M24LR 86H
M24LR-DISCOVERY
M24LR-DISCOVERY evaluation kit
Data brief
Features
■
M24LR board
– M24LR04E-RMN6T/2 Dual Interface
EEPROM with I2C and ISO/IEC 15693 RF
interfaces, 4 Kbits of EEPROM and
password protection in SO8N package
– STM8L152C6T6 8-bit microcontroller, with
8 Kbytes of Flash memory
– STTS751-0WB3F, low-voltage digital
temperature sensor
– 20 x 40 mm inductive antenna etched on
the PCB
– Two function buttons (User and Reset)
Figure 1.
– SWIM connector for programming and
debugging
– I2C connectors
– LCD (24 segments, 4 commons)
■
RF transceiver board
– CR95HF-VMD5T 13.56 MHz multi-protocol
contactless transceiver IC with SPI and
UART serial access
– STM32F103CB 32-bit microcontroller, with
128 Kbytes of Flash memory
– 47 x 34 mm 13.56 MHz inductive antenna
etched on PCB and associated circuitry
– USB connector for communication with
host PC and demonstration board powering
M24LR board and RF transceiver board
M24LR board
RF transceiver board
July 2012
Doc ID 023090 Rev 1
For further information contact your local STMicroelectronics sales office.
1/4
www.st.com
4
Description
1
M24LR-DISCOVERY
Description
M24LR-DISCOVERY is a ready-to-use kit which features the M24LR04E-R Dual Interface
EEPROM IC. It addresses a wide range of applications such as industrial or medical
equipment and consumer electronics. This kit contains 2 different boards (see Figure 1):
●
The M24LR board is battery-less and is powered by RFID readers or NFC-enabled
phones supporting ISO/IEC 15693.
●
The RF transceiver board is an RFID reader demonstration board and is composed,
among other parts, of a CR95HF (13.56 MHz multi-protocol contactless transceiver IC
with SPI and UART serial access). This board has to be plugged in to a PC and comes
with a demonstration software.
The M24LR board also works with Android NFC phones supporting ISO/IEC 15693. An
application called NfcV-Reader is available on Google Play. Performance may vary
depending on NFC phone's RF management.
System requirements
●
●
1.1
Windows PC (2000, XP, Vista, 7)
ISO/IEC 15693 capable NFC phones
Demonstration software
The M24LRxx application software can be uploaded from www.st.com/m24lr04e-discovery
and installed on your PC. It consists in:
●
an M24LRxx application software
●
1.1.1
an STM8L firmware
M24LRxx application software
The PC software allows to:
1.
Launch M24LRxx_Application_Software.exe executable.
2.
Choose CR95HF DEMO KIT tab.
3.
Select demo NDEF messages tab.
4.
Click on demo NDEF & Energy Harvesting tab.
The latest versions of this demonstration source code and associated documentation can
be downloaded from www.st.com/m24lr04e-discovery.
1.1.2
STM8L firmware
Development toolchain
In case of an STM8L firmware change, the user has to download:
●
2/4
STMicroelectronics, ST Visual Develop (STVD)
Doc ID 023090 Rev 1
M24LR-DISCOVERY
Revision history
STM8L firmware
Demonstration software is preloaded in the board's Flash memory. This demonstration
displays on the LCD:
1.2
●
The text messages stored in the M24LR04E-R Dual Interface EEPROM
●
The internal voltage of the M24LR board
●
The ambient temperature measured from the sensor
Android application
Install the NfcV-Reader applet available from Google Play. This application enables the NFC
communication (Settings-Wireless & Networks-NFC) for evaluation on an Android device.
1. Download the NfcV-Reader App from Google Play and install it on the Android device.
2.
Launch the NfcV-Reader application.
3.
Place the device's NFC antenna close to the M24LR board antenna.
The NFC phone powers the M24LR board.
The text message can be changed using the NFC phone (select NDEF function and select
write NDEF message menu).
Performance may vary depending on NFC phone's RF management.
2
Revision history
Table 1.
Document revision history
Date
Revision
17-Jul-2012
1
Changes
Initial release.
Doc ID 023090 Rev 1
3/4
M24LR-DISCOVERY
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
4/4
Doc ID 023090 Rev 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement