Sno–Konette
Instruction Manual
Deluxe – Model #1002, 1002EX
Standard – Model #1003, 1003EX
Part No. 22045
Revised May 2002
Model #1003 and 1003EX
Model #1002 and 1002EX
Cincinnati, OH 445241-4807 USA
Sno-Konette
Safety Precautions
2 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
INSTALLATION
MACHINE DESCRIPTION
The Sno-Konette is an automatic shaver with a tremendous capacity. You will find that it keeps up with any demand; as soon as you put ice into the hopper, it is shaved into small ice chips. The Sno-Konette consists of the hopper, which houses the cutter head, the pusher handle, the motor, and the display case.
ELECTRICAL REQUIREMENTS
The Sno-Konette operates on 120 Volt, 15 Amp, single phase, 60 cycle AC current. The Sno-Konette
Export operates on 230 Volt, 50 cycle. Models are available in a 12 volt DC version. Be sure that your electrical supply meets this requirement.
ICE REQUIREMENTS
The Sno-Konette can take ice cubes or block ice, if you break the block into pieces approximately 3 to 4 inches in size.
NOTE: The ice will not enter the shaving chute if the pieces are too large.
MACHINE OPERATION
After unpacking the Sno-Konette you should locate the pusher handle (packed in a seperate box). Connect the pusher handle to the shaver body. Plug the power cord into the appropriate electrical outlet.
TO OPERATE THE SNO-KONETTE
1. Fill the hopper to within an inch of the top with ice cubes or block ice (no larger than 3" to 4"). The larger the pieces, the better the snow.
2. Switch the motor on. Wait for the motor to come to full speed (a minute or so).
3. Push the pusher handle down against the ice in the hopper. Apply firm and even pressure to make the best snow. Practice will allow you to gauge when to stop pressing. This allows the ice to resettle against the shaver head. You may find that you need to relieve the pressure two or three times in a cycle. Too much pressure will result in snow that is coarse; too little pressure will make the snow mushy.
NOTE: Never allow any foreign or metallic objects around the shaver area of the Sno-Konette. Ice picks, scoops, and debris that may be in the ice often damage blades.
3 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
MAINTENANCE INSTRUCTIONS
4 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
ORDERING SPARE PARTS
1. Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity desired.
3. Please include your model name and machine serial number (located on the machine nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 or, place orders at:
(513) 769-7676
Fax: (513) 769-8500
E-mail: [email protected]
5 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
INSTALLING NEW SHAVER BLADES
Inspect your equipment before replacing the blades. Use a flashlight to examine the blades in the shaver body. If the blades appear to be nicked or bent, then the blades should be replaced.
Follow this procedure:
1. Unplug the main power supply cord from the electrical outlet.
2. Remove the shaver head from the motor shaft by loosening the Allen head set screws (2) between the motor and the hopper.
3. Remove the shaver head. Pull the shaver head off of the motor shaft and through the hopper. If the shaver head is frozen onto the shaft, remove the hold down bolts on the motor. Pull the motor back, trapping the shaver head against the inside of the hopper, until the shaver head disengages.
4. After removing the shaver head, check the motor shaft for burrs and corrosion. Use a fine tooth file to remove the burrs and corrosion.
5. Remove the blades from the shaver head. These blades may be resharpened, but it is far better to replace the old blades with a new set.
6. Position the new blades and insert screws until they are finger tight.
7. Set the blade thickness equal to a dime. (See illustration below.) Make sure that the height is even across the shaver head.
8. Tighten the blade screws completely. Check the blades again with a dime to ensure the blades did not move while tightening the screws.
9. Replace the motor and shaver head. Mount the motor using the hold down bolts. Insert the shaver head through the hopper and onto the motor shaft. Press the shaver head onto the motor shaft with the pusher handle, then move the shaver head in another 1/8". Check that the shaver head is not rubbing against the back of the hopper and the blades are not touching the pusher handle.
10. Replace the set screws (2) between the hopper and the motor.
NOTE:
Replace the shims that were between the motor base and the mounting surface.
SET TOP OF BLADE
FLUSH WITH HEIGHT
GAGE, AS SHOWN
HEIGHT GAGE
(USE A DIME)
SHAVER HEAD
SHAVER BLADE
BLADE MOUNTING SCREW
6 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
9 37
48
#1002 ASSEMBLY
24
23
41
20
6
4
52
10
3
44
53
49
2
51
5
50
1
36
7 All Models #1002, #1002EX, #1003, AND #1003EX
47
52
10
6
Sno-Konette
9
37
48
#1003 ASSEMBLY
31
41
20
4
44
52
49
3
2
51
5
50
7
8 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
SHAVER HEAD
39
13
46
45
9 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
PARTS LIST
31
32
33
34
35
36
37
38
27
28
29
30
22
23
24
25
26
Model # Model # Model # Model #
1002 1002EX 1003 1003EX
Item No. Part No.
Part No.
Part No.
Part No. Description
1 34036 34036 34036 34036 Door Assembly
2 12012 12012 12012 12012 Front Glass Strip
6
7
8
3
4
5
9
10
12013
12038
12039
12045
12061
12071
22068
22009
12013
12038
12039
12045
12061
12071
22068
22009
12013
12038
12039
12045
12061
12071
22068
22009
12013
12038
12039
22068
22009
Rear Glass Strip
Front Glass (15" x 18")
Side Glass (15" x 11 15/16")
12045 Door Catch (3 Req)
12061 Drain Pan Assembly with Drain (Counter)
12071 Label, "Do Not Apply Pressure" *
Pusher Handle with Gasket & Label
Hopper Casting
19
20
21
14
15
16
11
12
22012
38971
39022EX
38971
22012
42798
39022EX Drive Motor
42798 Motor Switch
13 22015NM 22015NM 22015NM 22015NM Sno-Konette Shave Head
17
18
22021
22034
22038
47201
22021
22034
42369
74087
22021
22023
22034
22038
42798
22021
22023
22034
Pusher Handle Gasket
Rubber Isolator (8 Req)
Ice Shaver Drain Hose (3' Long)
42369
Lead-In Cord *
1088
1206
39068
1088
1206
39068
1088
1206
39068
42798 Light Switch
1088 6 oz Sno Dipper
1206 6 oz. Cup Dispenser with Bracket
39068
Ice Scoop *
41013
22226
22222
41020
41021
41022
41023
41057
47010
47132
47155
49132
74119
41013
22226
22222
41020
41021
41722
41023
41057
47010
47132
47155
49132
74119
41013
N/A
N/A
49837
61115
87065
61112
47010
47132
47155
49132
74119
41013
N/A
N/A
49837
Door Knob *
Dome
Dome Glass
Light Tube Holder *
Light Tube Holder Starter *
Light Ballast *
Light Starter *
Light Tube *
Lamp Holder *
61115 Motor Cover Assembly
87065
40 Watt Light Bulb *
61112 Light Cover (Plastic) *
47010
Label, "Safe Operating Instructions" *
47132 Glass Channel (15" Req)
47155 Rubber Feet (4 Req)
49132
Grip Nut (5/16-8; Motor Mounting; 4) *
74119
Label, "Warning Disconnect Power" *
* Not Shown
10 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
PARTS LIST
47
48
49
44
45
46
50
51
52
53
Model # Model # Model # Model #
1002 1002EX 1003 1003EX
Item No. Part No.
Part No.
Part No.
Part No. Description
39
40
41
42
43
74125
75220
87810
76097
76135
74125
75220
87810
76097
74125
75220
87810
76097
76135
74125 Set Screw (1/4-20 x 3/8)
75220 Hose Clamp with Screw
87810 Strain Relief - Power Cord
76097
Label, "Unplug to Clean" *
Power Cord Tag *
77747
12018
22018
77747
12018
22018
22062
47509
12180
12007
12003
12004
22062
47509
12180
12007
12003
12004
77747
12018
22018
12480
22062
47509
12180
12007
12003
12004
77747 Slot Head Hex Screw (#8-32 x 3/4")
12018 Blade Mounting Screw (8-32 x 3/8" Brass)
22018 Two-Hole Blade Set with Screws
12480 Decal
22062 5/16 x 2 Pan Head M/S
47509 Wall Mount Bracket
12180 Corner Post with Holes (1)
12007 Corner Post (3)
12003 Top Frame
12004 Bottom Frame
* Not Shown
11 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
ELECTRICAL SCHEMATIC – MODEL #1002
12 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
ELECTRICAL SCHEMATIC – MODEL #1003
13 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
ELECTRICAL SCHEMATIC – MODEL #1002EX
14 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
ELECTRICAL SCHEMATIC – MODEL #1003EX
15 All Models #1002, #1002EX, #1003, AND #1003EX
Sno-Konette
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT
PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING
THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA
16 All Models #1002, #1002EX, #1003, AND #1003EX
