IC693MDL632

IC693MDL632
This Datasheet is for the
IC693MDL632
125 Volt DC Positive/Negative Logic Input, 8 Point
http://www.cimtecautomation.com/parts/p-14655-ic693mdl632.aspx
Provides the wiring diagrams and installation guidelines for this GE Series 90-30
module.
For further information, please contact Qualitrol Technical Support at
1-800-784-9385
[email protected]
6
Discrete Input Modules
125 Volt DC Positive/Negative Logic Input, 8 Point
IC693MDL632
This 125 volt DC Positive/Negative Logic Input module provides 8 input points in two isolated
groups with four points in each group. Each group has a separate common associated with it
(the two commons are not tied together inside the module). The input module is designed to
have either positive logic characteristics in that it sinks current from the input devices to the
user common or negative power bus, or negative logic characteristics in that it sources current
through the input devices to the user common or positive power bus. The input device is
connected between the power bus and the module input. Current into an input point results in a
logic 1 in the input status table (%I). Input characteristics are compatible with a wide range of
input devices, such as pushbuttons, limit switches, and electronic proximity switches. Power
to operate field devices must be supplied by the user.
LED indicators which provide the ON/OFF status of each point are located at the top of the
module. This LED block has two horizontal rows with eight green LEDs in each row. This
module uses the top row labeled A1 through 8 (points 1 through 8). An insert goes between
the inside and outside surface of the hinged door. The surface towards the inside of the module
(when the hinged door is closed) has circuit wiring information, and circuit identification
information can be recorded on the outside surface. The outside left edge of the insert is
color-coded red to indicate a high-voltage module.
This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC
system.
Table 6-5. Specifications for IC693MDL632
Rated Voltage
Input Voltage Range
Inputs per Module [
Isolation
Input Current
125 volts DC (Positive or Negative Logic)
0 to +150 volts DC
8 (two groups of four inputs)
1500 volts between field side and logic side
500 volts between groups
4.5 mA typical
Input Characteristics
On-state Voltage
Off-state Voltage
On-state Current
Off-state Current
On response Time
Off response Time
90 to 150 volts DC
0 to 30 volts DC
3.1 mA
1.1 mA maximum
7 ms typical
7 ms typical
Internal Power Consumption
40 mA from the 5 volt bus on the backplane
36 mA (typical) from user input supply (all inputs
ON)
[ Number of inputs on is dependent upon ambient temperature as shown in figure 6–11.
Refer to Appendix B for product standards and general specifications.
GFK-0898F
Chapter 6 – Discrete Input Modules
6-9
6
IC693MDL632 Input Module Field Wiring Information
The following figure provides wiring information for connecting user supplied input devices
and power source to the 125 volt DC positive/negative logic input module. The negative logic
connections are shown in dashed lines.
a44959
MODULE CIRCUITRY
TERMINALS FIELD WIRING
1
2
3
4
22K
5
6
7
0.1 µ f
680
8
9
OPTICAL
COUPLER
10
5.6K
11
12
13
14
15
16
17
18
19
20
ÎÎ
Î
ÎÎ
Î
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎ
Î
ÎÎ
Î
ÎÎÎ
ÎÎÎ
A1
A2
A3
A4
A5
A6
A7
A8
Figure 6-7. Field Wiring - 125 Volt DC Positive /Negative Logic Input Module IC693MDL632
a44960
8
145V SUPPLY
6
150V SUPPLY
NUMBER
OF
INPUTS 4
ON
2 INPUTS ON
2
2 INPUTS ON
45°C
10°C
20°C 30°C 40°C 50°C 60°C
AMBIENT TEMPERATURE (°C)
Figure 6-8. Input Points vs. Temperature for IC693MDL632
6-10
Series 90-30 PLC I/O Module Specifications – July 2000
GFK-0898F
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement