Infinity INF PRV250 Marine Bluetooth Receiver Manual

8

Troubleshooting

*Note: In many respects, a stereo acts much like a computer and occasionally requires a

reboot. In the unlikely event of product malfunction, a reset can usually fix the issue.

A reset is accomplished by holding the Mode and Preset 1 button simultaneously until

the unit turns off.

Issue

No power

No Sound

No Reception

USB stick not reading

Cause

1. Incorrect wiring

2. Fuse is blown

3. Low battery voltage

1. Speaker connection

came loose

2. Bad speaker

3. Output blown

4. Volume too low on

media device

1. Antenna not firmly

seated in socket

1. File must be a mp3

or wma file

Solution

1. Double check wiring

2. Replace fuse

3. Check voltage of vehicle battery

with multimeter. Voltage must

be at least 11V.

1. Double check connections.

2. Replace bad speaker with known

good speaker and connect.

3. Send unit in for repair.

4. Increase volume of media device

1. Insert firmly

1. Convert format to mp3 or mwa.

While in Bluetooth mode:

No Connection 1. You are not connect

to the “INFINITY”

address on your

portable media

device.

2. Out of range

1. Choose “INFINITY”

3. The connection is

already in use.

2. Bring portable media device closer

to the receiver. Device needs to be

within 30’.

3. Ask the person who first paired to

drop out.

INFPRV250

TABLE OF CONTENTS

Product Description -------------------------------------------------------------- pg 1

Front Panel Layout -------------------------------------------------------------- pg 2

User Operation ------------------------------------------------------------------- pg 3

Radio --------------------------------------------------------------------------- pg 4

USB ----------------------------------------------------------------------------- pg 5

Bluetooth ----------------------------------------------------------------------- pg 6

Auxiliary Input ---------------------------------------------------------------- pg 6

RCA output -------------------------------------------------------------------- pg 6

Remote Option ---------------------------------------------------------------- pg 6

Installation ------------------------------------------------------------------------ pg 7

Wiring ------------------------------------------------------------------------------ pg7

Troubleshooting ------------------------------------------------------------------ pg 8

1

Product Description

This radio features state of the art Bluetooth technology allowing music to wirelessly stream from an audio source to the receiver you just purchased. Why Bluetooth? From a practical standpoint, Bluetooth enables your music device (if applicable) to be placed in a glove box, your overhead console, or even your pocket-places that are dry-without having to install a separate docking station. In addition, Bluetooth audio streaming will work with any Bluetooth enabled device, not just one brand of media. Once connected, you can use your receiver to control your media device and vice versa! Bluetooth has a range of approximately 30’, depending upon conditions, so once your boat is parked, feel free to control the stereo through your media device!

The INFPRV250 incorporates the following features:

AM/FM

Bluetooth Audio Streaming

USB input

Auxiliary input

Waterproof faceplate

50W x 4 amplifier

RF remote/wired remote option

U.S. and European tuning

Charging through USB

1 pair of RCA output

Did you know that the Infinity brand is part of Harman International Industries?

In 1958, Harman Kardon developed the world’s first stereo receiver and we are proud to bring you the world’s first Infinity marine Bluetooth receiver!

2

Installation

A mounting gasket has been added inside the package for convenience. Trace along the outside edge and this will be your cutout.

Mounting Illustration

1. Please install this unit in the place

you prefer.

Wiring Identification

2. Use the bracket and screw to fix the

unit.

Rear of the Audio Unit

(AUTO ANT)

( BACK-UP B+ )

( GROUND )

( IGNITION B+ )

( FRONT LEFT )

( REAR LEFT )

FUSE

10A

BLUE

YELLOW

BLACK

RED

WHITE

WHITE/BLACK

GREEN

GREEN/BLACK

ILL+

ORANGE

12P CONNECTOR

GRAY

GRAY/BLACK

VIOLET

VIOLET/BLACK

(REMOTE CONTROL)

(ANT JACK)

RED

WHITE (LINE OUT)

RED

WHITE (AUX)

(USB)

(FRONT RIGHT )

( REAR RIGHT )

7

6

Bluetooth Operation

Your media device must incorporate the Bluetooth option in order to stream music.

A. To pair your Bluetooth device, press the Mode button on the stereo until BT MUSIC

appears.

B. Next, go to settings on the Bluetooth device and turn the Bluetooth option to “on”.

C. Pick the “INFINITY” option on your Bluetooth enabled device (please note that

if you are prompted for a password, the code entered will be “1234”. If your stereo

does not immediately pair, press preset 3. This will allow the pairing process to

finalize. A higher pitch frequency noise will alert you to the connection/success!

The display will also read “CONN OK” (connection ok).

D. To disconnect your device, press preset 4 button. “DISCONN” will appear letting

you know you have successfully disconnected.

Auxiliary Input Mode

A. Press the Mode button until “AUX” appears on the LCD screen.

B. The use of auxiliary mode allows you to play the portable music device through

the headphone jack.

RCA output

Description: The use of RCA outputs allow an amplifier or subwoofer to be hooked up.

Remote Option

A. RF remote option.

In order to take advantage of the remote option, a transmitter and receiver must be

purchased (together part #, MILRF9 UART). Once plugged in the RF remote dongle,

the RF remote will allow for wireless remote control possibility.

B. Wired remote.

Proprietary wired remotes may also be used with this Infinity unit. Part # JBLMC20

may be purchased.

Front Panel Layout

1 2 3 4

5

6

VOL

VOL

MODE

SEL BAND A.PS

PRV-250

TUN

TUN

1 2 INT 3 RPT 4 RDM

7

8

MODE

SEL

BAND

A.PS

1

9 10 11 12

Power On/Off button.

Short push for the first time to turn the unit on.

Press and hold for more than 2 seconds to turn the unit off.

Mode Function.

Switches amongst Radio, Bluetooth, USB and Auxiliary mode.

SEL stands for SELECT.

Band Function. Switches amongst AM and FM bands.

Auto Preset and Presets Scan.

Preset 1 while in Radio mode;

Play/Pause while in USB and BT Music mode.

3

Front Panel Layout

2 INT

3 RPT

4 RDM

VOL

VOL

TUN

TUN

Preset 2 while in Radio mode; Introduction while in USB mode.

Preset 3 while in Radio mode; Repeat while in USB mode.

Preset 4 while in Radio mode; Random while in USB mode.

Volume Increase

Volume Decrease

Track Up / Tune Up / Fast Forward

Track Down / Tune Down / Reverse

Radio Operation

A. SEL button

1. Pressing this button in succession results in the following menu options: volume,

bass, treble, balance, fader, display. Press the VOL or VOL to adjust the options.

2. A long press of the SEL button initially followed by a short press results in the

following menu options: Initial Volume, Area Frequency, Beep, Time, Loud, BT

Volume. Press the VOL or VOL to adjust the options.

a. Initial Volume. Refers to the loudness level upon start of the receiver.

b. Frequency. Choose between U.S. And European.

c. Beep. Choose between Beep ON, Beep 2ND, Beep OFF. Beep ON will result in

the beep sound at the press of every button; Beep 2ND will result in the beep

sound once the button is long pressed; Beep OFF results i the beep sound off

completely.

d. Clock. VOL results in the minutes being changed; VOL results in the hour

being changed.

e. LOUD. Chose between Loud ON or OFF.

f. BT Volume. Adjust to change the initial Bluetooth volume.

4

Radio Operation

B. Pres BAND to access FM and AM. There are three FM bands and AM band, each band

containing four presets.

C. A.PS button. Short push to scan preset stations in current band. Long push to

automatically preset four stations into the current band.

D. Presets. Upon finding a desirable station, hold either the preset 1, 2, 3, or 4 down for

2 seconds to store.

E. Tuning. A short press of the TUN or TUN button results in a search of the station

of the station of next sufficient signal strength. A long press results in manual tuning

mode, allowing you to search one odd digit frequency at a time.

USB Operation

Note: USB slot is for USB sticks only. For play of other brands of media, please use the auxiliary input or if applicable, utilize Bluetooth mode.

A. Insert a USB stick into the USB slot. *Songs must be of the mp3 or wma format.*

B. Press 1 to pause the track. Press 1 button again to resume play.

C. A short press of the TUN or TUN buttons will track up or track down

respectively. A long press on the TUN or TUN will fast forward and rewind

the current track respectively.

D. INT button (INT stands for Introduction). A press of this button will result in

playing the first 10 seconds of each track located on the USB stick. Pressing the

button again will allow the unit to resume on the current track and correspondingly

stops the Introduction process.

E. RPT button (RPT stands for Repeat). Pressing this button will result in repetitive

playing of the current track. Pressing the RPT button again will stop the repeat

process. A long push plays the tracks in the current folder repeatedly.

F. RDM (RDM stands for Random). Pressing this button will result in random playing

of the USB stick files. Pressing this button again will stop the random playing

process.

H. APS (APS stands for Autopreset)

1. The first press of this button will result in track search mode. Press VOL or

VOL to your desired track and push SEL to confirm.

2. The second push will result in song name search mode. Press VOL or VOL

to the desired track and push SEL to confirm.

3. The third push will result in directory name. Press VOL or VOL to scan

Directory name and at desired directory push SEL to confirm.

5