UG_TV-IP110_110W(v1.0.1)

UG_TV-IP110_110W(v1.0.1)
P REFACE
Thank you for purchasing the TV-IP110/TV-IP110W Wire/Wireless
Internet Camera Server, a powerful and high-quality image network camera.
The camera can be installed as a standalone system within your application
environment easily and quickly, and supports remote management function
so that you can access and control it using a Web browser on your PC.
This guide will provide you more information of instruction and
illustrations on how to use your camera, which includes:
Chapter 1
Introduction to Your Camera describes the features of the
camera. You will also know the components and functions of
the camera.
Chapter 2
Hardware Installation helps you install the camera according
to your application environment. You can use this camera at
home, at work, at any where you want.
Chapter 3
Accessing the Camera lets you start using your camera
without problem. The camera can be set up easily and work
within your network environment instantly.
Chapter 4
Configuring the Camera guides you through the
configuration of the camera using the web browser on your PC.
Chapter 5
Using SecurView™ shows you the detail instructions on
operating SecurView™ software.
Chapter 6
Appendix provides the specification of the camera and some
useful information for using your camera.
NOTE The illustrations and configuration values in this guide are for
reference only. The actual settings depend on your practical
application of the camera.
Contents
PREFACE ......................................................................... 1
CHAPTER 1 ..................................................................... 4
INTRODUCTION TO YOUR CAMERA ............... 4
1.1 CHECKING THE PACKAGE CONTENTS ...................................4
TV-IP110 (FRONT/BACK VIEW) ....................................................5
TV-IP110W (FRONT/BACK VIEW) .................................................6
1.3 FEATURES AND BENEFITS .....................................................8
1.4 SYSTEM REQUIREMENT .........................................................9
CHAPTER 2 ................................................................... 10
HARDWARE INSTALLATION .............................. 10
2.1
2.2
2.3
INSTALLING THE CAMERA STAND .......................................10
CONNECTING THE CAMERA TO LAN...................................11
APPLICATIONS OF THE CAMERA ..........................................12
CHAPTER 3 ................................................................... 13
ACCESSING THE CAMERA .................................. 13
3.1
3.2
3.3
USING IP SETUP ..................................................................13
ACCESSING TO THE CAMERA...............................................18
CONFIGURING THE IP ADDRESS OF THE PC ........................21
CHAPTER 4 ................................................................... 22
CONFIGURING THE CAME RA ........................... 22
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
USING THE WEB CONFIGURATION ......................................22
USING SMART WIZARD .......................................................23
BASIC SETUP .......................................................................27
NETWORK SETTINGS ...........................................................31
SETTING UP VIDEO ..............................................................38
EVENT SERVER CONFIGURATION ........................................41
MOTION DETECT .................................................................45
EVENT CONFIG ....................................................................47
TOOLS .................................................................................52
INFORMATION .....................................................................54
CHAPTER 5 ................................................................... 55
SECURVIEW™ SOFTWARE .................................. 55
5.1 INSTALLATION ...............................................................55
5.2 USING INSTALLATION ..................................................60
ITEM FEATURES ............................................................................60
TO REMOVE A CAMERA ................................................................70
TO LINK TO THE WEB PAGE OF THE CAMERA ...............................70
TO RECORD VIDEO ........................................................................71
TO CONFIGURE THE RECORDING SETTINGS ...................................77
TO PLAYBACK THE RECORDED VIDEO ..........................................78
TO SET UP MOTION DETECTION OPTIONS ......................................79
ACCOUNT .....................................................................................81
OTHER ..........................................................................................81
INFORMATION...............................................................................82
CHAPTER 6 ................................................................... 83
APPENDIX ..................................................................... 83
A.1 SPECIFICATION ....................................................................83
C HAPTER 1
I NTRODUCTION TO Y OUR
C AMERA
1.1 Checking the Package Contents
Check the items contained in the package carefully. You should have the
following:







TV-IP110/TV-IP110W Network Camera.
Multi-Language Quick Installation Guide
Utility CD-ROM
Detachable External Antenna (for TV-IP110W only)
Camera Stand
RJ-45 Ethernet Cable
AC Power Adapter (5VDC, 2.5A)
NOTE: If there is any item damage or missing, please contact your
local authorized deal for replacement.
1.2 Getting to Know Your Camera
TV-IP110 (Front/Back View)
TV-IP110W (Front/Back View)
Power LED: A steady orange light indicates the camera is
powered on.
Link LED: A flash green light indicates the camera’s network
connection correctly.
Detachable Antenna (TV-IP110W only):
The detachable external antenna allows you to adjust its position to
obtain the maximum signal.
Camera Stand Connection: Connects the camera with the camera
stand.
Power Connector: Connects the AC power adapter to supply
power to the camera.
LAN Port: It is used to connect the network RJ-45 cable, which
supports the NWay protocol so that the camera can detect the
network speed automatically.
Reset Button: Reset will be initiated when the reset button is
pressed once. The power LED begins to flash.
Factory Reset will be initiated when the reset button is pressed continuously
for three seconds or when Power LED begins to light up. Release the reset
button and the Power LED will begin to flash.
1.3 Features and Benefits

Surveillance Supported
Enable motion detection and setup automated email alerts and upload
FTP for security.

Remote Control Supported
By using a standard Web browser or the bundled SecurView software
application, the administrator can easily change the configuration of the
camera via Intranet or Internet. In addition, the camera can be upgraded
remotely when a new firmware is available. The users are also allowed
to monitor the image and take snapshots via the network.

Multiple Platforms Supported
The camera supports multiple network protocols, including TCP/IP,
SMTP e-mail, HTTP, and other Internet related protocols. Therefore,
you can use the camera in a mixed operating system environment, such
as Windows 2000, XP, and Vista.

Multiple Applications Supported
Through the remote access technology, you can use the cameras to
monitor various objects and places for your own purposes.
For example, babies at home, patients in the hospital, offices and banks,
and more. The camera can capture both still images and video clips, so
that you can keep the archives and restore them at any time.
1.4 System Requirement

Networking
LAN: 10Base-T Ethernet or 100Base-TX Fast Ethernet.
WLAN: IEEE 802.11b/g. (For TV-IP110W)

Accessing the Camera using Web Browser
Platform:
Microsoft® Windows® 2000/XP/Vista
Macintosh OSX
CPU:
Intel Pentium III 350MHz or above
RAM:
128MB
Resolution:
800x600 or above
User Interface: Microsoft® Internet Explorer 6.0 or above

Accessing the Camera using SecurView
Platform:
Microsoft® Windows® 2000/XP/Vista.
Hardware Requirement:
1 camera connected: Intel Pentium III 800MHz; 512MB RAM
2 ~ 4 cameras connected: Intel Pentium 4 1.3GHz; 512MB RAM
5 ~ 8 cameras connected: Intel Pentium 4 2.4GHz; 1GB RAM
9 ~ 16 cameras connected: Intel Pentium 4 3.4GHz; 2GB RAM
Resolution:
1024x768 or above
NOTE If you connect multiple cameras to monitor various places
simultaneously, you are recommended to use a computer with
higher performance.
C HAPTER 2
H ARDWARE I NSTALLATION
2.1 Installing the Camera Stand
The camera comes with a camera stand, which uses a swivel ball screw
head to lock to the camera’s screw hole. When the camera stand is attached,
you can place the camera anywhere by mounting the camera through the
three screw holes located in the base of the camera stand.
The Camera Stand
2.2 Connecting the Camera to LAN
Connects an Ethernet cable to the
LAN port located on the Camera’s real
panel, and then attaches it to the
network.
Connects an antenna to the antenna
connector. (TV-IP110W)
Attach the external power supply to
the DC power input connector located
on Camera’s real Panel, and then
connect it to your local power supply.
NOTE Please configure the wireless setting via the wire connection.
2.3 Applications of the Camera
The camera can be applied in multiple applications, including:

Monitor local and remote places and objects via Internet or Intranet.

Capture still images and video clips remotely.

Upload images or send email messages with the still images attached.
The following diagram explains one of the typical applications for your
camera and provides a basic example for installing the camera.
*
C HAPTER 3
A CCESSING THE C AMERA
3.1 Using IP Setup
The camera comes with a conveniently utility, IP Setup, which is included
in the Installation CD-ROM, allowing you to search the camera on your
network easily.
1.
Insert the Installation CD-ROM into your computer’s CD-ROM drive
to initiate the Auto-Run program.
2.
Click the IP Setup from the Auto-Run menu screen. Then IP Setup
Wizard will appear. Click “Next” when the Welcome to the IPSetup
Setup Wizard appears.
3.
Click “Browse” to choose the desired destination location. By default,
the destination location is C:\Program Files\TRENDnet\IPSetup. Then
Click “Next”.
4.
Click “Next” to confirm the IPSetup software to be installed to the
computer.
5.
When the Installation Complete window appears, click “Finish”.
6.
After installing the IPSetup utility, the application is automatically
installed to your computer, and creates a folder in “ Start
\Program\TRENDnet\IPSetup”.
7.
Click Start > Programs > TRENDnet > IPSetup, and then click
IPSetup
8.
The IPSetup window will appear. It will search the Camera within the
same network.
Camera Display Area
-
Camera Display Area: It shows the connected camera(s) within the
same network.
Double click the IP address; it will link to Camera’s Web Configuration
page.
-
Change IP: Click this button to bring up the following window. It
allows you to change the IP Address. You can select either Static IP or
click DHCP. Then, enter the Administrator ID & password. By
default ID/password is: admin. When complete, click “Change”.
-
Search: Click this button to search the connected camera in the
same network.”
-
Exit: Click this button to exit the program.
3.2 Accessing to the Camera
1.
Open the Web browser on your computer (example showed in the
User’s Guide is based on the Internet Explorer)
2.
Type the default IP address (192.168.10.30) and then press [Enter].
3.
When the login window appears, enter the default User name (admin)
and password (admin) and press OK to access to the main screen of the
camera’s Web Configuration.
NOTE If you are initially access to the camera, you will be ask to install a
new plug-in for the camera. Permission request depends on the
Internet security settings of your computer. Click Yes to proceed.
After you login into the Web Configuration of the camera, the main page
will appear as below:
Camera Information
Zoom In
Live View/ Setup
Function
Live View Image
The main page of the Web Configuration provides you with many useful
information and functions, including:

Camera Information – Display the camera’s location and the current
date & time. The information can be modified in the Web
Configuration.

Live View Image – Displays the real-time image of the connected
camera.

Zoom In – Click the buttons to zoom in the live view image by 1x, 2x,
and 3x.

Live View/Setup Switch – Click Setup to configure the camera. For
details, see Chapter 4.

Function – Use these buttons to control the video functions.
 Manual Record allows you to record and save a video clip.
 Snapshot allows you to capture and save a still image.
 Browse allows assign the destination folder to store the video clips
and still images.
3.3 Configuring the IP Address of the PC
If you are failed to access to the camera, please check the IP address of your
computer. When you connect the camera to your computer directly to
proceed with configuration of the camera, you need to set up the IP
addresses to be in the same segment for the two devices to communicate.
1.
On your computer, click Start > Control Panel to open the Control
Panel window.
2.
Double-click Network Connection to open the Network Connection
window.
3.
Right-click Local Area Connection and then click Properties from
the shortcut menu.
4.
When the Local Area Connection Properties window appears, select the
General tab.
5.
Select Internet Protocol [TCP/IP] and then click Properties to bring
up the Internet Protocol [TCP/IP] Properties window.
6.
To configure a fixed IP address that is within the segment of the camera,
select the Use the following IP address option. Then, enter an IP
address into the empty field. The suggested IP address is 192.168.10.x
(x is 0~254 except 30), and the suggested Subnet mask is
255.255.255.0.
7.
When you are finished, click OK.
C HAPTER 4
C ONFIGURING THE C AMERA
4.1 Using the Web Configuration
You can access and manage the camera through the Web browser or from
the SecurView™ software (see chapter 5 in more detail). This chapter
describes the Web Configuration, and guides you through the configuration
of the camera by using the web browser.
To configure the camera, click Setup on the main page of Web
Configuration. The Web Configuration will start from the Basic page.
The Web Configuration contains the settings that are required for the
camera in the left menu bar, including Smart Wizard, Basic, Network,
Video, Event Server, Motion detect, Event Config, Tools, and
Information.
4.2 Using Smart Wizard
The camera’s Smart Wizard lets you configure your camera easily and
quickly. The wizard will guide you through the necessary settings with
detailed instructions on each step.
To start the wizard, click Smart Wizard in the left menu bar.
Step 1. Camera Settings
Step 2. IP Settings
Step 3. Email Settings
Step 4. Wireless Networking (for TV-110W only)
Step 5. Confirm Settings
This step shows the configuration of your camera. When you confirm the
settings, click Apply to finish the wizard and reboot the camera. Otherwise,
click Prev to go back to the previous step(s) and change the settings; or
click Cancel to end the wizard and discard the changes.
4.3 Basic Setup
The Basic menu contains three sub-menus that provide the system settings
for the camera, such as the Camera Name, Location, Date & Time, and User
management.
Basic >> System

Basic
Camera Name: Enter a descriptive name for the camera.
Location: Enter a descriptive name for the location used by the
camera.

Indication LED
This item allows you to set the LED illumination as desired. There are
two options: Normal and OFF.
Basic >> Date & Time
v

Date & Time
TimeZone: Select the proper time zone for the region from the pulldown menu.
Synchronize with PC: Select this option and the date & time
settings of the camera will be synchronized with the connected
computer.
Synchronize with NTP Server: Select this option and the time will
be synchronized with the NTP Server. You need to enter the IP
address of the server and select the update interval in the following
two boxes.
Manual: Select this option to set the date and time manually.
Basic >> User

Administrator
To prevent unauthorized access to the camera’s Web Configuration,
you are strongly recommend to change the default administrator
password. Type the administrator password twice to set and confirm the
password.

General User
User Name: Enter the user’s name you want to add to use the
camera.
Password: Enter the password for the new user.
When you are finished, click Add/Modify to add the new user to the
camera. To modify the user’s information, select the one you want to
modify from User List and click Add/Modify.
User List: Display the existing users of the camera. To delete a user,
select the one you want to delete and click Delete.

Guest
User Name: Enter the guest’s name you want to add to use the
camera.
Password: Enter the password for the new guest.
User List: Display the existing guests of the camera. To delete a user,
select the one you want to delete and click Delete.
NOTE The “General User” can access the camera and control the Function
buttons of the camera’s Web Configuration; the “Guest’ can only
view the live view image from the main page of the Web
Configuration while accessing the camera. Only the “Administrator”
is allowed to configure the camera through the Web Configuration.
4.4 Network Settings
The Network menu contains three sub-menus that provide the network
settings for the camera, such as the IP Setting, DDNS Setting, IP Filter, and
wireless network.
Network >> Network

IP Setting
This item allows you to select the IP address mode and set up the
related configuration.
DHCP: Select this option when your network uses the DHCP server.
When the camera starts up, it will be assigned an IP address from the
DHCP server automatically.
Static IP: Select this option to assign the IP address for the camera
directly. You can use IPSetup to obtain the related setting values.
IP
Enter the IP address of the camera. The default
setting is 192.168.10.30.
Subnet Mask
Enter the Subnet Mask of the camera. The
default setting is 255.255.255.0.
Default Gateway
Enter the Default Gateway of the camera. The
default setting is 192.168.10.1.
Primary/
Secondary DNS
DNS (Domain Name System) translates domain
names into IP addresses. Enter the Primary DNS
and Secondary DNS that are provided by ISP.
PPPoE: Select this option when you use a direct connection via the
ADSL modem. You should have a PPPoE account from your Internet
service provider. Enter the User Name and Password. The camera
will get an IP address from the ISP as starting up.
NOTE Once the camera get an IP address from the ISP as starting up, it
automatically sends a notification email to you. Therefore, when you
select PPPoE as your connecting type, you have to set up the email
or DDNS configuration in advance.

DDNS Setting
With the Dynamic DNS feature, you can assign a fixed host and
domain name to a dynamic Internet IP address. Select the Enable
option to enable this feature. Then, select the Provider from the pulldown list and enter the required information in the Host Name, User
Name, and Password boxes. Please note that you have to sign up for
DDNS service with the service provider first.

UPnP
The camera supports UPnP (Universal Plug and Play), which is a set of
computer network protocols that enable the device-to-device
interoperability. In addition, it supports port auto mapping function so
that you can access the camera if it is behind an NAT router or firewall.
Select the Enable option to enable this feature.

Ports Number
HTTP Port: The default HTTP port is 80.
RTSP Port: Configure the transmission of streaming data within the
network. The default RTSP (Real Time Streaming Protocol) port is
554.
NOTE If the camera is behind an NAT router of firewall, the suggested to
be used is from 1024 to 65535.
Network >> IP Filter
The IP Filter setting allows the administrator of the camera to limit the users
within a certain range of IP addresses to access the camera.

Start/End IP Address
Assign a range of IP addresses that are not allowed to access the
camera by entering the Start IP address and End IP address. When you
are finished, click Add to save the range setting. You can repeat the
action to assign multiple ranges for the camera.
For example, when you enter 192.168.10.50 in Start IP Address and
192.168.10.80 in End IP Address, the user whose IP address located
within 192.168.10.50 ~ 192.168.10.80 will not be allowed to access the
camera.

Deny IP List
The list displays the range setting(s) of IP addresses that are not
allowed to access the camera. To clear the setting, select a range of IP
addresses from the list and click Delete.
Network >> Wireless Setting (for TV-IP110W only)

Wireless
The camera supports WLAN while you use the wireless network.
Select the Enable option to enable this feature.
Network ID (SSID}: The default SSID setting is “TRENDnet”. To
connect the camera to a specified access point, set a SSID for the
camera to correspond with the access point’s ESS-ID. To connect the
camera to an
Ad-Hoc wireless workgroup, set the same wireless channel and SSID
to match with the computer’s configuration.
Click Site Survey to display the available wireless networks, so that
you can easily connect to one of the listed wireless networks.
List of searching results
Wireless Mode: Select the type of wireless communication for the
camera: Infrastructure or Ad-Hoc.
Channel: Select the appropriate channel from the list.
Authentication: Select the authentication method to secure the
camera from being used by unauthorized user: Open, Shared-key,
WPA-PSK, and WPA2-PSK. The following table explains the four
options:
Open
The default setting of Authentication mode, which
communicates the key across the network.
Shared-key
Allow communication only with other devices with
identical WEP settings.
WPA-PSK/
WPA2-PSK
WPA-PSK/WPA2-PSK is specially designed for the
users who do not have access to network
authentication servers. The user has to manually enter
the starting password in their access point or gateway,
as well as in each PC on the wireless network.
If you select Open or Shared-key as the Authentication mode, you
need to complete the following settings:
Encryption: Select the WEP option to enable the data encryption
feature to secure the camera within the wireless network.
Format: Once you enable the Encryption feature, you need to
determine the encryption format by selecting ASCII or HEX.
ASCII format causes each character you type to be interpreted as
an eight-bit value. Hex format causes each pair of characters you
type to be interpreted as an eight-bit value in hexadecimal (base 16)
notation.
Key Length: Select the WEP key length you use: 64 bits or 128
bits.
WEP Key 1/2/3/4: Enter the WEP key(s) in the following boxes.
If you select WPA-PSK or WPA2-PSK as the Authentication mode,
you need to complete the following settings:
Encryption: Select TKIP or AES. TKIP (Temporal Key Integrity
Protocol) changes the temporal key every 10,000 packets to insure
much greater security than the standard WEP security. AES
(Advanced Encryption Standard) is used to ensure the highest
degree of security and authenticity for digital information.
Pre-Shared Key: This is used to identify each other in the
network. Enter the name in the box, and this name must match the
Pre-shared key value in the remote device.
4.5 Setting up Video
The Video contains three sub-menus that provide the video and settings for
the camera.
Video >> Camera

Image Setting
Brightness: Adjust the brightness level from 0 ~ 100.
Contrast: Adjust the contrast level from 0 ~ 100.
Saturation: Adjust the colors level from 0 ~ 100.
Click Default to restore the default settings of the three options
above.
Mirror: Select the Horizontal option to mirror the image
horizontally. Select the Vertical option to mirror the image vertically.
Light Frequency: Select the proper frequency according to the
camera’s location: 50Hz, 60Hz, or Outdoor.

Overlay Setting
Includes Date & Time: Select this option to display the date & time
stamp on the live view image.
Enable Opaque: Select this option to set a black background to the
displayed date & time stamp.

MJPEG
Video Resolution: Select the desired video resolution from the three
formats: VGA, QVGA and QQVGA. The higher setting (VGA)
obtains better video quality while it uses more resource within your
network.
Video Quality: Select the desired image quality from five levels:
Lowest, Low, Medium, High, and Highest.
Frame Rate: Select a proper setting depending on your network
status.
NOTE The camera supports MJPEG compression. MJPEG capture the
images in JPEG format, which require higher bandwidth to view
smooth video. The administrator can control the bandwidth of each
connection well through the setting options above.
4.6 Event Server Configuration
The Event Server menu contains three sub-menus that allow you to upload
images to FTP, send emails that include still images, and store the images to
a NAS system.
When you complete the required settings for FTP, Email, or Network
Storage, click Test to test the related configuration is correct or not. Once
the camera connects to the server successfully, click Apply.
Event Server Setting>> FTP

FTP
Host Address: Enter the IP address of the target FTP server.
Port Number: Enter the port number used for the FTP server.
User Name: Enter the user name to login into the FTP server.
Password: Enter the password to login into the FTP server.
Directory Path: Enter the destination folder for uploading the
images. For example, /Test/.
Passive Mode: Select the Enable option to enable passive mode.
Event Server Setting >> Email

Email
SMTP Server Address: Enter the mail server address. For example,
mymail.com.
Sender Email Address: Enter the email address of the user who will
send the email. For example, [email protected]
Sender User Name: Enter the user name to login the mail server.
Sender Password: Enter the password to login the mail server.
Receiver #1 Email Address: Enter the first email address of the user
who will receive the email.
Receiver #2 Email Address: Enter the second email address of the
user who will receive the email.
Event Server Setting >> Network Storage

Net Storage
Samba Server Address: Enter the IP address of the Network
Storage server. For example: 192.168.10.51.
Share: Assign the folder on the Network Storage server to share the
files to users. For example, SAC7001-e1.
Path: Assign the path for uploading the files on the Network Storage
server. For example, /ts-u200 /.
User Name: Enter the user name to login into the Network Storage
server.
Password: Enter the password to login into the Network Storage
server.
Split By: When the file is too large to upload smoothly, use this
option to split it by selecting File Size or Recording Time.
When Disk Full: Select Stop Recording or Recycle – Delete
Oldest Folder of File when the storage space on the Network
Storage server is full.
4.7 Motion Detect
The Motion Detect menu contains the command and option that allow you
to enable and set up the motion detection feature of the camera. The camera
provides two detecting areas.
To enable the detecting area, select Window 1 or 2 from the pull-down list,
and then select Enable. When the detecting area is enabled, you can use the
mouse to move the detecting area and change the area coverage.
Name: Assign a name to the detecting area.
Threshold: Move the slide bar to adjust the level for detecting
motion to record video.
4.8 Event Config
The Event Config menu contains four sub-menus that provide the
commands to configure event profiles.
Event Configuration >> General Setting
Snapshot/Recording Filename Prefix: You can assign a given
prefix to each new captured file. Otherwise, leave this option blank
to use the default setting.
Network Storage Recording Time Per Even: Limit the recording
time while you are using the Network Storage solution.
Event Configuration >> Arrange Schedule Profile
This sub-menu displays the scheduled profile(s). To customize the profile,
click Add and then enter a descriptive name for the profile in the prompt
dialog window.
After entering the profile name, click OK and the profile is added to the
Schedule Profiles list. To delete the profile, select the profile in the list and
click Delete.
Profile Name: Display the profile name that you select in the
Schedule Profiles list.
Weekdays: Select the weekday(s) that you want to separately assign
in the schedule profile. The weekday that has been assigned will be
displayed with green color.
Time List: Display the time period that you have assigned within the
selected weekday. To assign the same time period to every weekday,
click Add this to all weekdays; click Delete this from all weekdays
to remove the selected time period from every weekday. Click Delete
to remove the selected time period.
Start/End Time: Enter the start and end time and then click Add to
assign a time period within in the selected weekday.
Event Configuration >> Motion Detect Trigger
Select the Enable option to enable the trigger function of the camera, so
that you can send captured images within the detecting area to the FTP
server, email receiver, Network Storage server, or the connected USB
device. You have to configure corresponding settings, such as FTP server
and email server, to enable this feature.
Schedule Profile: Select a schedule profile from the pull-down list.
Action: Select the destination that the captured images will be sent to:
Send Email, FTP Upload, Record to Network Storage, or Save
Image to USB.
Event Configuration >> Schedule Trigger
You can separately configure the schedule for trigger function of the camera
by Email, FTP, or Network Storage. Select the Enable option on each
item, and then select a Schedule Profile from the pull-down list and set the
Interval time.
NOTE If the setting value of the Network Storage Recording Time per
Event option in General Setting is longer than the Interval time in
Network Storage Schedule, the recorded file will be a continuous
video clip.
For example, if you set the Network Storage Recording Time Per
Event as 10 seconds and the Interval as 5 seconds, recorded file
becomes a non-stop video clip because the camera will record a 10second video clip every 5 seconds.
4.9 Tools
The Tools menu provides the commands that allow you to restart or reset
the camera. You can also backup and restore your configuration, and
upgrade the firmware for the camera.

Factory Reset
Click Reset to restore all factory default settings for the camera.

System Reboot
Click Reboot to restart the camera just like turning the device off and
on. The camera configuration will be retained after rebooting.

Configuration
You can save your camera configuration as a backup file on your
computer. Whenever you want to resume the original settings, you can
restore them by retrieving the backup file.
Backup: Click Get the backup file to save the current configuration
of the camera.
Restore: Click Browse to locate the backup file and then click
Restore.

Update Firmware
This item displays the current firmware version. You can upgrade the
firmware for your camera once you obtained a latest version of
firmware.
Select the firmware: Click Browse to locate the backup file
(xxx.pck) and then click Update. Factory reset and IP Setup are
required after firmware update.
NOTE Make sure to keep the camera connected to the power source during
the process of upgrading firmware. Otherwise, the camera might be
damaged because of failure of upgrading firmware.
4.10 Information
The Information menu displays the current configuration and events log of
the camera.

Device Info
Display the Basic, Video, Network, and Wireless settings of the camera.

System Log
The Logs table displays the events log recorded by the system.
C HAPTER 5
S ECURV IEW ™ S OFTWARE
This Chapter describes detail instructions on operating SecurView™
software, a useful friendly application for ease of control and navigation
requirement.
5.1
INSTALLATION
1.
Insert the Installation CD-ROM into your computer’s CD-ROM drive
to initiate the Auto-Run program.
2.
Click the SecurView from the Auto-Run menu screen.
NOTE To use SecurView™, you must have Microsoft .NET Framework
2.0 installed in the computer. The setup wizard will detect it and, if
the program is not installed yet, ask you to install it during the
process of installing SecurView™.
3.
Then SecurView Setup Wizard will appear. Click “Next” when the
Welcome to the SecurView Setup Wizard appears.
4.
Click “Browse” to choose the desired destination location. By default,
the destination location is C:\Program Files\TRENDnet\SecurView.
Then Click “Next”.
5.
Click “Next” to confirm the SecurView software to be installed to the
computer.
6.
When the Installation Complete window appears, click “Close”.
7.
After installing the IPSetup utility, the application is automatically
installed to your computer, and creates a folder in “ Start
\Program\TRENDnet\SecurView”.
5.2
1.
USING INSTALLATION
To launch the program, click Start > Program > TRENDnet >
SecurView, and then click SecruView™. The main screen will appear
as below.
NOTE Please set the resolution to 1024x768 or above on your computer
while using SecurView™; otherwise, the displayed main screen may
be distorted.
Item features
The following describes the function of each item on the main screen:

CONTROLS Panel
SETTING: Click to enter the Setting screen of SecurView™. Click
again to return to the main screen of SecurView™.
PLAY: Click to play the recorded video file using the media player
on the computer (for example, Windows Media Player by default).
LOCK: Click to lock the camera controls. Click again to resume
controls for the camera. If you have set ID and Password in
SETTING > Account, you will be asked to enter the required
information to unlock.
ALL RECORD: Click to start recording video clips using ALL
connected cameras. To stop recording, please click Record button
to stop the individual camera. Please note: stop recording only
stop the manual recording camera. For schedule recording, please
change the setting on configuration.
TIP

By default, the ID and Password boxes are “blank.” Click
SETTING > Account to change the ID and password of
lock/unlock function.
VIEW SELECTION Panel
View mode buttons: SecurView™ provides multiple view modes,
including 1/4/9/16 windows and Full screen mode.
SCAN: When multiple cameras connected, click this button to
display the video views between cameras. Click the Scan button
again to stop scanning.
PREV: When multiple cameras connected, click this button to
switch the video view to the previous camera.
NEXT: When multiple cameras connected, click this button to
switch the video view to the next camera.
TIP
To set the time interval of scanning, click SETTING > Other and
then adjust the time from 1 to 10 seconds in the Time interval of
scan option.

CAMERA Panel
TRIGGER OUT: Click to turn on the trigger out connector of the
camera. This button is available only when the connected camera
supports the trigger out connector, which is used to control the
external device connected to the camera, such as a light. (Not support
on these models)
SNAPSHOT: Click to capture a still image using the selected
camera and save the file in the computer.
RECORD: Click to start recording a video clip using the selected
camera. Click again to stop recording and save the file in the
computer.
TALK: Click to speak out through the camera. Please note only one
user is allowed to use this function at the same time. (Not support on
these models)
LISTEN: Click to receive the on-site sound and voice from the
camera. (Not support on these models)

SYSTEM Panel
This panel displays the current date and time.

PAN-TILT CONTROL Panel (Not support on these models)
When you connect a pan/tilt camera, the system will detect the
camera’s function automatically and the PAN-TILT CONTROL
buttons will become functional. Otherwise, these buttons are displayed
as gray out buttons.
Direction/Home buttons: Click these buttons to adjust the camera’s
viewing angle to Up (
) / Down (
) / Left (
) / Right
(
) / Left-Up (
) / Left-Down (
) / Right-Up (
)/
Right-Down (
).
Click the Home button (
position.
) to return the camera to the default
SWING: If you have saved two or more positions for the selected
camera, click this button to control the camera swinging from one
position to another position.

Video View Window and Camera List
Video Viewing
Window
Camera List
Video Viewing Window: This window displays the video view of
the selected camera, which can be divided into 4/9/16 windows
according to your selection in VIEW SELECTION panel.
Camera List: This list displays the information of the connected
camera(s).
 To add a camera
1.
Click SETTING in the CONTROLS panel to display the Setting
screen.
2.
Click Add New Camera.
3.
In the pop-up Add New Camera dialog window, you can:
 Select the Search tab if you are not sure of the camera’s IP address.
Click Search camera to search the available camera within the
network. Once the camera is found and is shown in the list, select
it and click Add Camera.
 Select the Input tab to add a camera by entering its IP address
directly. Enter the camera’s IP address (default: 192.168.10.30)
and Port (default: 80), and then click Add Camera.
4.
Enter the User name and Password for the camera, and then click OK.
The connected camera will be displayed in the Camera List.
5.
Click SETTING to return to the Video View Window. The video view
of the selected camera will be displayed now.
To remove a camera
1.
Click SETTING in the CONTROLS panel to display the Setting
screen.
2.
Select a camera from the list and click Delete Camera.
Select a camera
Delete the camera
To link to the Web page of the camera
Click SETTING > Camera List > Camera Configuration and then Link
web page to launch the Web browser that displays live view image and
Web Configuration of the selected camera.
To record video
SecurView™ provides three methods to record video clips: one is to click
the RECORD/All Record button to record manually; the second is to
record by motion detection; the third is to set the recording schedule in
Setting > Recording Configuration > Schedule Recording
Configuration.

Manually recording
Click RECORD/All Record and it starts recording. Click the button
again to stop.

Trigger recording by motion detection
When the motion detection function of the selected camera is enabled,
you can configure the camera to start recording triggered by the
motion detected. Click SETTING > Motion Configuration, and
then select the Recording option to enable the selected camera to
record by motion detection.

Schedule recording Configuration
This recording method will work after you have completed the
required settings in Schedule Recording Configuration. The
recording schedule can be defined by Dates or Days.
Dates: Select the camera from the pull-down list..
Select a camera
Add Schedule
Then, click Add to set the Start/Stop date and time and then click
OK to add the recording schedule to the list.
Click Apply to save the settings
Days: First, select the camera from the pull-down list and select
Days tab. Then, select the weekday from the day buttons and then set
the time period. Click Apply to save the settings.
To configure the recording settings
To configure the recording settings, including the storage folder and storage
options, click SETTING > Recording Configuration.

Recording File Path: To change the destination folder to save the
recorded video file, click Browse under the Recording File Path
box to assign a new folder.

Each Recording File Size: This option allows you to select from 20
to 100 MB so that the video will be recorded as another file
automatically when the recording file reaches the specified size limit.

Reserved HDD space for each camera: This option allows you to
set to reserve the storage space on the hard disk drive for the
recording of each camera. Before setting the reserve space on the
hard disk drive, you can check the available storage space that is
displayed in the HDD Free space field.

Enable Recycle Recording: Click on the camera number to clear the
files when the unreserved space of the hard disk drive is full.
To playback the recorded video
The recorded video clips are saved in your computer, and can be played
using the media player on the computer, such as Windows Media Player.
To start playback, simply click the PLAY button on the CONTROLS panel,
and the following dialog screen will appear, allowing you to select the file
to playback.
Select the recorded video file under the [camera] path and then click Open
to launch the media player to playback.
NOTE If your player on the computer don’t have video codec to playback
the recorded video. You can download video codec from
http://www.xvid.org/downloads.15.0.html to support.
To set up motion detection options
When the motion detection function of the selected camera is enabled, you
can set the Motion Options by selecting Alarm, Recording, Send e-Mail,
and Trigger Out under SETTING > Motion Configuration.

Alarm: Select Beep or Music to alert you for the motion detected.
When you select Music, you can customize the sound by clicking
Browse and then selecting your favorite music (*.wav or *.mp3 file)
in the computer.

Recording: Select this option to enable the camera to record by
motion detected.

Send Email: Select this option so that the system will be able to send
an email to the specified receiver. Once the option is selected, you
have to complete the required information in SETTING > Motion
Configuration > Email Configuration.
Mail Server: Enter the mail server address. For example,
mymail.com.
Mail From: Enter the email address of the user who will send the
email. For example, [email protected]
Mail To: Enter the email address of the user who will receive the
email.
User Name: Enter the user name to login the mail server.
Password: Enter the password to login the mail server.
Subject: Enter a subject for the notification email.

Trigger Out: If the selected camera supports Trigger Out connector,
select this option to enable the Trigger Out function.
Account
Click SETTING > Account to setup the username & password to lock &
unlock the main screen of the SecurView.
Other
Click SETTING > Other to setup the scanning time between cameras. The
default setting is 2 seconds. You can set the interval time between 2 ~ 20
seconds.
Information
Click SETTING > About to display the information of the software
application.
C HAPTER 6
A PPENDIX
A.1 Specification




Image Sensor
Sensor
Resolution
1/4” color CMOS
640x480
Video
Compression
Video resolution
MJPEG
VGA/QVGA/QQVGA; 30fps max.
System Hardware
Processor
RAM
ROM
Power
ARM9 base
16MB SDRAM
4MB NOR Flash
DC 5V, 2.5AV
Communication
LAN
WLAN
Protocol support

User Interface
LAN
Antenna
Reset
10/100Mbps Fast Ethernet, auto-sensed,
Auto-MDIX
IEEE 802.11b/g
TCP/IP, UDP, ICMP, DHCP, NTP, DNS, DDNS,
SMTP, FTP, Samba, PPPoE, UPnP
One RJ-45 port
One detachable antenna
One reset button
LEDs

Power LED (orange); Link LED (green)
SecurView™ Software
OS Support
Windows 2000/XP/Vista
Feature
playback/recording/configuration features

Web Configuration
OS Support
Windows 2000/XP/Vista
Browser
Internet Explorer 6.0 or above

Operating Environment
Temperature
- Operation: 5C ~ 45C
- Storage: -15C ~ 60C
Humidity

- Operation: 20% ~ 85% non-condensing
- Storage: 0% ~ 90% non-condensing
EMI
FCC Class B, CE Class B
A.2
Glossary of Terms
NUMBERS
10BASE-T
100BASE-TX
10BASE-T is Ethernet over UTP Category III, IV, or V
unshielded twisted-pair media.
The two-pair twisted-media implementation of 100BASE-T is
called 100BASE-TX.
A
ADPCM
AMR
Applet
ASCII
ARP
AVI
Adaptive Differential Pulse Code Modulation, a new
technology improved from PCM, which encodes analog
sounds to digital form.
AMR (Adaptive Multi-Rate) is an data compression scheme
optimized for speech coding, which is adopted as the standard
speech codec by 3GPP.
Applets are small Java programs that can be embedded in an
HTML page. The rule at the moment is that an applet can only
make an Internet connection to the computer form that the
applet was sent.
American Standard Code For Information Interchange, it is the
standard method for encoding characters as 8-bit sequences of
binary numbers, allowing a maximum of 256 characters.
Address Resolution Protocol. ARP is a protocol that resides at
the TCP/IP Internet layer that delivers data on the same
network by translating an IP address to a physical address.
Video Interleave, it is a Windows platform and video file type,
a common format for small movies and videos.
B
BOOTP
C
Bootstrap Protocol is an Internet protocol that can
automatically configure a network device in a diskless
workstation to give its own IP address.
Communication
Connection
Communication has four components: sender, receiver,
message, and medium. In networks, devices and application
tasks and processes communicate messages to each other over
media. They represent the sender and receivers. The data they
send is the message. The cabling or transmission method they
use is the medium.
In networking, two devices establish a connection to
communicate with each other.
D
DHCP
DNS
Developed by Microsoft, DHCP (Dynamic Host Configuration
Protocol) is a protocol for assigning dynamic IP addresses to
devices on a network. With dynamic addressing, a device can
have a different IP address every time it connects to the
network. In some systems, the device's IP address can even
change while it is still connected. It also supports a mix of
static and dynamic IP addresses. This simplifies the task for
network administrators because the software keeps track of IP
addresses rather than requiring an administrator to manage the
task. A new computer can be added to a network without the
hassle of manually assigning it a unique IP address. DHCP
allows the specification for the service provided by a router,
gateway, or other network device that automatically assigns an
IP address to any device that requests one.
Domain Name System is an Internet service that translates
domain names into IP addresses. Since domain names are
alphabetic, they're easier to remember. The Internet however,
is really based on IP addresses every time you use a domain
name the DNS will translate the name into the corresponding
IP address. For example, the domain name
www.network_camera.com might translate to 192.167.222.8.
E
Enterprise
network
An enterprise network consists of collections of networks
connected to each other over a geographically dispersed area.
The enterprise network serves the needs of a widely distributed
company and operates the company’s mission-critical
applications.
Ethernet
The most popular LAN communication technology. There are
a variety of types of Ethernet, including 10Mbps (traditional
Ethernet), 100Mbps (Fast Ethernet), and 1,000Mbps (Gigabit
Ethernet). Most Ethernet networks use Category 5 cabling to
carry information, in the form of electrical signals, between
devices. Ethernet is an implementation of CSMA/CD that
operates in a bus or star topology.
F
Fast Ethernet
Firewall
Fast Ethernet, also called 100BASE-T, operates at 10 or
100Mbps per second over UTP, STP, or fiber-optic media.
Firewall is considered the first line of defense in protecting
private information. For better security, data can be encrypted.
A system designed to prevent unauthorized access to or from a
private network. Firewalls are frequently used to prevent
unauthorized Internet users from accessing private networks
connected to the Internet, especially Intranets all messages
entering or leaving the intranet pass through the firewall,
which examines each message and blocks those that do not
meet the specified security criteria.
G
Gateway
Group
A gateway links computers that use different data formats
together.
Groups consist of several user machines that have similar
characteristics such as being in the same department.
H
HEX
I
Short for hexadecimal refers to the base-16 number system,
which consists of 16 unique symbols: the numbers 0 to 9 and
the letters A to F. For example, the decimal number 15 is
represented as F in the hexadecimal numbering system. The
hexadecimal system is useful because it can represent every
byte (8 bits) as two consecutive hexadecimal digits. It is easier
for humans to read hexadecimal numbers than binary numbers.
Intranet
Internet
Internet address
IP
IP address
ISP
This is a private network, inside an organization or company
that uses the same software you will find on the public
Internet. The only difference is that an Intranet is used for
internal usage only.
The Internet is a globally linked system of computers that are
logically connected based on the Internet Protocol (IP). The
Internet provides different ways to access private and public
information worldwide.
To participate in Internet communications and on Internet
Protocol-based networks, a node must have an Internet address
that identifies it to the other nodes. All Internet addresses are
IP addresses
Internet Protocol is the standard that describes the layout of the
basic unit of information on the Internet (the packet) and also
details the numerical addressing format used to route the
information. Your Internet service provider controls the IP
address of any device it connects to the Internet. The IP
addresses in your network must conform to IP addressing
rules. In smaller LANs, most people will allow the DHCP
function of a router or gateway to assign the IP addresses on
internal networks.
IP address is a 32-binary digit number that identifies each
sender or receiver of information that is sent in packets across
the Internet. For example 80.80.80.69 is an IP address. When
you “call” that number, using any connection methods, you get
connected to the computer that “owns” that IP address.
ISP (Internet Service Provider) is a company that maintains a
network that is linked to the Internet by way of a dedicated
communication line. An ISP offers the use of its dedicated
communication lines to companies or individuals who can’t
afford the high monthly cost for a direct connection.
J
JAVA
Java is a programming language that is specially designed for
writing programs that can be safely downloaded to your
computer through the Internet without the fear of viruses. It is
an object-oriented multi-thread programming best for creating
applets and applications for the Internet, Intranet and other
complex, distributed network.
L
LAN
Local Area Network a computer network that spans a
relatively small area sharing common resources. Most LANs
are confined to a single building or group of buildings.
M
MJPEG
MJPEG (Motion JPEG) composes a moving image by storing
each frame of a moving picture sequence in JPEG
compression, and then decompressing and displaying each
frame at rapid speed to show the moving picture.
N
NAT
Network
NWay Protocol
Network Address Translator generally applied by a router that
makes many different IP addresses on an internal network
appear to the Internet as a single address. For routing messages
properly within your network, each device requires a unique IP
address. But the addresses may not be valid outside your
network. NAT solves the problem. When devices within your
network request information from the Internet, the requests are
forwarded to the Internet under the router's IP address. NAT
distributes the responses to the proper IP addresses within your
network.
A network consists of a collection of two or more devices,
people, or components that communicate with each other over
physical or virtual media. The most common types of network
are:
LAN – (local area network): Computers are in close distance
to one another. They are usually in the same office space,
room, or building.
WAN – (wide area network): The computers are in different
geographic locations and are connected by telephone lines or
radio waves.
A network protocol that can automatically negotiate the
highest possible transmission speed between two devices.
P
PCM
PING
PPPoE
Protocol
PCM (Pulse Code Modulation) is a technique for converting
analog signals into digital form for transmission.
Packet Internet Groper, a utility used to determine whether a
specific IP address is accessible. It functions by sending a
packet to the specified address and waits for a reply. It is
primarily used to troubleshoot Internet connections.
Point-to-Point Protocol over Ethernet. PPPoE is a specification
for connecting the users on an Ethernet to the Internet through
a common broadband medium, such as DSL or cable modem.
All the users over the Ethernet share a common connection.
Communication on the network is governed by sets of rules
called protocols. Protocols provide the guidelines devices use
to communicate with each other, and thus they have different
functions. Some protocols are responsible for formatting and
presenting and presenting data that will be transferred from file
server memory to the file server’s net work adapter Others are
responsible for filtering information between networks and
forwarding data to its destination. Still other protocols dictate
how data is transferred across the medium, and how servers
respond to workstation requests and vice versa. Common
network protocols responsible for the presentation and
formatting of data for a network operating system are the
Internetwork Packet Exchange (IPX) protocol or the Internet
Protocol (IP). Protocols that dictate the format of data for
transferors the medium include token-passing and Carrier
Sense Multiple Access with Collision Detection (CSMA/CD),
implemented as token-ring, ARCNET, FDDI, or Ethernet. The
Router Information Protocol (RIP), a part of the Transmission
Control Protocol/Internet Protocol (TCP/IP) suite, forwards
packets from one network to another using the same network
protocol.
R
RJ-45
Router
RJ-45 connector is used for Ethernet cable connections.
A router is the network software or hardware entity charged
with routing packets between networks.
S
Server
SIP
SMTP
SNMP
Station
Subnet mask
It is a simple computer that provides resources, such as files or
other information.
SIP (Session Initiated Protocol) is a standard protocol that
delivers the real-time communication for Voice over IP
(VoIP), which establishes sessions for features such as and
video conferencing.
The Simple Mail Transfer Protocol is used for Internet mail.
Simple Network Management Protocol. SNMP was designed
to provide a common foundation for managing network
devices.
In LANs, a station consists of a device that can communicate
data on the network. In FDDI, a station includes both physical
nodes and addressable logical devices. Workstations, singleattach stations, dual-attach stations, and concentrators are
FDDI stations.
In TCP/IP, the bits used to create the subnet are called the
subnet mask.
T
(TCP/IP)
Transceiver
U
Transmission Control Protocol/Internet Protocol is a widely
used transport protocol that connects diverse computers of
various transmission methods. It was developed y the
Department of Defense to connect different computer types
and led to the development of the Internet.
A transceiver joins two network segments together.
Transceivers can also be used to join a segment that uses one
medium to a segment that uses a different medium. On a
10BASE-5 network, the transceiver connects the network
adapter or other network device to the medium. Transceivers
also can be used on 10BASE-2 or 10BASE-T networks to
attach devices with AUI ports.
UDP
User Name
Utility
UTP
The User Datagram Protocol is a connectionless protocol that
resides above IP in the TCP/IP suite
The USERNAME is the unique name assigned to each person
who has access to the LAN.
It is a program that performs a specific task.
Unshielded twisted-pair. UTP is a form of cable used by all
access methods. It consists of several pairs of wires enclosed in
an unshielded sheath.
W
WAN
WEP
Windows
WPA
WPA2
Wide-Area Network. A wide-area network consists of groups
of interconnected computers that are separated by a wide
distance and communicate with each other via common carrier
telecommunication techniques.
WEP is widely used as the basic security protocol in Wi-Fi
networks, which secures data transmissions using 64-bit or
128-bit encryption.
Windows is a graphical user interface for workstations that use
DOS.
WPA (Wi-Fi Protected Access) is used to improve the security
of Wi-Fi networks, replacing the current WEP standard. It uses
its own encryption, Temporal Key Integrity Protocol (TKIP),
to secure data during transmission.
Wi-Fi Protected Access 2, the latest security specification that
provides greater data protection and network access control for
Wi-Fi networks. WPA2 uses the government-grade AES
encryption algorithm and IEEE 802.1X-based authentication,
which are required to secure large corporate networks.
Limited Warranty
TRENDnet warrants its products against defects in material and workmanship, under normal
use and service, for the following lengths of time from the date of purchase.
TV-IP110/TV-IP110W – 3 Years Warranty
If a product does not operate as warranted above during the applicable warranty period,
TRENDnet shall, at its option and expense, repair the defective product or part, deliver to
customer an equivalent product or part to replace the defective item, or refund to customer the
purchase price paid for the defective product. All products that are replaced will become the
property of TRENDnet. Replacement products may be new or reconditioned.
TRENDnet shall not be responsible for any software, firmware, information, or memory data
of customer contained in, stored on, or integrated with any products returned to TRENDnet
pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or attempt to service the
product by any unauthorized service center. This warranty is voided if (i) the product has been
modified or repaired by any unauthorized service center, (ii) the product was subject to
accident, abuse, or improper use (iii) the product was subject to conditions more severe than
those specified in the manual.
Warranty service may be obtained by contacting TRENDnet office within the applicable
warranty period for a Return Material Authorization (RMA) number, accompanied by a copy
of the dated proof of the purchase. Products returned to TRENDnet must be pre-authorized by
TRENDnet with RMA number marked on the outside of the package, and sent prepaid, insured
and packaged appropriately for safe shipment.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE
AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT
TRENDNET’S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STATUTORY
OR
OTHERWISE,
INCLUDING
WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING
AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT
DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S
MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED
ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE
OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER
HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW
TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY,
WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF
ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH
DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND
OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION. THIS DISCLAIMER OF
LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED
HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the state of
California.
AC/DC Power Adapter, Cable, Cooling Fan, and Power Supply carry 1 year warranty.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement