3M Scotchcast 3832 Buried Service Wire Splice Encapsulation Kit Instructions
Below you will find brief information for Buried Service Wire Splice Encapsulation Kit Scotchcast 3832. The Scotchcast 3832 is a kit for encapsulating splices in buried service wires. The kit includes a barrel, sleeve, end caps, and a mixing bag of compound. The compound is used to seal the splice and protect it from the elements. The kit is easy to use and can be installed in minutes. You can use this kit for repairing or extending your electrical wiring in a variety of applications.
advertisement
▼
Scroll to page 2
3M™ Scotchcast™ Buried Service Wire Splice Encapsulation Kit 3832 For up to 5-pair buried service wires Instructions 1. Snipendcapportstofitsnugoncables(oneporton eachendcapforin-linesplice,twoportsonlowerend capforbuttsplice,etc.). 2. Slideendcap(s)overcableendsandpushdownoutof theway. 5. AttachsplitbolttowireshieldsperFigure2.Tighten securely. 6. SpliceconductorsperFigure2. 3. Forinlinesplice,placebarrelandsleeveovereither cableandslidedownoutoftheway. 4. PrepareservicewiresperFigure1.Scuffandclean surfacesthatwillcomeincontactwithcompound.Use of3M™Scotchcast™ServiceWireCleaningKit4415 isrecommended. Inline Configuration Inline: 3 3/4" (95 mm) Butt: 2 1/2" (64 mm) 1/8" (3 mm) Core wrap 3/4" (19 mm) Shield 3" (76 mm) Scuff and clean outer sheath Butt Configuration Figure 2 7. Centerbarrelandsleeveoversplice.Slideendcaps (lowerendcapforbuttsplice)ontobarrelseatingthem firmlyintoplace. 8. Forinlinesplice,levelbarrelwithopeningontop. 9. Forbuttsplice,closebarrelopeningwithsleeve. Figure 1 January 2011 78-0013-3885-0-A 3 10. Mix Compound: Warm closed mixing bag to 16°C (60°F) or more before mixing. Break center barrier by grasping sides of bag and rolling thumbs through barrier. 12. Close Barrel: By rotating sleeve for inline splice, with upper end cap for butt splice. Note Figure 3. Inline Configuration Butt Configuration Figure 3 Thoroughly mix by squeezing compound back and forth 30 to 40 times. Strip compound from corners while mixing. 13. Closure may be placed immediately after completion of filling operation. mCAUTION Vapor and liquid may cause sensitization. Contains isocyanate. May be irritating to the eyes. Avoid skin and eye contact. Avoid repeated and prolonged breathing of vapor. Use only in well ventilated areas. mFIRST AID Inhalation - provide fresh air. In case of eye contact flush eyes with plenty of water for 10 minutes and get medical attention. If ingested - do not induce vomiting. Get medical attention. Wash with soap and water in case of skin contact. 11. Snip off corner of closed mixing bag and pour compound into barrel (through opening for inline splice, through upper end for butt splice) until completely full. 3M and Scotchcast are trademarks of 3M Company. Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Communication Markets Division 6801 River Place Blvd. Austin, TX 78726-9000 1-800-426-8688 www.3MTelecommunications.com Please Recycle. Printed in USA. © 3M 2011. All Rights Reserved. 78-0013-3885-0-A
advertisement
Key Features
- For up to 5-pair buried service wires
- Inline and Butt splice configurations
- Easy to use, install in minutes
- Provides a durable and watertight seal
- Protects splices from the elements
- Made of high-quality materials
Frequently Answers and Questions
What is the Scotchcast 3832 kit used for?
The Scotchcast 3832 kit is used for encapsulating splices in buried service wires. The kit includes a barrel, sleeve, end caps, and a mixing bag of compound. The compound is used to seal the splice and protect it from the elements.
How do I use the Scotchcast 3832 kit?
The instructions for using the Scotchcast 3832 kit are provided in the document. Make sure to follow safety precautions and wear appropriate protective gear while using the kit.
Related manuals
Download
PDF
advertisement