Federal Signal PAR46 Unity LED Spot Light Product Manual

Federal Signal PAR46 Unity LED Spot Light Product Manual

Below you will find brief information for LED Spot Lamp 380400-W LED Clear Spot Lamp. The 380400-W LED Clear Spot Lamp is designed to provide higher warning visibility on the road. It can be used in a variety of applications.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Federal Signal LED Spot Lamp 380400-W LED Clear Spot Lamp Installation Instructions | Manualzz

Installation Instructions for the Model

380400-W LED Clear Spot Lamp

25500065A REV. A 313

Safety Message to Installers of Warning Light Equipment

People’s lives depend on your safe installation of our products. It is important to read, understand and follow all instructions shipped with the products. Listed below are some other important safety instructions and precautions you should follow:

• Do not install equipment or route wiring in the deployment path of an airbag.

• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if the seat needs to be recalibrated for proper airbag deployment.

• Locate the light control so the VEHICLE and CONTROL can be operated safely under all driving conditions.

• You should frequently inspect the light system to ensure that it is operating properly and that it is securely attached to the vehicle.

• To be an effective warning device, this product produces bright light that can be hazardous to your eyesight when viewed at close range. Do not stare directly into this lighting product at close range or permanent damage to your eyesight may occur.

• When drilling into a vehicle structure, be sure that both sides of the surface are clear of anything that could be damaged.

• File these instructions in a safe place and refer to them when maintaining and/or reinstalling the product.

Product Overview

The Model 380400-W LED Spot Lamp is designed to provide a higher warning visibility on the road. It can be used in a variety of applications.

Unpacking the Lamp

After unpacking the lamp, inspect it for damage that may have occurred in transit. If it has been damaged or is missing a part, do not attempt to install or operate it. File a claim immediately with the carrier, stating the extent of the damage. Carefully check all envelopes, shipping labels and tags before removing or destroying them.

Ensure that all parts in Table 1 on page 2 have been included. If you are missing any parts, contact Customer

Support at 1-800-264-3578, 7 a

.

m

. to 5 p

.

m

., Monday through Friday (CT).

Installing the Lamp on the Vehicle

To install the lamp:

1. Determine the mounting locations for the spot lamp and for an installer-supplied control switch.

2. Route an 18 AWG wire from the +12 V power source to the location of the switch. Install an installersupplied 5 A fuse and fuse holder as close to the power source as possible.

3. Use a Phillips screwdriver to loosen the gray screw (+12 V) and the black screw (-NEG) on the back of the lamp.

4. Route an 18 AWG wire from the control switch to the location of the spot lamp. Wrap the stripped end of the wire clockwise around the gray screw and tighten the screw.

Installation Instructions for the Model 380400-W LED Clear Spot Lamp

5. Wrap the stripped end of an 18 AWG wire clockwise around the black screw and tighten the screw. Connect the wire to a convenient chassis ground. The battery is recommended.

6. Check the wiring and test the spot lamp for proper operation.

Getting Technical Support and Service

For technical support and service, please contact:

Service Department

Federal Signal Corporation

Phone: 1-800-433-9132

Fax: 1-800-343-9706

Email: [email protected]

Returning a Product to Federal Signal

Before returning a product to Federal Signal, call 800-264-3578, 800-433-9132, or 800-824-0254 to obtain a

Returned Merchandise Authorization number (RMA number). To expedite the process please be prepared with the following information:

• Your Federal Signal customer or account number.

• The purchase order number under which the items were purchased.

• The shipping method.

• The model or part number of the product being returned.

• The quantity of products being returned.

• Drop ship information as needed.

• Any estimate required.

When you receive your RMA Number:

• Write the RMA number on the outside of the box of returned items.

• Reference the RMA number on your paperwork inside of the box.

• Write the RMA number down, so that you can easily check on status of the returned equipment.

Send all material with the issued RMA Number to:

Federal Signal Corporation

Public Safety Systems

2645 Federal Signal Drive

University Park, IL 60484-3167

Attn: Service Department

RMA: #__________

800-433-9132

800-343-9706 (fax) www.fedsig.com

advertisement

Key Features

  • Higher warning visibility
  • Variety of applications
  • Easy installation
  • Durable construction
  • Bright LED light
  • Reliable performance

Frequently Answers and Questions

What is the purpose of the 380400-W LED Clear Spot Lamp?
The 380400-W LED Clear Spot Lamp is designed to provide a higher warning visibility on the road. It can be used in a variety of applications.
How do I install the 380400-W LED Clear Spot Lamp?
The installation instructions are provided in the document. You will need to determine the mounting locations, route wiring, connect the lamp to a power source, and test the lamp for proper operation.
What if I am missing parts or the lamp is damaged?
Do not attempt to install or operate the lamp if it has been damaged or is missing a part. File a claim immediately with the carrier, stating the extent of the damage. Contact Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m., Monday through Friday (CT).

Related manuals

Download PDF

advertisement