Dyna-Glo CSA 2.14-2000 Instruction manual

Add to My manuals
14 Pages

advertisement

Dyna-Glo CSA 2.14-2000 Instruction manual | Manualzz

PROPANE CONSTRUCTION HEATER

Dyna-Glo ™ Delux

MODELS:

Dyna-Glo ™

MODELS:

USER’S INSTRUCTION MANUAL

RMC-FA40DLX (40,000 BTU/HR, FORCED - AIR)

RMC-FA100DLX (70,000/100,000 BTU/HR, FORCED - AIR)

RMC-FA150DLX (120,000/150,000 BTU/HR, FORCED - AIR)

RMC-FA40A (40,000 BTU/HR, FORCED - AIR)

RMC-FA50A (30,000/50,000 BTU/HR, FORCED - AIR)

RMC-FA100A (70,000/100,000 BTU/HR, FORCED - AIR)

RMC-FA150A (120,000/150,000 BTU/HR, FORCED - AIR)

CSA 2.14-2000, ANSI Z83.7-2000

FGENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTION PROVIDED

WITH THIS HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND

PROPERTY LOSS OR DAMAGE FROM HAZARDS OF FIRE EXPLOSION, BURN,

ASPHYXIATION, CARBON MONOXIDE POISONING, AND/OR ELECTRIC SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS

SHOULD USE OR SERVICE THIS HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN

INSTRUCTION MANUAL, LADLES, ETC. CONTACT THE MANUFACTURER.

FRETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

5/05 Rev.1

TABLE OF CONTENTS

• Introduction & Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

• General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

• Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

• Unpacking Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

• Size & Capacity Of Propane Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

• Installation To The Propane Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7

• Refilling The Propane Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7

• Leak Checking & Location Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

• Lighting & Shutdown Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

• Test Firing Heater & Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

• Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

• Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11

• Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

• Warranty Information

FWARNING:FIRE, BURN, INHALATION, AND EXPLOSION HAZARD, KEEP

SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR

CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS

RECOMMENDED BY THE INSTRUCTIONS.

NEVER USE THE HEATER IN SPACES WHICH DO OR MAY CONTAIN

VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS

GASOLINE, SOLVENTS, PAIN THINNERS, DUST PARTICLES OR UNKNOWN

CHEMICALS.

FWARNING: NOT FOR HOME OR RECREATIONAL VEHICLE USE.

Page 1

Dyna-Glo Propane Forced Air Construction Heaters

The heater is designed and approved for use as a construction heater under ANSI Z83.7., CSA2.14

It is hard to anticipate every use which may be made of this heater. CHECK WITH YOUR LOCAL

FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS.

Other standards govern the use of fuel gases and heat producing products in specific applications.

Your local authority can advise you about these.

IMPORTANT: Read this user's manual carefully and completely before trying to operate or service this heater. Improper use of this heater can cause serious injury or death from fire, explosion and carbon monoxide poisoning.

This is a direct-fired forced-air construction heater for either indoor or outdoor use. Its intended use is primarily the temporary heating of buildings or structures under construction, alteration or repair.

All the products of combustion generated by the heater are forced through the heater and released into the area being heated. This heater operates at approximately 98%+ combustion efficiency but still produces a small amount of carbon monoxide. Humans can tolerate small amounts of carbon monoxide for short periods. Carbon monoxide can build up in a heated space and failure to provide adequate ventilation could result in poisoning or death.

FWARNING: Not for use with ductwork.

SPECIFICATIONS:

Model No.

Input Rating

RMC-FA40DLX

RMC-FA40A

-

40,000 Btu/hr

Propane Type of Gas

Gas Supply Pressures to Regulator Maximum Cylinder Pressure

Minimum (for purpose of Input Adjustment)

5psig

Manifold Pressure 11” W.C.

Gas Consumption

Electrical Input

1.9lbs/hr

3.3lbs/hr

120V, 60Hz, 1 Ø

Amperage

Unload

Load

0.35A

0.63A

-

RMC-FA(50A)

30,000 Btu/hr

50,000 Btu/hr

Propane

RMC-FA100DLX

RMC-FA100A

70,000 Btu/hr

100,000 Btu/hr

Propane

RMC-FA150DLX

RMC-FA150A

120,000 Btu/hr

150,000 Btu/hr

Propane

Cylinder Pressure Cylinder Pressure Cylinder Pressure

5psig

10” W.C.

2.3lbs/hr

1.4lbs/h

5psig

9.5” W.C

4.6lbs/hr

3.3lbs/h - 5.6lbs/hr

8” W.C.

7lbs/hr

5.6lbs/hr

120V, 60Hz, 1 Ø 120V, 60Hz, 1 Ø

0.58A

0.75A

0.6A

0.8A

5psig

120V, 60Hz, 1 Ø

0.6A

0.8A

Fan

Unload

Load

3550rpm

3000rpm

3570rpm

3300rpm

3580rpm

3300rpm

3580rpm

3300rpm

Ignition Piezo/Manual Spark Continuous Spark Continuous Spark Continuous Spark

Spark Gap

Size (L x W x H)

Weight

0.16” 0.16” 0.16” 0.16”

18.1” x 7.7” x 12.8” 18.1” x 7.7” x 12.8” 25.12” x 9” x 15.5” 25.12” x 9” x 15.5”

15.2lbs (6.9kg) 15.2lbs (6.9kg) 22.7lbs (10.3kg) 22.7lbs (10.3kg)

Page 2

GENERAL SAFETY INSTRUCTIONS:

Accidents are always tragic especially because so many of them could have been prevented with little care and judgment. There are some basic good practices, we hope you will follow for safe use of your heater.

IMPORTANT SAFETY INFORMATION:

• Children should be carefully supervised, when they are in the area.

• Always maintain proper clearance from combustible materials. Minimum clearance from combustibles. Side - 24”; Top - 36”; Combustible and Front - 72”. Floor -noncombustible.

• Heater must be placed on level and adequate level and stable surface

• Never place anything including clothes or other flammable items on the heater.

• The appliance area shall be kept clear and free from combustible materials, gasoline and other flammable vapours and liquids.

• Do not modify or operate a heater which has been modified.

• Adequate clearance for accessibility and for combustion & ventilation air supply must be maintained at all times when the heater is operating.

• Service and repair should be done by a qualified service person. The heater should be inspected before each use and at least annually by a qualified person. More frequent cleaning may be required as necessary. Do not service while hot or operating.

• Never connect heater to an unregulated gas supply.

• The heater is shipped from the factory for LP(Propane) gas. This heater is for use with propane gas only, do not convert heater to any other gas. Installation must conform to local codes or, in the absence, with the standard for the Storage and Handling of Liquefied

Petroleum Gases ANSI/NFPA NFPA 58 and the Natural Gas and Propane Installation Code

CSA B149.1

• The minimum and maximum inlet pressures to the regulator from the gas tank are 5 psi and bottle pressure, respectively. Use only the regulator & hose assembly provided with the heater. Inspect the regulator/hose assembly prior to each use of the heater. If there is excessive abrasion or wear, or hose is cut, replace with regulator/hose assembly listed on the parts list prior to using this heater.

• Gas supply connections should be checked using a 50/50 solution of liquid dish soap and never use a flame to check for gas leaks.

• The electrical connection & grounding must comply with National Electrical Code.

ANSI/NFPA 70 or in Canada CSA C22.1, Canadian Electrical Code, Part 1. Use only a properly grounded three (3) prong receptacle.

• Do not restrict inlet or outlet by any means. The flow of combustion and ventilation air is not to be obstructed.

• Forced air heaters should not be directed toward any propane or gas container within 20 feet of the exit nozzle. The heater should also be located at least 6 feet away from any propane gas container

(regulations in Canada are 10 feet)

• The propane cylinder supply system must be arranged to provide for vapour withdrawal from the operating cylinder.

WARNING: Motor and fan must be running before lighting, during operation and at shutdown, in order to prevent a flame-out condition which could result in personal injury or property damage.

PRODUCT FEATURES:

• Portable, Stable & Fully Assembled • 100% Safety Shutoff System

• Wind Resistant & Rain Protected • Adjustable Input Ratings

• Continuous Spark Ignition or Piezo Electric Spark Ignition

Page 3

UNPACKING:

1. Remove heater from carton.

2. Remove all protective packing applied to heater for shipment.

3. Retain cartons and packaging material until unit is operated and found in good condition.

4. Checker heater for any shipping damage. If heater shows any external or internal damage, promptly inform dealer/distributor where you purchased heater.

INFORMATION ON SIZE * CAPACITY OR PROPANE GAS CYLINDERS:

The chart below shows the number and size of propane tanks needed to run this heater.

*

Less gas is vaporized at lower temperatures.

You may need two or more 100 pound tanks or one larger tank in colder weather.

Number of Tanks

Temperature (°F) At tank

40,000 BTU/h-

50,000BTU/h

100,000 BTU/h 150,000 BTU/h

Above 32°F 1 - 20lb 1 - 100lb 1 - 100lb

32°F 1 - 20lb 1 - 100lb 2 - 100lb

20°F 1 - 20lb 2 - 100lb 3 - 100lb

10°F

-10°F

1 - 20lb

2 - 20lb

3 - 100lb

Use Larger Tank

3 - 100lb

Use Larger Tank

-20°F 1 - 100lb Use Larger Tank Use Larger Tank

(See the parts list for your model of heater to get the specified regulator assembly.)

The propane (LP) gas tank must also be equipped with the following:

• A collar to protect the Propane gas valve.

• A shutoff valve terminating a Propane gas cylinder valve outlet as specified in the

American National Standards for Compressed Gas Cylinder Valve Outlets and Inlet

Connections.

• A safety relief valve having direct communications with the vapor space of the tank.

• An arrangement of vapor withdrawal.

The propane (LP) gas pressure regulator and hose assembly supplied with this heater must be used without alteration.

The hose assembly shall be visually inspected prior to each use of the heater. If it is evident that there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the heater being put into operation. The replacement hose assembly shall be that specified by the manufacturer. (See page 11, Part number 42)

Page 4

INSTALLATION TO THE PROPANE GAS TANK:

IMPORTANT: You must use a propane/LP gas supply cylinder that is compatible with the connection device provided with the hose and regulator.

1. Provide propane/LP supply system (see Propane/LP Supply, page 6).

2. Connect fuel gas fitting hose/regulator assembly to propane LP tank(s). Turn fuel fitting counterclockwise into threads on tank. Tighten firmly using a wrench. IMPORTANT: Position regulator so that hose leaving the regulator is in a horizontal position (see Figure 1)

3. Connect hose to heater inlet. Tighten firmly using a wrench. You must use the regulator supplied with heater.

4. Open propane/LP supply valve on propane/LP tank(s) slowly. NOTE: If not opened slowly, excess flow device in regulator may stop gas flow. If this happens, close propane/LP supply valve, wait one minute (or until you hear a click) and open again slowly.

5. Check all connections for leaks. Apply a 50/50 solution of liquid dish soap and water to gas joints.

Bubbles forming show a leak that must be corrected.

6. Close propane / LP supply valve before attempting to repair connection.

WARNING: Purging and filling of LP gas tanks must be performed by personnel who has been thoroughly trained in accepted LP gas industry procedures. Failure to follow these instructions may result in explosion, fire, severe personal injury, or death.

REFILLING THE PROPANE GAS TANK:

ALL NEW CYLINDERS MUST BE PURGED BEFORE THE FIRST FILLING.

• Turn heater gas valve knob and gas tank valve to OFF position.

• Propane tank valve equipped with the old style fitting has LEFT HANDED THREADS. Turn POL fitting CLOCKWISE to loosen. Protect POL fitting when disconnected from tank.

• Have tank filled by your local Propane gas supplier.

• Some propane tanks have a bleed-off valve. This valve should be inspected for leaks after each filling of the tank. Turn clockwise to close the valve.

• Fasten full Propane tank and connect POL fitting to tank valve by turning COUNTERCLOCK-

WISE.

• With heater gas valve knob still in the OFF position, turn ON tank valve and check for leaks with soap solution.

Page 5

Propane is safe to use when properly handled. Careless handling of the Propane gas tank could result in fire and/or an explosion. Therefore:

• Always keep tank/cylinder securely fastened in an upright position.

• Avoid tipping tank on its side when connected to a regulator since this may cause damage to diaphragm in regulator.

• Handle valves with care.

• Never connect an unregulated Propane tank to construction heater.

• Do not subject Propane tank to excessive heat.

• Tightly close the gas shutoff valve on the Propane tank after each use.

• The POL fitting must be protected when disconnected from the propane tank.

• Never store a Propane gas tank inside a building or in the vicinity of any gas burning appliance.

THE DISCONNECTED TANK MUST NEVER BE STORED IN A BUILDING, GARAGE OR

ANY OTHER ENCLOSED AREA.

LEAK CHECKING:

Check all gas connections with a soap solution to be sure they are tight and leak proof.

• The installation of your heater must meet all local codes and/or gas utility requirements or, in the absence of local codes, with the Storage and Handling of Liquefied Petroleum Gases,

ANSI/NFPA 58 and the Natural and Propane Installation Code, CSA B149.1.

• The minimum clearances to combustible construction shown above must be maintained at all times.

• The hose assembly should be visually inspected prior to each use of the heater. If it is evident that there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the heater being put into operation.

• The replacement hose assembly shall be that specified by the manufacturer (See page 11 for part numbers).

LIGHTING INSTRUCTIONS:

WARNING: Motor and fan must be running before lighting, during operation and shutdown, in order to prevent a flame-out condition which could result in personal injury or property damage.

1. Connect power cord to a properly grounded three (3) prong 120V, 60Hz, single phase receptacle.

2. Turn gas valve knob clockwise to OFF position.

3. Wait five (5) minutes to clear any gas. Then smell for gas, if you don't smell gas, go to next step.

4. Turn gas supply ON by turning Propane tank valve counterclockwise.

5. Push in and turn gas control knob counterclockwise to “LOW/IGN”. This will light the burner. If needed, keep pressing control knob until the burner lights and keep depressing and turning from

OFF to LOW/IGN on Piezo electric spark models. (“HIGH/IGN”: In case of RMC-FA40DLX)

6. Keep the valve knob depressed for at least 30 seconds after lighting the burner. After 30 seconds release valve knob.

7. If burner does not stay lit, repeat the lighting procedure.

8. When burner is lit, turn gas valve knob counterclockwise to desired setting. (All models, except

RMC-FA40DLX, RMC - 40 has only one heat setting)

Page 6

SHUTDOWN INSTRUCTIONS:

Shutoff Heater:

WARNING: Motor and fan must be running before lighting, during operation and at shutdown, in order to prevent a flame-out condition which could result in personal injury or property damage.

Turn gas valve knob clockwise to OFF position.

Turn gas supply OFF by turning Propane tank valve clockwise to close.

Disconnect the power cord once the heater has cooled to ambient temperature.

TEST FIRING HEATER:

Test fire your construction heater, following the lighting instructions applicable to the gas control system employed. Leak test all gas connections with soap solution. Soap bubbles indicate gas leakage. DO NOT use a match or flame to test for gas leaks.

STORAGE:

Never store a Propane gas tank inside a building or in the vicinity of any gas or oil burning appliance. When the Propane tank is not disconnected from the construction heater, the gas tank and heater must be stored outdoors in a well ventilated area, out of the reach of children. If for any reason the heater is to be stored indoors, the tank must be disconnected and stored outdoors in a well ventilated area out of reach of children, in accordance with the standard for the the Storage and Handling of Liquefied Petroleum Gases, ANSI / NFPA 58 and CSA B149.1, Natural Gas and

Propane Installation Code. The plastic tank valve plug supplied with your tank must be tightly installed when the tank is disconnected from the heater.

MAINTENANCE INSTRUCTIONS:

1. Turn unit off, allow heater to fully cool and disconnect propane hose before performing any

Maintenance functions.

2. Keep unit clean and keep the inside of the torpedo housing debris free.

3. Have unit checked by a qualified technician at least once a year, preferably prior to the heating season.

TROUBLESHOOTING:

PROBLEM

Fan does not turn when electrical connection is made.

POSSIBLE CAUSE

1. No electric power to heater.

Heater will not fire.

2. Fan blade contacts inside of heater housing.

3. Fan blade(s) bent

4. Fan motor defective.

1. No spark at ignitor.

2. Improper spark gap.

3. Bad electrode.

CORRECTIVE ACTION

1. Check current to electric outlet. If voltage is correct, check power cord and extension cord for cuts and extension cord for cuts and breaks.

2. Be sure that housing is not damaged.

Make sure there are no obstructions to the fan.

3. Straighten blade(s) to match others.

4. Replace motor.

1. Check ignitor wire. Re-attach or tighten if loose. Check Spark module. Replace if necessary.

2. Set gap to 0.16”

3. Replace Spark Plug.

Heater quits while running.

1. Internal temperature too high causing limit switch to shut down operation.

2. Damaged Control Valve.

3. Dust or debris build-up inside of heater.

1. If the heaters output is restricted, internal temperature becomes too high. Move heater away from any obstructions.

2. Replace Control Valve.

3.Clean inside of heater.

Always be sure to follow proper maintenance procedures, by cleaning the heater once per month during regular usage, and check spark gap at least once per season.

Page 7

PROPANE CONSTRUCTION HEATER ILLUSTRATED

40,000 BTU/Hr - 50,000 BTU/Hr

Page 8

ITEM

NO.

30

31

32

33

26

27

28

29

34

35

36

37

38

18

19

20

21

15

16

17

17-1

22

23

24

25

39

40

41

7

8

9

10

4

4-1

5

6

11

12

13

13-1

14

1

2

3

OUT SHELL

HANDELASSEMBLY

SCREW

MOTOR ASSEMBLY

FAN

SCREW

SUPPORT MOTOR

SUPPORT MOTOR SCREW

MOTOR BRACKET

MOTOR CONDENSER

SCREW

GUARD FAN

POWER CORD

PCB ASSEMBLY

SCREW

LEAD WIRE ASSEMBLY

CONNECTOR INLET

BASE LOWER

VALVE

VALVE KNOB

SCREW

BASE ASSEMBLY

SCREW

WING BOLT

SCREW

HEIGHT CONTROLLER

SHELL IN ASSEMBLY

FLAME HOLDER

NOZZLE

THERMAL SWITCH BRACKET

SCREW

SCREW

THERMAL SWITCH

NOZZLE NUT

THERMOCOUPLE

THERMOCOUPLE BRACKET

SCREW

SPARK PLUG

SPARK PLUG BRACKET

SCREW

TUBING ASSEMBLY

SCREW

SCREW

REGULATOR ASSEMBLY

ILLUSTRATED PARTS BREAKDOWN

DESCRIPTION QTY.

PART NUMBER

RMC-FA40DLX/

RMC-FA40A/RMC-FA50A

CFM40.01

CFM40.10

M5X10

CFM40.09-02

CFM40.05-01

ST3.9X8

CFM40.06-02

M6X15

CFM40.06-01

CFM50.09-03

M4X8

CFM40.08

CFM40.09-01A

3TH0001

ST4.2X10

CFM40.09-03.01A

CFM40.13

CFM40.02-03

CK-890SL-A1(A)

CFM40.11

ST3.9X8

CFM40.02

ST4.2X10

CFM40-M6X12

ST4.2X10

CFM40.02-04

CFM40.03

CFM40.03-02

CFM40.12-01

CFM40.07-02

ST4.2X10

ST2.9X6

CFM50.09-06

CFM80.00-07

1130/1395C-180

CFM40.07-01

ST4.2X10

CFM40.09-04

CFM80.00-04

ST4.2X10

CFM40.12

ST4.2X10

ST3.9X8

TYQ-9C

1

1

1

1

1

1

1

1

1

1

1

1

1

3

6

1

4

1

4

1

1

1

1

1

1

1

1

1

1

1

2

1

4

1

1

1

1

1

1

1

1

1

1

2

Page 9

REMARK

PROPANE CONSTRUCTION HEATER ILLUSTRATED

100,000 BTU/Hr - 150,000 BTU/Hr

Page 10

ITEM

NO.

ILLUSTRATED PARTS BREAKDOWN

DESCRIPTION

5

5-1

6

7

3

4

1

2

OUT SHELL

HANDELASSEMBLY

SCREW

NUT

MOTOR ASSEMBLY

MOTOR FAN

MOTOR SUPPORT

MOTOR SUPPORT SCREW

11

12

13

14

8

9

9-1

10

MOTOR BRACKET

MOTOR CONDENSER

SCREW

GUARD FAN

POWER CORD

19

20

21

22

23

15

16

17

18

SPARK MODULE

CIRCUIT BOARD ASSEMBLY

CIRCUIT SCREW

LEAD WIRE ASSEMBLY

VALVE

MPU LEAD WIRE ASSEMBLY

24

25

26

27

CONNECTOR INLET

VALVE KNOB

SCREW

BASE ASSEMBLY

SCREW

HEIGHT ADJUSTER KNOB

BASE LOWER

SCREW

HEIGHT CONTROLLER

28

29

COMBUSTION CHAMBER

FLAME HOLDER

29-1 SCREW

30 THERMAL SWITCH

33

34

35

36

31 THERMAL SWITCH BRACKET

31-1 SCREW

31-2 SCREW

32 THERMAL SWITCH CABLE

NOZZLE

NOZZLE NUT

THERMOCOUPLE

THERMOCOUPLE BRACKET

36-1 SCREW

37 SPARK PLUG

38

39

SPARK PLUG BRACKET

SCREW

40

41

42

TUBING ASSEMBLY

SCREW

REGULATOR ASSEMBLY

QTY.

1

11

1

1

1

1

1

1

1

1

1

1

1

2

1

3

1

1

1

6

1

1

1

4

1

1

1

6

1

1

1

1

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1A0093

2A0156

BT1406W

4A0229A

4TH0004

TBQ22362

TBQ1830V

4A0299

4A0233B

4A0207B

3A0207A

4A0260

PT2406W

4A0287B

4A0261

PT2406B

3A0222

BT1408W

5TH0002

3A0198B

3TH0001

BT1408W

4TPH013

DMV110PB

4A0304

4A0234

3D00279

BT1408W

1A0090

BT1408B

4TH0034

1A0092

BT1408B

3A0192A

PART NUMBER

RMC-FA100DLX/

RMC-FA100A

RMC-FA150DLX/

RMC-FA150A

1A0091A

3A0197

1A0091B

3A0197

PMF 4012Y

HOT04Y

PMF 4012Y

HOT04Y

2A0169B

3A0199B

3A0196

HBT 0620W

2A0157

7µF

BT1408W

2TH0009

3TPH013A

2A0169B

3A0199B

3A0196

HBT 0620W

2A0157

7µF

BT1408W

2TH0009

3TPH013A

1A0093

2A0155

BT1406W

4A0229A

4TH0004

TBQ22362

TBQ1830V

4A0299

4A0247

4A0235

3A0207A

4A0260

PT2406W

4A0287C

4A0261

PT2406B

3A0212

BT1408W

5TH0002

3A0198B

3TH0001

BT1408W

4TPH013

DMV110PC

4A0304

4A0234

3D00279

BT1408W

1A0090

BT1408B

4TH0034

1A0092

BT1408B

3A0192A

REMARK

Page 11

WIRING DIAGRAMS:

Page 12

WARRANTY :

SERVICE AND LIMITED WARRANTY

CFM Home Products warrants this product to be free from defects in materials and components for two (2) years from the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under warranty the Bill of Sale or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating condition and an allowance for labor when provided by a CFM Home Products Authorized Service Center.

Warranty part(s) MUST be obtained through authorized dealers of this product and/or CFM

Home Products who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS

THE SALE OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL

OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL

IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE TO TWO (2) YEARS FROM THE DATE OF FIRST

PURCHASE PRICE OF THE PRODUCT AND CFM HOME PRODUCTS SHALL NOT BE

LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL

OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

Contact CFM Home Products for consumer information, technical assistance and to obtain replacement parts. You will need to provide the following information when communicating with the help desk:

• Heater type and model number

• Serial Number

• Description of the part or problem.

CFM Home Products

2695 Meadowvale Blvd.

Mississauga, Ontario L5N 8A3 Canada

Tel 1-800-668-5323

advertisement

Related manuals

advertisement