Commell FS-A76 User's Manual

Add to my manuals
41 Pages

advertisement

Commell FS-A76 User's Manual | Manualzz

FS-A76

PICMG1.3 Full-size CPU Card

User’s Manual

Edition 1.4

2014/03/13

FS-A76 User’s Manual

Copyright

Copyright 2013, all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products.

This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer.

All trademarks and/or registered trademarks contains in this document are property of their respective owners.

Disclaimer

The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product.

The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose.

The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.

Trademark

All trademarks are the property of their respective holders.

Any questions please visit our website at http://www.commell.com.tw

-1-

FS-A76 User’s Manual

Packing List:

Please check the package content before you starting using the board.

Hardware:

FS-A76 PICMG1.3 Full-size CPU Card motherboard x 1

Cable Kit:

SATA Cable x 2

(OALSATA3-L)/ (1040529)

DVI module with bracket x 1

(BADPDVIP_A&OALDVI-DF13)/

(4120008021&1040483)

PS/2 Keyboard & Mouse Cable x 1

(OALPS2/MKN)/ (1040551)

4-pin to 3-pin ATX cable x 1

(OAL-ATX-C)/ (1040184)

DB25 & DB9 cable x 1

(FS-A76TDG/ FS-A76FTDG Only)

(OAL1S1P)/ (1040041)

Audio Port Cable x 1

(OALPJ-HD)/ (1040120)

USB Cable x 1

(OALUSBA-1)/ (1040172)

Printed Matters:

Driver CD (Including User’s Manual) x 1

DB9 cable x 1 & DB25 cable x 1

(FS-A76TDG2/ FS-A76FTDG2 Only)

(OAL2S1P)/ (1040191)

Optional:

USB3.0 Cable

(OALUSB3)/ (1040531)

-2-

FS-A76 User’s Manual

Index

Chapter 1 <Introduction>

.............................................................6

1.1 <Product Overview>..................................................................................... 6

1.2 <Product Specification>................................................................................ 7

1.3 <Mechanical Drawing>................................................................................. 9

1.4 <Block Diagram>........................................................................................ 10

Chapter 2 <Hardware Setup>

.................................................. 11

2.1 <Connector Location> ................................................................................ 11

2.2 <Jumper Location & Reference>................................................................ 12

2.3 <Connector Reference> ............................................................................. 13

2.3.1 <Internal Connectors> .............................................................. 13

2.3.2 <External Connectors> ............................................................. 13

2.4 <CPU and Memory Setup> ........................................................................ 14

2.4.1 <CPU Setup> ............................................................................. 14

2.4.2 <Memory installation> ............................................................... 15

2.5 <CMOS Setup> .......................................................................................... 15

2.6 <Serial ATA Interface> ................................................................................ 16

2.7 <Ethernet Interface>................................................................................... 17

2.8 <Onboard Display Interface> ..................................................................... 18

2.8.1 <Analog Display> ....................................................................... 18

2.8.2 <DVI Display > ........................................................................... 19

2.9 <Integrated Audio Interface> ...................................................................... 20

2.10 <USB Interface>....................................................................................... 22

2.11 <Serial Port>............................................................................................. 24

2.12 <GPIO and SMBUS Interface>................................................................. 26

2.13 <Power Supply and Fan Interface > ......................................................... 27

2.14 <Switch and Indicator> ............................................................................. 28

Chapter 3 <System Setup>

.......................................................29

3.1 <Audio Configuration>................................................................................ 29

3.2 <Display Properties Setting> ...................................................................... 30

-3-

FS-A76 User’s Manual

Chapter 4 <BIOS Setup>

.............................................................32

Appendix A <I/O Port Pin Assignment>

..........................34

A.1 <Serial ATA Port> .......................................................................................34

A.2 <IrDA Port>.................................................................................................34

A.3 <VGA Port> ................................................................................................34

A.4 <LAN Port>.................................................................................................34

A.5 <LAN LED Port>.........................................................................................35

A.6 <Parallel Port>............................................................................................35

Appendix B <Programming GPIO’s>

.................................36

Appendix C <Programming Watchdog Timer >

.........37

Appendix D <TPM Setup>

..........................................................38

Contact Information

.......................................................................39

-4-

FS-A76 User’s Manual

(This page is left for blank)

-5-

FS-A76 User’s Manual

Chapter 1 <Introduction>

1.1 <Product Overview>

FS-A76 the 3 rd

Generation Intel of the PICMG1.3 Full-size CPU Card motherboard, supports 3 rd

Generation Intel® Core™ i7, Core™ i5, Core™ i3 and Pentium ® Desktop

Processor and features Intel Q77 chipset, integrated HD Graphics, DDR3 memory,

REALTEK High Definition Audio, Serial ATA and Intel Gigabit LAN.

Intel® FCLGA1155 processor

The Intel ® I3/I5/I7/Pentium ® processor now comes with a new form factor with

1155-pin FCLGA package, for 1066/1333MHz front-side-bus, 12MB L2 cache, for 65nm and 45nm manufacturing technology, the PLGA processor without pin header on solder side can make user installing the processor on the socket easier.

Intel ® Q77 PCH chipset

The Intel Q77 integrates DDR3 1066/1333MHz for memory, and HD Graphic technology for new graphic engine. The Q77 integrates with up to 4 USB2.0 interfaces, and serial

ATA II interface with RAID function.

-6-

FS-A76 User’s Manual

1.2 <Product Specification>

General Specification

Form Factor

CPU

PICMG1.3 Full-size CPU Card

3rd Generation Intel® Core™ I3/I5/I7/Pentium ® processor

With LGA1155 socket

Package type: FCLGA 1155

Memory

Chipset

BIOS

2 x 240-pin DDR3 1066/1333MHz SDRAM up to 16GB

Unbufferred, none-ECC memory supported only

Intel® BD82Q77 PCH

Phoenix 64Mb SPI flash BIOS

Green Function Power saving mode includes doze, standby and suspend modes.

ACPI version 3.0 and APM version 1.2 compliant

Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min. of timeout value

Real Time Clock Chipset built-in RTC with lithium battery

Serial ATAII Intel® Q77 PCH integrates 4 Serial ATA II interface& 2 Serial ATA IIl

RAID 0, 1,5,10 Intel Matrix Storage Technology supported

Multi-I/O Port

Chipset

Serial Port

USB Port

IrDA Port

K/B & Mouse

GPIO

Smart Fan

VGA Display Interface

Intel® Q77 PCH with Winbond® W83627DHG-P Controller

Four RS-232 and one RS232/422/485 serial ports

Four Hi-Speed USB 2.0 ports with 480Mbps of transfer rate

Four USB3.0 ports with 5Gbps of transfer rate

One IrDA compliant Infrared interface supports SIR

External PS/2 keyboard and mouse ports on rear I/O panel

One 12-pin Digital I/O connector with 8-bit programmable I/O

Interface

One CPU fan connectors for fan speed controllable

Chipset

Frame Buffer

Display Type

Intel® Clear Video integrated HD Graphics Technology

Up to 1.7GB shared with system memory

CRT, LCD monitor with analog display

Onboard DVI interface

Onboard 20-pin DVI Connector

Ethernet Interface

Controller

Type

One Intel 82574L Gigabit Ethernet controller

One Intel 82579LM Gigabit Ethernet controller

(FS-A76TDG&FS-A76FTDG Only)

Triple speed 10/100/1000Base-T

Auto-switching Fast Ethernet

Full duplex, IEEE802.3U compliant

7 -

FS-A76 User’s Manual

Connector Two External RJ45 connectors with LED on rear I/O panel

Expansive Interface

PCI-Express

PCI

Audio Interface

One X16 and one X4 or X1 on PICMG 1.3 Interface

Four PCI bus master on PICMG 1.3 Interface

Chipset

Interface

Connector

Power and Environment

Intel® integrated Q77with Realtek ALC888HD Audio

Intel High Definition Audio compliance

2 channels sound output

Internal 10-pin header for line-out, MIC-in, 4-pin header for CD-IN

Power

Requirement

Dimension

Temperature

+5V, +12 DC input & 5VSB Requirement

338 (L) x 126 (W) mm

Operating within 0 ~ 60

O p

C (32 ~ 140

O p

F)

Storage within –20 ~ 85

O p

C (-4 ~ 185

O p

F)

Ordering Code

FS-A76TDG Onboard VGA, DVI, 8 x USB2.0, 6 x serial Port, 6 x SATA, HD Audio,

GPIO, 2 x PCI Express mini card, 4 x PCI Bus master,

1 x Giga LAN (82579LM)

Support Four X1 & One X16 PCI Express interface

FS-A76FTDG Onboard VGA, DVI, 8 x USB2.0, 6 x serial Port, 6 x SATA, HD Audio,

GPIO, 2 x PCI Express mini card, 4 x PCI Bus master,

1 x Giga LAN (82579LM)

Support One X4 & One X16 PCI Express interface

FS-A76TDG2 Onboard VGA, DVI, 8 x USB2.0, 6 x serial Port, 6 x SATA, HD Audio,

GPIO, 2 x PCI Express mini card, 4 x PCI Bus master, 2 x Giga LAN

Support Four X1 & One X16 PCI Express interface

FS-A76FTDG2 Onboard VGA, DVI, 8 x USB2.0, 6 x serial Port, 6 x SATA, HD Audio,

GPIO, 2 x PCI Express mini card, 4 x PCI Bus master, 2 x Giga LAN

Support One X4 & One X16 PCI Express interface

The specifications may be different as the actual production.

8 -

FS-A76 User’s Manual

1.3 <Mechanical Drawing>

9 -

FS-A76 User’s Manual

1.4 <Block Diagram>

3rd Generation Intel® Core™

I3/I5/I7/Pentium® processor

1 x PCI Express x 16

2 x 240-pin DDR3

1066/1333MHz up to

16GB

1 x DVI

1 x CRT

4 x USB 2.0

4 x USB 3.0

2 x Serial ports

W83627D-P

SPI BIOS

25Q64CV

IrDA

8-bit GPIO

Parallel port

Intel Q77

2 x PCI Express mini card

4 x SATAII & 2 x SATA III

1 x Intel 82574L & 1 x 82579LM

TPM

4 x RS232

1 x PCI Express x4 or

4 x PCI Express x1

4 x PCI Bus master

10 -

FS-A76 User’s Manual

SYSFAN

CPUFAN

CN_PS

DC_IN

CN_12V

JFRNT

Chapter 2 <Hardware Setup>

2.1 <Connector Location>

CN_USB1 DDR3_A&B

SATA1/2/3/4/5/6

CN_LPT

MINI_CARD1&2

CN_USB3_1

CN_USB3_2

CN_USB2

CN_DIO

CDIN

CN_AUDIO

JACT1

JSPD1

(FS-A76TDG & FS-A76FTDG)

CN_DVI

CN_SMBUS

CN_IR

COM6/5/4/3/2

(FS-A76TDG2 & FS-A76FTDG2)

FS-A76TDG2 & FS-A76FTDG2

PS2 RJ45_2 RJ45_1 CRT

FS-A76TDG & FS-A76FTDG

PS2 COM1 RJ45_1 CRT

COM6/5/4/3/2/1

JACT2

JSPD2

11 -

FS-A76 User’s Manual

2.2 <Jumper Location & Reference>

Jumper Function

JRTC

JAT

CMOS Operating/Clear Setting

Power mode select

JP1

JP2

JP3

JP4

JCSEL1

JCSEL2

JVUSB

Com1 Voltage Setting (For Pin 9)

Com2 Voltage Setting (For Pin 9)

Com3 Voltage Setting (For Pin 9)

Com4 Voltage Setting (For Pin 9)

CN_COM2 RS-232 RS422 RS485 Setting

CN_IR IrDA Setting

USB Voltage Setting

JRTC

JVUSB

JAT

JCSEL2 JP4 JP3 JCSEL1 JP2 JP1

JAT

Jumper: JAT

Type: Onboard 3-pin jumper

JAT

1-2

2-3

Default setting

1 3

Mode

AT Power mode

ATX Power mode

12 -

FS-A76 User’s Manual

2.3 <Connector Reference>

2.3.1 <Internal Connectors>

Connector Function Remark

CPU LGA1155

DDRIIIA&B 240 –pin DDR3 SDRAM DIMM socket

SATA 1/2

SATA 3/4/5/6

CN_12V

CN_AUDIO

7-pin Serial ATAIII connector

7-pin Serial ATAII connector

4-pin +12V additional power supply connector

5 x 2-pin audio connector

CDIN

CN_DIO

CN_USB 1/2

4-pin CD-ROM audio input connector

6 x 2-pin digital I/O connector

5 x 2-pin USB connector

CN_USB 3_1/2

CPUFAN

SYSFAN

CN_IR

10 x 2-pin USB connector

4-pin CPU cooler fan connector

4-pin system cooler fan connector

5-pin IrDA connector

CN_COM1/2/3/4/5/6 9-pin com connector

JFRNT 14-pin front panel switch/indicator connector

Mini-Card1/2

CN_LPT

JSPD 1/2

JACT 1/2

CN_DVI

2 x 52-pin Mini-PCIE socket

13 x 2-pin printer connector

LAN Speed LED connector

LAN Activity LED connector

13 x 2-pin DVI connect

2.3.2 <External Connectors>

Connector

RJ45 1/2

CRT

PS/2

(FS-A76G2 & FS-A76FG2)

Function

1 x RJ45 LAN connector

DB15 and analog VGA connector

PS/2 keyboard and mouse connector

Remark

Connector

RJ45 1

CRT

PS/2

COM1

(FS-A76G & FS-A76FG)

Function

1 x RJ45 LAN connector

DB15 and analog VGA connector

PS/2 keyboard and mouse connector

1 x DB9 connector

13 -

Remark

FS-A76 User’s Manual

2.4 <CPU and Memory Setup>

2.4.1 <CPU Setup>

FS-A76 has a LGA1155 CPU socket onboard; please check following steps to install the processor properly.

Attention If FS-A76 need RMA please Keep CPU socket cover on the CPU Socket.

Warning If CPU Socket internal Pin damage We could not provide warranty.

3rd Generation Intel® Core™

I3/I5/I7/Pentium® processor

Package type: 1155 pin FCLGA

FSB: 1066/1333MHz

1. Lift this bar Checked point

2. Uncover this plate

3. Place the CPU on the top of the pins

4. Lock this bar

3. Cover this plate

14

Notice: Please place the CPU on the pins tenderly to avoid bending the pins

FS-A76 User’s Manual

2.4.2 <Memory installation>

FS-A76 has two 240-pin DDR3 DIMM support up to 16GB of memory capacity. The memory frequency supports 1066/1333 MHz. Only Non-ECC memory is supported.

DDRIIIA&B

2.5 <CMOS Setup>

The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due

to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.

Jumper: JRTC

Type: Onboard 3-pin jumper

JRTC Mode

2-3 Normal Operation

Default setting: 2-3

JRTC

1 3

15 -

FS-A76 User’s Manual

2.6 <Serial ATA Interface>

FS-A76 has Four Serial ATA II & Two Serial ATA III interfaces with RAID function, the transfer rate of the Serial ATA II can be up to 300MB/s & Serial ATA III can be up to

600MB/s. Please go to http://www.serialata.org/ for more about Serial ATA technology information. Based on Intel® PCH, it supports Intel® Matrix Storage Technology with combination of RAID 0,1,5 and 10. The main features of RAID on Intel® Q77 PCH are listed below:

1. Supports for up to RAID volumes on a single, two-hard drive RAID array.

2. Supports for two, two-hard drive RAID arrays on any of six Serial ATA ports.

3. Supports for Serial ATA ATAPI devices.

4. Supports for RAID spares and automatic rebuild.

5. Supports on RAID arrays, including NCQ and native hot plug.

For more information please visit Intel’s official website.

For more about the system setup for Serial ATA, please check the chapter of SATA configuration.

SATA1/2

SATAIII

SATA//3/4/5/6

SATAII

16 -

FS-A76 User’s Manual

2.7 <Ethernet Interface>

The board integrates with one Intel 82574L Gigabit Ethernet & one Intel 82579LM controllers, as the PCI Express bus. The Intel 82574L supports triple speed of

10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported.

82574L 82579LM

FS-A76 TDG2 & FS-A76FTDG2

PS2 RJ45_2 RJ45_1 CRT

82579LM

PS2 COM1 RJ45_1 CRT

FS-A76TDG & FS-A76FTDG

17 -

FS-A76 User’s Manual

2.8 <Onboard Display Interface>

Based on Intel Q77 chipset with built-in graphics, the board provides one DB15

Connector on real external I/O port and the board also provides 20-pin DVI interface

Notice: When you install any PCI Graphic card, the onboard graphics would be disabled automatically.

2.8.1 <Analog Display>

Please connect your CRT or LCD monitor with DB15 male connector to the onboard

DB15 female connector on rear I/O port.

FS-A76TDG2 & FS-A76FTDG2

FS-A76TDG & FS-A76FTDG

CRT

CRT

18 -

FS-A76 User’s Manual

2.8.2 <DVI Display >

The board also comes with a DVI interface with Chrontel for digital video interface.

Connector: CN_DVI

Connector type: 20-pin header connector (pitch = 2.00mm)

Pin Number Assignment Pin Number Assignment

1 +5V 2 +3.3V

5 TMDSTX0N 6 TMDSTX0P

9 TMDSTX1P 10 Ground

11 TMDSTX2N 12 TMDSTX2P

15 TMDSTXCP 16 Ground

17 DVI_DA 18 DVI_SL

19 AUXN 20 AUXP

1 19

2 20

CN_DVI

19 -

FS-A76 User’s Manual

2.9 <Integrated Audio Interface>

The board integrates onboard audio interface with REALTEK ALC888 codec, with Intel next generation of audio standard as High Definition Audio, it offers more vivid sound and other advantages than former HD audio compliance.

The main specifications of ALC888 are: z z z z z

High-performance DACs with 100dB S/N ratio

2 DAC channels support 16/20/24-bit PCM format for 2 audio solution

16/20/24-bit S/PDIF-OUT supports 44.1K/48K/96kHz sample rate

Compatible with HD

Meets Microsoft WHQL/WLP 2.0 audio requirements

The board provides 2 channels audio phone jacks on rear I/O port, Line-in/MIC-in ports for front I/O panel through optional cable.

CN_AUDIO

10 9

CDIN

1 4

2 1

20 -

FS-A76 User’s Manual

Connector: CN_AUDIO

Type: 10-pin (2 x 5) header (pitch = 2.54mm)

Pin Description Pin

2 10

1

Description

9

1 MIC_L

3 MIC_R

5 Speaker_R

7 SENSE

9 Speaker_L

2 Ground

4 N/C

8 N/C

Connector: CDIN

Type: 4-pin header (pitch = 2.54mm)

Pin Description

1 CD – Left

2 Ground

3 Ground

4 CD – Right

4

1

21 -

10

CN_USB1

9

2 1

FS-A76 User’s Manual

2.10 <USB Interface>

FS-A76 integrates eight USB2.0 ports. The specifications of USB2.0 are listed below:

Interface

Controller

Transfer Rate

USB2.0

Intel® Q77

Up to 480Mb/s

Voltage 5V

AS-C76 integrates four USB3.0 ports. The specifications of USB3.0 are listed below:

Interface

Controller

USB3.0

Intel Q77 PCH

Transfer Rate Up to 5Gb/s

Voltage 5V

CN_USB3_1

CN_USB3_2

1 10

20 11

JVUSB

2 6

1 5

2

1

10

9

CN_USB2

22 -

FS-A76 User’s Manual

Connector: CN_USB1/2

Type: 10-pin (2 x 5) header (pitch = 2.54mm)

Pin Description Pin Description

1 VCC (5V_SB/ 5V)

3 Data0-

5 Data0+

7 Ground

9 Ground

4 Data1-

6 Data1+

8 Ground

Connector: CN_USB3_1/2

Type: 20-pin (2 x 10) header (pitch = 2.0mm)

Pin Description Pin Description

1 VCC 20 NC

2 USB3.0_RX0- 19 (5V_SB/ 5V)

3 USB3.0_RX0+ 18

4 Ground

5 USB3.0_TX0- 16

6 USB3.0_TX0+ 15

7 Ground

8 Data0-

9 Data0+

10 NC 11 Data1+

Jumper: JVUSB

Type: Onboard 6-pin jumper

JAT Mode

4-6 & 3-5 +5V_SB

2-4 & 1-3 +5V

Default setting

Effective patterns of connection: 1-3 & 2-4 or 3-5 & 4-6

2 6

1 5

2

1

6

5

Warning: others cause damages

23 -

FS-A76 User’s Manual

2.11 <Serial Port>

The board supports five RS232 serial port and one jumper selectable RS232/422/485 serial ports. The jumper JCSEL1 & JCSEL2 can let you configure the communicating modes for

COM2.

Connector: CN_COM1/3/4/5/6

Type: 9-Pin box header

Pin Description

1 DCD

3 TXD

5 GND

7 RTS

9 RI

Pin

CN_COM6/5/4/3/2/1

Description

2 RXD

4 DTR

6 DSR

8 CTS

10 9

2 1

Connector: CN_COM2

Type: 9-Pin box header

Pin Description Pin Description

1 DCD/422TX-/485- 2 RXD/422TX+/485+

3 TXD/422RX+ 4 DTR/422RX-

5 GND 6 DSR

7 RTS

9 RI

8 CTS

Setting RS-232 & RS-422 & RS-485 for COM2

24

FS-A76 User’s Manual

8 7 2 12

Function

2

8

1 1

2

1

8 7

2

IrDA

2

8

1

7

1

2

RS-232

2 1

Default setting:

RS-485

JCSEL1: (1-3, 2-4, 7-9, 8-10) JCSEL2: (1-2)

1

11

JCSEL1 11

12

11

12

11

Jumper: JP1/JP2/JP3/JP4 (COM1/2/3/4)

Type: onboard 6-pin header

Power Mode

Pin 9 with 5V Power

Pin 9 with 12V Power

Standard COM port

JP1/2/3/4

1-2

3-4

5-6

Default setting (5-6)

25

FS-A76 User’s Manual

2.12 <GPIO and SMBUS Interface>

The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK.

Connector: CN_DIO

Type: 12-pin (6 x 2) header (pitch = 2.0mm)

Pin Description

1 Ground

3 GP10

5 GP11

7 GP12

9 GP13

11 5V

Pin Description

2 Ground

4 GP14

6 GP15

8 GP16

12 12V

Connector: CN_SMBUS

Type: 5-pin header for SMBUS Ports

Pin Description

1 VCC

2 N/C

3 SMBDATA

4 SMBCLK

5 Ground

CN_SMBUS

1 5 2

1

CN_DIO

12

11

26 -

FS-A76 User’s Manual

2.13 <Power Supply and Fan Interface >

The FS-A76 provides a standard ATX power supply with 4-pin ATX connector and the board provides one 4-pin fan connector supporting smart fan for CPU cooler and one

4-pin cooler fan connectors for system and Northbridge chip. please connect this well before you finishing the system setup.

Connector: DC_IN

Type: 4-pin DC power connector

Pin Description

1 +12V

4

DC_IN

1

Pin Description

2 Ground

3 Ground 4 +5V

Connector: CPUFAN

Type: 4-pin fan wafer connector

Pin Description Pin

4

1

CPUFAN

Description

1 Ground

3 Fan Speed Detection

2 +12V

4 Fan Control

4

SYSFAN

1

Connector: SYSFAN

Type: 3-pin fan wafer connector

Pin Description

1 Ground

3 Fan Speed Detection

Pin Description

2 +12V

4 Will be defined

Connector: CN_PS

Type: 3-pin connector

Pin Description

1 5VSTBY

3

CN_PS

1

Pin Description

2 Ground

Pin

3

Description

PSON

27 -

FS-A76 User’s Manual

2.14 <Switch and Indicator>

The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.

Connector: JFRNT

Type: onboard 14-pin (2 x 7) 2.54-pitch header

Function Signal PIN Signal Function

IDE LED Power

LED

Reset

N/C

N/C

SPK-

Speaker

Power

Button

14

2

13

1

JFRNT

PWRBT+ 11

PWRBT- 13

12

14

28 -

FS-A76 User’s Manual

Chapter 3 <System Setup>

3.1 <Audio Configuration>

The board integrates Intel® Q77 with REALTEK® ALC888 code. It can support

2-channel sound under system configuration. Please follow the steps below to setup your sound system.

1. Install REALTEK HD Audio driver.

2. Lunch the control panel and Sound Effect Manager.

3. Select Speaker Configuration

29 -

FS-A76 User’s Manual

3.2 <Display Properties Setting>

Based on Intel Q77 with HD Graphic, the board supports two DACs for display device as different resolution and color bit.

Please install the Intel Graphic Driver before you starting setup display devices.

1. Click right button on the desktop to lunch display properties

2. Click Advanced button for more specificity setup.

30 -

Click Graphics Properties... for advanced setup

FS-A76 User’s Manual

3. This setup options can let you define each device settings.

Click Monitor to setup the CRT monitor for Resolution and

Refresh Rate

Click Intel® Dual Display

Clone to setup the dual display mode as same screen

31 -

FS-A76 User’s Manual

Chapter 4 <BIOS Setup>

The motherboard uses the Phoenix BIOS for the system configuration. The Phoenix

BIOS in the single board computer is a customized version of the industrial standard

BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.

The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory,

NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.

The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.

To activate CMOS Setup program, press <DEL> key immediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press

<Enter> key to accept the selection and enter the sub-menu.

Figure 4-1 CMOS Setup Utility Main Screen

32 -

FS-A76 User’s Manual

(This page is left for blank)

33 -

FS-A76 User’s Manual

Appendix A <I/O Port Pin Assignment>

A.1 <Serial ATA Port>

Connector: SATA1/2/3/4/5/6

Type: 7-pin wafer connector

1 2 3 4 5

7 1

6 7

GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND

A.2 <IrDA Port>

Connector: CN_IR

Type: 5-pin header for SIR Ports

Pin Description

1 VCC

2 N/C

3 IRRX

4 Ground

5 IRTX

JCSEL1 must jump to “SIR”

1

5

A.3 <VGA Port>

Connector: CRT

Type: 15-pin D-sub female connector on bracket

Pin Description Pin Description Pin

3

4

1

2

5

6

10

11

12

13

14

15

Description

1 RED 6 Ground 11 N/C

2 GREEN 7 Ground 12 DDCDA

3 BLUE

4 N/C

8 Ground

9 N/C

13 HSYNC

14 VSYNC

5 Ground 10 Ground 15 DDCCLK

A.4 <LAN Port>

Connector: RJ45

Type: RJ45 connector with LED on bracket

8 1

Pin 1 2 3 4 5 6 7 8

Description MI0+ MI0MI1+ MI2+ MI2- MI1MI3+ MI3-

34 -

FS-A76 User’s Manual

A.5 <LAN LED Port>

Connector: JSPD1/2

Type: 5-pin header for LAN Speed LED connector

When Lan speed 10/100Mbps

Pin Description

1 LED-

2 LED+

When Lan speed 1Gbps

Pin Description

1 LED+

2 LED-

Connector: JATC1/2

Type: 5-pin header for LAN Activity LED connector

2

Pin Description

1 LED-

2 LED+

2

1

1

A.6 <Parallel Port>

Connector: LPT

Type: 26-Pin box header

Pin Description

1 -PSTB

2 PRO0

3 PRO1

4 PRO2

5 PRO3

6 PRO4

7 PRO5

8 PRO6

9 PRO7

10 ACK-

11 BUSY

12 PE

13 SLCT

14

Pin

1

Description

23 Ground

24 Ground

25 Ground

26 N/C

26

13

35 -

FS-A76 User’s Manual

Appendix B <Programming GPIO’s>

The GPIO’can be programmed with the MSDOS debug program using simple IN/OUT commands.The following lines show an example how to do this.

GPIO0…..GPIO7 bit0……bit7

-o 2 E 87 ;enter configuration

-o 2E 87

-o 2E 07

-o 2F 09 ;enale GPIO function

-o 2E 30

-o 2F 02 ;enable GPIO configuration

-o 2E F0

-o 2F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output

-o 2E F1

-o 2F xx ;if set GPIO’s as output,in this register its value can be set

Optional :

-o 2E F2

-o 2F xx ; Data inversion register ; ‘1’ inverts the current valus of the bits ,’0’ leaves them as they are

-o 2E 30

-o 2F 01 ; active GPIO’s

For further information, please refer to Winbond W83627DHG-P datasheet.

36 -

FS-A76 User’s Manual

Appendix C <Programming Watchdog Timer >

The watchdog timer makes the system auto-reset while it stops to work for a period.

The integrated watchdog timer can be setup as system reset mode by program.

Timeout Value Range

- 1 to 255

- Second or Minute

Program Sample

Watchdog timer setup as system reset with 5 second of timeout

2E, 87

2E, 87

2E, 07

2F, 08

2E, 30

2F, 01

2E, F5

2F, 00

2E, F6

2F, 05

Logical Device 8

Activate

Set as Second*

Set as 5

* Minute: bit 3 = 0; Second: bit 3 = 1

You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.

37 -

FS-A76 User’s Manual

Appendix D <TPM Setup>

For further instruction about the Trusted Platform Module (TPM) function , please refer to the Commell_tmp_acronym_glossary_v010.pdf

.

Figure 4-1 TPM Setup Utility Main Screen

38 -

FS-A76 User’s Manual

Contact Information

Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us.

We will do our best to support you for your products, projects and business.

Taiwan Commate Computer Inc.

19F., No.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei

Address

City 22102, Taiwan

TEL +886-2-26963909

FAX +886-2-26963911

Website

E-Mail http://www.commell.com.tw

[email protected]

(General Information) [email protected]

(Technical Support)

Facebook https://www.facebook.com/pages/Taiwan-Commate-Computer-Inc/547993955271899

Twitter https://twitter.com/Taiwan_Commate

Commell is a brand name of Taiwan commate computer Inc.

39 -

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents