BH T51 5.5 Inch Triple 2RU Triple 2RU Rack Mount Monitor User Manual
Below you will find brief information for Rack-mount Monitor Triple 2RU. This triple rack-mount LCD monitor features a compact, thin, and lightweight design suitable for limited spaces and standard 19-inch rack installation. It offers FHD 1920x1080 IPS for clear viewing, a three-color tally indicator, and multiple inputs including VIDEO, AUDIO, HDMI, and 3G-SDI. You can customize buttons, load 3D-LUTs, and use advanced functions such as Center Marker, Safe Frames, and Focus Assist. Audio output is provided via a 3.5mm headphone jack.
PDF
Download
Document
Advertisement
Advertisement
5.5-inch Triple 2RU Rack-mount Monitor User Manual Foreword Thank you for purchasing our triple rack-mount monitor, please read this manual carefully before using the unit, have a nice experience. Caution 1. Please use the adapter attached in the accessory, if necessary, please use qualified adapter. 2. Please do not store or use in too cold, too hot or humid place. 3. Please keep the monitor away from the strong light while using this product to ensure the image effect and long-term use. 4. Please avoid heavy impact or drop onto the ground. 5. Please do NOT use chemical solutions to clean this product. Please wipe the monitor with a clean soft cloth to maintain the brightness of the surface. 6. No adjustable components in the monitor. Please do not take apart or repair the unit by yourself, to avoid the damage of the product. Function Feature ◆Triple rack mount LCD monitor, compact thin and lightweight design, which make it suitable for installing where the space is limited and also could be installed in the standard 19-inch rack. ◆ FHD1920x1080 IPS, view details with confidence Three-color Tally indicator, enhance team cooperation With VIDEO, AUDIO, HDMI, 3G-SDI input, suitable for a variety of signals. 1 Custom buttons, could set the custom F button function as customers operating habit. Load custom 3D-LUT, preview film look All waves accurately analysis, save budget With advanced functions like Center Marker, Safe Frames, Check Field, Focus Assist, Over Exposure, Audio Meters, Image Flip, P2P, Image Freeze, etc. 3.5mm headphone jack output 2 CONTENTS 1. Product Instructions ------------------------------ 4 1.1 Front Panel ----------------------------------------- 4 1.2 Rear Panel ------------------------------------------ 5 1.3 Power Input Way --------------------------------- 6 1.4 TALLY Indicator Connection ----------------- 7 2. 3. Menu Function Introduction ------------------- 13 4. How to Load LUT ---------------------------------5. Support Signal Formats ------------------------- 17 6. Parameters ------------------------------------------- 18 7. Trouble Shooting ----------------------------------- 19 3 1. Product Instructions 1.1 Front Panel ① / Tally indicator ② MODE Input signal selection ③ MENU Menu button, enter/confirm ④ Previous item selection/parameters increasing after enter the menu; Volume increasing adjustment when menu without display 4 ⑤ Next item selection/parameters decreasing after enter the menu; Volume decrease adjustment when menu without display Custom function shortcut button ⑥ Menu return/exit ⑦ F2 Custom function shortcut button ⑧ ON/Standby button ⑨ Earphone jack port 1.2 Rear Panel ① / DC 12V Power Input ② / 4-pin XLR DC12V power input 5 ③ ④ 3G/SDI IN (SDI serial data input) (optional) OUT(SDI serial data output) CVBS IN(Composite video broadcast signal input) OUT(Composite video broadcast signal output) ⑤ AUDIO L(Audio signal left stereo input) R(Audio signal right stereo input) ⑥ HDMI IN(High definition multimedia interface input) OUT(High definition multimedia interface output) ⑦ USB Firmware update,LUT file importing port ⑧ TALLY TALLY indicator input port 1.3 Power Input Way There are two ways of power supply to our monitor: A.The direct plug-in DC power input port supply. You can use the standard DC5.5*2.1m DC power adapter, power input polarity as shown below: B. Via 4 pin XLR interface power supply. Polarity of the 4-pin XLR power input as shown below, please note the polarity of the power input, otherwise it may damage monitor. 6 1.4 TALLY Indicator Connection 2. Operation Instruction 2.1 After connecting to the DC12V power supply, the three monitors automatically turn on 2.2 Connect the signal for each monitor separately, the screen will display the connected video image 2.3 Press “MENU” key enter to main menu, press or button to select the first level menu, press “MENU” key to confirm after selecting and enter the second level menu 2.4 Press or button to selection the function of second level menu, press “MENU” key to confirm after selecting and enter the third level menu 2.5 Press or button select open/close function or select the needed parameters, press “MENU” key to confirm after selecting. 2.6 Press key to return/exit menu 7 Remark: the buttons on each monitor are independently control 3. Menu Function Instruction Functional Assist On, Off All Waves After turning on, waveform, vector, histogram and embedded audio will be shown. On, Off Mode:RGB、YUV、Y Waveform This essential feature assists with the calibration of professional video cameras. It shows the overall brightness of the image assisting the video professional in correcting exposure. The waveform feature also checks the evenness of the lighting when lighting a chromakey or background. Waves Trans.:Off, 25%, 50%, 75% On, Off Vector shows how saturated the image is and where the pixels in the image land on the color spectrum. Histogram On, Off Mode:RGB1、RGB2、Y RGB Histogram:It can display the graphic of color tone distribution, can intuitively display the exposure status of the image, and display overlapping histograms in red, green, and blue channels Y Histogram: A quantitative tool to check the picture brightness, display different color for different brightness. 8 On, Off Focus Assist Color:(Red, Green, Blue) Peaking Level:you can adjust the peaking level after turning on(1~10) It highlights the areas that are in focus so you are able to quickly focus the camera and not miss crucial shots. On, Off Embedded Audio The Audio Level Meters provide numerical indicators and headroom levels. The audio meter is green, and will turn yellow when exceeds -20dB, and turn red when exceeds -9dB. The Audio Level Meters provide numerical indicators and headroom levels. Over Exposure On, Off Exposure Level:you can adjust the exposure level after turning on(10~100) Areas of the image over a certain threshold are filled with a striped pattern to dramatically highlight areas where too much light is falling on the image sensor. On, Off Check Field Mode:Red, Green, Blue, Mono When enabled, hue and saturation adjusted quickly and accurately On, Off False Colors An image that depicts an object in colors that differ from those a photograph (a true color image) would show. Time Code (Only under SDI signal) On, Off Mode: LTC, VITC 9 Mark On, Off Nine Grid Color: Red, Green, Blue, Black, White, Gray The area of the picture can be divided into 9 equal grids On, Off Safe Frames Mode: 80%, 85%, 90%, 93%, 96%, 2.35:1 Color: Red, Green, Blue, Black, White, Gray Center Marker On, Off Color:Red, Green, Blue, Black, White, Gray On, Off Ratio Marker Mode: 4:3、13:9、14:9、15:9、16:9、1.85:1、2.35:1 Color: Red, Green, Blue, Black, White, Gray Modified Mark:0~5 Display Scan Mode Under Scan, Over Scan Aspect Ratio Auto, 16:9, 16:10, 4:3, 5:4, 1.85:1, 2.35:1, Full Screen Provides a wide variety of aspect ratio to match different camera anamorphic lenses. On, Off Anamorphic Mode:1.33X, 1.6X, 2.0X, 2.0X MAG, User Under the User, can be customized(1.20X~2.00X) 10 Allows you to use anamorphic lenses or adapters and see the image unsqueezed, even if your camera does not de-squeeze in camera. Image Flip On, Off Mode: H Flip, V Flip, H_V Flip On, Off Zoom Mode Mode:2X、4X、9X、16X、User Under the User, can be customized(100%~200%) Image Freeze On, Off P2P On, Off Enable the filmmaker to check the image from the 1:1 signal source without scaling.This feature is essential for capturing optimum detail. User On, Off LUT After the LUT Switch is turned on, you can use the Lut (SLOG2, SLOG3, LOGC, VLOG). Lut Import:Confirm Lut Table Show the 4 built-in Lut and the custom load Lut (up to 32) Display Adjustment Backlight:0~100 Adjust the screen brightness Brightness:0~100 11 Adjust the image brightness Contrast:0~100 Adjustment of the ratio between the brightest and darkest parts of the image . When adjusting, pay attention to the sense of hierarchy in the image. If the proportion is too large or too small, it can cause the image to lose its colorful appearance. Saturation:0~100 Adjustment of color concentration Tint:0~100 Color Temp.:5600K, 6500K, 9300K, User Color Adjustment Under the User, the red, green and blue of the image can be adjusted (0~255) All Waves, Waveform, Vector, Histogram, Embedded Audio, Center Marker, Safe Frames, Nine Grid, Focus Shortcut Key Assist, False Colors, Over Exposure, Anamorphic, Image Freeze, Check Field, Zoom, Image Flip, Aspect Ratio To set the 2 shortcut custom button F1, F2 on the panel e.g.: Press MENU button enter menu , , button select User and press “MENU” button to confirm. Then select Shortcut Key and press “MENU” to confirm, select F1 and confirm to pop-up function items, then select one of them and press to confirm, the cursor will be changed to gray color after confirmed.Same setting for F2 12 System English 、 简 体 中 文 、 Español 、 Português 、 Français 、 Language Nederlands、Deutsch、日本語、繁體中文、한국어로、 русский язык OSD Time:Off, 15Sec, 30Sec, 45Sec OSD Option OSD Trans: Off, 25%, 50%, 75% No Signal: Red, Green, Blue, Black, White, Gray Volume On, Off 0~100 Scroll the wheel to select Reset and press Confirm, the Reset system back to original setting. After copying the upgrade file to the USB flash drive and Firmware Update inserting it into USB adapter cable (USB-female to mini-USB), press “MENU” wheel button Confirm to update. Don't power off during the upgrade processing 4. How to Load LUT Prepare tool: USB flash driver, mini USB to USB cable 13 4.1 USB flash driver format FAT32 4.2 Max Files Limit Maximum 32 Lut files 4.3 File requirements The LUT file format suffix should be .cube Single file not exceeded to 7.9Mb Support LUT-3D-Size 16,17,32,33,64,65 Remark: LUT file name must be English or Arabic numerals 4.4 Steps for loading 4.4.1 Make sure USB flash driver insert to the mini USB to USB can and connect with the USB interface of monitor. 4.4.2 Enter main menu --LUT--Lut Import -- press the “MENU” key Confirm to import the 3D LUT file, the monitor will auto detect the USB flash driver. If there is valid lut file in USB flash driver, the monitor will load LUT files and show “[n] name. The [n] shows the quantity number. The “name” should in LUT files’ name. If load successful, the screen will show “complete[n]”. [n] Stands for the quantity number for lut files should under 32. PS: How to clear up the imported LUTs? Insert a empty USB flash driver to the monitor, enter main menu --LUT--Lut Import -- press the “MENU” key Confirm, the imported LUTs will be clear up. 5. Support Signal Formats Signals Support signal formats Video PAL/NTSC auto recognize 14 480i /480p /576i /576p 720p(60/59.94/50/30/29/25/24/23.98) 1080i(60/59.94/50) HDMI 1080p(60/59.94/50/30/29.97/25/24/24sF/23.98/23.98sF) 4K UHD 3840×2160p (30/29.97/25/24/23.98 Hz) 4K 4096×2160p (24Hz) 720p (60/59.94/50/30/29/25/24/23.98) SDI 1080i (60/59.94/50) 1080p(60/59.94/50/30/29.97/25/24/24sF/23.98/23.98sF) 6. Parameters Panel Size 5.5″ IPS LCD×3 Resolution 1920x1080pixels Dot Pitch 0.0639(H)×0.0213(W) mm Aspect Ratio 16:9 Brightness 400 cd/m² Contrast 1000:1 Viewing Angle 80°/80°(L/R) 80°/80°(U/D) Backlight LED Input Voltage DC 9~24V Input Signal 3G-SDI (optional), HDMI, Video, Audio(L/R) Output Signal 3G-SDI (optional), HDMI, Video Audio Stereo 3.5mm headphone jack Power Consumption ≤ 25 W 15 Special Function TALLY indicator Working Temperature -20~55℃ Storage Temperature -30~65℃ Unit Size 482.6Lx88Hx34D mm Unit Weight ≈1418g 7. Trouble Shooting If there is any problem when using the unit, please try following ways to inspect and solve. Please contact us if you still can not solve it or have other problems. ● Without image display Trouble shooting ◆ Video cable off or connect Check the quality of the cable, make incorrectly ◆ Without video signal input ◆ Monitor is not be powered on ◆ Supply voltage instability ◆ self-contained power supply, polarity connect sure the correct input interface Check the signal source and output interface connect is correct or not Check whether the power is connected The power adapter plug is poor connected with the socket Reference "Power Input Way" and reconnect inversely 16 ● Image/color display abnormal Trouble shooting ◆ Video cable poor contact Change the video cable, try again ◆ Video signal interfered by Move to another environment to try external environment again ◆ Video input signal Check signal source video output, or amplitude too low change signal source and have a try. ◆ Menu color saturation Enter menu to check color, or reset to adjustment closing ◆ Check Field set in mono or black & white ◆ Image deformation factory settings Reset Check Field, back to the color Reset the image ratio ●Earphone without sound ◆ Audio cable off or connection properly ◆ Volume adjustment was closed ◆ HDMI cable poor Connected ◆ No sound after switch video signal Trouble shooting Confirm connected with the corresponding input port Reset the volume control and adjust to a proper position. Check the quality of cable, or change cable and have a try Check whether there is an AUDIO signal input in AV Mode. 17 ■ Remark: ★If there are still other problems, please contact with our related technical persons. ★If there are changes without prior notice. 18 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Triple rack-mount LCD monitor
- FHD 1920x1080 IPS display
- Three-color Tally indicator
- Multiple inputs: VIDEO, AUDIO, HDMI, 3G-SDI
- Customizable buttons
- 3D-LUT loading
- Advanced functions: Center Marker, Safe Frames
- 3.5mm headphone jack output
Frequently asked questions
The monitor can be powered via a direct plug-in DC power input port using a standard DC5.5*2.1m adapter or through a 4-pin XLR interface.
A maximum of 32 LUT files can be loaded onto the monitor.
The monitor supports PAL/NTSC auto-recognition, 480i/480p/576i/576p, 720p, 1080i, and 1080p signals via HDMI and SDI inputs. It also supports 4K UHD and 4K video signals through HDMI input.
Insert a USB flash drive with the LUT file into the monitor’s USB port, access the LUT menu, and select 'Import.'