Finder 22.34.0.230.4640 Relay 2 NO/2 NC 230V DC/AC IP20 Industrial Relay Data Sheet
Below you will find brief information for 22 Series 22.32.0.xxx.1xx0, 22 Series 22.32.0.xxx.4xx0, 22 Series 22.34.0.xxx.1xx0, 22 Series 22.34.0.xxx.4xx0, 22 Series 22.44.0.xxx.4xx0. These contactors are designed for use in a variety of applications, including industrial, commercial, and residential settings, can be used to control various types of loads, such as motors, lights, and appliances. These contactors are designed for use in a variety of applications, including industrial, commercial, and residential settings. They can be used to control various types of loads, such as motors, lights, and appliances. They are available in a variety of configurations, including 2-pole and 4-pole versions. They are also available in a variety of contact materials, including AgNi and AgSnO2. They can be used in various applications, including industrial, commercial, and residential settings.
advertisement
22 Series - Modular contactors 25 - 40 - 63 A
Features
22.32.0.xxx.1xx0
25 A modular contactor - 2 pole
•
•
•
•
•
•
•
•
•
•
•
17.5 mm wide
NO contact gap ≥ 3 mm, double break
Continuous duty for the coil and contacts
AC/DC silent coil (with varistor protection)
Protective separation (reinforced insulation) between coil and contacts
Mechanical and LED indicators as standard
Auto-On-Off selector version available
AgNi and AgSnO
2 contact versions available
Compliant with EN 61095: 2009
Auxiliary contact module available, quick-assembly with the main contactor
(1 NO + 1 NC and 2 NO versions)
35 mm rail (EN 60715) mount
•
AgNi contacts, specifically intended for resistive and slightly inductive loads as well as for motor loads
22.32.0.xxx.4xx0
•
AgSnO
2 contacts, specifically intended for lamp loads and for high inrush current loads
22.32...1xx0 / 22.32...4xx0
Screw terminal
22
SERIES
2 NO
(x3x0)
1 NO + 1 NC
(x5x0)
2 NC
(x4x0)
* Contact gap ≥ 3 mm for NO contacts only;
NC contacts ≥ 1.5 mm
For outline drawings see page 8
Contact specification
Contact configuration
Rated current/Maximum peak current
Rated voltage
A
V AC
Rated load AC1 / AC-7a (per pole @ 250 V) VA
Rated current AC3 / AC-7b
Rated load AC15 (per pole @ 230 V)
Single-phase motor rating (230 V AC)
A
VA kW
Rated current AC-7c A
230 V lamps rating: incandescent or halogen W compact fluorescent (CFL) W electronic ballast fluorescent tubes W electromagnetic ballast compens. fluorescent tubes W
Breaking capacity DC1: 30/110/220 V A
Minimum switching load mW (V/mA)
Contact material
Coil specification
Nominal voltage (U
N
) V DC/AC (50/60 Hz)
Rated power AC/DC VA (50 Hz)/W
Operating range
Holding voltage
Must drop-out voltage
Technical data
DC/AC (50/60 Hz)
DC/AC (50/60 Hz)
DC/AC (50/60 Hz)
Mechanical life AC/DC
Electrical life at rated load AC-7a cycles cycles
Operate/release time ms
Insulation between coil and contacts (1.2/50 μs) kV
Ambient temperature range °C
Protection category
Approvals (according to type)
2 NO, 3 mm * (or 1 NO + 1 NC or 2 NC)
25 / 80 25 / 120
250 / 440 250 / 440
6,250
10
1,800
1
—
—
—
—
—
25/5/1
1,000 (10/10)
AgNi
6,250
10
1,800
1
10
2,000
200
800
500
25/5/1
1,000 (10/10)
AgSnO
2
12 - 24 - 48 - 60 - 120 - 230 12 - 24 - 48 - 60 - 120 - 230
2 /2.2
2 / 2.2
(0.8…1.1) U
N
0.4 U
N
0.1 U
N
(0.8…1.1) U
N
0.4 U
N
0.1 U
N
2 · 10 6
70 · 10 3
30 / 20
6
–20…+50
IP20
2 · 10
30 · 10 3
30 / 20
6
–20…+50
IP20
6
1
22
SERIES
22 Series - Modular contactors 25 - 40 - 63 A
Features
22.34.0.xxx.1xx0
22.34.0.xxx.4xx0
25 A modular contactor - 4 pole
•
35 mm wide
•
NO contact gap ≥ 3 mm, double break
•
Continuous duty for the coil and contacts
•
AC/DC silent coil (with varistor protection)
•
•
Protective separation (reinforced insulation) between coil and contacts
Mechanical and LED indicators as standard
•
Auto-On-Off selector version available
•
AgNi and AgSnO
2 contact versions available
•
Compliant with EN 61095: 2009
•
Auxiliary contact module available, quick-assembly with the main contactor
(1 NO + 1 NC and 2 NO versions)
•
35 mm rail (EN 60715) mount
•
AgNi contacts, specifically intended for resistive and slightly inductive loads as well as for motor loads
•
AgSnO
2 contacts, specifically intended for lamp loads and for high inrush current loads
22.34...1xx0 / 22.34...4xx0
Screw terminal
4 NO
(x3x0)
3 NO + 1 NC
(x7x0)
2 NO + 2 NC
(x6x0)
* Contact gap ≥ 3 mm for NO contacts only;
NC contacts ≥ 1.5 mm
For outline drawings see page 8
Contact specification
Contact configuration
Rated current/Maximum peak current A
Rated voltage V AC
Rated load AC1 / AC-7a (per pole @ 250 V) VA
Rated current AC3 / AC-7b A
Rated load AC15 (per pole @ 230 V) VA
Three-phase motor rating (400 - 440 V AC) kW
Rated current AC-7c A
230 V lamps rating: incandescent or halogen W compact fluorescent (CFL) W electronic ballast fluorescent tubes W electromagnetic ballast compens. fluorescent tubes W
Breaking capacity DC1: 30/110/220 V
Minimum switching load
A mW (V/mA)
Contact material
Coil specification
Nominal voltage (U
N
) V DC/AC (50/60 Hz)
Rated power AC/DC VA (50 Hz)/W
Operating range
Holding voltage
Must drop-out voltage
Technical data
DC/AC (50/60 Hz)
DC/AC (50/60 Hz)
DC/AC (50/60 Hz)
Mechanical life AC/DC
Electrical life at rated load AC-7a
Operate/release time cycles cycles ms
Insulation between coil and contacts (1.2/50 μs) kV
Ambient temperature range °C
Protection category
Approvals (according to type)
4 NO, 3 mm * (or 3NO + 1NC or 2NO + 2NC)
25 / 80 25 / 120
250 / 440
6,250
250 / 440
6,250
10
1,800
4
—
—
—
—
—
25/5/1
1,000 (10/10)
AgNi
10
1,800
4
10
2,000
200
800
500
25/5/1
1,000 (10/10)
AgSnO
2
12 - 24 - 48 - 60 - 120 - 230 12 - 24 - 48 - 60 - 120 - 230
2 / 2.2
(0.8…1.1) U
N
0.4 U
N
0.1 U
N
2 / 2.2
(0.8…1.1) U
N
0.4 U
N
0.1 U
N
2 · 10
150 · 10
18 / 40
6
IP20
6
3
–20…+50
2 · 10
30 · 10
6
6
18 / 40
3
–20…+50
IP20
2
22 Series - Modular contactors 25 - 40 - 63 A
Features
22.44.0.xxx.4xx0
22.64.0.xxx.4xx0
40 - 63 A modular contactor - 4 pole
•
•
NO and NC contact gap ≥ 3 mm, double break
Continuous duty for the coil and contacts
•
•
•
AC/DC silent coil (with varistor protection)
Protective separation (reinforced insulation) between coil and contacts
Mechanical indicator as standard
•
•
•
AgSnO
2 contacts
Compliant with EN 61095: 2009 and with
EN 60947-4-1: 2009
35 mm rail (EN 60715) mount
•
•
For high inrush current loads
176 A
Contact material AgSnO
2
•
•
Specifically intended: for high inrush current loads
240 A
Contact material AgSnO
2
22.44.../22.64...
Screw terminal
22
SERIES
4 NO
(4310)
3 NO + 1 NC
(4710)
2 NO + 2 NC
(4610)
For outline drawings see page 8
Contact specification
Contact configuration
Rated current/Maximum peak current A
Rated voltage V AC
Rated load AC1 / AC-7a (per pole @ 250 V) VA
Rated current AC3 / AC-7b (400 V) A
Rated load AC15 (per pole @ 230 V) VA
Three-phase motor rating (400 - 440 V AC) kW
Rated current AC-7c A
230 V lamps rating: incandescent or halogen W compact fluorescent (CFL) W electronic ballast fluorescent tubes W electromagnetic ballast compens. fluorescent tubes W
Breaking capacity DC1: 30/110/220 V A
Minimum switching load mW (V/mA)
Contact material
Coil specification
Nominal voltage (U
N
) V DC/AC (50/60 Hz)
Rated power AC/DC VA (50 Hz)/W
Operating range DC/AC (50/60 Hz)
Holding voltage
Must drop-out voltage
Technical data
DC/AC (50/60 Hz)
DC/AC (50/60 Hz)
Mechanical life AC/DC
Electrical life at rated load AC-7a
Operate/release time cycles cycles ms
Insulation between coil and contacts (1.2/50 μs) kV
Ambient temperature range °C
Protection category
Approvals (according to type)
4 NO, (or 3NO + 1NC or 2NO + 2NC) ≥ 3 mm
40 / 176
250 / 440
16,000
22
—
11
—
4,000
1,000
1,500
1,500
40/4/1.2
1,000 (17/50)
AgSnO
2
63 / 240
250 / 440
24,000
30
—
15
—
5,000
1,500
2,000
2,000
63/4/1.2
1,000 (17/50)
AgSnO
2
12 - 24 - 110...120 (110 V DC) - 230...240 (220 V DC)
5
(0.85…1.1) U
N
0.85 U
N
0.2 U
N
5
(0.85…1.1) U
N
0.85 U
N
0.2 U
N
3 · 10
100 · 10
20 / 45
6
–5…+55
IP20
6
3
3 · 10
6
IP20
6
100 · 10
20 / 45
–5…+55
3
3
22
SERIES
22 Series - Modular contactors 25 - 40 - 63 A
Ordering information
Exemple: 22 series, modular contactor 25 A, 4 NO contacts, coil 230 V AC/DC, AgSnO
2 contacts, Auto-On-Off selector + mechanical indicator + LED.
A B C D
2 2
.
3 4
.
0
.
2 3 0
.
4 3 4 0
Series
Type
3 = 25 A modular contactor range
4 = 40 A modular contactor range
6 = 63 A modular contactor range
Number of contacts
2 = 2 pole
4 = 4 pole
Coil version
0 = AC (50/60 Hz)/DC
Coil rated voltage
See coil specifications
D: Special versions
0 = Standard
C: Options
1 = Mechanical indicator
2 = Mechanical indicator + LED
4 = Auto-On-Off selector + mechanical indicator + LED
B: Contact circuit
3 = All NO contacts
4 = All NC contacts (22.32 only)
5 = 1 NO + 1 NC
6 = 2 NO + 2 NC
7 = 3 NO + 1 NC
A: Contact material
1 = AgNi
4 = AgSnO
2
Selecting features and options: only combinations in the same row are possible.
Preferred selections for best availability are shown in bold.
Type
22.32
22.34
22.44
22.64
Coil version
AC/DC
AC/DC
AC/DC
AC/DC
A
4
4
1 - 4
1 - 4
B C
3 - 4 - 5 2 - 4
3 - 6 - 7 2 - 4
3 - 6 - 7 1
3 - 6 - 7 1
D
0
0
0
0
Options
Auto-On-Off selector + mechanical indicator + LED (xx40 option)
Type 22.32 / 22.34
1
1
Options
Selector
The three-position manual selector has the following functions:
• ON position - the contacts are latched in the operated state
(NO contacts - closed and NC contacts - open), the mechanical indicator is visible in its window, the LED is not illuminated.
2
3
2
• AUTO position - the state of contacts, mechanical indicator and LED follow the coil supply voltage.
• OFF position - even if terminals A1 - A2 are supplied with rated voltage, the coil is not energized, and so the contacts remain in the non-operated state, the mechanical indicator is not visible and the LED is not illuminated.
LED
Type 22.44 / 22.64
3
1
Mechanical indicator
Options
Mechanical indicator
1
4
22 Series - Modular contactors 25 - 40 - 63 A
Technical data
Insulation
Rated insulation voltage
Pollution degree
Insulation between coil and contact set
V AC 250
3 *
22.32 / 22.34
440
2
Type of insulation
Overvoltage category
Rated impulse voltage
Dielectric strength
Insulation between adjacent contacts
Type of insulation kV (1.2/50 μs)
Reinforced
III
6
V AC 4,000
Overvoltage category
Rated impulse voltage
Dielectric strength
Insulation between open contacts
Basic
III kV (1.2/50 μs) 4
V AC 2,500
NO contact
Contact gap
Overvoltage category
Rated impulse voltage mm 3
III kV (1.2/50 μs) 4
NC contact
1.5
II
2.5
Dielectric strength V AC/kV (1.2/50 μs) 2,500/4 2,000/3
* Only for versions without Auto-On-Off selector. For versions with Auto-On-Off selector pollution degree 2 applies.
Conducted disturbance immunity Reference standard
Fast transients (burst 5/50 ns, 5 kHz) at coil terminals EN 61000-4-4
Voltage pulses (surge 1.2/50 μs) at supply terminals (differential mode) EN 61000-4-5
Short circuit protection
Rated conditional short circuit current
Back-up fuse
Terminals
Max. wire size – contact terminals
Max. wire size – coil terminals kA
A
22.32 / 22.34
3
32 (gL/gG type) mm 2
22.32 / 22.34
mm 2 1 x 6 / 2 x 4
AWG 1 x 10 / 2 x 12
1 x 4 / 2 x 2.5
Level 4 (4 kV)
Level 4 (4 kV)
22.44
3
63
Solid and stranded cable
440
3
Reinforced
III
4
2,000
Basic
III
4
2,000
NO/NC contacts
3
III
4
2,000/3
Level 2 (2 kV)
Level 2 (2 kV)
22.64
3
80
22.44 / 22.64
22.44 / 22.64
1x25 (solid) - 1x16 (stranded)
1x4 (solid) - 1x6 (stranded)
1x2.5
Min. wire size – contact and coil terminals
Screw torque
Wire strip length
Power lost to the environment
AWG 1 x 12 / 2 x 14 mm 2 1 x 0.2
AWG 1 x 24
Nm 0.8
mm 9
22.32
without contact current W 2 with rated current W 4.8
22.34
2
6.3
1x14
1x1 (coil) - 1x1.5 (contacts)
1x18 (coil) - 1x16 (contacts)
1.2 (coil terminals) - 3.5 (contact terminals)
10
22.44
5
17
22.64
5
37
NOTE
22.32/22.34: It is suggested an air gap of 9 mm between adjacent relays for installations and working conditions close to the limit (that is, ambient temperature > 40 °C, coil operated for a prolonged period of time, all contacts loaded with current > 20 A).
22.44/22.64: The maximum ambient temperature with 3 adjacent contactors is + 40 °C; when more than 3 contactors are installed, it is necessary an air gap of 9 mm.
With 2 adjacent contactors the maximum ambient temperature is + 55 °C; when more than 2 contactors are installed, it is necessary an air gap of 9 mm.
22
SERIES
5
22
SERIES
22 Series - Modular contactors 25 - 40 - 63 A
Contact specification
Ratings and utilization categories according to EN 61095: 2009
Type
AC-7a
Rated current Rated electrical
(A) life (Cycles)
22.32….1xx0 (AgNi contacts)
22.32….4xx0 (AgSnO
2
22.34….1xx0 (AgNi contacts)
22.34….4xx0 (AgSnO
2
22.44….4xx0
22.64….4xx0
contacts) contacts)
25
25
25
25
40
63
70·10 3 (NO)
30·10 3 (NC)
30·10 3
150·10 3
100·10 3
(NO)
(NC)
30·10 3
100·10 3
100·10 3
Utilization category
AC-7b AC-7c
Rated current Rated electrical Rated current Rated electrical
(A) life (Cycles) (A) life (Cycles)
10
10
10
10
22
30
Utilization category: AC-7a = Slightly inductive loads (cos ϕ=0.8)
AC-7b = Motor loads; (cos ϕ=0.45, I making
= 6xI breaking
)
AC-7c = Compensated electric discharge lamps (cos ϕ=0.9, C= 10 mF/A)
30·10 3
30·10 3
30·10 3
30·10 3
150·10 3
150·10 3
—
10
—
10
—
—
—
30·10 3
—
30·10 3
—
—
H 22 - Maximum DC1 breaking capacity - Type 22.32 / 22.34
H 22 - Maximum DC1 breaking capacity - Type 22.44 / 22.64
type 22.64
type 22.44
DC voltage (V) DC voltage (V)
• When switching a resistive load (DC1) having voltage and current values under the curve, an electrical life of ≥ 100·10
3 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.
Coil specifications
AC/DC version data (type 22.32)
Nominal voltage
U
N
V
12
24
48
60
120
(110...125)
230
(230...240 AC)
(220 DC)
Coil code
0.012
0.024
0.048
0.060
0.120
0.230
Operating range
U min
V
9.6
19.2
38.4
48
88
184 (AC)
176 (DC)
U max
V
13.2
26.4
52.8
66
138
264 (AC)
242 (DC)
Rated coil consumption
I
N at U
N
(AC) mA
165
83
42
33
16.5
8.7
AC/DC version data (type 22.44 / 22.64)
Nominal voltage
U
N
V
12
24
120
Coil code
0.012
0.024
0.120
Operating range
U min
V
10.2
20.4
102
U max
V
13.2
26.4
138
(110...125)
230
(230...240 AC)
0.230
196
264 (AC)
(220 DC)
242 (DC)
I
Rated coil consumption
N at U
N
(AC) mA
417
208
41
21
AC/DC version data (type 22.34)
Nominal voltage
U
N
V
12
24
48
60
120
(110...125)
230
(230...240 AC)
(220 DC)
Coil code
0.012
0.024
0.048
0.060
0.120
0.230
Operating range
U min
V
9.6
19.2
38.4
48
88
184 (AC)
176 (DC)
U max
V
13.2
26.4
52.8
66
138
264 (AC)
242 (DC)
R 22 - Coil operating range v ambient temperature
Rated coil consumption
I
N at U
N
(AC) mA
165
83
42
33
16.5
8.7
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
6
Wiring diagrams
22 Series - Modular contactors 25 - 40 - 63 A
22
SERIES
Line and neutral switched Line only switched
Type 22.32
Line and neutral switched
Type 22.34
Type 22.34
Line only switched
Type 22.44 / 22.64
Type 22.44 / 22.64
7
22
SERIES
Outline drawings
Type 22.32
Screw terminal
22 Series - Modular contactors 25 - 40 - 63 A
Type 22.32 + 022.33 / 022.35
Screw terminal
Type 22.34
Screw terminal
Type 22.34 + 022.33 / 022.35
Screw terminal
Type 022.33 / 022.35
Screw terminal
Type 22.44 / 22.64
Screw terminal
8
22 Series - Modular contactors 25 - 40 - 63 A
Auxiliary module 022.33 / 022.35 for 22.32 and 22.34 only
022.33
022.35
22
SERIES
22.32 + 022.33 / 022.35
22.34 + 022.33 / 022.35
Contact specification
Contact configuration 2 NO
Conventional free air thermal current I th
Rated current AC15 (230 V)
A 6
VA 700
Electrical life at rated load cycles 30 x 10 3
Contact material AgNi
Short circuit protection
Rated conditional short circuit current kA 1
Back-up fuse
Terminals
Max. wire size
A 6 (gL/gG type)
Solid and stranded cable
Min. wire size mm 2 1 x 4 / 2 x 2.5
AWG 1 x 12 / 2 x 14 mm 2 1 x 0.2
Screw torque
Wire strip length
Power lost to the environment
without contact current with rated current
AWG 1 x 24
Nm 0.8
mm 9
W
W
—
0.5
Approvals (according to type)
NOTE: it is not possible to assembly the auxiliary module on 22.32.0.xxx.x4x0 (2 NC versions).
1 NO + 1 NC
6
700
30 x 10 3
AgNi
9
22
SERIES
Accessories
22 Series - Modular contactors 25 - 40 - 63 A
Adaptor for panel mounting (for 22.32 type), plastic, 17.5 mm wide
020.01
020.01
Adaptor for panel mounting (for 22.34 type), plastic, 35 mm wide
011.01
011.01
Sheet of marker tags, plastic, 72 tags, 6x12 mm 060.72
060.72
019.01
Identification tag, plastic, 1 tag, 17x25.5 mm
019.01
Separator for rail mounting, plastic, 3 mm wide
020.03
020.03
022.18
U
RO
P A
AN
P E A N
T E
PE
N T
RO
8-way jumper link for types 22.32, 17.5 mm wide
Rated values
022.18 (blue)
10 A - 250 V
022.26
U
RO
P E A N
P A
AN
T E
PE
N T
RO
6-way jumper link for types 22.34, 35 mm wide
Rated values
022.26 (blue)
10 A - 250 V
10
advertisement
Key Features
- Continuous duty for the coil and contacts
- AC/DC silent coil (with varistor protection)
- Protective separation (reinforced insulation) between coil and contacts
- Mechanical and LED indicators as standard
- Auto-On-Off selector version available
- AgNi and AgSnO2 contact versions available
- Auxiliary contact module available, quick-assembly with the main contactor
- 35 mm rail (EN 60715) mount
- Compliant with EN 61095: 2009 and with EN 60947-4-1: 2009
Frequently Answers and Questions
What are the contact materials available for these contactors?
What are the different types of contact configurations available?
What is the rated current for these contactors?
Related manuals
advertisement