.
3.1.4
Component Options
The following are examples of different fields available in the Configuration menu.
Textbox: Click on the box and an on-screen keyboard will appear. (see
below)
Dropdown box: Click on the down arrow to see all selections, then
directly click on an option to select it.
Check box: Click on the box to enable it (checked) or disable it (unchecked).
Button: Click the button to execute the function.
Bar: Click and hold on the bar to adjust the cursor Left or Right.
22
* Note about on-screen keyboard:
Click on a button to input that character.
The buttons on the right and bottom have the following functions:
Delete
Done
All Caps
Space
←
→
Cancel
Delete the letter
Confirm the selection
Switch to capital letters
Enter a space
Move to left
Move to right
Cancel and exit from the keyboard
23
3.2 GENERAL FRONT PANEL OPERATION
3.2.1
How to select a channel / Enable audio
1. In a view consisting of more than one channel, turning Jog or Shuttle can scroll through each channel
that is displayed. The selected channel will be highlighted by white frame.
2.
While one channel is selected, click “Enter” button to turn Audio On/ Off.
3.2.2
OSD Root Menu
1. Press “Menu” key to obtain DVR control bar. Use Jog or Shuttle to scroll over each icon. The title for
each icon will be displayed on top of the control bar.
2. Press “Enter” key on any icon to perform that action. These actions are covered in detail in Chapter 4
3. Press “Menu” to close the DVR control bar.
3.2.3
Front Panel Key Review
The basic principle of front panel operation is to use Jog and Shuttle to navigate among the menu items.
Use “Enter” key to confirm a selection or enter the next level menu. Press “Menu” key to enter the Main
Menu or exit from the current level of the menu.
3.2.4
Operation in Configuration Menu
Press “Menu” and press “Enter” with “Configuration” icon highlighted to bring up Configuration menu.
NOTE: If password is active, you will need to log in first. Refer to “4.2 LOGIN” for information on logging in.
The menu (shown in Figure 3-3 (OSD Menu) ) is divided into 3 main sections.
24
Fehler!
Fehler!
Fehler!
Figure 3-3 (OSD Menu)
○,1 In section 1, there are ten setup options available. Use Jog or Shuttle to highlight an icon and press
“Enter” to select it.
○,2 In section 2, the main options for the selected icon will be displayed. Use Jog to highlight an option
and press “Enter” to select it.
○,3 In section 3, all the details for the selected option will be available here. Use Jog to move between
items and press “Enter” to make changes.
Note: press “Menu” button to go back to the previous menu section.
3.2.5
Component Options
Textbox: Press Enter key and an on-screen keyboard will appear. (see
below)
Dropdown box: Press “Enter” key to show the available options. Use Jog
to highlight the desired option and press “Enter” again to select it.
Check box: Press “Enter” key on a setting to enable it (checked) or disable it (unchecked).
Button: Press “Enter” key to execute the function.
25
Bar: Press “Enter” key to activate the slider, then use Jog to adjust the setting. Press
“Enter” again to finalize the changes.
26
Chapter
4
4 GENERAL DVR OPERATIONS
This chapter introduces the operations on major functions including playback, layout change, sequence,
triplex operations, copy, and search.
4.1 RECORD
By default, the Paragon series DVR will always be in record mode. When the DVR is turned on, it will start
to record.
The exceptions are:
1. Paragon DVR will not record any uninstalled cameras (Refer to section 5.3.1 for more detail)
2. If a schedule is active, Paragon DVR will follow the record settings of the schedule.
4.2 LOGIN
In order to access Paragon options, users may be asked to log in for authority identification. To log in,
follow these steps.
1. Click (or press “Enter” key) on the Configuration icon to bring up the following screen:
Figure 4-1 Login page
2. Select the user name from the drop-down list and input the password. The defaults are:
User name: admin (lower case)
Password: 11111111
27
+ To input password by mouse: click the password field to bring up the on-screen keyboard (see Figure 4-2
On-screen Keyboard). Click on each button to input the desired characters for the password. When finished,
click “Done” on the on-screen keyboard to confirm the password.
+ To input password using front panel: press “Enter” key to show the on-screen keyboard (see Figure 4-2
On-screen Keyboard). Use Jog or Shuttle to highlight each character and press “Enter” key on front panel
to input the selected characters. When finished, highlight “Done” and press “Enter” key on front panel to
confirm the password.
+ Click (or press “Enter” key) on “Login” button to log in to the system.
Figure 4-2 On-screen Keyboard
4.3 SELECT CAMERA OPERATION
Paragon is a pentaplex DVR, user can control each camera individually. User can control camera which
has been selected. For camera selection:
Mouse: Right-click the screen, there will show a white frame on screen if the camera has been selected.
When in split display mode, press same layout icon in layout menu to select all.
Front panel: Use Jog to change selection. Turn Jog one more step to select all camera at last turn(EX:
when camera16 is selected, turn jog one more step can select all)
4.4 CHANGE AUDIO OUTPUT OPERATION
Use Jog to select a camera and press “Enter” key to switch audio output to that camera. An audio icon
will appear on the screen.
4.5 PLAYBACK
To playback:
By mouse: Right-click to bring up the menu bar and click on
28
to enter Playback Menu.
By front panel: Press
key to enter Playback Setup Menu.
A playback bar will show as the figure below:
1 2 3 4
9
10 11 13
12 10 10
5 6 7 8
2009/05/25 09:09:30PM
2009/05/25 09:09:40PM
14
15
2009/05/25 09:10:30PM
16
1. Stop key: press to stop playback
2. Slow Reverse key: press to slow reverse playback
3. Pause key: press to pause playback
4. Slow Forward key: press to slow forward playback
5. Fast Reverse key: press to fast reverse playback
6. Reverse key: press to reverse playback
7. Forward key: press to forward playback
8. Fast Forward key: press to fast forward playback
9. Time bar: Move the cursor on the time bar to select time to playback(The start time and end time of
time bar is showed below)
10. “+” and “-“ signs are used to adjust time scale level. Press “+” or “-“ to select between L1 ~ L5. When
change level, the start time and end time of time bar will change)
L1: Whole time bar is 2 days
L2: Whole time bar is 30 hours.
L3: Whole time bar is 1 hour.
L4: Whole time bar is 10 minutes.
L5: Whole time bar is 1 minute.
11. Express copy: Press to start express copy when camera is in playback (only one camera)
12. Playback speed
13. Press “X” to close playback bar.
14. Start time of time bar
15. Current playback time
16. End time of time bar
29
4.6 PTZ
4.6.1
General PTZ control
Right-click to bring up the menu bar and click on
to enter PTZ Menu.
The following actions can be performed using the PTZ Menu:
1. Use Direction Arrows (up, down, left, right) to move the camera to the desired
direction and angle.
2. In Zoom option, Click “Z+” to zoom closer or “Z-” to zoom farther away.
3. In Focus option, click “F+” to increase the focus or click “F-” to decrease the
focus.
4. In Iris option, you can increase the amount of light by clicking “I+” or decrease
it by clicking “I-“.
5. To program a preset position
a. Move PTZ camera to the specified position
b. Click “Preset” button
c. Click the number of the desired position (This will be displayed in the box)
d. Click “Set” button
6. Steps to jump to a preset position
a. Click “Preset” button
b. Click the number of the desired position
c. Click “Go” button
7. Shortcut steps for presets #1-9
a. Click digit 1-9 button without clicking any other buttons
8. Steps to delete a preset position
a. Click “Preset” button
b. Click the number of the desired position
c. Click “Delete” button
9. Steps to run Auto Pan
a. Click “Auto Pan” button
10. Pattern Operation (Pattern is the “0” Tour in Everfocus and Pelco PTZ
cameras)
a. Click “Pattern” button
11. Steps to run a tour
a. Click “Tour” button
b. Click the number of the desired tour
c. Click “Go” button
12. Steps to remove a tour
a. Click “Tour” button
b. Click the number of the desired tour
30
c. Click “Delete” button
Click “C” to clear the digit in cell
Click “X” at top-right corner to close PTZ menu.
Click “Exit” to leave PTZ function.
4.6.2
Express control PTZ
When PTZ menu is closed, the mouse cursor will change to a different icon in different areas of the screen.
User can control PTZ direction, zoom, and focus by clicking directly on screen.
1
2
3
4
5
Focus +
6
Zoom +
7
8
9
Focus -
10
Zoom -
11
12
15
16
13
14
Figure 4-3 Express Control PTZ
The screen is divided into a 4x4 grid. The function of each section is defined as below:
• 1: PTZ pan/tilt left and up
• 2, 3: PTZ tilt up
• 4: PTZ pan/tilt right and up
• 5, 9: PTZ pan left
• 8,12: PTZ pan right
• 13: PTZ pan/tilt left and down
• 14, 15: PTZ tilt down
• 16: PTZ pan/tilt right and down
• 6: Focus closer
• 10: Focus further
• 7: Zoom in
31
•
11: Zoom out
32
4.7 LAYOUT
The Paragon DVR has a total of seven display modes available. The different available layouts are shown
below:
(Full screen)
(PIP)
(10 screens)
(4 screens)
(13 screens)
(9 screens)
(16 screens)
NOTE: PIP display is not available in Playback mode
To change layout, follow the steps below:
By mouse: Right-click to bring up the menu bar and click
to scroll through each display option.
By front panel: Push the appropriate display button on the front of the DVR (see red marker in below
image).
4.7.1
Bring to full screen mode
By mouse: Double left-click on the selected channel to put that camera in full screen mode.
33
By front panel: Press any channel key to bring that channel to full screen mode.
4.8 CHANNEL SWITCHING
Use this function to change channel position
1. Select one camera
2. Press Channel button
.
3. Click on the channel number you wish to switch on channel bar. The display of channel will be switched.
EX: Select camera1 and enter Channel menu and choose “2”, than camera1 will show on position of
camera2, camera2 will show on position of camera1
4.9 DISPLAY
1. Press Display button
on menu by using mouse or press “Display” button on the front panel.
2. Press once to show camera information. Please see the following table for status representation.
Recording
Playback
Fast forward
Fast backward
Back
Alarm
Motion
Video loss
Express copy
Audio out
pause
3. Press again to show status information. Please see the following table for status representation.
Alarm
Audio 1~16
Control call monitor
Event
Fan failure
HD failure
HD temp. too high
Monitor 1 status
Motion
New firmware
No network
Record in HD1
Record in HD2
Seq.
Video loss
34
4. Press again to show both status information and camera information.
5. Press again to hide all information.
4.10 SEQUENCE
1. By mouse: Click Sequence button
to enter the auto sequential switching mode.
2. By front panel: Click Sequence button on front panel to enter the auto sequential switching mode.
4.11 MONITOR
The DVR can connect to main monitor and call monitor simultaneously, but only one of them can be
controlled at one time. This feature allows user to switch control between two monitors.
Switch control by using a mouse
Click on “Monitor” button in menu or click global information icon “
“
“ button means the main monitor is selected. “
” to switch control to call monitor.
“ button means the call monitor is selected.
Switch control from front panel
Click “Monitor” button on front panel to switch control of monitor. The light right next to “Monitor” button
indicates which monitor is active: “M” indicates main monitor and “1” indicates call monitor.
Operation of Call Monitor OSD
View: Click this button to view different layouts.
Change: Switch channels.
Display: Turn OSD display on/ off.
Sequence: Turn sequence on/off.
Monitor: Click this button switch control to main monitor.
35
4.12 ZOOM
1. Make sure no cameras are in playback mode
2. Select one camera
3. Right-click to bring up the menu bar and click
button, or press ”Zoom” key on front panel.
4. When in ZOOM mode, the mouse cursor will change to a different icon in different areas of the screen.
User can control PTZ direction, zoom, and focus by clicking directly on screen:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Figure 4-4 Zoom Express Control
The screen is divided into a 4x4 grid. The function of each section is defined as below:
• 1: Left and up
• 2, 3: Up
• 4: Right and up
• 5, 9: Left
• 8,12: Right
• 13: Left and down
• 14, 15: Down
• 16: Right and down
• 6, 7, 10, 11: Not used
36
4.13 SEARCH
By mouse: Right-click to bring up the menu bar and click
to enter Search Menu.
By front panel: Press ”Search” key to enter Search Menu directly.
4.13.1 Time Search
Figure 4-5 Search Menu – Time Search
Play From: Select the time to be searched by choosing the Date and Time.
Click on the “Play” button to start search. The DVR will automatically play the video being searched. DVR
will play the nearest time if there is no data in selected time.
In search playback mode, press stop button to come back to search menu.
37
4.13.2 Event Search
Figure 4-6 Search Menu – Event Search
From: Select starting date and time
To: Select ending date and time.
Camera: Select which cameras to search for.
Event: Select which event type(s) to search for. Choose from Alarm, Motion, Video Loss, or Others.
Click on the “Search” button to start searching. The search results will be shown as a list of events.
38
Prev Page: Go to previous page.
Next Page: Go to next page
Unlock: Unlock the item if the item is locked
Lock: Lock the item (The selected item will show Locked or Partial)
Delete: Delete item if it is not locked
Play: Playback selected item
Copy: Copy selected item
In Lock status, there will show “Partial” in some case, it means there has a time period which has been
locked in whole search result time period.
4.13.3 Motion Search
In order to perform a Motion Search, motion must be enabled first (see “Chapter 5.3.3”).
39
Figure 4-7 Search Menu – Motion Search
From: Select motion search starting date/time.
To: Select motion search ending date/time.
Camera: Select camera number to be searched.
Figure 4-8 Search Menu – Set Grid
Grid Setting:
40
Choose which areas of the motion grid will be included in the search. The areas you set in motion search
must also be active in the motion settings of the Camera Setting Menu. Use the mouse to drag your desired
area. Press “Set All” button to select the entire area. Press “Clear All” to deselect the entire area. Press
“Save & Back” to save the motion grid setting and go back to Motion Search menu. Press “Cancel” to skip
edition
Press “Search” button to start searching.
4.14 COPY
To bring up Copy menu:
By mouse: Right-click to bring up the menu bar and click on
to enter Copy Menu.
By front panel: Press “Copy” key to enter Copy Menu directly.
Figure 4-9 Copy Menu
Camera: Select which cameras will be archived. Choose “Select All” to select all the cameras.
Player: Check the box to include the ePlayer program as part of the copy.
Start Date/Time: Select the starting date/time to be archived.
End Date/Time: Select the ending date/time to be archived.
41
Archive To: Select whether you want to copy to USB or DVD.
Data Size: Shows the estimated total size for the selected time period.
Archive Now: Press “Archive” button to start archiving.
4.15 LOGOUT
Right-click to bring up the menu bar and click
(see Figure 4-10).
button to bring up the Logout Confirmation window
Figure 4-10 Logout Confirmation window
Press “Yes” button when you are ready to logout from the system. You will need to login again before
accessing any other options.
42
Chapter
5
5 DVR CONFIGURATION
This chapter will walk you through the DVR Menu Settings step by step and show you how to set the DVR
for your specific application.
5.1 CONFIGURATION MENU
1. To bring up the Main Menu, press the “Menu/Esc” key on the front panel or right-click with the USB
mouse to bring up the OSD menu bar.
2. Press “Enter” or left-click on the “Configuration” icon “
” to enter configuration menu.
5.2 EXPRESS
Figure 5-1 Express Menu is a screen shot of the EXPRESS SETTING MENU. This menu is used to
configure express setting for all 16 cameras. For example, if user selects Event Only in Record Mode and
presses Apply button, all 16 cameras will be set to Event only. If user selects Blank in Recording Mode and
presses Apply button, 16 cameras will keep their own current record modes without changing.
Figure 5-1 Express Menu
43
Date: Set the current date of DVR.
Time: Set the current time of DVR.
Resolution: Select recording resolution based on video format.
NTSC: 704x480 / 704x240 / 352x240
PAL: 704x576 / 704x288 / 352x288
Record Mode:
Blank: No change for Record mode
Normal+Event: Normal recording plus event recording.
Event Only: Event recording only.
Schedule Rec: Schedule recording.
Record With:
Blank: No change for Record with
Max. Recording Days: Set the maximum recording days. Available selection will be shown in the next
column, including 1, 3, 5, 7, 14, 20, 30, 40, 50 and 60 day. DVR will auto adjust relative settings for 16
cameras to fit the selected max recording day. For more detail, please refer to APPENDIX B:
CHANGING RULE FOR EXPRESS SETUP
Preset Settings: Select preset setting or recording quality. Available options are Best Quality, Standard
and Extended Record in the next column. For more detail, please refer to APPENDIX B: CHANGING
RULE FOR EXPRESS SETUP
Network Type:
Fixed IP: User can set a fixed IP for network connection.
44
DHCP: DHCP server in LAN will automatically assign IP for network connection.
PPPoE:
IP Address: This field shows the current IP Address for the DVR. A Fixed IP address must be set
manually. If DHCP or PPPoE is selected, this value will be assigned automatically.
Subnet Mask: This field shows the subnet mask for your network so the DVR will be recognized within the
network. If DHCP or PPPoE is selected, this value will be assigned automatically.
Gateway: This field shows the gateway for your network so the DVR will be recognized within the network.
If DHCP or PPPoE is selected, this value will be assigned automatically.
Apply: Press “Apply” button to save and apply Express settings to DVR. The system will automatically
adjust recording frame rate according to settings. The following message will pop up, press YES to change
Resolution, Recording frame rate and Quality depending on your express setting.
5.3 CAMERA SETTING
is a screen shot of the CAMERA SETTING MENU. This menu is used to configure individual
camera settings.
Figure 5-2
45
Figure 5-2 Camera Menu-Basic Setting
5.3.1
Basic Setting
Camera: Select the camera number.
Title: The title setting allows you to assign a title to selected camera. Each title supports up to 16
characters. The on-screen keyboard will appear when you click the title option.
Install: Check the box to enable the current camera. To take full advantage of the DVR’s recording
abilities, any unused cameras should have this option disabled.
Covert: Check the box to hide the camera picture in live and sequence modes. However, the image will still
be recorded and can be played back by any user who has playback rights.
Record Mode: 2 record modes are available.
Normal + Event: This recording mode includes continuous and event recording.
Event Only: Video will be recorded only when events occur.
46
Resolution: Select recording resolution based on video format.
NTSC: 704x480 / 704x240 / 352x240
PAL: 704x576 / 704x288 / 352x288
Record Quality: Select an image quality for recording. There are five different qualities available: Superior,
High, Standard, Basic and Low. A higher image quality uses more HDD space.
Normal Speed: Frame rate in images per second (IPS) for continuous recording. The speed is limited to
the maximum recording rate of the DVR (displayed in the bottom left corner) divided by the number of
installed cameras. If the resolution option is changed, the unit of this field will also be changed.
Recording capacity for all 16 cameras (shown next to the Normal Speed field): The number here
indicates the remaining recording capacity available for all 16 cameras. When this number is positive, it
means there is still recording capacity. If this number is negative, it means the recording capacity has
been exceeded, and the user must lower Normal Speed or Resolution. This number must be positive
before saving the changes. Otherwise, a pop-up window will display “Total FPS exceed maximum
recording rate, discard changes!” and the settings for all cameras will return to previous values.
Event Speed: Frame rate in images per second (IPS) for event recording.
PTZ ID: When using a PTZ Camera, this ID must match the ID used by the connected camera in order to
control the camera using the DVR. Click “Done” to confirm selection, “Cancel” to cancel selection.
Apply To: This button can be used to copy the recording settings to other cameras. Select which cameras
you wish to copy to. "Select All" selects all cameras, “Unselect All” deselects all cameras. Click “OK” to
copy the settings or "Cancel" to exit without copying.
47
5.3.2
Video Adjust
Figure 5-3 Camera Menu – Video Adjust
Camera: Select the camera you wish to adjust. “Title” will change to the name of the selected camera.
Brightness: Adjusts how bright/dark the picture appears. If details appear to be lost in the shadows or
darker regions, try increasing the Brightness. If the image appears too saturated or if the colors appear
overwhelmed by glare, try decreasing the Brightness.
Contrast: Adjusts the total amount of light output from the display. If details are lost or lines appear
distorted, try decreasing the contrast.
Color: Adjusts the amount of color information in the picture.
Apply To: This button can be used to copy the video settings to other cameras. Select which cameras you
wish to copy to. "Select All" selects all cameras, “Unselect All” deselects all cameras. Click “OK” to copy the
settings or "Cancel" to exit without copying.
48
5.3.3
Motion
Figure 5-4 Camera Menu – Motion
Camera: Select the camera you wish to adjust. “Title” will change to the title name of the selected camera.
Enable: Check box to enable motion detection. Other motion options will not be available unless this
feature is selected.
Log: Check box to record motion events in the log.
Main Monitor: Monitor display options when a motion event occurs.
No change: No change on the main monitor display.
Full screen: A full screen of the active camera will display on the main monitor.
Call Monitor: Monitor display options when a motion event occurs.
No change: No change on the call monitor display.
Full screen: A full screen of the active camera will display on the call monitor.
Pre-alarm Record: Check box to record several moments before the motion event. (Pre-alarm recording
rate will follow “Normal” frame rate setting)
Buzzer: Check box to enable buzzer when a motion event is triggered.
Email Notify: Check box to send email notification when a motion event is detected.
Network Alarm: Check box to send out a network alarm to client PC when motion occurs. (requires
PowerCon software and setting up Alarm Server in Network Setup menu)
49
Auto Lock: Check the box and the events will be recorded in the write protected segment of the Hard Disk.
(DVR will lock a period of time when alarm happen, the length of time will depend on DVR setting)
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action when motion is triggered.
Timeout: Alarm output lasts for the set time duration.
Permanent: Alarm will remain on until user presses “Enter” key on front panel.
Transparent: Alarm output continues as long as there is a motion event.
Trans+Timeout: Alarm output continues until event ends, then lasts for the set time duration.
Timeout Duration: Time duration selectable from 1 to 150 seconds.
Edit Motion Grid: Press this button to edit the motion grid (See Figure 5-5 Camera Menu – Motion Grid Setting ).
Sensitivity: Set the threshold value for sensitivity. Select from 1 (lowest) to 10 (highest).
Min Area: To avoid false detections by small objects this value defines, how many grids have to be
detected for generating a motion event. Select a value between 1 (default) to 5 grids.
Delay: Filter function for avoiding false alarms (set to 1 for the easiest trigger)
Preview: Turn off display for motion grid
Set All: Press this button to select the entire area.
Clear All: Press this button to clear all the grids selected.
Save & Back: Press this button to save the motion grid setting and return to motion setting menu.
Cancel: Press this button to cancel all changes and return to motion setting menu.
How to select motion grid by mouse:
1. Select left-up grid 2. Select right-down grid. 3. The area between left-up and right-down
grid will be selected.
50
Figure 5-5 Camera Menu – Motion Grid Setting
Apply To: This button can be used to copy the motion settings to other cameras. Select which cameras
you wish to copy to. "Select All" selects all cameras, “Unselect All” deselects all cameras. Click “OK” to
copy the settings or "Cancel" to exit without copying.
51
5.3.4
Video Loss
Figure 5-6 Camera Menu – Video Loss
Camera: Select the camera you wish to adjust, “Title” will change to the title name of the selected camera.
Enable: Check box to enable Video Loss.
Log: Check box to record video loss events in the log.
Pre-alarm Record: Check box to record several moments before the video loss. (Pre-alarm recording rate
will follow “Normal” frame rate setting)
Buzzer: Check box to enable buzzer when a video loss event occurs.
Email Notify: Check box to enable email notification when a video loss event occurs.
Network Alarm: Check box to send out a network alarm to client PC when video loss occurs. (requires
PowerCon software and setting up Alarm Server in Network Setup menu)
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action when alarm is triggered.
Timeout: Alarm output lasts for the set time duration.
Permanent: Alarm will remain active until user presses “Enter” key on front panel.
Transparent: Alarm output continues as long as there is a video loss.
Trans+Timeout: Alarm output continues until event ends, then lasts for the set time duration.
Timeout Duration: Time duration selectable from 1 to 150 seconds.
52
Apply To: This button can be used to copy the video loss settings to other cameras. Select which cameras
you wish to copy to. "Select All" selects all cameras, “Unselect All” deselects all cameras. Click “OK” to
copy the settings or "Cancel" to exit without copying.
5.4 RECORD & PLAY SETTING
Figure 5-7 is a screen shot of the RECORD & PLAY SETTING MENU. This menu is used to configure
basic recording and playback settings.
Figure 5-7 Record & Play Menu
5.4.1
Record
Record Audio: Check the box to record audio.
Record Overwrite: Check the box and disk will begin overwriting when full.
Schedule Rec.: Use schedule recording mode.
53
For Schedule recording, the only way to stop schedule recording is to turn schedule recording off.
Pressing any keypad on front panel to change schedule recording will not work during scheduling record
mode. When schedule recording is disabled, DVR will auto turn on recording
Time Stamp: Select if the time and date will display while recording. Choose from Top, Bottom, or Off.
Record Status Relay Output: Select from “NONE”, “1”, “2”, “3”, or “4”.
Auto Erase Video: The hard drive will automatically erase after the selected number of days. To use the
maximum hard drive space, choose “OFF”.
5.4.2
Built-in Cal.
The built-in record period calculator can give a rough estimation of the total recording time of the DVR with
current settings.
Figure 5-8 Record & Play Menu-Built-in Cal.
Motion: Enter the expected amount of hours per day using motion record.
Alarm: Enter the expected amount of hours per day using alarm records.
If total amount of Motion and Alarm hour more than 24 hours, it will assume that total motion and alarm
hours is 24 hours.
ESSTTIIM
Click on the “E
MAATTEE”” button to display the result at the bottom of the screen:
" xx days of data can be stored based on current setting"
54
5.4.3
Play
Figure 5-9 Record & Play Menu - Play
Quick Playback: Check the box to enable quick playback function.
Playback From X Seconds ago: When the DVR is put into playback, it will begin playing from the selected
time. Choose from 60 to 3600 seconds.
55
5.5 ALARM & EVENT SETTING
Figure 5-10 is a screen shot of the ALARM & EVENT SETTING MENU. This menu will walk you through
alarm and event setup.
Figure 5-10 Alarm & Event Menu - Alarm
5.5.1
Alarm
Alarm: Select the alarm number from 1 to 16.
Enable: Check box to enable alarm.
Log: Check box to record alarm events in the log.
Pre-alarm Record: Check box to record several moments before the alarm event. (Pre-alarm recording
rate will follow “Normal” frame rate setting)
Buzzer: Check box to enable buzzer when an alarm occurs.
Main Monitor: Monitor display options when a motion occurs.
No change: No change on the main monitor display.
Full screen: A full screen of the active camera will display on main monitor.
Call Monitor: Monitor display options when a motion occurs.
No change: No change on the call monitor display.
Full screen: A full screen of the active camera will display on call monitor.
56
Recording: Select which cameras will start recording when alarm happens.
Email Notify: Check box to enable email notification when an alarm occurs.
Input Type: This field is to change the type of alarm trigger.
N.O.: Normal Open contact.
N.C.: Normal Close contact.
Network Alarm: Check box to send out a network alarm to client PC when motion occurs. (requires
PowerCon software and setting up Alarm Server in Network Setup menu)
Active Camera: This field is for assigning the alarm to a specific camera. For example if you had an
external motion detector on camera one you would set this option to “1”.
Auto Lock: Check the box and the events will be recorded in the write protected segment of the Hard Disk.
(DVR will lock a period of time when alarm happen, the length of time will depend on DVR setting)
PTZ Preset: Select PTZ Preset from “1” to “255”. If the Active Camera is a PTZ speed dome, the alarm will
move the camera to the specified preset position for event recording. Click “Done” to confirm selection,
“Cancel” to cancel selection.
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action when alarm is triggered.
Timeout: Alarm output lasts for the set time duration.
Permanent: Alarm will remain active until user presses “Enter” key.
Transparent: Alarm output keeps working according to the signal of alarm input.
Trans+Timeout: Alarm output continues until event ends, then lasts for the set time duration.
Timeout Duration: Time duration selectable from 1 to 150 seconds.
Apply To: This button can be used to copy the alarm settings to other cameras. Select which cameras you
wish to copy to. "Select All" selects all cameras, “Unselect All” deselects all cameras. Click “OK” to copy the
settings or "Cancel" to exit without copying.
Alarm16 will be used to Trigger Alarm, Start Record, Start Playback and Arm/Disarm.
57
58
5.5.2
Event
This section covers internal system event warnings.
Figure 5-11 Alarm & Event Menu – Event
Event: Select from the following event types.
Fan Failure: The internal fans are equipped with rotation detection. Any fault of a fan will cause "Fan
Failure" event.
HD Temperature: Hard drive is over the safety warning temperature
HD Failure: If DVR fails to detect a HDD on start up, the system will create a HD failure event.
HD Full: If the DVR is not set to Overwrite in the Record Menu, an event will be created when all HDDs
are filled.
HD Off: If HDDs are switched off or are removed, the DVR will create a HD OFF event.
Power Loss: The DVR keeps a record of any time the system is powered off.
NOTES: When using a contact output for this feature, make sure the control output is 5V effective.
Record Stop: If recording is stopped, the DVR will create an event.
If an output is assigned to Record Stopped, any other events assigned for that alarm output will
automatically change to “None”.
Network Loss: If connection to network is lost, DVR will create a Network Loss event.
NOTE: This function only checks physical connection to the network. Any network behavior that blocks
connection (blocked ports, wrong IP setup, etc.) is not detected by this function.
Fan Failure:
59
Figure 5-12 Alarm & Event Menu – Event-Fan Failure
Log: Check box to record events in the log.
Buzzer: Check box to enable buzzer when a fan fails to work.
Email Notify: Check box to enable email notification when a fan fails to work.
Network Alarm: Check box to send out a network alarm to client PC. (requires PowerCon software and
setting up Alarm Server in Network Setup menu)
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action is locked to Transparent
60
HD Temperature:
Figure 5-13 Alarm & Event Menu – Event - HD Temperature
Log: Check box to record events in the log.
Buzzer: Check box to enable buzzer when hard drive’s temperature is over the “Temp. Warning Limit”.
Email Notify: Check box to enable email notification when temperature is over the “Temp. Warning Limit”.
Network Alarm: Check box to send out a network alarm to client PC. (requires PowerCon software and
setting up Alarm Server in Network Setup menu)
Stop Recording: Check box to stop recording when HD’s temperature is over the “Temp. Warning Limit”.
Temp. Warning Limit: Sets the trigger temperature for all other active settings in HD Temperature.
Choose from 55°C /131°F~85°C /185°F.
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action is locked to Transparent
61
HD Failure:
Figure 5-14 Alarm & Event Menu – Event - HD Failure
Log: Check box to record events in the log.
Buzzer: Check box to enable buzzer when no hard drive is detected.
Email Notify: Check box to enable email notification function when HD fails.
Network Alarm: Check box to send out a network alarm to client PC. (requires PowerCon software and
setting up Alarm Server in Network Setup menu)
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action is locked to Transparent
62
HD Full:
Figure 5-15 Alarm & Event Menu – Event - HD Full
Buzzer: Check box to enable buzzer when hard drive is full.
Email Notify: Check box to enable email notification when HD is full.
Network Alarm: Check box to send out a network alarm to client PC. (requires PowerCon software and
setting up Alarm Server in Network Setup menu)
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action when alarm is triggered.
Timeout: Alarm output lasts for the set time duration.
Permanent: Alarm will be continuously active until user presses “Enter” key.
Transparent: Alarm output remains active until event ends.
Trans+Timeout: Alarm output continues until event ends, then lasts for the set time duration.
Timeout Duration: The amount of time the buzzer sounds when the HD is full. Duration selectable from 1
to 150 seconds.
63
HD Off:
Figure 5-16 Alarm & Event Menu – Event - HD Off
Buzzer: Check box to enable buzzer when hard drive is off.
Email Notify: Check box to enable email notification when HD is off.
Network Alarm: Check box to send out a network alarm to client PC. (requires PowerCon software and
setting up Alarm Server in Network Setup menu)
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action when alarm is triggered.
Timeout: Alarm output lasts for the set time duration.
Permanent: Alarm will be continuously active until user presses “Enter” key.
Transparent: Alarm output remains active until event ends.
Trans+Timeout: Alarm output continues until event ends, then lasts for the set time duration.
Timeout Duration: The amount of time the buzzer sounds when the HD is off. Duration selectable from 1
to 150 seconds.
64
Power Loss:
Figure 5-17 Alarm & Event Menu – Event – Power Loss
Log: LOG is permanently checked for this feature. Power Loss events are always recorded by the DVR.
Email Notify: Check box to enable email notification when HD is off.
Network Alarm: Check box to send out a network alarm to client PC. (requires PowerCon software and
setting up Alarm Server in Network Setup menu)
65
Record Stop:
Figure 5-18 Alarm & Event Menu – Event – Record Stop
Log: Check box to record events in the log.
Buzzer: Check box to enable buzzer when DVR stops recording.
Email Notify: Check box to enable email notification when DVR stops recording.
Network Alarm: Check box to send out a network alarm to client PC. (requires PowerCon software and
setting up Alarm Server in Network Setup menu)
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”. (If an output is assigned to Record Stopped, any other events assigned for
that alarm output will automatically change to “None”)
Output Type: Output action when alarm is triggered.
Timeout: Alarm output lasts for the set time duration.
Permanent: Alarm will be continuously active until user presses “Enter” key.
Transparent: Alarm output remains active until event ends.
Trans+Timeout: Alarm output continues until event ends, then lasts for the set time duration.
Timeout Duration: The amount of time the buzzer sounds when DVR stops recording. Duration selectable
from 1 to 150 seconds.
66
Network Loss:
Figure 5-19 Alarm & Event Menu – Event – Network Loss
Log: Check box to record events in the log.
Buzzer: Check box to enable buzzer when network is lost.
Alarm Output: This will transmit a signal through one of the alarm outputs. It can be set to either “NONE”
(not active), “1”, “2”, “3”, or “4”.
Output Type: Output action when alarm is triggered.
Timeout: Alarm output lasts for the set time duration.
Permanent: Alarm will be continuously active until user presses “Enter” key.
Transparent: Alarm output remains active until event ends.
Trans+Timeout: Alarm output continues until event ends, then lasts for the set time duration.
Timeout Duration: The amount of time the buzzer sounds when DVR stops recording. Duration selectable
from 1 to 150 seconds.
67
5.6 SCHEDULE SETTING
Figure 5-20 is a screen shot
of the SCHEDULE SETTING MENU. In this menu you can set a unique timer to
start recording during a specified time period. This menu is used to configure Express Setup, Holidays and
Schedule settings.
Figure 5-20 Schedule Menu-Express Setup
5.6.1
Express Setup
Weekend Starts: Select day and time when weekend starts.
Weekend End: Select day and time when weekend ends.
Daytime Starts: Select daytime starting time. (Nighttime schedule ends when Daytime begins)
Daytime End: Select daytime ending time. (Nighttime schedule begins when Daytime ends)
Record Type: Select the type of recording for each time period.
Disabled: No recording during scheduled time period
Normal+Event: Continuous and Event recording
Event Only: Event recording only
Normal Frame Rate: Conntinuous FPS recording rate for the scheduled time period. The maximum rate is
limited to the DVR’s maximum recording rate divided by the number of active cameras. Selectable frame
rate includes 30fps, 15fps, 10fps, 7.5fps, 5fps, or 1fps.
Event Action: FPS recording rate for events. Selectable frame rate includes 30fps, 15fps, 10fps, 7.5fps,
5fps, or 1fps.
68
Event Action: Check this box to enable Buzzer, Alarm out, E-mail and Network actions when an event
occurs on the selected time period.
Apply: Press Apply button bring up a confirmation window. Select “Yes” to confirm and apply express
schedule settings or “No” to cancel changes.
5.6.2
Holidays
In addition to setting a weekly record schedule, user can also schedule recording for specific days of the
year.
Figure 5-21 Schedule Menu-Holidays
Data Type: Select either Holiday or Others. (Holiday and Others means two different group, you can assign
special days in these two group)
Recurrent Type: Choose how often each scheduled day should be recorded.
Disable: Recording is disabled.
One time: Records date only once.
Month/date: Repeats recording on the same specific date.
69
Month/weekday: Repeats recording on a specific day of the month/week.
Details: Specifies the date to be recorded.
Prev: Previous Page (30 Holidays Total)
Next: Next Page (30 Holidays Total)
5.6.3
Schedule
Figure 5-22 Schedule Menu-Schedule
Camera: Select a number to change the schedule for that camera. Each camera can be set on a 24 hour
time block for Holiday (Hol), Other (Oth), Sunday (Sun), Monday (Mon), Tuesday (Tue), Wednesday (Wed),
Thursday (Thu), Friday (Fri), or Saturday (Sat).
Time Bar: The time bar uses three different colors to distinguish each recoding mode.
Gray (No Rec): No recording during this time block.
Orange (E): Only events are recorded during this time block.
Blue (N+E): (Default) Normal and event recording during this time block.
To Set Schedule using Mouse
1. Click on desired start time block (no numbers on it) on a time bar. At this time, the selected block will
be highlighted in blue frame and the selected time bar will be highlighted by red frame.
There are 24 blocks on the time bar representing 24 hours respectively. Set a schedule start time by
clicking on a desired start time block on a time bar and clicking again to confirm it. At this time, the
selected block and all following blocks will turn gray, which means this gray timezone has been set to
the recording mode of gray(No Rec).
70
2. Click again to confirm, then a new number (for the new section) will show on this block and current and
all following blocks will turn to gray. This means this new gray timezone has a new record mode (No
record).
Change the section to different mode (with different color) by clicking on the first block of each section.
The color swatches from gray -> orange -> blue, everytime user click the first block of a section.
3. Repeat clicking on the first block (with number on it) of any timezone, this timezone will change from
one color to another, which means switching the record mode. The color switch sequence is gray>orange->blue.
Schedule Setting from front panel
1. Enter schedule setting mode: press Enter button to enter schedule setting mode. At this time, the
whole editing area at right-down side will be highlighted within a blue frame. See below image.
2. Enter camera selection mode: turn Jog knob to switch to Camera selection mode. When Camera
selection mode is selected, all 16 cameras will be highlighted in a blue frame. See below image.
3. Selecting camera: Turn Shuttle knob to select desired camera to configure. Selected camera number
will be highlighted by a blue frame. See above image.
4. Enter time bar editing mode: turn Jog knob to switch to time bar editing mode. When this mode is
selected, all 9 time bars will be highlighted within a blue frame.
5. Select desired time bar for setting: press Enter button, the first time bar will be selected for setting
and highlighted in a red frame. See below image. Press Jog to switch to desired time bar for setting.
71
6. Editing blocks in a time bar: when a time bar is selected (highlighted in red frame), press Enter
button, then the first block of this bar will be selected (highlighted in blue frame). Turning Jog knob to
switch to desired block as starting time, and press Enter button again to confirm. At this time, the
current and all following blocks will turn into gray, which means this gray timezone has been set to the
recording mode of gray(No Rec). User can also change the timezone to a different record mode (with
different color) by following instruction in next step.
7. Changing recording mode (color) of a timezone: Turn Jog knob to switch to the first block (with
number on it) of a timezone. Clicking Enter button, and this timezone will switch to another color, which
means switching to another record mode. The color switch sequence is gray->orange->blue.
Press “Edit Timezone” button to edit the time zone.
72
Figure 5-23 Schedule Menu-Schedule-Edit Timezone
Editing Timezone:
From: Displays schedule start time
To: Displays schedule end time
Record: Displays Record mode
Resolution: Select recording resolution.
NTSC: 704x480; 704x240; 352x240
PAL: 704x576, 704x288, 352x288
Normal: Frame rate in images per second for continuous recording. The speed is limited to the maximum
recording rate of the DVR divided by the number of installed cameras.
Event Speed: Frame rate in images per second for event recording. Event record speed can be set from 1
to 30 (25 for PAL).
Action: Check this box to enable Buzzer, Alarm out, E-mail, and Network when an event occurs.
Apply to Days: This button can be used to copy schedules to other days. Select which days you wish to
copy to. "Select All" selects all days, “Clear All” deselects all days. Click “OK” to copy the settings or
"Cancel" to exit without copying.
73
Apply to Cameras: This button can be used to copy schedules to other cameras. Select which cameras
you wish to copy to. "Select All" selects all cameras, “Clear All” deselects all cameras. Click “OK” to copy
the settings or "Cancel" to exit without copying.
74
5.7 NETWORK SETTING
Figure 5-24 is a screen shot of the NETWORK SETTING MENU. This menu is for configuring the DVR for a
network connection.
NOTE: Since every Network Configuration is different, please check with your Network Administrator or ISP
to see if your DVR requires specific IP addresses and/or port numbers.
Figure 5-24 Network Menu – LAN
5.7.1
LAN
Network Type:
Static IP: User can set a fixed IP for network connection.
DHCP: DHCP server in LAN will automatically assign IP for network connection
PPPoE: For direct connection to DSL ONLY. Verify with your ISP if they use PPPoE.
IP: This field shows the DVR’s current IP Address. A static IP address must be set manually. If DHCP or
PPPoE is selected, this value will be assigned automatically.
Subnet Mask: This field shows the subnet mask for your network so the DVR will be recognized within the
network. If DHCP or PPPoE is selected, this value will be assigned automatically.
Gateway: This field shows the gateway for your network so the DVR will be recognized within the network.
If DHCP or PPPoE is selected, this value will be assigned automatically.
DNS Server 1: This field shows the primary DNS server for your network. If DHCP is selected and an
internet connection is available, this value will be assigned automatically. This field must have a valid DNS
address in order to use the DDNS feature (see 5.7.3 for more detail).
DNS Server 2: This field shows the secondary DNS server for your network.
75
HTTP Port: Port number for HTTP/WEB communication.
Bandwidth Limit: Allows user to limit the bandwidth used by the DVR.
5.7.2
EMAIL
Figure 5-25 Network Menu – Email
SMTP Server: Assign the SMTP (e-mail) server’s name.
NOTE: For more reliable email service, use the server’s IP address.
SMTP Port: Assign the port number used by the SMTP server.
Authentication: Check this box if the SMTP server requires authentication (user name / password).
SSL: Check the box if mail server needs to be encrypted by SSL.
User name: Input the login user name if the SMTP server requires authentication.
Password: Input the password if the SMTP server requires authentication.
Sender Email: Input the e-mail address of the sender (DVR).
Receiver Email 1: Input the first e-mail address that event messages are sent to.
Receiver Email 2: Input the second e-mail address that event messages are sent to.
Receiver Email 3: Input the third e-mail address that event messages are sent to.
Email Subject: Input email subject.
76
5.7.3
DDNS
DDNS Server: Select either “EverfocusDDNS” or “www.dyndns.org” as the DDNS provider. If DDNS will
not be used, simply select “Disable”.
EverfocusDDNS
Figure 5-26 EverfocusDDNS
DVR Name: Input the desired name for the DVR
Register/Update: Click the button to submit and register the name to the Everfocus server.
77
www.dyndns.org
Figure 5-27 www.dyndns.org
Host name: Host name created through the dyndns account.
User name: User name of the dyndns account.
Password: Password of the dyndns account.
Confirm: Re-enter password.
Note: For more details on DDNS setup, please see “Chapter 8 - Everfocus DDNS Setup”.
78
5.7.4
Alarm Server
Figure 5-28 Network Menu – Alarm Server
Server IP1~3: IP address of client PC with installed PowerCon Software. The network alarm can be
transmitted to up to 3 addresses.
Protocol: Select the protocol type for alarm transmission:
UDP: User Datagram Protocol
TCP: Transmission Control Protocol
Port: Select the transmission port for network alarm messages
Network ID: The network ID is an identifier for the alarm transmitter.
79
5.8 DISPLAY SETTING
Figure 5-29 is a screen shot of the DISPLAY SETTING MENU. This menu will walk you through Monitor OnScreen Display (OSD) and Sequential setup.
Figure 5-29 Display Menu – Monitor OSD
5.8.1
Monitor OSD
These are the display options for the Main Monitor.
Main Monitor
Camera Title: Check the box to display camera titles.
Date/Time: Check the box to display current date/time.
Playback Date/Time: Check the box to display playback date/time.
Playback Status: Check the box to display playback status.
Event Status: Check the box to display event status.
HDD Status: Check the box to display hard drive status.
Text Insert: Check the box to display data transmitted from external RS232 device.
Main Monitor Output: This system supports both VGA and BNC monitor displays at the same time but
only one of them can have optimized display quality. Use this feature to select which output is optimized.
Call Monitor
Camera Title: Check the box to display camera titles.
Date/Time: Check the box to display current date/time.
80
5.8.2
Main M/T SEQ
Figure 5-30 Display Menu – Main M/T SEQ
Step: Sequence order. Cannot be changed.
Camera: Select which camera appears on the current step.
Dwell (sec): Set the dwell time for each step. Sequence dwell time can be set from 0 to 99 seconds.
5.8.3
Call M/T SEQ
Figure 5-31 Display Menu – Call M/T SEQ
Step: Sequence order. Cannot be changed.
Camera: Select which camera appears on the current step.
Dwell (sec): Set the dwell time for each step. Sequence dwell time can be set from 0 to 99 seconds.
81
5.9 DISK SETTING
Figure 5-32 is a screen shot of the DISK SETTING MENU. This menu is used to review and manage the
DVR’s hard drive settings.
Figure 5-32 Disk Menu
5.9.1
Disk
Disk: Select the disk number.
Health Status: Displays current status of the selected disk.
Disk Temperature: Displays current disk temperature.
Disk Size/Total: Shows total disk size.
Disk Size/Usage: Shows percentage of used disk space. If DVR is set to automatically overwrite the disk,
this option will show “Overwrite mode currently”.
Record Time (Start): Shows earliest recorded time on the hard drive.
Record Time (End): Shows latest or most current recorded time on the hard drive.
82
5.9.2
Lock/Format
Figure 5-33 Lock/Format Menu
Maximum Lock (%): User can set the maximum lock percentage of the HDD volume. After setting lock
percentage, it can be enabled/disabled in three places
1. “Camera > Basic Setting > Motion > Auto Lock”
2. “Alarm & Event > Alarm > Auto Lock”.
3. Lock or unlock the file manually in search result list
Current Lock (%): Here displays the current lock percentage of HDD volume. If locked data has reach the
maximum lock percentage, it will stop lock new data.
Unlock All: Click this button to unlock the locked part of HDD.
Delete All: Click this button to delete all the unlocked data in HDD.
Format: Click this button to format the whole HDD.
83
5.10SYSTEM SETTING
Figure 5-34 is a screen shot of the SYSTEM SETTING MENU. This menu is for setting up the system
configurations of the DVR.
Figure 5-34 System Menu – Date/Time
5.10.1 Date/Time
Date: Set current Date.
Time: Set current Time.
Date Format: Choose date format from yyyy/mm/dd, dd/mm/yyyy, and mm/dd/yyyy.
Time Format: Change time format between 12H and 24H mode.
Time Zone: Set the time zone that the DVR adjusts to when updating from the time server.
NTP: Select “Enable” or “Disable” NTP time synchronization.
NTP Server: Displays the time server address that the uses for time synchronize. To find a compatible
NTP address, please follow these steps:
a) Go to a PC that is connected to the internet.
b) Click on “START” -> “RUN” -> type “command” and press “OK”.
c) In the DOS Prompt, type “ping pool.ntp.org” to find out the IP address of an NTP Server.
NTP Update Interval: The frequency that the system automatically updates the time. Select Daily, Weekly,
or Monthly.
84
5.10.2 Daylight Saving
Figure 5-35 System Menu – Daylight Saving
Daylight Saving: Check the box to enable daylight saving time.
Start Date: Set the start date of daylight saving time.
Start Time (hh:mm): Set the time when daylight saving time begins.
Set To (hh:mm): This is what the time will change to when daylight saving begins. For most regions, this
will be one hour ahead of the “Start Time”.
End Date: Set the end date of daylight saving time.
End Time (hh:mm): Set the time when daylight saving time ends.
85
5.10.3 User
User Menu is where you can add or delete different users on the system as well as set administrator rights.
Figure 5-36 System Menu – User
Add
Click “Add” button to add a new user. Set the name (case-sensitive), password, and access level. Press
“Add” button to confirm a new user or “Cancel” to exit without making changes.
Figure 5-37 System Menu – User - Add
86
Edit
Click “Edit” button to make changes to an existing user account. Press “Save” button to save changes or
“Cancel” to exit without making changes.
Figure 5-38 System Menu – User - Edit
User Login: Check this box to activate user login. When this is disabled, no username or password is
required to access the system, and all users operate with ADMIN rights.
Auto Logoff: Check this box to automatically logoff the current user after 3 minutes of inactivity.
87
5.10.4 I/O Control
is a screen shot of the I/O Control Setting Menu. This menu is used to define the settings for
controlling the DVR through RS232 or RS485.
Figure 5-39
Figure 5-39 System Menu – I/O Control
RS232
Baud Rate: The speed used to transmit instruction or information through the RS232 port on the DVR.
Choose from the following speeds: 1200, 2400, 4800, 9600, 19200, 38400, 57600, or 115200 BPS.
Data Bit: The data bit used for transferring. This can be set to 8 or 7.
Stop Bit: This field is to set the stop bit for the RS232 connection. This can be set to 1 or 2.
Parity: This selects the transmission level of the connection. Choose either None, Odd, or Even.
RS485
PTZ Protocol: Select PTZ protocol Choose from the following protocols: Transparent, Pelco D, Pelco P,
Everfocus, or Samsung. (NOTE: all cameras must be on the same protocol)
485 ID: If more than one DVR is used through the RS485 connection, each one must be assigned a unique
ID number between 0 and 127.
Baud Rate: The speed used to transmit instruction or information through the RS485 port on the DVR.
Choose from the following speeds: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 BPS.
Data Bit: The data bit used for transferring. This can be set to 8 or 7.
Stop Bit: This field is to set the stop bit for the RS485 connection. This can be set to 1 or 2.
Parity: This selects the transmission level of the connection. Choose either None, Odd, or Even.
Control
IR Remote ID: ID used by the remote control. This can be set from 1 to 4.
88
5.10.5 Misc.
Figure 5-40 System Menu – Firmware & Misc.
Firmware
Current Firmware Version: Displays the current version.
Firmware Upgrade: Press “Upgrade” to upgrade the firmware.
NOTE: To perform a Firmware Upgrade, you will need to connect a USB flash device with
the latest version of the firmware. Do not disconnect USB device or turn off the power of
the unit during the upgrade; this can cause the system to crash.
Configurations
Load Factory Default: Click “Load” to restore all menu settings to the default values. User Account,
Network Setting, and Time are not affected.
Load From USB: Click “Load” to upload saved DVR configuration settings from a USB flash device.
Save To USB: Click “’Save” to save the current DVR configuration settings to a USB flash device.
Language: Choose which language the DVR uses. The available languages may vary based on region.
89
5.11 INFORMATION SETTING
is a screen shot of the INFORMATION SETTING MENU. This menu displays important system
information.
Figure 5-41
Figure 5-41 Information Menu – System
5.11.1 System
System
Version: Displays firmware version number.
Model: Displays DVR model number.
NTSC/PAL: Displays current video format.
Network
IP: Displays the DVR’s current IP Address.
MAC: Unique address of the DVR’s internal network card. This option cannot be changed.
DVR Name: Displays DVR name
Network ID: The ID number for the alarm network.
Status
Disk: Displays disk temperature.
Fans: Displays fan status.
90
5.11.2 Log
Figure 5-42 Information Menu – Log
Log Type:
Event: to see log sorted by event.
User: to see log sorted by user.
Operation: to see log sorted by operation.
View Log: Press “View Log” button to view the log. See Figure 5-43 for more detail.
Clear Log: Press “Clear Log” button to clear the log.
Export Log to USB: Export log data to USB.
91
Figure 5-43 Log List
Prev Page: Go to the previous page of log.
Next Page: Go to the next page of log.
Close: Close the window
92
Chapter
6
6 Networking Overview
This chapter will give you a basic instruction on how to set up the DVR for network connection. It is highly
recommended that you have a working knowledge of what a network is and how it works. This will be
helpful in completing the networking process.
6.1 Introduction to TCP/IP
TCP/IP is the group of protocols used by the Internet and most Local Area Networks (LANs) throughout the
world. In TCP/IP, every computer or other communications device that is connected to the network has a
unique IP address. By doing this you are giving your device a unique address similar to the address of your
house. An IP address is composed of four octets (numbers in the range of 0 to 255) separated by decimal
points. The IP address is used to uniquely identify a host or computer on the LAN. For example, one
computer on a network could have an IP address of 192.168.1.127.
You should never give two or more devices the same exact IP address, but the first three octets of an IP
address should be the same for all computers in the local area network. For example, if a total of 253
computers exist in a single LAN, the IP addresses could be assigned starting with 192.168.1.x, where x
represents a number in the range of 2 to 254.
6.2 Subnet Masks
Each host in a LAN has a subnet mask. The subnet mask is a set of octets that is used to determine which
LAN or class it belongs to. The number 255 is usually used to represent the network address portion of the
IP address and a zero is placed at the end to identify the host portion of the address. Basically the subnet
mask can be compared to the city you live in for your home address, but in this case you are stating the
network you belong too.
6.3 Gateway Address
Each host in a LAN has a gateway. A gateway address is composed of four octets separated by decimal
points. The gateway address is used to uniquely identify the main host or computer on the LAN that
assigns the IP addresses to your network (usually a router). This is comparable to the zip code of your
address.
93
6.4 Virtual Ports
A port number represents a "channel" or entryway for network communications. Port numbers allow
different applications on the same computer to utilize network resources without interfering with each other.
Port numbers most commonly appear in network programming, particularly socket programming.
Sometimes, though, port numbers are made visible to the casual user. For example, some websites on the
Internet use a URL like the following:
http://www.fakeaddress.com:8100/
In this example, the number 8100 refers to the port number used by the browser to connect to the web
server. The standard port number used by web sites is 80, so this number does not need to be included
with the URL (although it can be). In IP networking, port numbers can theoretically range from 0 to 65535.
Most popular network applications, though, use port numbers at the lower end of the range (such as 80 for
HTTP). Ports are similar to doors and windows of your house, with port 80 acting as the front door. If these
are not open you could not enter the house. This is the same case with ports on a network. If the ports for a
specific IP address are not open then you could not gain access to that IP address.
Note: The term port also refers to several other aspects of network technology. A port can refer to
Ethernet connection points, such as those on a hub, switch, or router. The term port is also used to
refer to a physical connection point for peripheral devices such as serial, parallel, and USB ports.
6.5 Pre-Installation
Before beginning the installation, please answer the following questions:
Do you have Hi-speed Internet?
______________
There are many types of high speed Internet available. The most common ones are T1, Cable, and
DSL (in order of speed). The DVR is not compatible with a dial-up connection.
Note: EverFocus suggests having a minimum upload speed of 256KBps. This can be
addressed by your Internet Service Provider.
What type of modem/router do you have?
______________
Modem/router model name/ #
The modem/router was either installed by your Internet service provider or purchased by you to
establish a connection to the Internet. A router assigns different internal IP addresses to local
computers; this allows multiple computers to access the Internet through the same external IP
address.
94
Do you have a static IP address?
______________
A Static IP address means you use the same IP address every time you connect to the Internet.
With a static IP address, other Internet users always know the address of your location and can
easily connect with it. This makes it much simpler to host a website, email server, or other type of
server connection. Everfocus suggests using a static IP address. If this is not available, you will
need to use a dynamic IP address. This is explained below.
Do you have a dynamic IP address?
______________
A Dynamic IP address means your IP address changes each time you connect to the Internet. We
recommend asking your Internet service provider for a Static IP address. If this is not a possibility,
you may use the DDNS feature of the DVR. DDNS stands for Dynamic Domain Name Server, a
service that provides a central database where IP information can be stored and retrieved. It allows
those using a dynamic IP address to be registered centrally so users can connect to it by name.
See Chapter 8 for details on using EverFocus DDNS.
What type of DVR are you installing?
______________
Everfocus EDR series: EDR 410, 810, 920, 1620, 1640, or 1680
Everfocus EDVR series: EDVR 4D1, 9D1, 16D1, 16D3
Everfocus ECOR series: ECOR 4, 8
6.6 What is your Network Setup?
Everfocus DVR’s can operate using one of three types of networking connections.
1. Simple One to One Connection: A simple one to one connection is the simplest type of network
connection. It uses a cross-over cable to make a direct connection from one computer to another
(or in this case a computer to a DVR).
2. Direct High Speed Modem Connection: A direct modem connection uses a standard network cable
to connect the modem directly to a computer (or in this case a modem to the DVR). This type of
connection only covers single-port modems. For a combination modem/router, use the setup
described below.
3. Router or LAN Connection – A local area network connection requires either a router or a preexisting LAN connection. This is the most common type of connection. A router allows multiple
computers and DVR’s to access each other as well as the Internet. It assigns different internal IP
addresses to the computers.
95
6.7 Simple One to One Connection
Crossover Ethernet Cable Pin outs:
The Figure below shows the pin configurations for a cross-over cable.
Connection Procedure:
The First step is to purchase or make a cross-over cable. We recommend purchasing one if you
have never made a cross-over cable. Please remember you can not use a straight through network
cable for this application
Once you have a cross-over cable plug one end into the LAN port on the back of the DVR and the
other into the network card on the back of the computer.
Log into the EverFocus DVR menu and go to the Network Setting Menu.
You must use the Static IP option for this type of connection.
96
Assign an IP of 192.168.001.003, a Subnet Mask of 255.255.255.000, and a Gateway of
192.168.001.001. You can ignore DNS Server.
The next step is to set the computer’s network settings to match those of the DVR. You will need
Administrator privileges on your Windows machine to do this.
To assign a fixed IP address in Windows 2000/XP.
97
98
99
Click on the option that says “Use the following IP address”
Assign an IP address of 192.168.1.2, a Subnet Mask of 255.255.255.0, and a Default Gateway of
192.168.1.1, then click OK.
Restart both the computer and the DVR.
To access the DVR from the computer, simply open Internet Explorer and in the address bar type:
http://192.168.1.3
100
6.8 Direct High Speed Modem Connection
Straight Through Ethernet Cable Pin outs:
The Figure below shows the pin configurations for a straight cable.
Connection Procedure:
The first step is to purchase or make a straight through cable. We recommend purchasing one if
you have never made a straight through cable. Please remember you can not use a cross-over
network cable for this application
101
Once you have a straight through cable plug one end into the LAN port on the back of the recorder
and the other into the high speed modem.
Log into the EverFocus DVR menu and go to the Network Setting Menu.
Input the Static IP address, the Subnet Mask, and the Gateway that you obtained from the internet
service provider.
Note: If you have a dynamic IP address, you can set the DVR to DHCP to automatically detect
the network settings settings. Therefore, it can use a dynamic IP address.
Exit from the DVR’s Menu to save the settings.
To access the DVR from a computer, open Internet Explorer and in the address bar type:
http:// (IP address given by your internet service provider)
Note: When using this type of connection, only one device can be connected to the modem at
a time. You will need to use a computer at a different location to test the connection.
102
6.9 Router or LAN Connection
Straight Through Ethernet Cable Pin outs:
The Figure below shows the pin configurations for a straight cable.
Connection Procedure:
The First step is to purchase or make a straight through cable. We recommend purchasing one if
you have never made a straight through cable. Please remember you can not use a cross-over
network cable for this application
103
Once you have a straight through cable plug one end into the LAN port on the back of the recorder
and the other into the router.
Log into the EverFocus DVR menu and go to the Network Setting Menu.
To let the router automatically assign an address:
Set the Network Type to DHCP. Make sure to write down the IP address and the Gateway.
Exit from the Menu to save settings.
To manually assign an address:
Go to a computer connected on the same network as the DVR.
Click on the Start button and choose Run.
o If using Windows Vista, choose Search instead.
Type “command” and click on OK.
o In Vista, you will need to double-click on the “Command Prompt” file to open it..
In the DOS prompt, type “ipconfig” and press Enter.
The network information will be displayed on a screen similar to the one below.
o In Windows Vista, look for the information that says “IP v4”.
Take the values for Subnet Mask and Default Gateway and input them into the DVR; these
values should be exactly the same in both devices. However, you should change the last
104
number of the IP address. For example, if the IP address of the computer is 192.168.2.101, the
DVR’s IP address should be 192.168.002.050.
To access the DVR from a computer simply open Internet Explorer and in the address bar type:
http:// (IP address of the DVR)
Note: The DVR’s IP address will only work at the location of the DVR. To connect from a
different location over the Internet, see below.
To set DVR for Internet Connection through router
The next step is to open ports within your router. Log into the router using a PC and open the
following ports.
o Ports to open: 80
o If your Internet service provider blocks port 80, you can change it to a different port in the
DVR’s Network Menu Setup.
o If you are using a Linksys or D-Link router, see Chapter 9 for basic support on setting up
ports. For any other router, you will need to contact the manufacturer for support.
To access the DVR from a computer simply open Internet Explorer and in the address bar type:
http:// (the IP address given by your internet service provider)
Note: If you changed to a different port other than 80, you will need to include this at the
end of the IP address
Example: http://70.20.70.20:8100
If you have a Dynamic IP address and have opened the ports, go to the next chapter to setup
DDNS.
105
Chapter
7
7 REMOTE OPERATION FROM BROWSER
7.1 CONNECTING TO PARAGON
To access the DVR from a computer, open an Internet Explorer window and in the address bar type:
Local connection: http:// (IP address from the DVR’s Network Menu)
Internet connection: http:// (IP address given by your Internet Service Provider)
The login page will appear on the screen similar to the one shown above.
Enter a user name and password to access the recorder. These can be changed in the System
section of the Main Menu.
The default user name is “admin”. The default password is “11111111”.
Click on the Login button and you will log in to the recorder’s Network Viewer.
106
7.2 BROWSER SECURITY SETTING
7.2.1
Installing ActiveX controls
When you first connect to the DVR’s IP address, you should see a screen like the one below. If you do not
see a yellow bar like the one the arrow is pointing at, your security settings may be too high. If so, go to
“Section 7.2.2 - Enabling ActiveX Controls.”
Right click on the yellow bar and select “Install ActiveX Control…”
107
Install the ePlusDVR.cab file when prompted to do so.
Once the file finishes installing, you will return to the same login page as before.
Type in the username and password and click Login to view the cameras.
Default username: admin
Default password: 11111111
108
7.2.2
Enabling ActiveX Controls
Note: This section is only necessary if you DO NOT see the yellow ActiveX bar at the top
of your browser screen when you first connect to the DVR.
At the top of the Internet Explorer Window, click on Tools, then select Internet Options.
Click the Security tab at the top of the window, then choose Custom Level near the bottom.
109
In the Security Settings window, scroll to “ActiveX controls and plug-ins”
Set the controls as follows:
“Enable”:
Allow previously unused ActiveX controls to run without prompt (Internet Explorer 7 only)
Allow scriptlets (IE7 only)
Automatic prompting for ActiveX controls
Binary and script behaviors
Display video and animation on a webpage that does not use external media player (IE7 only)
Run ActiveX controls and plug-ins
Script ActiveX controls marked safe for scripting
“Prompt”:
Download signed ActiveX controls
Download unsigned ActiveX controls
“Disable”:
Initialize and script ActiveX controls not marked as safe
Click OK and then choose Yes to change the security settings.
110
Close the window so you are back at the login screen.
Click the Refresh button to reload the page.
Install the ePlusDVR.cab file when prompted to do so.
Once the file finishes installing, you will return to the same login page as before.
Type in the user name and password and click Login to view the cameras.
Default user name: admin
Default password: 11111111.
111
7.3 REMOTE LIVE VIEW
3
2
1
1. In the main page, you will see live images in a 16-screen display (or 8 screens, depending on the
model).
2. The status of each camera is represented by different colors on the left side of the screen. Green
means normal; orange indicates a Motion; blue indicates Vloss, red indicates an alarm event. Click on
a camera number to switch that camera to full screen. Click on “4UP”, “9UP”, or “16UP” to display 4, 9,
or 16 screens. You can also press “Mic” button to transfer audio to DVR from client side if there has
microphone.
3. There are 13 icons at the top of screen. The first twelve have the same functions as the icons in the
DVR’s Main Menu. The last icon is used for PTZ control (described in the next section).
112
7.4 REMOTE PTZ CONTROL
1. Use Direction Arrows (up, down, left, right) to move the camera to the desired direction and angle.
2. In Zoom option, Click “Z+” to zoom closer or “Z-” to zoom farther away.
3. In Focus option, click “F+” to increase the focus or click “F-” to decrease the focus.
4. In Iris option, you can increase the amount of light by clicking “I+” or decrease it by clicking “I-“.
5. To program a preset position
a. Move PTZ camera to the specified position
b. Click “Preset” button
c. Click the number of the desired position (This will be displayed in the box)
d. Click “Set” button
6. Steps to jump to a preset position
a. Click “Preset” button
b. Click the number of the desired position
c. Click “Go” button
7. Shortcut steps for presets #1-9
a. Click digit 1-9 button without clicking any other buttons
8. Steps to delete a preset position
a. Click “Preset” button
b. Click the number of the desired position
c. Click “Delete” button
9. Steps to run Auto Pan
113
a. Click “Auto Pan” button
10. Pattern Operation (Pattern is the “0” Tour in Everfocus and Pelco PTZ cameras)
a. Click “Pattern” button
11. Steps to run a tour
a. Click “Tour” button
b. Click the number of the desired tour
c. Click “Go” button
12. Steps to remove a tour
a. Click “Tour” button
b. Click the number of the desired tour
c. Click “Delete” button
114
7.5 REMOTE PLAYBACK
To playback the video, press “Search” button. Select from “Time Search”, “Event Search”, or “Motion
Search”. For more details about Search setting, please refer to “4.13 Search Setting”.
“Event Search” and “Motion Search” will show maximum 400 search result items(near start time)
Playback Control Keys
Playback Control Keys:
1.
Fast rewind the video.
2.
Play Reverse the video.
3.
Stop playback.
4.
Playback the video.
5.
Fast forward the video.
6.
Pause
115
Chapter
8
8 EVERFOCUS DDNS SETUP
Setup Steps:
Step 1.
Set up the Network Menu according to the instructions detailed in the Networking chapter.
(Make sure that DNS Server 1 is set correctly or DDNS will not work)
Step 2.
Go to the website http://everfocusddns.com and check for an available name.
Note: This step is optional, as it is only used to check the availability of host name. If
the name is available, proceed to step 3 for DDNS setup.
Step 3.
In DVR’s Network Menu, go to DDNS. Choose “EverfocusDDNS” for the Server and put in
your chosen name for DVR Name.
Step 4.
Press “Submit/Update” button to confirm.
Step 5. You should now be able to connect by typing the name you created into the address bar.
Example: http://hostname.everfocusddns.com
116
Chapter
9
9 LINKSYS & D-LINK PORT FORWARDING
9.1 LINKSYS PORT FORWARDING
This section will cover a few simple configurations for the Linksys router. This chapter is only to offer some
help to the installer and end user. Please understand we DO NOT support this product and will not give
tech support on it. If you need additional technical support on this router you must call Linksys.
To access the Web-based Utility, launch a web browser and type the Router’s default IP address,
192.168.1.1, in the address bar. Then press Enter. A password request page will appear. (Non-Windows
XP users will see a similar screen.) Leave the User Name field blank. The first time you access the router,
use the default password admin. Click the OK button to continue.
The first screen that appears displays the Setup tab. This allows you to change the Router's general
settings. Change these settings as described here and click the Save Settings button to apply your
changes or Cancel Changes to cancel your changes.
Click on the “Applications & Gaming” tab.
117
Applications and Gaming allows you to set up public services on your network, such as web servers, ftp
servers, e-mail servers, or other specialized Internet applications. (Some Internet applications may not
require any forwarding) To forward a port, enter the information on each line for the criteria required.
Descriptions of each criterion are described here.
Application - In this field, enter the name you wish to give the application.
Start/End - Enter the starting number of the range under Start and the ending number under End.
Protocol - Enter the protocol used for this application, either TCP or UDP, or Both.
IP Address - For each application, enter the IP Address of the PC running the specific application.
Enable - Click the Enable checkbox to enable port forwarding for the relevant application.
When finished making changes, click the Save Settings button to apply your changes or Cancel
Changes to cancel them.
Here is an example for how the port information might look:
HTTP
CTRL
80 to 80
1600 to 1600
Both
Both
192.168.1.50
192.168.1.50
Enable
Enable
Note: If you changed port 80 in the DVR’s Network Menu, open that port instead of 80.
118
9.2 D-LINK PORT FORWARDING
This section will cover a few simple configurations for the D-Link router. This chapter is only to offer some
help to the installer and end user. Please understand we DO NOT support this product and will not give
tech support on it. If you need additional technical support on this router you must call D-Link.
Whenever you want to configure your network or the DI-624, you can access the Configuration Menu by
opening a web-browser and typing in the IP Address of the DI-264.
The DI-264 default IP Address is 192.168.0.1.
Type “admin” in the User Name field
Leave the Password blank
Click OK
The first screen that shows up is the Home Tab. This is the starting point for all the router’s settings and
functions.
119
Click Virtual Servers on the left to bring up the following screen.
Virtual Servers allows users who are connecting remotely to access services on the router’s Local Network.
The functions of each field are described below.
Virtual Server - Select Enabled or Disabled
Name - Enter the name referencing the virtual service
Private IP - The IP address of the device running the local services.
Protocol Type - The protocol used for the virtual service.
Private Port – The port number that the service uses on the LAN (Local Area Network).
Public Port - The port number that the services uses on the WAN (Wide Area Network).
Schedule – The time period the virtual server will be active.
When you have input all the information for a virtual server, click on Apply to add it to the list at the
bottom or Cancel to clear all fields.
120
Here is an example of the information for each service:
Private IP
192.168.1.50
192.168.1.50
Name
HTTP
CTRL
Protocol
Both
Both
Private Port
80
1600
Public Port
80
1600
Schedule
Enable
Enable
Note: If you changed port 80 in the DVR’s Network Menu, open that port instead of 80.
121
Chapter
10
10 TROUBLESHOOTING
If you have problems with the system, run through the following checklist to see if you can solve the
problem.
The DVR will not go into record mode.
Bring up the DVR’s Menu and check under the Camera Menu. Verify that all connected cameras
are checked as “Installed” and that Record Mode is set to “Continuous”.
Check the Disk or Information Menus and verify that the internal hard drive is being detected.
The DVR displays no picture.
Make sure the monitor is connected to either the Video Out port or the VGA port. If the monitor
has multiple inputs, make sure it is on the correct display setting.
Check that the monitor cables are good.
Verify the recorder is getting the correct amount of power.
There is no display coming from one of the channels on the DVR.
In the DVR’s Camera Menu, make sure that all cameras are checked as “Installed” and
unchecked for “Covert”.
Verify that all cameras are connected on the “Input” row on the back of the DVR.
If there is still no picture, connect a working camera to the port that has no picture. If you get an
image, the problem is coming from the camera.
I cannot connect to the recorder via the internet.
Check that the DVR’s ports are forwarded correctly in the router.
Verify that your Internet Service Provider does not block any ports.
Make sure you are using the correct IP address given by the ISP, or, if you have a Dynamic IP,
check if the number has changed.
122
Appendix
A
APPENDIX A: TIMING OF ALARM MODES
Transparent Mode
Input Event
Alarm Duration
t
t Event = t Reaction
t Event:
t reaction:
Duration of alarm input source (motion, contact, system events...)
Resulting duration for this alarm mode, related to event record, alarm outputs, OSD message,
buzzer
Timeout + Transparent Mode
Input Event
Alarm Duration
t Event
t Duration
t
t Reaction
t Event:
t Duration:
t reaction:
Duration of alarm input source (motion, contact, system events...)
Alarm duration for timeout, defined in the event setup menus
Resulting duration for this alarm mode, related to event record, alarm outputs, OSD message,
buzzer
123
Timeout Mode
Input Event
Alarm Duration
t
t Event
t Duration = t Reaction
t Event:
t Duration:
t reaction:
Duration of alarm input source (motion, contact, system events...)
Alarm duration for timeout, defined in the event setup menus
Resulting duration for this alarm mode, related to event record, alarm outputs, OSD message,
buzzer
Permanent Mode
Alarm Reset
Input Event
Alarm Duration
t
t Event
t Reaction
t Event:
t Duration:
t reaction:
Duration of alarm input source (motion, contact, system events...)
Alarm duration for timeout, defined in the event setup menus
Resulting duration for this alarm mode, related to event record, alarm outputs, OSD message,
buzzer
124
Timeout Mode: Retrigger of Alarms
t Event:
t Duration:
t reaction:
Duration of alarm input source (motion, contact, system events...)
Alarm duration for timeout, defined in the event setup menus
Resulting duration for this alarm mode, related to event record, alarm outputs, OSD message,
buzzer
Timeout+Transparent Mode: Retrigger of Alarms
t Event:
Duration of alarm input source (motion, contact, system events...)
t Duration:
t reaction:
Alarm duration for timeout, defined in the event setup menus
Resulting duration for this alarm mode, related to event record, alarm outputs, OSD message,
buzzer
125
Appendix
B
APPENDIX B: CHANGING RULE FOR
EXPRESS SETUP
Case 1:
Record Mode: Normal + Event
Record With: Recording days
DVR will Auto adjust Quality and Event frame rate to match the Recording days which user
selected:
According to resolution, event hours and assumption above, DVR will select one set of suitable quality and
event frame rate from Changing Order 1 to 8. If DVR can’t match require record days from 8 sets of
Change Order, it will just use the set of Changing Order 8.
Changing Order
1
2
3
4
5
6
7
8
Normal Frame Rate
1
1
1
1
1
1
1
1
Quality
Event Frame Rate
Superior Standard Low
30
30
Low
30
Low
15
Low
10
Low
Low
7.5
5
1
Case 2:
Record Mode: Event Only
Record With: Recording days
DVR will Auto adjust Quality and Event frame rate to match the Recording days which user need:
According to resolution, event hours and assumption above, DVR will select one set of suitable quality and
event frame rate from Changing Order 1 to 8. If DVR can’t match require record days from 8 sets, it will just
use the set of Changing Order 8.
Changing Order
Quality
Event Frame Rate
1
2
3
Superior Standard Low
30
30
4
Low
30
5
Low
15
Low
10
126
6
7
Low
7.5
8
Low
5
1
Case 3:
Record Mode: Normal + Event or Event Only
Record With: Preset Setting
DVR will apply setting in below table to all cameras according to different Preset Setting.
Preset Setting Option Camera Item
Quality
Best Quality
Standard Quality
Extended Quality
Apply value
Superior
Normal Frame Rate Max recording frame rate of DVR
Event Frame Rate
30
Quality
Standard
Normal Frame Rate Half of max recording frame rate of DVR
Event Frame Rate
30
Quality
Basic
Normal Frame Rate 1
Event Frame Rate
10
127
Headquarter Office
12F, No.79 Sec.1 Shin-Tai Wu Road,
Hsi-Chi, Taipei, Taiwan
Tel: +886-2-26982334
Fax: +886-2-26982380
Beijing office
Room 609,Technology Trade Building.
Shangdi Information Industry Base,
Haidian District,Beijing China
Tel: +86-10-62971096
Fax: +86-10-62971423
European Office
Albert-Einstein-Strasse 1,
D-46446 Emmerich, Germany
Tel: +49-2822-9394-0
Fax: +49-2822-939495
Japan Office
1809 WBG Marive East 18F,
2-6 Nakase, Mihama-ku,
Chiba city 261-7118, Japan
Tel: +81-43-212-8188
Fax: +81-43-297-0081
USA California Office
1801 Highland Ave. Unit A
Duarte, CA 91010 ,U.S.A
Tel: +1-626-844-8888
Fax: +1-626-844-8838
USA New York Office
415 Oser Ave Unit S
Hauppauge, NY 11788
Sales: +1-631-436-5070
Fax: +1-631-436-5027
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-oflife, should be disposed of separately
from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: MDHRG00220
128

advertisement

Key Features

  • Pentaplex Operation
  • Free EverFocus DDNS Service
  • Built-in DVR calculator
  • Express Setup
  • Express Copy
  • Express Playback
  • Express Search
  • Remote configuration support
  • Gigabit Ethernet interface
  • On-screen PTZ control

Frequently Answers and Questions

What type of video cable should I use with the PARAGON DVRs?
75 Ohm video cable like RG-59, RG-12 with suitable BNC plugs
What kind of audio cable should I use?
Audio coax cable and RCA plugs.
Can I connect a microphone directly to the DVR?
No, you need a microphone amplifier as the direct connection of a non-amplified microphone is not supported.
How many alarm inputs are available on the PARAGON DVRs?
PARAGON8 provides 8 alarm inputs and PARAGON16 provides 16 input.
What is the maximum cable length for the RS-485 bus?
The maximum cable length is 1200m, but for short distances, a standard CAT5 network cable can be used.

Related manuals

Download PDF

advertisement