70-171 Autocreaser Pro 50 (CB) Operators Manual Issue 4

70-171 Autocreaser Pro 50 (CB) Operators Manual Issue 4

AutoCreaser Pro 50

(CB/UL)

DOCUMENT

CREASING MACHINE

OPERATORS MANUAL

Morgana Systems Limited United Kingdom

Telephone: ( 01908 ) 608888 Facsimile: ( 01908 ) 692399

Website: www.morgana.co.uk

ISSUE 4

JANUARY 2013

70-171

INDEX

INTRODUCTION

The Morgana AutoCreaser Pro 50

SAFETY Do’s & Don’ts

THE AUTOCREASER Pro 50

Labeled Photograph

THE CONTROLS

The switch panel

Features on the switch panel

QUICK START GUIDE

OPERATING THE AUTOCREASER Pro 50

Setting the machine

Programming the machine

Reading stored programmes

Paper jamming

THE STACKER ASSEMBLY

Setting the Stacker unit

PERFORATING

Equipment, spares

Setting the machine

THE BLADE ASSEMBLY

Setting the blade pressure

Setting the blade alignment

REPLACING CREASING BLADE SETS

Installing new blade sets

Spares

TROUBLE SHOOTING

DISPATCH KIT

ACCESSORIES & OPTIONS

RECOMMENDED SPARES

FUSE POSITIONS AND RATINGS

PRODUCT RECYCLING AND DISPOSAL

Page 2

PAGE 3

4

6

30

32

33

35

36

37

39

40

48

49

50

52

53

9

20

26

27

29

CREASING

AutoCreaser Pro 50

INTRODUCTION

AutoCreaser Pro 50

The Morgana AutoCreaser Pro 50 is a fully automatic suction feeding creasing system designed for use with both conventional litho and digital printers.

The feed on the AutoCreaser Pro 50 can also be manually operated for use with heavy stock, very small or very large sheets, embossed or even irregular sheets.

The crease is programmed from the leading edge of the sheet using the controls on the front panel.

The blade and anvil are mechanically controlled over their entire length and can be adjusted to accommodate various weights of media.

IMPORTANT

The operating environment should be controlled to a temperature between

16° C and 27° C Maximum

Specification

Feeding System ................................................ Bottom suction feed

Max. Sheet Size ................................................ 700mm x 500mm (27.5” x 19.7”) [900mm x

500mm (35.4” x 19.7”) with Optional extension table].

Min. Sheet Size (in automatic mode)................. 210mm x 140mm (8.5” x 5.5”)

Max. Paper Thickness........................................ 0.4mm (varies according to hardness, type of fold, and substrate)

Max. No. Creases per Sheet ............................ 16

Min. Distance Between Creases ....................... 0.1mm

Max. No. Stored Programmes .......................... Unlimited

Min. Crease Distance from Leading Edge ........ 2.5mm

Min. Crease Distance from Tail Edge ................35mm

In Hand Feed Mode up to 2499.9mm to Last Crease can be Programmed.

Speed per Hour (A4 in half) ..............................8500

Speed per Hour (A5 in half) ..............................11000

Dimensions ....................................................... L: 1500mm H: 1224mm W: 682mm

L: (59”) H: (48.2”) W: (26.8”)

Weight ............................................................... 156Kgs (+50Kgs packing)

Power Requirement .......................................... 1 phase 230v 50Hz

1phase 220v 60Hz

Sound Power Level ................................78.5 decibels

*As part of our continued product improvement plan, specifications and information published in this manual are subject to change without notice.

All specifications are dependant on application, type of stock, temperature, RH and print engine used.

Specifications quoted were measured on uncoated and unprinted stock. E & OE.

SYSTEM

Page 3

Safety Do’s & Don’ts

Safety Do’s & Don’ts

REGLES DE SECURITE : « A FAIRE » ET « A NE PAS FAIRE »

Do - read this operator manual fully before operating the machine.

Lire ce mode d'emploi avant d'utiliser la machine.

Do - operate with the designated AC current only. Use an exclusive outlet, as overloading may cause fire or an electric shock.

Respecter l'alimentation électrique indiquée. Brancher sur une prise séparée car une surcharge peut entraîner un incendie ou un choc électrique.

Do - install the power cord out of the way to avoid a tripping hazard.

Installer le cordon d'alimentation de manière à ne pas pouvoir trébucher par dessus.

Do - make sure that the mains inlet connector is always easily accessible.

Ménager un accès libre à la prise de courant.

Do not - install the machine in an unstable place such that it tilts or shakes.

Ne pas installer la machine sur une surface non plane, afin d'éviter qu'elle ne penche ou ne vibre.

Do not - unplug the plug or unplug the power cord from the outlet with a wet hand, this can cause an electric shock.

Ne pas installer la machine sur une surface non plane, afin d'éviter qu'elle ne penche ou ne vibre.

Do not - unscrew and remove any covers from the machine, as it can cause an electric shock or injury.

Ne démonter et enlever aucun carter de la machine, par crainte de décharge

électrique ou de blessure.

Do not - place receptacles containing liquids on any surface.

Ne pas placer de récipient contenant un liquide sur la machine.

Do not - adjust any part of the machine whilst rollers are running

N'effectuer aucun réglage pendant que les rouleaux fonctionnent.

Do not - operate the machine with loose or trailing clothing or loose hair.

Ne pas porter de vêtements flottants et rassembler les cheveux longs lors de l'utilisation de la machine.

Do not - under any circumstances adjust the paper gate when the machine is switched on.

En aucune circonstance, régler le séparateur de papier lorsque la machine est branchée.

Page 4

CREASING

AutoCreaser Pro 50

Warning Labels

Do - be aware of any finger traps and rotating parts when operating the machine.

Attention au risque de se coincer les doigts, et aux pièces en mouvement lors du fonctionnement de la machine.

Do - read this operator manual fully before operating the machine.

Lire ce mode d’emploi avant d’utiliser la machine.

Do not - operate the machine with loose or trailing clothing.

Ne pas porter de vêtements flottants lors de l'utilisation de la machine

Do not - operate the machine with loose hair.

Rassembler les cheveux longs lors de l'utilisation de la machine.

SYSTEM

Do - be aware of any finger traps and rotating parts when operating the machine.

Attention au risque de se coincer les doigts, et aux pièces en mouvement lors du fonctionnement de la machine.

Do - be aware of sharp points and blades.

Attention aux éléments tranchants et aux couteaux.

Do - be aware of rotating rollers.

Attention aux rouleaux en fonctionnement

Do - be aware of low current anti-static shock.

Attention aux faibles chocs d'électricité statique

Page 5

AUTOCREASER Pro 50

AutoCreaser Pro 50

DOCUMENT CREASING MACHINE

Key to photograph below

1 Roller tilt handle

2 Stacker assembly

3 Suction slot knob

4 Touchscreen

7 Adjustable side lay

8 Back Stop

9 Fixed side lay

10 Roller tilt knob

5 Air separation knob 11 Paper Gate

6 Air distribution knob 12 Exit Guard

13 Switch Panel

14 Fuses

15 Gap Set Knob and Lever

16 Vacuum Bleed Knob

Page 6

CREASING

AutoCreaser Pro 50

THE CONTROLS

THE SWITCH PANEL

The Switch Panel houses the Compressor switch, System switch, and an industry standard Emergency Stop switch which will stop all power going to the machine when activated.

Compressor Switch

System Switch

Emergency Stop Switch

Features on the Switch Panel

System switch

When activated the system switch will operate the motors in order to begin the creasing sequence.

Compressor switch

Allows the operator to switch off the compressor unit in order to utilise the machine to manually feed sheets.

SYSTEM

Page 7

THE CONTROLS

BLANK

PAGE

Page 8

CREASING

AutoCreaser Pro 50

Quick Start Guide

1.

2.

3.

4.

5.

Setting the machine to operate in automatic sheet feed mode

Set the gap between the paper gate and the vacuum roller to approximately twice the thickness of the stock to be creased.

Place the stock to be creased onto the loading table against the fixed side lay.

Release the clamps on the adjustable side lay and slide up to the paper stack allowing a gap of approximately 0.5mm (1/64 inch) between the paper and the side lay.

Position the backstop and slide it up to the paper stack, also allowing a gap (as stated in the above step).

Turn the Emergency Stop button clockwise to switch the power on. After the system start up procedure the touch screen will be displayed as shown below.

IMPORTANT.

If you have not been trained to operate this machine, we strongly advise that you select the red cross icon.

We recommend that you either seek training or ask a trained operator to run the machine for you.

Select the green tick icon only if you have been trained to operate this machine.

If you have not been trained to operate this machine and you select the green tick icon,

Morgana Systems Ltd accept no responsibility for personal injury, damage to the machine or damage to materials being processed by the machine.

WARNING:-

Wait at least 10 seconds, after making any selection on the Touchscreen panel, before switching the machine OFF. Failure to do so could result in the data storage being corrupted, and the machine not operating.

SYSTEM

Page 9

Setting page

Quick Start Guide

The touch screen is laid out into 3 main areas as shown below:

Status of machine & data entry area. Also used for quick links to setting pages.

Settings Pages.

Vacuum Suck - There are two selections available - 1 short suck & 2 continuous for stream feeding.

Highlighted number is type currently selected. The status area also shows currently selected suck.

Batch Button - Image is identical to that shown in the status area. On selection the status area is replaced with a calculator for inputting new values.

Batches of any numerical value.

Tabs to enable switching between setting pages - choose either Paper Settings,

Crease Setting, Store or Tools

Paper Settings Page.

Fold Selection - For quick setting of crease positions on standard size sheets.

Highlighted fold is type currently selected, other folds may be selected.

Currently selected fold is shown in the status area.

Toggle between, Delay between batches and stop after batch

Page Length - On selection the status area is replaced with a calculator for inputting new values.

Min Length = 190mm

Current Job Name

Arrows may be selected to increase or decrease the page size in 0.1mm

increments

Page 10

CREASING

AutoCreaser Pro 50

Quick Start Guide

Crease settings Pages.

To get to the crease setting page click the lower tab the status area.

or from

If you have selected a predefined standard crease type from the paper settings page the crease positions will be set for you. These positions can be fine tuned by ± 0.1 mm increments by pressing side arrow buttons for each crease.

Number of creases – if more than 6 creases are added a scroll bar will appear to enable viewing of all creases

Arrows may be selected to increase or decrease the crease position in 0.1mm increments

Plus box for inserting additional creases. On selection following creases will move down by one place a maximum number of 6 creases can be seen at any one time further creases can be accessed by use of the scroll bar.

Crease position - On selection the status area is replaced with a calculator for inputting new values.

Cross box for deletion of crease.

On deletion of crease following creases will move up by one place. You will be asked to confirm deletion of the crease.

Press to remove all creases – you will be asked to confirm deletion.

Scroll bar - use to bring required crease into view.

Crease on/off selector green is on & red is off.

This is also indicated in the status area.

Additional creases added – scroll bar appears for more than six creases.

SYSTEM

Page 11

Quick Start Guide

Page 12

Creasing turned off -

Greyed out areas are unselectable. Status area willshow creasing is off with red icon

CREASING

AutoCreaser Pro 50

Run Job

Quick Start Guide

Click to start machine with settings currently shown you will receive a notification if system switch is not on. Press again to stop Job

System Switch Not On

Push System Switch down to start the machine.

The machine running screen will appear.

SYSTEM

Click to stop machine

Page 13

Quick Start Guide

Cover Crease Mode.

1. Select the Paper Settings Tab.

2. Enter the Paper Length and then select the Cover Crease button.

Cover Crease button

Paper Length

3. Select the Crease Settings Tab.

Spine Offset Spine Width

Arrow Button

Hinge Distance

4. Enter the Spine Width dimension. If necessary, adjust the Spine Offset from the centre of the sheet.

5. Select the arrow button to set the hinge Dimension.

Page 14

CREASING

AutoCreaser Pro 50

6. Enter the Hinge Dimension.

Quick Start Guide

Hinge Dimension

7. Select the arrow button to highlight the Spine Offset and the Spine Width dimensions.

8. Run the sheets of paper through the machine to make the Spine creases.

TO MAKE THE HINGE CREASES.

9. Remove the sheets of paper from the stacker tray.

and put them back onto the loading table.

TURN THE SHEETS OVER

,

MAKE SURE THAT THE LEAD EDGE

OF THE SHEETS POINT IN THE SAME DIRECTION AS BEFORE.

10. Select the arrow button to highlight the Hinge Dimension.

11. Run the sheets of paper through the machine to make the Hinge creases.

SYSTEM

Page 15

Quick Start Guide

Status Screen

Paper length - input from the paper setting screen

Clicking in this area will take you to the paper setting page

Currently selected Vacuum

Suck setting - for stream setting choose selection 2

Lead Edge Sensor Strength,

Indicator Bar

Number of creases - this may alter automatically if a pre - defined fold is selected. Adjustments may be made in the crease setting screen

Green icon indicates settings are saved - a red icon would show that settings have been changed but the job has not been saved.

Batch quantity - this is input from the batch calculator on the paper setting screen - max. 999

Sheet count -click to zero

A screen will appear to confirm that you want to reset the count.

Batch count - click to zero

A screen will appear to confirm that you want to reset the count.

Currently selected fold type

- can be one of the following.

Clicking in this area will take you to the Crease setting page

Current machine speed setting

Click to start machine with settings currently shown - you will receive a notification if system switch is not on. Press again to stop

Job

Clicking in this area will take you to the Tools page

Select this button to produce

3 test sheets with the settings currently shown.

Clicking in this area will take you to the Job Store page

Clicking in this area will take you to the paper setting page.

Page 16

CREASING

AutoCreaser Pro 50

Quick Start Guide

The Status Screen will on occasions be replaced with an Input Calculator Screen as shown below.

Pre - set Paper sizes for quick insertion – Standard sizes for country origin would be shown

Pre - set Batch sizes for quick insertion.

Paper size Batch size Crease position input calculator input calculator input calculator

NOTE:

The green tick or the red cross must be selected on the Calculator Screen to make the left hand side of the touchscreen active again.

SYSTEM

Page 17

Tools Screen

Quick Start Guide

Machine Speed Adjustment:-

Speed setting 3 will give the fastest throughput of stock through the machine.

Use speed setting 1 or 2 for troublesome stocks, or to synchronise the speed of the AutoCreaser to a

Morgana Autofold Pro, when they are used together.

Inch paper in direction of arrow to clear jams

Clean Lead Edge Sensor

Click on Up Arrow to put Anvil into Top

Dead Centre position

(TDC)

Inch paper in direction of arrow to clear jams

Touch Screen Calibration

See Page 19

Change Machine measurement settings, Imperial / Metric

Clicking this icon will show Machine program revision &

Touch Screen software revision.

Touch screen software version

Main Processor Program version

Page 18

CREASING

AutoCreaser Pro 50

Quick Start Guide

Touch Screen Calibration.

1.

Switch the mains power on and wait for the main screen to appear before commencing to check the horizontal and vertical position of the display.

The position of the display within the surround is achieved by operating the button at the rear of the housing, press this a number of times to obtain the correct orientation required, move to the next button to move the position to centralize horizontal.

2.

(i) Select the tools menu tab, and then Select the Touch Screen calibration icon.

(ii) Using a plastic pointer, soft leaded pencil, biro cap etc. and with gentle pressure.

Touch the centre of the cross in each corner of the Touch Screen, as prompted, by the hand graphics. This procedure will calibrate the Touch Screen.

SYSTEM

Page 19

Operating the Autocreaser Pro 50

Setting the Machine

Adjusting the Paper Gate

Set the height of the Paper Gate to approximately two thicknesses of paper, by turning the disc j. An excessive gap is a most likely cause of double sheet feeding.

This setting is only intended as a guide, for instance, sheets with an upward curl will require this setting to be increased.

J

TWO THICKNESSES

OF PAPER

WARNING.

DO NOT ADJUST THE

PAPER GATE WHILE THE

MACHINE IS RUNNING OR

THE SUCTION DRUM MAY

BECOME DAMAGED.

Setting the Suction Slot

The suction slot is located inside the vacuum roller and can be adjusted by releasing and moving the suction knob horizontally in either direction to the required position.

For light stocks set the knob to the left and for heavier stocks set the knob to the right.

FIG 8.1

Adjustable

Side Lay

Suction

Slot Knob

Page 20

CREASING

AutoCreaser Pro 50

Operating the Autocreaser Pro 50

Setting the Adjustable Side Lay

Place the paper stack on to the loading table and slide up to the fixed side lay and paper gate. Release the clamps located at each end of the side lay and slide up towards the paper stack as demonstrated in fig 8.1. Allow a gap of approximately 0.5mm (1/64 inch) between the paper and the side lay.

Setting the Back Stop

Position the backstop and slide up towards the paper stack allowing a gap (as specified in the above step).

Setting the Air Distribution

Depending on the length of the sheet to be creased, the air distribution knob can be rotated to various positions in order to supply air to different ports. Position 2 is recommended for most sheet sizes. However, a better result may be obtained by using the settings below or by experimentation.

Position 1 -

2 -

3 -

4 -

5 -

0 -

For sheets longer than A3 (17”) in order to supply air to the centre of the stack, ports 2, 3 and 4 open.

For A5 sheets or 8 inches long, ports 1 and 2 open.

For A4 sheets or 11 inches long, ports 1 and 3 open.

For A3 sheets or 17 inches long, ports 1 and 4 open.

For sheets longer than A3 (17”) in order to supply air to the ends of the stack, ports 1 and 5 open.

For sheets longer than A3 (17”) in order to supply air evenly along the stack, ports 1, 3 and 5 open.

Port 1 Port 5

Air Distribution

Knob Shown

Set To Posn. 1

Setting the Air Separation Pressure

To control the amount of air supplied to the ports, the air separation knob can be rotated clockwise to decrease the pressure or anti-clockwise to increase the pressure.

SYSTEM

Page 21

Operating the Autocreaser Pro 50

Setting the Roller Tilt Mechanism

The roller tilt mechanism has been designed to compensate for when the creasing position on the sheet is not square. This could be due to an inaccuracy in the media or if the roller tilt mechanism has been incorrectly set. The mechanism will be set to zero

(square) when the machine is supplied.

To set the mechanism, unlock the roller tilt knob located below the roller tilting handle by turning anti-clockwise. Move the roller tilt handle left or right in order to compensate for any inaccuracy. When the position is set, ensure to lock the roller tilt knob before operating the machine. Repeat the above procedure until the creasing position is square.

Setting the positions of drive wheels and hubs

It is important that the drive wheels and drive hubs on the roller shafts are arranged evenly across the width of the media being creased. This is done to ensure that the media is accurately driven and supported through the rollers.

The drive wheels and hubs are fixed to the rollers by means of a grub screw. To locate this grub screw the rollers can be rotated by operating the motor manually.

DO NOT ROTATE THE DRIVE ROLLERS BY HAND.

To operate the motors manually, switch the machine ‘on’ at the Emergency Stop switch.

Select the Tools tab that shown below.

at the bottom of the touch screen, the display will change to

Left arrow of arrow to clear jams

Right arrow of arrow to clear jams

Press the system switch down and then select the right or left arrows, to rotate the rollers in short pulses.

Lift the exit guard to see if the grub screws in the drive wheels and hubs can be seen. If the grub screws cannot be seen, lower the exit guard and rotate the rollers by selecting the right or left arrows. Loosen the drive wheels and hubs with a 2mm allen key. Arrange the drive wheels and hubs as shown in FIG 10.1. In order to avoid marking on some types of media ensure a gap between the drive wheels and hubs.

This procedure should be repeated when installing perforating blades and anvils onto the drive wheels and hubs.

Page 22

CREASING

AutoCreaser Pro 50

Operating the Autocreaser Pro 50

FIG 10.1

Set Feed

The length of suction on the sheet of paper being fed can be adjusted by setting the feed type as follows:-

Select 1 for short suck, select 2 for continuous suck (stream feeding).

Vacuum Suck

Select 1 for short suck

Select 2 for continuous suck

(Stream feeding)

NOTES.

1.

Stream Feed

will give the quickest through put of stock through the machine.

2. When the first crease is less than 37mm from the leading edge of the paper the feed will be noticeably slower when using speeds 2 and 3.

3. When the first crease is less than 50mm from the leading edge of the paper the feed will be noticeably slower when using speed 3.

SYSTEM

Page 23

Operating the Autocreaser Pro 50

S

etting the infeed roller gap set

The gap between the infeed rollers must be adjusted to suit the stock being used. The gap set can be adjusted as follows:-

1. Place a sample sheet of the stock to be used onto the feed bed.

2. Select the Tools tab change to that shown below.

at the bottom of the touch screen, the display will

3. Press the system switch down and then select the left arrow on the touch screen, to rotate the rollers in short pulses until the sheet is gripped in the infeed rollers..

4. Test the grip of the sheet in the rollers by trying to remove the sheet by hand, the sheet should be lightly gripped by the rollers. If the grip on the sheet is too light or too heavy it can be adjusted as follows:-

(i) Turn the gap set locking knob anti-clockwise to unlock.

(ii) Move the gap set lever up to increase the gap or down to decrease the gap.

(iii) Turn the gap set locking knob clockwise to lock.

Gap Set

Lever

Gap Set

Locking

Knob

Page 24

CREASING

AutoCreaser Pro 50

Operating the Autocreaser Pro 50

SYSTEM

Page 25

Operating the Autocreaser Pro 50

Programming the machine

1.

Switch the power ‘on’ by turning the Emergency stop button clockwise to release the safety latch.

Setting the page length

2.

Set the page length of the paper as described on page 10.

Setting the vacuum suck

3.

Set the vacuum suck as described on page 10. Setting number 1 for short suck and setting number 2 for continuous suck (stream feed).

Setting the batch quantity

4.

Select the button. On selection the status area is replaced with a calculator for inputting new values.

Setting the crease positions

5. (i) Select the lower tab

Crease Settings Page.

or from the status area to get to the

(ii) Set the creases as described on pages 11 and 12.

Storing the Job

6.

The job that has been set can now be stored as follows.

(i) Select the lower tab

Store Settings Page.

or from the status area to get to the

(ii) The job can be given a name and stored as described below. You can also retrieve previously saved jobs, modify them or delete jobs that are no longer required.

To create a new job name click in text area & keyboard will open to input job name.

Load existing job from store

Clicking to search currently stored jobs

Clicking to delete currently stored jobs

Current Job Name

Yellow Text Denotes Saved Job

Red Text Denotes Unsaved Job

Clicking to save job shown.

Page 26

CREASING

AutoCreaser Pro 50

Operating the Autocreaser Pro 50

Keyboard for entering job name.

Delete all characters Delete last character click save icon job to store to save

Save confirmation screen.

To confirm saving of Job click here.

Search for current jobs to load or modify.

You can search for jobs by clicking the search icon keyboard for text input.

, this will bring up the search

Typein job description or first few characters

To change your mind & return to the previous screen click here.

SYSTEM

Press search icon to start search

Page 27

Operating the Autocreaser Pro 50

Jobs matching characters in text box will be shown in this area - selecting job from this area will show job settings in the right hand status area. Job selected will be shown in text box.

Toggle between search results &full list of jobs

Press to load job shown in text box.

Loading job confirmation screen.

The loaded job can be run or modified and saved as the same job name.

Overwrite job confirmation screen.

To cancel overwrite of

Job press here.

To confirm overwrite of Job press here.

Page 28

CREASING

AutoCreaser Pro 50

Delete job confirmation screen.

Operating the Autocreaser Pro 50

Tocancel deletion of

Job press here.

To confirm deletion of

Job press here.

Running the machine

Run the job as described on page 13. The machine will complete its creasing operation if a sheet has already been fed through the paper gate.

Paper jamming

In the event of a paper jam occurring whilst the machine is operating, select the Tools tab at the bottom of the touch screen, the display will change to that shown below. Press the system switch down and then select the right or left arrows, to inch the paper forwards or backwards.

Inch paper in direction of arrow to clear jams

Inch paper in direction of arrow to clear jams

Setting the machine to operate in manual sheet feed mode

In order to feed heavy stock, very small or very large sheets, embossed or even irregular shaped sheets, it may be necessary to feed the sheets manually. The machine can be programmed and set up in exactly the same way as explained when operating the machine automatically. However, the paper gate must be raised to its highest position for the sheets to be fed freely. Operating the machine in manual sheet feed mode will also require the suction length to be continuous in order to accommodate various types of stock. Therefore, the feed should be set to

Stream Feed

The machine can now be started by activating the System switch to ‘on’.

the Compressor switch.

(Vacuum Drum position 2) see page 10.

Do not activate

Select the icon on the touch screen and begin to slide the sheets individually through the paper gate until they are driven by the drive belts.

To stop feeding the sheets, select the

System Switch off.

icon on the touch screen and switch the

SYSTEM

Page 29

The Stacker Assembly

The stacker unit on the machine is used to catch the sheets once they have been creased or perforated.

Setting the Stacker assembly

1.

Assemble the stacker unit to the machine as shown in fig 13.1 below.

Important

Ensure that the stacker unit has been assembled to the machine properly. However, if it has not, the connection on the magnetic switch will be broken and the machine will not operate (see Trouble shooting pages for details).

There are two side guides on the stacker unit; a left handed (fixed) guide and a right handed (movable) guide held on by a magnetic strip. There is also a left hand extension guide. The guides will control the way in which the paper is collated by setting their positions on the stacker bed.

2.

3.

Place a single sheet (from the stack to be creased / perforated) on to the stacker bed against the fixed ‘left hand’ guide.

Position the ‘right hand’ side guide on to the stacker bed leaving a minimum clearance of approximately 1mm each side of the sheet.

LEFT HAND

BACK STOP

LEFT HAND

SIDE GUIDE

Page 30

RIGHT HAND

SIDE GUIDE

RIGHT HAND

BACK STOP

CREASING

AutoCreaser Pro 50

The Stacker Assembly

4.

5.

Whilst the sheet is between the two guides on the stacker bed, set the distance between the top of the sheet and the backstop flanges to approximately 5mm.

For shorter sheets, the back stop can be used (as shown in FIG 13.1) to adjust the position of the paper stack.

l l

TIPS

One of the back stops supplied with the machine (on the stacker assembly) can also be used as a tool holder as demonstrated in the photograph (left).

The scale on the bed can be used to measure the desired creasing or perforating position on the sheet.

SYSTEM

Page 31

Perforating

Once the machine is set-up, the Autocreaser Pro 50 can be used to perforate or crease.

Note

Perforating and creasing can be carried out simultaneously. However, if any adjustment is made to the roller tilt mechanism in order to compensate for the perforation line being ’out of square’, this may effect the accuracy of the crease. If this occurs creasing and perforating must be carried out as separate operations.

The components and tools required to install the perforator are contained in the despatch kit supplied with the machine, they are listed below.

1 off Set of standard perforation ‘56 tooth’ blades.

1 off Set of standard hardened anvils.

1 off Perforator stripper.

1 off 3mm bondhus wrench / allen key

1 off 2mm bondhus wrench / allen key

The perforator blades are split into two matching halves and are fitted to the drive wheels as shown in the photograph using the four screws supplied.

A hardened anvil is fitted to the drive hub as shown in the photograph also using the four screws supplied. Again the anvils are made from matching halves.

Important: The perforator blades are very sharp and care must be taken whilst handling.

Do not mix the matching pairs of blades or anvils.

Perforating ‘Spares’ kits

For perforating and other types of paper, various spares kits are available which can be assembled to the machine in the same fashion. They are listed below along with a range of scoring wheels,

Perforating blades

56 teeth Part Number

1-99-41

- Standard stock / fine perforations.

Anvils

28 teeth Part Number

1-99-12

- Medium stock / medium perforations.

20 teeth Part Number

1-99-10

- Heavy stock / coarse perforations.

Standard Part Number

1-99-35

- For all blade types

Page 32

CREASING

AutoCreaser Pro 50

Perforating

2.

3.

All of the blades and anvils are supplied with fixings.

*Perforator stripper

Standard Part Number

78-013

*It is recommended that for multiple perforations, a separate perforator stripper is used for every perforating blade set fitted in the creasing unit.

Setting the machine

1.

Turn the mains supply to the machine ‘off’.

4.

5.

Remove the stacker unit and open the exit guard.

Locate and remove the blades / anvils from the despatch kit supplied with the machine.

Using the 2mm allen key (supplied), loosen the drive wheel that is to accommodate the blades.

Slide the drive wheel away from any obstructing drive wheels or hubs in order to mount the blades.

FIG 16.1

6.

Using the 2.5mm allen key (supplied), take one of the matching pairs and mount on to the drive wheel. Do not secure the blade.

7.

Mount the other matching pair to the drive wheel as shown (fig 16.1). Secure the blades to the wheel ensuring not to over tighten grub screw.

8.

Mark on a single sheet the desired perforating position. Feed the sheet through the machine manually until the mark can be seen. Use this mark to assist in fixing the position of the perforating drive wheel to the roller drive shaft.

9.

Using the 2mm allen key, loosen the drive hub nearest the perforating drive. Slide the drive hub away from any obstructing drive wheels or hubs in order to mount the anvils.

10. Using the 2.5mm allen key, take one of the matching pairs of anvils and mount to the drive hub. Do not secure the anvil.

FIG 16.2

SYSTEM

Page 33

Perforating

11.

Mount the other anvil ensuring that they have matched on the drive hub. Secure the anvil to the hub ensuring not to over tighten grub screw as shown in fig 16.2.

12.

Slide the drive hub towards the perforating drive wheel until there is a clearance of 0.5mm.

13. To prevent damage to the blades or the anvils, do not force the drive wheel against the hub.

14. Fix the perforator stripper adjacent to the drive wheel and blade as shown.

15. Operate the machine and test the perforations for form.

It is important that the drive hubs are arranged evenly across the width of the paper in order to reduce the risk of jamming.

For multiple perforations repeat the above procedure.

Shaft support blocks are mounted on the top and bottom shafts. If they are in a position that obstructs perforating, they can be slid along just enough to clear the hubs.

They should be mounted as near to the centre of the machine as possible, to maximise support. The depth of perforation can be adjusted by first loosening the socket set screws, in the support block, with a 2.5mm allen key. Insert the 2.5mm

allen key into the grub screw, push the allen key up to decrease the perforating depth or down to increase the depth of perforation. Re-tighten the socket set screws.

(Note. This adjustment can also be carried out on the bottom shaft)

2

Typical set-up for perforating sheets.

1 6 8

3

4 5 7 8

FIG 17.1

1 -

2 -

3 -

4 -

Perforating drive wheel with mounted blades

Perforator stripper

Standard drive wheel

Drive wheel with mounted anvils

5 -

6 -

7 -

8 -

Standard drive hub

Upper shaft support block

Lower shaft support block

Grub screw

Always remove blades and anvils once the perforating operation has been completed to avoid marking on digital or delicate media.

Page 34

CREASING

AutoCreaser Pro 50

The Blade Assembly

Adjusting the blade pressure (no paper required)

1. (i) Switch the power ‘on’ by turning the Emergency stop button clockwise to release the safety latch.

(ii) Select the Tools tab change to that shown below.

at the bottom of the touch screen, the display will

(iii) Select the up arrow to move the blade to the Top Dead Centre position.

Click on Up Arrow to put Anvil into Top

Dead Centre position

(TDC)

2. Raise the exit guard

3. Using a 6mm allen key, unlock the shoulder bolts (labelled with scale transfer) positioned at each end of the creasing blade.

4. Turn the adjustment cam to adjust the blade pressure. Increasing the gradient on the scale will increase the blade pressure.

5. Ensure that the shoulder bolts are locked after setting.

The diagram below demonstrates the adjustment of the blade pressure

SYSTEM

Page 35

The Blade Assembly

Adjusting the blade alignment

It is extremely important that the blade and anvil assembly within the creasing unit is correctly aligned. Misalignment of the blade or anvil can lead to damaged profiles and subsequently poor quality creasing so it must, therefore, be corrected immediately.

If the blade set is misaligned, the media being driven will be subject to scoring or even tearing at any point along the crease line.

Please note that to avoid damage to the blade set, adjustment should only be made in small increments.

demonstrates how the blade alignment can be carried out.

The below sketch

Adjustment can be made at either of the blade or anvil. The two clearance holes positioned above the roller tilt mechanism are the front alignment (one for blade, one for anvil).

The two holes are repeated on the back of the machine for the back alignment.

1. Remove the stacker unit from the machine

2. Unlock and centralise the roller tilt mechanism in order to locate the heads of the front alignment screws.

3. Using a 3mm allen key, loosen the cap head type locking screws located on the front face at both ends of the blade /anvil as shown below.

4. Using a 4mm allen key, locate the two front or back alignment screws in the side frame in order to adjust the blade / anvil.

5. The upper screw of the two, will adjust the upper blade / anvil whereas the lower screw will adjust the lower blade / anvil both in very small increments.

6. In order to obtain the required position, adjust either the blade or the anvil by a small amount and then operate the machine to test the form of the crease.

Repeat the exercise until centralisation is located.

7. Using a 3mm allen key, lock the cap head type screws (as per step 3) on both the upper and lower blade / anvil.

Page 36

CREASING

AutoCreaser Pro 50

Replacing Blade Set

1.

2.

Before removing the blade assembly, ensure that the lower blade / anvil is NOT at ‘top dead centre’, Switch the machine off.

Remove the stacker unit and lift the exit guard.

Blade Extractor Tools

3.

Using a 6mm allen key, loosen the socket head screws located inside the blade adjustment cams. Remove the screws and the blade adjustment cams.

4.

Insert the blade extractor tools (70-055-01 &

70-055-02) into the holes in the adjustment links, as shown. Push downwards on the handles of the blade extractor tools to release the blade assembly from the power links.

5. Slide the blade assembly out of the creasing unit and lay it on a flat surface.

6. Slide the adjustment links away from the dowels located in the ends of the blades / anvils as shown in the photograph (left)

7. Place the new blade set into position.

Check that the eccentric shoulder bolts on the link plates have been positioned as shown in fig 20.1.

8. (Upper blade / anvil only)

Slide the adjustment links onto the dowels.

FIG 20.1

SYSTEM

Page 37

The Blade Assembly

9. Slide the new blade set into the slots of the creasing unit as shown in fig. 21.1.

FIG 21.1

NOTE.

The blade set can be fitted with the ANVIL at the bottom or with the ANVIL at the top.

The blade set is supplied from the factory with the ANVIL at the bottom as shown in

FIG22A.

The blade set can be changed to have the ANVIL at the top (as shown in FIG22B), this can improve the repeatability of the fold relative to the crease for certain fold types or when using lighter stocks.

FIG22A FIG22B

Locate the blade extractor tools into the holes in the adjustment links as shown. Pull the handles of the blade extractor tools upwards to engage the blade assembly back into the power links.

10. Set the cam graphics for both ends of the blade / anvil to their lowest point on the scale (ie. When the mark on the scale reaches the mark on cam holder) Fasten the socket head screws on the adjustment cams until they are tight.

Page 38

CREASING

AutoCreaser Pro 50

Replacing Blade Set

11. Push the exit guard down and replace the stacker assembly before operating the machine.

12. Switch the machine on and test the crease for form.

If the pressure and the alignment of the crease is not to a satisfactory level, see pages 33 - 35 to adjust the creasing line.

‘Spares’ kits

In the event of any damaged or lost components within the blade assembly, spares kits are available on request. However, components within the blade set can not be ordered separately ie single blade or anvil.

The following Blade sets are supplied with the Autocreaser Pro 50 as standard.

Standard Blade set Part number 76 - 237 - 02

Consisting of a standard blade and anvil, blade brushes, blade links and alignment bolts.

When running lighter stocks it is recommended that an this can be purchased from Morgana Systems Ltd,

Narrow Blade Set

is used,

Part number 76-237-03

.

SYSTEM

Page 39

Trouble Shooting

Paper crease out of square

l

Check that the sheets are all square and exactly the same size before loading the stack on to the table.

l

Check that the roller tilt mechanism is correctly set and locked in position.

l

Check that the adjustable side lay has been correctly positioned ie. No further than

0.5mm from the paper stack.

Paper jamming

l Check that the leading edge of the paper is not being damaged by the paper gate. If this is occurring, check that the suction slot and the paper gate have been correctly set.

l Check that the first crease position is not too close to the leading edge of the paper.

A minimum distance of 32mm is recommended.

Machine will not start

l

Check the power supply to the machine.

l

Check that the emergency stop button has been released.

l l

Check that the exit guard is down.

Check that the stacker unit is located correctly and has not been disconnected from the magnetic switch.

l Check that the lower blade / anvil is connecting to the home switch (mounted below the lower blade / anvil).

Paper not feeding

l Check that the paper stack is not too high or too heavy for the feeder. The height of the paper stack should be defined by the weight and the size of the stock being creased.

l l

Ensure that the adjustable side lay is not pressed against the paper stack. However, if the clearance between the adjustable side lay and the paper stack is too great, the air supply will escape instead of blowing through the paper thus making it difficult to feed.

Check that the clearance between the paper gate and the suction roller is not set too low.

l On digital media, the feeding performance may be improved if the leading edge of the stack is trimmed before loading onto the Machine.

Page 40

CREASING

AutoCreaser Pro 50

Trouble Shooting

l

Check that the air distribution has been correctly set.

l Check that the air separation has been set high enough to feed the sheets.

l For heavy stocks, very small or very large sheets, embossed or even irregular stock, it may be required to feed the sheets manually - see page 29 for instructions.

Machine not counting

Open the exit and remove the blade set

(see pages 37-39) to access the dual sensor post located in between the drive rollers. Using a soft brush, clean the visible sensor on the end of the post.

Use the brush to clean the sensors between the post and the bottom paper guide which are not visible.

Photograph (left) shows the dual sensor post containing the sensors.

Paper jammed under paper gate.

If paper gets jammed under the paper gate the vacuum drum will stop rotating, this is a safety feature. Remove the paper and re-adjust the paper gate.

SYSTEM

Page 41

Trouble Shooting

Error Screens

Sheet did not arrive.

If the machine stops and error message 01 is displayed on the touch screen, this indicates that the paper did not arrive at the end of the suck process; so the machine timed out. Press the green tick button and then press the start button.

Paper Crunch

If the machine stops and error message 02 is displayed on the touch screen, this indicates that a paper jam has been detected.

Press the system switch down and then select the right or left arrows, to inch the paper forwards or backwards. See page 29 that describes how to remove paper jams.

Press the green tick button and then press the start button.

This error message could also mean that the crunch sensors are faulty or need cleaning.

Double Sheet Feed

If the machine stops and error message 03 is displayed on the touch screen, this indicates that a double sheet feed has been detected. Check that the paper gate has been set correctly. Press the green tick button and then press the start button.

Page 42

CREASING

AutoCreaser Pro 50

Trouble Shooting

Error Screens (Continued)

Blade Not Home

If the machine stops and error message 04 is displayed on the touch screen, this indicates that the lower blade / anvil has not made contact with the HOME switch.

i.e. blade still in top position. Switch the machine off and remove the blade set and ensure that the area is free from obstructions. Return the blade set to the creasing unit and switch the machine on. Operate the machine in the normal sequence, if the display continues to read error message 04 it is advised to contact a Service Engineer immediately.

Overlap

If the machine stops and error message 13 is displayed on the touch screen, this indicates that the ‘Lead Edge Sensor’ has seen a sheet subsequent to the first one as being longer. Again this could actually be a longer sheet, OR it could be a sensor problem (if it is a recurring problem). Check that the paper gate has been set correctly.

Lead E dge Sensor Blocked

If the machine stops and error message 60 is displayed on the touch screen, this indicates that the lead edge sensor is blocked.

Press the system switch down and then select the right or left arrows, to inch the paper forwards or backwards.

Press the green tick button and then press the start button.

This error message could also mean that the lead edge sensors are faulty or need cleaning.

SYSTEM

Page 43

Trouble Shooting

Error Screens (Continued)

Clean Lead Edge Sensor - Warning Screens.

1. The Clean Lead Edge Sensor warning screen, shown below, will appear when the

Run button is pressed and the strength of the Lead Edge Sensor Beam is at about

50% (i.e. the slider is at about the mid-point position along the Indicator Scale).

SENSOR CLEANING WARNING SCREEN

Press the Tools button to clean the

Sensors, as described on Pages 45 & 46.

Press the Run button to ignore the Warning, and continue running the job.

2. The Clean Sensor, Error 65 warning screen, shown below, will appear if the strength of the Lead Edge Sensor Beam is allowed to get down to about 25%. The Lead Edge

Sensors should ideally be cleaned before this warning screen appears.

NOTE.

The Lead Edge Sensors can be cleaned at any time by selecting the Tools Tab at the bottom of the Touchscreen and cleaning the Sensors as described on Pages 45 &

46.

Page 44

CREASING

AutoCreaser Pro 50

Trouble Shooting

Error Screens (Continued)

Lead Edge Sensor Cleaning.

Select the Tools menu on the Touchscreen Display, and then select the clean sensor icon

The screen now shown is a visual indication of the strength of the Lead Edge Sensor beam.

FLASHING (GREEN/BLACK) TO

INDICATE THAT THE SOFTWARE

IS INTERROGATING THE SENSOR

BEAM

SLIDER

INDICATOR SCALE

The vertical indicator scale is divided into four sections, the position of the slider indicates the strength of the beam. The strength of the beam is at its strongest towards the top half of the indicator scale (green) and at its weakest towards the bottom half of the indicator scale

(red). Note the position of the slider on the indicator scale and then clean the sensors as described on Page 46.

NOTE:-

This vertical indicator scale is repeated as a horizontal indicator scale on the right hand side of the Touchscreen Display as shown below.

HORIZONTAL INDICATOR SCALE

SYSTEM

Page 45

Trouble Shooting

Error Screens (Continued)

To clean the lead edge sensors open the exit guard to expose the blade set. Using the

Sensor Cleaning Brush (Morgana part number 601-185), supplied in the dispatch kit, insert the brush between the blade brushes and the top and bottom blades to reach the upper and lower lead edge sensors. (See FIG.1 and FIG.2 below). Move the brush backwards and forwards several times across the sensors to clean them. Note the position of the slider on the indicator scale; the slider should have moved nearer to the top of the scale, indicating that dust has been removed from the sensors. This sensor cleaning operation can be repeated again to see if the sensor beam strength can be further improved. The

Sensors can also be cleaned with a can of compressed air purchased from Farnell (Farnell

Part No. 166-3191), or an equivalent product.

Page 46

CREASING

AutoCreaser Pro 50

Trouble Shooting

Recommended weekly operator maintenance

l l l l

Clean all sensors

Clean in feed rollers and output drive hubs using the cleaning kit provided

(Cleaning kit part number 90-018)

Remove and clean the blade assembly

With the blade assembly removed, clean the slots and surrounding area within the creasing unit.

Technician Maintenance

It is recommended that your machine is fully serviced at least once every six months by a factory trained Service Engineer.

SYSTEM

Page 47

7-95-29

DISPATCH KIT

ITEM PART NUMBER QTY

1 70-171

DESCRIPTION

1 OPERATORS MANUAL -

AUTOCREASER Pro 50 (CB)

1 ROLLER CLEANING KIT 2 90-018

3

650-040 1 POWER CORD CE UK C19 3Pin 16A 2.5Mtrs.

4

5

403-01-030-006

409-01-040-004

6

7

620-007

620-020

8 620-004

9

10

11

620-026

620-028

620-033

12 624-018

13

14

70-055-01

70-055-02

15

16

08-041-02

1-99-12

12 SCREW - SOCKET CAP HEAD - M3 x 6 LG

1 SCREW - SKT. SET FLAT PT. - M4 x 4 LG

1 HEXAGON BALL DRIVER 2mm

1

HEXAGON BALL DRIVER 2.5mm

1 ALLEN KEY 4mm

1 BONDUS L WRENCH 4mm

1 BONDUS L WRENCH 3mm

1 BONDUS L WRENCH 6mm

1 DISPATCH BOX

1 BLADE EXTRACTION TOOL - OP SIDE

1 BLADE EXTRACTION TOOL - LAY SIDE

1 SLITTING ANVIL - UNDERSIZE.

1 SLITTER PERF BLADE 28T

WARNING......

THE BLADES FOR ANVIL AND PERFORATING SETS ARE SUPPLIED AS

MATCHING PAIRS AND SHOULD NOT BE MIXED OR LEFT

UNPROTECTED OR SERIOUS DAMAGE MAY RESULT.

Page 48

CREASING

AutoCreaser Pro 50

ITEM

3

4

1

2

5

6

7

ACCESSORIES AND OPTIONS

PART NUMBER

1-99-10

1-99-12

1-99-41

1-99-35

76-237-03

70-134

172-04-01

DESCRIPTION

PERFORATING BLADE SET 20T (Card)

PERFORATING BLADE SET 28T (Single sheets)

PERFORATING BLADE SET 56T (Fine perforations)

ANVIL SET USED WITH ABOVE BLADE SETS

BLADE SET - NARROW

ANTI-STATIC KIT - AUTOCREASER 50 Mk4

NARROW SHEET KIT

ACCESSORIES....

....May be obtained from your dealer and fitted to your machine using the instructions supplied, or by reading your operators manual.

OPTIONS....

....May also be obtained and fitted by your dealer. You should not attempt to fit options as specialist tools and knowledge are required.

SYSTEM

Page 49

RECOMMENDED SPARES

76-272

655-015

655-016

76-230-02

76-155

76-154

76-156

98-013-03

609-022

606-035

76-109

76-237-02

76-042

607-042

607-048

608-019

76-082

76-083

76-177-02

76-175-02

76-019-02

78-013

613-351

613-191

PART NUMBER

93-021

607-017

609-011

94-028

613-365

652-011

75-500-06

75-430-01

174-06-01

174-19-01

125-21-02

75-06-02

DESCRIPTION

FEED BELT

TIMING BELT - 120XL 037

‘O’ RING Ø20

LOCK PIN ASSEMBLY - Side Lay

EMERGENCY STOP SWITCH

SWITCH - LOW CURRENT COIL - BLACK ROCKER

MINI ITX MOTHERBOARD - A/C PRO 50

CONTROL PCB ASSEMBLY

SMALL STEPPER DRIVER - LOW POWER - PCB ASSY

RS232 ADAPTOR PCB ASSY

DUAL STEPPER DRIVER PCB ASSEMBLY

TOUCHSCREEN ASSY - 7” (NEW CONTROLLER)

PSU ASSEMBLY - ATX12V - 300W

PSU UNIT - SWITCH MODE - 24V

PSU UNIT - SWITCH MODE - 48V

PAPER GUIDE ASSEMBLY - Bottom Sensor

PAPER JAM SENSOR ASSEMBLY

UPPER SENSOR ASSEMBLY

BLADE POSITION SENSOR LEAD

ANTI-STATIC BRUSH

‘O’ RING Ø32

KNOB - Roller Tilt

POWER LINK BEARING

BLADE SET - Standard

DRIVE BELT - FEED BED

TIMING BELT 160XL

TIMING BELT TWIN GRIP - 200 DXL 050

SHOULDER BOLT

PERFORATOR - DRIVE HUB ASSEMBLY

PERFORATOR - DRIVE WHEEL

INPUT ROLLER - Upper

INPUT ROLLER - Lower

OUTPUT SHAFT - Wide

PERFORATOR STRIPPER ASSEMBLY

MICRO SWITCH - Guard Circuit

MICRO SWITCH - Home Circuit

Page 50

CREASING

AutoCreaser Pro 50

RECOMMENDED SPARES

PART NUMBER

75-040

602-056

602-085

76-145-02

76-148-01

76-148-02

76-149-01

76-150-01

76-255

75-427

609-024

175-28-01

76-240

76-241

681-020

681-011

681-015

652-047

75-530-01

DESCRIPTION

STACKER SWITCH ASSEMBLY

BEARING-DRAWN CUP NEEDLE ROLLER-Ø15XØ21X12

BEARING-DRAWN CUP NEEDLE ROLLER Ø10XØ14X10

GAP CONTROL HUB - LAY SIDE

GAP SET LEVER ASSY - OP SIDE

GAP SET LEVER ASSY - LAY SIDE

LOCKING LINK - GAP CONTROL

LOCKING KNOB - GAP CONTROL

LEAD - FOLD COMPENSATION SENSOR

LEAD - VALVE SENSOR

‘O’ RING Ø6 x Ø2.5

BUTTERFLY VALVE

STEPPER DRIVE MOTOR ASSEMBLY

STEPPER BLADE MOTOR ASSEMBLY

FUSE 500mA - AntI-surge

FUSE 315mA - Anti-surge

FUSE 4A - Anti-surge

FUSE 15A - Anti-surge

TRANSFORMER ASSEMBLY 230V TO 110V

NOTE.....

The items listed above represent parts which are subject to wear, loss, or accidental damage, and is included for your guidance only.

Replacement of parts fitted to your machine require specialist knowledge and should therefore be entrusted to your dealer.

SYSTEM

Page 51

FUSE POSITIONS & RATINGS

(POSITION ET CLASSIFICATION DES FUSIBLES)

TRANSFORMER ASSY.

T500mAH 250V (681-020)

PSUs (24V & 48V)

(FUSIBLE PSUs (24 V & 48 V)

T4.0AH 250V (681-015)

ANTI-STATIC UNIT

(IF FITTED)

(FUSIBLE ANTI-STATIQUE

(si installé)

T315mAH 250V (681-011)

MAINS IN

F15AH 250V (652-047)

Page 52

CREASING

AutoCreaser Pro 50

PRODUCT RECYCLING & DISPOSAL

European Union

Disposal Information for Commercial Users

Application of this symbol on your equipment is confirmation that you must dispose of this equipment in compliance with agreed national

Procedures.

In accordance with European legislation end of life electrical and electronic equipment subject to disposal must be managed within agreed procedures.

Prior to disposal please contact your local dealer or representative for end of life take back information.

Disposal Information for Domestic Users

Application of this symbol on your equipment is confirmation that you should not dispose of the equipment in the normal household waste stream.

In accordance with European legislation, end of life electrical and electronic equipment subject to disposal must be segregated from household waste.

Private households within EU Member States may return used electrical and electronic equipment to designated collection facilities free of charge. Please contact your local disposal authority for information.

In some Member States when you purchase new equipment your local retailer may be required to take back your old equipment free of charge. Please ask your retailer for information.

Other Countries

Please contact your local waste authorities and request disposal information.

SYSTEM

Page 53

REVISION HISTORY

Rev.

Mod No.

4 ECO2809

Mod Description

Screen shot graphics changed to show the Lead Edge Sensor Indicator

Bar, on all relative pages. New pages inserted to describe how to use the

Cover Crease Mode for Perfect Bound Covers. (Pages 14 & 15). New pages inserted to show the Clean Lead Edge Sensor Warning Screens and how to clean the Lead Edge Sensors. (Pages 44 to 46)

Date Mod By

02/01/13 BAL

Page 54

CREASING

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement