Makita 4331DWD Instruction manual

Cordless

Jig

Saw

MODEL 4331 DZ MODEL 4333DZ

MODEL 4331 DWD MODEL 4333DWD

INSTRUCTION MANUAL

Model

4331D

Battery

Voltage

12.0 v

Length of stroke Wood

Max. cuning capacities

Mild Steel Aluminum

~

""

(1")

(2.114")

4333D 14.4 V

Battery Cartridge 1234 IModel DC1411 High Capacity Battery Charger

Voltaae

12.0 v

I

Input

I

A.C. only 50 Hz - 60 Hz

I

OUtDUt

D.C. 7.2 V - 14.4 V

Strokes per minute

500-2,800

I

Overall length

2~~~~

Charging time

60 min.

Net weight

2.6 kg

(5.7 Ibs)

2.9 kg f f i 3 Ihsl

Voltage Input output Charging time

* Manufacturer reserves the right to change specifications without notice.

* Note: Specifications may differ from country to country.

WARNING: For your personal safety. READ and UNDERSTAND before using.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

2

GENERAL SAFETY RULES

(For All Battery Operated Tools)

WARNING! Read

and

understand all instructions. Failure to follow all instructions listed below,

may

result

in

electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used w i t h another battery.

Use battery operated tool only with specifically designated battery pack. Use of any other batteries may create a risk of fire.

Personal Safety

Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.

Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool w i t h the switch on invites accidents.

Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use

and

Care

Use clamps or other practical way t o secure and support the workpiece t o a stable platform. Holding the work by hand or against your body is unstable and may lead t o loss of control.

Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer a t the rate for which it is designed.

* D o

not use tool i f switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect battery pack from tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make

a

connection from one terminal t o another. Shorting the battery terminals together may cause sparks, burns, or a fire.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. I f damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool.

Service

Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure t o follow Maintenance Instructions may create a risk of shock or injury.

3

Specific Safety Rules

1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator.

2. Be aware that this tool is always in an operating condition because it does not have t o be plugged into an electrical outlet. fore operation.

4. Do not cut hollow pipe.

5. Do not cut oversize workpiece.

6. Check for the proper clearance beneath the workpiece before cutting so that the blade will not strike the floor, workbench, etc.

7. Hold the tool firmly.

8. Check the blade is not contacting the workpiece before the switch is turned on.

9. Keep hands away from moving parts. be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL!

Hold the tool only by the plastic handle t o prevent electric shock if you cut through a "live" wire.

11. Do not leave the tool running. Operate the tool only when hand-held.

12. Always switch off and wait for the blade t o come t o a complete stop before removing the blade from the workpiece.

13. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

4

SYMBOLS

Listed below are symbols commonly used on tools. v

................................... volts

- direct current n, ................................... no load speed

...

................................... revolutions or reciprocation per minute

5

6

ADDITIONAL SAFETY RULES

FOR CHARGER

&

BATTERY CARTRIDGE

1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF).

2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. or clog the charger vents.

4. Always cover the battery terminals w i t h the battery cover when the battery cartridge is not used.

5. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

1 Do not touch the terminals with any conductive material.

(2) Avoid storing battery cartridge in a container w i t h other metal objects such as nails, coins, etc.

6. Do not store the tool and Battery Cartridge in locations where the temperature may reach or exceed 5OoC (122OF).

7. Do not incinerate the Battery Cartridge even i f it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

SAVE THESE INSTRUCTIONS.

IMPORTANT SAFETY INSTRUCTIONS

FOR CHARGER

&

BATTERY CARTRIDGE

1.

SAVE THESE INSTRUCTIONS

-

This manual contains important safety and operating instructions for battery charger. on (1) battery charger, (2) burst causing personal injury and damage. manufacturer may result in a risk of fire, electric shock, or injury t o persons. cord when disconnecting charger.

7. so that it will not be stepped on, tripped over, or otherwise subjected t o damage or stress. improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size, and shape as those of plug on charger; b. That extension cord is properly wired and in good electrical condition; and c. That wire size is at least as large as the one specified i n the table below.

TABLE 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

Length of Cord (Feet)

AWG Size of Cord

25 50 100 150

18 18 18 16

9.

IO.

1 1 .

12.

FUNCTIONAL DESCRIPTION

Selecting the cutting action

This tool can be operated with an orbital or a straight line cutting action. To change the cutting action, just turn the lever to the desired cutting action position. Refer to the table below to help determine the appropriate cutting action.

Position Cutting action Applications

0 Straight line cutting action

For cutting mild steel, stainless steel and plastics.

For clean cuts in wood and plywood.

I

I

I

Small orbit cutting action

I

For cutting mild steel, aluminum and hard wood.

I

II Medium Orbit cutting action

For cutting wood and plywood.

For fast cutting in aluminum and mild steel.

~

I

111

1

Large orbit cutting action

I

For fast cutting in wood and plywood.

~

~ ~ ~ ~

~

I

Installing or removing battery cartridge

Always switch off the tool before insertion or removal of the battery cartridge.

.To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.

To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

8

Charging

Your new battery cartridge is not charged. You will need t o charge it before use. Use the high capacity battery charger Model DC1411 to charge the battery cart ridge.

Plug the high capacity battery charger into the proper A.C. voltage source. The charging light will flash in green color.

Insert the battery cartridge so that the

Charging light plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the high capacity battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor.

When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging light will remain lit steadily during charging. When the charging light color changes from red to green, the charging cycle is complete. The charging time is approximately one hour.

If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its "trickle charge (maintenance charge)" mode which will last approximately 24 hours.

After charging, unplug the charger from the power source.

CAUTION:

The high capacity battery charger Model DC1411 is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's batteries.

When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times.

If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash a red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the battery cartridge from the high capacity battery charger.

If the charging light flashes alternately in green and red color, a problem exists and charging is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.

9

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the charger will switch into its "trickle charge (maintenance charge)" mode and keep the battery cartridge fresh and fully charged.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged.

Always stop tool operation and charge the battery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F).

Let a hot battery cartridge cool down before charging it.

Switch action

CAUTION:

Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Pulling the trigger hard when the lock off button is not pressed causes switch damage.

To start the tool, simply push the lock off button then pull the trigger. Release the trigger to stop.

Speed adjusting dial

The tool speed can be adjusted and maintained between 500 and 2,800 strokes per minute by turning the adjusting dial. The dial is marked 1

(lowest speed) t o 5 (full speed).

I

Speed adjusting dial

L o c k 4 button

Refer to the table at right t o Select the proper speed for the workpiece t o be cut.

However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you t o cut workpieces faster but the service life of the blade will be

Workpiece t o b e cut

W o o d

M i l d steel

Stainless steel

A l u m i n u m

Plastics

N u m b e r o n adjusting dial

3 - 5

3 - 5

3 - 4

2 - 3

1 - 4

CAUTION:

Adjust the speed adjusting dial only within the range of numbers 1 through 5. Do not force the dial beyond this range or damage to the tool may result.

10

Anti-splintering device

To reduce the potential for workpiece surface splintering, the anti-splintering device can be used. Fit it into the base from below so that it surrounds the sides of the blade.

Plastic base plate (optional accessory)

Use the plastic base plate when cutting decorative veneers, plastics, etc. It protects sensitive or delicate surfaces from damage.

To replace the base plate, remove the four screws with the hex wrench.

Guide rule (rip fence; optional accessory)

When cutting widths of under 150 mm

(5-29/32”) repeatedly, use of the guide rule will assure fast, clean, straight cuts. To install it, loosen the bolt on the front of the base. Slip in the guide rule and secure the bolt.

I

I

I

-

11

Threaded knob c---

Circular guide (optional accessory)

Use of the circular guide insures clean, smooth cutting of circles under 200 mm center hole and secure it with the threaded knob. Move the base of the tool fully forward. Then install the circular guide on the base in the same manner, as the guide rule

(rip fence).

Plastic

Cover and

Vacuum

head (optional accessory)

The vacuum head is recommended to perform clean cutting operations. Install the plastic cover on the tool by fitting it into the notches in the tool.

Fit into notches

Base

12

To attach the vacuum head on the tool, insert the hooks of the vacuum head into the holes in the base. The vacuum head can be installed on either left or right side of the base.

Then connect a Makita vacuum cleaner to the vacuum head.

.,a

Base

1

ASSEMBLY

Installing or removing the saw blade

CAUTION:

Always be sure that the tool is switched off and battery removed before installing or removing the blade.

To install the blade, loosen the screw on the blade holder.

Loosen

With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits properly in the groove of the roller. Then firmly tighten the screw to secure the blade. screw

Hex wrench

I

CAUTION:

Always secure the blade firmly. Insufficient securing of the blade may cause blade breakage or serious injury.

Always clean out the blade holder before installing the blade. Chips or foreign matter on the blade holder may cause insufficient securing of the blade.

Use a lubricant or cutting oil between the blade and roller when cutting iron or composi- tion board, etc. Failure to do so will shorten the service life of your blade and roller or lead to potentially dangerous blade breakage.

13

Installing the universal shank jig saw blade

CAUTION:

Always be sure that the tool is switched off and battew removed before installing removing the blade.

If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.35 mm

( 1 /4").

Insert the blade into the blade holder as far as it will go. Make sure that the end of the blade shank reaches the bottom of the inner slit and tighten the bolt securely with the hex wrench.

The end of the blade shank should reach the

14

OPERATION

Cutting operation

CAUTION:

Check carefully that the blade is adequately secured in position before inserting the battery into the tool

Turn the tool on without the blade making any contact. Rest the base flat on the workpiece and gently move the tool forward along the previously marked cutting line.

I - I

Base

Cutting line

I

CAUTIO N :

*Always hold the tool with the base flush with the workpiece. Failure to do so may cause a slanted cutting surface and blade breakage.

*Advance the tool very slowly when cutting curves or scrolling. Forcing the tool may cause a slanted cutting surface and blade breakage.

Bevel cutting

CAUTION:

Always remove the battery from the tool before making any adjustments

With the base tilted, you can make bevel cuts at any angle between 0" and 45" (left or right). Loosen the bolt on the bottom of the tool. Move the base so that the bolt is positioned in the center of the cross-shaped slot in the base.

I

I

15

- is obtained. The edge of the motor housing indicates the bevel angle by graduations.

Then tighten the bolt to secure the base.

I

F , g e , o f motor housing

,

Graduations

I I

Base

Flush cutting

Loosen the bolt on the bottom of the tool and slide the base all the way back. Then tighten the bolt to secure the base.

cutouts

Cutouts can be made with either of two methods

A

or B.

A)

Boring a starting hole: For internal cutouts without lead-in cut from an edge, pre-drill a starting hole more than

12 mm (15/32") in diameter. Insert the blade into this hole and hold the tool firmly against the workpiece to start your cut.

16

B)

Plunge cutting: You need not bore a starting hole or make a lead-in cut if you carefully do as follows.

1) Tilt the tool up on the front edge of the base, with the blade point positioned just above the workpiece surface.

2) Apply firm pressure to the tool so that the front edge of the base will not move when you switch on the tool and gently lower the back end of the tool slowly.

3) As the blade slices into the workpiece, slowly lower the base of the tool down onto the workpiece surface.

4) Complete the cut in the normal manner.

Finishing edges

To trim edges or make slight dimensional adjustments, run the blade lightly along the cut edges.

Metal cutting

Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant blade wear. The underside of the workpiece can be greased instead of using a coolant.

MAINTENANCE

CAUTl

ON

Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.

Replacing carbon brushes

Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes.

L

/ \r

Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

Recycling the Battery

The

only

way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal.

I

Ni-Cd

To recycle the battery:

1 . Remove the battery from the tool.

2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or

Distributor that has been designated as a Makita battery recycling location.

Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under

"Tools-Electric' !

18

ACCESSORIES

CAUTION:

These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons.

The accessories or attachments should be used only in the proper and intended manner.

An exception: Universal shank jig saw blades with a thickness of 1 m m

-

1.25 m m (1/32" - 3/64") and a length of 58 m m - 82 m m (2-9/32"

-

3-7/32").

Plastic base plate

Part No. 413068-1

Anti-splintering device

Part No. 41 5524-7

High Capacity Battery Charger

Model DC1411

Hex wrench 3

Part No. 783201-2 r

Plastic cover

Part No. 415887-1 P

Guide rule

For 4331D

Battery cartridge 1222



For 4333D




Part No. 1641 13-2

Circular guide assembly

Part No. 123030-5

Hose 19-2.5

Part No.192108-5

Battery cover

Vacuum head

Part No. 192547-9

No. 59

1

I

Jia saw blade (Packed 5 each)

Blade :4:

I

I

Part No.

I

;;;;92::;

I

Teeth per

1 inch

2

I

Effective cutting blade length

65 mm (2-1/2")

80 mm (3-1/8')

I

1

7924306 80 mm (3-1/8")

I type

I

Part No.

I

Teeth per Effective cutting inch

I blade length

I

No.

8-18 792470-4 14 45 mm l1-3/4")

No, 8-19 792471-2 12 65 mm (2-1/2")

NO. 792529-7 80 mm (3-1/8")

No. B-11 792463-1 9 75" (3") NO.

8-23 7924746 14 50 mm 12")

I

No. 8-12

I

792464-9

I

6

1

80" (3-1B")

NO. 8-13

I

792465-7

No, 8-14

I

No. 8-24 792475-4 32 50 mm (2")

I

8

I

80 mm (3-1/8") No.

8-25 792476-2 9 75 mm (3")

I

792466-5

I

18

I

50" (2")

I

No. 8-26

I

7924774

I

9

1

70 mm (2-3/4")

I

I

No. 8-15

I

792467-3

I

12

I

50 mm (2")

I

I

No. 8-16

I

792468-1

1

6

I

80" (3-1/8")

I

I

No. 8-17

I

792469-9

I

6

I

70 mm (2-3/4")

No. 8-27

No. BR-13

792478-8

792727-3

24

9

50 mm (2")

64 mm (2-1/2")

(Note)

Refer to the next page for "Application" of each blade.

No. 8-21 792472-9 12 75 mm (3")

I

No. 8-22 1792473-8

I

24

I

50" (2")

I

19

20

Jig saw blade

I

Blade Type

No. 51

Wood & Dlvwood

1

-

No' 58

No' 59

No,

I

Plastics I

1.5 - 3 mm thick

11/16, - 1/8") ti

I

I

4

- 60 mm thick

15/32"

15/32''

-

-

2-3/8")

4 - 30 mm thick

1-1/8")

I

I

4

- 60 mm thick

15/32" -

2-3/8")

4 - 30 mm thick

15/32'' - 1-1B') I

3

-

60 mm thick

(1/8" -2-3/8")

I

3 - mm thick

(1/8" - 2-3B')

Aluminum

1

-

6 mm thick

13/64'' - 1/4")

-

-

Mild Steel Feature

1 - 3 mm thick Also ideal for cutting

13/64" - 1B") stainless steel.

I

-

I

For fast cutting.

I

-

I

For fast finish work

- - For fast finish work, especially in plywood.

-

-

For fast finish work

-

For fast finish work. -

~~

NO,

No

No, B-16

No.

No,

-

For roughingin work.

1

2

-

30 mm thick ti

(5/64" 1-1B'I

I

I

3

-

30 mm thick

(1/8"

5 -

- 1-1B')

60 mm thick l13/64" - 2-3/8"1

I

3

-

30 mm thick

(1/8"- 1-1@")

5 - 60 mm thick

-

1

2

-

30 mm thick

(5/64"

-

1-1/8")

I

(13/64"

-

2-3jE")

I

I

(13/64" - 2-3B'lS

-

I

-

I

For fast cutting.

5

-

60 mm thick 5

-

60 mm thick

(13/64"

- 2-3/8")

-

I

-

I

Ideal for scroll cutting.

I

'2

-

30 mm thick

I

2

-

30 mm thick

( 5 W '

-

1-1B'I (5/64"

-

1-1B')

I I

Ideal for cutting in thin materials.

1 1

Ideal for cutting in thin materials.

- -

Ideal for scroll cutting.

No,

NO. 6-21

3 - 30 mm thick ll/8" - 1-1/8"1

I

-

3

-

30 mm thick ti

11B' - 1-1/8")

I

3 - 5 5 m m t h i c k H

1

1.5-3mmthickH

(1/16"- 1B")

-

3

-

10 mm thick

11B'

-

3 B ' )

-

-

Cuts on down stroke.

Splinter-free on finish side.

For finish work, especially in plastics.

No. 6-22

N08-231

No. 6-24

No,

No.

No. 6-27

I

-

-

I

I

3

-

55 mm thick ti

I

3

-

55 mm thick ti

(1/8" - 2-1/8") (l/V -

2-1/8")

I

3

-

55 mm thick ti

1

3

-

55 mm thick

(1/8"

-

2-1B') (l/8"

-

2-1/8")

I

-

1

1.5-3mmthickH

(1/16'

-

1")

1

- 6 mm

(3/64" thick

- 1/4"1

I

3

-

6 mm thick

( l / 8 " - 1/4")

3

-

10 mm thick

( 1 B '

-

3 B ' l

0.5 - 3 mm thick

11/64'' - 1 ~ ' )

I

1

-

3 mm thick

(3/64"

Also ideal for cutting

- 1B") stainless steel. 1

3 - 6 mm thick

I

Also ideal for cutting

( 1 B '

-

1/47

0.5

-

2

11/61" thick

I stainless steel.

Also ideal for cutting stainless steel.

3

3

- 30 mni thick

11/8" - 1-1/8"1 t

3 - 10 mm thick

11/23'' - 3 B ' l

- 30 mm thick 3

-

10 mm thick

(1B"

-

1-1iE")

1

(1B" - 3 B ' )

1

I

Ideal for cutting thick materials. for scroll

1

- 6 mm thick

(3/64"

-

1/4,1

I l&jm?_",',!$p

I

Ideal for scroll cutting

CORDLESS JIG SAW

Model 4331D, 4333D

Nav-l9-'98 US

\

B

\

55

56

58

Note: The switch and other part configurations may differ from country to country.

21

MODEL 43331)

ITEM NO.

USED DESCRIPTION

ITEM

NO,

NO.

DESCRIPTION

19

20

21

22

23

24

25

26

27

28

29

30

31

~~

32

7

8

9

10

11

12

13

14

15

16

17

18

4

5

6

1

2

3

1

1

1

4

1

1

1

1

1

1

1

6

1

1

1

1

1

1

1

1

2

1

1

1

1

1

2

1

1

2

1

1

Switch Button

Compression Spring 4

Housing Set lWith Item 51)

Tapping Screw 4x18

Tapping Screw 4x30

Pan Head Screw M4x25

Switch

Switch Lever

Battery Holder

Holder

Gear Housing Cover Complete

Taping Screw 4x18

PI" 4


Holder

Stop Ring E - 3

Slider

Countersunk Head Screw M4x10

Thrust Plate

Retainer Complete

Name Plate

Rod

Hex Socket Screw M6x8

Slide Plate

Packing

Retaining Ring S

~

8

Needle Bearing 607

Hex Socket Head Bolt M4x16

Crank Complete

Flat Washer 26

Flat Washer 6

Balance Plate

Note The switch and other pan specifications may differ from country to country

51

52

53

54

55

56

51

44

45

46

4 1

48

49

50

58

59

60

61

62

63

64

33

34

35

36

37

38

39

40

41

42

43

1

4

1

1

1

1

1

1

1

1

1

1

3

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

Pin 6

Balance Plate

Flat Washer 6

Flat Washei 6

Pin 6

Push Plate

Flat Washer 26

Needle Bearing 810

PI" 5

Helical Gear 51

Needle Bearing 810

Flat Washer 8

Pin 8

Tapping Screw ST 4x8

Motoi Bracket

Countersunk Head Screw M4x10

DC Motor (With Spur Gear)

Housing Set (With Item 31

Lever 17


Steel Ball 4

Stop Ring (EXTI E - 5

Base

Clamp Plate

Base Plate

Hex Socket Head Bolt M4x16

Hex Socket CS Head Bolt M5x8

Safety Wire

Speed Controller

Fell 10.20

Seal Plate

Feb -29- 96 US

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested before leaving the factory It is wmanted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, rerum the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita wlll repair (or at our option, replace) without charge.

-

This Warranty does not apply where: repairs have been made or attempted by others: repairs are required because of normal wear and tear:

* T h e tool has been abused, misused or improperly maintained alterations have been made to the tool

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CON-

SEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER

APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.

MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES. INCLUDING IMPLIED

WARRANTIES O F "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE,"

AFTER THE ONE-YEAR TERM OF THIS WARRANTY

This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts. so the above limitation may not apply to you

Makita Corporation

of

America

2650 Buford Hwy., Buford GA 30518

MCA 4/00

PRINTED IN USA

2000-09-4D

No results