Pacific energy PACIFIC VISTA INSERT Installation And Operating Instructions Manual

IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER
SERIAL #
SAFETY NOTICE
If this stove is not properly installed, a house
fire may result. For your safety, follow the
installation instructions. Contact local
building or fire officials about restrictions
and installation inspection requirements in
you area.
INSTALLATION
AND OPERATING
INSTRUCTIONS
TESTED and LISTED to CAN/ULC S627
and UL 1482
Meets the Environmental Protection
Agency’s July 1990 Particulate
Emission Standards
Model:
PACIFIC VISTA INSERT
Series: D
210513-24
VISTA INSERT-D
5055.3231
Contents
Safety ............................................................................................ 3
Dimensions ............................................................................................ 3
Clearances ................................................................................... 3
Masonry or Factory Built Fireplace ........................................................ 3
Maintenance Checks ................................................................... 4
Installation.................................................................................... 6
Fireplace Specifications ......................................................................... 6
Into a Masonry Fireplace ....................................................................... 6
Full Flue Liner -(Required in Canada) .................................................... 7
Direct Flue Connection - (USA only) ..................................................... 7
Into a Factory Built Fireplace ................................................................. 7
Surround Assembly and Installation ...................................................... 8
Combustion Air ...................................................................................... 9
Blower ........................................................................................... 9
Blower Operation ................................................................................... 9
Electrical Supply .................................................................................... 9
Operation.................................................................................... 10
Wood Selection.....................................................................................10
How to Test Your Wood .........................................................................10
Normal Operation .................................................................................10
Restarting After Extended or Overnight Burns......................................10
Over Firing ............................................................................................10
More Wood, More Heat.........................................................................10
Proper Draft ..........................................................................................11
Ash Removal ........................................................................................11
Disposal of Ashes .................................................................................11
Creosote ......................................................................................11
Formation and Need for Removal .........................................................11
Chimney Fires.......................................................................................11
In Case of a Chimney Fire ....................................................................11
Avoiding a Chimney Fire .......................................................................11
Maintenance ............................................................................... 12
Blower Maintenance .............................................................................12
Baffle Removal......................................................................................12
Appendix A ................................................................................. 13
Troubleshooting ....................................................................................13
Firebrick Installation Instructions ..........................................................14
Replacement Parts ...............................................................................15
Replacement Parts - Blower .................................................................16
Optional Hearth Trim Kit .......................................................................17
Label .....................................................................................................19
2
VISTA INSERT-D
210513-24
Safety
Clearances
READ ALL INSTRUCTIONS BEFORE INSTALLING
AND USING THIS APPLIANCE. FAILURE TO FOLLOW
INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY, OR EVEN DEATH.
Masonry or Factory Built Fireplace
The minimum required clearances to surrounding combustible
materials when installed into a masonry or factory built fireplace
are listed below and in Fig. #1.
We strongly recommend that smoke detectors be installed.
If smoke detectors have been previously installed, you may
notice that they are operating more frequently. This may be
due to curing of stove paint or fumes caused by accidentally
leaving the fire door open. Do not disconnect the detectors.
If necessary, relocate them to reduce their sensitivity.
Minimum Clearances to Combustibles
(Measured From Insert Body)
SAFETY NOTICE: If this stove is not properly installed, a
house fire may result. For your safety, follow the installation
directions. Consult local building or fire officials about restrictions and installation inspection requirements in your area.
The services of competent installer, certified by the Wood
Energy Technical program (WETT) - in Canada, Hearth Education Foundation (HEARTH) - in U.S.A. (or equivalent) are
strongly recommended.
Adjacent Sidewall ........................... 9 in.
Mantel ........................................... 15 in.
Top Facing .............................. 15 in.
Side Facing ............................... 9 in.
(229 mm.)
(381 mm.)
(381 mm.)
(229 mm.)
Dimensions
*Oversized Surround
Fig. # 1
Mantel or Top Facing
Side Facing
15”
t
cen
a
j
Ad all
W
ರ
Hearth
210513-24
VISTA INSERT-D
3
Maintenance Checks
Check the following parts for damage such as cracks, excessive corrosion, burned out sections and
excessive warping: (See website for descriptions and more detail)
Weekly:
- Firebrick - Visual, for cracking.
- Door Gasket - sagging, placement, damage.
Monthly
- Brick rail tabs and brick rails.
- Air riser tube in the back of the firebox.
- Back side of airwash chamber.
- Baffle locking pin.
- Boost tube cover.
When Cleaning the
Chimney System:
- Top baffle board/blanket.
- Baffle.
- Top heat shield and mounting bolt.
- Baffle Gasket.
- Brick Rails.
- Manifold.
Blower:
- The blower should be cleaned out a minimum every six months by using a vacumn on the blower
intake openings to remove any dust and debris.
- Some warping of the baffle is normal(up to 1/4” or .65cm).
- Replace if the baffle has permanent warping greater than this or has cracking or breakage.
- Please contact your Dealer if you experience any of the damage listed above. Continuing to operate
your stove with broken parts may accelerate damage to other parts and may void your warranty
4
VISTA INSERT-D
210513-24
*
Fireplace hearth requirements: (Measured without the insert)
The hearth may be flush with or raised above an adjacent combustible floor and must extend 16” in front and 8” beyond
each side of the fireplace opening.
MINIMUM FIREPLACE
OPENING AND HEARTH
DIMENSIONS
16”
23 1/2”
19 7/8”
19 7/8”
18”
Non-combustible fireplace
hearth
15”
8”
8”
2”
*
2”
**
Ember protection:
Combustible floor in front of the fireplace insert must be protected from hot embers by non-combustible material extending 16” (USA) and 18” (CANADA) to the firing side and 8” to other sides of the unit.
Consult CAN/CSA-B365 Installation Code for Solid-Fuel-Burning appliances and equipment in Canada, and N.F.P.A.
211 Standard for chimneys, fireplaces, vents and Solid-Fuel-Burning appliances in USA.
MINIMUM EMBER
PROTECTION
DIMENSIONS
18” USA
20” CANADA
Non-combustible hearth
**
16” USA
18” CANADA
Non-combustible floor
covering
2”
210513-24
VISTA INSERT-D
5
Installation
Fig. # 4
Your Insert is designed to be installed into a masonry or factory built zero-clearance fireplace. The masonry fireplace
must be built according to the requirements of the Standard
of Chimneys, Fireplaces,Vents and Solid Fuel Burning appliances, N.F.P.A. 211 (Latest Edition) or applicable National,
Provincial, State or local codes. The installation shall conform
to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning
Appliances and Equipment. The factory built zero-clearance
fireplace and its chimney must be listed per UL 127 or ULC
S610 standards.
Warning: Under no circumstances is this heater to be installed
in a makeshift or "temporary" manner.
Full Flue Liner
Rain Cap
Stainless Steel
Rigid or Flex Liner
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE.
Fireplace Specifications
Mantel or
Top Facing
Your fireplace is required to have the following minimum sizes:
WIDTH
HEIGHT
DEPTH
23-1/2" (597 mm)
19-7/8" (505 mm)
15" (381 mm)
Chimney height 15' (minimum).
A metal tag is provided and is to be fastened to the back
wall of the fireplace, if the fireplace has been modified to
accommodate the insert.
Into a Masonry Fireplace
Inspect your fireplace for cracks, loose mortar or other physical defects. If repairs are required, they should be completed
before installing your insert.
The fireplace chimney must be suitable for wood burning use.
Check for creosote build up or other obstructions, especially
if it has not been in use for some time.
The existing fireplace damper is to be locked open or removed
completely.
WARNING: Do not remove bricks or mortar from your
existing fireplace.
Exception: Masonry or steel, including the damper plate, may
be removed from the smoke shelf and adjacent damper frame
if necessary to accommodate a chimney liner, provided that
their removal will not weaken the structure of the fireplace and
chimney, and will not reduce protection for combustible materials to less than that required by the National Building Code.
The Insert must be installed in accordance with local and or
national building codes. The two methods of flue connection
that are acceptable in most areas are:
6
Full Flue Liner: where a listed stainless steel rigid or flexible
liner extends from the Insert flue collar to the top of the chimney.
Direct Flue Connection: where a listed stainless steel rigid
or flexible liner extends from the Insert flue collar to the first
chimney flue liner.
Note: A clean-out door may be required under local codes,
when a direct flue connection is used. Consult local codes.
Pacific Energy highly recommends the use of a full liner
as the safest installation and providing optimum performance. When connected to a full liner, the Insert is able
to draft correctly and will prevent problems such as difficult start-ups and smoking out the door.
VISTA INSERT-D
210513-24
Full Flue Liner -(Required in Canada)
1) Measure the chimney height from the top of the existing
flue to the floor of the hearth. This will allow extra length
of liner for flashing and rain cap.
2) Feed the stainless steel liner from top of the chimney,
through the damper area and into the fireplace cavity.
3) Attach a stove connector to the bottom of the liner.
4) Push the Insert into position inside the fireplace and attach
the connector to the stove collar. Use the rear adjusting
legs to level the Insert.
Note: For better access, the top of the casing may be removed
(Fig. #6). If it is necessary to get access to the connector pipe
through the flue outlet of the Insert, the baffle can be removed
(see Baffle Removal section page 13).
5) Measure, trim and shape a top flashing to fit the existing
chimney flue. Plan for a 1” to 1-1/2” overlap on each side.
Place flashing over top of the liner and seat firmly against
the tile.
6) Screw flashing collar to liner. Caulk gap around flashing
with RTV silicone.
7) Attach a rain cap to the end of the liner. A storm collar
may be used if desired.
Consult your local Dealer about relining your fireplace chimney.
Direct Flue Connection - (USA only)
1) Measure from the first chimney flue liner to the top of the
Insert. Allow extra length of liner to insert into flue tile.
2) Feed the stainless steel liner through the damper area
and into the first chimney flue tile. Seal around pipe.
Note: A clean-out door may be required under local codes,
when a direct flue connection is used. Consult local codes.
3) Push the Insert into position inside the fireplace and attach the connector pipe to the stove collar. Use the rear
adjusting legs to level the Insert.
Note: For better access, the top of the casing may be removed
(Fig. #6). If it is necessary to get access to the connector pipe
through the flue outlet of the Insert, the baffle can be removed
(see Baffle Removal section page 13).
Fig. # 6
210513-24
Fig. # 7
Direct Flue Connection
Mantel or
Top Facing
Chimney
Flue Liner
6" Stainless Steel
Rigid or Flex Liner
Into a Factory Built Fireplace
Your Insert may be installed into a factory built fireplace (size
permitting) with the following requirements:
1) Inspect your fireplace for damage or other physical defects.
The fireplace must be in good working condition. If in doubt
about its condition, seek professional advice. Check for
creosote build up or other obstructions inside the chimney,
especially if it has not been in use for some time. Before
installing, clean your chimney system thoroughly.
2) A full stainless steel rigid or flexible flue liner meeting type
HT requirements (2100°F) per 1777 (U.S.) or ULC S635
(Canada) must be used for both safety and performance.
The liner must be securely attached to the Insert flue collar
and the chimney top.
3) The surround must be sealed to the fireplace front or the
damper area around the chimney liner must be sealed to
prevent room air entering the chimney cavity of the fireplace.
4) The air flow within and around the fireplace must not be
altered by the installation of the Insert (i.e. no blockage of
louvers or cooling air inlet or outlet ports). This includes
the circulating air chambers in a steel fireplace or metal
heat circulator.
5) Alteration of the fireplace in any manner is not permitted
with the following exceptions:
a: external trim pieces which do not affect the operation
of the fireplace may be removed and stored on or within
the fireplace for re-assembly if the Insert is removed.
b: the chimney damper may be removed to install the liner.
VISTA INSERT-D
7
Surround Assembly and Installation
1) Lay part A, B and C face down on a flat non-marring surface.
Fasten together with 1/4" x 1/2" bolts and nuts provided
through holes at points “D” (Fig. #8 and 9).
2) Lift the surround assembly to the upright position and make
sure the front face is flat and even at the joints.
3) Engage the bottom of the pre-assembled surround onto
the unit. The surround base is notched to fit over the casing flange. (see Fig. #10) Pivot surround assembly up into
place and engage slots onto pins in the upper corners of
the casing. (see Fig. #11)
4) Push the entire appliance back until the surround assembly
is in contact with the fireplace.
Fig. # 8
Fig. # 10
D
Part A
Notch in Surround Base
D
Fig. # 11
Part C
Part B
ATTACHMENT
PIN
Fig. # 9
1/4" x 1/2" Long Bolts
Part A
D
1/4" Nuts
Part C
8
VISTA INSERT-D
210513-24
Combustion Air
Consult local building codes regarding combustion air supply.
Intake or combustion air can be supplied to the Insert in one
of two ways:
1) Outside air supply: Remove cover from ash clean out in
existing fireplace. Place a rodent screen in place of the
cover. Install the Insert as described in the "Installation"
section, making sure not to cover the opening of the air
inlet. When installation is complete, seal surround to fireplace and anywhere else air may enter. This will ensure
combustion air is drawn from outside the house and into
the 7" x 2" intake at the lower rear of the appliance.
2) Room air supply: Remove the circular knockouts from
both sides of the unit casing prior to installation (Fig. #12).
Install the Insert as described in the "Installation" section.
The Insert will now draw its air from the room through the
front.
Blower
The Insert comes equipped with a variable speed circulating
air blower. The blower system is thermostatically controlled
for automatic operation, as well manually with a convenient
bypass switch.
Blower Operation
Automatic: To operate the blower automatically, push the
rocker switch to the “0” or OFF position and set the fan speed
control to a desired setting.
This will allow the blower to turn on automatically once the
Insert has come up to operating temperature. It will also shut
the blower off after the fire has gone out and the appliance
cooled to below a useful heat output range. On and Off times
will vary with installation and location of appliance.
Manual: To manually operate the blower, push the rocker
switch to the “1” or ON position and set the fan speed control
to a desired setting. This will bypass the temperature switch
and allow full control of the blower.
Suggested settings:
- Combustion air control setting of "L" (low), operate blower
speed control on “Low”.
- Combustion air control greater than "L" (low), operate
blower speed control at desired setting.
Fig. # 12
Electrical Supply
Circulating air blower electrical rating: 115V, 60 Hz, 80 Watts.
For your protection against shock hazard, use only a properly
grounded outlet that will accept a three-pronged plug. Do not
cut or remove the grounding prong.
Consult local codes or in the absence of local codes, with the
current CSA C22.1 Canadian Electrical Code and in the USA
with the National Electrical Code, ANSI/NFPA 70 (latest edition).
Remove knockouts on
both sides
Fig. # 13
By-pass
Rocker Switch
Thermo
Switch
Blower
G (green)
Speed
Control
L1 (white)
L2 (black)
210513-24
VISTA INSERT-D
9
Operation
Wood Selection
This heater is designed to burn natural wood only. Higher
efficiency and lower emissions generally result when burning
air-dried seasoned hardwoods, as compared to softwoods or
too green or freshly cut hardwoods.
Wood should be properly air dried (seasoned) for six months
or more. Wet or undried wood will cause the fire to smoulder
and produce large amounts of creosote. Wet wood also produces very little heat and tends to go out often.
DO NOT BURN :
-Salt water wood *
-Treated wood
-Wet or green wood
-Coal/charcoal
-Garbage/Plastic *
-Solvents
* These materials contain chlorides which will rapidly
destroy metal surfaces and void warranty.
Do not burn anything but wood. Other fuel, e.g. charcoal,
can produce large amounts of carbon monoxide, a tasteless,
odourless gas that can kill. Under no circumstances should
you attempt to barbecue in this heater.
How to Test Your Wood
Add a large piece of wood to the stove when it has a good
large bed of coals. It is dry if it is burning on more than one
side within one minute. It is damp if it turns black and lights
within three minutes. If it sizzles, hisses and blackens without
igniting in five minutes it is soaked and should not be burnt.
WARNING: Do not use grates or andirons to elevate the
fuel. Burn directly on the firebricks. Replace broken or
missing bricks. Failure to do so may create a hazardous
condition.
Your PACIFIC ENERGY heater is designed for many years of
trouble free operation. Over firing the appliance will shorten
the life of the product. Failure to recitify an over firing condition
can be hazardous and may void the manufacturer’s warranty.
Lighting the Fire
WARNING: Always keep loading door closed when burning. This heater is not designed for open door burning.
Restarting After Extended or Overnight
Burns
1) Open door and rake hot embers towards the front of the
heater. Add a couple of dry, split logs on top of embers,
close door.
2) Adjust air control to "H" (high) and in just a few minutes,
logs should begin burning.
3) After wood has charred, reset air control to desired setting.
4) When burning at a slow rate for extended periods,
occasionally maintain a strong fire under supervision for
a couple of hours to relieve firebox and chimney deposits
as well as any of the deposits on the glass.
WARNING: This method is not a substitute for regular
chimney inspections and cleaning.
5) To achieve maximum firing rate, set control to "H" (Start).
Do not use this setting other than for starting or preheating
fresh fuel loads.
DO NOT OVERFIRE THIS HEATER: Attempts to achieve
heat output rates that exceed heater design specifications
can result in permanent damage to the heater and chimney.
WARNING: No alteration or modification of the combustion air control assembly is permitted. Any tampering will
void warranty and could be very
hazardous.
Over Firing
WARNING: Never use chemicals or any other volatile
liquid to start a fire.
1) Adjust air control to "H" (Start) position and open door.
2) Place crumpled newspaper in the centre of the heater and
criss-cross with several pieces of dry kindling. Add a few
small pieces of dry wood on top.
3) Ignite the paper and close the door.
4) After the fire as established itself, open the door and add
a few small logs. Close door.
5) Begin normal operation after a good coal base exists and
wood has charred.
Normal Operation
1) Set air control to desired setting. If smoke pours down
across the glass (waterfall effect), this indicates you have
shut the control down too soon or you are using too low a
setting. As every home’s heating needs vary (i.e. insulation, windows, climate, etc.), the proper setting can only
be found by trial and error and should be noted for future
burns.
10
2) To refuel, adjust air control to “H” (Start) position, and give
the fire time to brighten. Open door slowly, this will prevent
backpuffing.
3) Use wood of different shape, diameter and length (up to
18"). Load your wood from side to side and try to place
the logs so that air can flow between them. Always use
dry wood.
4) Do not load fuel to a height or in such a manner that would
be hazardous when opening the door.
5) For extended or overnight burns, unsplit logs are preferred.
Remember to char the wood completely on "H" (high) setting before adjusting air control for overnight burn.
Over firing can be caused by operating the unit with the door
open, damage to door gaskets allowing excess air to enter
the firebox, the use of kiln dried lumber, mill ends or paper
waste and prolonged or continual use on a high burn setting.
More Wood, More Heat
Seasoned wood has approximately 7500 BTU’s per pound. If
you put 10 pounds of wood in your stove for an eight hour burn
the wood will be producing 9375 BTU’s per hour. (7500 BTU x
10 lbs / 8 hrs. = 9375 BTU’s per hr.). If you put 20 lbs of wood
in your stove for an eight hour burn you will get 18,750 BTU’s
per hr. (7500 BTU x 20 lbs / 8 hrs. = 18,750 BTU’s per hr.).
This is only an example and is based on 100% efficiency. In
reality, your stove should perform in the 80% efficiency range.
Experience will give you the right settings for proper combustion and efficient burning. Remember the air inlet setting is
affected by variables such as type of wood, outside temperature, chimney size and weather conditions. With practice, you
will become proficient in operating your heater and will obtain
the performance for which it was designed.
VISTA INSERT-D
210513-24
Proper Draft
1) Draft is the force which moves air from the appliance up
through the chimney. The amount of draft in your chimney
depends on the length of the chimney, local geography,
nearby obstructions and other factors.
2) Too much draft may cause excessive temperatures in the
appliance. An uncontrollable burn or a glowing red stove
part or chimney indicates excessive draft.
3) Inadequate draft may cause backpuffing into the room and
plugging of the chimney. Smoke leaking into the room
through appliance and chimney connector joints indicates
inadequate draft.
Ash Removal
Whenever ashes get 3 to 4 inches deep in your firebox, and
when fire has burned down and cooled, remove excess ashes.
Leave an ash bed approximately 1 inch deep on the firebox
bottom to help maintain a hot charcoal bed.
In summary, a certain amount of creosote is inevitable and
must be lived with. Regular inspection and cleaning is the
solution. The use of dry, seasoned wood and ample combustion air will help to minimize the buildup.
Chimney Fires
The result of excessive creosote buildup is a chimney fire.
Chimney fires are dangerous. Chimney inside temperatures
can exceed 2000 degrees F. This causes much higher than
normal temperatures in the chimney and on its exterior surfaces thus ignition of nearby or touching combustible material
is more likely during a chimney fire. Proper clearances are
critical during such a fire.
Chimney fires are easy to detect; they usually involve one or
more of the following:
- Flames and sparks shooting out of the top of the chimney
- A roaring sound
- Vibration of the chimney
Disposal of Ashes
Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on
a non-combustible floor or on the ground, well away from all
combustible materials, pending final disposal. If the ashes
are disposed of by burial in soil or otherwise locally dispersed,
they should be retained in the closed container until all cinders
have thoroughly cooled. Other waste should not be placed
in this container!
Creosote
Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form
creosote. The creosote vapours condense in the relatively
cool chimney flue of a slow burning fire. As a result, creosote
residue accumulates on the flue lining. When ignited, this
creosote makes an extremely hot fire. The chimney connector and chimney should be inspected at least once every two
months during the heating season to determine if a creosote
buildup has occurred. If creosote has accumulated, it should
be removed to reduce the risk of a chimney fire.
1. Highest smoke densities occur when a large amount of
wood is added to a bed of hot coals and the air inlet is
closed. The heated wood generates smoke, but without
ample air, the smoke cannot burn. Smoke-free, clean
burning requires small fuel loads, two or three logs at a
time or 1/4 to 1/2 of a fuel load and leaving the air inlet
relatively wide open, especially during the first 10 to 30
minutes after each loading, when most of the smoke
generating reactions are occurring. After 30 minutes or
so, the air inlet can be turned down substantially without
excessive smoke generation. Wood coals create very little
creosote-producing smoke.
2. The cooler the surface over which wood smoke is passing, the more creosote will be condensed. Wet or green
wood contributes significantly to creosote formation as the
excess moisture that is boiled off cools the fire, making
it difficult for the tars and gasses to ignite, thus creating
dense smoke and poor combustion. This moisture-laden
smoke cools the chimney, compounding the problem by
offering the smoke the ideal place to condense.
210513-24
In Case of a Chimney Fire
1. Prepare to evacuate to ensure everyone’s safety. Have
a well understood plan of action for evacuation. Have a
place outside where everyone is to meet.
2. Close air inlets on stove.
3. Call local fire department. Have a fire extinguisher handy.
Contact your local fire authority for further information on
how to handle a chimney fire. It is most important that
you have a clearly understood plan on how to handle a
chimney fire.
4. After the chimney fire is out, the chimney must be cleaned
and checked for stress and cracking before starting another
fire. Also check combustibles around chimney and the
roof.
- The services of a competent or certified installer, (certified
by the Wood Energy Technical Training program (WETT) - in
Canada, Hearth Education Foundation (HEARTH) - in U.S.A.,)
are strongly recommended.
Avoiding a Chimney Fire
There are two ways to avoid chimney fires:
1. Do not let creosote build up to a point where a big chimney
fire is possible.
2. Do not have fires in the heater that may ignite chimney
fires. These are hot fires, such as when burning household
trash, cardboard, Christmas tree limbs, or even ordinary
fuel wood; (eg. with a full load on a hot bed of coals and
with the air inlet wide open).
VISTA INSERT-D
11
Maintenance
1. Burn wood only, dry and well seasoned. The denser or
heavier the wood when dry, the greater its heat value.
This is why hardwoods are generally preferred. Green
or wet wood will cause a rapid buildup of creosote.
If you feel it is necessary to burn wet or unseasoned
wood, do so only with the air inlet set open enough
to maintain a good strong fire and fairly high chimney
temperatures. Do not attempt to burn overnight using green or wet wood. Wet wood can cause up to
25% drop in heater output, as well as contributing
significantly to creosote buildup.
WARNING: Never use chemicals or any other volatile
liquid to start a fire. Do not burn garbage, or flammable fluids such a gasoline, naptha, or engine oil.
We strongly recommend that smoke detectors be
installed.
2. Remove ashes frequently. Embers can roll out the
door and create a fire hazard. Maintain a 1" minimum
ash base.
3. If glass becomes darkened through slow burning or
poor wood, it can readily be cleaned with any fireplace
glass cleaner when stove is cold. Never scrape with
an object that might scratch the glass. The type and
amount of deposit on the glass is a good indication
of flue pipe and chimney buildup. A light brown dusty
deposit that is easily wiped off usually indicates
good combustion and dry, well-seasoned wood and
therefore relatively clean pipes and chimney. On the
other hand, a black, greasy deposit that is difficult to
remove is a result of wet and green wood and too
slow a burning rate. This heavy deposit is building
up at least as quickly in the chimney.
Remove all particles of glass. Be careful as they are very
sharp. Install new glass complete with gasket. Replace
frame and screws.
WARNING: Do not overtighten, tighten screws very
carefully.
- Do not clean glass when hot
- Do not use abrasive cleaners on glass
6. Do not store wood within heater installation clearances,
or within the space required for fuel loading and ash
removal. Keep the area around the heater clean and
free of all loose combustibles, furniture, newspapers,
etc.
7. If gold door requires cleaning, use mild soap and water
only. Use of abrasive cleaners will void warranty.
8. Establish a routine for the fuel, wood burning and firing technique. Check daily for creosote buildup until
experience shows how often you need to be cleaning
to be safe.
9. Be aware that the hotter the fire, the less creosote
is deposited. Weekly cleaning may be necessary in
mild weather, even though monthly cleaning is usually
enough in the coldest months when burning rates are
higher.
10. Instruct all members of your family on the safe
operation of the heater. Ensure they have enough
knowledge of the entire system if they are expected
to operate it. Stress the section on chimney fires and
the importance of following the steps outlined in “In
Case of Chimney Fire”.
Blower Maintenance
The blower requires occasional cleaning to prevent buildup
of dust and hair. More frequent cleaning may be required
if conditions are dusty or pets are present. This service is
best performed by a qualified service technician.
WARNING: Only use materials supplied by the manufacturer when doing maintenance or replacements.
Baffle Removal
4. DOOR GASKET - The gasket used by Pacific Energy
requires only light pressure to seal. This will prolong
seal life. It is important that the door seal be maintained in good condition. Periodically inspect seals
and replace if necessary. Follow instructions included
in the DR31.WDGKIT kit obtainable from your nearest
Pacific Energy Dealer.
5. DOOR GLASS - Do not slam loading door or otherwise
impact glass. When closing door, make sure that no
logs protrude to impact the glass. If the glass gets
cracked or broken, it must be replaced before using
the stove. Replacement glass can be obtained from
your Dealer. The size required is8 -7/16 x 13 13/16
x 5 mm. Only ceramic glass may be used. Do not
substitute with any other type.
The baffle may be removed from the firebox to clean and
inspect the chimney liner.
DO NOT OPERATE WITH BAFFLE OR INSULATION
REMOVED.
Removal
Remove retaining pin at the back top of the firebox, just
under the baffle. Remove rail extensions in front of the baffle by turning and lifting out. Lift baffle up and pull forward
to disconnect from the supply tube. Tilt baffle sideways
to drop down and remove from firebox. Inspect gasket
between baffle and supply tube. If necessary, replace with
gasket #139.5 available from your Pacific Energy dealer.
Re-install baffle assembly by reversing order.
To remove broken glass, undo the four retaining screws
and remove the frame noting position for re-assembly.
12
VISTA INSERT-D
210513-24
Appendix A
Troubleshooting
Problem
Cause
Cure
Excessive Creosote
Buildup
1) Wood is too wet
- Use dry wood
2) Turning down air control
too soon
- Do not turn down until:
a) there is a good bed of coals
b) the wood is charred
3) Draft too low
- Improper chimney height and/or diameter
- Chimney plugged or restricted, check flue
- Provide outside air for combustion
Glass is Dirty
Low Heat Output
Won't Burn Overnight
Stove Won't Burn
1) See 1, 2, and 3 above
2) Door Gasket leakage
- Replace gasket
- Check latch
1) Wood is wet
- Use dry wood
2) Fire too small
- Build a larger fire
1) Air control set too high
- Set control lower
2) Not enough wood
- Unsplit wood is preferred for overnight burns
1) Combustion air supply
is blocked
- Check outside air supply for obstructions
(see Combustion Air section)
2) Draft too low
- Chimney plugged or restricted
Inspect and clean
- Chimney oversized or otherwise unsuitable
Consult Dealer
210513-24
VISTA INSERT-D
13
Firebrick Installation Instructions
Pacific Vista Insert
This package contains 12 full-size firebricks.
With the heater in the upright position, install firebricks as follows:
- First, install 4 firebricks against the rear wall.
- Next, install the side firebricks, 2 each side.
- Lastly, place 4 firebricks on the bottom of the heater.
ITEM
A
14
SIZE
9” X 4 1/2” X 1 1/4”
PART NUMBER
(230 mm x 115 mm x 32 mm)
VISTA INSERT-D
5096.99
210513-24
ITEM
Replacement
Parts
PART NO.
ITEM DESCRIPTION
DESCRIPTION
1......Ash Lip/Blower Assembly .....................................VIND.BLOW
2......Air Control Cover ............................................................... 2327
3......Blower Bracket................................................................... 2343
4......Glass Clamp Kit (c/w Screws) ................................SSER.1425
5......Glass Bar Kit (2 pcs.)...........................................DR16.212501
6......Rep. Glass (c/w Glass Gasket) ............................DR16.208201
7......Door Gasket Kit ................................................. DR31.WDGKIT
8......Door Casting, Arched Black ..................................... CAST.16ST
........Door Casting, Arched Gold ..................................... CAST.16GD
........Door Casting, Arched Nickel ..................................... CAST.16NI
........Door Casting, Arched Brushed Nickel .....................CAST.16BN
9......Door Handle Assembly ......................................WODC.4147C
11 ....Firebrick - 9" x 4 1/2" x 1 1/4" (12 pcs. required) ........... 5096.99
........Firebrick Set............................................................ BRIC.VISTA
12 ....Brick Rail Set ...................................................... VIST.RAILSET
15 ....Baffle..................................................................... VIST.BAFKIT
16 ....Flame Shield (c/w Bolt and Nut) .............................. VINC.2305
17 ....Baffle Gasket ...........................................................SSER.1395
18 ....Door Catch (c/w Bolt) ........................................... WODC.1461
19 ....Air Shutter Assembly ............................................... VINC.2331
PART NO.
20....Casing Bottom ................................................................... 2321
22....Surround, Regular ................................................VIND.SRNDA
23....Surround, Oversize (not shown) ..................... VINC.SURROSC
25....Casing Top, Front ............................................................... 2323
26....Casing Top, Back ............................................................... 2322
27....Casing Side, Left or Right .................................................. 2325
28....Casing Back....................................................................... 2324
* ......Standard-Size Surround Assembly, Embossed Panels ...........
36 1/2" wide x 26 1/4" high
** .....Over-Size Surround Assembly, Plain Panels ...........................
42 1/2" wide x 29 1/4" high
26
22
28
22
16
27
14
25
17
15a
13
14
27
18
13
12a
15b
2
3
12b
19
4
5
7
6
20
8
1
22
9
10
210513-24
VISTA INSERT-D
11
15
ITEM
Replacement
Parts
- Blower
PART NO.
ITEM DESCRIPTION
DESCRIPTION
1.....Ash Lip/Blower Housing ................................. VINC.2310
1a...Ashlip........................................................................2369
2.....Blower Only .........................................................5024.54
3.....Blower Bottom Cover ......................................... 2341.003
4.....Snap Disc Switch Bracket ................................. 1947.002
5.....Cordset .....................................................................5028
6.....Snap Disc Switch Wire ................................... VINC.5032
7.....Snap Disc Switch .................................................. 5027.2
PART NO.
8.....Rocker Switch Wire..................................... VINC.503221
9.....Rocker Switch ...........................................................5071
10 ...Rheostat Knob..........................................................5026
11 ...Rheostat ...................................................................5025
12 ...Rheostat Shield ........................................................2344
13 ...Cord Strain Relief .....................................................5029
.......Blower Assembly Hardware (not shown) ..... VINC.50335
1a
9
10
13
11
1
12
7
4
3
2
All parts may be ordered from your nearest Pacific Energy dealer. Contact Pacific Energy for the location of the
dealer nearest you.
16
VISTA INSERT-D
210513-24
Pacific VISTA INSERT
Optional Hearth Trim Kit
This kit contains:
1.......Hearth Trim
4...... Spring Clips
Installation:
Unpack and inspect the
hear th trim. Install the
surround assembly as
per instruction supplied
with the appliance. Attach
hearth trim to the bottom
of the surround with clips
provided. The clips are
installed up through the
Surround Side
Hearth Trim
Clips
210513-24
VISTA INSERT-D
17
18
VISTA INSERT-D
210513-24
Label
LISTED SOLID WOOD FUEL FIREPLACE INSERT / APPAREIL DU
TYPE INSERTION DE COMBUSTIBLE SOLIDE DE CHEMINÉE
CERTIFIED FOR USE IN CANADA AND U.S.A./CERTIFIE AU
CANADA ET AUX ETATS-UNIS
TESTED TO / ÉPROUVÉ SELON:
ULCS628-93 / UL1482 (2011)
MODEL / MODÈLE: PACIFIC VISTA INSERT
SERIES / SÉRIE: D
401
WN#16406
ETL# 4001507
INSTALL AND USE ONLY IN ACCORDANCE WITH PACIFIC ENERGY’S INSTALLATION AND OPERATING INSTRUCTIONS.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT CODES, RESTRICTIONS AND INSTALLATION INSPECTION IN
YOUR AREA. INSTALL AND USE ONLY IN MASONRY OR FACTORY BUILT FIREPLACE. DO NOT CONNECT THIS UNIT TO A
CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
COMPONENTS REQUIRED FOR INSTALLATION : FULL FLUE LINER CONFORMING TO CAN/ULC-S635 OR CAN/ULC-S640.
IN U.S.A. FLUE LINER CONFORMING TO UL-1777 OR DIRECT FLUE CONNECTION ASSEMBLY.
ELECTRICAL RATING 115V, 60HZ, 1.1 AMP. ROUTE POWER CORD AWAY FROM UNIT. DANGER: RISK OF ELECTRICAL
SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT.
FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT USE GRATE OR ELEVATE FIRE-BUILD WOOD FIRE DIRECTLY ON
HEARTH. REPLACE GLASS ONLY WITH CERAMIC GLASS. INSPECT AND CLEAN CHIMNEY FREQUENTLY-UNDER
CERTAIN CONDITIONS OF USE, CREOSOTE BUILDUP MAY OCCUR RAPIDLY.OPERATE ONLY WITH FEED DOOR CLOSED.
OPEN TO FEED FIRE ONLY.
C)
D)
E)
F)
TOP FACING/
REVÊTEMENT SUPÉRIEUR
SIDE FACING/
REVÊTEMENT LATÉRAL
FIRING SIDE, CANADA
FIRING SIDE, U.S.A.
EPREUVE DU FEU
OTHER SIDES
AUTRES CÔTÉS.
381 MM / 15 IN
ADJACENT SIDE WALL
MINIMUM CLEARANCE TO COMBUSTIBLES (MEASURED FROM INSERT BODY)
DÉGAGEMENT MINIMUM AUX COMBUSTIBLES
A)
ADJACENT SIDEWALL/
229 MM / 9 IN
PAROI LATÉRALE ADJACENTE
B)
MANTEL
381 MM / 15IN
B
229 MM / 9 IN
C
A
457 MM / 18 IN
406 MM / 16 IN
F
D
E
F
200 MM / 8 IN
CLEARANCE TO COMBUSTIBLE
CONSTRUCTION
INSTALLEZ ET UTILISEZ SELON LES INTRUCTIONS D’INSTALLATION ET D’OPÉRATION DU PACIFIC ENERGY. BÂTIMENT
OU POMPIERS LOCAUX DE CONTACT AU SUJET DES CODES, RESTRICTIONS ET D’INSPECTION D’INSTALLATION
DANS VOTRE SECTEUR. INSTALLEZ ET EMPLOYEZ SEULEMENT EN MAÇONNERIE OU CHEMINÉE CONSTRUITE PAR
USINE. NE RELIEZ PAS CETTE UNITÉ À UNE CONDUITE DE CHEMINÉE DE CHEMINÉE SERVANT UN AUTRE APPAREIL.
MATERIEL REQUIS POUR L INSTALLATION:PLEIN REVÊTEMENT DE CONDUITE DE CHEMINÉE CONFORMÉMENT À
CAN/ULC-S635 OR CAN/ULC-S640. ÉLECTRIQUE 115V, 60HZ, 1.1 AMP. ITINÉRAIRE POWERCORD À PARTIR D’UNITÉ.
DANGER : RISQUE DE CHOC ÉLECTRIQUE. DÉBRANCHEZ LE POUVOIR(LA PUISSANCE) AVANT L’ENTRETIEN DE
L’UNITÉ. POUR UTILISATION AVEC COMBUSTIBLE AU BOIS SEULEMENT. N’UTILISEZ PAS LA GRILLE OU N’ÉLEVEZ
PAS LE FEU EN BOIS DE FIRE-BUILD DIRECTEMENT SUR LE FOYER. REMPLACES LA VITRE AVEC UNIQUEMENT DE
LA VITRE CÉRAMIQUE. INSPECTEZ ET NETTOYEZ LA CHEMINÉE FRÉQUEMMENT-DANS CERTAINES CONDITIONS
D’UTILISATION, L’HABILLAGE DE CRÉOSOTE PEUT SE PRODUIRE RAPIDEMENT. OPÉREZ SEULEMENT AVEC LA PORTE
D’ALIMENTATION FERMÉE. OUVREZ-VOUS POUR ALIMENTER LE FEU SEULEMENT.
CAUTION
MANUFACTURED BY:
PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
2975 ALLENBY RD., DUNCAN, BC V9L 6V8
HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS.
SEE NAMEPLATE AND INSTRUCTIONS.
U.S. ENVIRONMENTAL PROTECTION AGENCY
CERTIFIED TO COMPLY WITH JULY 1990
PARTICULATE EMISSION STANDARDS
J
F
2011
DATE OF MANUFACTURE
M
A M
J
J
A
S
O
2012
2013
2014
2015
N
D
2016
MADE IN CANADA
230413
210513-24
5050.731
VISTA INSERT-D
VIND-1
19
PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
Phone: 1-250-748-1184
Web site: http://www.pacificenergy.net
2975 Allenby Rd., Duncan, B.C. V9L 6V8
Printed in Canada