null  null
* The illustration shows the TD-15.
How to obtain a PDF of the owner’s manual
PDF files of the owner’s manual and supplementary material for this product can be obtained from the
Roland website.
• TD-15/TD-11 Owner’s Manual (this document)
• Data List
(This is not included with the product; you may download it as necessary.)
Visit the following URL, choose “Owner’s Manuals,” and search for the model name “TD-15” or “TD-11.”
http://www.roland.com/support/en/
USING THE UNIT SAFELY
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” (p. 2) and “IMPORTANT NOTES” (p. 4). These sections provide
important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp
of every feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a
convenient reference.
WARNING
Do not disassemble or modify by yourself
Do not open (or modify in any way)
the unit or its AC adaptor.
Do not repair or replace parts by yourself
Do not attempt to repair the unit,
or replace parts within it (except
when this manual provides specific
instructions directing you to do so).
Refer all servicing to your retailer,
the nearest Roland Service Center,
or an authorized Roland distributor,
as listed on the “Information” page.
Do not use or store in the following types of
locations
• Subject to temperature extremes
(e.g., direct sunlight in an
enclosed vehicle, near a heating
duct, on top of heat-generating
equipment); or are
• Damp (e.g., baths, washrooms, on
wet floors); or are
• Exposed to steam or smoke;
or are
• Subject to salt exposure; or are
• Humid; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration
and shakiness.
WARNING
Do not bend the power cord or place heavy
objects on it
This unit should be used only with
a stand that is recommended by
Roland.
Do not excessively twist or bend
the power cord, nor place heavy
objects on it. Doing so can damage
the cord, producing severed
elements and short circuits.
Damaged cords are fire and shock
hazards!
Do not place in an unstable location
When using the unit with a stand
recommended by Roland (MDS
series), the stand must be carefully
placed so it is level and sure to
remain stable. If not using a stand,
you still need to make sure that any
location you choose for placing the
unit provides a level surface that
will properly support the unit, and
keep it from wobbling.
Use only the included AC adaptor and the correct
voltage
Be sure to use only the AC
adaptor included with the unit.
Also, make sure the line voltage
at the installation matches the
input voltage specified on the AC
adaptor’s body. Other AC adaptors
may use a different polarity, or be
designed for a different voltage, so
their use could result in damage,
malfunction, or electric shock.
Use only the included power cord
Use only the attached powersupply cord. Also, the included
power cord must not be used with
any other device.
2
WARNING
Use only Roland stand MDS series that is
recommended
Avoid extended use at high volume
This unit, either alone or in
combination with an amplifier
and headphones or speakers, may
be capable of producing sound
levels that could cause permanent
hearing loss. Do not operate for
a long period of time at a high
volume level, or at a level that is
uncomfortable. If you experience
any hearing loss or ringing in the
ears, you should immediately stop
using the unit, and consult an
audiologist.
Don’t allow foreign objects or liquids to enter
unit; never place containers with liquid on unit
Do not place containers containing
liquid on this product. Never allow
foreign objects (e.g., flammable
objects, coins, wires) or liquids
(e.g., water or juice) to enter this
product. Doing so may cause short
circuits, faulty operation, or other
malfunctions.
USING THE UNIT SAFELY
WARNING
Turn off the unit if an abnormality or malfunction
occurs
Immediately turn the unit off,
remove the AC adaptor from the
outlet, and request servicing by
your retailer, the nearest Roland
Service Center, or an authorized
Roland distributor, as listed on the
“Information” page when:
• The AC adaptor, the powersupply cord, or the plug has been
damaged; or
• If smoke or unusual odor occurs; or
• Objects have fallen into, or liquid
has been spilled onto the unit; or
• The unit has been exposed to rain
(or otherwise has become wet); or
• The unit does not appear to
operate normally or exhibits a
marked change in performance.
Adults must provide supervision in places where
children are present
When using the unit in locations
where children are present, be
careful so no mishandling of the
unit can take place. An adult should
always be on hand to provide
supervision and guidance.
CAUTION
Place in a well ventilated location
The unit and the AC adaptor should
be located so their location or
position does not interfere with
their proper ventilation.
Use only the specified stand (s)
This unit is designed to be used in
combination with specific stands
(MDS series) manufactured by
Roland. If used in combination with
other stands, you risk sustaining
injuries as the result of this product
dropping down or toppling over
due to a lack of stability.
Evaluate safety issues before using stands
Even if you observe the cautions
given in the owner’s manual,
certain types of handling may allow
this product to fall from the stand,
or cause the stand to overturn.
Please be mindful of any safety
issues before using this product.
Grasp the plug when connecting or disconnecting
the AC adaptor
Do not drop or subject to strong impact
Always grasp only the plug on the
AC adaptor cord when plugging
into, or unplugging from, an outlet
or this unit.
Protect the unit from strong impact.
(Do not drop it!)
Periodically clean the AC adaptor’s plug
Do not share an outlet with an unreasonable
number of other devices
Do not force the unit’s powersupply cord to share an outlet with
an unreasonable number of other
devices. Be especially careful when
using extension cords—the total
power used by all devices you have
connected to the extension cord’s
outlet must never exceed the power
rating (watts/amperes) for the
extension cord. Excessive loads can
cause the insulation on the cord to
heat up and eventually melt through.
Do not use overseas
Before using the unit in a foreign
country, consult with your retailer,
the nearest Roland Service Center,
or an authorized Roland distributor,
as listed on the “Information” page.
Do not use a CD-ROM in an audio CD player or
DVD player
At regular intervals, you should
unplug the AC adaptor and clean
it by using a dry cloth to wipe all
dust and other accumulations away
from its prongs. Also, disconnect
the power plug from the power
outlet whenever the unit is to
remain unused for an extended
period of time. Any accumulation of
dust between the power plug and
the power outlet can result in poor
insulation and lead to fire.
CAUTION
Do not connect or disconnect the AC adaptor with
wet hands
Never handle the AC adaptor or
its plugs with wet hands when
plugging into, or unplugging from,
an outlet or this unit.
Disconnect everything before moving the unit
Before moving the unit, disconnect
the AC adaptor and all cords
coming from external devices.
Unplug the AC adaptor from the outlet before
cleaning
Before cleaning the unit, turn it off
and unplug the AC adaptor from
the outlet (p. 10).
If there is a possibility of lightning strike,
disconnect the AC adaptor from the outlet
Whenever you suspect the
possibility of lightning in your area,
disconnect the AC adaptor from
the outlet.
Keep small items out of the reach of children
To prevent accidental ingestion
of the parts listed below, always
keep them out of the reach of small
children.
• Included Parts
Wing bolts (p. 9)
• Removable Parts
Cap of the special connection
cable
Manage cables for safety
Try to prevent cords and cables
from becoming entangled. Also, all
cords and cables should be placed
so they are out of the reach of
children.
Avoid climbing on top of the unit, or placing
heavy objects on it
Never climb on top of, nor place
heavy objects on the unit.
DO NOT play a CD-ROM disc on a
conventional audio CD player. The
resulting sound may be of a level
that could cause permanent hearing
loss. Damage to speakers or other
system components may result.
3
IMPORTANT NOTES
Power Supply
Additional Precautions
• Do not connect this unit to same electrical outlet
that is being used by an electrical appliance that
is controlled by an inverter or a motor (such as a
refrigerator, washing machine, microwave oven, or
air conditioner). Depending on the way in which
the electrical appliance is used, power supply noise
may cause this unit to malfunction or may produce
audible noise. If it is not practical to use a separate
electrical outlet, connect a power supply noise
filter between this unit and the electrical outlet.
• Please be aware that the contents of memory can
be irretrievably lost as a result of a malfunction,
or the improper operation of the unit. To protect
yourself against the risk of loosing important
data, we recommend that you periodically save a
backup copy of important data you have stored in
the unit’s memory to USB flash drives.
• The AC adaptor will begin to generate heat after
long hours of consecutive use. This is normal, and
is not a cause for concern.
• To prevent malfunction and equipment failure,
always make sure to turn off the power on all your
equipment before you make any connections.
• With the factory settings, this unit will
automatically be switched off 30 minutes after
you stop playing or operating the unit. If you don’t
want the unit to turn off automatically, change the
“Auto Off” setting to “OFF” as described on p. 35.
Placement
• Using the unit near power amplifiers (or other
equipment containing large power transformers)
may induce hum. To alleviate the problem, change
the orientation of this unit; or move it farther away
from the source of interference.
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of
such receivers.
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the
vicinity of this unit. Such noise could occur when
receiving or initiating a call, or while conversing.
Should you experience such problems, you should
relocate such wireless devices so they are at a
greater distance from this unit, or switch them off.
• Do not expose the unit to direct sunlight, place
it near devices that radiate heat, leave it inside
an enclosed vehicle, or otherwise subject it to
temperature extremes. Excessive heat can deform
or discolor the unit.
• When moved from one location to another where
the temperature and/or humidity is very different,
water droplets (condensation) may form inside
the unit. Damage or malfunction may result if you
attempt to use the unit in this condition. Therefore,
before using the unit, you must allow it to stand
for several hours, until the condensation has
completely evaporated.
• Do not put anything that contains water on this
unit. Also, avoid the use of insecticides, perfumes,
alcohol, nail polish, spray cans, etc., near the unit.
Swiftly wipe away any liquid that spills on the unit
using a dry, soft cloth.
Maintenance
• For everyday cleaning wipe the unit with a soft,
dry cloth or one that has been slightly dampened
with water. To remove stubborn dirt, use a cloth
impregnated with a mild, non-abrasive detergent.
Afterwards, be sure to wipe the unit thoroughly
with a soft, dry cloth.
• Unfortunately, it may be impossible to restore
the contents of data that was stored in the unit’s
memory or on USB flash drives once it has been
lost. Roland Corporation assumes no liability
concerning such loss of data.
• Use a reasonable amount of care when using the
unit’s buttons, sliders, or other controls; and when
using its jacks and connectors. Rough handling can
lead to malfunctions.
• Never strike or apply strong pressure to the display.
• When disconnecting all cables, grasp the
connector itself—never pull on the cable. This way
you will avoid causing shorts, or damage to the
cable’s internal elements.
• To avoid disturbing others nearby, try to keep the
unit’s volume at reasonable levels. You may prefer
to use headphones, so you do not need to be
concerned about those around you.
• Since sound vibrations can be transmitted through
floors and walls to a greater degree than expected,
take care not to allow such sound to become a
nuisance to others nearby. Although the drum
pads and pedals are designed so there is a minimal
amount of extraneous sound produced when
they’re struck, rubber heads tend to produce
louder sounds compared to mesh heads. You can
effectively reduce much of the unwanted sound
from the pads by switching to mesh heads.
• When you need to transport the unit, package
it in the box (including padding) that it came
in, if possible. Otherwise, you will need to use
equivalent packaging materials.
• Some connection cables contain resistors. Do not
use cables that incorporate resistors for connecting
to this unit. The use of such cables can cause the
sound level to be extremely low, or impossible to
hear. For information on cable specifications, contact
the manufacturer of the cable.
• The explanations in this manual include
illustrations that depict what should typically be
shown by the display.
Note, however, that your unit may incorporate
a newer, enhanced version of the system (e.g.,
includes newer sounds), so what you actually see
in the display may not always match what appears
in the manual.
Before Using External Memories
• Carefully insert the USB flash drives all the way
in—until it is firmly in place.
Top panel
• Do not touch or allow metal to come into
contact with the contact portion of the cards.
• Do not bend, drop, or subject cards to strong
shock or vibration.
• Do not keep cards in direct sunlight, in closed
vehicles, or other such locations.
• Do not allow cards to become wet.
• Do not disassemble or modify the cards.
Handling CDs / DVDs
• Avoid touching or scratching the shiny underside
(encoded surface) of the disc. Damaged or dirty
CD discs may not be read properly. Keep your discs
clean using a commercially available CD cleaner.
About Copyright
• It is forbidden by law to make an audio recording,
video recording, copy or revision of a third party’s
copyrighted work (musical work, video work,
broadcast, live performance, or other work),
whether in whole or in part, and distribute,
sell, lease, perform, or broadcast it without the
permission of the copyright owner.
• Do not use this product for purposes that could
infringe on a copyright held by a third party. We
assume no responsibility whatsoever with regard
to any infringements of third-party copyrights
arising through your use of this product.
• The copyright of content in this product (the
sound waveform data, style data, accompaniment
patterns, phrase data, audio loops and image data)
is reserved by Roland Corporation and/or Atelier
Vision Corporation.
• Purchasers of this product are permitted to
utilize said content for the creating, performing,
recording and distributing original musical works.
• Purchasers of this product are NOT permitted to
extract said content in original or modified form,
for the purpose of distributing recorded medium
of said content or making them available on a
computer network.
• MMP (Moore Microprocessor Portfolio) refers to a
patent portfolio concerned with microprocessor
architecture, which was developed by Technology
Properties Limited (TPL). Roland has licensed this
technology from the TPL Group.
• MPEG Layer-3 audio compression technology
is licensed from Fraunhofer IIS Corporation and
THOMSON Multimedia Corporation.
• Roland, SuperNATURAL, and V-Drums are either
registered trademarks or trademarks of Roland
Corporation in the United States and/or other
countries.
Repairs and Data
4
• To prevent damage to the cards from static
electricity, be sure to discharge any static
electricity from your own body before handling
the cards.
• ASIO is a trademark of Steinberg Media
Technologies GmbH.
• Never use benzine, thinners, alcohol or solvents of
any kind, to avoid the possibility of discoloration
and/or deformation.
• Please be aware that all data contained in the
unit’s memory may be lost when the unit is sent for
repairs. Important data should always be backed
up to USB flash drives, or written down on paper
(when possible). During repairs, due care is taken
to avoid the loss of data. However, in certain cases
(such as when circuitry related to memory itself is
out of order), we regret that it may not be possible
to restore the data, and Roland assumes no liability
concerning such loss of data.
• USB flash drives are constructed using precision
components; handle the USB flash drives carefully,
paying particular note to the following.
• Never touch the terminals of the USB flash drives.
Also, avoid getting the terminals dirty.
• Company names and product names appearing
in this document are registered trademarks or
trademarks of their respective owners.
Copyright © 2012 ROLAND CORPORATION
All rights reserved. No part of this publication may
be reproduced in any form without the written
permission of ROLAND CORPORATION.
Main Features
SuperNATURAL on V-Drums
Roland takes digital drums to a new height with the implementation of its exclusive SuperNATURAL concept. The best
electronic drums in the world just got better.
Improved dynamics and sensitivity make every nuance of playing drums feel even more natural, no matter what your
musical style might be.
What are SuperNATURAL Tones?
Taking advantage of Behavior Modeling Technology, SuperNATURAL is Roland’s exclusive
sound set that achieves a new level of realism and expression that were difficult to realize with
previous sound generators.
Behavior Modeling Technology
Not only physical modeling of the instruments, Roland takes it a step further by modeling the instrument’s distinctive
behavior that responds to how the performer plays, resulting in true-to-life, expressive sounds in realtime.
Enjoy playing with the Internal songs & Song player
Internal songs (p. 26)
Realistic and powerful backing songs and loop phrases are built into the TD.
These are perfect for practicing, or just the pure enjoyment of playing along.
Song player (p. 27)
You can play back audio files (WAV, MP3) directly from an inserted USB flash drive(optional). Also the
Speed Control and A-B repeat functions allow you to take practicing with your favorite songs to a
new level.
Advanced practice support
Coach mode (p. 31)
Roland’s highly acclaimed Coach Mode provides a full set of exercises for self improvement. These
include “Time Check,” “Quiet Count,” and “Warm Ups.”
QUICK REC function (p. 14)
The QUICK REC function is another practice tool that allows you to record and playback your
performance easily.
Using with your computer
USB audio and USB MIDI support (p. 47)
By connecting the TD to your computer with a single USB cable, you can transmit audio and MIDI
data.
Perfect for using with the V-Drums Tutor, V-Drums Friend Jam and/or your own DAW software.
5
Contents
USING THE UNIT SAFELY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Panel Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Side Panel (Connecting Your Equipment). . . . . . . . . . . . . . 8
Top Panel (Connecting Your Equipment). . . . . . . . . . . . . . 9
Bottom Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Getting Ready to Play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Turning the Power On/Off. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Playing the Drums. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Drum Kits and Instruments. . . . . . . . . . . . . . . . . . . . . . . . . . 11
Selecting a Drum Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cross-Stick Function. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Performance Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Metronome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Starting the Metronome. . . . . . . . . . . . . . . . . . . . . . . 13
Changing the Metronome Tempo and Volume. . 13
Recording Your Performance (QUICK REC). . . . . . . . . . . . 14
Quickly Editing an Instrument (QUICK EDIT)
(TD-15 ONLY). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
About the MENU Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Creating a Drum Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Changing the Instrument. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Instrument Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Drum Kit Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using the Effects (FX). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Adjusting the Amount of Ambience for Each
Pad (SEND). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Turning the Multi-Effect On/Off for Each Pad
(SWITCH) (TD-15 ONLY). . . . . . . . . . . . . . . . . . . . . . . . 21
Naming a Drum Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing the MIDI Note Number of Each Pad. . . . . . . . 22
Copying and Pasting a Drum Kit or Pad . . . . . . . . . . . . . . 23
Saving a Drum Kit to a USB Flash Drive. . . . . . . . . . . . . . . 24
Performing Along with a Song. . . . . . . . . . . . . . . . . . . . . . . . 26
Selecting a Song. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Playing the Song. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Changing the Song Settings. . . . . . . . . . . . . . . . . . . . . . . . . 28
Selecting a Folder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Repeatedly Playing a Specified Region (A-B Repeat). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Viewing Song Information. . . . . . . . . . . . . . . . . . . . . 29
Play Along with a Song and Record Your
Performance (QUICK REC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Practicing in Coach Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Selecting a Practice Menu . . . . . . . . . . . . . . . . . . . . . 31
Settings for the Entire TD (SYSTEM). . . . . . . . . . . . . . . . . . . 34
Overall Settings for the TD (Options). . . . . . . . . . . . . . . . . 35
Metronome Setup (Metronome). . . . . . . . . . . . . . . . . . . . . 36
Using a Pad as a Switch (Pad Control) (TD-15 ONLY) . . 36
MIDI-Related Settings (MIDI). . . . . . . . . . . . . . . . . . . . . . . . . 37
Using USB Flash Drive (USB Memory) . . . . . . . . . . . . . . . . 38
Saving Data to a USB Flash Drive (Save Backup). . 38
Loading Data from a USB Flash Drive Back
into the TD (Load Backup) . . . . . . . . . . . . . . . . . . . . . 39
Deleting Data from a USB Flash Drive (Delete Data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Viewing Information About the USB Flash
Drive (Information). . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Formatting a USB Flash Drive (Format). . . . . . . . . 40
Optimizing the Pad Settings (Pad Settings). . . . . . . . . . . 41
Specifying the Type of Pad [F1] (TYPE). . . . . . . . . . 41
Setting the Pad Sensitivity [F2] (BASIC). . . . . . . . . 42
Advanced Settings for the Trigger Parameters
[F3] (ADVNCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Viewing Information About the TD (Information). . . . . . . 46
Restoring the Factory Settings (Factory Reset). . . . . . . . 46
Connecting to Your Computer via USB . . . . . . . . . . . . . . . . 47
Installing the USB Driver. . . . . . . . . . . . . . . . . . . . . . . 47
Connecting the TD to the Computer. . . . . . . . . . . 47
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Saving a Drum Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Loading a Drum Kit from a USB Flash Drive
into the TD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Restoring a Drum Kit to the Factory Settings . . . . . . . . . 25
6
Main Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Panel Descriptions
Front Panel
[F1]–[F3] buttons
(function buttons)
Execute the functions shown in
the bottom of the display.
In this manual, we’ll refer to these
(from the left) as the [F1], [F2], and
[F3] buttons.
Display
[POWER] button
This shows the drum kit name
and other information during
performance. During editing, it
shows the settings as graphics and
text.
Turns the power on/off (p. 10).
* The TD will automatically power-off
approximately 30 minutes (with
the factory settings) after it was last
played or operated.
If you don’t want the power to turn
off automatically, turn the “Auto Off”
setting “OFF” as described in “Auto
Off” (p. 35).
[MENU] button
Accesses the menu screen (p. 16).
Cursor buttons ( / )
[VOLUME] knob
Move the cursor in the screen.
Adjusts the volume that’s output
from the OUTPUT jacks (p. 10).
[EXIT] button
Switches “TUNING,” “MUFFLING,”
and “STRAINER” (p. 15).
Each time you press this button,
you’ll return to the next-highest
level of the screen. If you press it
several times, you will eventually
return to the DRUM KIT screen.
[ ] (METRONOME) button
Value dial
Sounds the metronome (p. 13).
Use this to select drum kits or to
edit values.
[COACH] button
[ ] (QUICK REC) button
Press this when you want to use
the Coach function (p. 31).
Use this when you want to record
your performance (p. 14, p. 30).
[SONG] button
[
[QUICK EDIT] button
Accesses the SONG screen (p.
27). Press this when you want to
play songs or make song-related
settings.
[DRUM KIT] buttons
Switch drum kits (p. 11).
] button
Plays/stops the song or your
performance recorded by QUICK
REC (p. 27, p. 30).
* The illustration shows the TD-15.
How to read this manual
•This owner’s manual applies to both the TD-15 and the TD-11. These two devices will be collectively referred to as the “TD.”
•Functions found only on the TD-15 are indicated by the
icon.
•Buttons on the panel are enclosed by square brackets [ ]; for example, the [SETUP] button.
•Buttons corresponding to function buttons shown in the display are referred to as (for example) the [F3] (XSTICK) button.
7
Panel Descriptions
Side Panel (Connecting Your Equipment)
DC IN jack
Connect the included AC adapter here.
Place the AC adaptor
so the side with the
indicator (see illustration) faces upwards
and the side with
textual information
faces downwards. The indicator will light
when you plug the
AC adaptor into an AC
outlet.
OUTPUT jacks
(L/MONO, R)
For connecting to your audio system or
amp. All sounds from the TD are output
here.
MIDI OUT connector
Use this when you want
to trigger an external MIDI
sound module, sampler,
etc., from the TD (p. 37).
For outputting sounds in MONO, connect
the cable to the L/MONO jack.
* The illustration shows the TD-15.
[VOLUME] knob
Adjusts the volume of the
headphones.
PHONES jack
MIX IN jack
Connect stereo
headphones here.
Sound will still be output
from the OUTPUT jacks
even if headphones are
connected.
By connecting your
audio player or other
audio source via a stereo
mini-plug, you can enjoy
playing the drum along
with your favorite songs.
TRIGGER IN jacks
(CRASH2, AUX
)
These allow you to connect
additional pads.
* The volume will be determined by
connected device.
NOTE
• To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any
connections.
• When connection cables with resistors are used, the volume level of equipment connected to the MIX IN jack may be low. If
this happens, use connection cables that do not contain resistors.
8
Panel Descriptions
Top Panel (Connecting Your Equipment)
COMPUTER port
MEMORY port
Use a USB cable to connect the TD
to your computer (p. 47). MIDI data
and audio data can be sent via USB
to and from your DAW software.
You can connect your USB flash drive
(separately sold) here, and play back
audio files from it (p. 27) or save TD
settings on it (p. 38).
NOTE
• Use USB flash drive sold by Roland. We
cannot guarantee operation if other products
are used.
• Never insert or remove a USB flash drive while
this unit is turned on. Doing so may corrupt
the unit’s data or the data on the USB flash
drive.
• Carefully insert the USB flash drive all the way
in-until it is firmly in place.
• Do not unplug USB flash drive from the TD while the USB flash
drive access indicator is blinking. Doing so may damage the USB
flash drive or the data.
Bottom Panel
TRIGGER INPUT
connector
Connect the included
dedicated cable to this
connector, and use it to
connect the pads and
pedals.
Sound module mounting plate attachment
holes
Attach the included sound module mounting plate
here to attach the TD to your drum stand.
Use the included wing bolts to attach the plate as
shown in the illustration.
* Use only the included wing bolts. Using any other
bolts will cause malfunctions.
* The TD must be attached to the sound module
mounting plate when in use.
To prevent the inadvertent disruption of power
to your unit (should the plug be pulled out
accidentally), and to avoid applying undue stress
to the DC IN jack, anchor the power cord using the
cord hook, as shown in the illustration.
NOTE
When turning the unit upside down, be sure to handle the unit with care so as to prevent damage to the buttons, knobs,
etc.
9
Getting Ready to Play
Turning the Power On/Off
Turning the power off
NOTE
Turning the power on
941
* Once everything is properly connected (p. 8), be sure
to follow the procedure below to turn on their power.
If you turn on equipment in the wrong order, you risk
causing malfunction or equipment failure.
943
* Before turning the unit on/off, always be sure to turn
the volume down. Even with the volume turned
down, you might hear some sound when switching
the unit on/off. However, this is normal and does not
indicate a malfunction.
Settings you’ve edited on the TD itself will be saved
when you turn off the power. Be sure to turn off the
power by pressing the [POWER] button.
1. Minimize the volume of the TD and of the
external equipment connected to the TD.
2. Power-off the external equipment.
3. Hold down the [POWER] button until the screen
indicates “See you!”
1. Turn the [VOLUME] knob all the way to the left to
minimize the volume.
If you’re using headphones, you should also minimize
the [VOLUME] knob located on the side panel.
2. Minimize the volume of the connected amp or
audio system.
3. Press the [POWER] button.
942
* This unit is equipped with a protection circuit. A brief
interval (a few seconds) after turning the unit on is
required before it will operate normally.
4. Power-on the amp or audio system that’s
connected to the TD.
5. While striking the pads to hear the sound, adjust
the volume by gradually turning the [VOLUME]
knob toward the right.
Also adjust the volume appropriately on the connected
amp or audio system.
If you’re using headphones, you should also minimize
the [VOLUME] knob located on the side panel.
If you don’t want the power to turn off automatically, change the “Auto Off” setting to “OFF.”
309
The TD will automatically power-off approximately 30 minutes (with the factory settings) after it was last played or
operated.
If you don’t want the power to turn off automatically, turn the “Auto Off” setting “OFF” as described on p. 35.
10
Playing the Drums
Drum Kits and Instruments
Selecting a Drum Kit
On the TD, the sound you hear when you strike each pad
is called an “instrument.” A “drum kit” is a set of sounds
(instruments) assigned to the pads.
Drum kit
1. Use the [DRUM KIT] buttons to select a drum kit.
Instrument
The DRUM KIT screen will appear.
The illustration below shows the structure of a drum kit.
No matter what screen is in use, by pressing the [DRUM
KIT] button, you will return to the DRUM KIT screen.
Selecting a drum kit from the list
Drum kit 100 (50 on the TD-11)
In the DRUM KIT screen, you can turn the value dial to
access the KIT LIST and select a drum kit from the list.
Drum kit 1
About the DRUM KIT screen
Pad settings
KICK
SNARE
Head
TOM3
TOM1
TOM2
Head
Head
Head
Rim
Rim
Rim
HI-HAT
CRASH1
This is the TD’s main screen; it will appear when you press
a [DRUM KIT] button.
Drum kit number
CRASH2
Head
Bow
Bow
Bow
Rim
Edge
Edge
Edge
Strength of the pad strike
Drum kit
name
RIDE
Bow
AUX
Edge
Head
Bell
Rim
Sub title
Instrument settings
Instruments (instrumental sounds),
EDIT (tuning, volume, etc.)
Cross-Stick Function
Ambience send level
MIDI settings
Pressing the [F3] (XSTICK) button enables or disables the
ability to play the cross-stick sound (p. 12) on the rim of the
snare pad.
Ambience settings
The performance location, wall material, amount of
ambience, etc.
Multi-effect settings
Equalizer settings
Overall settings for the entire drum kit
Volume, drum kit name
* The [F3] (XSTICK) button is shown only if cross-stick
is enabled.
What do Head and Rim mean?
Head
Rim
On the TD, settings for a pad’s
head and rim (for a cymbal, the
bow and edge) can be made
separately.
11
Playing the Drums
Performance Techniques
Pads (such as PDX-100/PDX-8/PDX-6)
Cymbals (such as CY-13R/CY-8)
Bow shot
The most common method, playing the middle area of
the cymbal.
Head shot
Hit only the head of the pad.
Edge shot
Head
Use the shoulder of the stick to hit the edge sensor of the
cymbal pad (as shown in the figure).
Rim shot
Strike the head and the rim of the pad simultaneously.
A sound (rim sound) different than the head shot will be
heard.
Edge sensor
Bell shot (CY-15R, CY-13R)
Strike the bell area.
Rim
Cross stick
When XSTICK (p. 11) is on:
Only strike the rim of the pad.
Depending on the sound assigned to the rim you can
play rim shots and/or cross stick sounds.
* Strike the bell somewhat strongly with the shoulder
of the stick.
Choking a cymbal
Rim
Rim
* This is supported only for the snare pad.
* To play the cross stick, be sure that you only strike the
rim of the pad. Place your hand on the head gently,
otherwise this may prevent the cross stick function
from working properly.
12
Choking (pinching) the cymbal’s edge with the hand
immediately after hitting the cymbal will mute or
choke the sound, just like with a real cymbal. The Choke
function only works when you grasp in the area (where
the edge sensor is) as shown in the figure. If you do
otherwise, it will not work.
Roland logo
Edge sensor
Playing the Drums
Hi-Hat (CY-5/VH-11)
Open/Closed
The hi-hat sound will change smoothly between open
and closed depending on pressure applied to the hi-hat
control pedal or a hi-hat stand.
Foot closed and foot splash sounds are possible.
Using the Metronome
Practicing with the metronome is the best way to
develop accurate timing.
Starting the Metronome
1. Press the [
] button.
The metronome will start playing, and the button will
blink in time with the tempo.
MEMO
You can change the way in which the metronome
sounds (p. 36).
Bow shot
Hit the striking surface of the hi-hat.
Changing the Metronome Tempo
and Volume
1. In the DRUM KIT screen (p. 11), press the [F1]
(TEMPO) button.
Bow
The METRONOME screen will appear.
Edge shot
Use the shoulder of the stick to hit the edge of the hi-hat
pad.
2. Use the [F1]–[F3] buttons to select the item that
you want to edit, and use the value dial to edit
the setting.
Edge
Button
Value
Description
Use the value dial to set the
tempo.
* You can set the tempo by
pressing the [F1] (TEMPO)
button three or more times
in succession at the desired
interval.
[F1]
(TEMPO)
20–260
[F2]
(VOLUME)
0–10
[F3] (SETUP)
Accesses the METRONOME SETUP screen (p. 36).
Use the value dial to set the
volume.
13
Playing the Drums
Recording Your Performance
(QUICK REC)
The TD lets you easily record and play back your own
performance (QUICK REC).
This is a convenient way to repeatedly record
yourself practicing and then play back to check your
performance.
* Before you continue, select the drum kit that you
want to use for practicing (recording).
MEMO
You can also record your playing along with a song.
For details, refer to p. 30.
1. In the DRUM KIT screen (p. 11), press the [
REC) button.
] (QUICK
The [ ] (QUICK REC) button will light, and the QUICK REC
screen will appear.
Where the recorded data is exported
When a USB flash drive is connected,
your recorded data is automatically
exported to the USB flash drive. Only the
five most recent recorded performances
will be exported as SMF data.
MEMO
SMF (Standard MIDI File) is a standard file
format that allows performance data to
be exchanged between various musical
applications.
The recorded data is saved in the following folder
of the USB flash drive.
Roland
TD-15 or TD-11
Backup
Kit
QUICK REC
MEMO
If you want to hear the metronome while you record,
press the [ ] button to turn on the metronome.
Use the value dial to set the tempo.
2. To start recording, strike a pad or press the
[
] button.
* When recording starts, the previous recording will be
completely erased.
3. Press the [
4. Press the [
] button to stop recording.
] button once again.
The recorded performance will play back.
You can press the [F2] (REPEAT)
button to make the performance
play back repeatedly.
5. Press the [
14
] button to stop playback.
KIT_01.MID
KIT_02.MID
KIT_03.MID
KIT_04.MID
KIT_05.MID
Quickly Editing an Instrument (QUICK EDIT)
The TD-15’s QUICK EDIT function lets you make quick and easy adjustments to the sound of each instrument.
1. Before you continue, select the drum kit that contains the instrument you want to edit.
2. In the DRUM KIT screen (p. 11), press the [QUICK EDIT] button.
Each time you press the button, you’ll cycle between “Tuning,” “Muffling,” and “Strainer,” and then return to the DRUM KIT
screen.
The pad being edited
3. Strike the pad whose instrument you want to edit.
The screen will show the edit screen for the pad you struck.
4. Use the value dial to edit the value.
Parameter
Value
Description
Tuning
-240–+240
Negative (-) settings will lower the pitch, and positive (+) settings will raise the pitch.
Muffling
0–50
Larger values will reduce the resonance and emphasize the attack.
Strainer
1–10
Strainer (snare) tension. Higher values make the tension tighter.
Snare Buzz
0–10
Resonance of the snare. Higher values increase the resonance.
* The editable parameters will differ depending on the instrument group.
5. Press the [EXIT] button to return to the DRUM KIT screen.
15
About the MENU Screens
There are eight menu screens that allow you to edit the drum kit.
In the DRUM KIT screen, press the [MENU] button to access the KIT MENU screen, from which you can jump to each edit screen.
INST
Here you can edit the instrument (p. 17).
Menu
Description
Page
Inst Edit
Instrument settings
p. 18
Kit Vol
Drum kit volume settings
p. 18
FX
Apply an effect to the entire drum kit (p. 19).
Menu
Description
Page
Ambience
Ambience settings
p. 20
Multi-effect settings
p. 20
EQ settings
p. 20
Multi-FX
EQ
NAME
Assign a name to the drum kit (p. 22)
MIDI
Change the MIDI note number of each pad (p. 22).
COPY/PASTE
Copy and paste drum kits or pads (p. 23).
SAVE/LOAD
Save a drum kit to your USB flash drive, or load a previously-saved drum kit
from the USB flash drive back into the TD (p. 24).
1 KIT RESTORE
This lets you return the currently selected drum kit to the factory settings
(p. 25).
Use the cursor buttons (
to scroll the screen.
SYSTEM
Here you can edit settings that apply to the entire TD (p. 34).
Menu
Description
Page
Options
Settings for display contrast and power
(Auto Off )
p. 35
Metronome
Metronome settings
p. 36
Settings for the pads connected to the
TRIGGER IN AUX jacks
p. 36
p. 37
Pad Control
16
MIDI
MIDI-related settings
USB Memory
Use a USB flash drive
p. 38
Pad Settings
Pad settings
p. 41
Information
View information about the TD itself
p. 46
Factory Reset
Restore the factory settings
p. 46
/
)
Creating a Drum Kit
You can edit the individual sounds in each kit to
customize them for your musical style.
Changing the Instrument
On the TD, each instrumental sound, such as the kick
drum or snare drum within the drum kit, is called an
“instrument (INST).”
1. In the DRUM KIT screen (p. 11), press the [MENU]
Individual head and rim settings (Link)
For some pads, you can assign different instruments to
the head and rim (for a cymbal, to the bow and the bell).
To enable this, turn Link off.
1. In the INST screen, press the [F1] (LINK) button.
Each time you press the button, LINK will turn on/off.
Value
Description
ON
For SNARE, TOM1–3, HIHAT, CRASH1–2, RIDE,
and AUX (TD-15 only), the head and rim
settings (instrument, tuning, muffling, pad
volume, pan) will change in tandem.
OFF
For SNARE, TOM1–3, HIHAT, CRASH1–2, RIDE,
and AUX (TD-15 only), the head and rim
settings can be changed independently.
button.
The KIT MENU screen will appear.
Previewing (auditioning) an instrument
2. Press the [F1] (INST) button.
When the INST screen is displayed, you can strike the
pad or press the [F3] (PREVIEW) button to preview the
selected instrument.
The INST screen will appear.
Instrument type (instrument group)
Instrument
Instrument
number
Pad name
3. Strike the pad whose instrument you want to
change.
The edit screen for the pad you struck will appear.
MEMO
Alternatively, you can use the cursor buttons ( / ) to
move the cursor to the pad name, and then use the
value dial to select a pad.
4. Use the cursor buttons (
/ ) to move the cursor
to the desired instrument group or instrument.
5. Use the value dial to change the instrument
group or instrument.
6. Press the [EXIT] button to return to the DRUM
KIT screen.
17
Creating a Drum Kit
Instrument Edit
Parameter
1. In the DRUM KIT screen (p. 11), press the [MENU]
button.
Fixed HH
Value
Description
NORMAL
The openness
of the hi-hat can
be changed by
the pedal.
FIXED
The openness of
the hi-hat will be
fixed.
NORMAL,
FIXED1–4
The KIT MENU screen will appear.
2. Press the [F1] (INST) button.
Tone Color
-50–+50
Adjusts the brightness of the
tone. Positive (+) values make
the tone brighter; negative (-)
values make the tone darker.
want to edit.
Volume
0–100
Specifies the volume.
The edit screen for the pad you struck will appear.
Pan
L15–CENTER–R15
Specifies the pan (stereo
position).
The INST screen will appear.
3. Strike the pad whose instrument settings you
4. Press the [F2] (EDIT) button.
The INST EDIT screen will appear.
Drum Kit Volume
1. In the INST EDIT screen, press the [F3] (KIT VOL)
button.
The KIT VOLUME screen will appear.
5. Use the cursor buttons (
parameter.
/ ) to select a
6. Use the value dial to edit the value of that
parameter.
For details on the parameters that can be edited, refer to
“INST EDIT parameter list” below.
7. Press the [EXIT] button to return to the DRUM
KIT screen.
parameter.
/ ) to select a
3. Use the value dial to edit the value of that
INST EDIT parameter list
* The editable parameters will differ depending on the
instrument group.
18
2. Use the cursor buttons (
Parameter
Value
Description
Tuning
-240–+240
Negative (-) values will lower
the pitch, and positive (+)
values will raise the pitch.
Muffling
0–50
Larger values will decrease
the resonance, emphasizing
the attack of the sound.
Snare Buzz
0–10
Higher values will make the
snare resonance louder.
Strainer
1–10
Higher values make the
strainer (snare) tension
tighter.
parameter.
Parameter
Value
Description
Kit Volume
0–100
Overall drum kit volume
Pedal HH
Volume
0–100
Pedal hi-hat volume
Xstick
Volume
0–100
Cross-stick volume
4. Press the [EXIT] button several times to return to
the DRUM KIT screen.
Creating a Drum Kit
Using the Effects (FX)
How each effect works
AMBIENCE
This produces an ambience (room reverberation) that’s ideal for drum sounds.
You can adjust the room ambience (the type and size of the room) and the reverb
(reverberation).
MULTI-FX
This is a powerful multi-effect that can be used to transform your sound.
You can use it to distort the sound, or give it depth and spaciousness.
EQ
This is a four-band (low, two mid bands, high) equalizer.
Use it to adjust the tonal character.
Basic procedure
The edit screen for the selected effect will appear.
1. In the DRUM KIT screen (p. 11), press the [MENU]
Use the cursor buttons ( /
) to select a parameter.
button.
Use the value dial to
edit the value.
The KIT MENU screen will appear.
2. Press the [F2] (FX) button.
The FX screen will appear.
3. Press a function button to select the item that
you want to edit.
[F1] (AMBIENCE)
Ambience
[F2] (MULTI-FX)
Multi-effect
[F3] (EQ)
Equalizer
Use the [F1]–[F3] buttons to switch
tabs (screens).
* The MULTI-FX function is provided only on the TD-15.
4. Press the [EXIT] button several times to return to
the DRUM KIT screen.
19
Creating a Drum Kit
FX parameter list
Parameter
Value
Description
Type
10 types
Type of ambience
Character
1–7
Character of the ambience sound
Size
TINY, SMALL, MEDIUM,
LARGE, HUGE
Size of the room
Wall Type
CURTAIN, CLOTH, WOOD, PLASTER, CONCRETE,
GLASS
Material of the walls
Shape
0–100
Width of the room
Level
0–100
Overall amount of ambience
Ambience Send
0–100
Amount sent from each pad to the ambience
0–100
Amount sent from the multi-effect to the ambience
[F1] (AMB)
MFX to Ambi Send
[F2]
Type of multi-effect
Type
10 types
For details on multi-effect’s parameters, download “Data List” (PDF file) from “TD-15” in
the “Owner’s Manuals” list on the Roland website (http://www.roland.com/support/en/).
[F3] (EQ)
20
High Freq
1 kHz–8 kHz
Frequency of the high region
High Gain
-12 dB–+12 dB
Amount of boost/cut for the high region
Low Freq
20 Hz–1 kHz
Frequency of the low region
Low Gain
-12 dB–+12 dB
Amount of boost/cut for the low region
Mid1 Freq
20 Hz–8 kHz
Frequency of the mid-1 region
Mid1 Q
0.5, 1.0, 2.0, 4.0, 8.0
Mid1 Gain
-12 dB–+12 dB
Amount of boost/cut for the mid-1 region
Mid2 Freq
20 Hz–8 kHz
Frequency of the mid-2 region
Mid2 Q
0.5, 1.0, 2.0, 4.0, 8.0
Mid2 Gain
-12 dB–+12 dB
Width of the mid-1 region
Larger values make the width more narrow.
Width of the mid-2 region
Larger values make the width more narrow.
Amount of boost/cut for the mid-2 region
Creating a Drum Kit
Adjusting the Amount of
Ambience for Each Pad (SEND)
You can adjust the amount of ambience (the send level)
for each pad.
1. Access the AMBIENCE screen as described in
steps 1–3 of the basic procedure (p. 19).
2. Press the [F3] (SEND) button.
The AMBIENCE SEND screen will appear.
3. Press the [F1] (LINK) button to turn Link on/off.
4. Select a pad, either by striking that pad or by
pressing the [F2] ( ) or [F3] ( ) buttons.
The cursor will move to the pad you selected.
Link icon
5. Use the value dial to specify the amount of
ambience (send level).
Value
0–100
6. Press the [EXIT] button several times to return to
the DRUM KIT screen.
Turning the Multi-Effect On/Off for
Each Pad (SWITCH)
You can specify whether the multi-effect will be applied
to each pad (on) or not applied (off ).
1. Access the MULTI-FX screen as described in steps
1–3 of the basic procedure (p. 19).
2. Press the [F3] (SWITCH) button.
The MULTI-FX SWITCH screen will appear.
3. Press the [F1] (LINK) button to turn Link on/off.
4. Select a pad, either by striking that pad or by
pressing the [F2] ( ) or [F3] ( ) buttons.
The cursor will move to the pad you selected.
For details on the screen, refer to the explanation of the
AMBIENCE SEND screen (p. 21).
Move the cursor within the screen.
If you press the [F1] (LINK) button to make the Link icon
light (on), the parameters of the head and rim (for a
cymbal, the bow and edge; for a ride cymbal, the bow,
edge, and bell) can be edited simultaneously.
5. Use the value dial to turn the effect on/off.
6. Press the [EXIT] button several times to return to
the DRUM KIT screen.
If this is off, each can be set independently.
Indication in the
screen
Pad
K
Kick
S
Snare
T1–T3
Tom 1–3
HH
Hi-hat
C1, C2
Crash 1, 2
RD
Ride
AUX
MFX
Pad connected to the AUX jack
Ambience send amount from MFX
21
Creating a Drum Kit
Naming a Drum Kit
You can assign a name of up to 12 characters to each
drum kit.
You can also assign a sub title of up to 14 characters
below the kit to indicate the musical style or the date on
which you created the kit.
1. In the DRUM KIT screen (p. 11), press the [MENU]
button.
The KIT MENU screen will appear.
Changing the MIDI Note
Number of Each Pad
Here’s how to change the MIDI note number that is
transmitted and received by each pad.
MEMO
The settings in this screen will be ignored if the
SYSTEM menu setting “Std MIDI Setup Lock” is “ON”
(p. 37).
1. In the DRUM KIT screen (p. 11), press the [MENU]
2. Press the [F3] (NAME) button.
button.
The KIT NAME screen will appear.
The KIT MENU screen will appear.
Drum kit name
Sub title
2. Press the cursor buttons (
/ ) or the [MENU]
button to scroll the screen, and press the [F1]
(MIDI) button.
The MIDI NOTE NUMBER screen will appear.
3. Strike the pad whose settings you want to
change.
3. Press the [F1] (
) or [F2] ( ) button to move the
cursor to the character that you want to change.
4. Use the value dial to change the character.
You can delete or insert a character by holding down
the [F3] (DEL/INS) button and pressing the [F1] or [F2]
button.
Button
Description
[F3]+
[F1] (DELETE)
Deletes the character at the cursor
position; subsequent characters will
move one place to the left.
[F3]+
[F2] (INSERT)
Inserts a space at the cursor position;
subsequent characters will move one
place to the right.
5. Press the [EXIT] button several times to return to
the DRUM KIT screen.
The edit screen of the pad you struck will appear.
MEMO
You can also select a pad by using the cursor buttons
( / ).
Press the [F2] ( ) or [F3] ( ) buttons to select the head/
rim (bow/edge/bell) of each pad.
4. Use the value dial to edit the value.
Value
0–127, OFF
* If the same note number as another pad is selected,
an “*” is shown at the right of the note number.
5. Press the [EXIT] button several times to return to
the DRUM KIT screen.
22
Creating a Drum Kit
Copying and Pasting a Drum
Kit or Pad
3. Press the [F1] (SEL) button to specify whether
you want to copy a drum kit or a pad.
When copying a drum kit
Drum kit name
You can copy the settings of a drum kit or pad, and paste
them to another kit or pad.
NOTE
When you execute the paste operation, the contents
of the paste-destination will be erased. Use this
operation with caution.
When copying a pad
The contents that are copied
Pad name
For a drum kit
Copied settings
Remarks
Settings for the entire
drum kit
Volume, drum kit name
Ambience settings
On/off, performance location,
wall material, amount, etc.
Equalizer settings
High/low adjustment
4. Use the value dial to select the drum kit or pad
that you want to copy.
MFX settings
Settings for each pad
—
Instrument, INST EDIT parameters, MIDI note numbers
For a pad
Copied settings
Remarks
Instrument settings
Instrument, INST EDIT parameters
* Effect settings and MIDI note numbers are not
copied.
MEMO
• You can also strike a pad to audition the drum kit or
pad that you’re copying.
• When copying and pasting a pad, you can also switch
the drum kit. Use the cursor buttons ( / ) to move
the cursor to the drum kit name, and use the value
dial to change drum kits.
5. Press the [F2] (COPY) button.
The contents of the drum kit or pad will be copied to the
clipboard.
6. Use the value dial to select the paste-destination
drum kit or pad.
MEMO
1. In the DRUM KIT screen (p. 11), press the [MENU]
button.
The instrument settings of both the head and rim will
be copied at the same time.
The KIT MENU screen will appear.
2. Press the cursor buttons (
/ ) or the [MENU]
button to scroll the screen, and press the [F2]
(COPY/PASTE) button.
The COPY/PASTE screen will appear.
23
Creating a Drum Kit
7. Press the [F3] (PASTE) button.
If you’re pasting a pad, the paste operation will occur at
this point.
If you’re pasting a drum kit, a confirmation screen will
appear.
Saving a Drum Kit to a USB
Flash Drive
Here’s how you can save a drum kit to your USB flash
drive.
Saving a Drum Kit
* If you decide to cancel, press [F1] (CANCEL).
8. Press the [F3] (OK) button.
The contents of the clipboard will be overwritten onto
the paste-destination.
9. Press the [EXIT] button several times to return to
the DRUM KIT screen.
1. Connect your USB flash drive (p. 9).
2. Make sure that the drum kit you want to save is
selected.
3. In the DRUM KIT screen (p. 11), press the [MENU]
button.
The KIT MENU screen will appear.
4. Press the cursor buttons (
/ ) or the [MENU]
button to scroll the screen, and press the [F3]
(SAVE/LOAD) button.
The 1 KIT SAVE/LOAD screen will appear.
5. Press the [F1] (SAVE) button.
The 1 KIT SAVE screen will appear.
6. Use the cursor buttons (
/ ) or the value dial to
specify the save-destination.
7. Press the [F3] (SAVE) button.
* If data already exists at the save-destination, a
confirmation screen will appear.
Press the [F3] (OK) button to execute the save
operation. If you decide to cancel, press the [F1]
(CANCEL) button.
The drum kit you selected in step 2 will be saved to your
USB flash drive.
When the data has been saved, the screen will indicate
“Completed.”
8. Press the [EXIT] button several times to return to
24
the DRUM KIT screen.
Creating a Drum Kit
Loading a Drum Kit from a USB
Flash Drive into the TD
1. Connect your USB flash drive (p. 9).
2. Make sure that the loading-destination drum kit
is selected.
3. In the DRUM KIT screen (p. 11), press the [MENU]
button.
The KIT MENU screen will appear.
4. Press the cursor buttons (
/ ) or the [MENU]
button to scroll the screen, and press the [F3]
(SAVE/LOAD) button.
The 1 KIT SAVE/LOAD screen will appear.
5. Press the [F3] (LOAD) button.
The 1 KIT LOAD screen will appear.
Restoring a Drum Kit to the
Factory Settings
Here’s how the currently selected drum kit can be
restored to its factory-set state.
An accidentally-overwritten drum kit can also be
restored by this operation.
NOTE
The currently selected drum kit will be overwritten.
1. Make sure that you’ve selected the drum kit that
you want to restore to its original state.
2. In the DRUM KIT screen (p. 11), press the [MENU]
button.
The KIT MENU screen will appear.
3. Press the cursor buttons (
/ ) or the [MENU]
button to scroll the screen, and press the [F1]
(1 KIT RESTORE) button.
The 1 KIT RESTORE screen will appear, and a list of the
factory-set drum kits will be shown.
6. Use the cursor buttons (
/ ) or the value dial to
select the drum kit that you want to load.
7. Press the [F3] (LOAD) button.
A confirmation screen will appear.
4. Use the cursor buttons (
/ ) or the value dial to
select the desired drum kit.
5. Press the [F3] (RESTORE) button.
A confirmation screen will appear.
* If you decide to cancel, press the [F1] (CANCEL)
button.
8. Press the [F3] (OK) button.
The drum kit from the USB flash drive will be overwritten
onto the drum kit you selected in step 2.
When loading is finished, the screen will indicate
“Completed.”
9. Press the [EXIT] button several times to return to
the DRUM KIT screen.
* If you decide to cancel, press the [F1] (CANCEL)
button.
6. Press the [F3] (OK) button.
When the data has been restored, the screen will indicate
“Completed.”
7. Press the [EXIT] button several times to return to
the DRUM KIT screen.
25
Performing Along with a Song
The TD contains built-in-songs and phrases covering a
variety of styles selected for enhancing your practice
time. You can play the drums while listening to one of
these songs.
If a USB flash drive is connected, you can play the drums
while listening to one of your favorite songs from the
USB flash drive.
Song structure
Audio files that can be played by the TD
You can play back audio files of the following formats
from a USB flash drive.
MP3
Sampling rate
44.1 kHz
Bit rates
64 kbps–320 kbps
WAV
A song contains MP3 or WAV audio tracks and drum
tracks (MIDI data) containing a drum performance.
For some internal songs there is a guide drum part on its
drum track, which you can mute in order to play along
with the song.
You can also use the QUICK REC function to record your
performance with the songs.
After doing so, when playing them back you can mute
the drum part you have recorded.
Song
Sampling rate
44.1 kHz
Bit depth
8, 16, 24-bit
When transferring files from your
computer to a USB flash drive
Audio files can be played back not only from the root
level (top level) of the USB flash drive, but also from
within a folder.
For details on how to select a folder, refer to “Selecting a
Folder” (p. 28).
Audio track
* The file name will be the song name.
Drum track
* Use only single-byte alphanumeric characters in the
file name.
* File names containing more than 14 characters
or containing double-byte characters will not be
displayed correctly.
* You can put up to 100 song files in a single folder.
* Make sure that no single file is larger than 2 GB.
This button is shown if the song
contains drum data.
* The song’s performance data is not transmitted from
the MIDI OUT connector.
26
Performing Along with a Song
Selecting a Song
Playing the Song
If you want to select a song from a USB flash drive, you
must first connect the USB flash drive to the TD (p. 9).
NOTE
1. Use the following buttons to play back the song.
Button
If you have recorded your drum performance along
with a song, this data will be lost when changing
songs.
Function
]
[
Play/stop song
[F1] (
)
[F2] (
)
1. Press the [SONG] button.
Selects the previous song.
Hold down to rewind the song. (*)
Selects the next song.
The button will light, and the SONG screen will appear.
[F3] (DRUM)
Hold down to fast-forward the song. (*)
Drum track on/off
(*) You can’t fast-forward or rewind a song that contains a drum
track.
2. To stop, press the [
Use the cursor buttons ( / ) to switch between internal
songs (Internal) and songs (or folder names) on the USB
flash drive.
For details on how to select a folder, refer to
“Selecting a Folder” (p. 28).
buttons to select a song.
)/[F2] (
] button.
] button will go dark, and song playback will
MEMO
• In the DRUM KIT screen, you can hold down the
[SONG] button and press the [
] button to play/
stop the song.
MEMO
2. Use the value dial or the [F1] (
The [
stop.
)
• If you press the [SONG]/[EXIT]/[DRUM KIT] button,
you will return to the DRUM KIT screen but the song
will continue playing.
This symbol is shown while the
song is playing.
About the SONG screen
Song name
Song number
This is the name of
the currently selected
song.
This is the number of
the currently selected
song.
Elapsed time
Song playback
speed (p. 28)
Loop on/off
(p. 28)
Song playback
position
27
Performing Along with a Song
Changing the Song Settings
Selecting a Folder
1. In the SONG screen, press the [MENU] button.
1. In the SONG MENU screen, press the [F2]
The SONG MENU screen will appear.
(FOLDER) button.
The FOLDER SELECTION screen will appear.
2. Use the cursor buttons (
/ ) or the [MENU]
button to scroll the screen.
3. Press the [F1]–[F3] buttons to select the menu
item whose settings you want to change, and
use the value dial to edit the value.
Button
Value
Description
[F1] (VOLUME)
0–100
Song volume
80–120 %
Song playback tempo
(*)
[F2] (SPEED)
Specifies the repeat playback setting (p. 29).
[F3] (A-B)
If you press this while making the setting,
repeat playback will be turned off.
(*)
ON
[F1] (LOOP)
OFF
When the song has
played back to the end,
playback will return to
the beginning of the
song and continue.
Playback will stop
when the song has
played back to the end.
[F2] (FOLDER)
Selects a folder within the USB flash drive
(p. 28).
[F3] (INFO)
Displays information about the song (p. 29).
(*) This function is not available for songs that contain a drum
track.
4. Press the [EXIT] button several times to return to
the SONG screen.
28
2. Select a folder.
Button
Description
Cursor buttons
( / )/
Select a folder.
Value dial
[F1] (BACK)
Show the higher-level folder.
[F2] (OPEN)
Show the lower-level folder.
3. Press the [F3] (OK) button to confirm your choice
of folder.
MEMO
The files and folders in the folder you selected will
play back.
Performing Along with a Song
Repeatedly Playing a Specified
Region (A-B Repeat)
4. At the location where you want to stop
repeating, press the [F3] (SET B) button.
The “B” character will light, and the song will continue
repeating between “A” and “B.”
You can use the “A-B Repeat” function to repeatedly play
back a specified region.
A
B
Repeat
If you want to respecify the region, press the [F3] (RESET)
button.
NOTE
This setting cannot be made if the repeat region is
too short.
1. Select a song and play it back.
2. In the SONG MENU screen, press the [F3] (A-B)
button.
The A-B REPEAT screen will appear, and the character “A”
will blink.
If you press the [F1] (CANCEL) button, conventional
playback will resume and the A-B REPEAT screen will
close.
Viewing Song Information
1. In the SONG MENU screen, press the [F3] (INFO)
button.
The SONG INFORMATION screen will appear.
Song name
Rewind
Fast-forward
MEMO
You can use the [F1] ( )/[F2] (
forward/rewind the song.
) buttons to fast-
3. At the location where you want to start
repeating, press the [F3] (SET A) button.
The “A” character will light, and the “B” character will
blink.
Display
Description
Length
Song playback duration
Size
File size
Volume
Song volume (p. 28)
Loop
Song playback type (p. 28)
2. Press the [F3] (OK) button to close the screen.
29
Performing Along with a Song
Play Along with a Song and Record
Your Performance (QUICK REC)
Here’s how you can play the drums along with a song
and record your performance.
* You must first select the drum kit and song that you
want to use for practicing (performing).
* The sound from the MIX IN jack will not be recorded.
1. In the SONG screen, select a song.
2. Press the [ ] (QUICK REC) button.
The QUICK REC screen will appear, and the TD will be in
record-standby mode.
Where the recorded data is exported
When a USB flash drive is connected,
your recorded data is automatically
exported to the USB flash drive. Only the
five most recent recorded performances
will be exported as SMF data (p. 14).
The recorded data is saved in the following folder
of the USB flash drive.
Roland
TD-15 or TD-11
Backup
Kit
QUICK REC
3. Press the [
] button to begin recording.
* When recording begins, the previous recording will
be completely erased.
4. Play the drums along with the song.
5. Press the [ ] button to stop recording.
6. Once again press the [ ] button.
The recorded performance will play back.
7. Press the [
30
] button to stop playback.
SONG_01.MID
SONG_02.MID
SONG_03.MID
SONG_04.MID
SONG_05.MID
Practicing in Coach Mode
The TD’s Coach mode is a unique set of exercises
specifically designed to help build speed, accuracy and
stamina, as well as develop better timing skills.
Throughout the Coach modes, you will discover that
some of them have programmable parameters, allowing
you to adapt the functions to your specific needs.
Selecting a Practice Menu
1. Press the [COACH] button so it’s lit.
The COACH MENU screen will appear.
Correctly Playing in Time with the Beat
(TIME CHECK)
This mode lets you practice playing accurately along
with the metronome.
Start practicing
In the COACH MENU screen, press the [F1] (TIME CHECK)
button; practice will start immediately.
1. Strike the pad in time with the metronome.
The percentage of your strikes that were played with
accurate timing is displayed as a “%” value.
2. Select a menu item, and start practicing.
When you press a button, the corresponding practice
menu item will start immediately.
Button
Menu item
Description
[F1]
TIME CHECK (p. 31)
Strengthens your ability to
play accurate rhythms.
[F2]
QUIET COUNT (p. 32)
Strengthens your ability to
maintain the tempo internally.
WARM UPS (p. 32)
When you want to get
warmed up before you begin
practicing.
[F3]
The screen will indicate whether your pad strikes match
the beat sounded by the metronome.
Scoring
If Score (p. 31) is “ON,” the Time Check will automatically
end when you’ve finished practicing the specified
number of measures. Then your performance will be
scored, and the results will appear in the screen.
Operations common to Coach mode
Basic operations (e.g., changing the tempo, and starting/
stopping) are the same in each of the three Coach mode
items.
Operation
Button/Dial
Change the
tempo
Value dial
Start
[F3] (START)/[
Stop
[F1] (STOP)/[
Make settings
[F2] (SETUP)
Settings
In the TIME CHECK screen, press the [F2] (SETUP) button
to access the settings screen.
]
Parameter
Description
Specifies whether the score will be shown in the
screen.
]
Exit Coach mode [COACH]
Value
Score
OFF
Your performance will not be scored.
Only the timing will be checked.
The score will be shown in the screen.
You can also specify the number of
(4, 8, 16, 32 measures you’ll practice before being
meas)
scored.
ON
When using Warm Ups, you can pause by pressing the [F3]
(PAUSE) button.
Specifies the strictness of scoring.
Grade
EASY
Normal
HARD
Timing will be checked more strictly.
31
Practicing in Coach Mode
Parameter
Value
Display 1
In the screen, select the pad for which a timing graph
will be shown.
Display 2
Gauge
Description
LEFT
BEHIND
The left side of the timing graph is
shown as BEHIND (late).
LEFT
AHEAD
The left side of the timing graph is
shown as AHEAD (early).
Settings
In the QUIET COUNT screen, press the [F2] (SETUP)
button to access the settings screen.
Parameter
Value
Description
Measures
2, 4, 8, 16
(Measures)
Specify the length (measures) of the
interval for which the metronome will
alternate between “Sounding” and
“Quiet.”
* You can press the [F2] (METRO) button to make
metronome settings (p. 13).
Developing Internal Timing Sense
(QUIET COUNT)
Of the measures specified by “Measures,” this setting
specifies the length of the measures that will be “Quiet.”
RANDOM
Quiet
1, 2, 4
This mode will help you develop a good sense of time/
tempo.
For the first few measures, the metronome will sound at
the specified volume; over the next few measures, the
volume will diminish until it is nearly inaudible. This cycle
of several measures will continue until you stop it.
Start practicing
In the COACH MENU screen, press the [F2] (QUIET
COUNT) button; practice will start immediately.
1. Strike the pads in time with the metronome.
• The metronome will sound during the first few
measures. When you reach the last measure during
which the metronome will sound, the screen will
indicate “Ready.”
• When the metronome stops sounding, the screen
indication will change to “Quiet.” Continue striking
the pads during this time.
The length of the Quiet interval will
randomly change each time.
Specifies the length (number of
measures) of the Quiet interval.
* This setting cannot be longer than half
of the Measures value.
* You can press the [F2] (METRO) button to make
metronome settings (p. 13).
WARM UPS
In this mode you’ll successively practice steps 1–3, be
graded on your performance at each step, and then
receive a final evaluation.
You can choose one of three courses, ranging from easy
to difficult. You can also adjust the tempo according to
your level of skill.
MEMO
After you’ve started WARM UPS, you can press the
[F3] (PAUSE) button to pause the WARM UPS.
To resume practicing, press the [F3] (START) button
once again.
If you’re finished with WARM UPS, press the [F1]
(STOP) button.
• After the Quiet region, the proportion of your strikes
that were played at an accurate tempo are shown as
a “%” value.
32
Practicing in Coach Mode
Step 1: Change-Up
In this step, the rhythm type will change every two
measures.
Overall evaluation
This grades your performance at each step, and displays
the overall evaluation.
Starting from half notes, the note values will gradually
become shorter, and will then return to half notes; this
change in rhythms will be repeated.
Evaluation
(display)
Step 2: Auto Up/Down
The tempo will gradually be raised and lowered.
The tempo will increase by 1 BPM (beat-per-minute) for
each beat until the metronome reaches the upper limit;
then the tempo will continue slowing down by 1 BPM
until it reaches the initial tempo.
* Auto Up/Down will be executed if Duration(p. 33) is 10
MINS or 15 MINS.
EXCELLENT!, VERY GOOD!, GOOD, AVERAGE, START OVER
Settings
In the WARM UPS screen, press the [F2] (SETUP) button to
access the settings screen.
Parameter
Value
Description
Specifies the time.
Time required: 5 minutes
5 MINS
Change-Up: 2 minutes
Time Check: 3 minutes
Time required: 10 minutes
Duration
10 MINS
Change-Up: 3 minutes
Auto Up/Down: 3 minutes
Time Check: 4 minutes
Time required: 15 minutes
* The current tempo value will be the lower tempo
limit.
15 MINS
MEMO
Step 1: Selects the pattern by which the rhythm will vary
during Change-up.
While practicing, you can press the [F1] (SET MAX)
button to specify the current tempo as the upper
limit; if you press the [F1] (CLR MAX) button, the
upper tempo limit will return to 260.
Step 3:Time Check
Change-Up: 5 minutes
Auto Up/Down:5 minutes
Time Check: 5 minutes
ChangeUp
At this step, the accuracy of your playing will be checked
against the metronome. You can see in the screen if you
are ahead, behind or on the beat.
Max
Tempo
Step 2: Specifies the upper tempo limit during step 2: Auto
Up/Down.
* You can press the [F2] (METRO) button to make
metronome settings (p. 13).
33
Settings for the Entire TD (SYSTEM)
Parameters that apply to the entire TD, such as the metronome settings and the pad sensitivity, are called “system parameters.”
Here we’ll explain the procedure for setting the system parameters, and what each parameter does.
Basic procedure
1. In the DRUM KIT screen (p. 11), press the [MENU] button.
The KIT MENU screen will appear.
2. Press the (
) cursor button to scroll the screen until the SYSTEM icon appears.
3. Press the [F3] (SYSTEM) button.
The SYSTEM screen will appear.
4. Use the cursor buttons (
/ ) to select the desired menu of settings.
The following menus are available.
Menu
Description
Page
Options
Settings for display contrast and power
(Auto Off )
p. 35
Metronome
Metronome settings
p. 36
Pad Control
Settings for the pads connected to the
TRIGGER IN AUX jack
p. 36
MIDI
MIDI-related settings
p. 37
USB Memory
Using a USB flash drive
p. 38
Pad Settings
Pad settings
p. 41
Information
View information about the TD itself
p. 46
Factory Reset
Reset the TD to its factory settings
p. 46
5. Press the [F3] (ENTER) button.
Make the appropriate settings for each menu.
6. Use the cursor buttons (
parameter.
/ ) to select a parameter, and use the value dial to change the value of the
7. Press the [EXIT] button several times to return to the DRUM KIT screen.
34
Settings for the Entire TD (SYSTEM)
Overall Settings for the TD (Options)
For details on the procedure, refer to “Basic procedure” (p. 34).
Parameter
Value
Description
Adjusts the contrast of the display.
Display Contrast
1–10
MEMO
In the DRUM KIT screen, you can adjust this by holding down the [MENU] button and
turning the value dial.
Display Brightness
1–10
Adjusts the brightness of the display.
You can make the ring of the value dial light up in synchronization with your performance.
Illumination Ring
OFF
The ring will not light.
DYNAMIC
The ring will light according to the dynamics of your playing.
KICK
The ring will light when you play the kick drum.
TEMPO
The ring will light in synchronization with the tempo setting.
You can make the [DRUM KIT] buttons light up.
Illumination Kit Buttons
OFF
The [DRUM KIT] buttons will not light.
ON
The [DRUM KIT] buttons will light.
When shipped from the factory, the TD is set to automatically power-off when 30 minutes have elapsed since
it was last played or operated. Approximately five minutes before the power turns off, a message will appear
in the display.
10 MINS
The power will turn off automatically when 10 minutes have elapsed.
30 MINS
The power will turn off automatically when 30 minutes have elapsed.
4 HOURS
The power will turn off automatically when four hours have elapsed.
OFF
The power will not turn off automatically.
USB Audio Volume
0–100
Adjusts the volume when using the TD to listen to audio data played back from your
computer.
Write Protect
OFF, ON
If the Write Protect setting is ON, it will not be possible to save any settings.
Auto Off
35
Settings for the Entire TD (SYSTEM)
Metronome Setup
(Metronome)
Using a Pad as a Switch
(Pad Control)
1. In step 4 of the basic procedure (p. 34), choose
“Metronome” and press the [F3] (ENTER) button
to access the METRONOME SETUP screen.
A pad connected to the TRIGGER IN AUX jack can
function as a switch to change drum kits or to start/stop
a song.
* This setting is valid only in the DRUM KIT screen and
the SONG screen.
NOTE
You must select the correct pad type (p. 41) for the pad
that’s connected.
1. In step 4 of the basic procedure (p. 34), choose
2. From the following list, select the item that you
want to set.
“Pad Control” and press the [F3] (ENTER) button
to access the PAD CONTROL screen.
2. Use the cursor buttons (
/ ) to move the cursor
to “AUX Head” or “AUX Rim.”
Button
Description
[F1] (TIMSIG)
Set the time signature of the metronome.
[F2] (SOUND)
Set the volume of the metronome.
[F3] (MIDI)
Use incoming MIDI messages from
your DAW software etc. to sound the
metronome.
AUX Head
3. Use the cursor buttons (
/ ) to select a
parameter, and use the value dial to edit the
setting.
Parameter
Value
Description
Beat
1–9
Metronome time
signature
Rhythm Type
Half notes, quarter
notes, eighth
notes, eighth note
Metronome interval
triplets, sixteenth
notes (shown as a
note symbol)
TIMSIG
SOUND
Sound
15 types
Metronome tone
Volume
0–10
Metronome volume
Pan
L15–R15
Metronome panning
Output
OUTPUT+
PHONES, PHONES ONLY
Metronome output
destination
MIDI Channel
OFF, 1–16
MIDI channel that will
sound the metronome
Note# Accent
0 (C-1)–127 (G9)
Note number for the
first beat
Note# Normal
0 (C-1)–127 (G9)
Note number for
subsequent beats
MIDI
36
AUX Rim
3. Use the value dial to select the function that you
want to control.
Function
Description
OFF
Disables the pad control function.
KIT+
Selects the next kit.
KIT-
Selects the previous kit.
SONG PLAY
Starts song playback.
SONG STOP
Stops song playback.
SONG PLAY/
STOP
Starts/stops song playback each time you
strike the pad.
TAP TEMPO
Set the tempo according to the interval at
which you strike the pad.
Settings for the Entire TD (SYSTEM)
MIDI-Related Settings (MIDI)
Here you can set MIDI settings for the entire TD.
There are many possibilities when using MIDI, such as:
Use the pads to play external MIDI instruments
You can layer sounds on the TD as well as play sounds from MIDI sound modules and
samplers.
Use the TD as a sound module
Using the DAW software, you can use the TD as a dedicated drum sound module.
For details on the procedure, refer to “Basic procedure” (p. 34).
Parameter
Value
Description
Std MIDI Setup Lock
OFF, ON
Turn this ON if you’re using V-Drums Friend Jam or V-Drums Tutor (sold separately) (p. 47).
MIDI Channel
OFF, 1–16
Specifies the transmit/receive channel
Specifies whether the TD’s pads will be
connected to the internal sound generator
(ON) or disconnected from the internal
sound generator (OFF).
Normally you will leave this “ON.” However,
you should choose the “OFF” setting when
you’re using the TD’s pads only to control an
external sound module, or when using the
TD in conjunction with DAW software on
your computer.
Local Control
DAW software on your computer
Recording
MIDI Thru: ON
TD
Internal
Sound
Generator
OFF, ON
Using Local Control
When using the TD in conjunction with your
DAW software, the notes you play by striking
the pads might be sounded in duplicate
together with the notes that are “echoedback” by your DAW software.
Local Control: OFF
Pad
If this occurs, set Local Control to the “OFF” setting so that the TD’s pads will be disconnected
from the internal sound generator, allowing you to use the TD in conjunction with the DAW
software on your computer as shown in the illustration.
Note Chase
OFF, ON
Prog Change Tx
OFF, ON
If this function is “ON,” incoming MIDI data that matches a pad’s assignment will cause the
screen to show the edit screen of the instrument used by that pad, or cause the cursor to
move.
Specifies whether program change messages will be transmitted (ON) or not transmitted
(OFF).
If this is “ON,” a program number will be transmitted when you switch drum kits on the TD.
Prog Change Rx
OFF, ON
Specifies whether program change messages arriving from DAW software on your computer
will be received (ON) or ignored (OFF).
If this is “ON,” incoming program changes will select the drum kit of the corresponding
number.
37
Settings for the Entire TD (SYSTEM)
1. Proceed up through step 4 on p. 38.
2. Use the value dial to select the save-destination
Using USB Flash Drive
(USB Memory)
number.
1. First connect your USB flash drive to the TD (p. 9).
2. In step 4 of the basic procedure (p. 34), choose
“USB Memory” and then press the [F3] (ENTER)
button to access the USB MEMORY screen.
3. Use the cursor buttons (
desired menu item.
/ ) to select the
Description
Page
Save Backup
Save data to the USB flash drive.
p. 38
Load Backup
Load data from the USB flash
drive into the TD.
p. 39
Delete Data
Delete data from the USB flash
drive.
p. 39
Information
View information about the USB
flash drive.
p. 40
Format
Format the USB flash drive.
p. 40
4. Press the [F3] (ENTER) button.
Make settings as appropriate for the selected menu item.
Saving Data to a USB Flash Drive
(Save Backup)
• All drum kits
3. Press the [F2] (NAME) button.
The SAVE screen will appear.
You can assign a name of up to eight characters.
) or [F2] ( ) button to move the
cursor to the character that you want to change.
Menu
Data that will be saved
If you don’t need to assign a name, proceed to step 10.
4. Press the [F1] (
You can choose from the following menu items.
Here’s how to save TD data to a USB flash drive.
Next you can assign a name to the data that will be
saved.
5. Use the value dial to change the character.
Here you can hold down the [F3] (DEL/INS) button and
use the [F1][F2]buttons to delete or insert a character.
Button
Description
[F3] +
[F1] (DELETE)
Deletes the character at the cursor
location, and moves the subsequent
characters one place to the left.
[F3] +
[F2] (INSERT)
Inserts a space at the cursor location
and moves the subsequent characters
one place to the right.
6. When you’ve assigned a name, press the [EXIT]
button to return to the previous screen.
7. Press the [F3] (SAVE) button.
* If you select a number in which data has already
been saved, and then press the [F3] (SAVE) button,
a confirmation message will appear, asking you
whether you really want to overwrite the data.
If you decide to cancel, press the [F1] (CANCEL)
button and then reselect the save-destination
number.
If it is OK to overwrite the existing data, press the [F3]
(OK) button.
• System settings
When the data has been saved, the screen will indicate
“Completed.”
38
Settings for the Entire TD (SYSTEM)
Loading Data from a USB Flash Drive
Back into the TD (Load Backup)
Data you’ve saved on a USB flash drive can be loaded
back into the TD.
Deleting Data from a USB Flash
Drive (Delete Data)
Here’s how to delete data that’s been saved on a USB
flash drive.
NOTE
• All data and settings in the TD will be overwritten.
• You can’t load data if “Write Protect” (p. 35) is turned
ON.
1. Proceed up through step 4 on p. 38.
2. Use the cursor buttons ( / ) to choose “Data
1. Proceed up through step 4 on p. 38.
2. Use the value dial to select the data that you
want to load.
3. Press the [F3] (LOAD) button.
A confirmation message will appear.
Type,” and then use the value dial to choose the
type of data that you want to delete.
Data type
Description
1 KIT
A drum kit saved by “1 KIT SAVE” (p. 24)
BACKUP
Backup data
3. Use the cursor buttons (
/ ) to choose “File,”
and then use the value dial to select the number
of the data that you want to delete.
4. Press the [F3] (DELETE) button.
A confirmation message will appear.
If you decide to cancel, press the [F1] (CANCEL) button.
4. To load the data, press the [F3] (OK) button.
When the data has been loaded, the screen will indicate
“Completed.”
If you decide to cancel, press the [F1] (CANCEL) button.
5. To delete the data, press the [F3] (OK) button.
When the backup data has been deleted, the screen will
indicate “Completed.”
39
Settings for the Entire TD (SYSTEM)
Viewing Information About the
USB Flash Drive (Information)
Here’s how to view information about the USB flash drive.
Formatting a USB Flash Drive
(Format)
NOTE
When you execute the Format operation, all data on
the USB flash drive will be erased.
Parameter
Description
Backups
Number of data backups
Kits
Number of saved drum kits
Size Used
Amount of memory used on the USB
flash drive
1. Proceed up through step 4 on p. 38.
2. Press the [F3] (FORMAT) button.
A confirmation message will appear.
1. Proceed up through step 4 on p. 38.
2. When you’ve viewed the information, press the
[F3] (OK) button to close the screen.
If you decide to cancel, press the [F1] (CANCEL) button.
3. If you’re sure that you want to format the USB
flash drive, press the [F3] (OK) button.
Once again, a confirmation message will appear.
If you decide to cancel, press the [F1] (CANCEL) button.
4. If you’re sure that you want to format the USB
flash drive, press the [F3] (OK) button.
When formatting has been completed, the screen will
indicate “Completed.”
40
Settings for the Entire TD (SYSTEM)
Optimizing the Pad Settings (Pad Settings)
1. In step 4 of the basic procedure (p. 34), choose “Pad Settings” and then press the [F3] (ENTER) button to access
the PAD SETTINGS screen.
2. Choose one of the following items to edit.
Button
Description
Page
[F1] (TYPE)
Specify the type of pad
p. 41
[F2] (BASIC)
Adjust the pad sensitivity
p. 42
[F3] (ADVNCD)
Make advanced settings for the trigger parameters
p. 43
3. Strike a pad to select the pad for which to make settings.
4. Use the cursor buttons ( / ) to select a parameter, and use the value dial to edit the value.
Specifying the Type of Pad [F1] (TYPE)
You can select the type of pad you’re using (Pad Type) so the TD will accurately receive the signal from the pad.
Parameter
Pad Type
Value
Description
KD-7, KD-8, KD-9, KD-120, KD-140, PD-8, PD-85, PD-105, PD-108, PD-125, PD-128, PDX-6, PDX-8,
PDX100, CY-5, CY-8, CY-12C, CY-13R, CY-14C, CY-15R, VH-11, RT-10K, RT-10S, RT-10T
The pad type is a collection of parameters optimized for
specific models of pad.
If you select the appropriate trigger type for each pad you’ve
connected, all parameters (except for Crosstalk Cancel) will be
set to the optimal values.
However, these are only the typical values, so you may need to
make fine adjustments according to how you’ve attached the
pads or the way in which you’re using them.
The following pads should be connected to the “SNR,” “T1–3,” or “AUX” trigger input.
If these pads are connected to any other trigger input, the signal of a rim strike will not be detected correctly.
Pads
PD-85, PD-105, PD-108, PD-125, PD-128, PDX-6, PDX-8, PDX-100, RT-10S
41
Settings for the Entire TD (SYSTEM)
Setting the Pad Sensitivity [F2] (BASIC)
When you specify the pad type (p. 41), the following settings (basic trigger
parameters) are automatically set to the values appropriate for each pad, meaning
that you will normally not need to adjust them. If you wish to make detailed
adjustments, you can edit the following parameters for each pad.
MEMO
The velocity monitor at the left of the screen indicates the velocity.
Parameter
Value
Pad Type
Refer to p. 41.
Description
You can adjust the sensitivity of the pads to accommodate your personal playing style.
Sensitivity
1–32
This allows you to have more dynamic control over the sound volume, based on how hard you play.
Higher sensitivity allows the pad to produce a loud volume even when played softly.
Lower sensitivity will keep the pad producing a low volume even when played forcefully.
This setting allows a trigger signal to be received only when
the pad is above a determined dynamic level (velocity). This
can be used to prevent a pad from sounding because of
vibrations from other pads.
Threshold
0–31
Threshold
A
B
C
In the example at the right, B will sound but A and C will
not sound.
When set to a higher value, no sound is produced when the
pad is struck lightly.
Gradually raise the “Threshold” value while striking the pad.
Check this and adjust accordingly. Repeat this process until you get the perfect setting for your playing style.
This setting allows you to control the relation between playing velocity (striking force) and changes in volume. Adjust this
curve until the response feels as natural as possible.
Volume
LINEAR
The standard setting. This produces the most natural correspondence between playing dynamics and volume change.
Playing
Dynamics
Volume
EXP1, EXP2
Volume
Compared to LINEAR, strong dynamics produce a greater change.
Playing
Dynamics
Volume
Playing
Dynamics
Volume
Curve
LOG1, LOG2
Compared to LINEAR, a soft playing produces a greater change.
Playing
Dynamics
Playing
Dynamics
Volume
SPLINE
Extreme changes are made in response to playing dynamics.
Playing
Dynamics
Volume
LOUD1,
LOUD2
Volume
Very little dynamic response, making it easy to maintain strong
volume levels. If you’re using a drum trigger as an external pad,
these settings will produce reliable triggering.
Playing
Dynamics
42
Playing
Dynamics
Settings for the Entire TD (SYSTEM)
Advanced Settings for the Trigger Parameters [F3] (ADVNCD)
When you specify the Pad Type (p. 41), the settings in this screen (advanced trigger parameters) will automatically be set to
the values that are most suitable for that type of pad; this means that with the exception of crosstalk cancellation, you will
normally not need to edit these settings.
You should make fine adjustments to these parameters for each pad only if you experience the problems described in the
explanation of each parameter.
1. Press one of the [F1]–[F3] buttons to select the item that you want to edit.
2. Strike a pad to specify the pad whose settings you want to edit.
3. Use the cursor buttons ( / ) to select a parameter.
4. Use the value dial to edit the value.
[F1] (SCAN)
Parameter
Value
Pad Type
Refer to p. 41.
Description
Specifies the detection time for the trigger signal.
Scan Time
0–4.0 (ms)
Since the rise time of the trigger signal waveform may differ slightly depending on the characteristics of each pad or acoustic drum trigger (drum pickup),
you may notice that identical hits (velocity) may produce sound at different
volumes. If this occurs, you can adjust the “Scan Time” so that your way of
playing can be detected more precisely.
Scan Time
Time
While repeatedly hitting the pad at a constant force, gradually raise the Scan
Time value from “0,” until the resulting volume stabilizes at the loudest level.
At this setting, try both soft and loud hits, and make sure that the volume
changes appropriately.
* As the value is set higher, the time it takes for the sound to be played increases. Set this to the lowest value
possible.
This setting prevents spurious re-triggering.
Important if you are using acoustic drum triggers. Such triggers can
produce altered waveforms, which may also cause inadvertent sounding
at Point A in the figure (Re-trigger).
A
Time
This occurs in particular at the decaying edge of the waveform. Retrig
Cancel detects such distortion in and prevents re-triggering from
occurring.
Retrig Cancel
1–16
While repeatedly striking the pad, raise the “Retrig Cancel” value until
re-triggering no longer occurs.
* Although setting this to a high value prevents re-triggering, it then becomes easy for sounds to be omitted
when the drums played fast (roll etc.). Set this to the lowest value possible while still ensuring that there is
no re-triggering.
MEMO
You can also eliminate this problem of re-triggering with the Mask Time setting (p. 44). Mask Time does not
detect trigger signals if they occur within the specified amount of time after the previous trigger signal
was received. Retrig Cancel detects the attenuation of the trigger signal level, and triggers the sound after
internally determining which trigger signals were actually generated when the head was struck, while
weeding out the other false trigger signals that need not trigger a sound.
43
Settings for the Entire TD (SYSTEM)
Parameter
Value
Description
This setting prevents double triggering.
Mask Time
0–64 (ms)
When playing a kick trigger, the beater can bounce back and
hit the head a second time immediately after the intended
note—with acoustic drums sometimes the beater stays against
the head—is causes a single hit to “double trigger” (two sounds
instead of one). The Mask Time setting helps to prevent this. Once
a pad has been hit, any additional trigger signals occurring within
the specified “Mask Time” (0–64 msec) will be ignored.
Mask Time
Time
Sound not produced
Adjust the “Mask Time” value while playing the pad.
When using a kick trigger, try to let the beater bounce back and hit the head very quickly, then raise the
“Mask Time” value until there are no more sounds made by the beater rebound.
* When set to a high value, it will be difficult to play very quickly. Set this to as low a value as you can.
MEMO
If two or more sounds are being produced when you hit the head just once, then adjust Retrig Cancel (p. 43).
This setting cancels “crosstalk,” which means that when you play one pad you hear a sound coming from
another pad. This can happen when two pads are installed on the same stand.
In some cases you can prevent crosstalk by increasing the distance between the two mounted pads.
Xtalk Cancel
0–80
Crosstalk Example: If you hit the snare pad and the tom 1 also sounds
While striking the Snare pad, gradually increase the “Xtalk Cancel” value for the tom 1 pad until the tom 1
pad no longer sounds when you hit the Snare pad. If you raise the “Xtalk Cancel” higher, the tom 1 pad will
be less prone to receive crosstalk from other pads.
* If the value is set too high, and two pads are played simultaneously, the one that is struck less forcefully
may not sound. Be careful and set this parameter to the minimum value required to prevent crosstalk.
[F2] (RIM)
Parameter
Value
Trig Type
Refer to p. 41.
Rim Gain
0–8.0
Description
When a PD-8/PD-85/PD-105/PD-108/PD-125/PD-128, PDX-6/PDX-8/PDX-100, CY series pad, VH-11, or RT-10S
is connected, you can adjust the relation between your playing velocity (force) on the rim/edge and the
resulting volume level.
Higher value allows the rim/edge to produce a loud volume even when played softly. Lower value will keep
the rim/edge producing a low volume even when played forcefully.
When a PD-85/PD-105/PD-108/PD-125/PD-128, PDX-6/PDX-8/PDX-100, or RT-10S is connected, you can
adjust the sensitivity of the head response.
Head/Rim Adj
0–80
Xstick Adj
-9–+9
There are some cases that you have a rim sound unexpectedly when you hit the head strongly. You can
improve this situation with decreasing the value of “Head/Rim Adj.” When you set the value too big, it might
be difficult to play the rim sound.
Specifies the striking force at which to switch between the cross-stick sound and the open rim shot sound.
With positive (+) settings, the cross stick sound will be heard even for strong strikes.
[F3] (HIHAT)
44
Parameter
Value
Pedal HH Sens
-5–+5
Description
Adjusts the sensitivity for playing foot-close or foot-splash notes.
Positive (“+”) settings allow louder sounds to be produced even when you step lightly on the pedal.
Settings for the Entire TD (SYSTEM)
Connecting the VH-11 and making
settings on the TD
8. Press the [F3] (ADVNCD) button, and then press
the [F3] (HIHAT) button.
The following screen will appear.
Connections
Clutch screw
Motion sensor unit
9. While you watch the meter that’s displayed in
the left side of the screen, turn the VH-11’s VH
offset adjustment screw to adjust it.
Adjust the screw so that the black
meter.
TRIGGER OUT
jack
appears in the
VH Offset Adjustment Screw
CONTROL OUT jack
OPEN
Connect the HH cable
CLOSE
Connect the HHC cable
Settings
1. Make sure that the VH-11 is correctly connected
to the TD.
2. Set up the hi-hat, take your foot off the pedal,
and power-on the TD.
* It will be impossible to make the adjustment correctly
if the hi-hat is touching the motion sensor when you
turn on the power.
VH Offset Adjustment Points
If the closed hi-hat sound is difficult to attain,
rotate the VH offset adjustment screw towards
“CLOSE.”
If the open hi-hat sound is difficult to attain,
rotate the screw towards “OPEN.”
NOTE
If the sound cuts off when you strike the hi-hat
forcefully, rotate the VH Offset adjustment
screw towards “OPEN.”
3. Loosen the clutch screw, and allow the hi-hat to
rest naturally on top of the motion sensor unit.
4. Proceed up through step 5 of the basic
procedure (p. 34) to access the PAD SETTINGS
screen.
5. Press the [F1] (TYPE) button.
6. Use the cursor buttons ( / ) to select “HH.”
7. Use the value dial to select “VH-11.”
10.Adjust other parameters as needed.
NOTE
If you don’t set up the VH-11 correctly, it may not
operate correctly.
45
Settings for the Entire TD (SYSTEM)
Viewing Information About
the TD (Information)
3. Press the [F3] (RESET) button.
A confirmation message will appear.
Here you can view information about the TD itself.
For details on the procedure, refer to “Basic procedure”
(p. 34).
Item
Description
Program Ver.
System program version
If you decide to cancel, press the [F1] (CANCEL) button.
4. If you’re sure you want to execute the factory
Restoring the Factory Settings
(Factory Reset)
reset, press the [F3] (OK) button.
Once again, a confirmation message will appear.
This “factory reset” operation restores all drum kits and
system settings in the TD to their factory-set state.
NOTE
• All data and settings in the TD will be lost. If the TD
contains any data or settings that you want to keep,
you must save them to a USB flash drive before you
proceed (p. 38).
• This operation cannot be executed if “Write Protect”
(p. 35) is ON.
1. In step 4 of the basic procedure (p. 34), choose
“Factory Reset” and then press the [F3] (ENTER)
button to access the FACTORY RESET screen.
2. Use the value dial to select the type of data that
you want to reset.
Parameter
Target
46
Value
Description
ALL KITS
All kits
SYSTEM
System settings
ALL
All data
If you decide to cancel, press the [F1] (CANCEL) button.
5. If you’re sure you want to execute the factory
reset, press the [F3] (OK) button.
When the factory reset has been completed, the screen
will indicate “Completed.”
Connecting to Your Computer via USB
If you use a commercially available USB cable to connect the TD’s COMPUTER port to a USB port of your computer, sound
played back by your computer can be heard through the TD, and sounds played by the TD can be recorded on your computer.
You’ll also be able to use software such as V-Drums Friend Jam and V-Drums Tutor to enjoyably practice your drumming.
What is V-Drums Friend Jam?
V-Drums Friend Jam is a drummer’s social networking tool that lets you use the V-Drums and your
computer to enjoy practicing/competing with friends around the world. Practice songs can be
automatically downloaded from the internet, and are also linked with Twitter.
Access http://vdru.ms/fj and download it!
What is V-Drums Tutor?
The V-Drums Tutor (sold separately) is a drumming practice software designed to be used with Roland V-Drums, making
your practice time simple, enjoyable, challenging and effective.
Installing the USB Driver
Before connecting the TD to your computer, you must
first install the USB driver.
1. Install the USB driver in your computer.
The dedicated driver for the TD-15 and TD-11 is included
in the attached CD-ROM, or you can download it from
the Roland website.
Connecting the TD to the
Computer
1. Use a commercially available USB cable to
connect the COMPUTER port located on the TD’s
top panel with your computer’s USB port.
Roland website
http://www.roland.com/
For the operating requirements, refer to the Roland
website. The driver program and installation procedure
will differ depending on your system. Please carefully
read the Readme.htm included with the files you
downloaded.
USB cable
* Use a USB cable that supports USB 2.0 Hi-Speed.
47
Troubleshooting
If you don’t hear sound, or if the system does not operate as you expect, please check the following points first.
If you are still unable to resolve the problem, contact your retailer, the nearest Roland Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
Problem
Items to check
Action
Is the connection cable correctly connected to the TRIGGER INPUT connector?
Are the cables correctly connected to each
pad and pedal?
Are the cables correctly connected to the
TD’s OUTPUT jacks?
—
Check the connections.
p. 8
Are the cables correctly connected to the
input jacks of your amp or audio system?
No sound
Could there be a problem with the
connection cables?
Could the [VOLUME] knob be turned all
the way to the left?
USB flash drive is not recognized
Songs saved on the USB flash drive will
not play back correctly
Page
Try using other cables.
—
Try raising the volume of the TD.
If you’re using the TD-15, check the side
panel [VOLUME] knob as well.
p. 7
Have you made the correct input selection
Check your amp or audio system.
setting on your amp or audio system?
—
Are the volume settings of your amp or
audio system appropriate?
Try raising the volume of your amp or
audio system.
—
Check the type of USB flash drive.
Use a USB flash drive sold by Roland. We
cannot guarantee correct operation if any
other product is used.
—
Check the format of the USB flash drive.
The TD can use USB flash drives that are
formatted in FAT format.
p. 40
Reformat the USB flash drive using the TD.
Can’t save the TD’s data to a USB flash
drive
Is there sufficient free space on the USB
flash drive?
Delete unneeded files from the USB flash
drive, or use a higher-capacity USB flash
drive.
p. 39
Use MP3 files that the TD supports.
p. 26
Can’t play back MP3/WAV files
Does the TD support the sampling
frequency and bit rate of the MP3 file, or
the sampling frequency and bit depth of
the WAV file?
Playback may be unable to keep up if you raise the playback speed or change the pitch
of a high bit-rate MP3.
Can’t correctly set the A-B repeat times
Computer does not recognize the TD
48
It’s not possible to set the “A” and “B” times
any closer than one second.
Make sure that there is at least one second
between the two times.
When using an MP3 file, it might not be possible to play back the A-B repeat region
correctly.
Is the TD correctly connected to your
computer?
Check the connection to your computer.
Is the USB driver installed?
You must first install the USB driver in your
computer.
Make sure that the USB cable connecting
the TD to your computer’s USB port is
compatible with USB 2.0 Hi-Speed.
Use a computer and cable that support
USB 2.0 Hi-Speed.
—
p. 29
p. 47
Error Messages
If an error message is displayed in the TD’s screen, the TD was unable to operate correctly or was operated inappropriately.
Take the appropriate action listed below.
Message
Meaning
Action
Error messages related to MIDI
MIDI buffer full.
A large amount of MIDI messages was received
Reduce the amount of MIDI messages being transmitted
in a short time, and the TD was unable to
to the TD.
process them.
MIDI Tx buffer full.
More data was being transmitted from the
TD than could be sent correctly from the MIDI
OUT connector.
Reduce the amount of data being transmitted.
USB memory full.
The USB flash drive does not have enough
free space.
Either delete unneeded data, or use another USB flash drive.
Check the USB memory.
The USB flash drive is not working correctly.
Check the USB flash drive.
Could not read this file.
The specified data does not exist on the USB
flash drive. Alternatively, the saved data has
been damaged.
Check the USB flash drive.
Unsupported format.
The file format or song format is one that the
TD cannot read.
Check the file. For the supported song formats, refer to p. 26.
USB device error.
Either the connected USB flash drive is one
that the TD cannot use, or a foreign object
has entered the MEMORY port and caused an
electrical short.
Immediately disconnect the connection, and check whether
a foreign object might have entered the MEMORY port.
USB memory busy.
Data could not be read fast enough from the
USB flash drive.
Error messages related to USB
• If this error message appears when playing back high
bit-rate MP3 data, or when you’ve raised the playback
speed of MP3 data, you may be able to solve the problem
by lowering the bit rate or setting the speed to normal.
• Use a USB flash drive sold by Roland.
Error messages related to the TD’s internal memory
Internal memory full.
The QUICK REC storage capacity is full, and
recording has stopped.
—
Error messages related to the system
Device error.
There is a problem with the internal system.
Contact your retailer, the nearest Roland Service Center,
or an authorized Roland distributor, as listed on the
“Information” page.
Data memory was damaged.
There is a problem with internal memory.
A factory reset will be executed automatically.
Other messages (* These are not errors)
If you don’t want the power to turn off, press any button or
strike a pad.
The module will turn off soon.
The power will soon turn off because of the
“Auto Off” setting.
USB memory is not connected
here.
A USB flash drive is not connected to the TD.
Connect a USB flash drive.
This page is invalid when Std
MIDI Setup Lock is on.
If Std MIDI Setup Lock is ON, the settings of
this page are ignored.
To enable these settings, turn Std MIDI Setup Lock off (p. 37).
Write Protect is ON.
The operation cannot be executed because
Write Protect is on.
If you want to execute this operation, turn Write Protect off
(p. 35).
Not possible if recorded drum
data exists.
This function cannot be used on an internal
song that contains a drum track, or on a song
in which you recorded a drum performance
using the QUICK REC function.
When you reselect the song, the drum performance you
recorded using the QUICK REC function will be erased, and
you will once again be able to use this function.
You can also disable the “Auto Off” setting so that the power
does not turn off automatically (p. 35).
49
Main Specifications
Roland TD-15
Roland TD-11: Drum Sound Module
Drum Kits
TD-15
100
TD-11
50
Ambience (10 types)
Effect Types
4-Band Equalizer
Multi Effect (10 types) *TD-15 ONLY
Resolution
480 ticks per quarter note
Recording
Method
Real-time
Maximum Note
Storage
approx. 30,000 Notes
File Format
Audio File
WAV/MP3
Illumination Ring *TD-15 ONLY
Dynamic, Kick, Tempo
Display
64 x 128 dots Graphic Type LCD (backlit LCD)
Quick Rec
TRIGGER INPUT connector (DB-25 type) (Kick, Snare, Tom1, Tom2, Tom3, Hi-Hat, Crash1, Ride, Ride Bell, Hi-Hat Control)
Extra Trigger
Input jacks
Connectors
TD-15
2 (CRASH2,AUX) (Stereo 1/4-inch phone type)
TD-11
1 (CRASH2) ( Stereo 1/4-inch phone type)
OUTPUT jacks (L/MONO, R) (Stereo 1/4-inch phone type)
PHONES jack (Stereo 1/4-inch phone type)
MIX IN jack (stereo miniature phone type)
MIDI OUT connector
USB COMPUTER port
USB MEMORY port
Interface
Hi-Speed USB (USB-MIDI, USB-AUDIO, USB Flash Drive)
Output Impedance
1.0 k ohms
Power Supply
AC adaptor (DC 9 V)
Current Draw
Dimensions
Weight
TD-15
450 mA
TD-11
350 mA
154 (W) x 89 (D) x 225 (H) mm
6-1/16 (W) x 3-9/16 (D) x 8-7/8 (H) inches
TD-15
685 g / 1 lb 9 oz (excluding AC Adaptor)
TD-11
665 g / 1 lb 8 oz (excluding AC Adaptor)
Accessories
Owner’s Manual, AC Adaptor, Special Connection Cable, Wing Bolt (M5 x 10) x 2, Sound Module Mounting Plate,
CD-ROM (Play-along Audio Song/USB Driver)
Options (sold separately)
Pads (PD series, PDX series), Cymbals (CY series), Kick (KD series), Hi-Hat (VH-11), Hi-Hat Control Pedal (FD series), Stand (MDS series), Cymbal Mount (MDY series), Pad Mount (MDH series), Acoustic Drum Trigger (RT series), Personal Drum Monitor: PM-10, PM-30, V-Drums Accessory Package: DAP-3, V-Drums Mat (TDM-20/TDM-10), USB Flash Drive
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without
prior notice.
50
Index
A
L
S
A-B repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
ADVNCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
ambience. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
send. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
audio files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Auto Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
loading
drum kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Load Backup. . . . . . . . . . . . . . . . . . . . . . . . 39
saving
drum kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Save Backup. . . . . . . . . . . . . . . . . . . . . . . . 38
selecting
song. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SEND
ambience. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
snare buzz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
song
information. . . . . . . . . . . . . . . . . . . . . . . . . 29
playing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
selecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SONG screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
strainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SuperNATURAL. . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SWITCH
multi-effect. . . . . . . . . . . . . . . . . . . . . . . . . 21
SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
B
basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Behavior Modeling Technology. . . . . . . . . . . . 5
C
Coach mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
copying
drum kit or pad. . . . . . . . . . . . . . . . . . . . . 23
cross-stick . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 12
M
MENU screens . . . . . . . . . . . . . . . . . . . . . . . . . . 16
metronome. . . . . . . . . . . . . . . . . . . . . . . . . . 13, 36
MIDI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
MIDI note number . . . . . . . . . . . . . . . . . . . . . . 22
muffling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
multi effects. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
N
naming
drum kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
D
O
deleting
Delete Data. . . . . . . . . . . . . . . . . . . . . . . . . 39
Display Brightness. . . . . . . . . . . . . . . . . . . . . . 35
Display Contrast . . . . . . . . . . . . . . . . . . . . . . . . 35
drum kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
copying. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
creating . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
naming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
restoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
saving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DRUM KIT screen. . . . . . . . . . . . . . . . . . . . . . . . 11
Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
E
effects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
EQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
F
Factory Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . 46
folder. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 28, 30
formatting
USB flash drive. . . . . . . . . . . . . . . . . . . . . . 40
FX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FX parameter list. . . . . . . . . . . . . . . . . . . . . . . . 20
H
P
pad
copying. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Pad Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
pad sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . 42
Pad Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
playing
song. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
power on/off. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
previewing
instrument. . . . . . . . . . . . . . . . . . . . . . . . . . 17
Q
QUICK EDIT function. . . . . . . . . . . . . . . . . . . . 15
QUICK REC. . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 30
R
recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
restoring
drum kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
factory settings . . . . . . . . . . . . . . . . . . . . . 46
rim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
T
tempo
metronome. . . . . . . . . . . . . . . . . . . . . . . . . 13
trigger parameters. . . . . . . . . . . . . . . . . . . . . . 43
tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
U
USB driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
USB flash drive. . . . . . . . . . . . . . . . . . . . . . . 24, 26
formatting. . . . . . . . . . . . . . . . . . . . . . . . . . 40
system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
USB Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
V
V-Drums Friend Jam. . . . . . . . . . . . . . . . . . . . . 47
V-Drums Tutor. . . . . . . . . . . . . . . . . . . . . . . . . . 47
volume
drum kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
metronome. . . . . . . . . . . . . . . . . . . . . . . . . 13
link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
I
information
song. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
USB flash drive. . . . . . . . . . . . . . . . . . . . . . 40
INST EDIT parameter list. . . . . . . . . . . . . . . . . 18
instrument. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
changing. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
editing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
previewing . . . . . . . . . . . . . . . . . . . . . . . . . 17
51
MEMO
52
Information
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar Al Askalany Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: (022)-417-1828
REUNION
MARCEL FO-YAM Sarl
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
T.O.M.S. Sound & Music (Pty)Ltd.
2 ASTRON ROAD DENVER
JOHANNESBURG ZA 2195,
SOUTH AFRICA
TEL: (011) 417 3400
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd. (BEIJING OFFICE)
3F, Soluxe Fortune Building
63 West Dawang Road, Chaoyang
District, Beijing, CHINA
TEL: (010) 5960-2565
HONG KONG
Tom Lee Music
11/F Silvercord Tower 1
30 Canton Rd
Tsimshatsui, Kowloon,
HONG KONG
TEL: 852-2737-7688
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 852-2333-1863
INDIA
Rivera Digitec (India) Pvt. Ltd.
411, Nirman Kendra Mahalaxmi
Flats Compound Off. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
TEL: (022) 2493 9051
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
TAIWAN
ECUADOR
ROLAND TAIWAN ENTERPRISE
CO., LTD.
9F-5, No. 112 Chung Shan
North Road Sec. 2 Taipei 104,
TAIWAN R.O.C.
TEL: (02) 2561 3339
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - ECUADOR
TEL: (593-4) 2302364
THAILAND
Theera Music Co. , Ltd.
100-108 Soi Verng Nakornkasem,
New Road,Sumpantawong,
Bangkok 10100, THAILAND
TEL: (02) 224-8821
VIET NAM
VIET THUONG CORPORATION
386 CACH MANG THANG TAM ST.
DIST.3, HO CHI MINH CITY,
VIET NAM
TEL: (08) 9316540
OCEANIA
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099,
AUSTRALIA
For Australia
TEL: (02) 9982 8266
For New Zealand
TEL: (09) 3098 715
CENTRAL/LATIN
AMERICA
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires, ARGENTINA
TEL: (011) 4508-2700
BARBADOS
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, BARBADOS
TEL: (246) 430-1100
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 211
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
INDONESIA
PT. Citra Intirama
Ruko Garden Shopping Arcade
Unit 8 CR, Podomoro City
Jl.Letjend. S.Parman Kav.28
Jakarta Barat 11470, INDONESIA
TEL: (021) 5698-5519/5520
COSTA RICA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
MALAYSIA/
SINGAPORE
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
OMNI MUSIC
75 Avenida Norte y Final Alameda
Juan Pablo II,
Edificio No.4010 San Salvador,
EL SALVADOR
TEL: 262-0788
GUATEMALA
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala,
GUATEMALA
TEL: (502) 599-2888
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, HONDURAS
TEL: (504) 553-2029
MARTINIQUE
Musique & Son
Z.I.Les Mangle
97232 Le Lamentin,
MARTINIQUE F.W.I.
TEL: 596 596 426860
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
MARTINIQUE F.W.I.
TEL: 596 596 715222
MEXICO
COLOMBIA
KOREA
EL SALVADOR
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, COLOMBIA
TEL: (574) 3812529
JUAN Bansbach Instrumentos
Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico D.F.,
MEXICO
TEL: (55) 5668-6699
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, NICARAGUA
TEL: (505) 277-2557
PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE PANAMA
TEL: 315-0101
PARAGUAY
Distribuidora De Instrumentos
Musicales
J.E. Olear y ESQ. Manduvira
Asuncion, PARAGUAY
TEL: (595) 21 492147
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - PERU
TEL: (511) 4461388
TRINIDAD
AMR Ltd
Ground Floor
Maritime Plaza
Barataria TRINIDAD W.I.
TEL: (868) 638 6385
URUGUAY
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL: (305) 5926866
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
DOMINICAN REPUBLIC
VENEZUELA
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
DOMINICAN REPUBLIC
TEL: (809) 683 0305
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar import
#7 zona Industrial de Turumo
Caracas, VENEZUELA
TEL: (212) 244-1122
CURACAO
EUROPE
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
CROATIA
RUSSIA
OMAN
Roland Music LLC
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (495) 981-4967
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
SERBIA
Music AP Ltd.
Sutjeska br. 5 XS - 24413 Palic,
SERBIA
TEL: (024) 539 395
SLOVAKIA
ART-CENTAR
Degenova 3.
HR - 10000 Zagreb, CROATIA
TEL: (1) 466 8493
DAN Acoustic s.r.o.
Povazská 18.
SK - 940 01 Nové Zámky,
SLOVAKIA
TEL: (035) 6424 330
CZECH REP.
SPAIN
CZECH REPUBLIC DISTRIBUTOR
s.r.o
Voctárova 247/16
180 00 Praha 8, CZECH REP.
TEL: (2) 830 20270
DENMARK
Roland Scandinavia A/S
Skagerrakvej 7 Postbox 880
DK-2100 Copenhagen,
DENMARK
TEL: 3916 6200
FINLAND
Roland Scandinavia As, Filial
Finland
Vanha Nurmijarventie 62
01670 Vantaa, FINLAND
TEL: (0) 9 68 24 020
GERMANY/AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
TEL: (040) 52 60090
GREECE/CYPRUS
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
2045. Törökbálint, FSD Park 3. ép.,
HUNGARY
TEL: (23) 511011
IRELAND
Roland Ireland
E2 Calmount Park, Calmount
Avenue, Dublin 12,
Republic of IRELAND
TEL: (01) 4294444
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
NORWAY
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo,
NORWAY
TEL: 2273 0074
POLAND
ROLAND POLSKA SP. Z O.O.
ul. Kty Grodziskie 16B
03-289 Warszawa, POLAND
TEL: (022) 678 9512
PORTUGAL
Roland Systems Group EMEA, S.L.
Branch Office Porto
Edifício Tower Plaza
Rotunda Eng. Edgar Cardoso
23, 9ºG
4400-676 Vila Nova de Gaia,
PORTUGAL
TEL: (+351) 22 608 00 60
ROMANIA
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni, ROMANIA
TEL: (266) 364 609
Roland Systems Group EMEA, S.L.
Paseo García Faria, 33-35
08005 Barcelona, SPAIN
TEL: 93 493 91 00
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Mårbackagatan 31, 4 tr.
SE-123 43 Farsta, SWEDEN
TEL: (0) 8 683 04 30
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen, SWITZERLAND
TEL: (061) 975-9987
UKRAINE
EURHYTHMICS Ltd.
P.O.Box: 37-a.
Nedecey Str. 30
UA - 89600 Mukachevo, UKRAINE
TEL: (03131) 414-40
QATAR
AL-EMADI TRADING &
CONTRACTING CO.
P.O. Box 62, Doha, QATAR
TEL: 4423-554
SAUDI ARABIA
aDawliah Universal Electronics
APL
Behind Pizza Inn
Prince Turkey Street
aDawliah Building,
PO BOX 2154,
Alkhobar 31952,
SAUDI ARABIA
TEL: (03) 8643601
SYRIA
Technical Light & Sound Center
PO Box 13520 Bldg No.49
Khaled Abn Alwalid St.
Damascus, SYRIA
TEL: (011) 223-5384
TURKEY
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.33
Beyoglu, Istanbul, TURKEY
TEL: (0212) 249 85 10
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Ground Floor, Dubai,
U.A.E.
TEL: (04) 3360715
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, SWANSEA SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
NORTH AMERICA
CANADA
MIDDLE EAST
BAHRAIN
Moon Stores
No.1231&1249 Rumaytha
Building Road 3931,
Manama 339, BAHRAIN
TEL: 17 813 942
IRAN
MOCO INC.
Jadeh Makhsous Karaj (K-9),
Nakhe Zarin Ave.
Jalal Street, Reza Alley No.4
Tehran 1389716791, IRAN
TEL: (021)-44545370-5
ISRAEL
Roland Canada Ltd.
(Head Office)
5480 Parkwood Way Richmond B.
C., V6V 2M4, CANADA
TEL: (604) 270 6626
Roland Canada Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6,
CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha'alia Hashnia St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
JORDAN
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192, JORDAN
TEL: (06) 5692696
KUWAIT
EASA HUSAIN AL-YOUSIFI &
SONS CO.
Al-Yousifi Service Center
P.O.Box 126 (Safat) 13002,
KUWAIT
TEL: 00 965 802929
LEBANON
Chahine S.A.L.
George Zeidan St., Chahine Bldg.,
Achrafieh, P.O.Box: 16-5857
Beirut, LEBANON
TEL: (01) 20-1441
As of Feb. 1, 2011 (ROLAND)
53
54
DECLARATION OF CONFORMITY
Compliance Information Statement
For the USA
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
55
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement