Technical Bulletin
Application Note
May 2013
Installing and Configuring a
NetBackup 6.5 Client or Media Server
Summary
This application note describes how to install the Symantec NetBackup 6.5 backup Client or Media Server
solution on an Overland SnapServer DX1 or DX2.
10400448-001 05/2013
©2013 Overland Storage, Inc.
Page 1 of 6
Backup Agent/Media Server Install
Overview
This application note describes how to install and use the Net Backup 6.5 client or media server on
a SnapServer DX1 or DX2 running GuardianOS 7.x.
Required Information, Tools, and Files
Before performing the installation procedures on SnapServer, the following information, tools,
and files are required.
Backup and Media Server IP Addresses
Most backup agents must know the IP addresses of the backup and media servers that will be
used with the SnapServer. From the Maintenance >Tools >Host File Editor page in the Web
Management Interface, provide a host-name to IP-address mapping that persists across system
reboots.
Unix/Linux client
When you configure a backup server to see the agent running on the SnapServer assume that the
server is a Unix or Linux client.
Secure Shell (SSH) client
To remotely install any backup solution on the server, you must have an SSH client installed on a
remote workstation. The SSH implementation requires SSH v2. If you do not already have an SSH
client application installed, you can download one from the Internet. The commands must be
entered via SSH to install your backup agent are case-sensitive; therefore the commands must be
entered exactly as shown.
Backup and Restore Path Location
Backup servers often request the path for backup and restore operations on the backup agent.
Specify the path relative to share mount points on the server as /shares/sharename (where
sharename is the name of the share to be backed up). If you have accepted the default SnapServer
configuration, the correct path is /shares/SHARE1.
Password Expiration Policies
If the backup application uses a specific local user account to perform backups, ensure that the
user is exempt from password expiration policies, if enabled (see the Online Help for procedures to
set password policy for local users).
10400448-001 05/2013
©2013 Overland Storage, Inc.
Page 2 of 6
Backup Agent/Media Server Install
Linux Agent Installers - GSU file
Overland Storage provides the NetBackup 6.5 client and server installers in the form of GSU files
that can be installed through the standard OS upgrade procedure. You can get additional
technical support on the Internet at http://support.overlandstorage.com, or by contacting
Overland Storage using the information found on the Contact Us page on our website.
Preinstallation Tasks
Perform the following tasks prior to installing any solution:
1. In the Web Management Interface, navigate to the Maintenance > Host File Editor page and
click Add.
2. Enter the IP address of the backup or media server and enter one or both of the following
names (as required by your backup environment):
•
Host name (long form) – Enter the fully qualified address for the backup server using
a myserver.mydomain.com format.
•
Host name (short form) – Enter an abbreviated address for the backup server using a
myserver format.
3. Click OK. The entry appears on the Host Editor page.
4. Repeat Steps 2–3 for each backup and media server with which the agent installed on the
server needs to communicate.
5. Navigate to the Server > SSH page, make sure the Enable SSH box is checked, and then click
OK.
SSH is immediately available.
CAUTION: To maintain security, SSH should be disabled when not in use.
NetBackup 6.5 Client and Server Installation
The NetBackup 6.5 client backs up the SnapServer to another media server only. The NetBackup
server configures the SnapServer as a NetBackup media server to backup the SnapServer to a
tape drive or library attached to the SnapServer.
Installing the NetBackup 6.5 Client
The GSU file for the NetBackup 6.5 client is available for download from Overland Storage.
Upload the Client Installer GSU
To install on a SnapServer, follow these installation instructions:
1. Download and save the appropriate GSU version to the client used to log in to the Web
Management Interface.
2. Log in to the Web Management Interface and go to Maintenance > OS Update.
3. Click Choose File and browse to the GSU file containing the agent to install it.
4. Click OK on the OS Update page.
10400448-001 05/2013
©2013 Overland Storage, Inc.
Page 3 of 6
Backup Agent/Media Server Install
5. Click Update on the confirmation page.
6. Click Close.
Connect to the Server over SSH
1. Launch your SSH client and connect to the server.
2. Log in as admin (using the Admin password) to enter the CLI shell.
3. A standard Linux shell must be launched to install the agent. Type:
osshe11
4. Press Enter.
5. Change to the root by entering the following command:
su -
6. Enter the root password (same as admin password).
Run the Client Installer
1. Change to the client installer directory by entering the following:
cd /usr/local/NBClients/catalog/anb
2. To install the client enter:
./client.inst
3. Enter the name or IP address of the NetBackup server when prompted by the installer, and
accept the defaults otherwise.
4. To confirm successful installation, add the SnapServer to the NetBackup master server and
run a test backup job.
Installing the NetBackup 6.5 Server
There are two components that must be installed for the NetBackup 6.5 server: Symantec ICS
(Infrastructure Core Services) for NetBackup environment authentication and encryption, and
Netbackup 6.5 Server itself for media server functionality. GSU files for both packages to install
on a SnapServer are available for download from Overland Storage.
Upload the ICS and Server Installer GSUs
1. Download and save the two GSUs to the client used to log in to the Web Management
Interface.
2. Log in to the Web Management Interface and go to Maintenance > OS Update.
3. Click Choose File and browse to the Symantec ICS GSU file
(GuardianOS_7_2_NB_6.5_ICS.gsu agent).
4. Click OK on the OS Update page.
5. Click Update on the confirmation page.
6. Click Close.
7. Repeat Steps 2–6 using the NetBackup 6.5 Server GSU
(GuardianOS_7_2_NB_6.5_ICS.gsu agent).
Connect to the Server over SSH
1. Launch your SSH client and connect to the server.
10400448-001 05/2013
©2013 Overland Storage, Inc.
Page 4 of 6
Backup Agent/Media Server Install
2. Log in as admin (using the Admin password) to enter the CLI shell.
3. A standard Linux shell must be launched to install the agent. Type:
osshe11
4. Press Enter.
5. Change to the root by entering the following command:
su -
6. Enter the root password (same as admin password).
Run the ICS Installer
1. Change to the ICS installer directory by running the following command:
cd /usr/local/NB_65_ICS_1.4.37.0_LinuxX86
2. To install ICS, run the following command:
./installics
a. When prompted to choose from the Task Menu, choose I (Install / Upgrade).
b. When prompted to choose Symantec Infrastructure Core Services Installer 5.0, choose
1 (Symantec Private Branch Exchange).
c. When prompted for the PBX installation location, enter the name or IP address of the
SnapServer.
Run the Server Installer
1. Change to the NetBackup server installer directory by running the following command:
cd /usr/local/NB_65_LinuxR_x86_20070723/linuxR_x86/catalog/anb/
2. Run the following command to install NetBackup 6.5 Server:
./NB.inst
3. Accept defaults when prompted by the installer.
10400448-001 05/2013
©2013 Overland Storage, Inc.
Page 5 of 6
Backup Agent/Media Server Install
Validate Installation and Complete Configuration
1. To confirm successful installation, verify the NetBackup server processes are running by
entering the following:
/usr/openv/netbackup/bin/bpps -x
The server processes should be listed similarly to the following (there may be fewer if no
tape drive is attached):
NB Processes
-----------root 3808 1 0
root 3816 1 0
root 4349 1 0
root 4396 1 0
root 4416 1 0
root 4439 1 0
root 4453 1 0
10:51
10:51
10:52
10:52
10:52
10:52
10:52
MM Processes
-----------root 4338 1
root 13585 1
root 13876 13585
root 13879 13585
root 13884 1
0
0
0
0
0
?
?
?
?
?
?
?
00:00:00
00:00:00
00:00:00
00:00:00
00:00:00
00:00:00
00:00:00
10:52
11:00
11:00
11:00
11:00
?
?
?
?
?
/usr/openv/netbackup/bin/vnetd -standalone
/usr/openv/netbackup/bin/bpcd -standalone
/usr/openv/netbackup/bin/bpcompatd
/usr/openv/netbackup/bin/nbrmms
/usr/openv/netbackup/bin/nbsl
/usr/openv/netbackup/bin/nbcssc -a NetBackup
/usr/openv/netbackup/bin/nbsvcmon
00:00:00
00:00:00
00:00:00
00:00:00
00:00:00
vmd
/usr/openv/volmgr/bin/ltid
tldd
avrd
tldcd
2. Add the server to the NetBackup master server as a media server.
3. Run a test backup job to verify successful installation.
10400448-001 05/2013
©2013 Overland Storage, Inc.
Page 6 of 6
">