Prompt Set Deluxe Spa Manual
110-120V 60Hz 1380W 12.5A
Prompt Set SPA - Home Basic JL017132NN
Prompt Set SPA - Deluxe JL017133NN
E
1
BS2-12-E
WARNING
When installing and using this electrical equipment, basic safety precautions
should always be followed; including the following:
IMPORT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
TABLE OF CONTENTS
1. Important Safety Guidelines………………………..…… P1-2
2. Specification and Part List….………………………..….. P2-3
3. Installation and Operation…………………………..…… P4-11
• 3.1 SPA Pool Set Up Instructions….……………….. … P4-7
• 3.2 SPA Pump Operation………….….…………….. … P8-10
• 3.3 Pool Water Drainage………….….………………... P11
• 3.4 Clean/Replace Filter Cartridge.………………….... P12
4. Maintenance SPA ……………………………………… P13
• 4.1 SPA water treatment………………………………... P13
• 4.2 Cleaning the SPA…………………………………... P14
• 4.3 Repair Patch instruction……………………………. P14
• 4.4 SPA Storage…………………………………............. P14
5. Trouble Shooting................................................................. P15-16
• 5.1 Error Code table.......................................................... P15
• 5.2 E5 error solution—Reset thermal cutout..................... P16
• 5.3 Other frequent problem solution................................. P16
6. Limited Warranty................................................................. P17-18
2
1.
The appliance should be supplied through a residual current device(RCD)
having a rated residual operating current not exceeding 30mA.
WARNING:
2.
WARNING: No part of the appliance is to be located above the bath during use.
3. WARNING: This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
4.
WARNING: TO AVOID THE ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS RAINING.
5 WARNING: Children should be supervised to ensure that they do not play with the appliance.
6. WARNING: If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
7.
To reduce the risk of electric shock, do not use extension cord to connect unit to
electric supply; provide a properly located outlet.
WARNING:
8.
WARNING: Make sure the home fixed connection box shall be more than 3.5m away from the pool.
9.
RISK OF ELECTRIC SHOCK. DO NOT BURY CORD. Locate cord to minimize
abuse from lawn mowers, hedge trimmers, and other equipment. To reduce the risk of electric shock, replace
damaged cord immediately.
WARNING:
10.
WARNING: Electric installations should fulfill the requirements of local standards.
11. WARNING: Parts containing live parts, except parts supplied with safety extra-low voltage not
exceeding 12 V, must be inaccessible to a person in the SPA pool..
12.
WARNING: parts incorporating electrical components, except remote control devices, must
1
WARNING: Do not switch on if there is any possibility that the water in the SPA is frozen.
14. DANGER: Risk of Electric Shock. .Install at least 5 feet (1.5 m) from all metal surfaces.
15. DANGER: Risk of Electric Shock. Do not permit any electric appliance, such as a light, telephone,
13.
radio, or television, within 5 feet (1.5 m) of a SPA.
of user or damage the SPA;
25.
NOTE: do not run the pump more than 8 hours per day after the temperature reaches to your set point.
SAVE THIS INSTRUCTION FOR FUTURE REFERENCE!
DANGER:
16.
Risk of Accidental Drowning. Extreme caution must be exercised to prevent
unauthorized access by children. To avoid accidents, ensure that children cannot use this SPA unless they are
supervised at all times.
DANGER:
18. CAUTION: For below mentioned situation, please always consult your doctor before
17.
a) The use of alcohol, drugs, or medication before or during SPA use may lead to
unconsciousness with the possibility of drowning.
b) Obese persons and persons with a history of heart disease, low or high blood pressure,
circulatory system problems, or diabetes should consult a physician before using a SPA.
c) Persons using medication should consult a physician before using a SPA since some
medication may induce drowsiness while other medication may affect heart rate, blood
pressure, and circulation.
d) Pregnant or possibly pregnant women should consult doctor before using SPA.
CAUTION:
20. CAUTION: The SPA should not be setup or left out in temperature lower than 10 ºC (50 ºF) .
21. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this
19.
+ Filter
JL017132NN
JL017133NN
110-120V 60Hz
110-120V 60Hz
1320W + 60W
1320W + 60W
appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that
is regularly switched on and off by the utility.
CAUTION:
22.
Check with a doctor before use if pregnant, diabetic in poor health, or under medical
care. Exit immediately if uncomfortable dizzy, or sleepy. SPA heat can cause hyperthermia and unconsciousness.
SPA heat in conjunction with alcohol, drugs, or medication can cause unconsciousness.
CAUTION: Do not use the SPA immediately following strenuous exercise.
24. CAUTION: Do not add chemical in the water freely, because chemical reaction may impact safety
23.
2
3
INSTALLATION INSTRUCTIONS
Note: Ensure to check all parts are present.
A-1˖Pool cover with foil and zipper
A-2˖ Deluxe Top lid
B ˖Pump
C˖ SPA pool
D-1˖Digital lock
D-2˖Digital lock on buckle
E˖Inflation hose
F˖Connection hose
G˖filter cartridge
H-1˖stopper cap
H-2˖PVC film
H-3˖Glue
H-4˖stopper
H-5˖ Manual
H-6˖Hose adapter
A-1
E
F
D-2
G
WARNING:
NOTE:
Please select a set-up site which strictly conforms to the above guidelines. Pools installed
on inadequately level surfaces may result in property damage or serious injury, which will
make the warranty invalid.
A-2
D-1
1.SITE SELECTION
IMPORTANT GUIDELINE:
1.1 Looking for a smooth, flat, level solid foundation to support the weight of SPA and water, plus user.
1.2 The pool must be accessible to an adequate drainage system for overflow water.
To reduce the risk of electric shock, do not use extension cord to connect unit to
electric supply; provide a properly located outlet.
C
B
SPA POOL SET UP INSTRUCTIONS
H-1
H-2
H-3
If you are installing the SPA outdoors, ensure there are no sharp objects that could damage
it and that the location is level so the SPA sits stably and properly.
Special requirements for indoor installation:
Caution: Non-slip floor surface is required around the SPA pool.
The pool must be accessible to an adequate drainage system for overflow water and drainage.
The SPA pool must be installed in ventilated area to minimize the humidity caused by hot
water. To avoid any furniture or articles damaged by moisture, please check before installation
and keep them away the area.
Special requirements for outdoor installation:
Ensure that the area is firm, flat and extremely level, with a grade not exceeding 3° of slope at any point in the set-up area.
Make sure that the area is completely free of sticks, stones, sharp objects or other foreign debris to damage the pool.
To prolong the product life of pool, do not expose the SPA pool to direct sunlight for long period.
We don’t recommend to use the SPA pool under 10℃(50℉). Heating rate may not satisfy you under too low temperature.
During filling, emptying or when in use, water may spill out of the SPA. Therefore the SPA should be installed near a
ground drain.
2.RCD TEST
Before using the pump to inflate the SPA, do RCD test on the plug of SPA pump:
H-4
4
H-5
H-6
WARNING:
WARNING: Before inserting the plug into a power outlet, make sure the current rate of the power
RISK OF ELECTRIC SHOCK. The RCD plug must be tested before each use.
Do not use if RCD test fails.
outlet and the fixed wiring are suitable for the pump. Contact a qualified electrician if you cannot verify
5
2
1
4
3
Insert the plug into the
Press “ RESET” button,
Then,
press
RCD power outlet.
check if the indicator
button,
check
“TEST”
light turns red
indicator light is off
if
the
80% capacity.
• Adjust the pool cover and make sure that each adapter on the pool wall is placed on the correct
position.
Press “RESET” button
again, check
if
the
indicator light turns
red again.
If all above steps are successful, the SPA pump is ready for use.
3. ASSEMBLY SPA POOL
Warning:
The maximum pressure for all
air chambers should be 5.0kpa.
a)
c)
b)
P-1
Spread out the SPA pool make
Connect the black inflation
sure all adapters are on right
As previously outlined, do RCD
hose to black adapter on the
position of pool cover
test on the plug of SPA pump.
pump
Press the massage button to
inflate the SPA pool.
TIP: How to use the safety valve
a) Insert black one-way intake
b)
c) Fasten the small top cover of the valve.
d)
a)
b)
• How to change the combination of digital lock: (Refer to P-1)
Original code combination is set as 000, which is on the red line side.
Push release button on the upside left, when the digital is placed on the set combination. The
lock will be released.
Push down the black button on the right side, then set your desired combination by moving
the number wheel. Release the black button, The new code combination is ready for use.
Please do not forget your new code combination.
c)
d)
WARNING: Do not move the number wheels while the digital lock is open. Or you will change the
combination you just set. This will unable the digital lock.
FOR JL017133NN
(5) How to use the combination of digital lock on buckles: (Refer to P-2)
Original combination is set as 00
Lock: Fasten all buckles, move the number wheel to lock buckles.
Unlock: Move the number wheel to 00, press the buckle to release the digital lock.
The code combination can not be changed.
a)
6
P-2
heating and bubbling adapters on the pool.
7
a)-1
d)-1
SPA PUMP OPERATION INSTRUCTIONS
d)-2
a)-2
1. RELEASE THE AIR INSIDE THE PUMP
WARNING: Never run the pump idly. Release the air inside the pump is the key step to ensure the
pump running normally
WARNING: The water in the SPA pool must reach minimum water level printed on pool inner wall.
b)
Open the cartridge lid by counter-clockwise. Then put the new filter cartridge into the pump.
Then screw the pump top lid clockwisely. (Refer to below illustration)
1) Unscrew the air purge valve counter-clockwise until the water is emerged.
2) Then close the air purge valve by clockwise turn.
3) Dry any excessive water on the pump body.
1)
2)
3)
2. FUNCTIONS OF SPA PUMP
c)
water level printed on pool inner wall.
c-1)
c-2)
d)
WARNING:
WARNING: Children is always attracted by water; Always lock the top lid after each use.
WARNING: Adult supervision is required for children around the SPA pool at all time.
d) Before heating, place and lock the top lid to the SPA pool by using the digital lock on the top lid.
The cover is not a substitute for adult supervision;
8
1)
LED Display: Once powered-up, the LED displays the current water temperature
automatically.
Note: If pressing is valid, you can hear buzzer and relative indicator light will turn on .
2)
Temperature Adjustment buttons: Increase
Decrease
set the desired temperature. The value will increase or decrease 1°C by once. If you hold the
button for 2 seconds, the values will rapidly increase
Temperature adjustment ranges:
• Celsius mode: 30℃- 38℃
9
• Fahrenheit mode: 86℉-100.4℉
+
at same time and hold 3 seconds. Please lock the
To lock the control panel, press
control panel during your leave to avoid others change your set model. Unlock the control panel
by pressing
3)
+
at same time and hold 3seconds again.
“Temperature Mode” button: Press the button to exchange Celsius mode and
Fahrenheit mode
“Bubble Massage” button: Activates bubble massage system
Press this button to activate the massage system, the green indicator light turns on. It can be
turned off by pressing it again.
Note:
a) The massage system will stop automatically after 30 minutes of operation. Re-activate the
massage function by pressing the massage button again.
4)
b) When
is on, pressing
light will turn off and massage indicator light turn on. If press the
working, pressing
are shut down, massage system will be activated. If press
re-start.
Press
1)
2)
3)
5) We recommend to use “Bubble function” to blow out water from the SPA pipes.
6)
dry the pump completely by draining all water from pump body and pipes.
6)-2
may shut down heating and
When
6)
can not activate them.
3 Drainage
1) Turn off all the buttons on the control panel and unplug the appliance.
2) Connect drain pipe on the bottom of SPA with a long hose, place another end of hose to
drainage area. (picture 1)
3) Open the drain valve on the bottom of SPA pool. (picture2)
4) Have the SPA tilted to completely drain all water in the SPA pool. (picture 3)
6)-1
: Activates Filter system
Note:
or
again, the massage
c) Heating and Massage function can not be activated at same time. When heating system is
5)
When bubble function is on, pressing
7)
: Activates Heating and Filtering system at the same time
6-16
7)-1
-2
7)-2
to activates Heating and Filtering system at the same time: the green indicator light of
The pump does not stop heating until the current water temperature reaches the set temperature;
and the heating system will restart after the current water temperature drops 2℃ below the set
temperature automatically.
Heating Rate : approximately 1~1.2℃/hour. Max. heat temperature:38℃(100.4 ℉)
NOTE:
This is normal!
10
11
8) Refer to 7-1 /7-2 we recommed to use “Bubble function” to blow out water from pump. Then
unplug the pump and tight the drain valve.
7-1
8)-1
7-2
8)-2
89)
MAINTENANCE SPA
1. SPA water treatment
Note: Pool quality can harm your health. We recommend you to maintain SPA water as below:
2) Change water every 14 days and use appropriate pool chemicals after each usage.
3) The application of chemicals will stop the growth of harmful bacteria or algae in your pool,
supply retailer for more information about chemical maintenance. Pay close attention to the
chemical manufacturer’s instructions. SPA damage resulting from misuse of chemicals and
mismanagement of SPA water is not covered by the warranty.
9) Clean and dry the pool and pump.
4. CLEANING/REPLACE FILTER CARTRIDGE
WARNING: RISK OF ELECTRIC SHOCK. Unplug the pump before beginning SPA maintenance.
Note:
Note:
every day and replaced 3 days depending on use.
1) Unplug the pump.
2) Open the air release valve by turning it counterclockwise.
3) Insert the stopper caps onto the inlet and outlet on the pool inner wall.
4)
5)
6)
7)
correct position.
8) Close the lid by turning clockwise.
9)
into pump.
10) Repeat previously outlined steps: Do RCD test, release air in the pump, and operate pump as
your need.
12
Do not use the SPA during disinfecting!
WARNING:
Do not use the chlorine chemical, it can corrupt the temperature system.
Pay close attention to the chemical manufacturer’s instructions!
a) Water Balance
We recommend maintain your water balance as below:
PH value: 6.5 - 8.5; Total alkalinity: 80 - 120ppm; Free chlorine: 3ppm - 5ppm
Purchase a test kit to test your water chemistry Value before each use of the SPA, at least once
per week. Low PH value will damage the pool and the pump. Damage resulting from chemical
imbalance is not covered by the warranty.
b)Water Sanitation
The SPA owner should do water sanitation regularly (daily, if necessary). The sanitizer will
or introduced during use of the SPA.
Pool chemical maintenance
We suggest to use BROMINE tablet with our chemical floater to disinfect the pool’s water.
1)
20 pieces)
2)
3) We suggest you to activate the bubble function while water is being disinfection in the pool, it
is useful to let water circulate and disinfect the microorganism completely. Please see below
illustration:
1)
2)
13
2. Cleaning the SPA
Clean the SPA pool with soap and water, then rinse. Leave it in shady and cool place for airing.
NOTE: DO NOT use hard brushes or abrasive cleaners. Do not use the alkali or acid
detergent to clean product!
To avoid E7 trouble, please clean the insdie water mouth(inlet and outlet) of the SPA pool to
wipe off any dirts before and after each use!
3. REPAIRS (Little holes or puncture can be repaired with the repair kit come along with
the SPA)
1. Find the leak.
2. Thoroughly clean the area surrounding the leak to remove any dirt or grime.
3. Cut a piece of repair material in round shape, which should be larger than the damaged area.
4. Using a piece of the repair kit, trace outline of the patch lightly.
5. Apply adhesive to the underneath side of the patch and around the area to be repaired. Coat the
affected are lightly but completely with glue.
6.
7. Allow 12 hours for repair to dry. After patch has dried, apply glue around the edges for a
complete seal (dry 4 hours)
4. SPA storage
Completely drain all water from the SPA pool and pump. Remove the filter cartridge. It is
recommended that you store the SPA in its original package in a warm dry place.
NOTE: Do not expose the SPA pool to subzero temperatures or under sunlight directly for
long time because it will shorten the using-life of product. Improper winterization of you
SPA may void your warranty
TROUBLE SHOOTING
Jilong aims to provide trouble-free SPA. If you experience any problem, do not hesitate to contact
your local dealer or our after sales service.
Here are some useful tips to help you to diagnose and rectify common sources of trouble.
1) Error Code: When LED displays the below error code, please check the below reference list.
System protection
Code
E1
E2
CAUSE
Temperature control sensor
fault
Temperature protection sensor
fault
SOLUTION
Professionals need to maintain, please contact us or our after sales
service agent!
Professionals need to maintain, please contact us or our after sales
service agent!
E3
High temperature protection
Cut off the power supply. After some hours, you can operate the
pump as soon as the water temperature is between 20℃ to 38℃.
E4
Low temperature protection
Cut off the power supply. Check the water temperature is in
between 20℃ to 38℃. You can operate the pump as soon as the
water temperature is between 20℃ to 38℃.
Without heating Function
Cut off the power supply, and then checking as below:
A) Checking the filter cartridge, if it is dirty, please replace it
immediately. And then bleeding the air purge valve after
assembling the filter cartridge upper lid.
B) Checking the non-self-resetting thermal, if it is cutoff, please
reset it as above page of d) reset of non-self-resetting thermal
cutout.
C) Checking the pool cover is closed or not.
D) Checking the pool’s actual water capacity, if the operation
water line is nearby the standard water level line.
E) The pool’s inlet and outlet jam or not.
E5
2) E5 error solution-Reset thermal cutout
14
15
(1) Cutoff power of pump
(2) Insert the stopper caps onto the inlet and outlet on the pool inner wall
(3) Disassemble pump, turn over the pump.
3
2
1
RECYCLING
Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems
(4) Locate the small hole marked “reset” on the bottom of pump. Then, inset a small stick (It
should be less than Ø0.9cm, length is longer than 10cm) into the hole, press down, you can
hear “ping”, the reset is successful.
(5) Then, connect pump with pool again. Take off the stopper on the inner pool and repeat the
previous outlined steps to use your SPA.
Tempreature increasing rate
Outside temperature
Spa max water temperature
54F (12.2C)
100F (37.8C)
52F (11.1C)
99F (37.2C)
50F (10C)
98F (36.7C)
48F (8.9C)
97F (36.1C)
46F (7.8C)
96F (35.6C)
44F (6.7C)
95F (35C)
42F (5.6C)
94F (34.4C)
leak into the groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back
your old appliance for disposals at least free of charge.
This product bears the selective sorting symbol for waste electrical and electronic equipment
(WEEE). This means that this product must be handled pursuant to European Directive 2002/96/
EC in order to be recycled or dismantled to minimize its impact on the environment. For further
information, please contact your local or regional authorities. Electronic products not included in
the selective sorting process are potentially dangerous for the environment and human heath due
to the presence of hazardous substances.
During start up and initial assembly, depending on the outside temperature, it will take up to 20 hours to heat up your spa
to a comfortable temperature. Spa cannot be used in negative outside temperature.
Heating rate:1-1.2C per hour.
FREQUENT PROBLEMS SOLUTION
TROUBLE SHOOTING
Jilong strives to provide the best trouble-free spa on the market. If you experience any problem whatsoever do not
hesitate to contact your authorized dealer or us.
Here are some helpful tips to help you to diagnose and rectify common sources of trouble.
Problems
Probable Causes
Control box does not
� Power failure
� Check power source
operate
� RCD tripped
� Reset RCD/check if the home fixed wiring too
� RCD broken
Solutions
thin to afford 1460W
� Call for service if it does not reset
Control box does not heat
� Temperature set too low
properly
� Dirty Filter Cartridge
� Clean/replace the filter cartridge in time
� Improper water levels
� Add water to specified levels
� Set to a higher temperature
� Heating element failed
� Call for service
Bubble massage system
� Pump is too hot
� Cut off the circuit breaker. After the pump has
does not work
� 30-minute auto shut off
feature activated
� Something is wrong with
the control box
Water filtration not working
cooled, switch on the circuit breaker to
activate.
� Press the bubble button to reactivate
� Call for service if it does not reset
� Dirty filter cartridge
� Clean/replace the filter cartridge in time
� Something is wrong with
� Call for service if it does not reset
the control box
Spa leakage
� Spa is torn or punctured
� Use provided repair patch
Water not clean
� Insufficient filtering time
� Increase filtration time
� Dirty filter cartridge
� Clean/replace the filter cartridge
� Improper water
� Refer to the chemical manufacture’s
maintenance
16
instructions
17
LIMITED WARRANTY
ATTENTION CUSTOMER - Please read this statement carefully and keeps your original store receipt along
with this w arranty c ertificate all the time. Your receipt i s required as p roof of purchase and t o verify t he
length of your pool ownership.
Please register warranty within 30 days of purchase on www.jilong.com in order to validate your warranty.
We warrant all components contained in this SPA Pool against defects in materials and
workmanship under normal use and service. This warranty is subject to the obligations,
limitations, and exclusions listed below:
1. Extent of warranty
The warranty period commences on the original purchase date for the original owner only
A) 6 months warranty on tub; B) 12 months for electric parts.
2. If any of the components have been consumer-replaced, damaged, or misused, the
corresponding warranty on those components is invalidated. In this situation, you will be
advised of the cost of replacement parts and processing instructions.
or replace at its option under warranty provided proper proof of purchase is presented.
4. This limited warranty is not valid if the pool is used for commercial purposes, or if the damage
is caused by an accident, an act of God, consumer misuse, neglect or abuse, vandalism,
improper use of chemicals, exposure to extreme weather conditions or negligence during pool
set up or disassembly.
We can not be held responsible for the cost of installation (including water), labor, or
transportation expenses incurred due to the replacement of defective parts. This limited
warranty, furthermore, does not cover any unauthorized alterations to the pool system.
18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising