Aiwa JAX-S8 Operating instructions

Aiwa JAX-S8 Operating instructions
4-247-532-21
030327AMI-NV-FM
Mini Hi-Fi Component System
JAX-S8
PRECAUTIONS
WARNING
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To prevent fire, do not cover the ventilation of the apparatus
with newspapers, table-cloths, curtains, etc. And don’t
place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled
with liquids, such as vases, on the apparatus.
En
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
“CAUTION:TO REDUCE THE RISK OF
ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.”
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
This symbol is intended to alert the user
to the presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
WARNING
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
CAUTION
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
2
On operating voltage
Before operating the system, check that the operating voltage
of your system is identical with the voltage of your local power
supply.
On safety
•The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the unit itself has been turned off.
•Unplug the system from the wall outlet (mains) if it is not to
be used for an extended period of time. To disconnect the
cord (mains lead), pull it out by the plug. Never pull the
cord itself.
•Should any solid object or liquid fall into the component,
unplug the stereo system and have the component checked
by qualified personnel before operating it any further.
•The AC power cord must be changed only at a qualified
service shop.
On placement
•Place the unit in a location with adequate ventilation to
prevent heat build-up the unit.
•Do not place the unit in an inclined position.
•Do not place the unit in locations where it is;
- Extremely hot or cold
- Dusty or dirty
- Very humid
- Vibrating
- Subject to direct sunlight.
On heat buildup
•Although the unit heats up during operation, this is not
malfunction.
•Place the unit in a location with adequate ventilation to
prevent heat build-up in the unit.
If you continuously use this unit at a loud volume, the cabinet
temperature of the top, side and bottom rises considerably.
To avoid burning yourself, do not touch the cabinet.
On operation
•If the system is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture may
condense on the lens inside the CD player. Should this occur,
the system will not operate properly. Remove the CD and
leave the system turned on for about an hour until the
moisture evaporates.
•When you move the system, take out any discs.
Notes on discs
•Discs recorded on CD-R/RW drives may not be played back
because of scratches, dirt., recording condition or the drive’s
characteristics.
•CD-R/RW discs which are not finalized at the end of
recording cannot be played back.
•Do not attach adhesive label, etc. to either side of a CD-R/
RW disc, as doing so may cause malfunction.
•Do not load an unrecorded CD-R/RW disc. The disc may be
damaged.
•Discs with non-standard shapes (e.g., heart, square, star)
cannot be played on this unit. Attempting to do so may
damage the unit. Do not use such discs.
•DVD, SACD, CD-ROM and VCD cannot be played on this
unit.
TABLE OF CONTENTS
PRECAUTIONS .................................... 2
PREPARATIONS ................................... 4
PARTS AND CONTROLS ......................... 5
ADJUSTMENTS BEFORE OPERATIONS ...... 10
CD OPERATIONS ................................ 12
MP3-CD OPERATIONS ......................... 15
TUNER OPERATIONS ........................... 17
TAPE OPERATIONS ............................. 18
SOUND ADJUSTMENTS ........................ 20
TIMER OPERATIONS ........................... 22
REFERENCE ..................................... 24
En
Music discs encoded with copyright protection
technologies
This product is designed to playback discs that conform to
the Compact Disc (CD) standard. Recently, various music
discs encoded with copyright protection technologies are
marketed by some record companies. Please be aware that
among those discs, there are some that do not conform to the
CD standard and may not be playable by this product.
If you have any questions or problems concerning your stereo
system, please consult your nearest Aiwa dealer.
3
PREPARATIONS
Connection
Plug in the AC power cord to the AC power outlet after all other
connections are made.
1 Connect the front speakers.
2 Connect the supplied antennas.
Connect the FM antenna to the FM 75 Ω terminal and
the AM antenna to the AM LOOP terminals.
Remote
Detach the battery compartment lid at the rear of the remote
and insert two R6 (size AA) batteries with correct polarity.
AM antenna
Connect the right front speaker (marked with “R”) to the
SPEAKER R terminals and place it on the right side of the
unit. Connect the left (marked with “L”) to the SPEAKER L
terminals and place it on the left side. The speaker cords
with the black stripes go to the 9 terminals.
R6(AA)
En
FM antenna
3 Connect the AC power cord to a wall outlet.
When the AC power cord is connected to a wall outlet for
the first time, DEMO appears in the display.
To deactivate the DEMO, press DISPLAY.
•Do not short-circuit the 0 and 9 speaker cord leads.
•Do not leave objects generating magnetism or objects
affected by magnetism near the speakers.
4
•Replace the batteries with new ones when the operational
distance between the remote and main unit becomes shorter.
•Remove the batteries if the unit is not going to be used for
an extended period of time.
•The remote may not operate if it is used under intense
sunlight, etc., or if its line of sight is obstructed.
PARTS AND CONTROLS
Main unit: rear
Refer to the pages indicated in parentheses for details.
1 AM LOOP, FM 75 Ω terminals (4)
Plug in the supplied AM and FM antennas here.
2 VIDEO (MD) jacks
Accepts analog sound signals from external equipment.
Connect using an optional connecting cable with RCA
phono plugs (red plug to R jack, white plug to L jack).
Refer also to the operating instructions of your equipment.
To switch function to external input, press VIDEO (MD).
Tip:
To change the displayed name for this function, turn the
unit on, then hold down VIDEO (MD) and press POWER
on the unit. Repeat the procedure to select “VIDEO” or
“MD”.
En
3 SPEAKER terminals (4)
Connect the speaker cord of the supplied front speakers
here.
4 AC power cord (4)
5
Main unit: front
Refer to the pages indicated in parentheses for details.
1 DISC CHANGE/DISC SKIP (12)
Rotates the CD trays.
7 DISC DIRECT PLAY 1-3 (12)
Selects a disc.
2 POWER 6STANDBY/ON (10)
Switches the unit on and off (standby).
The red indicator flashes when receiving a signal from
the remote.
8 zOPEN/CLOSE (12)
Opens or closes the disc compartment.
3 TAPE A/B (18)
Selects Tape function, and deck A or B.
TUNER BAND (17)
Selects Tuner function and the radio band.
VIDEO (MD) (5)
Selects the function of external equipment connected to
VIDEO (MD) jacks.
En
CD (12)
Selects CD function.
4 TREBLE/MIDDLE (20)
Enhances high or middle frequency sound.
5 CD SYNC (19)
Starts Automatic CD dubbing.
REC PAUSE/START (19)
Starts recording.
6 PHONES jack
Plug in here an optional headphones set with a mini
stereo plug (ø3.5 mm). Speaker output is canceled.
6
9 HEAVY, VOCAL, SALSA, TECHNO,
HIP HOP, MANUAL (21)
Activates a graphic equalization curve.
0 MODE (10–14, 18–20)
Selects various modes (Play mode and Tape reverse, etc.)
when used in combination with ENTER and MULTI JOG.
ENTER (10–14, 17–20, 22, 23)
Fixes the modes and the time (Play mode and Tape
reverse, etc.) when used in combination with MODE and
MULTI JOG.
! MULTI JOG (10–14, 17–20, 22, 23)
CD: skips to a previous or a succeeding track.
Tuner: selects a preset station.
Clock and Timer: sets the time.
Selects the mode and the time when used in combination
with MODE and ENTER.
@ VOLUME (10)
Adjusts the volume.
# BASS (20)
Adjusts low frequency sound.
SURROUND (21)
Switches surround on and off.
i-Bass (20)
Produces rich and clear low frequency sound.
$ DISPLAY (11, 12, 15)
Displays the time and the remaining time for CD.
When the unit is off, press DISPLAY to switch between
DEMO, Clock and ECO display modes.
ALBUM k/i (15)
Selects a previous album or a succeeding album with
MP3-CDs.
En
% rTUNING DOWN, tTUNING UP
(f , g) (12, 17, 18)
CD: searches a track in fast forward or fast reverse
playback when held down.
Tape: fast forwards or rewinds the tape.
Tuner: manually tunes down or up within the band.
aPAUSE (12, 18)
CD and Tapes: pauses playback.
dDIRECTION (12, 18)
CD and Tapes: starts playback.
sSTOP (12, 18)
CD and Tapes: stops playback.
7
Remote control
Refer to the pages indicated in parentheses for details.
Buttons with the same or similar names with the main unit
basically have the same function.
1 POWER (10)
2 1-0/10, +10 (12, 14, 15)
Selects a CD track of the specified number.
The numbered buttons take on these functions below when pressed
together with SHIFT held down:
EDIT (19)
Enters Automatic CD dubbing mode when pressed in
stop mode.
BAND (17)
Selects Tuner function and the radio band.
En
TAPE A/B (18)
Selects Tape function, and deck A or B.
SPECTRUM (10)
Changes the spectrum analyzer display.
TUNER MODE (17)
Switches between stereo or monaural FM reception.
GEQ (21)
Enters Graphic Equalizer setting mode.
TUNER MEMORY (17)
Tuner: stores the received station in to preset.
SURROUND (21)
Switches surround on and off.
8
3 r, t (12, 17, 20, 22, 23)
CD: selects a track.
Tuner: selects a preset station.
BASS, MID and TREBLE: adjusts the level.
Clock and Timer: sets the time.
4 ALBUM M/N (15)
Selects a previous album or a succeeding album.
5 PLAY MODE (13, 14, 18)
CD: selects a playback mode.
Tape: selects a reverse mode
REPEAT (13)
Enters CD repeat playback mode.
ENTER
6 CLOCK/TIMER/SET (22, 23)
Enters timer setting mode.
CLOCK/TIMER/SELECT (22, 23)
Selects timer playback, timer recording or timer off.
7 DISPLAY (11, 12, 15)
Displays the time and the remaining time for CD.
When the unit is off, press DISPLAY to switch between
DEMO, Clock and ECO display modes.
8 SHIFT
Hold down when pressing a numbered button to change
its function to that printed above the number.
e.g.)
“Press SHIFT+BAND on the remote” indicates “Hold
down SHIFT and press ‘2’ (BAND)”. Doing so makes you
be able to select Tuner function and the radio band.
9 FUNCTION
Switches the active function among CD, TAPE, TUNER
and VIDEO (MD).
0 DISC SKIP (12, 14)
Select a disc.
! c/d (12–14)
CD and Tape: starts playback.
s
CD and Tape: stops playback.
f, g (12, 17, 18)
CD: searches a track in fast forward or fast reverse
playback when held down.
Tape: fast forwards or rewinds the tape.
Tuner: manually tunes down or up within the band.
En
a (12, 18)
CD and Tape: pauses playback.
@ SLEEP (22)
Switches the sleep-timer on/off and selects the duration.
# VOLUME (+, -) (10)
Adjusts the volume.
$ SOUND (20)
Selects BASS, MID or TREBLE setting mode.
CLEAR (14)
Clears a track of the CD programed playback.
Note
The buttons not explained above (KARAOKE) do not
operate for this unit.
9
ADJUSTMENTS BEFORE OPERATIONS
POWER
STANDBY / ON
TAPE A/B,
TUNER/BAND,
VIDEO (MD),
CD
Spectrum analyzer display
POWER
MODE
You can change the spectrum analyzer display.
SPECTRUM
ENTER
MULTI JOG
1 Press MODE repeatedly until “SPECTRUM”
appears in the display when the unit is turned on
and then press ENTER within 6 seconds.
VOLUME
CLOCK/
TIMER/SET
DISPLAY
ENTER
2 Turn MULTI JOG to select one of the three
spectrum analyzer displays (PATTERN 1, 2 and
3), then press ENTER.
DISPLAY
On the remote, press SHIFT+SPECTRUM repeatedly.
SHIFT
VOLUME
+,–
En
Power
Volume
Turning the unit on
Press POWER 6STANDBY/ON (POWER on the remote).
Pressing TAPE A/B, TUNER/BAND, VIDEO (MD) or CD also
turns the unit on (Direct Play Function.)
Turn VOLUME (Press VOLUME +, - on the remote).
Adjust from 0 (minimum) to 30 and MAX (maximum).
Tip:
Volume level setting is retained during power-off standby:
If the unit is turned off with the volume set to 17 or more, it is
automatically set to 16 the next time the unit is turned on.
Turning the unit off
Press POWER 6STANDBY/ON again.
The unit goes into standby.
10
Dimmer
Setting the clock
Display mode (when off)
Adjusts the brightness of the display.
Use the remote.
1 Press MODE repeatedly until “DIMMER” appears
in the display when the unit is turned on and then
press ENTER.
1 Press CLOCK/TIMER/SET.
You can select what is displayed when the unit is off.
While the unit is off, press DISPLAY repeatedly to select one
of three display modes, DEMO, CLOCK or ECO, as explained
below:
2 Turn MULTI JOG to select one of the four dimmer
modes “DIMMER 0” to “DIMMER 3” and then
press ENTER.
“DIMMER 0” is the brightest and “DIMMER 3” is
the dimmest.
If there is no MULTI JOG or button operation within 6
seconds, the setting is canceled.
To cancel the dimmer
Repeat the above and select “DIMMER 0” in step 2 .
Go to step 3 when the time appears and the ‘hour’ flashes.
2 Press r or t repeatedly until “CLOCK”
appears in the display and then press ENTER.
3 Press r or t repeatedly to set the hour
and then press ENTER.
4 Press r or t repeatedly to set the minute
and then press ENTER.
The time display stops flashing and the clock starts from
00 seconds.
•MULTI JOG is also available in place of r or t.
To display the time
Press DISPLAY. The time will be displayed for 6 seconds.
Tip:
“AM 12:00” indicates midnight and “PM 12:00” noon.
DEMO mode
You can enjoy DEMO in the display when the unit is turned
off.
Press DISPLAY until DEMO is displayed when the unit is
turned off.
Clock mode
Displays the time while the unit is off.
Press DISPLAY until the time is displayed when the unit is
turned off.
ECO mode
Saves power while the unit is off.
Press DISPLAY until the screen goes blank when the unit is
turned off.
If “- -:- -” appears when the unit is turned off
There has been a power interruption. Re-set the clock.
11
En
CD OPERATIONS
DISC DIRECT
PLAY 1-3
DISC CHANGE/
DISC SKIP
OPEN/CLOSE
MODE
ENTER
MULTI JOG
1–0/10,
+10
DISC SKIP
CD
DISPLAY
PLAY MODE
DISPLAY
REPEAT
En
This unit plays back finalized CD-R/RW discs as well as audio
CDs.
Playback
1 Press CD and load disc(s).
Press zOPEN/CLOSE to open the disc compartment and
place one or two disc(s) with the labelled side up.
To place three discs, press DISC CHANGE/DISC SKIP so
that the trays rotate, then place the third one. Lastly, close
the compartment with zOPEN/CLOSE.
•When loading an 8-cm (3-inch) disc, place it on the
inner circle of the tray.
2 Press d(c/don the remote).
The DISC DIRECT PLAY button slowly pulses to indicate
the currently playing disc.
To stop playback
Press s.
To pause playback
Press a. Press again to resume playback.
12
To select a track
Turn MULTI JOG, or press f or g on the unit, or press
r or t on the remote repeatedly.
With the numbered buttons on the remote,
- To select track 10, press 0/10.
- To select track 20, press +10, +10 and 0/10.
- To select track 25, press +10, +10 and 5.
To search (playback in fast forward or fast reverse)
Hold down f or g. Release at the desired point.
To select a disc
Press DISC DIRECT PLAY 1-3 or DISC SKIP on the remote.
To display the remaining time of the track or the disc
Press DISPLAY repeatedly during playback.
The display changes cyclically as follows:
Track number and elapsed playing time of the current track
Track number and remaining time of the current track
Remaining time of the current disc (only for one disc
playback)
Clock display (for 6 seconds)
Presently selected sound equalization curve
To replace disc(s) during playback without
interruption
While one disc is being played back, press DISC CHANGE/
DISC SKIP so that the compartment opens, replace disc(s)
with other one(s), and press DISC CHANGE/DISC SKIP to
close the compartment.
Repeat playback
Selecting playback mode
Shuffle playback
Plays all the tracks or one track on the discs repeatedly.
You can select one or all of the discs to playback.
1 Press MODE repeatedly until “REPEAT” appears
in the display and then press ENTER.
1 In the stop mode, press MODE repeatedly until
“PLAYMODE” appears in the display and then
press ENTER.
Shuffle playback plays all the tracks on one or all the discs in
random order.
2 Turn MULTI JOG to select one of the two repeat
modes as below or “REP OFF”, and then press
ENTER.
- REP ALL:
For all the tracks on one desired disc or all discs up to
5 times. “"” lights up.
- REP 1:
For a single track only. “"1” lights up.
If there is no MULTI JOG or button operation within 6
seconds, the setting is canceled.
3 Press d(c/d on the remote).
2 Turn MULTI JOG to select one of the three play
modes and then press ENTER.
- ALL DISCS CONTINUE: Selections are played from
all discs in order.
- 1 DISC CONTINUE: Selections are played from one
disc only.
- 1 ALBUM CONTINUE: Selections are played from
one MP3 album only. (When an Audio CD is being
played, this mode is the same as 1 DISC CONTINUE.)
On the remote, press PLAY MODE repeatedly until the desired
playback mode displays.
1 In the stop mode, press MODE repeatedly until
“PLAYMODE” appears in the display and then
press ENTER.
2 Turn MULTI JOG to select one of the three play
modes and then press ENTER.
- ALL DISCS SHUFFLE: Selections are played from
all discs in random.
- 1 DISC SHUFFLE: Selections are played from one
disc in random order.
- 1 ALBUM SHUFFLE: Selections are played from
one MP3 album in random order. (When an Audio CD
is being played, this mode is the same as 1 DISC
SHUFFLE.)
On the remote, press REPEAT repeatedly until “"” or “"1”
appears and carry out step 3.
On the remote, press PLAY MODE repeatedly until the desired
playback mode displays.
To cancel repeat playback
Carry out step 1 and 2, and select “REP OFF” in step 2.
On the remote, press REPEAT repeatedly until “"” and
“"1” disappear.
To cancel shuffle playback
Carry out step 1 and 2 and select “ALL DISCS
CONTINUE”, “1 DISC CONTINUE” or “1 ALBUM
CONTINUE” in step 2.
•Although repeat playback is not possible during ALL DISCS
SHUFFLE, repeat playback during 1 DISC SHUFFLE is
possible.
13
En
DISC DIRECT
PLAY 1-3
MODE
ENTER
MULTI JOG
1–0/10,
+10
DISC SKIP
PLAY MODE
CLEAR
En
Programed playback
You can program the unit to playback selected tracks from one
or more discs in any order you specify.
1 In the stop mode, press MODE repeatedly until
“PLAYMODE” appears in the display and then
press ENTER.
2 Turn MULTI JOG to select “PROGRAM” and then
press ENTER.
4 Turn MULTI JOG to select a track and then press
ENTER.
The selected track number and the program number appear
in the display.
On the remote, press r or t and then press ENTER
or press the numbered buttons:
-To select the track 10, press 0/10.
-To select the track 20, press +10, +10 and 0/10.
-To select the track 25, press +10, +10 and 5.
“PGM” lights up.
5 Repeat step 3 and 4 to program other tracks.
If there is no MULTI JOG or button operation within 6
seconds, the setting is canceled.
6 Press d(c/don the remote).
3 Press DISC DIRECT PLAY 1-3 to select a disc.
Go to the next step when the tray stops rotating.
On the remote, press DISC SKIP.
•If you press ENTER after pressing DISC DIRECT PLAY
1-3 to select a disc, the complete disc is programmed
to play.
•If you press ENTER after you select a MP3 album (see
“To select an album” on page 15), the complete album
is programmed to play.
14
On the remote, press PLAY MODE repeatedly until “PGM”
lights up and carry out step 3 to 6.
•During programed playback, you cannot select a disc or a
track with the numbered buttons.
•If the total playback time of the program exceeds 99:59
minutes, or if a track with a track number exceeding 20 is
programed, the playing time is displayed as “- -:- -”.
•You cannot program more than 25 tracks. “FULL” is
displayed.
To clear a track
Press s (CLEAR on the remote) in stop mode. A track is
cleared from the end of the program.
To add tracks to the program
Repeat step 1 to 4 before starting playback. The tracks are
added to the end of the program.
To cancel programed playback
Carry out step 1 and 2 and select “ALL DISCS
CONTINUE”, “1 DISC CONTINUE” or “1 ALBUM
CONTINUE” in step 2.
•The program contents are retained even if the program is
canceled or after programed playback finishes. The same
program plays back if you carry out step 1, 2 and 6.
Notes on CDs
•Do not place more than one disc on one tray.
•Do not tilt the unit with discs loaded.
MP3-CD OPERATIONS
1–0/10,
+10
ALBUM
ALBUM
In this manual, CDs, CD-R discs and CD-RW discs are all
referred to as “discs”. We refer to what are called “folder” and
“file” in PC terminology as “album” and “track”.
ALBUM
ALBUM
DISPLAY
DISPLAY
Playback
This unit plays back MP3-CDs: discs recorded with MP3 tracks
(files). Basic operations for MP3-CDs are mostly the same as
those in “CD OPERATIONS”. This section explains MP3-CD
OPERATIONS where there is additional information or exceptions
to the information in “CD OPERATIONS”. Before playing an
MP3-CD, also refer to “Descriptions of MP3” for the details of
MP3.
To select an album
Press ALBUM k or i (M or N on the remote).
Descriptions of MP3
An MP3 file stores audio data compressed using MPEG1/2,
the audio layer-3 file-coding scheme.
To display the title of the album and track in the
display
Press DISPLAY during playback.
The display changes in the following order:
Track number being played and elapsed playing time
Track (file) name being played or ID3 information*
Album name* (for 2 seconds)
Clock display (for 6 seconds)
Presently selected sound equalization curve
* ID3 information and album name are not displayed if they
are not registered.
Notes on playing MP3 files
•An MP3 track must be recorded on a disc in the format
compliant with ISO 9660. Note, however, that the unit may
not play tracks in the order they were recorded.
•The maximum allowable number of tracks and albums in a
disc are as follows:
- number of tracks: 300 (including number of albums)
- number of albums: 300
•The maximum allowable depth of nested albums is 8.
•It may take 30 seconds or more before the unit can start
play of MP3 tracks, depending on the number of recorded
tracks and the complexity of the album tree.
•The unit cannot play MP3 tracks recorded using a packet
writing utility.
•The unit can play MP3 tracks having a file extension “.mp3”.
•If you play a non-MP3 track that has the “.mp3” file
extension, you may hear some noise.
To select a track on the remote
When the album has more than 99 tracks, press the numbered
buttons in the following way to select a track.
- To select the track 100, press +10, 1, 0/10 and 0/10.
- To select the track 147, press +10, 1, 4 and 7.
15
En
Notes on display indications during play
•Up to 32 characters are displayed for the title of an album or
a track. If ID3TAG version 1.X was applied to record
additional information for an MP3 track, up to 30 characters
showing track title is displayed. However, this unit does not
support ID3TAG version 2.X. Characters other than
uppercase letters (“A” to “Z”) and numerals (“0” to “9”) may
not be displayed correctly.
•The elapsed playing time may not be displayed correctly for
MP3 tracks.
En
16
Terminology
•ISO 9660
ISO stands for the “International Organization for
Standardization”. ISO 9660 determines the file structure for
the CD-ROMs. This unit can play MP3 files recorded in the
format compliant with ISO 9660.
•Nesting of folders (albums)
To organize data files stored in a PC, you can store related
files in a folder. A folder can contain other folders as well as
files. For example, folder A can contain folder B, and folder
B can contain folder C; this is called “nesting of folders”.
The maximum depth of nested folders, allowed by ISO 9660,
is 8.
•Writing utilities
There are 3 utilities used to record data on a disc.
1. DAO (Disc At Once) utility
All data to be written must be prepared in advance and
written onto a disc from the beginning to the end in one
operation. No data can be added to a disc on which data
were already written with DAO utility.
2. TAO (Track At Once) utility
Data are written onto a disc track by track. Data can be
added to a disc on which data were written with TAO utility.
3. Packet writing utility
Tracks are divided into smaller pieces while being
recorded, depending on the size of available spaces on
the disc. Data can be added to a disc on which data were
written with packet writing utility.
This unit can play MP3 discs recorded using DAO and
TAO utilities.
•ID3TAG
ID3TAG determines the data format for the text to be added
to an MP3 file, mainly used to indicate a track title or an
artist’s name, etc.
Notes on creating MP3 discs
•When converting audio data to MP3
The unit supports MP3 files with a sampling frequency from
8 kHz to 48 kHz.
The assured bit rate range for sound quality on the unit is 8
kbps to 320 kbps.
•When creating MP3 discs
Do not store more than 300 albums in a disc. Also, keep the
total number of albums and tracks 300 or less in a disc.
•To play tracks in the order they were recorded
1. Use a writing software capable of recording MP3 tracks
(files) in numerical and alphabetical order. For details on
using the software, refer to the operating instructions
supplied with the software.
2. Use only one album. (Do not create a sub-album within
an album.)
3. Include a two- or three- digit number at the beginning of
each album or track name so that the albums and tracks
are played in order.
<example of recommended names>
01XXXXX.mp3
02XXXXX.mp3
03XXXXX.mp3
04XXXXX.mp3
05XXXXX.mp3
<example of names not recommended>
1XXXXX.mp3
5XXXXX.mp3
10XXXXX.mp3
15XXXXX.mp3
20XXXXX.mp3
(Numbers at the beginning have different digit number.
The tracks will not be played in this order but played in
the order of “1”, “10”, “15”, “20” and “5”.)
TUNER OPERATIONS
Tuning in to preset stations
POWER
STANDBY / ON
TUNER BAND
BAND
ENTER
MULTI JOG
TUNER
MEMORY
TUNER
MODE
On the unit
1 Press TUNER BAND to select a band.
2 Turn MULTI JOG.
The station with the previous/succeeding preset number
is tuned in.
ENTER
SHIFT
CLEAR
Manual tuning
Preset tuning
1 Press TUNER BAND (SHIFT+BAND on the
remote) repeatedly to select a band (FM or AM.)
Preset up to 30 of your favorite stations (20 FM and 10 AM)
and tune them in directly.
2 Press f or g to tune in to a station.
Presetting stations
“TUNED” appears when a station is tuned in.
“1” lights up for FM stereo reception.
To search for a station automatically (Auto Search)
Hold down f or g.
The unit searches for a station up or down the band and stops
at reception.
To stop the search manually, press f or g.
•Auto Search may not stop at stations with weak signals.
1 Press TUNER BAND to select a band.
2 Press f or g to tune in to the desired
station.
3 Press SHIFT+TUNER MEMORY on the remote to
store the station.
The preset number, beginning from “1”, appears in the
display.
4 Press r or t on the remote to select a
preset number and press ENTER to set the
number.
5 Repeat step 1 to 4 to preset other stations.
On the remote
1 Press SHIFT+BAND to select a band.
2 Press r or t repeatedly to select the
desired station.
En
Adjustments
Antennas
Keep antennas away from metallic objects, electrical equipment
and cords.
FM antenna: Extend fully and position for the best reception.
If receiving condition is poor, connect optional outdoor antenna
to FM 75 Ω terminal. Use an adapter as required.
AM antenna: Rotate to find best reception.
To switch to monaural FM reception
Press SHIFT+TUNER MODE on the remote. With each press,
“MONO” and “1” appear alternately in the display.
Tip:
When FM stereo reception is poor, switching to monaural
reduces noise.
To switch the AM tuning interval
Hold down POWER and press ENTER on the unit. With each
press, the AM tuning interval alternates between 9 kHz/step
and 10 kHz/step.
Tip:
The default is 10 kHz/step. Change it only when using the
unit in a 9 kHz/step area. Switching AM tuning interval clears
all the preset stations.
17
TAPE OPERATIONS
DISC DIRECT
PLAY 1-3
DISC CHANGE/
DISC SKIP
TAPE A/B
CD SYNC
En
PUSH
EJECT/CLOSE
Deck A
REC PAUSE/
START
Playback
Use only TYPE I (normal) tapes.
1 Press TAPE A/B and insert the tape in either deck.
Press zPUSH EJECT/CLOSE on either side (deck A and
deck B) to open the outer cassette holder and insert the
tape in the deck.
Insert with the exposed side down and playback side facing
out from the unit. To close, push zPUSH EJECT/CLOSE
on the side where the tape is inserted.
To change the playback side
Press d in play mode.
MODE
ENTER
MULTI JOG
EDIT
PLAY MODE
PUSH
EJECT/CLOSE
SHIFT
Deck B
2 Press d (c/d on the remote).
To select a deck (deck A or deck B)
Press TAPE A/B (SHIFT+TAPE A/B on the remote) in stop mode
when tapes are loaded in both decks. The deck name (“TAPE
A” or “TAPE B”) is displayed.
To select a reverse mode
1 Press MODE repeatedly to display “REV MODE”, and
then press ENTER within 6 seconds.
2 Turn MULTI JOG within 6 seconds to select one of the three
reverse modes and then press ENTER.
- REV OFF (P): Plays only one side
- REV ]: Plays both sides repeatedly (up to 5 times)
- RELAY ON: Plays from both tapes in turn (up to 5 times)
“c” (forward) or “x” (reverse) on the display indicates
playback side.
On the remote, press PLAY MODE repeatedly until the desired
playback mode displays.
To open the inner cassette holder
The inner cassette holder opens or closes automatically when
opening or closing the outer cassette holder. If the outer
cassette holder is already open, press zPUSH EJECT/CLOSE
of the inner cassette holder to open it.
To reset the tape counter
Press s in stop mode, and the tape counter on the display is
reset to “0000”. Opening and closing the cassette holder
will also reset the tape counter.
To open or close both decks (deck A and deck B)
simultaneously
Press or push zPUSH EJECT/CLOSE on both sides of the
outer cassette holder simultaneously.
To play both tapes continuously
You can automatically playback from both tapes, one after the
other. Insert tapes in both decks. Select “RELAY ON” in
step 2 above. As soon as the playback of one deck finishes,
the other deck will start without interruption.
To stop playback
Press s.
To pause playback
Press a. Press again to resume.
To fast forward or rewind
Press f or g.
18
TAPE A/B
DISC SKIP
Notes on cassettes
•Use of 90-minute or longer tapes is not recommended since
they are extremely thin and easily deformed or damaged.
•Take up any slack in the tape with a pencil or similar tool
before use. Slack tape may jam in the mechanism.
Basic recording
Use only type I (normal) tapes. Deck B is the recording deck.
1 Insert the recordable tape in deck B.
Press zPUSH EJECT/CLOSE to open the outer cassette
holder, and insert with the exposed side down and the
side to be recorded on facing out from the unit.
Wind up the tape to the desired point if needed.
2 Press MODE repeatedly to display “REV MODE”,
and press ENTER within 6 seconds. Then turn
MULTI JOG within 6 seconds to select a reverse
mode.
3 Prepare the source.
To record CD(s), select the CD function and load disc(s).
To record a radio broadcast, tune in to the desired station.
To record a tape, insert the source tape in deck A and
select the TAPE function (deck A).
To record from connected external equipment, select the
VIDEO (MD) function and prepare the equipment.
4 Press REC PAUSE/START.
Recording is paused and ready to start.
5 Press REC PAUSE/START again to begin
recording.
If your source is CD, press d.
If your source is connected equipment, manually start
playback of the source.
•Volume or tone adjustment does not affect recording.
•“NO TAB” is displayed if you attempt to record a tape
with the tab broken off.
To stop recording
Press s.
To pause recording
Press REC PAUSE/START. Press again to resume.
To record a selected set of tracks from a CD
Program the desired tracks (see “Programmed playback”) and
then press REC PAUSE/START twice and then press d.
To erase a tape
1 Insert the tape in deck B. Set the tape to the desired point if
needed.
2 Press MODE repeatedly to display “REV MODE”, and
press ENTER within 6 seconds. Then turn MULTI JOG within
6 seconds to select a reverse mode.
3 Press TAPE A/B to select “TAPE B”.
4 Press REC PAUSE/START.
CD SYNC
You can automatically switch to recording tape from a CD.
1 Insert the recordable tape in deck B.
2 Load disc(s).
3 Select playback mode with MODE, MULTI JOG
and ENTER (see “Selecting playback mode”).
Automatic CD dubbing
You can use your unit to automatically determine the best tape
length and rearrange track order for recording from a CD. The
order of tracks is changed so that no music is split from one
side to the other side of the tape.
1 Load a disc and select it to play by pressing a
DISC CHANGE/DISK SKIP.
2 Press SHIFT+EDIT on the remote.
The unit will read the CD then display what tape length is
necessary.
•Tape lengths displayed, in minutes, are: 10, 20, 30, 40,
46, 50, 54, 60, 64, 70, 80 and 90. If a tape longer than
90 minutes is needed “OVER 90” is displayed.
3 Insert the recordable tape in deck B.
4 Press CD SYNC.
5 Press REC PAUSE/START to begin recording.
To prevent accidental erasure
Remove the plastic tab of the cassette tape with a screwdriver
or other pointed tool. To record on the tape again, cover the
detection slot with adhesive tape.
•You cannot select Repeat playback or Shuffle playback.
4 Press CD SYNC.
CD function is automatically selected.
5 Press REC PAUSE/START to start recording.
19
En
SOUND ADJUSTMENTS
HEAVY,
VOCAL,
SALSA,
TECHNO,
HIP HOP,
MANUAL
i-Bass
MODE
ENTER
MULTI JOG
TREBLE/
MIDDLE
SURROUND
Produces a rich and clear low-frequency sound besides BASS
effect.
GEQ
SURROUND
1 Press i-Bass.
“I-BA ON” is displayed and a red indicator on the iBass button lights up.
BASS
2 Turn BASS to adjust i-Bass from 1 to 4 and MAX.
i-Bass
SOUND
SHIFT
On the remote, press SOUND repeatedly until “I-BA”
appears in the display and then press r or t
repeatedly within 6 seconds.
Note
En
TREBLE and MIDDLE
BASS
TREBLE enhances high frequency for sound clarity and MIDDLE
enhances mid frequency for presence.
Emphasizes low frequencies for a powerful sound.
Turn BASS to adjust from –4 to +3 and MAX.
1 Press MODE repeatedly until “TRE/MID” displays
and press ENTER.
On the remote, press SOUND repeatedly until “BAS” appears
in the display and then press r or t repeatedly within
6 seconds.
2 Turn MULTI JOG to select “TREBLE” or
“MIDDLE” and then press ENTER.
•If the sound becomes distorted with higher levels of bass
turn the bass level down.
3 Turn TREBLE/MIDDLE to adjust the level from
–4 to +4.
On the remote, press SOUND repeatedly until “TRE” or
“MID” is displayed and then adjust the level by pressing
r or t.
•If the sound becomes distorted at higher levels of TREBLE
or MIDDLE decrease the level.
20
i-Bass must be turned on at the unit before the level can be
adjusted with the remote.
Select an i-Bass frequency
1 Press i-Bass to turn i-Bass on.
2 Press MODE repeatedly until “FREQ” is displayed and then
press ENTER.
3 Turn MULTI JOG to select one of the three frequency ranges
and then press ENTER.
- FREQ 1: Low range
- FREQ 2: Mid range
- FREQ 3: High range
After step 3, adjust the i-Bass level by turning BASS if
needed.
If there is no MULTI JOG or button operation within 6
seconds, the setting is canceled.
To cancel i-Bass
Press i-Bass to select “I-BA OFF”.
Graphic equalizer
Surround playback
Selects a sound equalization curve to match the music type.
Press HEAVY, VOCAL, SALSA, TECHNO, HIP HOP or
MANUAL.
You can playback any source with surround sound.
Press SURROUND.
On the remote, press SHIFT+GEQ and then press r or
t repeatedly within 2 seconds.
The selected equalization curve is displayed.
•MANUAL is a customized curve (see “Saving a custom
equalization curve”).
Each press turns SURROUND ON or OFF.
When SURROUND is on, “SURR” lights up in the window.
Note
Some MONO sources cannot be played back with surround
sound.
To cancel equalization
Press the selected button on the unit again. “GEQ OFF” is
displayed.
On the remote, press SHIFT+GEQ and then press r or
t repeatedly within 2 seconds until “GEQ OFF” is
displayed.
En
Saving a custom equalization curve
You can save TREBLE, MIDDLE and BASS settings to the MANUAL
button.
Hold down MANUAL until “PRESET” appears in the
display.
The customized curve is stored in MANUAL.
•If you select one of the preset curves such as HEAVY you
can customize it and save it to MANUAL.
21
TIMER OPERATIONS
POWER
STANDBY / ON
5 Press r or t to set the timer-on minute
and then press ENTER.
POWER
“OFF” appears for a moment.
ENTER
MULTI JOG
VOLUME
CLOCK/TIMER/
SELECT
CLOCK/TIMER/
SET
Deck B
CLEAR
6 Repeat step 4 and 5 to set the timer-off hour and
minute.
ENTER
7 Press r or t to select the source (CD,
TAPE and TUNER) and then press ENTER.
SLEEP
8 Press POWER to turn the unit off.
VOLUME
+,–
En
Sleep timer
Timer playback
Turns off the unit automatically after a specified time.
Turns on the unit at a specified time every day.
Make sure the clock is set correctly.
Press SLEEP on the remote repeatedly.
With each press, the timer duration changes cyclically as
follows:
“AUTO”*
“90”
“80”
---
“10”
“OFF”
The unit turns off after the selected time.
* “AUTO”: The unit turns off when the current CD or tape
finishes the playback (for up to 100 minutes).
Tip:
The display is dimmed while the sleep timer is active.
To check the remaining time until the unit turns off
Press SLEEP on the remote once. The remaining time is
displayed for 4 seconds.
To cancel the sleep timer
Press SLEEP on the remote repeatedly until “SLEEP OFF”
appears.
22
Use the remote from step 2.
1 Prepare the source.
To play CD(s), load disc(s).
To play the radio, select the band and tune in to the desired
station or tune in to a preset station (see “Tuning in to
preset stations”).
To play a tape, insert the tape and select the deck.
2 Press VOLUME +, - to set the volume level.
3 Press CLOCK/TIMER/SET to display “DAILY” and
then press ENTER.
“5” indicator lights up and “ON” appears for a moment.
If “SET CLOCK” is displayed, set the clock (see “Setting
the clock”) and carry out from this step again.
4 Press r or t to set the timer-on hour and
then press ENTER.
The unit turns on at the specified timer-on time and plays
the selected source and then turns off at the specified
timer-off time.
•To stop timer setting in step 3 to 6, press CLEAR on the
remote.
•The Timer playback will not begin unless the unit is turned
off first.
•Turning VOLUME on the unit is also available in step 2.
•MULTI JOG is also available in place of r or t.
To display the timer setting
Press CLOCK/TIMER/SELECT on the remote, then press r
or t to select “DAILY” and press ENTER. The timer-on
time, the timer-off time and the source are displayed.
To change the timer setting
Re-set the timer again.
To cancel the timer
Press CLOCK/TIMER/SELECT on the remote, then press r
or t to select “OFF” and press ENTER. “5” disappears
from the display.
Choosing a Timer function
You cannot use both Timer playback and Timer recording at
the same time. If both have been set, choose one or the other.
1 Press CLOCK/TIMER/SELECT on the remote.
“SELECT” is displayed.
2 Press r or t to select “DAILY” (Timer playback)
or “REC” (Timer recording) and press ENTER.
•To stop timer setting in step 3 to 4, press CLEAR on the
remote.
•The Timer recording will not begin unless the unit is turned
off first.
•Volume level is automatically set to 0 (minimum) when the
Timer recording is activated.
•MULTI JOG is also available in place of r or t.
Timer recording
To display the timer setting
Press CLOCK/TIMER/SELECT on the remote, then press r
or t to select “REC” and press ENTER. The timer-on
time, the timer-off time and the source (TUNER) are displayed.
Turns on the unit and makes recording once at a specified time.
Timer recording is available only for TUNER source.
Use the remote from step 3.
1 Prepare the TUNER source.
Select the band and tune in to the desired station or tune
in to a preset station (see “Tuning in to preset stations”).
2 Prepare the recording destination.
Insert the recordable tape in deck B.
3 Press CLOCK/TIMER/SET to display “DAILY”.
If “SET CLOCK” is displayed, set the clock (see “Setting
the clock”) and carry out from this step again.
4 Press r or t repeatedly until “REC”
appears in the display and then press ENTER.
“REC 5” indicator lights up and “ON” appears for a
moment.
To change the timer setting
Re-set the timer again.
Notes
•The Timer playback performs every day at the specified time
unless you cancel it. However, the Timer recording performs
only once: it automatically cancels itself when the recording
finishes.
•You cannot set the same time for timer-on time and timeroff time. “TIME NG” is displayed if you do that. In this
case, reset the time.
•You cannot select the Timer playback/recording with
CLOCK/TIMER/SELECT on the remote before setting it up.
“SET TIMER” is displayed if you do that. You must set it
up first and then select it.
•When you use the sleep timer, the timer playback/recording
will not turn on the unit until the sleep timer turns it off.
To cancel the timer
Press CLOCK/TIMER/SELECT on the remote, then press r
or t to select “OFF” and press ENTER. “REC 5”
disappears from the display.
Choosing a Timer function
You cannot use both Timer playback and Timer recording at
the same time. If both have been set, choose one or the other.
1 Press CLOCK/TIMER/SELECT on the remote.
“SELECT” is displayed.
2 Press r or t to select “DAILY” (Timer playback)
or “REC” (Timer recording) and press ENTER.
5 Carry out step 4 to step 6 described in “Timer
playback” to set the timer-on time and timer-off
time.
6 Press POWER to turn the unit off.
The unit turns on at the specified timer-on time and records
the source (TUNER) and then turns off at the specified
timer-off time.
23
En
REFERENCE
Care and maintenance
Troubleshooting
Occasional care and maintenance of the unit and the software
are needed to optimize the performance of your unit.
If your unit fails to perform properly, check the following guide
and the relevant sections of the Operating Instructions.
First, check that the AC power cord and the speakers are
connected correctly and firmly.
Should any problem persist, consult your nearest Aiwa dealer.
To clean the cabinet
Use a soft and dry cloth. If the unit surfaces are extremely
dirty, use a soft cloth lightly moistened with mild detergent
solution. Do not use strong solvents such as alcohol, benzine
or thinner.
En
To clean the tape heads
Dirty tape heads cause sound deterioration. After every 10
hours of use, clean the tape heads by using a dry-type or wettype head-cleaning cassette, sold separately. Refer to the
instructions of the cleaning cassette.
To demagnetize the tape heads
Use a sold demagnetizing cassette after every 20 to 30 hours
of use. Refer to the instructions of the demagnetizing cassette.
Care of CDs
When a CD becomes dirty, wipe it from the center out with a
cleaning cloth. However, do not use solvents. After playing a
CD, store it in its case. Do not expose a CD to direct sunlight
or heat sources.
Care of tapes
Store tapes in their cases after use. Do not leave tapes near
magnets, motors, television sets, or any source of magnetism.
Do not expose tapes to direct sunlight, or leave them in a car
parked in direct sunlight.
General
There is no sound.
•Are the speakers and AC power cord connected properly?
•Turn VOLUME clockwise and hold.
•The headphones are connected.
•Insert only the stripped portion of the speaker cord into the
SPEAKER terminal. Inserting the vinyl portion of the speaker
cord will obstruct the speaker connections.
The timer does not function.
•Set the clock correctly.
•When you used the Sleep timer, the Timer playback/
recording will not turn on the unit until the Sleep timer turns
it off.
The remote does not function.
•There is an obstacle between the remote and the unit.
•The remote is not pointing in the direction of the unit’s remote
sensor.
•The batteries have run down. Replace the batteries.
The unit shut off suddenly.
•Possibly a short circuit in the speaker terminals. Disconnect
the AC power cord from the wall outlet and reconnect the
speaker cords correctly. After a while, connect the AC power
cord to the wall outlet.
Speakers
The unit blacks out when the unit is turned off.
•ECO mode is set to on (see “ECO mode” on page 11).
Sound comes from one channel or unbalanced left
and right volume.
•Check the speaker connection and speaker placement.
Erroneous display.
•Reset the unit (see “Resetting the unit” on page 25).
There is severe hum or noise.
•A TV or VCR is placed too close to the stereo system. Move
the stereo system away from the TV or VCR.
The clock indication does not show the correct time.
•A power interruption occurred. Set the clock and timer
settings again.
24
The clock setting/radio presetting/timer is canceled.
•The AC power cord is disconnected or a power failure occurs
longer than half a day.
Redo the following:
- “Setting the clock” on page 11
- “Presetting stations” on page 17
If you have set the timer, also redo “Timer playback/
recording” on page 22 and 23.
Sound lacks bass.
•Check that the speaker’s 0 and 9 terminals are connected
correctly.
CD player
The disc compartment does not close.
•The CD is not placed properly.
The sound drops out.
•The lens is dirty. Clean it with a commercially available
blower.
The CD will not play.
•The CD is not lying flat in the disc compartment.
•The CD is dirty.
•The CD is inserted label side down.
•Moisture condensation has built up. Remove the CD and
leave the system turned on for about an hour until the
moisture evaporates.
Tape Deck
The tape does not record.
•No tape in deck B.
•The tab has been removed from the cassette tape.
•The tape has reeled to the end.
Poor tape sound.
•Use TYPE I (normal) tapes.
If the red indicator on POWER STANDBY/
ON flashes continuously,
Tuner
Rapid flashing (in approx. 0.5 sec. cycle):
Abnormal voltage flows in the unit.
•Disconnect the AC power cord from the wall outlet and then
check the voltage.
Noise is heard or poor reception.
•Check the antenna connections.
•For FM, move the FM antenna to reduce the noise.
•For AM, re-rotate the AM antenna to reduce the noise.
•Move the unit and the antennas away from other electric
appliances and cords.
Slow flashing (in approx. 2 sec. cycle):
A short circuit in the speaker terminal or some
malfunction occurs in the unit.
•Disconnect the AC power cord from the wall outlet and then
check the speaker connection. Should the problem persist,
consult your nearest Aiwa dealer.
En
The tape does not record nor play or there is decrease
in sound level.
•The heads are dirty. Clean them (see “To clean the tape
heads” on page 24).
•The record/playback heads are magnetized. Demagnetize
them (see “To demagnetize the tape heads” on page 24).
The tape does not run.
•Is the deck in pause?
The tape does not erase completely.
•The record/playback heads are magnetized. Demagnetize
them (see “To demagnetize the tape heads” on page 24).
There is excessive wow or flutter, or the sound drops
out.
•The capstans or pinch rollers are dirty. Clean them (see “To
clean the tape heads” on page 24).
Noise increases or the high frequencies are erased.
•The record/playback heads are magnetized. Demagnetize
them (see “To demagnetize the tape heads” on page 24).
Resetting the unit
If an unusual condition occurs in the display window or the
cassette deck, reset the unit as follows:
1 Press POWER to turn off the power.
If the power cannot be turned off, disconnect the AC power
cord, then plug it in again.
2 While holding down s and ENTER press POWER.
Everything stored in memory after purchase is cleared.
25
GENERAL
Specifications
MAIN UNIT CX-JS8
TUNER
FM tuning range
FM usable sensitivity (IHF)
FM antenna terminal
AM tuning range
AM usable sensitivity
AM antenna
87.5 MHz to 108 MHz
13.2 dBf
75 ohms (unbalanced)
530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1710 kHz (9 kHz step)
350 µV/m
Loop antenna
AMPLIFIER
Power output
En
Total harmonic distortion
Input
Outputs
Rated: 160 W + 160 W (6 ohms,
T.H.D. 1 %, 1 kHz)
Reference: 200 W + 200 W (6 ohms,
T.H.D. 10 %, 1 kHz)
0.08 % (100 W, 1 kHz, 6 ohms, DIN
AUDIO)
VIDEO (MD): 700 mV
SPEAKER: 6 ohms or more
PHONES: 32 ohms or more
CASSETTE DECK
Track format
Frequency response
Recording system
Heads
4 tracks, 2 channels stereo
50 Hz – 8 kHz
AC bias
Deck A: playback x 1
Deck B: recording/playback x 1,
erase x 1
CD PLAYER
Laser
D/A converter
Signal-to-noise ratio
Harmonic distortion
26
Semiconductor laser
(λ = 780 nm)
Emission duration:
continuous
1 bit dual
85 dB (1 kHz, 0 dB)
0.05 % (1 kHz, 0 dB)
Power requirements
Power consumption
Power consumption
in standby mode
Dimensions (W x H x D)
Weight
120 V AC, 60 Hz
170 W
With ECO mode on: 0.25 W
With ECO mode off: 25 W
280 x 328 x 437mm
(11 1/8 x 13 x 17 1/4 in.)
10.3 kg (22 lbs 10 oz)
FRONT SPEAKERS SX-JS8
Speaker system
Speaker units
Impedance
Dimensions (W x H x D)
Weight
2 way, bass reflex
Woofer: 120 mm (4 3/4 in.) cone x 3
Tweeter: 25 mm (1 in.) horn
6 ohms
300 x 397 x 314 mm
(11 3/4 x 15 5/8 x 12 3/8 in.)
6.2 kg (13 lbs 10 oz)
Supplied accessories
Remote commander (1)
Batteries (2)
FM antenna (1)
AM antenna (1)
Specifications and external appearance are subject to change
without notice.
COPYRIGHT
Check copyright laws relevant to recordings from discs, tuner
or tape for the country where the unit is to be used.
Licensed by BBE Sound, Inc. under USP4638258, 5510752
and 5736897.
Sony Corporation
Printed in China
http://www.aiwa.com/
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement