Jablotron JA-80N Owner Manual
Jablotron JA-80N
The Jablotron JA-80N is an outdoor RFID card reader designed to control access (door lock) or to control a security system. It connects to the Oasis control panel via a WJ-80 interface or to an AS-80 unit as part of a stand-alone access system.
The reader is weatherproof (IP65) and can be used outdoors. It has a mechanical endurance of IK08, which means it can withstand impacts of up to 5 joules.
The reader uses Wiegand 26b format to send data to the control panel. It can be configured to operate in different modes, including:
- Card reader mode: The reader can be used to control access to a door or other secure area. When a valid RFID card is presented to the reader, the door will unlock or the security system will be disarmed.
advertisement
The JA-80N outdoor RFID card reader
The JA-80N is a component of Jablotron’s Oasis
80 alarm system. It is designed to control access
(door lock) or to control a security system and connects to the Oasis control panel via a WJ-80 interface.
Alternatively it can be connected to an AS-80 unit as a part of a stand-alone access system.
The keypad sends data in Wiegand 26b format.
Installation
Installation shall only be undertaken by technicians holding a certificate issued by an authorized distributor. It is usually placed near an entrance door
(equipped with an electronic lock). The reader can be used outdoors (conforms to IP-65).
1. Open the rear cover by unscrewing the screw
2. Prepare a hole in the wall for the reader cable to pass through, where the reader will be located.
3. Attach the rear cover to the desired location (the tamper spring must be properly pressed)
4. Pull the reader cable through the wall hole and to the interface unit’s box (WJ-80, AS-80)
5. Attach the reader to the rear cover and secure it using the screw
6. Connecting and setting up the reader is described in the WJ-80 or AS-80 manuals.
Cabling
wire signal red +12V (power supply, 60mA)
green brown
D0 (Wiegand 26b data output)
D1 (Wiegand 26b data output)
white grey yellow
blue
TMP (normally closed tamper contact)
TMP (normally closed tamper contact)
BZR (input controlling reader’s sound – connecting to GND generates a beep on the reader)
GND (common ground)
Technical specifications
Power supply
Stand-by consumption
Enclosure protection (EN 60529)
Mechanical endurance (EN 50102)
10 to 16V DC typically 60mA
IP65
IK08
Environmental (EN 50131-1)
Operational temperature range
RFID card
Dimensions class IV – outdoor general
-25 to +60°C
Jablotron PC-01 or PC-02 (EM UNIQUE 125 kHz)
46 x 150.5 x 22.5mm
1m Length of the connection cable
Complies with grade 2 (EN 50131-1, TS 50131-3)
Can be operated according to ERC REC 70-03
FCC ID VL6JA80N
Jablotron Ltd. hereby declares that the JA-80N is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1.
This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the user´s authority to operate the equipment. The original of the conformity assessment can be found at www.jablotron.com
, Technical Support section.
Note: Although this product does not contain any harmful materials we suggest you return the product to the dealer or directly to the producer after use. cca 1 m
Configuring the reader for operation with the WJ-80
If the JA-80N reader is connected to an Oasis control panel and it does not work as described in the manual, then it is not set to the correct
(factory default) operational mode. In such a case:
1. Switch the Oasis control panel to service mode
2. Disconnect the power from the control panel (mains and battery)
3. Get an RFID card ready (PC-01 or PC-02)
4. Disconnect the yellow and brown wires from the WJ-80 interface terminals and connect the wires together
5. Power-up the control panel (reader starts beeping)
6. Disconnect the yellow and brown wires from each other (beeping will terminate)
7. Use the RFID card 4 times (put it close to the reader and after a short beep take it away) – then wait a moment until a few beeps sound (by this procedure you enter “4” without pressing a key, as there are no keys to press)
8. Now use the RFID card 3 times (put it close to the reader and after a short beep take it away) – then wait a moment until a few beeps sound (by this procedure you enter “3” without pressing a key, as there are no keys to press)
9. Disconnect the power from the control panel, connect the yellow and brown wires back up, power-up the control panel and check the proper functioning of the JA-80H keypad
Note: The red LED is lit in normal operating mode. Using a card is confirmed by a flash from the orange LED.
How to set up the JA-80N reader for the AS-80 access system is described in the AS-80 manual.
45 22,5
TAMPER
The JA-80N outdoor RFID card reader MKM51201
1
advertisement
Related manuals
advertisement