Agilent PNA Series Microwave Network Analyzers

Agilent PNA Series Microwave Network Analyzers
Agilent
PNA Series
Microwave Network Analyzers
Configuration Guide
PNA-L N5230A
PNA-L N5230A
PNA-X N5242A
PNA E8362B
PNA E8363B
PNA E8364B
PNA E8361A
PNA N5250A
300 kHz to 6, 13.5, or 20 GHz
10 MHz to 20, 40, or 50 GHz
10 MHz to 26.5 GHz
10 MHz to 20 GHz
10 MHz to 40 GHz
10 MHz to 50 GHz
10 MHz to 67 GHz
10 MHz to 110 GHz
System configuration summary
Full S-parameter measurements
This summary lists the main components required to form a
basic measurement system. Options or peripherals may be added
to provide enhanced measurement and data storage capability.
• Agilent PNA Series microwave
network analyzers
• Test port cables, 50 ohms
• Calibration kit for applicable
connector type
This configuration guide describes standard configurations,
options, accessories, upgrade kits and compatible peripherals
for the PNA Series microwave network analyzers. This guide should
be used with the Agilent PNA Series Microwave Network Analyzers
Data Sheet for a complete description of these analyzers.
PNA-L (N5230A)
Step 1: Select N5230A model number
Step 2: Choose your frequency range and test set
(Mandatory, choose only one)
Description
Ordering number
300 kHz to 6 GHz
300 kHz to 6 GHz
300 kHz to 13.5 GHz
300 kHz to 13.5 GHz
300 kHz to 13.5 GHz
300 kHz to 13.5 GHz
300 kHz to 13.5 GHz
10 MHz to 20 GHz
10 MHz to 20 GHz
300 kHz to 20 GHz
300 kHz to 20 GHz
300 kHz to 20 GHz
10 MHz to 40 GHz
10 MHz to 40 GHz
10 MHz to 50 GHz
2-port standard test set
2-port configurable test set
and extended power range
2-port standard test set
2-port configurable test set
and extended power range
4-port standard test set
4-port configurable test set
and extended power range
4-port configurable test set,
extended power range and
internal second source
(Option 080 recommended)
2-port standard test set
2-port configurable test set
and extended power range
4-port standard test set
4-port configurable test set
and extended power range
4-port configurable test set,
extended power range and
internal second source
(Option 080 recommended)
2-port standard test set
2-port configurable test set
and extended power range
2-port standard test set
10 MHz to 50 GHz 2-port configurable test set
and extended power range
N52300-020
N52300-025
N52300-120
N52300-125
N52300-140
N52300-145
N52300-146
N52300-220
N52300-225
N52300-240
N52300-245
N52300-246
N52300-420
N52300-425
N52300-520
N52300-525
Step 3: Choose additional software options (Optional)
Description
Ordering number
Time domain for 6 GHz model
N52310-010
Time domain for 13.5, 20, 40 or 50 GHz model
N52300-010
Frequency-offset measurements
N52300-080
Scalar-calibrated converter measurements
N52300-082
(Option 080 required)
4-port measurement application
N52300-550
N-port capabilities for 6, 13.5 or 20 GHz model
N52310-551
N-port capabilities for 40 or 50 GHz model
N52300-551
Step 4: Choose an electronic or mechanical calibration kit
(Optional)
Description
Ordering number
300 kHz to 9 GHz, 2-port, 3.5 mm
85093C
300 kHz to 13.5 GHz, 4-port, Type-N
N4431B
or 3.5 mm
300 kHz to 18 GHz, 4-port, Type-N
N4432A
300 kHz to 20 GHz, 4-port, 3.5 mm
N4433A
300 kHz to 26.5 GHz, 2-port, 3.5 mm
N4691B
10 MHz to 50 GHz, 2-port, 2.4 mm
N4693A
Note: For additional calibration kits refer to page 16
Step 5: Accessories (Optional)
Description
Rack mount kit without handles
Rack mount kit with handles
USB CD R/W drive
USB Hub
Ordering number
N5230A-1CM
N5230A-1CP
N4688A
N4689A
Note: For additional accessories refer to page 16
Step 6: Calibration documentation (Optional)
Description
Ordering number
ISO 17025 compliant calibration
N5230A-1A7
Commercial calibration certificate with test data N5230A-UK6
ANSI Z540 compliant calibration
N5230A-A6J
Step 7: Choose your warranty and service (Optional)
Description
1 year return-to Agilent warranty and service
3 year return-to Agilent warranty and service
Documentation
The PNA Series instruments are equipped with an Online Help
system available within the instrument in the following languages: English, Japanese, Chinese, German, Spanish, and French.
The PNA Service Guide and Online Help system are available on
the Web: www.na.tm.agilent.com/pna
Connector type
Option 020, 025, 120, 125, 140, 145, 146, 220, 225, 240, 245, 246:
3.5 mm ruggedized male, 50 ohm
Option 420, 425, 520, 525:
2.4 mm ruggedized male, 50 ohm
Additional product information
For additional PNA-L (N5230A) product information, refer
to the PNA-L brochure available on our Web site:
www.agilent.com/find/pnal
2
PNA-L (N5230A)
This guide is intended to assist you in the ordering process.
Additional information and products (such as calibration kits and
cables) are described throughout this document.
4-port standard test set
Test set options
PORT 4
• Standard test set and power range (Option xx0)
The 13.5 and 20 GHz versions are available in 2- or 4-ports.
• Configurable test set and extended power range (Option xx5)
Adds front panel access loops and one or two 60 dB step
attenuators as shown in the figures below. This provides the
capability to improve instrument sensitivity for measuring
low-level signals, to reverse the directional couplers to achieve
even more dynamic range or to add components and other
peripheral instruments for a variety of measurement applications.
The 13.5 and 20 GHz versions are available in 2- or 4-ports.
• Configurable test set, extended power range and internal
second source (Option x46)
Available with 4-port models only, this option adds an internal
second source, nine front panel access loops and two 60 dB
step attenuators as shown in the figure below. This provides an
additional signal (fixed or swept) for two-tone third-order-intercept
(TOI) and intermodulation testing of amplifiers; or it can be used
as a fast swept-LO signal for fixed-IF testing of mixers and
converters. In either case, sweep speed is more than twenty times
faster than using an external source (Option 080 recommended.
Please note, Option 080 is needed in order to have independent
control of the two internal sources.).
D
PORT 3
Switch
B
Reference
receiver
PORT 2
R
A
PORT 1
4-port configurable test set and
extended power range
Source out
Coupler thru
PORT 4
Coupler arm
Receiver D in
D
Source out
Coupler thru
PORT 3
Switch
Source
2-port standard test set
C
Source
Coupler arm
Receiver C in
C
60 dB
B
Receiver B in
Coupler arm
Source
PORT 2
Coupler thru
Source out
R
Reference
receiver
Switch/splitter
A
R1
Reference
receiver
Reference
receiver
Receiver A in
Coupler arm
R2
PORT 1
Coupler thru
Source out
A
Source out
Receiver R in
B
Measurement
receivers
Port 1
4-port configurable test set, extended
power range and internal second source
Port 2
2-port configurable test set and
extended power range
Source 2
Source 1
60 dB
Source
60 dB
R
Switch/splitter
R1
Reference
receiver
Reference
receiver
A
R2
60 dB
B
C
D
60 dB
A
B
Measurement
receivers
Source Rcvr SRC
out R1 out
in
Cplr
thru
Port 1 Cplr Rcvr
arm
A
in
Rcvr Cplr
B
arm
in
Port 2
Cplr
thru
SRC Rcvr Source
out R2 out
in
Test port 1
Test port 2
Test port 3
Test port 4
3
PNA-L (N5230A)
Additional options
Certification options
This option enables the PNA Series to view reflection and transmission responses in both time or distance domain. Use time
domain to tune filters, gate out the response of fixtures and
cables, characterize the impedance of transmission line, and more.
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes calibration label, calibration
certificate, and data report. Conforms to ISO 9001.
□ Time domain (Option 010)
□ Frequency offset (Option 080)
□ Commercial calibration certification with test data (Option UK6)
□ ISO 17025 compliant calibration (Option 1A7)
This option enables the PNA Series to set the source frequency
independently from where the receivers are tuned. This ability
is important for two general classes of devices: mixers (and
converters) and amplifiers.
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes calibration label, ISO 17025
calibration certificate, and data report, measurement uncertainties
and guardbands on all customer specifications. Conforms to ISO
17025 and ISO 9001.
□ Scalar-calibrated converter measurements (Option 082)
□ ANSI Z540 compliant calibration (Option A6J)
With a simple setup and calibration, this application provides the
highest accuracy for conversion-loss (or gain) measurements by
combining one-port and power-meter calibrations to remove
mismatch errors. Option 080 required.
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes pre- and post-adjustment data
with measurement uncertainty information compliant to the
ANSI/NCSL Z540 standard.
□ 4-port measurement application (Option 550)
Enables full 4-port error correction and differential measurements
on a 2-port network analyzer with configurable test set (Option x25).
External test set required. User installable.
□ N-port capabilities (Option 551)
Adds full N-port error correction and measurement capabilities
to any PNA-L network analyzer with configurable test set (Option
xx5 or x46). External test set required. User installable.
4
PNA-X Network Analyzers N5242A , 10 MHz to 26.5 GHz, 2 or 4 Ports
Options
To add options to a product, order the corresponding item number.
Test set
Option 200
Option 224
Option 400
Option 423
Description
For N5242A
Additional information
2 ports, single source
2 ports, add internal 2nd source, combiner and mechanical switches
4 ports, dual source
4 ports, add internal combiner and mechanical switches
N5242A-200
N5242A-224
N5242A-400
N5242A-423
Requires Options 200, 219 and 080
Recommends Option 080
Requires Options 400, 419, and 080
Power configuration
Option 219
2 ports, extended power range and bias-tees
Option 419
4 ports, extended power range and bias-tees
Option H85
High-power configuration
Measurement applications
Option 010
Time-domain measurements
Option 0291
Fully-corrected noise figure measurements
N5242A-219
N5242A-419
N5242AH85
N5242A-010
N5242A-029
Option 080
Option 0822
Option 0832
Option 084
Frequency offset
Scalar-calibrated converter measurements
Vector- and scalar-calibrated converter measurements
Embedded LO measurements
N5242A-080
N5242A-082
N5242A-083
N5242A-084
Option 086
Gain compression application
N5242A-086
Option 5513
N-port capabilities
N5242A-551
Pulse, antenna, mm-wave
Option H08
Pulse measurements
Option 020
Add IF inputs for antenna and mm-wave
Option 021
Add pulse modulator to internal 1st source
Option 022
Add pulse modulator to internal 2nd source
Option 025
Add four internal pulse generators
N5242A-H08
N5242A-020
N5242A-021
N5242A-022
N5242A-025
Accessories
Option 1CM
N1966A
N4688A
N4689A
Rack mount kit for use without handles
Pulse I/O adapter
USB CD R/W drive
USB Hub
N5242A-1CM
N1966A
N4688A
N4689A
Perpetual license for built-in performance test software for
Agilent inclusive calibration
Perpetual license for built-in performance test software for
standards compliant calibration
N5242A-897
Calibration Software
Option 8974
Option 8984
Calibration documentation
Option 1A7
ISO 17025 compliant calibration
Option UK6
Commercial calibration certificate with test data
Option A6J
ANSI Z540 compliant calibration
Requires Option 200
Requires Option 400
Requires one of these options: 219,
224, 419 or 423
Requires Option 080
Requires Option 080
Requires Options 080 and 083,
requires firmware A.07.50 and above
Recommend Options 219 or 419,
requires firmware A.08.00 and above
Requires Option 025
Requires Options 224 or 400
N5242A-898
N5242A-1A7
N5242A-UK6
N5242A-A6J
1. In addition to the list of required PNA-X options, Option 029 requires an N4691B ECal module for use as an impedance tuner,
and an Agilent 346 series noise source for calibration.
2. Option 082 is a subset of Option 083, and therefore, they can not be ordered together.
3. When configured as a multiport analyzer with Option 551, the combiner feature of Option 224 or 423 is not available.
When configured as a standalone analyzer, the combiner feature is available.
4. Additional hardware required. Please refer to chapter 2 of the Service Guide for required service test equipment.
5
PNA-X Network Analyzer
The PNA-X is an integrated vector network analyzer featuring a
built-in S-parameter test set, one or two synthesized sources
used for device stimulus, a hard disk drive, USB interfaces, and a
10.4” LCD touch screen display. The N5242A analyzer has 50 ohm,
ruggedized 3.5 mm (m) test ports. Included with each instrument
is a mouse, keyboard (U.S. style), and a 1-year return-to-Agilent
service warranty.
● N5242A
network analyzer, 10 MHz to 26.5 GHz,
2 or 4 ports
Test set options
• 2-port standard test set and power range (Option 200)
The standard 2-port test set comes with six front-panel access
loops. The loops provide access to the signal path between
(a) the source output and the reference receiver, (b) the source
output and directional coupler thru arm and (c) the coupled
arm of the directional coupler and the port receiver. The standard
test set also includes a solid-state internal RF transfer switch
in the R1 reference-receiver path.
• 4-port standard test set, power range and an internal second
source (Option 400)
The standard 4-port test set comes with 12 front-panel access
loops and a built-in second source. The loops provide access to
the signal path between (a) the source output and the reference
receiver, (b) the source output and directional coupler thru arm
and (c) the coupled arm of the directional coupler and the port
receiver. The internal second source provides an additional signal
(fixed or swept) for two-tone third-order-intercept (TOI) and
intermodulation testing of amplifiers, or it can be used as a fast
swept-LO signal for fixed-IF testing of mixers and converters.
With two sources, source 1 is accessible through test ports 1
and 2, and source 2 is accessible through test ports 3 and 4.
The standard test set also includes a solid-state internal RF
transfer switch in the R1 reference-receiver path. Recommends
Option 080.
6
• Extended power range and bias-tees (Option 219, 419)
Adds to the standard test set one 65 dB source attenuator
(settable in 5 dB increments), one 35 dB receiver attenuator
(settable in 5 dB increments), and one bias-tee to each test
port. Option 219 requires Option 200, and Option 419 requires
Option 400.
• Add an internal second source, a combiner and mechanical
switches to 2-port analyzer (Option 224)
Available with 2-port model only, this option adds an internal
second source, a combiner and mechanical switches. The
internal second source provides an additional signal (fixed or
swept) for two-tone third-order-intercept (TOI) and intermodulation
testing of amplifiers, or it can be used as a fast swept-LO signal
for fixed-IF testing of mixers and converters. The mechanical
switches provide increased flexibility by having rear panel
access to signal paths for advanced applications. Access to the
second source is available through two output (SMA) connectors
on the front panel. Requires Options 200, 219 and 080.
• Add an internal combiner and mechanical switches to 4-port
analyzer (Option 423)
Available with 4-port model only, this option adds a combiner
and mechanical switches. The mechanical switches provide
increased flexibility by having rear panel access to signal paths
for advanced applications. Requires Options 400, 419 and 080.
PNA-X Network Analyzer
2-port standard test set and power range (Option 200)
Source 1
OUT 2
OUT 1
R2
R1
A
B
Test port 1
Test port 2
2-port extended power range and bias-tees (Option 219, requires Option 200)
Source 1
OUT 1
OUT 2
R2
R1
A
B
35 dB
35 dB
65 dB
65 dB
Test port 1
Test port 2
7
Add an internal second source, a combiner, and mechanical switches to 2-port analyzer
(Option 224 requires Options 200, 219 and 080)
Source 1
OUT 1
Source 2
OUT 2
OUT 1
OUT 2
Rear
panel
R2
R1
A
B
35 dB
35 dB
65 dB
65 dB
Test port 1
Source 2
Output 1
Source 2
Output 2
Test port 2
4-port standard test set, power range, and an internal second source (Option 400, recommends Option 080)
Source 1
OUT 2
OUT 1
Source 2
OUT 1
R3
R1
R4
A
Test port 1
8
OUT 2
R2
C
Test port 3
D
Test port 4
B
Test port 2
4-port extended power range and bias-tees (Option 419, requires Option 400)
Source 1
OUT 2
OUT 1
Source 2
OUT 1
OUT 2
R3
R1
R4
A
R2
C
35 dB
D
35 dB
Test port 1
35 dB
35 dB
65 dB
65 dB
B
Test port 3
65 dB
65 dB
Test port 4
Test port 2
Add an internal combiner and mechanical switches to 4-port analyzer
(Option 423 requires Options 400, 419 and 080)
Source 1
OUT 1
Source 2
OUT 2
OUT 1
OUT 2
Rear
panel
R3
R1
R4
A
C
35 dB
65 dB
Test port 1
R2
D
35 dB
65 dB
Test port 3
B
35 dB
35 dB
65 dB
65 dB
Test port 4
Test port 2
9
2-port PNA-X with noise figure hardware (shown with Options 200, 219, 224, and 029).
On 4-port analyzers (Option 419 or 423) with Option 029, ports 1 and 2 are the same as shown here.
10
PNA-X Network Analyzer
Additional options
□ Pulse measurements (Option H08)
This option provides software to set up and control pulsed-RF
measurements with point-in-pulse and pulse-profile capability.
The software sets the coefficient of the PNA-X’s digital-IF filters
to null out unwanted spectral components, enables the receiver
IF gates on the rear panel, controls internal pulse generators
(Option 025), internal pulse modulators (Option 021 and/or 022)
or external pulse modulators, and optimization for measurement
sensitivity. The measurement software can run on the PNA-X
or an external computer. A “.dll” file containing the IF-filter
algorithms is included for automated pulsed-RF testing. The
N1966A pulse I/O adapter is recommended if using external
pulse generators and/or external pulse modulators.
□ Add four internal pulse generators (Option 025)
This option enables four internal pulse generators. These
pulse generators can be used to control the internal pulse
modulators and internal receiver IF gates, and are also available
on pins 10 through 13 of the Pulse I/O D-sub connector on
the rear panel of the PNA-X to control external modulators
and/or gates. The N1966A pulse I/O adapter is recommended
if using external pulse modulators. (See diagram below for
details of the D-sub connector.)
8
7
15
6
14
5
13
4
12
3
11
2
10
1
9
Pulse I/O D-sub connector (DB-15 female)
□ Time domain (Option 010)
This option enables the PNA-X to view reflection and
transmission responses in time or distance. Use time domain
to tune filters, gate out the response of fixtures and cables,
characterize the impedance of transmission lines and more.
□ Add IF inputs for antenna and millimeter-wave (Option 020)
This option enables external IF inputs on the rear panel of the
PNA-X for applications such as antenna and millimeter-wave
test.
□ Add pulse modulator to internal first source (Option 021)
This option enables the internal pulse modulator on source 1.
Control of the modulator can also be done via pin 8 of the
Pulse I/O D-sub connector on the rear panel of the PNA-X
using an external pulse generator, or by using one of the internal
pulse generators (Option 025). The N1966A pulse I/O adapter
is recommended if using an external pulse generator.
(See diagram below for details of the D-sub connector.)
□ Add pulse modulator to internal second source (Option 022)
This option enables the internal pulse modulator on source 2.
Control of the modulator can also be done via pin 8 of the
Pulse I/O D-sub connector on the rear panel of the PNA-X
using an external pulse generator, or by using one of the internal
pulse generators (Option 025). The N1966A pulse I/O adapter
is recommended if using an external pulse generator. Option 224
or 400 required. (See diagram below for details of the D-sub
connector.)
□ Fully-corrected noise figure measurements (Option 029)
This option adds hardware and firmware for high-accuracy
noise figure measurements, utilizing Agilent’s unique sourcecorrection technique. Using the PNA-X and an Agilent ECal
module configured as an impedance tuner, the effects of
imperfect system source match are removed, greatly improving
the accuracy of the cold-source technique. This approach
surpasses the accuracy provided by the Y-factor method. This
option requires an N4691B ECal module (m-f recommended)
and a 346-series noise source (both must be ordered or supplied
separately). During calibration of the analyzer, an additional
ECal or mechanical calibration kit is required (also must be
ordered or supplied separately). The noise source is only used
during calibration of the analyzer. To use the ECal module as a
tuner, Option 029 includes a cable (N5242-20137) and 3.5 mm
m-f adapter (85052-60013) for use with m-f modules
(N4691B-M0F). For use with f-f ECal modules (N4691B-00F),
order a 3.5 mm m-m adapter (85052-60014).
□ Frequency offset (Option 080)
This option enables the PNA-X to set the source frequency
independently from where the receivers are tuned. This ability
is important for measuring amplifiers, mixers, and frequency
converters.
□ Scalar-calibrated converter measurements (Option 082)
With a simple setup and calibration, this application delivers
the highest accuracy for conversion-loss (or gain) magnitude
measurements by combining one-port and power-meter
calibrations to remove mismatch errors. This application
provides an intuitive and easy-to-use user interface for setting
up mixer and converter measurements, with single or dual
conversion stages (up to two local oscillators, LO), along with
control of up to two external signal generators for use as LO.
External synthesizers supported include the Agilent ESG series
and the PSG series of signal source families as well as other
SCPI controlled signal generators. Option 082 requires Option 080,
and cannot be ordered with Option 083.
11
PNA-X Network Analyzer
□ Vector- and scalar-calibrated converter measurements
(Option 083)
This converter measurement is a superset and includes not
only the scalar-calibrated converter measurement, but
also the vector-mixer calibration (VMC). The advanced and
unique VMC delivers exceptional conversion loss amplitude
and phase accuracy for mixer and converter measurements.
This application provides an intuitive and easy-to-use user
interface for setting up mixer and converter measurements,
with single or dual conversion stages (up to two LO’s), along
with control of up to two external signal generators for use as
LO.External synthesizers supported include the Agilent ESG
series and the PSG series of signal source families as well as
other SCPI controlled signal generators. Option 083 requires
Option 080, and cannot be ordered with Option 082.
□ Pulse I/O adapter (N1966A)
An adapter for connecting between the Pulse I/O connector on
the rear panel of the PNA-X and the coaxial inputs and outputs
of external pulse generators and external pulse modulators.
Coaxial connectors are SMB-male. (See diagram below for
details of the Pulse I/O adapter.
The PULSE IN connectors are for controlling the PNA-X's internal
IF gates, which are enabled with Option H08 and used with
narrowband detection. The PULSE OUT connectors are from the
PNA-X's four internal pulse generators, which are enabled with
Option 025. The PULSE SYNC IN connector is used to synchronize
the internal pulse generators with an external timing pulse. The
RF PULSE MOD IN connector controls the internal pulse modulator(s)
which are enabled with Options 021 and 022.
□ Embedded LO measurements (Option 084)
Advanced software tuning that provides absolute group delay of
converters with embedded LOs without the need for access to a
common reference signal. The measurement result is the same
as locking the DUT LO to the reference mixer LO. (Option 080
and 083 required) Requires firmware A.07.50 and above.
□ Gain compression application (Option 086)
The Gain Compression Application (GCA) provides input power,
output power, gain, and phase at an amplifier's compression
point, over a specified frequency and power range. GCA's
SMART Sweep is very fast and easy-to-use. GCA also includes
a guided calibration that corrects for absolute power levels,
frequency response, and mismatch errors. Requires firmware
A.08.00 and above
□ N-port capabilities (Option 551)1
Adds full N-port error correction and measurement capabilities
to the PNA-X network analyzer. External test set is required.
□ High-power test set (Option H85)
With the standard test set configurations that include source
attenuators, the internal bias tees limit the maximum test port
power to +30 dBm. Option H85 removes the bias tees
between the source attenuators and the test port couplers.
This extends the maximum port power that the analyzer can
safely handle to +43 dBm. Option H85 requires Option 080,
plus Option 224 or 423.
□ Rack mount kit without handles (Option 1CM)
Adds a rack mount (5063-9217) and rail kit (E3663AC) for use
without handles.
1. When configured as a multiport analyzer with Option 551, the
combiner feature of Option 224 or 423 is not available. When configured
as a standalone analyzer, the combiner feature is available.
12
Pulse I/O adapter (N1966A) simplifies connections
PNA-X Network Analyzer
Certification options
□ Commercial calibration certificate with test data (Option UK6)
Complete set of measurements which tests unit to
manufacturer’s published specifications. Includes calibration
label, calibration certificate, and data report. Conforms to ISO 9001.
□ ISO 17025 compliant calibration (Option 1A7)
Complete set of measurements which tests unit to
manufacturer’s published specifications. Includes calibration
label, ISO 17025 calibration certificate, and data report,
measurement uncertainties and guardbands on all customer
specifications. Conforms to ISO 17025 and ISO 9001.
□ ANSI Z540 compliant calibration (Option A6J)
Complete set of measurements which tests unit to
manufacturer’s published specifications. Includes pre- and
post-adjustment data with measurement uncertainty information
compliant to the ANSI/NCSL Z540 standard.
Warranty and service
1 and 3 year warranty and service plans are available at time of
instrument purchase. Standard warranty is 1 year.
13
PNA Network Analyzers1 E8361A/62B/63B/64B, N5250A
PNA
E8362B
E8363B
E8364B
(highest performance series)
10 MHz to 20 GHz
10 MHz to 40 GHz
10 MHz to 50 GHz
PNA
E8361A
N5250A2
(highest performance series)
10 MHz to 67 GHz
10 MHz to 110 GHz
Options
To add options to a product, order the corresponding item number.
Description
Test set
Option 014
• Configurable test set
Power configuration
Option UNL • Extended power range
and bias-tees
Option 016
• Add receiver attenuators
Option H85
• High-power configuration
Non-linear measurements
Option 080
• Frequency offset
For E8362B
For E8363B
For E8364B
For E8361A
For N5250A
system3
E8362B-014
E8363B-014
E8364B-014
E8361A-014
Included
E8362B-UNL
E8364B-UNL
E8364B-UNL
E8361A-UNL
Included
E8362A-016
E8364A-016
E8364A-016
E8361A-016
E8361A-016
E8362B-H85
E8363B-H85
E8364B-H85
Contact
Agilent
Contact
Agilent
E8362A-080
E8364A-080
E8364A-080
E8361A-080
Included
Additional
information
Only E8361A
requires 014
Requires UNL
(only E8361A also
requires 014)
Includes 014, 016,
UNL*4, 080, 081
Requires 014
(E8361A only, 081
required if UNL is
also purchased)
Included
Requires 014, 080
(only E8361A also
requires UNL)
E8361A-0825 Requires 014, 080
Option 081
• Reference receiver switch
E8362A-081
E8364A-081
E8364A-081
E8361A-081
Option 082
• Scalar-calibrated
E8362B-082
converter measurements
• Vector- and scalar-calibrated E8362A-083
converter measurements
E8363B-082
E8364B-082
E8361A-082
E8364A-083
E8364A-083
E8361A-083
E8362B-084
E8363B-083
E8364B-083
E8361A-083
E8361A-0835 Requires 014, 080,
081(only E8361A
also requires UNL)
Requires Option 083
E8362B-H08
E8363B-H08
E8364B-H08
E8361A-H08
E8361A-H085 Requires 014, 080
E8362B-H11
E8363B-H11
E8364B-H11
E8361A-H11
Included
Requires 014, UNL,
080, and 081
E8362A-010
E8362B-550
E8362B-551
E8363A-010
E8363B-550
E8363B-551
E8364A-010
E8364B-550
E8364B-551
E8361A-010
E8361A-550
E8361A-551
E8361A-010
Options 550 and 551
require 014, and are
not compatible with
N5250A systems
Option 083
• Embedded LO Measurement
Option 0846
Pulse, antenna, mm-wave
Option H08
• Pulsed-RF measurement
capability
Option H11
• IF access (for antenna,
pulsed-RF and mm-wave
measurements)
Measurement features
Option 010
• Time-domain capability
Option 550
• 4-port measurement application
Option 551
• N-port capabilities
Accessories
Option 1CM
• Rack mount kit for use
E8362A-1CM
E8363A-1CM
E8364A-1CM E8361A-1CM E8361A-1CM
without handles
Option 1CP
• Rack mount kit for use
E8362A-1CP
E8363A-1CP
E8364A-1CP
E8361A-1CP
E8361A-1CP
with handles
N4688A
• USB CD R/W drive
N4688A
N4688A
N4688A
N4688A
N4688A
N4689A
• USB Hub
N4689A
N4689A
N4689A
N4689A
N4689A
Calibration documentation
Option 1A7
• ISO 17025 compliant
E8362B-1A7
E8363B-1A7
E8364B-1A7
E8361A-1A7
E8361A-1A7
calibration
Option UK6
• Commercial calibration
E8362A-UK6
E8363A-UK6
E8364A-UK6
E8361A-UK6
E8361A-UK6
certificate with test data
Option A6J
• ANSI Z540 compliant
E8362B-A6J
E8363B-A6J
E8364B-A6J
E8361A-A6J
E8361A-A6J
calibration
Note: Item numbers may not correspond to product model number. For example, to order the time-domain option on the E8362B,
the correct item number to order is E8362A-010.
Warranty and service One, and three year warranty service plans are available at time of instrument purchase.
The N5250A 110 GHz system carries a full one-year on-site warranty (where available).
Calibration Three year calibration plans are available at time of instrument purchase.
1. All models are not available in all countries.
2. For more detailed information regarding the 110 GHz network analyzer system, refer to the Agilent Web site: www.agilent.com/find/pna
and download the N5250A Technical Overview, literature number 5988-9620EN.
3. The N5250A 110 GHz system also includes an N5260A millimeter-wave test set controller, 1.0 mm combiner assembly, interconnecting cables,
and installation and productivity assistance. See page 14 for more details.
4. UNL* does not include bias-tees. Only includes source attenuators.
5. Up to 67 GHz.
6. Requires firmware A.07.05 and above plus 1.1 GHz CPU board.
14
Agilent PNA Network Analyzers
The microwave PNA Series instruments are integrated vector
network analyzers equipped with a built-in S-parameter test set,
synthesized source, hard and floppy disk drives, and LCD display.
The E8362B analyzer has two 50 ohm, 3.5 mm (m) test ports.
The E8363B and E8364B analyzers have two 50 ohm, 2.4 mm (m)
test ports. The E8361A analyzer has two 50 ohm, 1.85 mm (m)
test ports. Included with each instrument is a mouse, keyboard (U.S.),
and a 1-year return-to-Agilent service warranty.
● E8362B
● E8363B
● E8364B
● E8361A
● N5250A
network analyzer, 10 MHz to 20 GHz
network analyzer, 10 MHz to 40 GHz
network analyzer, 10 MHz to 50 GHz
network analyzer, 10 MHz to 67 GHz1
network analyzer system, 10 MHz to 110 GHz
□ Extended power range and bias-tees (Option UNL)2
Adds two 60 dB step attenuators and two bias-tees to the
E8362/3/4B. Adds two 50 dB step attenuators and two bias-tees
to the E8361A. A step attenuator and bias-tee set is inserted
between the source and test port one and another set between
the source and test port two. (see PNA Series Microwave Data
Sheet literature number 5988-7988EN for a basic block diagram)
□ Frequency offset (Option 080)2
This option enables the PNA Series microwave network analyzers
to set the source frequency independently from where the
receivers are tuned. This ability is important for two general
classes of devices: mixers (and converters) and amplifiers.
Option 080 provides a very basic user interface.
□ Reference receiver switch (Option 081)2
Options
□ Time-domain capability (Option 010)
For viewing reflection and transmission responses in time or
distance domain.
□ Configurable test set (Option 014)2
Provides six front panel access loops. Three access loops are
for port one and three for port two. The loops provide access
to the signal path between (a) the source output and the
reference receiver, (b) the source output and directional coupler
thru arm and (c) the coupled arm of the directional coupler and
the port receiver. This option provides the capability to improve
instrument sensitivity for measuring low-level signals, to
reverse the directional coupler to achieve even more dynamic
range or to add components and other peripheral instruments
for a variety of measurement applications. (see PNA Series
Microwave Data Sheet literature number 5988-7988EN for a
basic block diagram)
□ 4-port measurement application (Option 550)2
Enables full 4-port error correction and differential
measurements on a 2-port network analyzer with configurable
test set. Option 014 required. External test set required.
□ N-port capabilities (Option 551)2
Adds full N-port error correction and measurement
capabilities to any PNA network analyzer with configurable
test set. Option 014 required. External test set required.
Option 081 adds a solid-state internal RF transfer switch in the
R1 reference-receiver path (see PNA Series Microwave Data
Sheet literature number 5988-7988EN for a block diagram). The
switch allows the instrument to easily switch between standard
S-parameter (non-frequency-offset) measurements and frequency
offset measurements such as relative phase or absolute group
delay that require an external reference mixer. The user can set
the switch manually or remotely, but it is best used with the
frequency-converter application (Option 083), where it is controlled
automatically during the vector-mixer calibration procedure
and subsequent measurements.
□ Scalar-calibrated converter measurements (Option 082)2
With a simple setup and calibration, this application provides
the highest accuracy for conversion-loss (or gain) measurements
by combining one-port and power-meter calibrations to remove
mismatch errors. Option 080 required.
□ Vector- and scalar-calibrated converter measurements
(Option 083)2
This converter measurement adds an intuitive and easy-to-use
user interface, advanced calibration choices that provide
exceptional amplitude and phase accuracy, and control of
external signal sources for use as local oscillators. Mixer
calibration techniques include scalar-mixer calibration and
vector-mixer calibration (requires Option 081). Finally, the
frequency-converter application supports all of Agilent’s major
signal source families.
□ Embedded LO Measurements (Option 084)
Advanced software tuning that provides absolute group delay of
converters with embedded LOs without the need for access to a
common reference signal. The measurement result is the same
as locking the DUT LO to the reference mixer LO. (Options 080
and 083 required) Requires firmware A.07.05 and above plus
1.1 GHz CPU board.
1. The E8361A can be extended to 110 GHz with IF access (Option H11).
2. Up to 67 GHz.
15
□ Add receiver attenuators (Option 016)
An attenuator is added between each test port and its
corresponding receiver. Two 35 dB step attenuators are added
to the E8362/3/4B. Two 50 dB step attenuators are added to
the E8361A (see PNA Series Microwave Data Sheet literature
number 5988-7988EN for a basic block diagram).
□ Pulsed-RF measurement capability (Option H08)2
Provides software to set up and control pulsed-RF measurements
with point-in-pulse capability. The software sets the coefficient
of the PNA’s digital-IF filter to null out unwanted spectral
components, enables the IF gates provided with IF access
(Option H11), and controls selected Agilent pulse generators.
It can be run on the PNA or an external computer. A “.dll” file
containing the IF-filter algorithms is included for automated
pulsed-RF testing. The pulsed application is configured to work
with the Agilent 81110A series pulse generator.
□ High-power test set (Option H85)
This configuration combines options that are often necessary
for high power measurements (UNL*1, 014, 016, 080, 081). The
only difference between ordering Option H85 versus a
combination of the options listed above is the source
attenuator option UNL. Standard UNL includes two source
attenuators and two bias-tees. Option H85 includes the two
source attenuators, but not the bias-tees, as the bias-tees are
the power-limiting factor in the network analyzer test set.
The maximum power at the test port is +43 dBm (<20 GHz), and
+40 dBm (>20 GHz).
Option 080, frequency-offset mode, is included in Option H85
because it manages the phase-locking internally (instead of
depending on the R1 receiver). So if you need to use external
components in the path of the R1 receiver, it makes the
measurements simpler and more robust.
□ Rack mount kit without handles (Option 1CM)
For more detailed information regarding pulsed measurement
capabilities with the microwave PNA refer to the Agilent Web
site www.agilent.com/find/pna and download the PNA Series
MW Network Analyzers Configuration Guide for Pulsed
Measurements, literature number 5988-9833EN.
□ IF access (Option H11)
Provides hardware to enable antenna, point-in pulse, and
broadband millimeter-wave measurements to 110 GHz. For
each of the MW PNA’s measurement receivers, IF gates
(enabled with pulsed measurement capability, Option H08) and
external IF inputs are added. In addition, access to the PNA’s
internal RF and LO source is provided for remote mixing
applications. For basic antenna measurements, only Option H11
is necessary. Pulsed antenna applications also require the
pulsed measurement capability (Option H08). Broadband
measurements to 110 GHz, also requires an N5260A
millimeter-wave test set controller.
Note: Use external IF access for up to 20 dB more sensitivity
when making antenna measurements with a remote mixing
configuration. Add Option H08 (Pulsed-RF Measurement
Capability) to enable advanced pulsed measurements. Or
upgrade to a broadband (10 MHz to 110 GHz) VNA system
simply by purchasing an N5260A controller test set with test
heads (Option 110, 120, or 130).
1. UNL* does not include bias-tees. Only includes source attenuators.
2. Up to 67 GHz.
3. The 5063-9237 kit assumes you have the standard handles shipped
with the instrument. If you do not have handles, order a 5063-9224 kit.
16
Adds a rack mount (5063-9217) and rail kit (E3663AC) for use
without handles.
□ Rack mount kit with handles (Option 1CP)
Adds a rack mount (5063-9237)3 and rail kit (E3663AC) for use
with standard supplied handles.
Documentation
PNA Online Help system is available within PNA instruments in
the following languages: English, German, Spanish, French,
Japanese, and Chinese.
The PNA Service Guide and Online Help are available on the
Web: http://na.tm.agilent.com/pna
E8361A/62B/63B/64B
Configuration Details
Certification options
Selecting the correct mixer-test configuration:
□ Commercial calibration certificate with test data (Option UK6)
Complete set of measurements which tests unit to
manufacturer’s published specifications. Includes calibration
label, calibration certificate, and data report. Conforms to ISO 9001.
□ ISO 17025 compliant calibration (Option 1A7)
Complete set of measurements which tests unit to
manufacturer’s published specifications. Includes calibration
label, ISO 17025 calibration certificate, and data report,
measurement uncertainties and guardbands on all customer
specifications. Conforms to ISO 17025 and ISO 9001.
□ ANSI Z540 compliant calibration (Option A6J)
Complete set of measurements which tests unit to
manufacturer’s published specifications. Includes
pre- and post-adjustment data with measurement
uncertainty information compliant to the ANSI/NCSL
Z540 standard.
Warranty and service
1 and 3 year warranty and service plans are available at time of
instrument purchase. Standard warranty is 1 year.
Most mixer or converter test applications require Options 014, 080,
and 082 for conversion loss/gain, or Options 014, 080, 081 and
083 for conversion loss/gain and phase/delay measurements. If
you want to create and automate your own custom frequencyoffset measurements (for example, intermodulation distortion),
you may only need Options 014 and 080. For converters that
require input power below -27 dBm, or for devices that have a
large amount of LO feedthrough (like an unfiltered mixer), Option
UNL, which adds source attenuators, is highly recommended.
Besides allowing lower input power levels, these attenuators
improve the isolation between the PNA’s internal source and
LO leakage signals, helping to prevent source-unleveled errors.
For devices that put out signals near or above the receiver’s
compression levels (which varies between –3 and +5 dBm,
depending on the model and frequency), Option 016 is recommended, which adds receiver attenuators. Finally, Option 010,
which adds time-domain analysis, is very useful for gating out
unwanted, time-delayed responses which often occur when
measuring mixers.
Calibration
3 year calibration plans are available at time of instrument
purchase. Contact your local Agilent sales office for details.
Product services
Agilent product services provide tailored assistance related to a
specific need or application. Product services enable you to quickly
learn how Agilent instruments operate, their capabilities, and how
to apply that knowledge to achieve your specific measurement
goals. PNA series services available include:
• Remote scheduled productivity assistance
• 1 Day of start-up assistance
• Daily productivity assistance
• PNA operator training for 8 students at your business site
• PNA operator web classes for 1 student
• Custom services to be qualified by an Agilent technical
consultant
17
Microwave PNA Network Analyzer
Simplified test set block diagrams
Standard power range
Source
Switch/splitter
R1
Reference
receiver
Reference
receiver
A
B
R2
Measurement
receivers
Port 1
Port 2
Extended power range and bias-tees (Option UNL)
Source
Switch
R1
Reference
receiver
Reference
receiver
Source attenuator1
R2
Source attenuator1
Bias-tee
Bias-tee
A
Measurement
receivers
Port 1
1. Source attenuator for E8362/3/4B is 60 dB in 10 dB steps.
Source attenuator for E8361A is 50 dB in 10 dB steps.
18
B
Port 2
Microwave PNA Network Analyzer
Simplified test set block diagrams – continued
Configurable test set (Option 014)
Source
Switch
R1
Reference
receiver
Reference
receiver
A
B
R2
Measurement
receivers
Port 1
Port 2
Configurable test set with extended power range and bias-tees (Option UNL and 014)
Source
Switch
R1
Reference
receiver
Reference
receiver
Source attenuator1
Bias-tee
R2
Source attenuator1
A
B
Bias-tee
Measurement
receivers
Port 1
Port 2
1. Source attenuator for E8362/3/4B is 60 dB in 10 dB steps.
Source attenuator for E8361A is 50 dB in 10 dB steps.
19
Microwave PNA Network Analyzer
Simplified test set block diagrams – continued
Fully optioned, active device or mixer/converter test configuration (Options 014, UNL, 016, 080,
081)
Source
Switch/splitter/leveler
R1
Reference
receiver
Reference
receiver
Source attenuator1
R2
Source attenuator1
Option 081
10 dB steps
Bias-tee
Measurement
receivers
10 dB steps
A
Bias-tee
B
Receiver
attenuator2
Source
out
Rcvr R1
in
SRC
out
Cplr
thru
Cplr
arm
1. Source attenuator for E8362/3/4B is 60 dB in 10 dB steps. Source attenuator for
E8361A is 50 dB in 10 dB steps.
2. Receiver attenuator for E8362/3/4B is 35 dB in 5 dB steps. Receiver attenuator for
E8361A is 50 dB in 10 dB steps.
20
Rcvr A
in
Rcvr B
in
Cplr
arm
Cplr
thru
SRC Rcvr R2 Source
out
in
out
Microwave PNA Network Analyzer
Simplified test set block diagrams – continued
High-power configuration (Option H85)
Source
Switch/splitter/leveler
+30
dBm
+15
R1
dBm
Reference
receiver
Reference
receiver
Source attenuator1
Source attenuator1
+30
dBm
Option 081
+15
dBm
A
+30
dBm
+40
dBm
Rcvr R1
in
SRC
out
Cplr
thru
+30
dBm
Measurement
receivers
10 dB steps
Source
out
+15
R2
dBm
Cplr
arm
+15
dBm
B
Receiver
attenuator2
Rcvr A
in
10 dB steps
+30
dBm
Rcvr B
in
+40
dBm
Cplr
arm
Cplr
thru
SRC Rcvr R2 Source
out
in
out
DUT
preamp
Power levels shown on the diagram are damage levels. At a minimum, keep power levels 6 dB below damage level. For optimal
performance, keep the power level incident upon the receivers -20 dBm or less. This will keep the receivers out of compression.
1. Source attenuator for E8362/3/4B is 60 dB in 10 dB steps. Source attenuator for
E8361A is 50 dB in 10 dB steps.
2. Receiver attenuator for E8362/3/4B is 35 dB in 5 dB steps. Receiver attenuator for
E8361A is 50 dB in 10 dB steps.
21
Microwave PNA Network Analyzer
Simplified test set block diagrams – continued
Fully optioned, pulse-RF, antenna, or mm-wave configuration
(Options 014, UNL, 016, 080, 081, H11)
Aux RF out
(2 to 20 GHz)
Aux LO out
(2 to 20 GHz)
Rear
YIG source
Option 080
Option H11
Multipliers
(1, 2)
Phase-locked loop
8.33 MHz
reference
Offset receiver
Offset
LO
Vtune
Multipliers (1, 2, 4)
LO
Option 081
Option H111
IF gate
Option H111
IF gate
ADC
ADC
External
IF in
R1
R2
Option UNL
External
IF in
Option UNL
External
IF in
External
IF in
ADC
ADC
IF gate
Option H111
A
B
Option UNL
Option UNL
Option 016
Receiver
attenuators
Front
Option 014
Port 1
Option 014
1. Option H11: IF-gate controls and external-IF inputs are accessed on rear panel.
IF gates are enabled with Option H08. External-IF input frequency is 8.33 MHz.
22
IF gate
Option H111
Port 2
Option 014
N5250A Configuration Details
□ N5250A MM PNA system1, 10 MHz to 110 GHz, includes:
E8361A MW PNA with the following options:
• Configurable test set – Option 014
• Extended power range and bias-tees – Option UNL
• Frequency-offset mode – Option 080
• Reference channel switch – Option 081
• IF access – Option H11
N5260A millimeter-wave test set controller with test heads
• 67 to 110 GHz test heads
• 1.0 mm combiner assembly
• Interconnecting cables
• Installation and productivity assistance
Additional options available:
• Millimeter-wave modules with bias-tees N5250A Option 017
• Millimeter-wave modules with bias-tees and
port 2 attenuator - N5250A Option 018
• Receiver attenuator – Option 016
• Time-domain capability – Option 010
• Pulsed-RF measurement capability – Option H082
• Scalar-calibrated converter measurements – Option 0822
• Frequency converter application – Option 0832
Factory integration of the N5250A system integrates the E8361A
with Option H11 and the N5260A millimeter-wave controller with
test heads. On-site installation is included, and the entire system
carries a full one-year, on-site warranty (where available).
Option Descriptions
□ Millimeter-wave modules with bias-tees (N5250A Option 017)
Adds 67 GHz bias-tees to the combiner assembly between the
input to the combiner and the 67 GHz coupler. The bias-tees have
tri-axial connectors for force, sense, and ground. Positioning the
bias-tees close to the DUT greatly improves stability for on-wafer
and in-fixture devices. The bias-tees added for this option have a
voltage rating of 40 volts and a maximum of 0.5 amps.
Banded waveguide solution
In order to assemble a banded waveguide solution, the following
components are needed:
• Microwave PNA network analyzer (E8361A or E8362/3/4B)
with the following options:
• IF access - Option H11
• Configurable test set - Option 014
• Extended power range and bias-tees - Option UNL
• Frequency-offset mode - Option 080
• Reference channel switch - Option 081
• Millimeter-wave test set controller (N5260A)
with no options
• A set of waveguide modules:
• N5260AW15, 50 to 75 GHz
• N5260AW12, 60 to 90 GHz
• N5260AW10, 75 to 110 GHz
• N5260AW08, 90 to 140 GHz
• N5260AW06, 110 to 170 GHz
• N5260AW05, 140 to 220 GHz
• N5260AW03, 220 to 325 GHz
NOTE: To significantly improve system dynamic range above 220 GHz,
Agilent strongly recommends adding two external synthesizers
such as Agilent’s PSG Series signal generators; one for the RF
signal, and one for the LO signal.
For more detailed information, see PNA Millimeter-wave
Technical Overview, literature number 5988-9620EN.
On-wafer applications
For on-wafer applications, Cascade Microtech3 provides complete
probing systems using the N5250A. These include both new
probing systems and upgrades to existing Cascade Microtech
products. Cascade can also provide on-wafer verification and
probing system training. Once the N5250A system is verified
in coax, Cascade Microtech will verify the system through its
wafer probes.
□ Millimeter-wave modules with bias-tees and port 2
attenuator (N5250A Option 018)
Adds 67 GHz bias-tees to the combiner assembly between the
input to the combiner and the 67 GHz coupler. The bias-tees have
tri-axial connectors for force, sense, and ground. Positioning the
bias-tees close to the DUT greatly improves stability for on-wafer
and in-fixture devices. The bias-tees added for this option
have a voltage rating of 40 volts and a maximum of 0.5 amps
Additionally, Option 018 adds a 25 dB micrometer attenuator to
the port 2 test head.
1. For more detailed information regarding the 110 GHz network analyzer system,
refer to the Agilent Web site: www.agilent.com/find/pna and download the
N5250A Technical Overview, literature number 5988-9620EN.
2. Up to 67 GHz.
3. Cascade Microtech is an Agilent Channel Partner.
23
N5250A Millimeter-Wave PNA Block Diagram
E8361A
with Option H11
With Option 017, the signal is routed out of
the PNA from the front panel jumpers rather
than the ports. Without Option 017, the signal
is routed from the front panel ports to the
combiner assembly, allowing access to the
PNA’s internal bias-tees.
Test set I/O
Receiver A
Receiver B
Port 2
Port 1
30 in.
76.2 cm
30 in.
76.2 cm
LO
IF1
RF
IF2
IF3
IF4
48 in.
121.9 cm
48 in.
121.9 cm
Test set controller
N5260A
with
test heads
Optional
bias-tees
(Option 017)
67 to 110 GHz
waveguide head
Test
port 1
Test
port 2
Combiner assembly
67 to 110 GHz
waveguide head
Combiner assembly
SMA
connectors
BNC
connectors
LO: 2 to 20 GHz
R1 R2 A
IF IF IF
B
IF
SMA
connectors
BNC
connectors
RF: 2 to 20 GHz
R1 R2 A B
gate gate gate gate
PNA test set block diagram
To IF multiplexer
(see Figure 5)
Simplified receiver block diagram
To IF multiplexer
(see Figure 5)
LO distribution to
each receiver
IF multiplexer
A/D
RF
LO
(from LO distribution.
See test set
block diagram)
R1
Reference
receiver
Reference
receiver
R2
50 dB
External
IF input
50 dB
IF gating
A
Bias-tee
B
50 dB
50 dB
Bias-tee
Option 016
receiver
attenuators
Port 1
24
Port 2
Measurement Accessories
A complete list of RF and microwave test accessories
is available on our Web site:
www.agilent.com/find/accessories
Accessories are available in these connector types:
50 ohm Type-N, 3.5 mm, 7 mm, 2.4 mm, 2.92 mm, 1.85 mm, 1.0 mm,
and waveguide. Test port cables and a calibration kit should be
added for a complete measurement system. A verification kit is
used to verify corrected system performance.
Cables and adapter sets
Agilent offers cables in the following types:
• single cables in semi-rigid and flexible
• cable sets in semi-rigid and flexible
There are also adapter sets available that protect the test port
and convert the port to the desired connector interface. These
kits contain:
• one male adapter
• one female adapter
To attain the best mechanical rigidity for device connection, use
a single cable and the appropriate special adapter set. To attain
the greatest flexibility for device connection, use a cable set.
Network analyzer
test set
Device
under
test
Network analyzer
test set
Test port
adapter
Coaxial measurements
Mechanical calibration kits include standards, such
as opens, shorts and loads, which are measured by the network
analyzer for increased measurement accuracy.
Electronic calibration (ECal) kits replace mechanical calibration
standards with one solid-state calibration module that is controlled
by the network analyzer via USB, to present many different
impedances to the test ports. A full two-port calibration can be
performed quickly with a single connection. This technique
reduces operator errors and connector wear and abrasion.
Choose a calibration kit for each connector type to be used.
Economy, includes:
• open standards (male and female)
• short standards (male and female)
• fixed-termination standards (male and female)
Standard, includes the devices in the economy kit and adds:
• sliding load standards (male and female) or a series of
offset shorts
Precision, includes the devices in the economy kit and adds:
• 50 ohm airline(s) for TRL calibration
• TRL adapters
Waveguide measurements
Cable set
Single cable
Calibration kits
Device
under
test
For waveguide measurements, Agilent offers mechanical calibration
kits that include:
• waveguide-to-coax adapters (X, P, K, R, Q, U, V)
• precision waveguide section
• flush short circuit
• fixed terminations
• straight section
25
For devices with 1.0 mm connectors
For devices with 1.85 mm connectors
Mechanical calibration/verification kit
Mechanical calibration kits
□ 85059A DC to 110 GHz precision calibration/verification
kit.
Includes:
85059-60003
85059-60007
85059-60004
85059-60008
85059-60002
85059-60006
85059-60001
85059-60005
85059-60009
85059-60010
85059-60019
85059-60020
85059-60021
11920-60001
11920-60002
11920-60003
11500-60001
85059-60016
85059-60017
8710-2079
8710-2156
1.00 mm (m) short 2.450 mm
1.00 mm (f) short 2.450 mm
1.00 mm (m) short 3.000 mm
1.00 mm (f) short 3.000 mm
1.00 mm (m) short 1.825 mm
1.00 mm (f) short 1.825 mm
1.00 mm (m) short 1.300 mm
1.00 mm (f) short 1.300 mm
1.00 mm male open
1.00 mm female open
1.00 mm male load
1.00 mm female load
1.00 mm lossy delay line
1.00 mm (m) to 1.00 mm (m) adapter
1.00 mm (f) to 1.00 mm (f) adapter
1.00 mm (m) to 1.00 mm (f) adapter
1.00 mm (f) to 1.00 mm (f) 8.8 cm cable
1.00 mm mismatch thru adapter
for verification
1.00 mm matched thru adapter
for verification
6 mm, 4 in-lb torque wrench
6 mm open end wrench
Cables
□ 11500I 1.0 mm (f-f) test port cable (8.8 cm)
□ 11500J 1.0 mm (m-f) test port cable (16.0 cm)1
□ 11500K 1.0 mm (m-f) test port cable (20.0 cm)1
□ 11500L 1.0 mm (m-f) test port cable (24.0 cm)1
Adapter set
□ V281C 1.0 mm(f) to V-band waveguide adapter
□ V281D 1.0 mm (m) to V-band waveguide adapter
□ W281C 1.0 mm (f) to W-band waveguide adapter
□ W281D 1.0 mm (m) to W-band waveguide adapter
□ 11920A 1.0 mm (m) to 1.0 mm (m) adapter
□ 11920B 1.0 mm (f) to 1.0 mm (f) adapter
□ 11920C 1.0 mm (m) to 1.0 mm (f) adapter
□ 11921A 1.0 mm (m) to 1.85 mm (m) adapter
□ 11921B 1.0 mm (f) to 1.85 mm (f) adapter
□ 11921C 1.0 mm (m) to 1.85 mm (f) adapter
□ 11921D 1.0 mm (f) to 1.85 mm (m) adapter
□ 11922A 1.0 mm (m) to 2.4 mm (m) adapter
□ 11922B 1.0 mm (f) to 2.4 mm (f) adapter
□ 11922C 1.0 mm (m) to 2.4 mm (f) adapter
□ 11922D 1.0 mm (f) to 2.4 mm (m) adapter
□ 11923A 1.0 mm (f) connector launch assembly
1. For on-wafer applications, two 11500J/K/L cables are required;
one cable for each test port.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard
male connector.
26
□85058B standard: DC to 67 GHz.
Includes:
85058-60101 1.85 mm (m) short 5.4 mm
85058-60102 1.85 mm (m) short 6.3 mm
85058-60103 1.85 mm (m) short 7.12 mm
85058-60104 1.85 mm (m) short 7.6 mm
85058-60105 1.85 mm (f) short 5.4 mm
85058-60106 1.85 mm (f) short 6.3 mm
85058-60107 1.85 mm (f) short 7.12 mm
85058-60108 1.85 mm (f) short 7.6 mm
85058-60109 1.85 mm male open
85058-60110 1.85 mm female open
85058-60111 1.85 mm male load
85058-60112 1.85 mm female load
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
85058-60115 1.85 mm (m) to 1.85 mm (f) adapter
□85058E economy: DC to 67 GHz.
Includes:
85058-60101 1.85 mm (m) short 5.4 mm
85058-60105 1.85 mm (f) short 5.4 mm
85058-60109 1.85 mm male open
85058-60110 1.85 mm female open
85058-60123 1.85 mm male load
85058-60124 1.85 mm female load
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
85058-60115 1.85 mm (m) to 1.85 mm (f) adapter
Electronic calibration kits
□N4694A Microwave ECal: 10 MHz to 67 GHz, 2 ports.
Includes:
Option M0F module with:
N4694-60001 1.85 mm (f) to 1.85 mm (m) ECal module
Option 00M module with:
N4694-60002 1.85 mm (m) to 1.85 mm (m) ECal module
Option 00F module with:
N4694-60003 1.85 mm (f) to 1.85 mm (f) ECal module
Option 00A adds:
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
Cables
□N4697E2 Single, flexible: 1.85 mm (f) to 1.85 mm (f),
96.5 cm, 38 inches
□N4697F2 Set, flexible:
One 1.85 mm (f) to 1.85 mm (f) cable, 62.2 cm,
24.5 inches, p/n N4697-60100
One 1.85 mm (f) to 1.85 mm (m) cable, 62.2 cm,
24.5 inches, p/n N4697-60200
□N4697H2 Single, flexible: 1.85 mm (f) to
1.85 mm (m), 62.2 cm, 24.5 inches
□N4421B-B67 Set of 4, flexible: 1.85 mm (f) to
1.85 mm (m), 91.4 cm, 36 inches
Adapter set
□ 85130H 1.85 mm2 to 1.85 mm
For devices with 2.4 mm connectors
□85133G1 Single, semi-rigid: 2.4 mm (f) to 2.4 mm (m),
Mechanical calibration kits
□85133H1 Single, flexible: 2.4 mm (f) to 2.4 mm (m),
□85056A standard: DC to 50 GHz.
Includes:
00901-60003 2.4 mm (m) fixed broadband load
00902-60004 2.4 mm (f) fixed broadband load
00915-60003 2.4 mm (m) sliding load
00915-60004 2.4 mm (f) sliding load
85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
85056-60020 2.4 mm (m) short
85056-60021 2.4 mm (f) short
85056-60022 2.4 mm (m) open
85056-60023 2.4 mm (f) open
□85056D economy: DC to 50 GHz.
Includes:
00901-60003 2.4 mm (m) fixed broadband load
00902-60004 2.4 mm (f) fixed broadband load
85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
85056-60020 2.4 mm (m) short
85056-60021 2.4 mm (f) short
85056-60022 2.4 mm (m) open
85056-60023 2.4 mm (f) open
Electronic calibration kits
□N4693A Microwave ECal: 10 MHz to 50 GHz, 2 ports.
Includes:
Option M0F module with:
N4693-60001 2.4 mm (f) to 2.4 mm (m) ECal module
Option 00M module with:
N4693-60002 2.4 mm (m) to 2.4 mm (m) ECal module
Option 00F module with:
N4693-60003 2.4 mm (f) to 2.4 mm (f) ECal module
Option 00A adds:
85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
85056-60007 2.4 mm (f) to 2.4 mm (f) adapter
Cables
□85133C1single, semi-rigid: 2.4 mm (f) to PSC-2.4 mm (f),
81 cm, 32 inches
□85133D1set, semi-rigid:
One 2.4 mm (f) to 2.4 mm (m), 53 cm, 21 inches,
p/n 85133-60001
One 2.4 mm (f) to 2.4 mm (f), 53 cm, 21 inches,
p/n 85133-60002
□85133E1single, flexible: 2.4 mm (f) to PSC-2.4 mm (f),
97 cm, 38 inches
□85133F1set, flexible:
One 2.4 mm (f) to 2.4 mm (f), 63 cm, 25 inches,
p/n 85133-60016
One 2.4 mm (f) to 2.4 mm (m), 63 cm, 25 inches,
p/n 85133-60017
53 cm, 21 inches
63 cm, 25 inches
□N4421A-B20 Set of 4, flexible: 2.4 mm (f) to 2.4 mm (m),
91.4 cm, 36 inches
Adapter set
□ 85130G 2.4 mm1 to 2.4 mm
For devices with K connectors (2.92 mm)
Mechanical calibration kits
□ 85056K 2.92/2.4 economy: DC to 40/50 GHz.
Includes:
00901-60003 2.4 mm (m) fixed broadband load
00902-60004 2.4 mm (f) fixed broadband load
00915-60003 2.4 mm (m) sliding load (Option 001)
00915-60004 2.4 mm (f) sliding load (Option 001)
11904-60001 2.4 mm (m) to 2.92 mm (m) adapter
11904-60002 2.4 mm (f) to 2.92 mm (f) adapter
11904-60003 2.4 mm (m) to 2.92 mm (f) adapter
11904-60004 2.4 mm (f) to 2.92 mm (m) adapter
85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
85056-60020 2.4 mm (m) short
85056-60021 2.4 mm (f) short
85056-60022 2.4 mm (m) open
85056-60023 2.4 mm (f) open
Electronic calibration kits
□N4692A Microwave ECal: 10 MHz to 40 GHz, 2 ports.
Includes:
Option M0F module with:
N4692-60001 2.92 mm (f) to 2.92 mm (m) ECal module
Option 00M module with:
N4692-60002 2.92 mm (m) to 2.92 mm (m) ECal module
Option 00F module with:
N4692-60003 2.92 mm (f) to 2.92 mm (f) ECal module
Option 00A adds:
N4692-60021 2.92 mm (m) to 2.92 mm (m) adapter
N4692-60022 2.92 mm (f) to 2.92 mm (f) adapter
Cables
□85133C1single, semi-rigid: 2.4 mm (f) to PSC-2.4 mm (f),
81 cm, 32 inches
□85133D1set, semi-rigid:
One 2.4 mm (f) to 2.4 mm (m), 53 cm, 21 inches,
p/n 85133-60001
One 2.4 mm (f) to 2.4 mm (f), 53 cm, 21 inches,
p/n 85133-60002
□85133E1single, flexible: 2.4 mm (f) to PSC-2.4 mm (f),
97 cm, 38 inches
□85133F1set, flexible:
One 2.4 mm (f) to 2.4 mm (f), 63 cm, 25 inches,
p/n 85133-60016
One 2.4 mm (f) to 2.4 mm (m), 63 cm, 25 inches,
p/n 85133-60017
1. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard male
connector.
27
□85133G1 Single, semi-rigid: 2.4 mm (f) to 2.4 mm (m),
53 cm, 21 inches
□85133H1 Single, flexible: 2.4 mm (f) to 2.4 mm (m),
63 cm, 25 inches
□N4421A-B20 Set of 4, flexible: 2.4 mm (f) to 2.4 mm (m),
91.4 cm, 36 inches
Adapters
□ 11904A 2.4 mm (m) to K (m)
□ 11904B 2.4 mm (f) to K (f)
□ 11904C 2.4 mm (m) to K (f)
□ 11904D 2.4 mm (f) to K (m)
□ 11904S 2.4 mm to K adapter set
Electronic calibration kits
□ 85093C RF ECal: 300 kHz to 9 GHz, 2 ports
Standard module includes
Option M0F with:
85093-60008 3.5 mm (f) to 3.5 mm (m) ECal module
Option 00F module with:
85093-60010 3.5 mm (f) to 3.5 mm (f) ECal module
Option 00M module with:
85093-60009 3.5 mm (m) to 3.5 mm (m) ECal module
Option 00A adds:
85052-60012 3.5 mm (m) to 3.5 mm (m) adapter
85052-60014 3.5 mm (f) to 3.5 mm (f) adapter
85093C-xxx mixed-connector options:
For devices with 3.5 mm or SMA
connectors
Mechanical calibration kits
□ 85052B standard: DC to 26.5 GHz.
Includes:
00902-60003 3.5 mm (m) fixed load
00902-60004 3.5 mm (f) fixed load
00911-60019 3.5 mm (m) sliding load
00911-60020 3.5 mm (f) sliding load
85052-60006 3.5 mm (m) short
85052-60007 3.5 mm (f) short
85052-60008 3.5 mm (m) open
85052-60009 3.5 mm (f) open
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60013 3.5 mm (f) to 3.5 mm (m) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
□ 85052C precision TRL: DC to 26.5 GHz.
Includes:
00902-60003 3.5 mm (m) fixed load
00902-60004 3.5 mm (f) fixed load
85052-60006 3.5 mm (m) short
85052-60007 3.5 mm (f) short
85052-60008 3.5 mm (m) open
85052-60009 3.5 mm (f) open
85052-60032 3.5 mm (f) to 3.5 mm (f) adapter
85052-60033 3.5 mm (m) to 3.5 mm (m) adapter
85052-60034 3.5 mm (f) to 3.5 mm (m) adapter
85052-60035 3.5 mm short TRL line
85052-60036 3.5 mm long TRL line
□ 85052D economy: DC to 26.5 GHz.
Includes:
00902-60003 3.5 mm (m) fixed load
00902-60004 3.5 mm (f) fixed load
85052-60006 3.5 mm (m) short
85052-60007 3.5 mm (f) short
85052-60008 3.5 mm (m) open
85052-60009 3.5 mm (f) open
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60013 3.5 mm (f) to 3.5 mm (m) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
28
Port A option
Type
(f)
(m)
Type
(f)
3.5 mm
102
Type-N
50 ohm
203
101
Port B option
(m)
Type
204
7-16
(f)
(m)
205
206
□ N4431B Microwave ECal: 300 kHz to 13.5 GHz, 4 ports.
Includes:
Option 010 module with:
N4431-60006 4 x 3.5 mm (f) ECal module
N4431B-xxx mixed-connector options:
Connector
type
3.5 mm (f)
3.5 mm (m)
Type-N 50 ohm (f)
Type-N 50 ohm (m)
7-16 (f)
7-16 (m)
Port A
option
101
102
103
104
105
106
Port B
option
201
202
203
204
205
206
Port C
option
301
302
303
304
305
306
Port D
option
401
402
403
404
405
406
□ N4433A Microwave ECal: 300 kHz to 20 GHz, 4 ports.
Includes:
□ Option 010 module with:
N4433-60003 4 x 3.5 mm (f) ECal module
N4433A-xxx mixed-connector options:
Connector
type
3.5 mm (f)
3.5 mm (m)
Port A
option
101
102
Port B
option
201
202
Port C
option
301
302
Port D
option
401
402
□ N4691B Microwave ECal: 300 kHz to 26.5 GHz, 2 ports.
Includes:
Option M0F module with:
N4691-60001 3.5 mm (f) to 3.5 mm (m) ECal module
Option 00M module with:
N4691-60002 3.5 mm (m) to 3.5 mm (m) ECal module
Option 00F module with:
N4691-60003 3.5 mm (f) to 3.5 mm (f) ECal module
Option 00A adds:
85052-60012 3.5 mm (m) to 3.5 mm (m) adapter
85052-60014 3.5 mm (f) to 3.5 mm (f) adapter
Cables
□ 85131C1single, semi-rigid: 3.5 mm (f) to PSC-3.5 mm (f),
81 cm, 32 inches2
□ 85131D1 set, semi-rigid:
One 3.5 mm (f) to 3.5 mm (m), 53 cm, 21 inches,
p/n 85131-60009
One 3.5 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches,
p/n 85131-60010
□ 85131E1 single, flexible: 3.5 mm (f) to PSC-3.5 mm (f),
96.5 cm, 38 inches2
□ 85131F1 set, flexible:
One 3.5 mm (f) to 3.5 mm (m), 62.2 cm, 24.5 inches,
p/n 85131-60012
One 3.5 mm (f) to PSC-3.5 mm (f), 62.2 cm, 24.5 inches,
p/n 85131-60013
□85131G1 single, semi-rigid: 3.5 mm (f) to 3.5 mm (m),
53 cm, 21 inches
□85131H1 single, flexible: 3.5 mm (f) to 3.5 mm (m),
62.2 cm, 24.5 inches
□ 85134C1 single, semi-rigid: PSC-3.5 mm (f) to 2.4 mm (f),
81 cm, 32 inches
□ 85134D1 set, semi-rigid:
One 2.4 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches,
p/n 85134-60002
One 2.4 mm (f) to PSC-3.5 mm (m), 53 cm, 21 inches,
p/n 85134-60001
□ 85134E1 single, flexible: PSC-3.5 mm (f) to 2.4 mm (f),
96 cm, 38 inches
□ 85134F1 set, flexible:
One 2.4 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches,
p/n 85134-60004
One 2.4 mm (f) to PSC-3.5 mm (m), 53 cm, 21 inches,
p/n 85134-60003
□85134G1 single, semi-rigid: 2.4 mm (f) to PSC-3.5 mm (m),
53 cm, 21 inches
□85134H1 single, flexible: 2.4 mm (f) to PSC-3.5 mm (m),
53 cm, 21 inches
□ N4419A-B20 set of 4, flexible: 3.5 mm (m) to 3.5 mm (f),
91.4 cm, 36 inches
□ Z5623A-B20 set of 4, flexible: 3.5 mm (m) to 3.5 mm (m),
91.4 cm, 36 inches (phase-matched)
Adapter sets
□ 85130C 3.5 mm1 to Type-N
□ 85130D 3.5 mm1 to 3.5 mm
□ 85130F 2.4 mm1 to 3.5 mm
1. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard
male connector.
2. For use with E8362A or B.
29
For devices with Type-N connectors
Electronic calibration kits
Mechanical calibration kits
□ N4431B Microwave ECal: 300 kHz to 13.5 GHz, 4 ports.
□ 85054B standard: DC to 18 GHz.
Includes:
00909-60011 Type-N (m) fixed lowband load
00909-60012 Type-N (f) fixed lowband load
85054-60025 Type-N (m) short
85054-60026 Type-N (f) short
85054-60027 Type-N (m) open
85054-60028 Type-N (f) open
85054-60031 Type-N (f) to 7mm adapter
85054-60032 Type-N (m) to 7mm adapter
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter
85054-80010 Type-N (f) sliding load
85054-80009 Type-N (m) sliding load
85054-60050 Type-N (f) connector gage
85054-60052 Type-N (f) gage master
85054-60051 Type-N (m) connector gage
85054-60053 Type-N (m) gage master
□ 85054D economy: DC to 18 GHz.
Includes:
85054-60025 Type-N (m) short
85054-60026 Type-N (f) short
85054-60027 Type-N (m) open
85054-60028 Type-N (f) open
85054-60031 Type-N (f) to 7mm adapter
85054-60032 Type-N (m) to 7mm adapter
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter
85054-60046 Type-N (m) fixed load
85054-60047 Type-N (f) fixed load
Includes:
Option 020 module with:
N4431-60007 4 x Type-N (f) ECal module
N4431B-xxx mixed-connector options:
Connector
type
3.5 mm (f)
3.5 mm (m)
Type-N 50 ohm (f)
Type-N 50 ohm (m)
7-16 (f)1
7-16 (m)1
Port A
option
101
102
103
104
105
106
Port B
option
201
202
203
204
205
206
Port C
option
301
302
303
304
305
306
Port D
option
401
402
403
404
405
406
□ N4432A Microwave ECal: 300 kHz to 18 GHz, 4 ports.
Includes:
Option 020 module with:
N4432-60003 4 x Type-N (f) ECal module
N4432A-xxx mixed-connector options:
Connector
type
3.5 mm (f)
3.5 mm (m)
Type-N 50 ohm (f)
Type-N 50 ohm (m)
Port A
option
101
102
103
104
Port B
option
201
202
203
204
Port C
option
301
302
303
304
Port D
option
401
402
403
404
□ N4690B Microwave ECal: 300 kHz to 18 GHz, 2 ports.
Includes:
Option M0F module with:
N4690-60001 Type-N (f) to Type-N (m) ECal module
Option 00M module with:
N4690-60002 Type-N (m) to Type-N (m) ECal module
Option 00F module with:
N4690-60003 Type-N (f) to Type-N (f) ECal module
Option 00A adds:
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter
Cables 2
Use the test port cables recommended for devices with 7 mm
connectors, and 7 mm to Type-N adapters that are from the
85054B/D Type-N calibration kit (see 7 mm connector section).
1. Limits ECal module high frequency to 7.5 GHz.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard
male connector.
30
For devices with 7 mm connectors
For devices with waveguide
Mechanical calibration kits
Mechanical calibration kits
□ 85050B standard: DC to 18 GHz.
Includes:
00909-60008 7 mm coax termination
85050-60006 7 mm fixed broadband load
85050-80007 7 mm short
85050-80010 7 mm open
85050-80011 7 mm sliding load
□ 85050C precision TRL: DC to 18 GHz.
Includes:
00909-60008 7 mm coax termination
85050-60003 7 mm to 7 mm airline
85050-60005 7 mm to 7 mm TRL adapter
85050-60006 7 mm fixed broadband load
85050-80008 7 mm short
85050-80009 7 mm short collet
85050-80010 7 mm open
□ 85050D economy: DC to 18 GHz.
Includes:
85050-60006 7 mm fixed broadband load
85050-80007 7 mm short
85050-80010 7 mm open
Electronic calibration kits
□ N4696B Microwave ECal: 300 kHz to 18 GHz, 2 ports,
7mm to 7mm Microwave module
X Band
□ X11644A standard, WR-90: 8.2 to 12.4 GHz.
Includes:
00896-60008 X-band standard section
00910-60003 X-band termination
11644-20018 X-band short
11644-20021 X-band shim
□ 85132F cable set (set, flexible 7 mm to 3.5 mm,
62.9 cm each, 24.75 inches each2)
□ 85135F cable set (set, flexible,
7 mm to 2.4 mm, 53 cm each, 21 inches each)
□ X281C adapter (included in calibration kit):
WR-90 to 7 mm
P Band
□ P11644A standard, WR-62: 12.4 to 18 GHz.
Includes:
00896-60007 P-band standard section
00910-60002 P-band termination
11644-20017 P-band short
11644-20020 P-band shim
□ 85132F cable set (set, flexible, 7 mm to 3.5 mm,
62.9 cm each, 24.75 inches each2)
□ 85135F cable set (set, flexible, 7 mm to 2.4 mm,
53 cm each, 21 inches each)
□ P281C adapter (included in calibration kit):
WR-62 to 7 mm
Cables 1
□ 85132C single, semi-rigid: 7 mm to 3.5 mm (f),
81 cm, 32 inches2
□ 85132D set, semi-rigid: two 3.5 mm (f) to 7 mm cables,
53 cm each, 21 inches each2, p/n 85132-60003
□ 85132E single, flexible: 7 mm to 3.5 mm (f),
97.2 cm, 38.25 inches2
□ 85132F set, flexible: two 3.5 mm (f) to 7 mm cables,
62.9 cm each, 24.75 inches each2, p/n 85132-60004
□ 85135C single, semi-rigid: 7 mm to 2.4 mm (f),
81 cm, 32 inches
□ 85135D set, semi-rigid: two 2.4 mm (f) to 7 mm cables,
53 cm each, 21 inches each, p/n 85135-60001
□ 85135E single, flexible: 7 mm to 2.4 mm (f),
96 cm, 38 inches
□ 85135F set, flexible: two 2.4 mm (f) to 7 mm cables,
53 cm each, 21 inches each, p/n 85135-60002
K Band
□ K11644A standard, WR-42: 18 to 26.5 GHz.
Includes:
00896-60006 K-band standard section
00910-60001 K-band termination
11644-20016 K-band short
11644-20019 K-band shim
□ 85134F cable set (set, flexible, 3.5 mm to 2.4 mm,
53 cm each, 21 inches each)
□ K281C adapter (included in calibration kit):
WR-42 to 3.5 mm (f)
Option 012 WR-42 to 3.5 mm (m)
Adapter sets
□ 85130E 2.4 mm1 to 7 mm
1. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard
male connector.
2. For use with E8362A or B.
31
R Band
Verification kits
Includes:
00914-20028 R-band termination
11644-20005 R-band short
11644-20003 R-band shim
11644-60001 R-band 10 cm straight waveguide
11644-60016 R-band 5 cm straight waveguide
□ 85133F cable set (set, flexible, 2.4 mm, 53 cm each,
21 inches each)
□ R281A adapter (2.4 mm (f) to WR-28 waveguide
adapter)
□ R281B adapter (2.4 mm (m) to WR-28 waveguide
adapter)
All Agilent verification kits include:
• precision Z0 airline or match thru
• mismatched airline or mismatch thru
• fixed attenuators
• traceable measured data and uncertainties
□ R11644A standard, WR-28: 26.5 to 40 GHz.
Q Band
□ Q11644A standard, WR-22: 33 to 50 GHz.
Includes:
11644-60005 Q-band termination
11644-20004 Q-band short
11644-20001 Q-band shim
11644-60002 Q-band 10 cm straight waveguide
11644-60017 Q-band 5 cm straight waveguide
□ 85133F cable set (set, flexible, 2.4 mm, 53 cm each,
21 inches each)
□ Q281A adapter (2.4 mm (f) to WR-22 waveguide adapter)
□ Q281B adapter (2.4 mm (m) to WR-22 waveguide adapter)
U Band
□ U11644A standard, WR-19: 40 to 60 GHz.
Includes:
11644-60006 U-band termination
11644-20004 U-band short
11644-20002 U-band shim
11644-60003 U-band 10 cm straight waveguide
11644-60018 U-band 5 cm straight waveguide
V Band
□ V11644A standard, WR-15: 50 to 75 GHz.
Includes:
11644-60025 V-band termination
11644-20015 V-band short
11644-20013 V-band shim
11644-60012 V-band standard section
32
□ 85053B 300 kHz to 26.5 GHz 3.5 mm kit
Includes attenuators, airline and mismatch airline with data on
a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards.
Test procedure is provided in the service manual.
□ 85055A 300 kHz to 18 GHz Type-N kit
Includes attenuators, airline and mismatch airline with data on
a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards.
Test procedure is provided in the service manual.
□ 85057B 45 MHz to 50 GHz 2.4 mm kit
Includes attenuators, airline and mismatch airline with data on
a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards.
Test procedure is provided in the service manual.
□ 85058V 45 MHz to 67 GHz 1.85 mm kit
Includes attenuators, match thru and mismatch thru with data
on a 3.5-inch disk for use in confirming accuracy enhanced
system measurement performance, traceable to national
standards. Test procedure is provided in the service manual.
General Accessories
Amplifiers
USB
□ 83006A power amplifier, 10 MHz to 26.5 GHz, 20 dB gain,
□ N4688A CD-ROM drive
Provides an external read/write CD-ROM drive with a USB cable.
□ N4689A USB hub
Provides a USB hub for connecting additional USB peripherals.
Hard drive
□ N8980A spare hard drive
For use with 500 MHz Pentium III CPU board1
Recommended for use in secure environments.
□ N8981A spare hard drive
For use with 1.1 GHz Pentium M CPU board1
Recommended for use in secure environments.
power out: +18 dBm to 10 GHz or +16 dBm to 20 GHz or
+14 dBm to 26.5 GHz
□ 83017A power amplifier, 50 MHz to 26.5 GHz, 25 dB gain,
power out: +20 dBm to 20 GHz, or +15 dBm to 26.5 GHz
□ 83018A power amplifier, 2 to 26.5 GHz, 27 dB gain to 20 GHz
or 23 dB to 26.5 GHz, power out: +24 dBm to 20 GHz or
+21 dBm to 26.5 GHz
□ 83020A power amplifier, 2 to 26.5 GHz, 30 dB gain to 20 GHz
or 27 dB to 26.5 GHz, power out: +30 dBm to 20 GHz or
+26 dBm to 26.5 GHz
□ 83050A power amplifier, 2 to 50 GHz, 23 dB gain, power out:
+20 dBm to 40 GHz or +17 dBm to 50 GHz
□ 83051A power amplifier, 45 MHz to 50 GHz, 23 dB gain power out:
+12 dBm to 45 GHz or +10 dBm to 50 GHz
Couplers
Probe
□ 85024A high-frequency probe
Provides high-impedance in-circuit test capability from
300 kHz to 3 GHz.
1
Power meters and sensors
Recommended for self support, adjustments and performance
tests to verify proper instrument operation.
□ U2000A USB power sensor, 10 MHz to 18 GHz
□ U2001A USB power sensor, 10 MHz to 6 GHz
□ U2002A USB power sensor, 50 MHz to 24 GHz
□ U2004A USB power sensor, 9 kHz to 6 GHz
□ E4418B single-channel power meter
□ E4419B dual-channel power meter
□ 8481B power sensor, 10 MHz to 18 GHz, Type-N (m), 25 W
□ 8481A power sensor, 10 MHz to 18 GHz, Type-N (m), 100 mW
□ 8485A power sensor, 50 MHz to 26.5 GHz, APC-3.5 mm (m),
100 mW
□ 8487A power sensor, 50 MHz to 50 GHz, 2.4 mm, 300 mW
□ 8487D power sensor, 50 MHz to 50 GHz, 2.4 mm, 100 mW
□ R8486A power sensor, 26 GHz to 40 GHz, waveguide flange
UG-599/U, 100 mW
□ Q8486A power sensor, 33 GHz to 50 GHz, waveguide flange
UG-383/U, 100 mW
□ U8486A power sensor, 50 GHz to 75 GHz, waveguide flange
UG-385/U, 200 mW avg
□ E4412A CW power sensor, 10 MHz to 18 GHz, Type-N (m), 200 mW
□ E4413A CW power sensor, 50 MHz to 26.5 GHz, 3.5 mm, 200 mW
□ 87300B coaxial coupler, 1 to 20 GHz, SMA (f), 10 dB coupling
□ 87300C coaxial coupler, 1 to 26.5 GHz, 3.5 mm (f), 10 dB coupling
□ 87301B coaxial coupler, 10 to 46 GHz, 2.92 mm (f), 10 dB coupling
□ 87301D coaxial coupler, 1 to 40 GHz, 2.4 mm (f) or optional
2.92 mm (f), 13 dB coupling
□ 87301E coaxial coupler, 2 to 50 GHz, 2.4 mm (f), 10 dB coupling
□ 87310B 90 o coaxial coupler, 1 to 18 GHz, SMA (f), 3 dB coupling
Equipment rack accessories
□ E3663AC Rail kit
□ 5063-9217 Rack mount kit, for use without handles
(included with Option 1CM)
□ 5063-9205 Front handle kit3
□ 5063-9224 Rack mount kit with handles3
□ 5063-9237 Rack mount kit, for use with standard supplied
handles (included with Option 1CP)3
1. The 500 MHz CPU board has one USB port oriented vertically and a
single GPIB port. The 1.1 GHz CPU board has four USB ports and two
GPIB ports. For more information on this subject, refer to
na.tm.agilent.com/pna/hdnumbers.html.
2. For the latest guide to power meters and power sensors, refer to the
Agilent web site: www.agilent.com/find/powermeters
3. Front handles and Option 1CP (rack mount with handles) are not a
vailable for the N5242A.
33
Applications
Material measurements
□ 85070E High-Temperature Dielectric Probe Kit
The 85070E enables measurements of the dielectric properties
of materials quickly and conveniently. Measurements made
with this probe are nondestructive and require no sample
preparation. The dielectric probe is well suited for measurements
of liquid, semisolid and flat solid materials. Measurement
results can be viewed in a variety of formats (ε’r, ε”r, tan δ
or Cole-Cole). The supplied software can be run in the PNA
analyzer or on a PC.
□ 85071E Materials Measurement Software
The 85071E materials measurement software calculates the
permittivity and permeability of material samples placed in a
coaxial airline or a rectangular waveguide. The measurement
technique works well for solid materials that can be machined
to fit precisely inside a transmission line. Measurement
results can be viewed in a variety of formats (ε’r, εr, µ’r, µ”r, tan δ,
or Cole-Cole µ). The software can be run in the PNA analyzer
or on a PC.
1
Pulsed measurements
The pulsed RF measurement capability (Option H08) and IF access
(Option H11), are recommended for pulsed measurements with
the PNA Series.
Pulse/pattern generators
Recommended to provide pulse signals and timing to the pulsed
S-parameter text set and MW PNA
□ 81104A Pulse/pattern generator, 80 MHz, single-/dual-channel
with one or two Agilent 81105A output modules.
□ 81110A Pulse/pattern generator, 165 MHz, single-/dual-channel
with one or two Agilent 81111A output modules.
Note: Each pulse/pattern generator must be ordered with its
associated output modules depending on the measurement
configuration.
Pulsed S-Parameter test sets
□ Z5623AH81 Pulsed S-parameter test set, 2 to 20 GHz
Includes a pin-diode switch to modulate the analyzer’s
internal source, an amplifier, and directional coupler
to provide a pulsed reference to the analyzer.
□ Z5623AH83 Pulsed S-parameter test set, 2 to 20 GHz
Includes two pin switches for bi-directional (forward and
reverse) pulsed-RF stimulus, and two directional couplers for
the reference channels. It does not include internal amplifiers,
but has front panel access loops for switching in external
amplifiers to boost port power in both directions.
1. For more details regarding pulsed measurement configurations with the
PNA Series, refer to Agilent’s Web site (www.agilent.com/find/pna)
to download a copy of the Microwave PNA Series Network Analyzer
Configuration Guide for Pulsed Measurements, literature number 5988-9833EN.
34
□ Z5623AH84 Pulsed S-parameter test set, 2 to 40 GHz
Includes two pin switches for bi-directional (forward and
reverse) pulsed-RF stimulus, and two directional couplers for
the reference channels. It does not include internal amplifiers,
but has front panel access loops for switching in external
amplifiers to boost port power in both directions.
□ Z5623AH86 Pulsed S-parameter test set, 2 to 40 GHz
Includes one pin switch to modulate the analyzer’s
internal source in the forward direction, and one directional
coupler for the reference channel. It does not include internal
amplifiers, but has front panel access loops for switching in
an external amplifier to boost port power.
□ Z5623AH87 Pulsed S-parameter test set, 1 to 50 GHz
Includes two pin switches for bi-directional (forward and
reverse) pulsed-RF stimulus. It does not include internal amplifiers,
but has front panel access loops for switching in external
amplifiers to boost port power in both directions.
□ Z5623AH89 Pulsed S-parameter test set, 10 MHz to 5 GHz
Includes one pin switch to modulate the analyzer’s
internal source in the forward direction. This test set has no
internal amplifier, no reference channel variable attenuator, and
no GPIB control (manual control only).
□ Z5623AH90 Pulsed S-parameter test set, 1 to 50 GHz
Same as Z5623AH87, but adds 50 GHz couplers to the front
panel to allow DUT connection on the test set instead of
using the PNA test ports.
Note: Pulse biasing can be achieved with or without the use
of a pulsed S-parameter test set. A proper pulse-bias driver
must be used. Contact your local Agilent Sales Representative
for additional pulsed S-parameter test set configurations and
details.
Peripherals
The following peripherals may be used with the Microwave PNA
Series. Other peripherals not listed here may also be compatible
with these instruments.
Monitors
VGA-compatible monitor
Printers
USB, LAN, parallel or serial printers with Microsoft® Windows®
printer driver
Interface cables
Choose the appropriate cables to connect each
peripheral to the network analyzer.
□ 10833A GPIB cable, 1.0 m (3.3 ft)
□ 10833B GPIB cable, 2.0 m (6.6 ft)
□ 10833D GPIB cable, 0.5 m (1.6 ft)
□ 82357B GPIB to USB interface
Upgrade Kits
Upgrade kits for the PNA Series
E8362B, E8363B, E8364B, E8361A, N5250A3
Upgrade kits are available to add options after initial purchase. To
order an upgrade kit for the PNA series, order the analyzer’s model
number followed by a “U”, then indicate the option to be added (for
example, E8362BU-010). The serial number of the instrument to be
retrofitted is required as part of the order.
□ Time-domain (Option 010)
□ 4-Port measurement application (Option 550)
User installable.
□ Configurable test set (Option 014)
Provides six front-panel RF access loops.
Includes installation at an Agilent service center.
□ Receiver attenuators (Option 016)
Includes installation at an Agilent service center.
□ Extended memory (Option 022)
Applies only to E8362B/63B/64B/61A with 256 MB of RAM.
Includes installation at an Agilent service center.
□ Frequency range upgrade to an E8363B (40 GHz) PNA
(Option 040/041)
Available only for the E8362A/B. Includes
installation at an Agilent service center.
□ Frequency range upgrade to an E8364B (50 GHz) PNA
(Option 050/051)
Available only for the E8362A/B and E8363A/B.
Includes installation at an Agilent service center.
□ Frequency range upgrade to an E8361A (67 GHz) PNA
(Option 067/068))
Available only for the E8363B and E8364B.
Includes installation at an Agilent service center.
□ Frequency-offset (Option 080)
Includes installation at an Agilent service center.
□ External reference switch (Option 081)
Includes installation at an Agilent service center.
□ Scalar-calibrated converter measurements (Option 082)
User installable. Option 080 required.
□ Frequency converter measurement application (Option 083)
User installable. Option 080 and 081 required.
□ Embedded LO Measurements (Option 084)
Advanced software tuning that provides absolute group delay of
converters with embedded LOs without the need for access to a
common reference signal. The measurement result is the same
as locking the DUT LO to the reference mixer LO. (Options 080
and 083 required) Requires firmware A.07.05 and above plus
1.1 GHz CPU board.
Enables full 4-port error correction and differential
measurements. Option 014 and external test set required.
User installable.
□ N-port capabilities (Option 551)
Adds full N-port error correction and measurement
capabilities. Option 014 and external test set required.
User installable.
□ Extended power range (Option UNL)
Adds a step attenuator and a bias-tee between source and
each test port. Includes installation at an Agilent service center.
□ Pulsed-RF measurement capability (Option H08)
Provides software to set up and control pulsed-RF
measurements using narrowband detection, with point-in-pulse
and pulse-profile capability. User installable.
□ IF access (Option H11)
Provides hardware for antenna, point-in-pulse, and millimeterwave measurements. Adds rear-panel RF and LO outputs,
external IF inputs, and IF gates (gates enabled with Option H08).
Includes installation at an Agilent service center.
□ High-power test set (Option H85)1
Removes bias tees for higher test port power-handling capability.
Options UNL, 014, 016, 080, and 081 are required. Includes
installation at an Agilent Service Center.
□ Upgrade to C model2 (Option 221 or Option 241)
Provides new front panel, new hard drive with latest firmware and
new GUI. Option 221 is available for the E8361A, E8362/3/4B,
and N5230A 2-port instruments. Option 241 is available for
N5230A 4-port instruments.
1. Please contact Agilent for ordering this upgrade.
2. Some older PNAs may also require the purchase of a new CPU board.
3. For N5250A upgrades, order E8361AU options.
35
Upgrade kits for the PNA-L Series
N5230A
Upgrade kits are available to add options after initial purchase. To
order an upgrade kit for the PNA-L series, order the analyzer’s
model number followed by a “U”, then indicate the option to be
added (example: N5230AU-010). The serial number of the instrument
to be retrofitted is required as part of the order.
□ Time-domain upgrade kit (Option 010)
□ 20 GHz 4-port configurable test set, extended power range &
The serial number of the instrument to be retrofitted must be
specified when ordering this kit. User installable.
□ Frequency-offset upgrade kit (Option 080)
The serial number of the instrument to be retrofitted must be
specified when ordering this kit. User installable.
□ Scalar-calibrated converter measurements (Option 082)
User installable. Option 080 required.
□ 4-port measurement application (Option 550)
Enables full 4-port error correction and differential measurements
on a 2-port network analyzer with configurable test set (Option x25).
External test set required. User installable.
□ N-port capabilities (Option 551)
Adds full N-port error correction and measurement capabilities to
PNA-L with configurable test set (Option xx5 or x46). External test
set required. User installable.
□ 6 or 13.5 GHz configurable test set & extended power range
upgrade kit (Option 901)
Applicable to 6 or 13.5 GHz PNA-L (N52300-020, N52300-120). Upgrade
to configurable test set and extended power range. Includes
installation at an Agilent service center.
□ 20 GHz 2-port configurable test set & extended power range
upgrade kit (Option 921)
Applicable to 20 GHz PNA-L (N52300-220 with serial prefix
MY4500A and below). Upgrade to configurable test set and
extended power range. Includes installation at an Agilent service
center.
□ 20 GHz 2-port configurable test set & extended power range
upgrade kit (Option 922)
Applicable to 20 GHz PNA-L (N52300-220 with serial prefix
MY4640A and above). Upgrade to configurable test set and
extended power range. Includes installation at an Agilent
service center.
□ 13.5 or 20 GHz 4-port configurable test set & extended power
range upgrade kit (Option 926)
Applicable to 20 GHz 4-port PNA-L (N52300-140, N52300-240).
Upgrade to configurable test set and extended power range.
Includes installation at an Agilent service center.
□ 13.5 GHz 4-port configurable test set, extended power range &
internal second source upgrade kit (Option 928)
Applicable to 13.5 GHz 4-port PNA-L (N52300-145). Upgrade to
configurable test set, extended power range and internal second
source. Includes installation at an Agilent service center.
(Option 080 recommended. Please note, Option 080 is needed
in order to have independent control of the two internal sources.)
internal second source upgrade kit (Option 927)
Applicable to 20 GHz 4-port PNA-L (N52300-245). Upgrade to
configurable test set, extended power range and internal second
source. Includes installation at an Agilent service center.
Option 080 recommended.
□ 40 or 50 GHz configurable test set & extended power range
upgrade kit (Option 941)
Applicable to 40 or 50 GHz PNA-L (N52300-420, N52300-520).
Upgrade to configurable test set and extended power range.
Includes installation at an Agilent service center.
□ Frequency range upgrade from 6 to 13.5 GHz (Option 960)
Applicable to the 6 GHz PNA-L (N52300-020, N52300-025).
Includes installation at an Agilent service center.
□ Frequency range upgrade from 13.5 to 20 GHz (Option 966)
Applicable to the 13.5 GHz 4-port PNA-L (N52300-140,
N52300-145, N52300-146). Includes installation at an Agilent
service center.
□ Frequency range upgrade from 20 to 40 GHz (Option 971)
Applicable to the 20 GHz PNA-L (N52300-220). Includes
installation at an Agilent service center.
□ Frequency range upgrade from 20 to 40 GHz (Option 973)
Applicable to the 20 GHz PNA-L (N52300-225 with serial
prefix MY4500A and below). Includes installation at an
Agilent service center.
□ Frequency range upgrade from 40 to 50 GHz (Option 990)
Applicable to the 40 GHz PNA-L (N52300-420, N52300-425).
Includes installation at an Agilent service center.
For additional upgrade paths, contact your Agilent field office.
x20
020
6 GHz
x25
960
9 01
13.5 GHz
x46
140 926
125
145
92 8
966
146
966
220 921/9
240 926
22
20 GHz
225
971
420
941
990
50 GHz
966
245 927
246
973
40 GHz
520 941
425
990
525
PNA-L upgrade path examples.
36
x45
025
960
120
x40
901
Upgrade kits for the PNA-X N5242A
Upgrade kits are available to add options after initial purchase.
To order an upgrade kit for the PNA-X, order the analyzer’s model
number followed by a “U”, then indicate the option to be added
(example: N5242AU-010). The model and serial numbers of the
instrument to be retrofitted are required as part of the order.
□ Pulse measurements (Option H08)
□ 2 ports, add an internal 2nd source, a combiner & mechanical
User installable.
□ Time-domain (Option 010)
User installable.
□ Add IF inputs for antenna and millimeter-wave (Option 020)
User installable.
□ Add pulse modulator to internal 1st source (Option 021)
User installable.
□ Add pulse modulator to internal 2nd source (Option 022)
User installable. Option 224 or 400 required.
□ Add four internal pulse generators (Option 025)
User installable.
□ Frequency offset (Option 080)
User installable.
□ Scalar-calibrated converter measurements (Option 082)
User installable. Option 080 required, and can not be ordered
with Option 083.
□ Frequency converter measurements (Option 083)
User installable. Option 080 required, and can not be ordered
with Option 082.
□ Embedded LO measurements (Option 084)
User installable. Options 080 and 083 required. Requires
firmware A.07.50 and above.
□ Gain compression application (Option 086)
User installable. Requires firmware A.08.00 and above.
□ N-port capabilities (Option 551)
User installable.
□ Perpetual license for built-in performance test software for
Agilent inclusive calibration (Option 897)
User installable. Additional hardware required.
□ Perpetual license for built-in performance test software for
standards compliant calibration (Option 898)
User installable. Additional hardware required.
□ 2 ports, extended power range and bias-tees (Option 921)
Applicable to 2-port model only (N5242A-200). This upgrade
adds one 65 dB source attenuator, one 35 dB receiver attenuator,
and one bias-tee to each test port. Includes installation at an
Agilent service center. Option 200 required.
switches (Option 922)
Applicable to 2-port models only (N5242A-200, N5242A-219).
This upgrade adds an internal second source, a combiner and
mechanical switches. Access to the second source is available
through two output (SMA) connectors on the front panel.
Includes installation at an Agilent service center. Options 200,
219 and 080 required.
□ Fully corrected noise figure measurements, 2-port
(Option 924)
Adds fully-corrected noise figure measurements to 2-port
analyzer. Includes installation at an Agilent Service Center.
Option 219 or 224 required.
□ 4 ports, extended power range and bias-tees (Option 926)
Applicable to 4-port model only (N5242A-400). This upgrade
adds one 65 dB source attenuator, one 35 dB receiver attenuator,
and one bias-tee to each test port. Includes installation at an
Agilent service center. Option 400 required.
□ 4 ports, add an internal combiner & mechanical switches
(Option 927)
Applicable to 4-port models only (N5242A-400, N5242A-419).
This upgrade adds a combiner and mechanical switches.
Includes installation at an Agilent service center. Options 400,
419 and 080 required.
□ Fully corrected noise figure measurements, 4-port
(Option 929)
Adds fully-corrected noise figure measurements to 4-port
analyzer. Includes installation at an Agilent Service Center.
Option 419 or 423 required.
N5242A PNA-X upgrade path
2-port
219
200
200
921
219
224
922
224
4-port
419
400
400
926
419
423
927
423
37
www.agilent.com
Remove all doubt
Your equipment restored to like new performance, returned on time
For more information on Agilent Technologies’ products,
applications or services, please contact your local Agilent office. The complete list is available at:
www.agilent.com/find/contactus
www.agilent.com/find/emailupdates
Get the latest information on the products and applications
you select.
Americas
Canada
Latin America
United States
(877) 894-4414
305 269 7500
(800) 829-4444
www.agilent.com/find/quick
Quickly choose and use your test equipment solutions with
confidence.
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Thailand
1 800 629 485
800 810 0189
800 938 693
1 800 112 929
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
1 800 226 008
Europe & Middle East
Austria
Belgium
Denmark
Finland
France
0820 87 44 11
32 (0) 2 404 93 40
45 70 13 15 15
358 (0) 10 855 2100
0825 010 700*
Key Web Resources
Visit our Web sites for additional product information and literature:
www.agilent.com/find/pna
Electronic calibration (ECal) visit:
www.agilent.com/find/ecal
Material test equipment:
www.agilent.com/find/materials
Test and measurement accessories:
www.agilent.com/find/accessories
Antenna and radar cross-section products visit:
www.agilent.com/find/antenna
Multiport test sets visit:
www.agilent.com/find/multiport
*0.125 €/minute
Pulsed-RF products visit:
www.agilent.com/find/pulsedRF
Germany
On-wafer and in-fixture measuring products visit:
www.agilent.com/find/probingRF
Ireland
1890 924 204
Israel
972-3-9288-504/544
Italy
39 02 92 60 8484
Netherlands
31 (0) 20 547 2111
Spain
34 (91) 631 3300
Sweden
0200-88 22 55
Switzerland
0800 80 53 53
United Kingdom
44 (0) 118 9276201
Other European Countries:
www.agilent.com/find/contactus
Agilent’s service and support products visit:
www.agilent.com/find/tm_services
Expand your measurement capabilities with
Agilent qualified channel partners
Our channel partners offer accessories and
measurement solutions that extend your network
analysis capabilities.
For more information about probing equipment and
accessories, contact:
Cascade Microtech, Inc
2430 NW 206th Avenue
Beaverton, Oregon 97006, USA
Toll free telephone: 1-800-550-3279
Telephone: (503) 601-1000
Fax: (503) 601-1002
Web site: www.cascademicrotech.com
E-mail: [email protected]
Pentium® is a U.S. registered trademark of Intel Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
01805 24 6333**
**0.14 €/minute
Revised: March 27, 2008
Product specifications and descriptions in this document
subject to change without notice.
© Agilent Technologies, Inc. 2007, 2008
Printed in USA, June 9, 2008
5988-7989EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement