933307G
36 HYDRO MID-FS481V KAW FS
933307G
36 HYDRO MID-FS541V ES KAW FS
934306G
48 HYDRO MID-FS541V KAW FS
934307G
48 HYDRO MID-FS541V ES KAW FS
935308G
54 HYDRO MID-FS600V KAW FS
935309G
Rev. B 04-2013
MAN 4166108
54 HYDRO MID-FS600V ES KAW FS
OPERATOR’S MANUAL 4166109
PARTS MANUAL
933305G
CALIFORNIA
WARNING
Proposition 65 Warning
Diesel engine exhaust and some of
its constituents are known to the State
of California to cause cancer, birth
defects and other reproductive harm.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Californie Proposition 65 Avertissement
AVERTISSEMENT
Les échappements des moteurs diesel
et certains de leurs composés sont
reconnus par l’Etat de Californie pour
être cancérigènes, provoquer des défauts congénitaux et d’autres dangers
en matière de reproduction.
California Advertencia
L’émission du moteur de ce matériel
contient des produits chimiques que
l’Etat de Californie considère être
cancérigènes, provoquer des défauts
congénitaux et d’autres dangers en
matière de reproduction.
de la Proposicion 65
ADVERTENCIA
El estado de California hace saber
que los gases de escape de los motores diesel y algunos de sus componentes producen cáncer, defectos
de nacimiento y otros daños en el
proceso de reproducción humana.
El estado de California hace saber
que los gases de escape de este
producto contienen productos quÍmicos que producen cáncer, defectos
de nacimiento y otros daños en el
proceso de reproducción humana.
CALIFORNIA
Proposition 65 Warning
Battery posts, terminals, wiring
insulation, and related accessories
contain lead and lead compounds,
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.
WASH HANDS AFTER HANDLING.
Hydro
Midsize
IMPORTANT MESSAGE
Thank you for purchasing this Schiller Grounds Care, Inc.product. You have purchased a world class mowing product, one
of the best designed and built anywhere.
This machine comes with an Operation and Safety Manual and a separate Setup, Parts and Maintenance Manual. The useful
life and good service you receive from this machine depends to a large extent on how well you read and understand these
manuals. Treat your machine properly, lubricate and adjust it as instructed, and it will give you many years of reliable service.
Your safe use of this Schiller Grounds Care, Inc.product is one of our prime design objectives. Many safety features are
built in, but we also rely on your good sense and care to achieve accident-free operation. For best protection, study the
manuals thoroughly. Learn the proper operation of all controls. Observe all safety precautions. Follow all instructions and
warnings completely. Do not remove or defeat any safety features. Make sure those who operate this machine are as well
informed and careful in its use as you are.
BOB_CAT dealer for any service or parts needed. Schiller Grounds Care, Inc.service ensures that you continue to receive
the best results possible from Schiller Grounds Care, Inc.products. You can trust Schiller Grounds Care, Inc.replacement
parts because they are manufactured with the same high precision and quality as the original parts.
Schiller Grounds Care, Inc.designs and builds its equipment to serve many years in a safe and productive manner. For
longest life, use this machine only as directed in the manuals, keep it in good repair and follow safety warnings and instructions. You'll always be glad you did.
Schiller Grounds Care, Inc.
One Bob Cat Lane
Johnson Creek, WI 53038-0469
TABLE OF CONTENTS
FIGURES
PAGE
SAFETY...................................................................................................................................................................................................................2
ASSEMBLY/SET-UP INSTRUCTIONS............................................................................................................................................................. 3-13
LUBRICATION.................................................................................................................................................................................................14, 15
MAINTENANCE.............................................................................................................................................................................................. 16-18
SERVICE CHART.................................................................................................................................................................................................19
SERVICE RECORD..............................................................................................................................................................................................20
ADJUSTMENTS.............................................................................................................................................................................................. 20-24
BELT REPLACEMENT..........................................................................................................................................................................................25
PAGE INTENTIONALLY LEFT BLANK.................................................................................................................................................................26
PARTS SECTION..................................................................................................................................................................................................27
UPPER ENGINE DECK ASSY............................................................ FIGURE 1...........................................................................................28, 29
LOWER ENGINE DECK ASSY/CLUTCH........................................... FIGURE 2...........................................................................................30, 31
DRIVE WHEELS................................................................................. FIGURE 3...........................................................................................32, 33
PARKING BRAKE / DOCUMENT TUBE............................................. FIGURE 4...........................................................................................34, 35
RECOIL START UPPER HANDLE...................................................... FIGURE 5...........................................................................................36, 37
ELECTRIC START UPPER HANDLE................................................. FIGURE 6...........................................................................................38, 39
TRACTION CONTROLS..................................................................... FIGURE 7...........................................................................................40, 41
ELECTRIC START BATTERY............................................................. FIGURE 8...........................................................................................42, 43
HYDRAULICS..................................................................................... FIGURE 9...........................................................................................44, 45
POWER UNIT DECALS...................................................................... FIGURE 10.........................................................................................46, 47
WIRE DIAGRAM-RECOIL START...................................................... FIGURE 11.........................................................................................48, 49
WIRE DIAGRAM-ELECTRIC START.................................................. FIGURE 12.........................................................................................50, 51
WIRING SCHEMATIC-RECOIL START.............................................. FIGURE .13...............................................................................................52
WIRING SCHEMATIC-ELECTRIC START.......................................... FIGURE 14...............................................................................................53
CUTTERDECK MOUNTINGQ............................................................. FIGURE 15.........................................................................................54, 55
HYDROGEAR PUMP.......................................................................... FIGURE 16.........................................................................................56, 57
MOUNTING-36" FIXED DECK............................................................ FIGURE 17.........................................................................................58, 59
MOUNTING-48" FIXED DECK............................................................ FIGURE 18.........................................................................................60, 61
MOUNTING-54" FIXED DECK............................................................ FIGURE 19.........................................................................................62, 63
BAFFLES............................................................................................ FIGURE 20.........................................................................................64, 65
CASTER ASSY-FIXED DECKS........................................................... FIGURE 21.........................................................................................66, 67
SPINDLE ASSEMBLY......................................................................... FIGURE 22.........................................................................................68, 69
CUTTERDECK DECALS..................................................................... FIGURE 23.........................................................................................70, 71
WEIGHTS............................................................................................ FIGURE 24.........................................................................................72, 73
04-2013
1
SAFETY
Hydro
Midsize
NOTICE !!!
Unauthorized modifications may present extreme
safety hazards to operators and bystanders and
could also result in product damage.
This symbol means:
ATTENTION!
BECOME ALERT!
Your safety and the safety of others is involved.
Schiller Grounds Care, Inc. strongly warns against,
rejects and disclaims any modifications, add-on
accessories or product alterations that are not
designed, developed, tested and approved by Schiller
Grounds Care, Inc.'s Engineering Department. Any
Schiller Grounds Care, Inc.product that is altered,
modified or changed in any manner not specifically
authorized after original manufacture–including the
addition of “after-market” accessories or component
parts not specifically approved by Schiller Grounds
Care, Inc.–will result in the Schiller Grounds Care,
Inc.Warranty being voided.
Any and all liability for personal injury and/or
property damage caused by any unauthorized
modifications, add-on accessories or products not
approved by Schiller Grounds Care, Inc.will be
considered the responsibility of the individual(s) or
company designing and/or making such changes.
Schiller Grounds Care, Inc.will vigorously pursue
full indemnification and costs from any party
responsible for such unauthorized post-manufacture
modifications and/or accessories should personal
injury and/or property damage result.
Signal word definitions:
The signal words below are used to identify levels
of hazard seriousness. These words appear in this
manual and on the safety labels attached to Schiller
Grounds Care, Inc.machines. For your safety and
the safety of others, read and follow the information
given with these signal words and/or the symbol
shown above.
DANGER indicates an imminently hazardous
situation which, if not avoided, WILL result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
CAUTION indicates a potentially hazardous situation
which, if not avoided, MAY result in minor or moderate
injury. It may also be used to alert against unsafe
practices or property damage.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, MAY result in property damage.
MODEL NUMBER: This number appears on
sales literature, technical manuals and price lists.
SERIAL NUMBER: This number appears only
on your mower. It contains the model number
followed consecutively by the serial number.
Use this number when ordering parts or seeking
warranty information.
Located on engine deck top, left side.
2
Hydro
Midsize
ASSEMBLY/SET-UP INSTRUCTIONS
GENERAL NOTE: FRONT, REAR, RIGHT HAND AND LEFT HAND REFERENCES BELOW
ARE WITH RESPECT TO AN OPERATOR AT THE CONTROLS.
1. UNCRATE - Place shipping crate on a level surface and remove sides and top.
2. Remove screws securing shipping brackets A to
pallet. Remove 2 front shipping brackets and
tighten front axle bolts.
3. Remove wire ties B securing tires, upper handle,
rods, and parts bag.
Raise rear of machine and support at location C
on jackstands. Remove rear shipping brackets.
Keep nuts. install drive wheels using the nuts
removed from the shipping brackets. Torque to
85 ft./lbs.
NOTE: One side of the wheel is dished deeper
than the other.
On 36" units install with the deep dish to the
inside.
on the 48" & 52" units, install with the deep dish
on the outside.
Tighten wheel nuts securely. Torque to 85ft./lbs.
3
ASSEMBLY/SET-UP INSTRUCTIONS
4. Install upper handle B to lower handle D using
(2) 3/8-16 X 1-1/2" bolts and (2) 3/8-16 serrated
flange nuts through upper holes F. Install (2) 3/816 X 1 bolts and (2) 3/8-16 locknuts through hole
E and one of the three holes on D to give desired
handle height.
5. Loosen bolt X connecting the Brace Y to lower
handles. Align top of brace so the upper handle
B is between the slot and hole.
6. Install U bolt U around upper handle and through
hole and lot in the brace.
7. Install nylock nuts W on both ends of U-bolt and
tighten. Repeat on other side.
4
Hydro
Midsize
Hydro
Midsize
ASSEMBLY/SET-UP INSTRUCTIONS
8. Route cables and wires as shown, and tie
harness to upper handles as shown.
9. After installing handles, make sure to check the
throttle and choke setting are correct.
Check the throttle at idle and full throttle. The
lever should contact the upper stop at idle and
thelower stop at full throttle.
Make sure the choke is fully open with the choke
cable pused all of the way in, and fully choked
with the cable pulled all of the ay out.
HIGH IDLE STOP
LOW IDLE STOP
WITH THE CHOKE CABLE PUSHED IN,
THE TWO LEVERS SHOULD ALMOST
TOUCH.
HIGH IDLE STOP
5
ASSEMBLY/SET-UP INSTRUCTIONS
10. Install spring on bolt A. Repeat for other side.
11. Install 3/8-16 nylon locknut to end of bolt on both
sides as shown.
12. Open the bypass valves X on each pump by
rotating handle counter-clockwise two turns.
6
Hydro
Midsize
Hydro
Midsize
ASSEMBLY/SET-UP INSTRUCTIONS
13. Cut and remove tie wrap G from the traction
control lever H.
14. Locate the two longest rods removed in Step 3.
Install the two traction control rods through the
traction control lever H, flatwasher and traction
lock J and secure with hairpins. Repeat on other
side of upper handle.
NOTE: The flat washer in the inside of the traction
control lever.
15. With the traction locks J in the neutral position,
apply tension to the traction control rod to
remove any slack and align swivel on traction
control rod with the hole in pump arm K and
install washer and hairpin clip. Repeat for other
side.
NOTE: The pump arm has some rotational play.
Adjust the swivel on the traction control rod to the
center of this play and secure to the pump arm
with a flatwasher and hairpin as shown.
7
ASSEMBLY/SET-UP INSTRUCTIONS
16. Attach spring to pump arm and then to bolt L.
Repeat for other side.
17. Connect speed control rod M to the speed control
lever N and secure with hairpin. Repeat for other
side. Install swivel to lower end of rods.
18. Set the speed control levers to neutral and adjust
the swivel on the lower end of the speed control
rod M so they engage the very top of the slot on
the neutral plates P and secure with flatwasher
and hairpin as shown. Repeat for other side.
8
Hydro
Midsize
Hydro
Midsize
ASSEMBLY/SET-UP INSTRUCTIONS
19. Insert threaded end of brake rod Q through the
slot on the engine deck and attach the other end
to the brake control arm R and secure in place
with hairpin S as shown.
20. Connect swivel on threaded end of brake rod
Q to the brake arm T and secure in place with
hairpin S as shown. Adjust swivel to provide
adequate braking when the brake control arm is
engaged. See adjustment section of this manual.
21. Close bypass valve X by rotating clockwise until
firmly seated.
9
ASSEMBLY/SET-UP INSTRUCTIONS
22. Install fuel line F1 from the engine fuel filter side
to the fuel pick-up fitting as shown. Ensure inline fuel valve F3 is open before starting. Install
purge fuel line, F2, from engine carb purge port
to vent on top the fuel tank.
23. On Electric Start Models Only
Batteries come with acid. Check level and
charge before startup.
Remove the battery cover and the battery from
the machine. Fill the battery to the bottom of
the vent wells with electrolyte and trickle charge
for several hours. Replace the battery in the
machine and make the connections, red to
positive first, then black (ground) to negative.
Install battery cover and secure with previously
removed nuts.
10
Hydro
Midsize
Hydro
Midsize
ASSEMBLY/SET-UP INSTRUCTIONS
24. Fill engine with oil. (See engine manual for specifications.)
25. Fill fuel tank with clean, fresh unleaded fuel.
•
•
•
•
•
•
•
GASOLINE IS HIGHLY FLAMMABLE!
Fill fuel tank with good quality, clean, regular unleaded gasoline.
Do not use hi-test fuel.
Do not smoke.
Do not spill fuel.
Fill outdoors.
Do not overfill. Fill to 1" below bottom of filler neck to allow room for expansion.
USE A FUNNEL TO FILL GAS TANK
26. Check oil level in hydraulic oil reservoir and adjust as necessary.
27. Adjust tire pressure in drive wheels and casters to 14 psi (1 kg/cm2).
28. Before attempting to start the mower, read and understand all sections of the Operation & Safety
manual.
29. Inspect safety circuit so that works properly.
NOTICE: Special setup instructions.
•
Before engaging the cutterdeck, run the engine for five minutes at full RPM. This is recommended for
new engine installation to permit complete engine lubrication prior to load.
•
Do not engage the cutterdeck at full throttle. Set the throttle half way between the highest and lowest
engine speed, engage the PTO switch and increase the engine speed to full before cutting.
•
Do not use this machine without an approved grasscatcher, grass discharge chute or mulching plate(s)
correctly fitted.
11
ASSEMBLY/SET-UP INSTRUCTIONS
Make all adjustments with the engine shut off, spark
plug wire disconnected and mower drive disengaged.
FIXED CUTTERDECK HEIGHT OF CUT
The cutting height is determined by the position of
the blades in relation to the wheels. Variation to this
height may be made at THREE points. (See Height
of Cut Charts below).
1. THE CASTER WHEELS
1. Remove the quick pin P from the top of the
caster wheel pivot spindle.
2. Place required spacers above or below
wheel support bracket and replace the quick
pin P.
Hydro
Midsize
2. CUTTERDECK BLADE SPINDLES
NOTE: See MAINTENANCE section of the Setup,
Parts & Maintenance manual for blade removal and
replacement procedures.
1. Remove belt cover.
2. Remove nut N from the top of the cutter spindle
bolt.
3. Withdraw the cutterdeck spindle bolt (from
bottom) complete with washer, blade and
spacers 4. Place the required number of spacers (no more
than 2) on the cutterdeck spindle bolt below the
cutterdeck, between blade and spindle shaft.
5. Fit any excess spacers on the cutterdeck spindle
bolt above the deck, between the conical washer
and the nut. Replace nut and tighten to 70 ft-lbs.
4109861
A(1/8")
1
2
3
4
5
B(1/4")
C(1/2")
CUTTING HEIGHT
MM
IN
35
1.375
41
1.625
48
1.875
54
2.125
60
2.375
2.625
67
73
2.875
3.125
79
3.375
86
3.625
92
3.875
98
4.125
105
4.375
111
4.625
118
12
A
1
1
1
1
1
1
1
1
1
1
1
1
1
1
B
1
1
1
0
0
0
1
1
1
0
0
0
1
1
C
0
0
0
2
2
2
3
3
3
5
5
5
6
6
UPPER BOLT POSITION
5
5
5
4
4
4
3
3
3
2
2
2
1
1
NUMBER OF
SPACERS BETWEEN
SPINDLE
AND BLADE
(1/4" THICK)
2
1
0
2
1
0
2
1
0
2
1
0
2
1
ASSEMBLY/SET-UP INSTRUCTIONS
Hydro
Midsize
SETTING CUTTERDECK HEIGHT
CUTTERDECK POSITION
.
1. Support rear of power unit.
2. Place blocks under both outside edges of cutterdeck at B. See Block chart below.
CUTTING
HEIGHT
HOLE
POSITION ON
ENGINE
DECK*
BLOCK
HEIGHT AT
REAR OF
DECK (B)
1.375" - 1.625"
5
1.25"
1.875" - 2.375"
4
2.00"
2.625" - 3.125"
3
2.75"
3.375" - 3.875"
2
3.50"
4.125" - 4.625"
1
4.25 "
* Position 1 is the highest hole
on the engine deck.
3. Remove (2) upper deck mounting bolts C.
4. Loosen (2) lower deck mounting bolts D several
turns. Loosen enough to allow easy movement
of the rear of cutterdeck. Allow deck to set down
on blocks or if deck is being raised, allow the
front casters to sit on the floor.
5. Reinstall upper deck mounting bolts C according
to the chart for the cut height desired.
6. Tighten all bolts and reinstall belt cover.
7. Remove rear support and blocks under the deck.
8. Your side discharge mower will give you the best
cut if the very tip of the front blade is 1/8" to 1/4"
lower then the rear of the rear blade.
13
LUBRICATION
Hydro
Midsize
MACHINE LUBRICATION
Every 50 Working Hours - Lubricate the following points with grease:
1)
2)
3)
Caster wheel pivots (2 points)
Neutral eccentric pin (2 points)
Idler pivot bearings:
a) Engine to cutterdeck belt tensioner
b) Cutterdeck belt tensioner
c) Hydro drive belt tensioner
NOTE: The spindles used on these machines use a superior sealed bearing which does not require relubrication.
14
LUBRICATION
Hydro
Midsize
ENGINE OIL
Do not perform engine maintenance without the
engine off, spark plug wires disconnected and PTO
disengaged.
AFTER FIRST FIVE (5) HOURS
While the engine is warm:
1. Release the oil drain hose assembly from the
engine clip J. Lay hose assembly over the frame
edge or through the frame cutout, which ever is
most convenient.
2. Remove the rubber cap D from the tip of the
hose assembly and turn the drain valve to allow
oil to drain from the engine. Dispose of used oil
in accordance with local requirements.
3. Clean drain valve and tighten the plastic portion
of the drain valve back into the metal portion of
the valve. Replace rubber cap over the tip of the
valve. Replace hose assembly back into engine
clip.
4. Change oil filter.
5. Fill the crankcase with fresh oil to the full mark.
Do not overfill. See engine manual for oil
specifications.
PERIODIC OIL CHANGES
1. See engine manual for oil and filter change intervals after the break-in period.
2. Follow instructions for first oil change, above.
DAILY
1. Check oil level with the dipstick.
2. If oil is needed, add fresh oil of proper
viscosity and grade. See engine manual for oil
specifications. Do not overfill.
3. Replace dipstick before starting engine.
15
MAINTENANCE
Hydro
Midsize
ENGINE - KAWASAKI
The maintenance schedule detailed is for average operating conditions. Under extreme conditions (dusty,
dirty or more than 8 hrs continuous use) maintain more frequently.
Cooling Fins and Air Intake screen (daily)
Ensure that the cooling fins and air intake screen
W are cleaned daily. Continued operation with
a clogged cooling system will cause severe
overheating and result in engine damage. You can
use compressed air to clean.
Air Cleaner
Dual element air cleaners have a paper air cleaner
element Z with an oiled, foam precleaner element V
on the dirty side of the paper element. Both should
be inspected regularly and maintained.
Clean and re-oil precleaner element every 25 hours
(more often under dusty conditions).
1. Turn knobs 1/4 turn counter-clockwise to remove
air cleaner cover F.
2. Loosen clamp X to remove air cleaner assembly.
3. Remove and wash precleaner V with kerosene or
liquid detergent and water.
4. Wrap precleaner V in a cloth and squeeze to
remove excess cleaning agent.
5. Saturate precleaner V with new engine oil and
squeeze to remove excess oil.
Every 100 hours (more often under very dusty or dirty
conditions), check the paper cartridge Z.
– Clean by tapping gently.
– Do not wash the cartridge or use compressed air
– Replace when cartridge is dirty, bent or
damaged.
6. Reinstall precleaner V over paper cartridge Z,
reinstall air cleaner assembly, tighten clamp X,
and reinstall cover F.
16
Hydro
Midsize
MAINTENANCE
Blade Sharpening
Blades may be sharpened by filing or grinding, but with either method the balance of the blades must be
maintained at 5/8 oz/in or less. Failure to maintain balance causes excess vibration, wear and shortened life
of not only the blades, but most all components of the machine. To balance a blade after sharpening: attach
1/8 oz of weight 5" from center on the light end. This should make the light end the heavy end. If it does not:
File or grind the heavy end until the addition of weight makes the light end the heavy end.
NOTE:
 Do not overheat or weaken the blades.
 Do not straighten bent blades. Replace with new
BOB-CAT blades.
If lift portion of blade is worn thin replace with a
new BOB-CAT blade.
 ALWAYS replace with BOB-CAT blades—do not
use another manufacturer’s blades as this could
be dangerous.
 Replace cracked or bent blades.
BLADE REMOVAL
1. Use a box wrench or socket with a long breaker
bar to remove spindle bolt under cutterdeck.
2. Slip tube over breaker bar or wrench if necessary
to gain leverage.
3. Keep hands clear as blades may rotate when bolt
releases.
4. When changing blades, wear thickly padded
gloves.
5. Block blades from turning by using a piece of
wood.
6. Follow these instructions to prevent injury when
bolt releases.
NOTE: To prevent blade from turning, place block of
wood at A, with grain perpendicular to blade.
BLADE RE-INSTALLATION
1. Place the desired number of spacers (no more
than 2) on the spindle bolt below the cutterdeck
between the blade and spindle shaft.
2. Insert the cutter spindle bolt (from bottom) complete with washer, blade and spacers.
3. Place remaining spacer(s) on the spindle bolt
above the cutterdeck between the conical washer
and nut (as shown). Replace nut and tighten to
70 ft-lbs.
Cutterdeck Pulley Assembly
17
MAINTENANCE
Hydro
Midsize
SPARK PLUG
 Remove plug and check condition.
 Good operating conditions are indicated if the plug has a light grey or tan deposit. A white blistered coating may indicate overheating. A black coating usually means an “over rich” fuel mixture caused by a
clogged air cleaner or improper carburetor adjustment. Do not sandblast, wire brush or otherwise try to
clean a dirty plug. Best results are obtained with a new plug.
 See engine manufacturers manual for proper spark plug gap.
HYDRAULIC RESERVOIR
CHECK, DRAIN AND FILL
Check level every 100 hours or when a leak has occurred. To check level: Remove reservoir cap. Add
10W30 oil until the oil level reaches the bottom of the
filler tube. Do not overfill.
EVERY 500 HOURS:
Change hydraulic oil and filter. Remove plug D to
drain reservoir. Remove and replace filter. Filter is
located on front of tank at G. Reinstall plug and fill
with 10W30 oil to the bottom of the filler tube F.
In-Line Fuel Filter
When required, the fuel filter X may be replaced.
See the Setup, Parts & Maintenance manual for service part numbers.
18
SERVICE CHART
Hydro
Midsize
NOTE: CHANGE ENGINE OIL AND FILTER AFTER FIRST 5 HOURS OF
OPERATION.
SERVICE
OPERATION
FIRST 5
HOURS
DAILY
EVERY
25
HOURS
EVERY
50
HOURS
EVERY
100
HOURS
EVERY
500
HOURS
ENGINE
Check Oil Level
X
Check for Oil & Air
Leaks
X
Clean Air Intake
X
Clean Air Cleaner
X
Change Oil & Filter*
X
SEE ENGINE MANUFACTURER'S MANUAL*
Clean Fuel Sediment
Bowl
Replace/Adjust
Spark Plug
X
SEE ENGINE MANUFACTURER'S MANUAL
HYDRAULIC OIL
RESERVOIR
Check Oil Level
X
Change Hydraulic
Oil
X
MACHINE
Check Tire
Pressures
Lubricate All Points
X
X
Consult the manufacturer’s manual for your engine
for further information and instructions.
19
SERVICE RECORD
Hydro
Midsize
NOTES
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
GENERAL
DATE
HRS
DATE
HRS
D ATE
HRS
DATE
HRS
DATE
Check Tire Pressures
Lubricate All Points
Check Nuts & Bolts
ENGINE
Check Oil Level
Change Oil
Clean
Air Cleaner Element
Clean Cooling Fins
Replace
Air Cleaner Element
Clean & Gap
Spark Plugs
NOTE: After first 5 hours of operation replace engine oil and filters.
20
HRS
DATE
HRS
Hydro
Midsize
ADJUSTMENTS
TRACTION DRIVE HYDROSTAT ADJUSTMENTS: The following adjustments must be done in order.
STEP 1 - Set Neutral
Neutral is set at the factory. If it should require
adjustment, raise the wheels off the ground by setting
the machine on jackstands or blocks. Disconnect
the traction control rod A and speed control rod R
at each pump end. Disconnect pump arm spring U
from bolt on engine deck. Loosen bolt S securing the
neutral plate eccentric shaft just enough to turn the
shaft. Start the engine and run at low speed. Turn
eccentric shaft T to raise or lower the point at which
the follower bearing is held in the center of the “V”
until the wheels stop turning. Tighten the eccentric
shaft bolt. Increase the throttle setting and check the
adjustment. Readjust if necessary. Shut the engine
off before proceeding to steps 2 and 3.
STEP 2 - Adjust Speed Control Rods
First adjust neutral, as outlined in Step 1. Set speed
control levers to neutral. Adjust swivels on lower
ends of speed control rods R so they just go into the
top of the slots on the neutral plates.
NOTE: If the speed control levers do not have
adequate tracking adjustment, the swivel on one of
the rods needs to be turned 1 turn.
STEP 3 - Adjust Traction Levers
Set neutral and adjust speed control rods as outlined
in Steps 1 and 2. Set traction locks in the neutral
position. Grasp traction rod A and pull down on it to
take out any slack. The pump control arm has some
back and forth play. Adjust the swivel to the center
of the control arm play. Connect the swivel to the
control arm. Reattach pump arm spring U to bolt on
engine deck.
NOTE: More reverse speed may be gained by
adjusting the swivel to the rear of the control arm
play. A minimum of 1/16" play is required so the
traction controls can be put in neutral without the
machine backing up.
21
ADJUSTMENTS
Make all adjustments with the engine shut off, spark
plug wire disconnected and mower drive disengaged.
NEUTRAL SWITCH ADJUSTMENT
The neutral switch N should be adjusted so that it
is engaged by the speed control lever C when in
the neutral position, and disengaged just before the
wheels being to move by adjusting the speed control
lever C from the neutral position to the forward
position.
TO ADJUST:
1. Complete the traction drive adjustments.
2. Place the machine on jack stands or blocks such
that the drive wheels are off the ground and the
machine is stable.
3. Adjust the speed control lever C to the neutral
position.
4. Adjust the neutral switch N to a position where
it will disengage just before the wheels move
by adjusting the speed control lever C from the
neutral position to the forward position.
PARKING BRAKE - Apply parking brakes and open
the bypass valves on the hydraulic pumps. Try to
push the machine forward. If wheels rotate, adjust
brakes as follows.
TO ADJUST:
1. Remove the hairpin cotter A from the brake rod
at the brake lever as shown.
2. Slide the brake rod out of the brake lever and
turn the rod in or out of the brake swivel B as
needed.
NOTE: The brake should initially be adjusted so
that the brake rod extends through swivel B 1" as
shown. If more brake pressure is required adjust
as necessary.
3. Reassemble brake rod to the brake lever using
hairpin A.
4. Apply parking brakes and try to push the machine
forward. If wheels rotate, readjust brakes.
5. Close bypass valves on the hydraulic pumps.
22
Hydro
Midsize
Hydro
Midsize
ADJUSTMENTS
OPERATOR PRESENT CONTROLS
The operator present (OP) controls should be adjusted to control the operation of the plunger of the
operator present switch (located under the right side
of the control panel). Depressing OP levers F should
depress the plunger; releasing the levers should
extend it.
TO ADJUST:
1. Loosen clamp bolts G on both ends, so clamps
can rotate on shaft.
2. Rotate actuator lever to depress switch plunger.
Keep OP levers against handles and tighten bolts
G.
3. When released, the OP levers should rise and
the actuator lever should rotate away from the
switch, allowing the switch plunger to extend
completely.
HANDLE BAR HEIGHT ADJUSTMENT
To adjust handle bar height: Remove bolts G and
loosen bolts E on each side of handlebars. Raise
or lower as required. Reposition upper handle and
reinsert bolts G into appropriate hole in lower handle
and tighten. Readjust traction control rods, parking
brakes and speed control rods.
Speed Control Lever Friction
The speed control lever is held where set by friction
pads. If the setting will not hold, tighten nuts E to
increase friction on the speed control lever.
Adjust Knob D to get machine to track in a straight
line.
23
ADJUSTMENTS
TRACK WIDTH ADJUSTMENT
The track width originally set from the factory can be
increased an additional 3-1/4" overall by performing
the following steps.
1. Loosen wheel lug nuts on both drive tires.
2. Raise rear of unit so that drive tires are off the
ground. Support the unit with jack stands.
3. Remove wheel lug nuts and wheels. Reattach
wheels with the tires rotated so the wheel offset
is the opposite of when they were previously
installed. Reinstall and tighten lug nuts until they
are snug.
4. Lower machine off of the jack stands and torque
wheel lug nuts to 85 ft-lbs.
TIRE PRESSURE ADJUSTMENT
Tire pressures should be maintained at 14 psi
(1.0 kg/cm2).
24
Hydro
Midsize
Hydro
Midsize
BELT REPLACEMENT
PTO BELT
1. Rotate idler arm using a 3/8" ratchet or breaker
bar and remove belt.
CUTTERDECK BELT
1. Remove PTO belt.
2. Rotate idler arm using a 3/8" ratchet or breaker
bar and remove belt.
3. Replace in the reverse order.
PUMP-DRIVE BELT
1. Remove PTO belt from the engine clutch.
2. Disconnect the clutch wire harness.
3. Unbolt clutch bracket from clutch and rotate the
clutch to allow enough clearance to remove the
clutch bracket.
4. Rotate idler arm using a 3/8" ratchet or breaker
bar inserted into the square hole in the idler arm.
5. Remove pump drive belt.
6. Replace by following steps in reverse order.
View under engine deck
25
THIS PAGE
INTENTIONALLY LEFT
BLANK
Hydro
Midsize
PARTS
SECTION
27
UPPER ENGINE DECK ASSY
Hydro
Midsize
FIGURE 1
4
USE THIS SET UP WITH TANK P/N 4165561
5
P/N LOCATED ON BOTTOM OF TANK
3
4
30
6C
5
29
6A
TO ENGINE PURGE PORT
1
42
2
41
5
6B
5
40
5
5
5
39
5
7
29
39
5
7
TO
E
NG
TO ENGINE
INE
20
14
22
USE THIS SET UP WITH TANK P/N 4163068-1
P/N LOCATED ON BOTTOM OF TANK
22
26
21
WIRE
HARNESS
16
27
24
23
25
19
38
15
19
37
28
36
15
18
9
12
13
17
12
13
17
TORQUE TO
8 - 12 FT/LBS
8
10
28
UPPER ENGINE DECK ASSY
Hydro
Midsize
FIGURE 1
ITEM PART NO.
DESCRIPTION
1 4167989
CAP-FUEL GASOLINE 3.5
2^4165561 TANK-FUEL
3 4165864
VALVE-INLINE FUEL
4 88042-1
CLAMP-HOSE 3/16
5 88042N
HOSE CLAMP 6 4162977-001 HOSE,FUEL LINE 56"
6A CUT TO 2"
6B CUT TO 18.5"
6C CUT TO 36.5"
7 4168368
8 4131068.2
9 64123-39
10 64229-05
11 2306144
12 64163-31
13 64006-03
14 69053-03
15 64229-02
16 2306127
17 64123-15
18 4164391.7
19 64018-9
20 4164251
21 48412
2288042-03
23 4164361
4164362
4164363
4164382
4164383
4164537
4164535
4164586
QTY
ITEM PART NO.
1
1
1
2
A/R
1
36 64141-6
37 48228-12
38 64123-54
FILTER, FUEL 1
DECK-ENGINE HYDRO
1
BOLT-HEX 1/2-13X1-1/4
8
LOCKNUT, 1/2-13 NYLON 8
S DOCU TUBE W/LAB
1
WASHER
4
LOCKWSHR-HELICAL 3/8 4
HOSE-HYDR 3/8X17"
1
LOCKNUT-NYLON 5/16-18 4
S-HYD RESEVOIR W/LABS 1
BLT-HEX 3/8-16X3/4
4
HANDLE-LOWER P-GRIP 1
BLT-CRG 5/16-18 X 3/4
4
VALVE-OIL DRAIN
1
CLIP-J CABLE 5/8X8.74
1
CLAMP--HOSE
2
ENG- KAW FS481V
1
ENG- KAW FS541V
1
ENG- KAW FS600V
1
ENG- KAW FS541V ES
1
ENG- KAW FS600V ES
1
FILTER-OIL KAW 49065-7007
FILTER-AIR ELEMENT
FILTER-PRE ELEMENT
DESCRIPTION
NUT-WLF 5/16-18
CLIP-CABLE, ISULATED
BLT-HEX 5/16-18X3/4
QTY
1
1
1
ITEMS 39-40 ARE USED WITH GAS TANK P/N
4163068-1
39 4162977-007 S HOSE-FUEL LINE 8"
2
40 4163012
FITTNG-90° FACE SEAL
1
41^4163068-1 TANK-FUEL
1
(INCLUDES ITEMS 40)
42 4130320
CAP-FUEL GASOLINE 3.5 1
^GAS TANK P/N IS LOCATED ON THE BOTTOM
OF THE GAS TANK ONCE IT IS REMOVED.
*NOT ILLUSTRATED
24 64205-018 BLT MET M8-1.25X15
1
25 64002-04
LOCKWASHER, EXT. 5/16 1
26 4164252-01 FITTING-3/8NPT-3/8 BARB 1
2769216.7 CAP-RESERVOIR
1
28 4164359
MUFFLER-MIDSIZE FS600 1
294163016 VALVE-FUEL
1
30 4162989-001 HOSE-FUEL
1
31* 4132325
GROMMET-FUEL TANK
1
32* 4165387
GROMMET-ROLLOVER VNT1
33* 4165763
VENT-FUEL TANK
1
34* 4165668
FILTER-FUEL IN TANK
1
35*4165667 FITTING-BARB
1
29
LOWER ENGINE DECK ASSY/CLUTCH
FIGURE 2
36
30
Hydro
Midsize
LOWER ENGINE DECK ASSY/CLUTCH
Hydro
Midsize
ITEM PART NO.
1
2
3
FIGURE 2
DESCRIPTION
2721647PULLEY-4.50E.O.D.
64163-31 WASHER, 25/64 X 1 X 12
2721110CLUTCH-ELECTRIC
(INCLUDES ITEM 30)
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
9
1
4
2721331.7 WLDMT-CLUTCH STOP MID 1
5
2721642 BELT-HA 49.0
1
6
2722244 PULLEY- A SECTION 4.50 2
7
38304-03 BRG-FLANGED PLASTIC
1
8
4121540PIN-CLUTCH
1
9
64123-15 BOLT-3/8-16X3/4 HEX
1
10
2721641.7 WLDMT-IDLER ARM
1
11 4116712PIN-PIVOT
1
12 64163-65 WASHER 0.890 X 1.375
6
13 64221-04E-RING.875
2
14
64123-138 BLT-HEX 3/8-16X3-3/4
1
15
64268-03 NUT-FL NYL LOCK 3/8-16 4
16
2308000 PULLEY-IDLER 4.00 EOD
1
17 33148-01SPACER
1
1838219 SPRING-TENSION
1
19
64123-87 BLT-HEX 3/8-16 X 1-3/4
1
20
64141-4 NUT-WLF 3/8-16
3
21
64163-51 WSHR.453 X 1.38 X 7GA
1
22 64006-03WASHER-LOCK
4
23
64123-155 BLT-HEX 7/16-20 X 3
1
24
64006-06 LOCKWSHR-HELICAL 7/1 1
25
64123-54 BOLT, 5/16-18X3/4 HEX
2
26
64163-55 WASHER .328X.75X14 GA 4
27
64229-02 LOCKNUT-NYLON 5/16-18 2
28
64164-12 1/4X1/4X1 SQ END KEY
1
29
64123-75 BOLT, 3/8-16X3 HEX
2
30
2720949 ASSY-CLUTCH WIRE
1
31
4163316 PUMP-HYDRO LH
1
32
4163317 PUMP-HYDRO RH
1
33
2721541 PULLEY-IDLER 5 IN
1
34
2721401.7 WLDMT-IDLER ARM
1
35
64163-61 WSHR .81X.406X16GA
1
36
64123-16 BLT-HEX 3/8-16X1-1/4
8
37 2188131SPRING-EXTENSION
1
38
4131068.2 DECK-ENGINE HYDRO
1
39 4116691PIN-PIVOT
1
40
64205-013 BLT-MET M6-1 X 12
2
41
64044-6 SCREW-SET 5/16-18X1/4
4
42
64238-03 KEY-MET 5MM SQ X 28
2
43
64209-09 WASHER-CONICAL SPRING2
44
64229-03 LOCKNUT-NYLON 3/8-16
3
45
64123-70 BOLT-HEX 3/8-16X1-1/2
1
31
DRIVE WHEELS
FIGURE 3
32
Hydro
Midsize
DRIVE WHEELS
Hydro
Midsize
ITEM PART NO.
FIGURE 3
DESCRIPTION
QTY
1
2
3
4131068.2 DECK-ENGINE HYDRO
1
2721620WLDMT-HUB
2
2721956 ASSY-WHEEL 16 X 7.50 X 8 2
2721956-01TIRE-16X7.50 X 8 MLTI TRC 1
2721956-02WHEEL W/ DUAL VALVES 1
4
5
6
7
8
9
64267-01
64025-06
2308051
64141-13
64164-28
64123-72
NUT-HEX FLANGED 1/2-20
NUT-HEX 3/4-16 2A
MOTOR-WHEEL ROSS MF
NUT WLF 1/2-13
#808 WOODRUFF KEY
BLT-HEX 1/2-13X2-1/2
ITEM PART NO.
DESCRIPTION
QTY
8
2
2
8
2
8
33
PARKING BRAKE/DOCUMENT TUBE
Hydro
Midsize
FIGURE 4
13
16
3
12
7
7
8
14
18
17
19
15
5
2
11
3
1
4
6
9
4
10
14
34
PARKING BRAKE/DOCUMENT TUBE
Hydro
Midsize
ITEM PART NO.
FIGURE 4
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
4131746
BRAKE SHAFT W/LABS
1
233103
SWIVEL
1
3 64168-2
COTTER-HAIRPIN.08X1.192
4
64001-6
NUT-HEX JAM,3/8-16
2
5
64123-138
BLT-HEX 3/8-16X3-3/4
1
62188131 SPRING-EXTENSION
1
7 2183071-01SPACER-15.88X10.32X16 2
8
64171-2
WAVE WASHER
1
9
4131072.7
PLATE-BRK SHFT RETNR 2
10 64123-50
BOLT-HEX 3/8-16X1
3
11 64163-02
WSHR-.325 X .596 X 11GA 1
12 64123-82
BOLT-HEX 3/8-16X2-1/2
1
13 38404-01
GRIP-CONTROL LEVER
1
14 64229-03
LOCKNUT-NYLON 3/8-16
5
15 4132134
ROD-PARK BRAKE
1
164166033.7 LEVER-BRAKE
1
17 38061A
CAP-DOCUMENT TUBE
1
184129802 TUBE-DOCUMENT
1
19 64152-27
SCREW-1/4-20X5/8 SP LG 2
35
RECOIL START UPPER HANDLE
Hydro
Midsize
FIGURE 5
20
24
33
25
29
3
26
7
4
21
9
6
20
1
2
13
11
10
34
35
12
9
11
8
9
13
30 23
27
6
10
17
31
19
5
18
17
28
32
14
14
15
16
22
36
RECOIL START UPPER HANDLE
Hydro
Midsize
ITEM PART NO.
1
2 *
FIGURE 5
DESCRIPTION
PL5029GRIP-HANDLE
2308121 ADHESIVE-3 GRAM TUBE
(USE WITH PL5029 GRIP)
QTY
ITEM PART NO.
DESCRIPTION
QTY
2
1
3
38148
SWITCH-ENGINE STOP
1
4
64152-46 SCR-SLT HH 10-24X1/2
2
5
4166101 S UPR HNDL HYD W/CHK 1
6
2303023CONNECTOR-OP
2
7
4122104 ROD-HANDLE LINK, LH
1
8
4122107 ROD-HANDLE LINK, RH
1
9
64168-2 COTTER-HAIRPIN.08X1.194
10
64197-002 BLT-TDFM 1/4-20X3/4
2
11 33030-09IDLER-BUSHING
2
12
4122056 WLDMT-OP PRESENCE
1
13
38371-01 BRG-NYLINER 3/8
2
14
64123-50 BOLT-HEX 3/8-16X1
4
15
4164391.7 HANDLE-LOWER P-GRIP 1
16
64141-4 NUT-WLF 3/8-16
4
17
64025-15 NUT-HEX #10-24 KEPS
4
18 38357-09CONTROL-THROTTLE
1
1938383 SWITCH-N.C.
2
20
2302152.7 HNDL-OP PRESENT
2
21 2721505SWITCH-PTO
1
22
64163-83 WASHER-.406 X 1.00 X.25 2
23
64163-03 WSHR-.256IDX.62ODX18GA2
24
64188-44 PIN-CLEVIS 3/16 X 2.25
2
25
64175-01 PUSHNUT-3/16 ROD
2
26
38371-03 BRG-NYLINER 3/16
4
27
64197-015 BLT-TDFM 10-32X1/2
2
28
4166096.7BRACE-HANDLE
2
29 2308065SPRING-TENSION
2
30
64229-01 LOCKNUT-NYLON 1/4-20
4
31 64225-03U-BOLT
2
32
108208
SWITCH DBL POLE NC/NO 1
33
108009-03 CONTROL CHOKE 51"
1
34
64025-04 NUT-HEX 3/8-24
1
3564152-49
SCRW-SLT HH #10-24X3/42
* NOT ILLUSTRATED
37
ELECTRIC START UPPER HANDLE
Hydro
Midsize
FIGURE 6
20
24
33
25
29
3
26
7
4
21
9
6
20
1
2
13
11
10
34
35
12
9
11
8
9
13
30 23
27
6
10
17
31
19
5
18
17
28
32
14
14
15
16
22
38
ELECTRIC START UPPER HANDLE
Hydro
Midsize
ITEM PART NO.
1
2 *
FIGURE 6
DESCRIPTION
PL5029GRIP-HANDLE
2308121 ADHESIVE-3 GRAM TUBE
(USE WITH PL5029 GRIP)
QTY
ITEM PART NO.
DESCRIPTION
QTY
2
1
3 128010SWITCH-ENGINE
1
4
64152-46 SCR-SLT HH 10-24X1/2
2
5
4166161 S UPR HNDL HYD W/CHK 1
6
2303023CONNECTOR-OP
2
7
4122104 ROD-HANDLE LINK, LH
1
8
4122107 ROD-HANDLE LINK, RH
1
9
64168-2 COTTER-HAIRPIN.08X1.194
10
64197-002 BLT-TDFM 1/4-20X3/4
2
11 33030-09IDLER-BUSHING
2
12
4122056 WLDMT-OP PRESENCE
1
13
38371-01 BRG-NYLINER 3/8
2
14
64123-50 BOLT-HEX 3/8-16X1
4
15
4164391.7 HANDLE-LOWER P-GRIP 1
16
64141-4 NUT-WLF 3/8-16
4
17
64025-15 NUT-HEX #10-24 KEPS
4
18 38357-09CONTROL-THROTTLE
1
19
2308094 SWITCH-N.C.NC DBL POLE 2
20
2302152.7 HNDL-OP PRESENT
2
21 2721505SWITCH-PTO
1
22
64163-83 WASHER-.406 X 1.00 X.25 2
23
64163-03 WSHR-.256IDX.62ODX18GA2
24
64188-44 PIN-CLEVIS 3/16 X 2.25
2
25
64175-01 PUSHNUT-3/16 ROD
2
26
38371-03 BRG-NYLINER 3/16
4
27
64197-015 BLT-TDFM 10-32X1/2
2
28
4166096.7BRACE-HANDLE
2
29 2308065SPRING-TENSION
2
30
64229-01 LOCKNUT-NYLON 1/4-20
4
31 64225-03U-BOLT
2
32
108208
SWITCH DBL POLE NC/NO 1
33
108009-03 CONTROL CHOKE 51"
1
34
64025-04 NUT-HEX 3/8-24
1
3564152-49
SCRW-SLT HH #10-24X3/42
* NOT ILLUSTRATED
39
TRACTION CONTROLS
Hydro
Midsize
FIGURE 7
62
40
TRACTION CONTROLS
Hydro
Midsize
ITEM PART NO.
FIGURE 7
DESCRIPTION
QTY
1
2
3
4
5
6
7
2722426
38189
64061-37
2303076
62464-5A
33243
2722242
* 2722243
GRIP-TRACTION LOCK
2
SPRING-COMPRESSION
2
ROLL PIN-1/8 X 1.00 SS
2
STUD-DOUBLE ENDED
2
WASHER,THRUST 5/16X3/4 2
SPACER
2
LATCH-ROLLER LH HYDRO 1
LATCH-ROLLER RH HYDRO1
8
9
10
11
12
13
14
15
16
64229-02
64229-01
2308002
64175-01
2308080
2721843.7
64168-2
2308065
2721660.7
* 2721622.7
5/16-18 NYLON LOCKNUT
LOCKNUT NYL 1/4-20
BRG-RADIAL W/THD STUD
PUSH NUT
BEARING SELF ALIGNED
ARM-RH SPEED CONTROL
HAIRPIN COTTER
SPRING EXTENSION
WLDMT-PUMP ARM RH
WLDMT-PUMP ARM LH
17
18
19
20
21
22
23
24
25
26
27 *
4
2
2
2
2
1
7
2
1
1
2722305 ROD-SPEED CONTROL
2
2721842.7 ARM-LH SPEED CONTROL 1
64163-06 WSHR.768/.756X1.25X14GA2
85010N
ZERK, 1/4-28 STR
2
64163-61 WSHR .81X.406X16GA
2
64061-28 ROLL PIN 3/16 X 1 1/4
2
2721617.7 WLDMT-SPEED CONTROL 2
4164391.7 HANDLE-LOWER P-GRIP 1
64123-50 BOLT, 3/8-16X1 HEX
2
2306081.7 WLDMT PUMP ARM
2
2308121 ADHESIVE
1
(USE WITH 38009N GRIP)
ITEM PART NO.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
DESCRIPTION
QTY
4117212 SPRING EXTENSION
2
64123-70 BOLT-HEX 3/8-16X1-1/2
4
64141-4 NUT-WLF 3/8-16
11
64123-202 BLT-HEX 3/8-16 X 9
1
64229-03 NUT-NYLOCK 3/8-16
3
2308066 FRICTION WASHER
2
38404-01 GRIP,CONTROL LEVER
1
2308076-02BEARING-PLASTIC
2
64192-04 SET SCREW 5/16-18X5/8
2
2303058 ECCENTRIC SHAFT W/ZRK 2
64123-02 BLT HEX 3/8-24 X 1
2
64006-03 WASHER, 3/8 HELICL LCK 2
64144-16RING,CLIP-.75X.062
2
38524
KNOB-4 PRONG 3/8-16
1
2721854 STUD-3/8-16X 3/8-24 4.5LG 1
64123-69 BOLT-5/16-18X1-1/2 HEX
2
118047-09 BUSHING-FLIP LOK.75ID
2
33030-08 BUSHING-IDLER7/8X3/8X11
138011
BALL JOINT
1
64001-2 NUT 3/8-16
1
2721844 BUSHING-SPEED CONTROL1
64268-03 NUT-FLG LYLOCK 3/8-16
2
TRACTION LOCK ASSY'S ARE ALSO AVAILABLE
4113565 S-TRCTN LOCK ASSY RH 1
(INCLUDES ITEMS 1-4, 6, 7, 9-12)
4113564
S-TRCTN LOCK ASSY LH 1
(INCLUDES ITEMS 1-4, 6, 7, 9-12)
* NOT ILLUSTRATED
28
64123-100 BOLT-3/8-16X2-1/4 HEX
1
29
64123-68 BLT-HEX 5/16-18 X 1
2
30
64139-13 BLT-WLF 5/16-18X1/2
4
31
64163-02 WSHR 21/64X19/32X11 GA 11
32
38372 BEARING BALL
4
33
2720312 SPRING-COMP IDLER PLT 1
3433103 SWIVEL
4
35
4122108 ROD-TRCTN CNTRL,HYDRO2
36
31032
LEVER TRACTION CNTRL 2
37
38009N
GRIP TRACTION CNTRL
2
38
64163-31 WASH 25/64X1X12 GA
4
39
64188-44 PIN-CLEVIS 3/16 X 2.25
2
40
64141-6 NUT-WLF 5/16-18
6
41
ELECTRIC START BATTERY
Hydro
Midsize
FIGURE 8
20
21
22
42
ELECTRIC START BATTERY
Hydro
Midsize
ITEM PART NO.
1
64229-02
264163-29
3128035
4
4131068.2
5
64262-002
6
112386
74167215
8
108061-16
9
64025-01
10 4113741
11 2722227-03
12 2722202.7
13 64197-016
14 4168907
1538665
16 64152-23
17 108061-15
18 64141-2
19 2308095
2064163-03
214168764.7
22 64152-56
FIGURE 8
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
LOCKNUT-NYLON 5/16-18 2
WASHER
2
COVER-BATTERY
1
DECK-ENGINE HYDRO
1
BLT-FLG 1/4-20 X 3/4
2
BOOT-BATTERY TERM POS 1
BATTERY
1
CABLE-BTTRY 31.5 BLACK 1
NUT-HEX 1/4-20
2
S-TRAY, BATTERY
1
CABLE-BTTRY W/CONDUIT 1
SUPPORT-BATT TRAY
2
BLT-TDFM 3/8-16X1/2
8
ROD,BATTERY HLD DWN 1
SOLENOID
1
1/4-20X3/8 LG SP SCREW 2
CABLE-BATTERY 6.5 RED 1
NUT-WLF 1/4-20
1
COVER, TERMINAL
3
WSHR-.256X.62X18GA
2
STRAP-BATTERY
1
SCREW-HS STAP #12 X 1/2 1
43
HYDRAULICS
FIGURE 9
44
Hydro
Midsize
HYDRAULICS
Hydro
Midsize
ITEM PART NO.
FIGURE 9
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
58026-01 3-WAY CONNECTOR
2
108029
PLUG, MAGNETIC
1
158058-04 FITTING-90 BARB, ADJ.
2
108205-02 ELBW-MALE 45 8X8 37-ORB4
88042-04 CLAMP-HOSE 5/8"
12
2720396 FLTR, 25 MCRN SM CAM
1
69060-01 FTG-BARB 9/16 X 3/8 ST
2
69216.7
CAP-RESERVOIR
1
64123-60 BOLT, 1/4-20X2 HEX
2
64229-01 LOCKNUT-NYLON 1/4-20
2
2306127 S HYD RESER W/LABS
1
2308051 MOTOR WHEEL ROSS
2
2692300-01HOSE-1/2 37/ORB X 18.5 LG2
2692300-02HOSE-1/2 37/ORB X 20.5 LG 2
4163317 PUMP-HYDRO RH
1
(SEE FIG 16 FOR PARTS BREAKDOWN)
16
4163316 PUMP-HYDRO LH
1
(SEE FIG 16 FOR PARTS BREAKDOWN)
(69053-05 IS A SERVICEABLE LENGTH OF 55")
17
69053-05 3/8 HI TEMP HOSE 17.0"
18
69053-05 3/8 HI TEMP HOSE 5.0"
19
69053-05 3/8 HI TEMP HOSE 5.0"
20
69053-05 3/8 HI TEMP HOSE 7.5"
21
69053-05 3/8 HI TEMP HOSE 6.8"
22
69053-05 3/8 HI TEMP HOSE 12.0"
1
1
1
1
1
1
ITEM PART NO.
DESCRIPTION
QTY
SERVICEABLE HYDRAULIC O-RINGS
SAE PORT 'O' RING
PART
NUMBER
THREAD
SIZE
AS568#
158061-10
9/16-18
-906
158061-11
3/4-16
-908
158061-12
7/8-14
-910
158061-13
1-1/16-12
-912
158061-14
1-5/16-12
-916
158061-16
1-5/8-12
-920
158061-03
1-7/8-12
-924
NOTE:
DO NOT use teflon tape on any hydraulic fittings.
Use a liquid pipe sealant.
45
POWER UNIT DECALS
Hydro
Midsize
FIGURE 10
1
OFF
PTO
(BLADES)
CHOKE
ON
PARKING
BRAKE
FAST
SLOW
OFF ON
N
NEUTRAL
START
R
N
SPEED CONTROL
F
4122168
BEFORE STARTING OR SERVICING:
-READ AND UNDERSTAND OPERATORS
MANUAL AND LABELS.
-BE SURE MACHINE IS IN SAFE OPERATING
CONDITION AND OPERATOR PRESENCE
WORKS. MAKE ANY NECESSARY REPAIRS.
-PUT TRACTION CONTROLS IN NEUTRAL.
-MOVE SPEED CONTROL TO "START".
-PUSH PTO SWITCH TO "OFF".
BEFORE LEAVING OPERATORS POSITION:
-PUT TRACTION CONTROLS IN NEUTRAL
-TURN PTO OFF.
-APPLY PARKING BRAKE.
-TURN ENGINE OFF.
-REMOVE KEY.
11
2
4
17
3
10
15
9
- DO
JUR NOT
ANDE PEOOPE
PET PLERAT
- DO
E
S
SAF NOT AT OR WH
DAM ERE
ETY USEA SAF
AGE FLY
- KEE .
E DIS
IF
ING
THE
REP P
TANPRO DEB
RE
OPELACLAB
CE.PER
ARE
TY. RIS
RATE IFELS,
KEEMAY
ANY
- OBE ORSLOSGUA
P PEO
INDOU
MA T ORRDS
MAY Y
SAF
NUA DAMAND
BTS
PLE
OTH CAU
L OF AGESHI
ABO
ERS SEETY
- DO
UT
. INJ INSTRU LOS D. ELD
URY
OPE NOT
T REP S IN
LAC PLA
TO CTIONS OR DAM
RAT DEF
YOU
E CE.
ION EAT
- DO
AGE
RSE. FAI
UNT NOT DAI INT
D.
LF LUR
RAI ALL LY. ERL
OR E TO
OCK
- DIS NED OW
DO
S.
DOI CON PER CHI
SO
CHE
NG NEC SONLDR
CK
ANY T
S TOEN,
UNS
MA SPA
OPE
INT RK
RATKILLED
ENA PLU
NCEG WIR E MA OR
.
E(S CHINE.
) BEF
ORE
13
9
HY
FILDRAU
INDL TO LIC
10WICA LEV OIL
30 TED EL
OIL WIT
.
H
HIG
H PR
- LEA
KS
ES
SU
- SEE
CAN
RE
FOR K
PEN
IMM
FL
OIL EDIA
ETR
UID
- SEE PEN
MET OPE ETRTE MED ATE
:
SER HOD RAT ATIO ICA SKI
N.
VICI OF ORS N
L
NG LOC MAN INJU ATT
RY. ENT
HYD ATIN
ION
RAU G UAL
LIC LEA FOR
SYSKS, PRO
TEMOR PER
.
5
2000
661
12
16
8
46
6
POWER UNIT DECALS
Hydro
Midsize
ITEM PART NO.
FIGURE 10
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
14164567
LABEL-CONTROL PNL W/CHK1
4122167 LABEL-CONTROL PNL HYD 1
2
3
4
5
6
7
8
9
2000672 LABEL-PARKING BRAKE 1
2000570 LABEL-WARN FUEL PICT 1
340830
LABEL-CAUTION SPANISH 1
2000571LABEL-IMPORTANT
1
4116761 LABEL-MADE IN USA
1
2000572 LABEL-WARNING BLADES 1
2000677 LABEL-DANGER/WARNING1
4164269 LABEL-ROT PRTS/B-WSHR 1
(LOCATED UNDER BELT COVER)
10
11
12
13
14*
15
16
17
2000704
2000673
2000661
2000590
4110260
4158401
4158400
4158402
LABEL-MIDSIZE PATENT
1
LABEL - OP MAN/TIRES
1
LABEL-HYD TANK WARN
1
LABEL-WARNING BATTERY 1
LABEL-TRACKING CNTRL 1
LABEL-BOBCAT, LARGE
1
LABEL-BOBCAT, MEDIUM 1
LABEL-BOBCAT, SMALL
1
* NOT ILLUSTRATED
47
WIRE DIAGRAM-RECOIL START
Hydro
Midsize
FIGURE 11
COLOR
RED
BLACK
YELLOW
BROWN
BLUE
ORANGE
BLUE W/WHITE STRIPE
PURPLE
WIRE
R
B
Y
BR
BL
O
BLW
P
ENGINE
KILL
ENGINE
GROUND
ENGINE
CHARGING
B
B
R
0
B
BL
1
CLUTCH
2
7
NEUTRAL
SWITCH
3
PTO
SWITCH
R
R
BR
R
BL/W
R
BR
Y
O
O
KEY
SWITCH
4
B
B
R
OPERATOR
PRESENCE
RELAY
9
O
B
B
BL
P
30
85
87A NC
87 NO
86
P
RELAY SCHEMATIC
B
Y
BL/W
48
OPERATOR
PRESENCE
SWITCH
FUSE
BLOCK
O
5
NC
O
NO
6
WIRE DIAGRAM-RECOIL START
Hydro
Midsize
ITEM PART NO.
FIGURE 11
DESCRIPTION
QTY
1
2721110CLUTCH-ELECTRIC
(INCLUDES ITEM 2)
1
2
3
4
5
6
7
8
9
2720949 ASSY-CLUTCH WIRE
2722033SWITCH-NEUTRAL
38148
SWITCH-ENGINE STOP
108208
SWITCH DBL POLE NC/NO
148082-10 FUSE 10 AMP
2721505SWITCH-PTO
4166845 HARNESS-MID GEAR DRV
(INCLUDES ITEM 6 & 9)
2722325 RELAY-40 AMP SEALED
1
1
1
1
1
1
1
ITEM PART NO.
DESCRIPTION
QTY
1
49
WIRE DIAGRAM-ELECTRIC START
FIGURE 12
50
Hydro
Midsize
WIRE DIAGRAM-ELECTRIC START
Hydro
Midsize
ITEM PART NO.
FIGURE 12
DESCRIPTION
QTY
1
2721110CLUTCH-ELECTRIC
(INCLUDES ITEM 2)
1
2
3
4
5
6
7
8
2720949 ASSY-CLUTCH WIRE
108208
SWITCH DBL POLE
128010
KEY SWITCH
2308094 SWITCH-NCNC DBL POLE
148082-20 FUSE 20 AMP
2721505SWITCH-PTO
4128561 HARNESS-HYDRO MAIN
(INCLUDES QTY OF 2 OF ITEM 6)
1
1
1
1
2
1
1
ITEM PART NO.
DESCRIPTION
QTY
9 38665SOLENOID-STARTER 1
10*108061-15
CABLE-BATTERY 6.5 RED 1
(FROM STARTER SOLENOID TO STARTER)
11*2722227-03
CABLE-BTTRY W/CONDUIT 1
(FROM (+) POSITIVE BATTERY TERMINAL
TO STARTER SOLENOID)
12*108061-16
CABLE-BTTRY 31.5 BLACK 1
(FROM (-) NEGATIVE BATTERY TERMINAL
TO ENGINE BLOCK)
* NOT ILLUSTRATED
51
WIRING SCHEMATIC-RECOIL START
FIGURE 13
52
REF. 4115548
Hydro
Midsize
Hydro
Midsize
WIRING SCHEMATIC-ELECTRIC START
REF. 4115550
FIGURE 14
53
CUTTERDECK MOUNTING
FIGURE 15
54
Hydro
Midsize
CUTTERDECK MOUNTING
Hydro
Midsize
ITEM PART NO.
1
2
FIGURE 15
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
64263-018 BLT-FLG HD M12-1.75 X 30 4
64246-04 NUT-WHIZ M12-1.75
4
55
HYROGEAR PUMP
FIGURE 16
56
Hydro
Midsize
HYDROGEAR PUMP
Hydro
Midsize
FIGURE 16
4112782 & 4163317
2721615 & 4163316
PUMP-HYDRO RH ILLUSTRATED AS SHOWN
PUMP-HYDRO LH ILLUSTRATED AS SHOWN EXCEPT GROUP A IS ROTATED
180° AROUND THE CENTERLINE OF THE PUMP.
ITEM HYDROGEAR PART NO. PART NO.
DESCRIPTION
QTY
1
70516
2
71615 3
50641
4
50969
5
52629
6
2513027
7
50273
89004101-1340
10
50975
15
2513030
18
70521
19
50315
20
51161
2150951
22
50329
25
70723
29
2003014
30
2003017
31
51246
322003087
34
50551
37
2003005
38
2000015
42A
2510027
42B
2510050
44
70402
49
2513043
56
9005110-4400
66
9005110-3100
100
70525
-----
----
-----
2721615-01
4163316-01
2721615-03
2721615-04
2721615-05
4163316-02
-----
2721615-07
-----
-----
-----
-----
4163316-03
-----
-----
2721615-09
2721615-10
2721615-11
2721615-12
2721615-13
2721615-14
2721615-15
4163316-04
2721615-17
-----
-----
2721615-18
HOUSING KIT
1
END CAP KIT
1
STRAIGHT HEADLESS PIN
2
FLANGE BOLT M8-1.25 X 60 4
HOUSIGN O-RING
1
CHARGE PUMP KIT (STD)
1
STD GEROTOR ASSEMBLY
1
O-RING
1
SOCKET HEAD M6-1/0 X 20
2
BYPASS VALVE KIT (BLANK)
1
PUMP SHAFT KIT
1
BALL BEARING 17 X 40 X 12
1
LIP SEAL 17 x 40 x 12
1
SPACER
1
RETAINING RING
1
CYLINDER BLOCK KIT
1
BLOCK SPRING
1
BLOCK THRUST WASHER
1
VALVE PLATE
1
SWASHPLATE
1
BALL THRUST BEARING
1
TRUNNION ARM
1
SLOT GUIDE
1
CHECK VALVE KIT (.031")
1
CHECK VALVE KIT (BLANK)
1
CHARGE RELIEF VALVE KIT
1
TRUNNION SEAL/RETAINER KIT1
STRAIGHT THREAD PLUG
1
5/16 SAE PLUG
1
OVERHAUL SEAL KIT
1
57
MOUNTING-36" FIXED DECK
Hydro
Midsize
FIGURE 17
45
43
44
42
58
MOUNTING-36" FIXED DECK
Hydro
Midsize
FIGURE 17
ITEM PART NO.
1 112111-02
2 128169
3 4163871.7
4 4124108
52308140
6 2721097
7 2721323
8 2721477
9 2721478
102721479
112721485
12 64123-77
13 64123-265
1438219
15 38524
164115420.7
17 64229-03
184116661
19 4119064.2
20 4147115
21 108074-13
22 4164932.7
23 4121969
24 4135265
25 64006-05
26 64262-012
27 64025-16
28 64123-05
29 64123-139
30 64262-010
31 64123-50
32 64123-88
33 64163-12
3464163-16
35 64163-31
3664163-65
37 64164-12
38 64164-13
39 64209-03
4064221-04
41 64141-4
42 64139-24
43 64141-2
44 64268-03
45 64123-89
DESCRIPTION
QTY
BLADE 18.00 OFFST HLFT
PULLEY, IDLER 5.50
WLDMT-DECK IDLER
S CASTER SUPPORT
PULLEY-ENGINE
S-ASSY SPINDLE 6 LONG
S-ASSY SPINDLE 6 SHORT
BELT-HB 56.75
BELT-HB 85.25
PULLEY-6.75
SPACER-IDLER
BLT-HEX 5/8-18X8 1/2
BLT-HEX HD 5/18-18X7 1/2
SPRING-TENSION
KNOB-4 PRONG 3/8-16
GUIDE-BELT
LOCKNUT-NYLON 3/8-16
PIN-PIVOT
COVER-BELT, 36 FIXED
CHUTE-DECK, 32-54 SD
FLEX TRIM 44.38
BRKT-CHUTE SUPPORT
S-36SDFIXED DK W/ LABS
PULLEY-V IDLER
LOCKWSHR-HELICAL 1/2
BLT-FLG HD 3/8-16 X 1-1/4
NUT-HEX 5/8-18
BLT-HEX 1/2-20X1-1/2
BOLT-3/8-16X4 HEX
BLT-FLG HD 3/8-16 X 3/4
BOLT-HEX 3/8-16X1
BOLT, 3/8-16X2-3/4 HEX
.635/.640X1.0X.25 WASH
WSHR-41/64X1-3/8X12GA
WASHER, 25/64X1X12
WASHER-.890X1.375X18GA
KEY-1/4X1/4X1 SQ END
1/4X1/4X2 SQ KEY
SPRING WASHER.67 ID
E-RING.875
NUT-WLF 3/8-16
BLT-WLF 3/8-16 X 1
NUT-WLF 1/4-20
NUT-FL NYLON LOCK 3/8-16
BLT-HEX 1/4-20X3/4
ITEM PART NO.
DESCRIPTION
QTY
2
1
1
2
2
1
1
1
1
1
1
1
1
1
2
1
16
1
1
1
1
1
1
1
1
12
2
1
1
8
2
1
4
2
1
1
1
1
2
1
10
2
1
2
1
59
MOUNTING-48" FIXED DECK
Hydro
Midsize
FIGURE 18
40
38
39
37
60
MOUNTING-48" FIXED DECK
Hydro
Midsize
FIGURE 18
ITEM PART NO.
1 108074-09
2 112111-01
3128110
4 128169
52188131
6 4124108
72308140
8 2721097
9 2721323
10 2722160
11 2722161
12 64123-77
13 64123-265
14 38524
154110580.7
164116661
17 4147115
18 4119381
19 4119515.2
20 64262-012
21 4164932.7
22 64006-05
23 64025-16
24 64123-05
25 64262-010
26 64123-50
27 64123-88
28 64163-12
29 64163-16
30 64141-4
3164163-65
32 64164-12
33 64164-13
34 64209-03
3564221-04
36 64229-03
37 64139-24
38 64141-2
39 64268-03
40 64123-89
DESCRIPTION
QTY
S CHANNEL-FLEX TRIM 7.12
BLADE 16.25 OFFST HLFT
BELT-CUTTERDECK
PULLEY, IDLER 5.50
SPRING-EXTENSION
S CASTER SUPPORT
PULLEY-ENGINE
S-ASSY SPINDLE 6 LONG
S-ASSY SPINDLE 6 SHORT
BELT-HB 73.00
PULLEY-6.75 EOD
BLT-HEX 5/8-18X8 1/2
BLT-HEX HD 5/18-18X7 1/2
KNOB-4 PRONG 3/8-16
WLDMT-IDLER
PIN-PIVOT
CHUTE-DECK, 32-54 SD
S 48 SD FIXED DK W/LABS
COVER-BELT FIXED 48
BLT-FLG HD 3/8-16 X 1-1/4
BRKT-CHUTE SUPPORT
LOCKWSHR-HELICAL 1/2
NUT-HEX 5/8-18
BLT-HEX 1/2-20X1-1/2
BLT-FLG HD 3/8-16 X 3/4
BOLT-HEX 3/8-16X1
BOLT, 3/8-16X2-3/4 HEX
.635/.640X1.0X.25 WASH
WASHR-41/64X1, 3/8X12GA
NUT-WLF 3/8-16
WASHER-.890X1.375X18GA
KEY-1/4X1/4X1 SQ END
1/4X1/4X2 SQ KEY
SPRING WASHER.67 ID
E-RING.875
LOCKNUT-NYLON 3/8-16
BLT-WLF 3/8-16 X 1
NUT-WLF 1/4-20
NUT-FL NYLON LOCK 3/8-16
BLT-HEX 1/4-20X3/4
ITEM PART NO.
DESCRIPTION
QTY
1
3
1
1
1
2
3
1
2
1
1
1
2
2
1
1
1
1
1
18
1
1
3
1
8
2
1
6
3
10
1
2
1
3
1
21
2
1
2
1
61
MOUNTING-54" FIXED DECK
Hydro
Midsize
FIGURE 19
14
19
10
33
23
11
3
24
34
7
36
35
31
22
4
15
5
23
34
32
20
7
8
9
16
25
1
38
6
39
36
37
42
18
43
36
36
27
30
26
21
41
17
26
28
28
2
29
12
62
29
13
2
40
MOUNTING-54" FIXED DECK
Hydro
Midsize
FIGURE 19
ITEM PART NO.
1 2721512
2 112111-02
3 2188176
4 128169
52188131
6 4124108
72308140
8 2721097
9 2721323
10 2722570
11 2722161
12 64123-77
13 64123-265
14 38524
154110580.7
164116661
17 4147115
18 4128849
19 4129134.2
20 64262-012
21 4164932.7
22 64006-05
23 64025-16
24 64123-05
25 64262-011
26 64123-50
27 64123-88
28 64163-12
29 64163-16
30 64141-4
3164163-65
32 64164-12
33 64164-13
34 64209-03
3564221-04
36 64229-03
37 64123-173
382720685
39 64139-24
40 64141-2
41 64268-03
42 64123-89
DESCRIPTION
QTY
ROLLER-5X2.75 CENTERED
BLADE 18.00 OFFST HLFT
BELT-CUTTERDECK 54
PULLEY, IDLER 5.50
SPRING-EXTENSION
S-CASTER SUPPORT 9 IN.
PULLEY-ENGINE
S-ASSY SPINDLE 6 LONG
S-ASSY SPINDLE 6 SHORT
BELT-HB 75.75
PULLEY-6.75 EOD
BLT-HEX 5/8-18X8 1/2
BLT-HEX HD 5/18-18X7 1/2
KNOB-4 PRONG 3/8-16
WLDMT-IDLER
PIN-PIVOT
CHUTE-DECK, 32-54 SD
S 54 SD CUT DECK W/ LABS
WLDMT-COVER BELT 54
BLT-FLG HD 3/8-16 X 1-1/4
BRKT-CHUTE SUPPORT
LOCKWSHR-HELICAL 1/2
NUT-HEX 5/8-18
BLT-HEX 1/2-20X1-1/2
BLT-FLG HD 3/8-16 X 1
BOLT-HEX 3/8-16X1
BOLT, 3/8-16X2-3/4 HEX
.635/.640X1.0X.25 WASH
WASHR-41/64X1, 3/8X12GA
NUT-WLF 3/8-16
WASHER-.890X1.375X18GA
KEY-1/4X1/4X1 SQ END
1/4X1/4X2 SQ KEY
SPRING WASHER.67 ID
E-RING.875
LOCKNUT-NYLON 3/8-16
BLT-HEX 3/8-16X4-1/2
SPACER-ROLLER
BLT-WLF 3/8-16 X 1
NUT-WLF 1/4-20
NUT-FL NYLON LOCK 3/8-16
BLT-HEX 1/4-20X3/4
ITEM PART NO.
DESCRIPTION
QTY
1
3
1
1
1
2
3
1
2
1
1
1
1
2
1
1
1
1
1
18
1
1
3
1
8
2
1
6
3
10
1
2
1
3
1
22
1
1
2
1
2
1
63
BAFFLES
Hydro
Midsize
FIGURE 20
3
2
4
19
19
3
6
6
7
8
9
11
1
6
16
6
1
10
12
15
16
1
13
14
18
64
17
6
6
20
20
5
20
BAFFLES
Hydro
Midsize
FIGURE 20
ITEM PART NO.
DESCRIPTION
QTY
1
2
64018-2
BLT-CRG 1/4-20X3/4
(NOT USED ON 36" DECKS)
4
64018-3
BLT-CRG 3/8-16X1
(NOT USED ON 48" DECKS)
3
64123-50
BOLT-HEX 3/8-16X1
4 64262-012 BLT-FLG HD 3/8-16 X 1-1/4
QTY USED ON 48" DECK
5 64229-01 LOCKNUT-1/4-20 NYLON
(NOT USED ON 48" & 54" DECKS)
6 64268-03
NUT-FL NYLON LOCK 3/8-16
USED ON 36" DECK ONLY
74115864.7 BAFFLE-DISCHARGE
(USED ON 36", 54" DECK)
8 4120208.7 BAFFLE-DISCHARGE 32-48
(USED ON 48" DECKS ONLY)
9 4165971.7 BAFFLE-48 FRONT LH
(USED ON 48" DECKS ONLY)
10 4165972.7 BAFFLE-FRONT CTR
(USE ON 48" DECKS ONLY)
11 4165965.7 BAFFLE-FRONT LH
(USED ON 54" DECKS ONLY)
12
13
ITEM PART NO.
DESCRIPTION
QTY
1
1
174168515.2 MOUNT-BAFFLE
(USED ON 54" DECK)
4168514.2MOUNT-BAFFLE
(USED ON 48" DECK ONLY)
18 4134343.7 BAFFLE-RIGHT FRONT 36
(USED ON 36" DECK ONLY)
1
2
19 64123-15
BLT-HEX 3/8-16 x 3/4
3
20 64268-01
NUT-FL NYLON LCK 1/4-20
3
1
1
4
6
1
1
1
1
1
4165966.7 BAFFLE-FRONT CTR
1
(USED ON 54" DECKS ONLY)
4168516.7 BAFFLE-RIGHT FRONT
(USED ON 54" DECKS ONLY)
1
14 4168527.7
BAFFLE-RIGHT FRONT
(USED ON 48" DECKS ONLY)
1
15 4147035.7 BAFFLE-FRONT DECK
(USED ON 36" DECKS ONLY)
1
164168523.2 MOUNT-BAFFLE
(QTY 2 ON 48" & 54" DECKS)
2
65
CASTER ASSY-FIXED DECKS
Hydro
Midsize
FIGURE 21
1
2
3
4
5
4
3
6
7
8
10
12
13
9
14
14
15
11
66
16
11
CASTER ASSY-FIXED DECKS
Hydro
Midsize
ITEM PART NO.
1
2
3
4
5
FIGURE 21
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
4124110
ASSY-CASTER 9IN BOBCAT 2
(INCLUDES ITEMS 1-3, 7-12 & 16 QTYs LISTED)
(NOTE 2 ASSYS REQUIRED PER MACHINE)
64173-04 QUICK PIN 64163-07 1-1/32X1-3/4X1/4 WASH 64163-22 1-1/32X1-3/4X1/2 WASHR 4129801
BUSHING-FLANGED 4124108
S CASTER SUPPORT
(INCLUDES ITEMS 4 & 6, QTYs LISTED)
6 85010N
ZERK GREASE FITTING 7 64163-84 WSHR-1.015 X 1.75 X .125
8 2721484.7 WLDMT-CASTER YOKE
9 64229-05 LOCKNUT-NYLON 1/2-13
10 64123-166 BLT-HEX 1/2-13X5-1/2 11 2722591
SPACER-3/4 INCH BRG
122722230-04SPANNER
13 64123-01 BLT-HEX 5/16-24X3/4 14 2722682
BEARING-9" WHEEL
15 4165543
ASSY-9" WHEEL
(INCLUDES ITEM 17)
17* 4165543-01 S-WHEEL HUB ASSY
(INCLUDES ITEMS 13-15 AND HUB ASSY)
1
1
7
2
1
1
1
1
1
1
2
1
4
2
1
1
* NOT ILLUSTRATED
67
SPINDLE ASSEMBLY
FIGURE 22
68
Hydro
Midsize
SPINDLE ASSEMBLY
Hydro
Midsize
ITEM PART NO.
FIGURE 22
DESCRIPTION
QTY
1
2
38348-01 BEARING-SPINDLE SEALED2
33179-02SPINDLE-SHORT
1
(USED IN ITEM 8)
3
33179-01SPINDLE-LONG
(USED IN ITEM 7)
4
5
6
7
2721096 HOUSING-SPINDLE 6 HOLE 1
64144-38 SNAP-RING
1
38315NUT-SPINDLE
1
2721097 ASSY-SPINDLE LONG
1
(INCLUDES ITEMS 1, 3, 4-6)
8
2721323 ASSY-SPINDLE SHORT
(INCLUDES ITEMS 1, 2, 4-6)
ITEM PART NO.
DESCRIPTION
QTY
1
1
69
CUTTERDECK DECALS
FIGURE 23
Hydro
Midsize
6
70
CUTTERDECK DECALS
Hydro
Midsize
ITEM PART NO.
FIGURE 23
DESCRIPTION
QTY
1
2
3
4
4158401 LABEL-BOBCAT, LARGE
1
2000677 LABEL-DANGER/WARNING1
2000572 LABEL-WARNING BLADES 1
2000678 LABEL-ROT PARTS/B-WSHR
QTY FOR 36" DECK
1
QTY FOR 48", 54" DECK
2
5
6
4116761
4164269
ITEM PART NO.
DESCRIPTION
QTY
LABEL-MADE IN USA
1
LABEL-ROTATING BLADES 1
71
WEIGHTS
FIGURE 24
72
Hydro
Midsize
WEIGHTS
Hydro
Midsize
ITEM PART NO.
FIGURE 24
DESCRIPTION
QTY
1
4162891.7WEIGHT
(QTY 10 USED ON 36" DECKS)
(QTY 14 USED ON 48" DECKS)
2
3
64123-100 BOLT-3/8-16X2-1/4 HEX
(USED ON 36" DECKS ONLY)
4
64123-75 BOLT, 3/8-16X3 HEX
(USED ON 48" DECKS ONLY)
4
4
5
64141-4 NUT-WLF 3/8-16
64163-31 WASHER, 25/64X1X12
(USED ON 36" DECKS ONLY)
8
4
ITEM PART NO.
DESCRIPTION
QTY
73
SCHILLER GROUNDS CARE, INC.
ONE BOB-CAT LANE
P.O. BOX 469
JOHNSON CREEK, WI 53038
920-699-2000
www.schillergc.com
©Schiller Grounds Care, Inc. 2010
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement