Hifonics BE35 1700.1D Brutus Elite Amplifier Owner Manual

Add to my manuals
2 Pages

advertisement

Hifonics BE35 1700.1D Brutus Elite Amplifier Owner Manual | Manualzz
Before you start
4 Chassis Ground
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
The chassis ground connection
is critical to the performance
of the amplifier. Choose a
location that is close to the
amplifier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Model
Fuse Size
Cable Size
BE35-500.4
2x25A ATC
4ga
BE35 800.4
2x35A ATC
4ga
BE35 1200.1D
1 x 80A Maxi
4ga
BE35 1700.1D
2 x 70A Maxi
2ga
Be sure to use the proper fuse size
for each model. Some models require
an external fuse.
BE35 2100.1D External 200A
0ga
BE35 2500.1D External 250A
0ga
External 100A
2ga
BE35 5000.5
1 Disconnect
negative battery
terminal
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
2 Run Cables
3 Mount Amplifier
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplifier to
a secure surface. Do not mount
the amplifier upside down.
SPEAKER
OUTPUT
OUTPUT
Stereo
SPEAKER
OUTPUT
Bridged
BRIDGED
BRIDGED
BRIDGED
CH 2
CH 1
RIGHT
LEFT
BRIDGED
RIGHT
CH 4
CH 3
5 Negative Power
BRIDGED
BRIDGED
LEFT
Attach the chassis ground
cable to the amplifier
negative terminal. It is
important to make sure this
connection is very tight.
RIGHT
SPEAKER
SPEAKER
CH
4
SPEAKER
CH 3
OUTPUT
OUTPUT
SPEAKER
OUTPUT
BRIDGED
6
Monoblock
Remote Turn-on
Connection
Attach the remote turn on
wire to the amplifier remote
output of the source unit.
LEFT
SPEAKER
OUTPUT
LEFT
CH 4
CH 3
BRIDGED
BRIDGED
BRIDGED
RIGHT
OUTPUT
SPEAKER
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
OUTPUT
SPEAKER
LEFT
RIGHT
CH 1
OUTPUT
OUTPUT
SPEAKER
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
CH 2
Monoblock
OUTPUT
OUTPUT
BRIDGED
LEFTSPEAKER
SPEAKER
SPEAKER
multiple woofers
RIGHT OUTPUT
OUTPUTOUTPUT
CH 3
CH 4
Positive Power
Connection
Attach the main power cable
to the amplifier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
RIGHT
11 Positive Battery
OUTPUT
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
BRIDGED
CH 4
CH 3
OUTPUT
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Connection
9 Level Control
SPEAKER
Connection
8 Signal Input
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplifier.
OUTPUT
CH 4
CH 3
CH 2
CH 1
SPEAKER
BRIDGED
BRIDGED
BRIDGED
LEFT
12 Re-connect
SPEAKER
Negative Battery
Terminal
OUTPUT
Turn the LEVEL control completelyINPUT
counter-clockwise to minimum. LEVEL
INPUT
LEVEL
MODE
XOVER
SUBSONIC SUBSONIC Re-connect the negative
battery terminal making sure it
is securely tightened.
FULL
9V
0.2V
PHASE
6V
0.2V
LPF
15
35Hz
LPF
10
40Hz
LPF
LP
HP
XOVER
MONO STEREO
MODE
SPEAKER
OUTPUT
BRIDGED
7
OUTPUT
BRIDGED
single woofer
SPEAKER
OUTPUT SPEAKER
BRIDGED
CH 4
CH 2
CH 1
RIGHT
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
CH 3
SPEAKER
Properly route power,
speaker and RCA cables
through the vehicle.
CH 4
Bare metal
BRIDGED
Installation
BRIDGED
CH 3
Connect the speaker cables to
the speaker output connectors.
SPEAKER
OUTPUT
Follow the diagram below
that best fits your speaker
configuration.
SPEAKER
Connection
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplifier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Connections
RIGHT
LEFT
Power cable size
and fusing
10 Speaker
BRIDGED
LEFT
SPEAKER
BASS EQ
Input Mode
0
10dB
B
Xover Mode
35
250Hz
High pass
Adjustment
250Hz
40
300Hz
0
9V
9dB
0.2V
60
FULL
1.3KHz 60 1.2KHz
6V 9V 0.2V
0.2V 156V 35Hz
0.2V 10 15 40Hz35Hz
The XOVER Mode switch sets the type
of crossover
4
channelLPFLPF
PHASE that will
LPFbe active.
LPF
PHASE
LPF
models will have two switches, one for each
set of channels.
180
350
250Hz
180
30 35 250Hz
250Hz 40 30300Hz
250Hz
D
Low pass
Adjustment
MONO
STEREO
FULL LPF
HPF
E
Bass Boost
300Hz
LPF4CH
1.2KHz
6V
0.2V
LPF
LPF
LPF
60Hz1
LPF
FULL LPFH PF
SPEAKER
60Hz1
.2KHz
30
10dB
0
60
9dB
0
LPF
250Hz
12dB
SPEAKER
40
300Hz
40Hz
60
60
1.2KHz
250Hz
HP
60Hz1
.2KHz
This is a critical step to insure your amplifier
INPUT
is properly adjusted to match the signal LEVEL
output level of your source unit.
INPUT
LEVEL
9V
0.2V
6V
1.5Hz
OUTPUT
XOVER
SPEAKER
CH 3
BRIDGED
BASS EQ SPEAKERHPF
LEVEL
BRIDGED
LEFT
MODE
SUB
SONIC
SPEAKER
OUTPUT
CHLEFT
1
RIGHT
6V
0.2V
SPEAKER
OUTPUT
CH 4
1.
If possible, with the source unit off, confirm that the primary volume control is
PHASE
LPF
turned down (counter clockwise).
2.
Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is
turned down. Make sure the source unit controls; balance,
fader,
bass35and250Hz
0
180
treble are all set to center or “0” adjustment. Make sure that the green LED on
the end of the amplifier is illuminated.
BASS CD
EQ is preferred.
BASS EQ
Play a clean musical selection of which you are very familiar.
15
35Hz
LPF
30
250Hz
HPF
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
0
10dB
0
9dB
4.
Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5.
Increase the amplifier level (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple amplifiers.
60
1.3KHz
OUTPUT
10
OUTPUT
RIGHT
SPEAKER
Quick Start
Installation Guide
OUTPUT
0
12dB
BRIDGED
BRIDGED
60
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
LPF
OUTPUT
BRIDGED
CH
2
RIGHT
1.2KHz
30
BRIDGED
BRIDGED
LEFT
250Hz
RIGHT
LEFT
CH 4
CH 3
RIGHT
CHANNEL 3/4
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
OUTPUT
OUTPUT
SPEAKER
SPEAKER
OUTPUT
OUTPUT
SPEAKER
SPEAKER
OUTPUT
OUTPUT
SPEAKER
MODE
OUTPUT
LEVEL
SPEAKER
BASS EQ
LEVEL
4CH
6V
SPEAKER
BRIDGED
BRIDGED
HPF
CH 3
LEFT
CH 4
RIGHT
2CH
0.2V
6V
OUTPUT
SPEAKER
0.2V
0
OUTPUT
12dB
60
CHANNEL
SPEAKER3/4
SPEAKER
LPF
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
1.2KHz
30
10
40Hz
CH 2
250Hz
OUTPUT
OUTPUT
SPEAKER
OUTPUT
LPF
40
XOVER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BE35 500.4
BE35 2100.1D
BE35 800.4 BE35 2500.1D
BE35 1200.1D BE35 5000.5
BE35 1700.1D
SPEAKER
300Hz
CH 3
MODE
OUTPUT
BRIDGED
CH 1
OUTPUT
BRIDGED
OUTPUT
SPEAKER
LEFT
LOW
PASS
X-OVER
SUBSONIC
SUBSONIC SUBSONIC
0.2V
OUTPUT
OUTPUT
CH 4
CH 3
CH 4
SPEAKER
OUTPUT
BRIDGED
RIGHT
HPF
MONO STEREO
X-OVER
12dB
Mono
1/2
MONO STEREO
OUTPUT
STEREO
FULL
LPF HPF 15Hz MONO
HPF
HPF 50Hz
LPF FULL
300Hz LPF FULL
35Hz
35Hz2
0
MODE
SPEAKER
SPEAKER
OUTPUT
MODE
0.2V
1.2KHz
OUTPUT CHANNEL
XOVER
LP
6V
LOW
PASS
MODE
1.3KHz
SPEAKER
OUTPUT
OUTPUT
SPEAKER
BRIDGED
HPF LPF FULL
SPEAKER
XOVER
40Hz
CH 4
CH 3
X-OVER
HPF LPF FULL
CHANNEL 1/2
OUTPUT
30Hz
LEVEL Mono
4ch - Mixed
10
LPF
SPEAKER
SPEAKER
SPEAKER
.2KHz
HPF
OUTPUT
30Hz BRIDGED
1.5Hz
X-OVER
FULL
30Hz 1.5Hz 40Hz 300Hz
180
35
250Hz
OUTPUT
OUTPUT
BRIDGED
CH 2
SPEAKER
THIS IS NOT A VOLUME CONTROL!
3.
1.5Hz
EQ
4CHBASS2CH
CH 4 1.2KHz
60
CH 3
Level Setting
.5KHz
MODE
15BRIDGED35Hz
FULL LPFBRIDGED
HPF
G
10Hz1
MONO STEREO
MODE
2CH
HPF
30 CH 3250Hz
30
Remote Level
Control
30Hz
XOVER LEFT
2CH 3CH 4CH
OUTPUT
SPEAKER
FULL LPFH PF
.5KHz
The Bass EQ control will increase the power
2CH 3CH 4CH
HPF
HPF
BASS EQ BASS EQ
output at 45Hz for more pronounced bass.
Exercise caution when using this control. BRIDGED
LPF BRIDGED CHHPF
BASS EQ
2
CH 1
LEFT
RIGHT
Increase the level in small amounts until
distortion is noticed, then back off a little.
Some models include a bass
remote. Avoid adjusting the bass
remote while operating vehicle.
BRIDGED
CH 1
RIGHT
HPF
LPF
XOVER
SPEAKER
SUBSONIC SUBSONIC
OUTPUT
0
F
10Hz1
MODE
60
LPF
PHASE
0
MODE
HPF
HPF
INPUT
LEVEL
RIGHT
SPEAKER
LEFT
FULL LPFH PF
.5KHz
HPF
FULL LPF HPF
9VBRIDGED0.2V
The LPF(low pass filter) control
will limit output above the selected
frequency. This is used to allow
a smooth transition to the higher
frequency speakers.
MONO STEREO
10Hz1
MODE
XOVER
TheBASS
HPF(high
limitHPF
the
HPF will
EQ pass
BASSfilter)
EQEQ control
HPF
BASS
EQ This
output below the BASS
selected
frequency.
INPUT
LEVEL
is typically used to protect midrange and hi
frequency speakers from damage and to
60 1.3KHz 60 1.2KHz
10dB
0
9dB from
allow0 a smooth
transition
60 1.3KHz
0
10dB
0 a subwoofer.
9dB
LEFT
MONO
FULL STEREO
HP
LP
XOVER
LPF
40
SPEAKER
SPEAKER
SPEAKER
BRIDGED
XOVER
HPF
HP
OUTPUT
OUTPUT
4ch - Full Range
MODE
MODE
XOVER
10 LP 40Hz
SPEAKER
SPEAKER
OUTPUT
OUTPUT
Common System Setup
MONO STEREO
FULL LPF HPF
The MODE switch will sum or combine the right
MODE
and left
channel signals
2CH position to
XOVER
INPUT
INPUT
INPUT in the
HPF
HPFINPUT
BASS
EQ
improve
bass performance
when
bridging
the
SUBSONIC
SUBSONIC
SUBSONIC
LEVEL
LEVEL
LEVEL SUBSONIC
LEVEL
amplifier to mono. Use the 4CH mode when
driving four full range speakers.
4CH
2CH
0
C
30
SPEAKER
SPEAKER
CH 3/4
A
180
OUTPUT
CH 3/4
0
SPEAKER
CH 3/4
Setup
MODE
XOVER
LPF
CH 1/2
LPF
CH 3/4
LPF
CH 1/2
PHASE
CH 4
OUTPUT
The information
within this document is intended to offer some
SPEAKER basic guidelines
OUTPUT
MONO STEREO
FULL
HP contained
for a few
LP of the most common installations. More complex audio systems should be
installed by a competent professional. Additional installation information available at
www.maxxsonics.com
MODE
XOVER
40Hz
LPF
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
MONO workmanship
STEREO
LPF HPF and
defectsFULL
in material
for a period of one (1) year from the date of purchase.
40
300Hz
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components thatMODE
prove to be defective in materials and workmanship under proper installation
HPFand use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
4CH is limited
2CH
USA Inc. This warranty
to defective parts and specifically excludes any incidental or
60 1.2KHz
consequential damages connected therewith. To view the full warranty, please visit the website.
Hifonics products are designed and engineered in the USA by
847-540-7700
www.maxxsonics.com
HF BE35 2015 QSG 01 - rev1
Congratulations on your choice of a Hifonics amplifier.
This “Quick Start Installation” guide is meant to help you
“hook up” and play music. For more detailed information,
on system setting, speaker and subwoofer configuration
and full specifications by model visit the website,
http://hifonics.com/manuals.html

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement