TM
#300-29X CHLORINE/BROMINE FEEDER
For commercial-size applications
Features:
• No special venting required.
• Completely enclosed-no escaping gases.
• Positive external no-clog chlorine control valve.
• No equipment damage.
Feeds sanitizer directly to pool or spa.
• All parts replaceable.
YOUR LIFEGARD ® FEEDER IS THE MOST EFFICIENT AND TROUBLE-FREE AUTOMATIC FEEDER YOU CAN BUY,
BUT IT CAN ALSO BE DANGEROUS TO YOU AND YOUR EQUIPMENT. PLEASE FOLLOW INSTRUCTIONS EXACTLY AND
HEED ALL CAUTIONS. YOUR SAFETY AND THE PROTECTION OF YOUR EQUIPMENT IS OUR FIRST CONCERN.
WHERE TO INSTALL YOUR FEEDER
IF YOUR POOL OR SPA HAS COPPER PLUMBING . . . STOP!!
Never install the feeder into copper plumbing as pipe damage could occur. Feeder should be installed ABOVE POOL WATER LEVEL whenever practical. If installed below water level these special instructions must be followed for safe and proper operation. When the feeder is installed below water level, two conditions must be overcome.
1. ISOLATION OF THE FEEDER FROM POOL WATER: The control valve when shut off to “off” isolates it on the side. A one way check valve such as the Rainbow R172324NS or other chemically resistant check valve will have to be attached on the discharge line at the top of the feeder.
NOTE: Never use any type of isolation valve on the discharge or outlet side of the feeder.
Damage to the feeder will occur due to pressure build up. Use only a one-way corrosion resistance check valve. If isolation valves are used, remember to open them as soon as possible following recharging. Never leave closed for long periods of time as pressure will build up. Isolation is necessary to accomplish “DRAINING” in condition #2 which follows.
2. DRAINING: To prevent dangerous splash back of highly chlorinated water during recharging, the feeder will have to be emptied. There is a ½" MPT plug on side of feeder
(see drawing) that can be removed for draining. To facilitate draining: A drain valve is available from your dealer. Details on back drawing.
The outlet line must be installed after the heater. If your pool does not have a heater, then it must be installed after the filter. DAMAGE TO YOUR HEATER COULD RESULT IF
HIGHLY CHLORINATED WATER FLOWS THROUGH IT. REFER TO INSTALLATION
DRAWING FIGURE A
Install the inlet line between the pump and filter. Detailed installation instructions follow in the next section.
IMPORTANT PLUMBING HINTS
All male pipe fittings must be wrapped with 3-4 turns of teflon tape to act as a thread sealant. Always wrap counter-clockwise (opposite of direction to tighten) Never overtighten fittings, they are plastic and can be broken. Usually 2-3 turns past finger tight will prevent any leaks. A fitting can always be tightened more if it leaks but not once it is broken. Additional saddle clamps (Part No. R172264) may be required if plumbing is over
2" in diameter. Clamps can be interlocked. For plumbing 3" to 6" diameter, order saddle clamps (Part No. R172264XL). It is recommended that the Feeder be bolted down.)
1. Position feeder close to the filter and cut tubing to desired length. Be careful to cut tubing ends straight.
2. ATTACH INLET LINE TO FEEDER. Wrap ½" x short nipple with teflon tape. Screw nipple into bottom ½" FPT hole in side of feeder. Screw control valve onto other end of nipple. Be careful not to overtighten. Wrap 90 degree tube fitting with teflon tape and screw into valve. Push compression nut over tubing end of elbow. Push tubing onto tapered end of elbow. Tighten nut firmly by hand.
SEE DRAWING ON OTHER SIDE OF INSTRUCTION SHEET.
3. ATTACH OUTLET LINE TO FEEDER. Wrap 90 degree fitting with teflon tape and screw into top ½" FPT hole on side of feeder. Push compression nut over tubing end, then push tubing onto tapered end of elbow. Tighten nut firmly by hand.
4. INSTALL INLET LINE IN PLUMBING. (Line to bottom side of feeder). Turn off pump and timer switches. Drill 9 /
16
" hole in plumbing, remove burrs and install saddle clamp assembly.
Secure tubing to saddle clamp fitting by tightening clamp. Make sure clamp is below rib at end of saddle fitting. SEE DRAWING FIGURE A.
5. INSTALL OUTLET LINE IN PLUMBING. (Line from top of feeder.) Drill 9 /
16
" hole in plumbing AFTER the heater and remove burrs. SEE DRAWING FIGURE A. Install saddle clamp assembly. Attach tubing as in #4 above. Installation is now complete.
SEE INSTALLATION DRAWING FIGURE A ON OTHER SIDE.
DIRECTIONS FOR USE
Before start up of feeder, your pool should be properly conditioned and the chlorine residual should be 1.0 to 1.5 ppm, (Bromine 2.0-4.0 ppm). The sanitizer demand in a pool varies and is dependent upon many factors; sunlight, bather load, water temperature, etc. As a result, the valve setting may have to be changed from time to time to conform to conditions.
For example, the winter setting may be 2 and the summer setting may be 3.
Recommended start setting #3. Check residual daily to find ideal valve setting. Note:
Higher numbers dispense more sanitizer.
START UP INSTRUCTIONS
Exercise extreme caution when opening or servicing feeder. Do not inhale fumes. Wear protective gear. Follow manufacturer's suggestions for handling the chemical.
1. If below water level, close the control valve and drain any water in feeder by removing
¼" NPT plug in bottom, or by opening valve on optional drain kit. After draining, reinstall plug (use teflon tape) or close drain valve.
2. Remove cap of feeder and fill with Trichlor or bromine tablets. For maximum dispensal rate use 1" diameter tablets, 3" tablets produce less than 40% of 1" tablets.
3. Making sure O-Ring is clean, lubricated with Lifegard Silicone and is in place, replace cap. Hand tighten only.
4. Turn on pump and timer switches. Open control valve to #5 for one minute; which will allow feeder to fill with water. Adjust control valve according to your pool's size. Larger numbers dispense more sanitizer. The water in a newly filled pool should be properly conditioned to ensure maximum effectiveness of the Lifegard Automatic Feeder. Consult your local pool dealer for water conditioning information in your area. Refer to tablet container for recommended residual. It is recommended that the sanitizer level be checked daily for the first 5 days. Remember that on hot days higher water temperature or increased pool activity will cause your pool to use more sanitizer. When possible, increase the feed a day or two in advance.
HOW TO RECHARGE
1. SHUT OFF PUMP AND TIMER SWITCHES. OPEN CONTROL VALVE TO #5
(If below water, level, see special instructions below.)
2. Remove cap; this will allow water and fumes to drain from feeder.
3. Fill with PROPER SIZE TABLETS (SEE START UP INSTRUCTIONS #2)
4. Making sure O-Ring is clean, lubricated with Lifegard Silicone and is in place, replace cap. Hand tighten only.
5. Turn on pump and timer switches.
6. Leave control valve on #5 for one minute, this will allow feeder to fill with water. Reset control valve to original setting. Inspect inlet and outlet lines each time feeder is recharged.
Replace lines yearly if necessary. Model 300-29X may require drain kit part #R172268 and a corrosion resistant check valve part #R172324. (See illustration)
BELOW WATER LEVEL RECHARGING INSTRUCTIONS
1. Shut off pump and timer switches.
2. Shut off control valve.
3. Place a clean container under drain and open drain valve.
4. Exercise extreme caution when opening or servicing feeder. Do not inhale fumes.
Wear protective gear. Remove cap. water will now drain from feeder. Empty container back into pool or spa.
5. Close drain valve. Follow chemical manufacturer's recommendations for handling chemical used in your feeder. Fill with proper size tablets or sticks.
6. Making sure O-Ring is clean, lubricated with Lifegard Silicone and is in place, replace cap. Hand tighten only.
7. Turn on pump and timer switches.
8. Reset control valve to original setting. Inspect inlet and outlet lines each time feeder is recharged. Replace lines yearly if needed.
D A N G E R
READ CAREFULLY
This feeder is designed to use only CLEAN Trichlor-s-trizinetrione OR CLEAN Bromine tables - slow dissolving type. Never use dirty tablets. UNDER NO
CIRCUMSTANCES MIX Trichlor or Bromine with Calcium Hypochlorite, with other forms of concentrated chlorine or with other chemicals. Keep inside of feeder clean of dirt and debris at all times. FIRE AND/OR EXPLOSION MAY RESULT.
NEVER use oils or grease to lubricate o-ring. Oil in contact with Trichlor OR Bromine may result in FIRE. Lubricate o-ring with Lifegard Silicone o-ring Lubricant
ONLY, available at your dealers. If shock treatments or Algaecides containing chemicals other than sanitizers tablets in feeder must be used, turn off Feeder OR remove tablets until the shock or Algae treatment is complete and all granules have dissolved. Failure to do so may result in granules mixing in feeder causing
FIRE AND/OR EXPLOSION. The shock or algae treatment dissolved in water is safe with tablets. If you are not the original owner of this feeder, not sure which chemicals was used, or if dirt and/or debris inside feeder, be SAFE and flush thoroughly with fresh water. CAUTION SHOULD BE USED WHEN REMOVING
CAP. DO NOT INHALE FUMES.
CALCIUM HYPOCHLORITE IS NOT TO BE USED IN ANY FORM.
