Hoffman Syspend Sanitary HMI Fixed Coupling Instruction manual

Below you will find brief information for Syspend 89042760, Syspend 89042837. This document provides installation instructions for the Syspend product, including steps for installing the tube/sleeve into the fitting. It describes how to secure the sleeve and position o-rings. The instructions also highlight the importance of tightening the nut carefully to avoid pinching the o-ring. The document also includes a cutout template that should be printed to scale.

PDF

Document

Syspend
Rev. J
&copy; 2019 Hoffman Enclosures Inc.
PH 763 422 2211 • nVent.com/HOFFMAN
P/N 89042760
89042837
NOTE:
Cutout template must be printed at
1:1 scale. Measure after printing to
verify dimensions.
-2-
&copy; 2019 Hoffman Enclosures Inc.
PH 763 422 2211 • nVent.com/HOFFMAN
89042837
&gt;@
&gt;@
[
[
[
[
[
0;0066
[
1
[
[
0
[
1(0$7&lt;3(;
66
[
2
-3-
&copy; 2019 Hoffman Enclosures Inc.
PH 763 422 2211 • nVent.com/HOFFMAN
89042837
3
4
a. Install tube/sleeve into fitting. Be sure
safety screw is fully seated in fitting
cutout.
b. Push sleeve down into fitting until it is
tight.
c. Be sure top surface of sleeve is
aligned at split, or left side is lightly
lower than right.
d. Place o-rings in position dry.
Lube top surface only of both o-rings (the
surface the nut will contact)
1P
OEIW
7LJKWHQQXWVORZO\DQGZDWFKIRU
DQ\SDUWPRYHPHQWVWKDWPD\SLQFK
WKHRULQJ
r
-4-
5
r
&copy; 2019 Hoffman Enclosures Inc.
PH 763 422 2211 • nVent.com/HOFFMAN
89042837
">

Hello! I have reviewed the Installation Manual for the Syspend models 89042760 and 89042837. This document provides detailed steps for installation, including fitting and sleeve setup, o-ring placement, and nut tightening. I'm ready to answer any questions you have about the installation process or features described in the manual.

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Fitting installation
Sleeve securing
O-ring placement
Nut tightening guidance
Cutout template for installation

Frequently asked questions

Ensure the safety screw is fully seated in the fitting cutout.

Push the sleeve down into the fitting until it is tight.

Place the o-rings in position dry.

Lube the top surface only of both o-rings (the surface the nut will contact).

Watch for any part movements that may pinch the o-ring.

What should I do before installing the tube/sleeve?

How should the sleeve be pushed into the fitting?

Where should the o-rings be placed?

What part of the o-ring needs lubrication?

What should I watch for when tightening the nut?

Related

Sequestr 89169292, 89169294 Disconnect Enclosure Installation Manual

Sequestr 87924206, 87924207 Installation Manual

Installation of 89042715, 89042836 Suspension system

Nvent ProLine G2 Frame Joining Kit Instruction manual

Lay-In Wireway Installation Instructions

Hoffman Sequestr Low-Amp External Disconnect, Type 4, 12 and 3R Instruction manual

Nvent ProLine G2 Vented Gland Plate Instruction manual

Nvent Pull-Out Shelf for Mini Keyboard Instruction manual

PROLINE APX CONCEPT Support Bracket Installation Manual

Nvent ProLine G2 Frame Joining Kit Instruction manual

Nvent Industrial Workstation Instruction manual

Nvent Syspend 281-Max 48-mm Round Tube Flange Coupling and Adapter Instruction manual