Brightlink 18Gbps 16x16 HDMI 2.0 Matrix
with ARC & CEC Function
VER 1.0
BRIGHTLINKAV.COM
Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully before connecting,
operating or adjusting this product. Please keep this manual for future reference.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by electrical
spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly
recommended in order to protect and extend the life of your equipment.
Table of Contents
1. Introduction..................................................................................................................... 1
2. Features........................................................................................................................... 1
3. Package Contents........................................................................................................ 1
4. Specifications................................................................................................................ 2
5. Operation Controls and Functions.............................................................................. 3
6. IR Remote..................................................................................................................... 4
7. EDID Management........................................................................................................5
8. Web GUI User Guide.................................................................................................... 7
9. RS-232 Control Command............................................................................................ 13
10. Application Example................................................................................................... 18
1. Introduction
The 18Gbps 16x16 HDMI Matrix supports the transmission of video (resolution up to 4K2K@
60Hz YUV 4:4:4) and multi-channel high resolution digital audio from 16 HDMI sources to 16
HDMI displays. Audio de-embedded to coaxial audio is supported from 16 HDMI output ports.
While HDMI output ARC function is enabled, the ARC audio from HDMI display devices will be
extracted to coaxial audio output. Each HDMI output of this 16x16 HDMI Matrix supports 4K2K
to 1080P downscaler independently. Control via front panel buttons, IR remote, RS-232, LAN
and Web GUI.
2. Features
☆ HDMI 2.0b, HDCP 2.2/1.x and DVI 1.0 compliant
☆ Video resolution up to 4K2K@60Hz (YUV 4:4:4) on all HDMI ports
☆ Support 18Gbps video bandwidth
☆ HDR, HDR10, HDR10+, Dolby Vision and HLG are supported.
☆ Support 4K->1080P Down Scaler for each output port
☆ HDMI audio pass-through up to 7.1CH HD audio (LPCM, Dolby TrueHD and DTS-HD
Master Audio)
☆ Audio de-embedded is supported via coax ports
☆ ARC, CEC and smart EDID management are supported
☆ 1U rack mounted design with front panel OLED display
☆ Control via front panel buttons, IR remote, RS-232, LAN and Web GUI
3. Package Contents
① 1 x 18Gbps 16x16 HDMI Matrix
② 1 x 24V/3.75A Power Adapter
③ 1 x IR Remote
④ 1 x RS-232 serial cable (1.5 meters, male to female head)
⑤ 2 x Mounting Ear
⑥ 1 x User Manual
- 1 / 18 -
4. Specifications
Technical
HDMI Compliance
HDMI 2.0b
HDCP Compliance
Video Bandwidth
HDCP 2.2/1.x
18Gbps
Up to 4K2K@60Hz (4:4:4)
Video Resolution
Color Space
Color Depth
RGB, YCbCr 4:4:4/4:2:2/4:2:0
8-bit, 10-bit, 12-bit
HDMI Audio Formats
(Pass-through)
LPCM 2/5.1/7.1, Dolby Digital, DTS 5.1, Dolby Digital+,
Dolby TrueHD, DTS-HD Master Audio, Dolby Atmos, DTS:X
Coax Audio Formats
ESD Protection
LPCM 2.0, Dolby Digital / Plus, DTS 5.1
HDR10,HDR10+,Dolby Vision, HLG
Human-body Model:
±8kV (Air-gap discharge) , ±4kV (Contact discharge)
Connection
Input Ports
16×HDMI Type A [19-pin female]
HDR formats
Output Ports
Control Ports
16×HDMI Type A [19-pin female]
16×Coax Audio (RCA)
1×TCP/IP [RJ45]
1×RS-232 [D-Sub 9]
Mechanical
Housing
Metal Enclosure
Color
Dimensions
Black
Weight
3.1kg
Power Supply
Input: AC 100 - 240V 50/60Hz, Output: DC 24V/3.75A
(US/EU standard, CE/FCC/ULcertified)
Power Consumption
Operating Temperature
76.8W
-10°C ~ 45°C / 14°F ~ 113°F
Storage Temperature
-20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity
20~90% RH (non-condensing)
Resolution / Cable length
4K60 Feet / Meters
4K30 Feet / Meters
1080P60 Feet / Meters
16ft / 5M
32ft / 10M
50ft / 15M
HDMI IN / OUT
440mm (W)×200mm (D)×44mm (H)
The use of “Premium High Speed HDMI” cable is highly recommended.
- 2 / 18 -
5. Operation Controls and Functions
Front Panel
1
2
3
5
4
1
2
3
4
5
6
7
8
AV
MENU
UP
9
10
11
12
13
14
15
16
ALL
ENTER
DOWN
6
NO.
1
2
3
4
Name
Function Description
Display matrix switching status, input / output port, EDID,
OLED screen
Baud rate, IP Address.
The LED will illuminate in green when the product is connected
Power LED
to power supply, and red when the product is on standby.
You
need to press input button (1~16) firstly, then press the
Input / Output
“AV”
button, finally press input button (1~16, including
buttons
“ALL”) to select the corresponding input and output ports.
inpuinput
outputsignal
portsrce
for the
outpu
AV: Usedand
to switch
source
to output.
te.g.
port.Pressing “1→AV→3” represents signal source 1 is
output to display 3.
AV / ALL buttons
All: It represents all the output ports.
e.g. Pressing “1→AV→ALL” represents signal source 1 is
output to all displays.
4
5
①Switching status check: On the initial OLED display
screen, press “MENU” button to enter the Matrix switching
status interface, then press “UP/DOWN” button to check the
switching state of all ports.
②EDID setting: On the initial OLED display screen, press
“MENU” button to enter the EDID setting interface, press
“UP/DOWN” button to select the required EDID, and press
the “ENTER” button. A prompt “copy to input :” will appear.
Then press “UP/DOWN” button to select the input port you
MENU / ENTER need to set, and press “ENTER” button again to confirm.
/ UP /DOWN
③Baud rate setting: On the initial OLED display screen,
press “MENU” button to enter the Baud rate interface, and
press “UP/DOWN” button to select the required Baud rate,
finally press the “ENTER” button to confirm the setting.
④IP Address check: On the initial OLED display screen,
press “MENU” button to enter the IP interface, then press
“UP/DOWN” button to check the current IP address.
Pressing the “MENU” button again will return to the initial
OLED display status.
6
IR Window
IR receiver window, it only receives the IR remote signal
from this product.
- 3 / 18 -
Rear Panel
1
3
TCP/IP
2
1
RS-232
1
2
3
4
5
6
7
8
INPUT
9
10
11
12
2
13
3
14
4
15
16
5
1
6
2
7
3
8
4
AUDIO OUT
5
4 5
9
10
6
7
11
8
6
OUTPUT
12
9
13
10
14
11
12
15
13
16
14
Name
1
TCP/IP port
2
RS-232 port
3
AUDIO OUT
(1-16)
4
DC 24V
TCP/IP control port, connect to PC or router with an RJ45
cable.
Connect to a PC or control system by D-Sub 9-pin cable to
transmit RS-232 command.
Coaxial audio output port, connect to audio output device
such as audio amplifier via a coaxial cable.
Connect to 24V power adapter.
5
GND
INPUT ports
(1-16)
Connect the housing to the ground.
HDMI input ports , connect to HDMI source device such as
DVD or set-top box with an HDMI cable.
7
15
16
7
No.
6
DC 24V
4
Function Description
OUTPUT ports HDMI output ports, connect to HDMI display device such as
TV or monitor with an HDMI cable.
(1-16)
6. IR Remote
1
① Power on or Standby: Power on the Matrix or set it to
standby mode.
② Input 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16:
Select input source button.
2
③ Output 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16:
Select output source button.
④ All: Select all output sources simultaneously.
3
4
For example, when you press input “1” button and then
press the “All” button, at this time the input “1” source will
be output to all display devices.
Operation instruction: You need to press the input button
firstly and then press output button. For example,
Press Input-Y
(Y means input button from 1 to 16)
Then press Output-X
(X means output button from 1 to 16, including “All” button)
- 4 / 18 -
7. EDID Management
This Matrix has 21 factory defined EDID settings, 2 user-defined EDID modes and 16 copy EDID
modes. You can select defined EDID mode or copy EDID mode to input port through front panel
buttons, RS-232 control or Web GUI.
On-panel button operation: On the initial OLED display screen, press “MENU” button to enter
the EDID setting interface, press “UP/DOWN” button to select the required EDID, and press
the “ENTER” button. A prompt “copy to input :” will appear. Then press “UP/DOWN” button to
select the input port you need to set, and press “ENTER” button again to confirm this operation.
RS-232 control operation: Connect the Matrix to PC with a serial cable, then open a Serial
Command tool on PC to send ASCII command “s edid in x from z!” to set EDID. For details,
please refer to “EDID Setting” in the ASCII command list of “9. RS-232 Control Command”.
Web GUI Operation: Please check the EDID management in the “Input page” of “8. Web
GUI User Guide”.
- 5 / 18 -
The defined EDID setting list of the product is shown as below:
EDID Mode
1
2
3
4
EDID Description
1080p, Stereo Audio 2.0
1080p, Dolby/DTS 5.1
1080p, HD Audio 7.1
1080i, Stereo Audio 2.0
5
6
7
1080i, Dolby/DTS 5.1
1080i, HD Audio 7.1
3D, Stereo Audio 2.0
8
9
10
3D, Dolby/DTS 5.1
3D, HD Audio 7.1
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
4K2K30_444, Stereo Audio 2.0
4K2K30_444, Dolby/DTS 5.1
4K2K30_444, HD Audio 7.1
4K2K60_420, Stereo Audio 2.0
4K2K60_420, Dolby/DTS 5.1
4K2K60_420, HD Audio 7.1
4K2K60_444, Stereo Audio 2.0
4K2K60_444, Dolby/DTS 5.1
4K2K60_444, HD Audio 7.1
4K2K60_444, Stereo Audio 2.0 HDR
4K2K60_444, Dolby/DTS 5.1 HDR
4K2K60_444, HD Audio 7.1HDR
USER1
USER2
Copy from hdmi output 1
Copy from hdmi output 2
Copy from hdmi output 3
Copy from hdmi output 4
Copy from hdmi output 5
Copy from hdmi output 6
Copy from hdmi output 7
Copy from hdmi output 8
Copy from hdmi output 9
Copy from hdmi output 10
Copy from hdmi output 11
Copy from hdmi output 12
Copy from hdmi output 13
Copy from hdmi output 14
Copy from hdmi output 15
Copy from hdmi output 16
- 6 / 18 -
8. Web GUI User Guide
The Matrix can be controlled by Web GUI. The operation method is shown as below:
Step 1: Get the current IP Address.
The default IP address is 192.168.1.100. You can get the current Matrix IP address in two ways:
The first way: You can get the IP address via panel buttons. On the initial OLED display, press
“MENU” button to enter the IP interface, then press “UP/DOWN” button to check the current
IP address.
The second way: You can get the IP address via RS-232 control. Send the command “ r ipconfig!”
through an ASCII Command tool, then you’ll get the feedback information as shown below:
IP:192.168.62.100 in the above figure is the IP Address of the Matrix (the IP address is
variable, depending on what the specific machine returns).
For the details of ASCII control, please refer to “9. RS-232 Control Command”.
Step 2: Set the IP address of the PC to be in the same network segment with the Matrix.
Step 3: Input the IP address of the Matrix into your browser on the PC to enter Web GUI page.
After entering the Web GUI page, there will be a Login page, as shown below:
Select the Username from the list and enter the password. The default passwords are:
Username
Password
User
user
- 7 / 18 -
Admin
admin
After entering the password, click the “LOGIN” button and the following Status page will
appear.
■ Status Page
The Status page provides basic information about the Model, the installed firmware version
and the network settings of the device.
■ Video Page
You can do the following operations on the Video page:
① Output: The current device’s OUTPUT port. You can select signal source for it.
② All Output: All OUTPUT ports for the current device. You can select signal source for them.
③ Input: You can click the drop-down menu to select signal source for the corresponding
OUTPUT port .
④ Presets Name: You can name the current scene with maximum length of 12 characters
(Chinese name is unsupported).
⑤ Presets Set: You can restore the settings of the last saved audio-video matrix switching
relationship.
⑥ Presets Save: You can save audio-video matrix switching relationship.
⑦ Presets Clear: You can clear the saved audio-video matrix switching relationship.
- 8/ 18 -
■ Input Page
You can do the following operations on the Input page:
① Inputs: Input channel of the device.
② Active: It indicates whether the channel is connected to a signal source.
③ Name: The input channel’s name. You can modify it by entering the corresponding name
(max length: 12 characters) in the input box (Chinese name is unsupported).
④ EDID: You can set the current channel’s EDID. The specific operation is as follows:
Set EDID for the User
Click the “Browse” button, then select the bin file. If you select the wrong EDID file, there will
be a prompt, as shown in the following figure:
Make sure to select the correct file, then you can check the name of the selected file. Select
“User 1” or “User 2”, then click “Upload”. After successful setting, it will prompt as follows:
Download the EDID File of the Corresponding Input Channel
Click the drop-down box of “Select EDID File” to select the corresponding input channel. Then
click “Download” to download the corresponding EDID file.
- 9 / 18 -
■ Output Page
You can do the following operations on the Output page:
① Outputs: Output channel of the device.
② Name: The current output channel’s name. You can modify it by entering the corresponding
name (max length: 12 characters) in the input box (Chinese name is unsupported).
③ Cable: It indicates the connection status of output ports. When the output port is connected
to the display, it shows green, otherwise, it shows gray.
④ Scalar Mode: Set the current output resolution mode.
⑤ ARC: Turn on/off the ARC function.
⑥ Stream: Turn on/off the output stream.
■ CEC Page
You can perform CEC management on this page:
① Input Control: You can control the operation of each input source by clicking the icons
on the page.
② Output Control: You can control the operation of each display, such as power on/off,
volume +/-, active source switching.
- 10 / 18 -
■ Network Page
Set the Default Network
Click “Set Network Defaults”, there will be a prompt, as shown in the following figure:
Click “OK” to search the IP Address again, as shown in the following figure:
After searching is completed, it will switch to the login page, the default network setting is
completed.
- 11 / 18 -
Modify Username
Click the “User” button, enter the correct Old Password, New Password, and Confirm
Password, then click “Save”. After successful modification, there will be a prompt, as shown
in the following figure:
Note: Input rules for changing passwords:
(1) The password can’t be empty.
(2) New Password can’t be the same as Old Password.
(3) New Password and Confirm Password must be the same.
Modify Network Setting
Modify the Mode/IP Address/Gateway/Subnet Mask/Telnet Port as required, click “Save” to
save the settings, then it will come into effect.
After modification, if the Mode is “Static”, it will switch to the corresponding IP Address; if the
Mode is “DHCP”, it will automatically search and switch to the IP Address assigned by the
router.
■ System Page
- 12 / 18 -
① Panel Lock: Click “Panel Lock” to lock/unlock panel buttons. “On” indicates that panel
buttons are unavailable; “Off” indicates panel buttons are available.
② Beep: Click “Beep” to turn on/off the beep.
③ LCD: You can turn on/off the LCD, and set the turn-on time (15s/30s/60s).
④ Serial Baud Rate: Click the value to set the Serial Baud Rate.
⑤ Firmware Update: Click “Browse” to select the update file, then click “Update” to complete
firmware update.
⑥ Factory Reset: You can reset the unit to factory defaults by clicking “Reset”.
⑦ Reboot: You can reboot the unit by clicking “Reboot”.
Note: After reset/reboot, it will switch to the login page.
9. RS-232 Control Command
The product also supports RS-232 control. You need a serial cable with RS-232 male head and
DB9 transfer USB male head. The RS-232 head of the serial cable is connected to the RS-232
control port with DB 9 at the rear of the Matrix, and the USB head of the serial cable is connected
to a PC. The connection method is as follows:
↑
RS-232
Then, open a Serial Command tool on PC to send ASCII command to control the Matrix.
The ASCII command list about the product is shown as below.
ASCII Command
Serial port protocol. Baud rate: 115200,
Data bits: 8bit, Stop bits:1, Check bit: 0
x - Parameter 1
y - Parameter 2
! - Delimiter
Command Code
Function Description
Example
Feedback
Default Setting
Power
s power z!
Power on/off the device,z=0~1
(z=0 power off, z=1 power on)
s power 1!
r power!
Get current power state
r power!
s reboot!
Reboot the device
s reboot!
help!
List all commands
help!
r type!
Get device model
r type!
Power on
System Initializing...
power on
Initialization Finished!
FW version x.xx.xx
power on/power off
Reboot...
System Initializing...
Initialization Finished!
FW version x.xx.xx
System Setup
- 13 / 18 -
HDP-MXB1616
Command Code
Function Description
Example
Feedback
r status!
Get device current status
r status!
Get the unit all status:
power, beep, lock, in/
out connection, video/
audio crosspoint,
edid, scaler, network
status
r fw version!
Get Firmware version
r fw version!
MCU BOOT: Vx.xx.xx
MCU APP: Vx.xx.xx
WEB GUI: Vx.xx
r link in x!
Get the connection status of the
x input port，x=0~16(0=all)
r link in 1!
hdmi input 1: connect
r link out y!
Get the connection status of the
y output port，y=0~16(0=all)
r link out 1!
hdmi output 1: connect
s reset!
Reset to factory defaults
s reset!
s beep z!
Enable/Disable buzzer function,
z=0~1(z=0 beep off, z=1 beep on) s beep 1!
r beep!
Get buzzer state
s lock z!
r lock!
s lcd on time z!
r lcd mode!
s save preset z!
s recall preset z!
s clear preset z!
Lock/Unlock front panel button,
z=0~1(z=0 lock off,z=1 lock on)
Get panel button lock state
Set LCD screen remain on time,
z=0~4(0:off, 1:always on, 2:15s,
3:30s, 4:60s)
Get the backlight status of lcd
screen
Save switch state between all
output port and the input port to
preset z, z=1~8
Call saved preset z scenarios,
z=1~8
Clear stored preset z scenarios,
z=1~8
Reset to factory defaults
System Initializing...
Initialization Finished!
FW version x.xx.xx
beep on
beep on
beep off
r beep!
beep on / beep off
s lock 1!
panel button lock on
panel button lock off
r lock!
panel button lock on/off
s lcd on time 1!
lcd on 15 seconds
r lcd mode!
lcd always on
s save preset 1!
save to preset 1
panel button
lock off
lcd on 30
seconds
s recall preset 1! recall from preset 1
s clear preset 1!
clear preset 1
Get preset z information, z=1~8
r preset 1!
video/audio crosspoint
s in x av out y!
Set input x to output y，
x=1~16, y=0~16(0=all)
s in 1 av out 2!
input 1 -> output 2
r av out y!
Get output y signal status
y=0~16(0=all)
r av out 0!
input 1 -> output 1
input 2 -> output 2
……
input 16 -> output 16
r preset z!
Default Setting
Output Setting
Set output y stream on/off,
s hdmi y stream z! y=0~16(0=all)
z=0~1(0:disable,1:enable)
r hdmi y stream!
Get output y stream status,
y=0~16(0=all)
Set hdmi output y port output
s hdmi y scaler z! scaler mode，y=0~16 (0=all),
z=1~3(1=bypass, 2=4k->1080p,
3=Auto)
PTP
Enable hdmi output 1
stream
s hdmi 1 stream 1! Disable hdmi output 1
stream
enable
s hdmi 0 stream 1! Enable hdmi all outputs
stream
Disable hdmi all
outputs stream
Enable hdmi output 1
r hdmi 1 stream!
stream
hdmi output 1 set to
hdmi all outputs
s hdmi 1 scaler 1! bypass mode
set to bypass
s hdmi 0 scaler 1! hdmi all outputs set to mode
bypass mode
- 14 / 18 -
Command Code
r hdmi y scaler!
Function Description
Get hdmi output y port output
mode y=0~16(0=all)
Example
r hdmi 1 scaler !
Feedback
Default Setting
hdmi output 1 set to
bypass mode
EDID Setting
Set input x EDID from default
EDID z,
x=0~16 (0=all),z=1~39
1, 1080p,Stereo Audio 2.0
2, 1080p,Dolby/DTS 5.1
3, 1080p,HD Audio 7.1
4, 1080i,Stereo Audio 2.0
5, 1080i,Dolby/DTS 5.1
6, 1080i,HD Audio 7.1
7, 3D,Stereo Audio 2.0
8, 3D,Dolby/DTS 5.1
9, 3D,HD Audio 7.1
10, 4K2K30_444,Stereo Audio 2.0
11, 4K2K30_444,Dolby/DTS 5.1
12, 4K2K30_444,HD Audio 7.1
13, 4K2K60_420,Stereo Audio 2.0
14, 4K2K60_420,Dolby/DTS 5.1
15, 4K2K60_420,HD Audio 7.1
16, 4K2K60_444,Stereo Audio 2.0
input 1 EDID:1080p,
17, 4K2K60_444,Dolby/DTS 5.1
18, 4K2K60_444,HD Audio 7.1
s edid in 1 from 1! Stereo Audio 2.0
s edid in x from z! 19, 4K2K60_444,Stereo Audio 2.0
HDR
20, 4K2K60_444,Dolby/DTS 5.1 s edid in 0 from 1! all inputs EDID:1080p,
HDR
Stereo Audio 2.0
21, 4K2K60_444,HD Audio 7.1
HDR
22, USER1
23, USER2
24, copy from hdmi output 1
25, copy from hdmi output 2
26, copy from hdmi output 3
27, copy from hdmi output 4
28, copy from hdmi output 5
29, copy from hdmi output 6
30, copy from hdmi output 7
31, copy from hdmi output 8
32, copy from hdmi output 9
33, copy from hdmi output 10
34, copy from hdmi output 11
35, copy from hdmi output 12
36, copy from hdmi output 13
37, copy from hdmi output 14
38, copy from hdmi output 15
39, copy from hdmi output 16
r edid in x!
Get EDID status of the input x，
x=0~16(0=all input)
r edid data hdmi y! Get the EDID data of the hdmi
output y port，y=1~16
r edid in 0!
1080p,Stereo
Audio 2.0
input 1 EDID: 4K2K60_444,
Stereo Audio 2.0
input 2 EDID: 4K2K60_444,
Stereo Audio 2.0
input 3 EDID: 4K2K60_444,
Stereo Audio 2.0
input 4 EDID: 4K2K60_444,
Stereo Audio 2.0
r edid data hdmi 1! EDID: 00 FF FF FF FF
FF FF 00 ………
Audio Setting
s hdmi y arc z!
Turn on/off ARC of HDMI output y, s hdmi 1 arc 1!
y=0~16(0=all)
z=0~1(z=0,off,z=1 on)
s hdmi 0 arc 1!
r hdmi y arc!
Get the ARC state of HDMI output
r hdmi 1 arc!
y，y=0~16(0=all)
-15 / 18 -
hdmi output 1 arc on
hdmi output 1 arc off
hdmi all outputs arc on
hdmi all outputs arc off
hdmi output 1 arc on
off
Command Code
Function Description
Example
Feedback
CEC Setting
s cec in x on!
set input x power on by CEC,
x=0~16(0=all input)
s cec in 1 on!
input 1 power on
s cec in x off!
set input x power off by CEC,
x=0~16(0=all input)
s cec in 1 off!
input 1 power off
s cec in x menu!
set input x open menu by CEC,
x=0~16(0=all input)
s cec in 1 menu!
input 1 open menu
s cec in x back!
set input x back operation by
CEC, x=0~16(0=all input)
s cec in 1 back!
s cec in x up!
set input x menu up operation by
s cec in 1 up!
CEC, x=0~16(0=all input)
input 1 menu up
operation
s cec in x down!
set input x menu down operation
s cec in 1 down!
by CEC, x=0~16(0=all input)
input 1 menu down
operation
s cec in x left!
set input x menu left operation by
s cec in 1 left!
CEC, x=0~16(0=all input)
input 1 menu left
operation
s cec in x right!
set input x menu right operation
by CEC, x=0~16(0=all input)
s cec in 1 right!
input 1 menu right
operation
s cec in x enter!
set input x menu enter by CEC,
x=0~16(0=all input)
s cec in 1 enter!
iInput 1 menu enter
operation
s cec in x play!
set input x play by CEC,
x=0~16(0=all input)
s cec in 1 play!
input 1 play operation
s cec in x pause!
set input x pause by CEC,
x=0~16(0=all input)
s cec in 1 pause!
iInput 1 pause
operation
s cec in x stop!
s cec in x rew!
set input x stop by CEC,
x=0~16(0=all input)
set input x rewind by CEC,
x=0~16(0=all input)
input 1 back operation
s cec in 1 stop!
input 1 stop operation
s cec in 1 rew!
input 1 rewind
operation
s cec in x mute!
set input x volume mute by CEC,
s cec in 1 mute!
x=0~16(0=all input)
input 1 volume mute
s cec in x vol-!
set input x volume down by CEC,
s cec in 1 vol-!
x=0~16(0=all input)
input 1 volume down
s cec in x vol+!
set input x volume up by CEC,
x=0~16(0=all input)
s cec in 1 vol+!
input 1 volume up
s cec in x ff!
set input x fast forward by CEC,
x=0~16(0=all input)
s cec in 1 ff!
input 1 fast forward
operation
s cec in x previous!
set input x previous by CEC,
x=0~16(0=all input)
s cec in 1 previous!
input 1 previous
operation
s cec in x next!
set input x next by CEC,
x=0~16(0=all input)
s cec in 1 next!
input 1 next operation
s cec hdmi out y
on!
set hdmi output y power on by
CEC, y=0~16(0=all output)
s cec hdmi out 1
on!
hdmi output 1 power
on
s cec hdmi out y off
set hdmi output y power off by
CEC, y=0~16(0=all output)
s cec hdmi out 1
on!
hdmi output 1 power
off
s cec hdmi out y
mute!
set hdmi output y volume mute by s cec hdmi out 1
CEC, y=0~16(0=all output)
mute!
hdmi output 1 volume
mute
s cec hdmi out y
vol-!
set hdmi output y volume down
by CEC, y=0~16(0=all output)
s cec hdmi out 1
vol-!
hdmi output 1 volume
down
s cec hdmi out y
vol+!
set hdmi output y volume up by
CEC, y=0~16(0=all output)
s cec hdmi out 1
vol+!
hdmi output 1 volume
up
s cec hdmi out y
active!
set hdmi output y active source
by CEC, y=0~16(0=all output)
s cec hdmi out 1
active!
hdmi output 1 active
source
- 16 / 18 -
Default Setting
Command Code
Example
Function Description
Feedback
Network Setting
r ipconfig!
Get the Current IP Configuration r ipconfig!
r mac addr!
Get network MAC address
r mac addr!
s ip mode z!
Set network IP mode to static IP
or DHCP,
z=0~1 (z=0 Static, z=1 DHCP )
s ip mode 0!
r ip mode!
Get network IP mode
r ip mode!
s ip addr
xxx.xxx.xxx.xxx!
Set network IP address
s ip addr
192.168.1.100!
r ip addr!
Get network IP address
r ip addr!
s subnet
xxx.xxx.xxx.xxx!
Set network subnet mask
s subnet
255.255.255.0!
r subnet!
Get network subnet mask
r subnet!
s gateway
xxx.xxx.xxx.xxx!
Set network gateway
s gateway
192.168.1.1!
r gateway!
Get network gateway
r gateway!
IP Mode: Static
IP: 192.168.1.72
Subnet Mask:
255.255.255.0
Gateway: 192.168.1.1
TCP/IP port=8000
Telnet port=10
Mac address:
00:1C:91:03:80:01
Mac address:
00:1C:91:03:80:01
Set IP mode:Static
(Please use "s net
reboot!" command or
repower device to
apply new config!)
IP Mode: Static
Set IP address:
192.168.1.100 (Please
use "s net reboot!"
command or repower
device to apply new
config!)
DHCP on, Device can't
config static address,
set DHCP off first.
IP address:
192.168.1.100
Set subnet Mask:
255.255.255.0
(Please use "s net
reboot!" command or
repower device to apply
new config!)
DHCP on, Device can't
config subnet mask,
set DHCP off first.
Subnet Mask:
255.255.255.0
Set gateway:
192.168.1.1
Please use "s net
reboot!" command or
repower device to
apply new config!
DHCP on, Device can't
config gateway, set
DHCP off first.
Gateway:192.168.1.1
r tcp/ip port!
Set network TCP/IP port
(x=1~65535)
Get network TCP/IP port
r tcp/ip port!
TCP/IP port:8000
s telnet port x!
Set network telnet port
(x=1~65535)
s telnet port 23!
Set Telnet port:23
r telnet port!
Get network telnet port
r telnet port!
Telnet port:23
s tcp/ip port x!
s tcp/ip port 8000! Set TCP/IP port:8000
- 17 / 18 -
Default Setting
s net reboot!
Example
Feedback
s network reboot!
Network reboot…
IP Mode: Static
IP: 192.168.1.72
Subnet Mask:
255.255.255.0
Gateway: 192.168.1.1
TCP/IP port=8000
Telnet port=10
Mac address:
00:1C:91:03:80:01
Function Description
Command Code
Reboot network modules
Default Setting
11. Application Example
PC
Amplifier
TCP/IP
Power Supply
1
RS-232
1
2
3
4
5
6
PC
7
8
INPUT
9
10
11
12
2
13
3
14
4
15
16
5
1
6
2
7
3
8
4
AUDIO OUT
5
9
10
6
7
11
8
OUTPUT
12
9
13
10
14
11
TV box
TV
DVD or Blu-ray Player
- 18 / 18 -
Monitor
12
15
13
16
14
DC 24V
15
16
">
