High-Resolution B/W CCD Camera CS3960DCL Specifications

High-Resolution B/W CCD Camera CS3960DCL Specifications
Rev 1.0
High-Resolution B/W CCD Camera
CS3960DCL
Specifications
Contents
1. Overview .........................................................................................1
2. Features............................................................................................1
3. Configuration...................................................................................2
4. Optional parts...................................................................................2
5. Specifications...................................................................................2
6. Serial control....................................................................................9
7. Explanation of operation .............................................................10
8. Outline Drawing ............................................................................14
9.Cases for indemnity (limited warranty) .........................................15
10. Restriction for use.......................................................................15
Printed on recycled paper
D4134578A
Rev 1.0
1. Overview
This CCD B/W camera is a high-resolution camera that features all pixel readout mode 2/3 CCD.
2. Features
(1) High resolution
High pixel density CCD (number of effective pixels 1.45 M, number of total pixels 1.50 M) is used.
(2) Square grids
The CCD pixels arrayed in square grids facilitates computation for image processing.
(3) Full-frame shutter
Since all pixels are output even by shutter operation, high resolution can be achieved, without
deteriorating the vertical resolution.
(4) Camera link interface
The interface for image output and camera control complies with the camera link standard.
By using a camera link frame grabber board for camera link, the shot image can be transferred to PC
at high speed, and various camera controls can be performed from PC.
(5) All-pixel readout mode (normal mode)
All pixel signals (in the effective area) are output in approximately 1/30 second.
(6) Partial scan mode
Partial scanning of 400 lines in the center of the screen is possible.
(7) High-speed draft readout mode
By reading 2 lines from every 8 lines, all signals in the effective area are output in approximately in
1/100 second.
(8) Random trigger shutter
By external trigger signal input, the shot image can be grabbed at an arbitrary timing.
(9) Multiple-shutter
By external trigger signal input, the shot image can be grabbed at an arbitrary timing and the
accumulated shot images can be output at an arbitrary timing.
D4134578A
1
Rev 1.0
3. Configuration
(1) Camera body ············································································ 1
(2) Accessories
Instruction Manual (Japanese)···················································· 1
Instruction Manual (English)······················································ 1
4. Optional parts
(1) Power cable
Model name: CPRC3700-**
(2) Camera Link cable
Model name: 14B26-SZLB-***-0LC
(3) Camera mounting kit
Model name: CPT4000CL
(4) Camera adapter
Model name: CA170
*NOTE: Application software is not supplied as a standard item.
Notes on optional parts and compliance with safety standard conditions:
We assure the compliance of this camera with the safety standard when it is used in combination with
the optional parts listed above.
If you use the camera in combination with parts other than specified by our company, you are
responsible for finally confirming the compliance with the safety standard by using the entire
machine/equipment.
5. Specifications
[Electrical specification]
(1) Imager
Interline CCD
·Number of total pixels
1434 (H) x 1050 (V)
·Number of effective pixels
1392 (H) x 1040 (V)
·Pixel size
6.45 µm (H) x 6.45 µm (V)
·Optical size
2/3 type
(2) Scan method
Progressive
(3) Aspect ratio
4:3
(4) Synchronization method
Internal synchronization
(5) Standard subject illuminance
400 lx, F5.6, 3000 K
(6) Minimum subject illuminance
4 lx
( F1.4, GAIN MAX, all pixel readout, video level 50 %)
D4134578A
2
Rev 1.0
(7) Video output
·Data
Compliant with the camera link standard.
12 / 10 / 8 bit switching
·Readout mode
All pixel readout
Approximately 30 fps / 1392(H) x 1040(V)
Partial scan
Approximately 60 fps / 1392(H) x 400(V)
High-speed draft readout
Approximately 100 fps / 1392(H) x 260(V)
(8) Gain
0 to Approximately +12 dB (256 levels)
(9) Setup
Approximately -248 to +511 LSB (1 LSB steps)
(10) Gamma correction
OFF(γ= 1.0) fixed
(11) Power supply voltage
DC12 V ± 10% (ripple 50 mV(p-p) or less)
(12) Power consumption
Approximately 3.6 W
[ Electronic shutter specification]
(1) Shutter speed
·Readout mode
All pixel readout
1/30 to 1/10,000 s
Partial scan
1/60 to 1/10,000 s
High-speed draft readout
1/100 to 1/10,000 s
(2) Random trigger shutter
ON/OFF switching (initial factory setting: OFF)
·Fixed mode
The exposure time depends on the shutter speed setting.
·Pulse width mode
The exposure time depends on the pulse width.
(3) Multiple-shutter
ON/OFF switching (initial factory setting: OFF)
Exposure by TRIG input, readout by MULTI input
* Enabled when random trigger shutter is ON.
[Internal sync signal specification]
(1) Driving frequency
57.28 MHz
(2) Scanning frequency
·Readout mode
All pixel readout
Partial scan
High-speed draft readout
Horizontal
32.00 kHz
Vertical
30.02 Hz
Horizontal
32.00 kHz
Vertical
59.59 Hz
Horizontal
26.92 kHz
Vertical
100.81 Hz
D4134578A
3
Rev 1.0
[ Input signal specification]
(1) TRIG
Camera link I/F and DC IN connector input
·Signal level (DC IN input)
TTL level
·Polarity
Positive/Negative polarity switching possible
·Pulse width
31.25 µs or more
(2) MULTI
Camera link I/F input
·Polarity
Negative polarity
·Pulse width
31.25 µs to 10 ms
[Output signal specification]
]
(1) WEN
DC IN connector output
·Signal level
4 V (p-p)
·Polarity
Positive polarity
·Pulse width
Approximately 31.25 µs
[Dimensions]
]
(1) Lens mount
C-mount
*Depending on the lens you use, the performance of the camera may
not be brought out fully due to the deterioration in resolution and
brightness in the peripheral area, occurrence of a ghost, aberration
and others.
When you check the combination between the lens and camera, be
sure to use the lens you actually use.
(2) Flange back
17.526 mm
(3) Dimensions
55 mm (W) x 60 mm (H) x 63 mm (D)
(4) Mass
Approximately 190 g
(5) Camera body grounding: insulation status
Conductive between circuit GND and camera body
[ Operating ambient conditions]
(1)
(2)
Performance assurance
Operating assurance
Temperature
0 to 40 °C
Humidity
10 to 90 % (no condensation)
Temperature
-5 to 45 °C
Humidity
90 % or less (no condensation)
D4134578A
4
Rev 1.0
[ Typical spectral response]
The lens characteristics and light source characteristics is not reflected in table.
[ Applicable safety standards]
(1) EMC( Electro-Magnetic Compatibility)
EMI( Electro-Magnetic Interference)
EN61000-6-4 / 2001
EMS( Electro-Magnetic Susceptibility)
EN61000-6-2 / 2001
(2) FCC
FCC Part 15 Subpart B class A
[ Communication specification]
(1) Communication speed
9600 bps
(2) Data bit
None
(3) Parity
8
(4) Stop bit
1
(5) Parity bit
None
(6) Handshake
None
D4134578A
5
Rev 1.0
[Connector pin assignment]
]
(1) Video output/controlling connector (Camera Link Base Configuration) CAMERA LINK
Connector model: MDR 26-PIN connector 10226-2210VE (manufactured by 3M).
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
信信信
GND
Tx OUT0Tx OUT1Tx OUT2Tx CLK OUTTx OUT3Ser TC( RxD) +
Ser TFG( TxD) CC1( TRIG) CC2( MULTI) +
CC3CC4+
GND
I/O
O
O
O
O
O
I
O
I
I
I
I
-
Pin No.
14
15
16
17
18
19
20
21
22
23
24
25
26
信信信
GND
Tx OUT0+
Tx OUT1+
Tx OUT2+
Tx CLK OUT+
Tx OUT3+
Ser TC( RxD) Ser TFG( TxD) +
CC1( TRIG) +
CC2( MULTI) CC3+
CC4GND
I/O
O
O
O
O
O
I
O
I
I
I
I
-
(2) Connector for power supply and sync signal input/output DC IN
・ Connector (Camera side): HR10A-10R-12PB (Manufactured by HIROSE DENKI)
・ Plug (Cable side): HR10A-10P-12S (Manufactured by HIROSE DENKI) or equivalents
Pin No.
I/O
Signal Name
1
2
3
4
5
6
7
8
9
10
11
12
I
-
GND
+12V
GND
N.C.
GND
N.C.
N.C.
GND
N.C.
WEN
TRIG
GND
O
I
-
9
1
2
8
10
3
11
7
12
4
6
5
Figure seen from the
back of main body
D4134578A
6
Rev 1.0
[ Timing chart]
(1) Horizontal timing
1) All pixel readout, Partial scan
LVAL
DVAL
DATA OUT
a
b
c
e
d
f
a = 276CLK
b = 112CLK
c = 388CLK
d = 1392CLK
e = 10CLK
f = 1790CLK
2) High-speed draft readout
LVAL
DVAL
DATA OUT
a
b
c
e
d
f
a = 276CLK
b = 112CLK
c = 388CLK
d = 1392CLK
e = 348CLK
f = 2128CLK
D4134578A
7
Rev 1.0
(2) Vertical timing
1) All pixel readout
FVAL
LVAL
DVAL
DATA OUT
A
B
C
D
E
F
A = 3H
B = 10H
C = 13H
D = 1040H
E = 13H
F = 1066H
2) Partial scan
FVAL
LVAL
DVAL
DATA OUT
A
B
C
D
E
F
A = 3H
B = 67H
C = 70H
D = 400H
E = 67H
F = 537H
3) High-speed draft readout
FVAL
LVAL
DVAL
DATA OUT
A
B
C
D
E
F
A = 3H
B = 2H
C = 5H
D = 260H
E = 2H
F = 267H
D4134578A
8
Rev 1.0
6. Serial control
You can control following function by camera link I/F.
(1) Memory control
・ Save
・ Load
・ Reset
(2) Setup setting
-248~ +511 LSB (1LSB step)
(3) Gain setting
0 ~ +12 dB (256 levels)
(4) Shutter speed setting
1/30, 1/60, 1/100 ~ 1/10,000 s
(5) Random trigger shutter setting
ON / OFF
・ trigger polarity
Positive polarity / Negative polarity
・ Random trigger mode
Pulse width mode / Fixed mode
(6) Multiple-shutter
ON / OFF
*Enabled when random trigger shutter is ON
(7) High-speed draft readout
ON / OFF
(8) Partial scan
ON/ OFF
Note: High-speed draft readout mode and partial scan mode cannot be used at the same time.
D4134578A
9
Rev 1.0
7.
.Explanation of operation
7.1 Readout mode
Video is output from the camera link connector. The output video can be grabbed by the frame grabber board.
The frame rate and resolution of output images that this model supports are as follows:
1) All pixel readout
: Approximately 30 [fps] / 1392(H) x 1040(V)
2) Partial scan
: Approximately 60 [fps] / 1392(H) x 400(V)
3) High-speed draft readout : Approximately 100 [fps] / 1392(H) x 260(V)
1) All pixel readout
Reads out all pixels in about 1/30 second.
1066H
FVAL
LVAL
1
2
3
4
5
6
7
8
1038
1039
1040
DVAL
DATA OUT
D4134578A
10
Rev 1.0
2) Partial scan
Skips the top and bottom of the effective area and reads out 400 lines in the center area in
approximately 1/60 second.
537H
FVAL
LVAL
719
720
721
322
323
324
325
326
327
328
DVAL
DATA OUT
Skipped lines: 321 line
Effective lines : 400 line
Skipped lines : 319 line
High-speed transfer: 64 line
+
Nomal-speed transfer: 2 line
Effective lines: 400 line
Skipped lines : 64 line
3) High-speed draft readout
By reading 2 lines out of every 8 lines, reads out the whole valid area in approximately 1/100 seconds.
Control and setting of functions can be done by accessing the cam
267H
FVAL
LVAL
1
4
9
12
17
20
25
1028
1033
1036
DVAL
DATA OUT
Reading 2 lines out of every 8 lines in
the inside of a total of 1040 lines
Effective lines : 260 lines
D4134578A
11
Rev 1.0
7.2 Random trigger shutter
In the random trigger shutter mode, you can shoot and grab an image at an arbitrary timing by trigger
signal input from the external.
·External trigger signals can be input either from the camera link I/F CC1 or DC IN connector.
·If polarity is set to negative polarity, exposure starts at the falling edge of the trigger.
·The random trigger shutter of this camera can be operated in two types of mode: fixed mode and
pulse width mode. How to determine the exposure time differs depending on the mode.
1) Fixed mode
·The exposure time is determined by the setting value for the shutter speed.
·FVAL is output in sync with the first or next LVAL after the end of exposure time.
exposure time
TRIG
approx.
2.4us
CCD
FVAL
LVAL
DVAL
DATA OUT
2) Pulse width mode
·The exposure time is determined by the pulse width (exposure time = pulse width + approximately 5µs).
·Set a pulse width of 1H (approximately 31.25µs) or more.
·FVAL is output in sync with the first or next LVAL after the end of exposure time.
exposure time
TRIG
approx.
2.4us
approx. 7us
CCD
FVAL
LVAL
DVAL
DATA OUT
D4134578A
12
Rev 1.0
7.2 Multiple-shutter mode
In the multiple-shutter mode, video is output in sync with a MULTI signal from the external after the end
of exposure time.
·Valid only when the random trigger shutter mode is ON.
·MULTI signals can be input from the camera link I/F CC2.
·If exposure is executed several times before MULTI signal input, the images are output superposed.
·The exposure time is determined by the random trigger shutter mode setting and its determination
method.
·The pulse width must be set to negative polarity and 1H (approximately 31.25 µs) to 10 ms.
·FVAL is output in sync with the first or next LVAL after the end of MULTI signal input.
TRIG
MULTI
A
B
CCD
FVAL
LVAL
DVAL
DATA OUT
A+B
D4134578A
13
Rev 1.0
8. Outline Drawing
D4134578A
14
Rev 1.0
9.
.Cases for indemnity (limited warranty)
We shall be exempted from taking responsibility and held harmless for damage or losses incurred by the
user in the following cases
In the case damage or losses are caused by fire, earthquake, or other acts of God, acts by a third party,
deliberate or accidental misuse by the user, or use under extreme operating conditions.
In the case of indirect, additional, consequential damages (loss of business interests, suspension of
business activities) are incurred as result of malfunction or non-function of the equipment, we shall be
exempted from responsibility for such damages.
In the case damage or losses are caused by failure to observe the information contained in the
instructions in this instruction manual and specifications.
In the case damage or losses are caused by use contrary to the instructions in this instruction manual and
specifications.
In the case damage or losses are caused by malfunction or other problems resulting from use of
equipment or software that is not specified.
In the case damage or losses are caused by repair or modification conducted by the customer or any
unauthorized third party (such as an unauthorized service representative).
Expenses we bear on this product shall be limited to the individual price of the product.
10.
.Restriction for use
Should the equipment be used in the following conditions or environments, give consideration to safety
measures and inform us of such usage:
1.
Use of the equipment in the conditions or environment contrary to those specified, or use outdoors.
2.
Use of the equipment in applications expected to cause potential hazard to people or property,
which require special safety measures to be adopted.
This product can be used under diverse operating conditions. Determination of applicability of
equipment or devices concerned shall be determined after analysis or testing as necessary by the
designer of such equipment or devices, or personnel related to the specifications. Such designer or
personnel shall assure the performance and safety of the equipment or devices.
This product is not designed or manufactured to be used for control of equipment directly concerned
with human life (*1) or equipment relating to maintenance of public services/functions involving
factors of safety (*2). Therefore, the product shall not be used for such applications.
(*1): Equipment directly concerned with human life refers to.
· Medical equipment such as life-support systems, equipment for operating theaters.
· Exhaust control equipment for exhaust gases such as toxic fumes or smoke.
· Equipment mandatory to be installed by various laws and regulations such as the Fire Act or
Building Standard Law
· Equipment related to the above
(*2): Equipment relating to maintenance of public services/functions involving factors of safety refers to.
· Traffic control systems for air transportation, railways, roads, or marine transportation
· Equipment for nuclear power generation
· Equipment related to the above
D4134578A
15
Rev 1.0
Head Office
: 7-1, 4 chome, Asahigaoka, Hino-shi, Tokyo, 191-0065, Japan
(Overseas Sales Department)
Phone : +81-42-589-8771
Fax
: +81-42-589-8774
URL
: http://www.toshiba-teli.co.jp/
Distributor
• This product must be classified for disposal according to the laws of each country and municipal laws.
• Information contained in this document is subject to change without prior notice.
D4134578A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement