Rosborough RF-246
May 24 20xx Report Number xxxx
2000 Rosborough RF-246
Prepared for xxxxxx
xxxxxxxx
xxxxxxxx
John Bond Marine Surveyor SAMS®AMS®
Accredited Marine Surveyor
Pre-purchase and Insurance Marine Surveys
Email
1-905-885-6486
[email protected]
www.marinesurveyorontario.com
PO Box 72, Port Hope, Ontario, Canada L1A-3V9
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
1 of 12
May 24 20xx Report Number xxxx
TABLE OF CONTENTS
SECTION:
PAGE:
HULL, DECK, SUPERSTRUCTURE AND COCKPIT
CABIN APPOINTMENTS
FRESHWATER AND SANITATION
PROPULSION
ELECTRICAL SYSTEMS
ELECTRONICS AND NAVIGATION
SAFETY EQUIPMENT
4
5
5
6
7
7
7
FINDINGS AND RECOMMENDATIONS (*A *B or *C)
VALUATION
9
10
GENERAL INFORMATION
VESSEL DESCRIPTION
Most forward is the v-berth; next to port is a hanging locker, seating and the galley. Starboard side is
the head, helm, and dinette.
BUILDER: Rosborough Boats
Taxes not included
FAIR MARKET VALUE: $xxxxx CDN
OVERALL VESSEL RATING: xxx
FILE NUMBER:
WEATHER:
VESSEL NAME:
SURVEY TYPE:
LICENSE NUMBER:
HULL NUMBER:
SURVEY DATE:
USE:
AREA:
xxxxx
50' F and cloudy
none
C&V pre purchase
xxxxx
xxxxx
May 24 20xx
Pleasure
xxxxx
PBG-Power Boat Guide specifications
BW-Boat Watch power boat specifications
*-Per internet listing sheets (unverified)
FMS-From Manufacturer Specifications
FRP-Fiber Reinforced Plastic
**-Measured by surveyor
BEAM:
8' 6" FMS
DRAFT:
2' *
DISPLACEMENT:
5400 IBS FMS
LENGTH OVERALL: 25' FMS
FRESH WATER:
42 gallons FMS
HOLDING TANK:
33 gallons FMS
FUEL CAPACITY:
120 gallons FMS
FUEL TYPE:
Gasoline
PROPULSION: Twin Yamaha 50 HP outboard
motors
NA-Not available or not applicable
#-Per Certificate of Registry or vessel license
TC-Transport Canada
SS-Stainless Steel
CCG-Canadian Coast Guard
C&V Condition and Value
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
2 of 12
May 24 20xx Report Number xxxx
SCOPE OF SURVEY Acting at the request of xxxxx, the surveyor did attend onboard the
Rosborough on May 24 20xx in xxxxx Ontario, where an out of water inspection including the
underwater machinery and the exterior of the hulls wetted surface was performed.
A sea trial was not performed, the prospective owner attended, and the ship’s papers were not onboard
at the time of the survey. The Hull Identification Number (xxxxxx) was verified from the transom.
The reason for the survey was to ascertain the physical condition and estimated value of the vessel.
Moisture meter readings taken and referred to throughout the body of the report were taken with a
GRP 33. Ohmmeter readings taken and referred to throughout the body of the report were taken with a
Fluke 77 Multi meter. (DC) power was used to check the operation of the electrical systems specified
in this report. Machinery, tanks, belts, hoses, and piping were visually inspected where normally
accessible. No disassembly, sampling, analysis, compression testing, or pressure testing was
performed. Electronic equipment was checked for “Power up” only. This vessel was surveyed
without the removals of any parts, including fittings, tacked carpet, screwed or nailed boards, anchors
and chain, fixed partitions, instruments, clothing, spare parts, and miscellaneous materials in the bilges
and lockers, or other fixed or semi-fixed items. Locked compartments or otherwise inaccessible areas
would also preclude inspection. Owner is advised to open up all such areas for further inspection.
Further, no determination of stability characteristics or inherent structural integrity has been made and
no opinion is expressed with respect thereto. This survey report represents the condition of the vessel
on the above date, and is the unbiased opinion of the undersigned, but it is not to be considered an
inventory or warranty either specified or implied.
NOTE: It is recommend and understood that all GAS/DIESEL engines be surveyed by a qualified
Engine Surveyor to determine the condition of the engines, gears, pumps, heat exchangers, etc.
INTENDED USERS: The intended users of this report and valuation are xxxxx and underwriters
considering financing or insuring this vessel and is not transferable to any other person or entity.
STANDARDS USED: The mandatory standards contained in the Canada Shipping Act (CSA 2001)
and in particular, the small vessel regulations, TC Safe Boating Guide, Transport Canada TP1332
2010, the voluntary standards, and recommended practices developed by the American Boat and
Yacht Council (ABYC) National Fire Protection Association (NFPA) have been used as guidelines in
the conduct of this survey.
PERCUSSIVE SOUNDINGS: This is a low-tech, highskilled process in which structural members of fiberglass
boats are tapped on to determine their condition.
POWERS UP / POWERED UP: Power was applied only.
This does not refer to the operation of any system or
component unless specifically indicated
SERVICEABLE / ADEQUATE: Sufficient for a
specific requirement.
FIT FOR INTENDED USE: Use which is intended by
Survey Purchaser (present or prospective owner)
REMARKABLE: Noticeable.
OPERABLE: Fit / Operates. This does not refer that the
operation of a system or component was completely tested,
only that power was applied, or the system was activated.
UNREMARKABLE: Unnoticed, not noticeable.
USABLE: Capable of being used. Practicable for use.
GOOD CONDITION: Nearly new, with only minor
cosmetic or structural discrepancies noted.
Use of asterisks (*A *B or *C) in the body of the report will indicate that a finding will be
listed in the Findings and Recommendations section pertaining to the asterisked item.
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
3 of 12
May 24 20xx Report Number xxxx
HULL, DECK, SUPERSTRUCTURE, AND COCKPIT
TYPE/MATERIAL:
Displacement hull, FRP construction.
EXTERIOR HULL/TRANSOM:
Off white gel coat with blue accent stripes in better than the condition expected for a vessel of this age,
no dock rash, no exposed laminate. Two external swim platforms are fastened to the transom and
accessed from the cockpit by a step over transom. Percussive soundings and moisture meter readings,
where tested at random, are unremarkable.
BOTTOM:
Bottom is covered in grey colored anti fouling paint in usable condition. There was no readily
detectable visual evidence of hull bottom blistering. Percussive soundings where tested at random, are
unremarkable. Moisture meter readings were not taken where antifouling is applied, as they may be
unreliable.
BULKHEADS/STRINGERS:
Tabbing of bulkheads, partitions, and hull stiffeners where seen under the v-berth and salon sole
inspection ports, is smooth, secure, and tapped sound.
COCKPIT/DECK:
FRP fore deck, side decks, and cockpit have anti skid surface in the appropriate areas. Cockpit drain
hoses where seen were of marine grade and clamped. FRP style door gives access to the salon. Wrap
around windshield has an aluminum frame and operable vent window to the bow. Percussive
soundings and moisture meter readings, where tested at random, are unremarkable.
HULL TO DECK JOINT:
Bonded molded flange covered with a cap rail. No signs of structural damage to the hull to deck joint
where seen.
PULPITS/STANCHION/LIFELINES/HAND HOLDS:
Stainless steel tube handrail surrounds the forward weather deck; handholds are mounted on the cabin
and hardtop, all found to be secure and in good condition.
CHOCKS/CLEATS/ANCHOR PLATFORM:
*B1 Cleats and anchor roller were inspected and found to be secure and in good condition, exception
below.
Attention required;
Both aft cleats are loose.
HATCHES/PORT LIGHTS/WATER LEAKS:
Hatches and port lights serviceable, no signs of leaks seen.
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
4 of 12
May 24 20xx Report Number xxxx
ADDITIONAL EQUIPMENT/ACCESSORIES
Fenders and dock lines.
Cockpit enclosure is in good condition.
Dingy davit is securely mounted and in good condition.
Tandem axle bunk trailer, with brakes, a general inspection only.
Manufacturer from tag; Shoreland'r.
Trailer ID from tag; xxxxx.
Tires and Trailer are in good condition.
CABIN APPOINTMENTS
Galley contains a sink, hot and cold pressurized water system, Force 10 Propane stove top, and a 120volt AC / 12-volt DC Norcold fridge, model from tag DE451 using R 134A gas. FRP, wood trim
throughout and upholstery are in good condition. Each area has ample 12-volt DC lighting, operable.
PROPANE SYSTEMS:
PRESSURE GAUGE:
Seen
ELECTRIC SHUT OFF AT THE GALLEY:
Not seen
PRESSURE REGULATOR:
Seen
TANK / VENTING:
Tank venting seen
REGULATOR:
Seen
TANK SHUT OFF VALVE:
Seen
RELIEF VALVE:
Seen
FUEL LINES / FITTINGS:
CGA type 1 approved flexible fuel supply lines,
fittings swaged at the tank and appliance.
*B2 Attention required;
No propane shut off control or solenoid seen.
Always check fittings in the propane system for leaks with soap and water before spring launch.
GREY WATER
Galley sink drains directly overboard above the water line, hose where seen were of marine grade and
clamped.
FRESHWATER SYSTEM
Tank fill was found to be labeled correctly. Polyethylene type water tank is securely mounted under
the salon sole, as seen thru a small port. Hoses where seen were of marine grade polyester tubing and
clamped. Jabsco water pressure pump is securely mounted under the galley counter top; model from
tag: 30620-0012, operable.
HOT WATER HEATING
Securely mounted under the galley counter top is one 120-volt AC with built-in heat exchanger, 6
gallon hot water tank, manufactured by Seward: model from tag S-700, watts from tag: 1500.
Untested. The 150-psi Pressure relief valve was tested, operable.
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
5 of 12
May 24 20xx Report Number xxxx
SANITATION
*B3 Tank pump out was found to be labeled correctly. Polyethylene type waste tank is securely
mounted under the v-berth, no leaks where seen, aft end and top. Hoses where seen were of marine
grade and clamped. No bowl cracks were seen in the securely mounted Jabsco head.
Attention required;
Seawater supply ball valve to the head is loose in the hull.
PROPULSION
These Engine warning indicators are located at the helm; oil pressure light, and engine temperature
light.
ENGINES/DRIVES:
Two Yamaha outboard motors, model from tag: xxxxx, 4 cylinder, 4 stroke, 50 HP, electric starting,
gasoline engines driving one propeller per outboard.
Port
Starboard
Engine serial number from tag
xxxxx
xxxxx
Engine hours per meter
xxxxx
MOUNTS:
Outboard motors are securely fastened to the transom using two Armstrong brackets.
DRIVE TRAIN:
The exterior of the lower units was inspected visually and no signs of unusual external wear and tear
were noted. Two aluminum three bladed propellers were visually inspected only, and found to be in
good condition.
CONTROLS:
Manual throttle and shift cable controls are mounted at the helm, operable.
COOLING SYSTEM/EXHAUST:
Seawater system.
VENTILATION:
Fuel tank ventilation is provided by a ventilator on the port side using flexible ducting and one
Attwood 12-volt DC blower, operable.
FUEL TANK/SYSTEM:
One 5052 aluminum tank is securely mounted under the salon sole, as seen thru a small inspection
port. Fuel tank ground wires were measured with an ohmmeter and found to be with in specifications.
Fuel fill was found to be labeled correctly. Fuel check valve was seen at the tank. Fuel tank vent hose
is approved Type A1. Fuel lines thru the vessel are TC approved Type A1, after the transom,
manufacturer's hose. Fuel fill hose is approved Type A2. No visible fuel leaks in the system where
seen.
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
6 of 12
May 24 20xx Report Number xxxx
ELECTRICAL SYSTEM: (12-volt DC)
12-volt, DC power is supplied by three storage batteries, with one four-position marine type battery
switch. The batteries are contained in acid-resistant, non-conductive boxes; and secured from
movement. A regulated engine alternator with one Cruisair 40 amp automatic battery charger charges
the batteries. Wiring in general where seen is well routed and secure. There is a factory panel at the
helm using individual well-marked breakers per branch.
ELECTRICAL SYSTEM: (120-volt AC)
One 30-amp inlet, no arcing, or corrosion sighted. Shore power cord is in serviceable condition.
There is a factory panel at the galley with reverse polarity light using one main and individual wellmarked breakers per branch. Wiring where seen is marine grade boat cable well routed and secure.
Receptacle at galley is GFCI protected. The 120-volt AC grounding bus when checked with an
ohmmeter was found to be connected to the 12-volt DC engine negative terminal.
STEERING SYSTEM
Wheel steered, hydraulic helm, operated smoothly, stops were firm. One control station is located
starboard side of the cockpit.
ELECTRONICS AND NAVIGATION EQUIPMENT
RADAR:
SPEED/DEPTH SOUNDER:
NA
Ratheon ST60 speed and depth, powered up.
GPS:
VHF RADIO:
Raymarine C70 Chart Plotter, powered up.
Raymarine Ray 54, powered up.
AUTOPILOT:
ENTERTAINMENT:
NA
NA
SAFETY EQUIPMENT
It is the Master’s responsibility to ensure all required equipment is well maintained and carried
aboard at all times while underway.
Minimum Required Safety Equipment:
Pleasure craft 6-9m (19’ 8” - 29’ 6”)
1. One Canadian-approved personal flotation device or lifejacket of appropriate size for each person on board
seen onboard
2. One buoyant heaving line of not less than 15 m in length OR one approved lifebuoy with an outside diameter of 610
mm or 762 mm that is attached to a buoyant line of not less than 15 m / 49’ 3” in length.
not seen
3. A reboarding device if the freeboard of the vessel is greater than 0.5 m / 1’ 8”
seen onboard
4. One manual propelling device OR an anchor with not less than 15 m / 49’ 3” of cable, rope or chain in any
combination
seen onboard
5. One bailer or one manual water pump fitted with or accompanied by sufficient hose to enable a person using the pump
to pump water from the bilge of the vessel over the side of the vessel
not seen
6. A watertight flashlight
not seen
7. (6) Canadian approved flares of Type A, B or C
* exempt from carrying pyrotechnic distress signals if
Operating in a river, canal or lake in which it can at no time be more than one mile from shore; OR engaged in an
official competition or in final preparation for an official competition and has no sleep sleeping arrangements
not seen
8. A sound-signaling device or a sound-signaling appliance
seen onboard, horn, operable
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
7 of 12
May 24 20xx Report Number xxxx
9. Navigation lights that meet the applicable standards set out in the Collision Regulations if the pleasure craft is
operated after sunset and before sunrise or in periods of restricted visibility
operable
10. One magnetic compass (not required if the boat is 8m (26’ 3”) or less and operated within sight of navigational
marks)
seen onboard
11. Radar reflector
not seen, see notes below
12. One Class 5BC fire extinguisher, if the pleasure craft is equipped with a motor,
seen onboard
13. One class 5BC fire extinguisher if the pleasure craft is equipped with a fuel-burning cooking, heating or refrigerating
appliance
not seen
NOTE: A magnetic compass is not required to be carried on board a pleasure craft that is not more than 8 m in
length and that navigates within sight of seamarks.
NOTE: A reboarding device is required, unless the vertical height that must be climbed in order to re board the
pleasure craft is not more than 0.5 m
NOTE: Navigation lights are only required on a vessel that operates after sunset or in periods of restricted
visibility (fog etc)
NOTE: Radar reflectors are required for boat built of mostly non metallic materials. A radar reflector is not
required if:
The boat operates in limited traffic conditions, daylight and favorable environmental conditions, and where
having a radar reflector is not essential to the boats safety; or
The small size of the boat or its operation away from radar navigation makes having a radar reflector
impracticable.
NOTE: Flares are not required for a pleasure craft that: Is operating on a river, canal or lake in which it can
never be more than one (1) nautical mile (1.852 km) from shore.
AUXILIARY SAFETY EQUIPMENT
BILGE PUMPS:
One 12-volt DC Rule 1500, with float switch pump under the v-berth sole, operable in dry mode.
CO DETECTOR:
*C1 No CO detector seen.
SMOKE DETECTOR:
*C2 No smoke detector seen.
PROPANE FUME DETECTOR:
*B2 No propane fume detector seen.
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
8 of 12
May 24 20xx Report Number xxxx
FINDINGS AND RECOMMENDATIONS
Deficiencies noted under SAFETY should be addressed before vessel is next underway. These
findings represent an endangerment and or the vessel’s safe and proper operating condition. Findings
may also be of TC or CSA 2001 regulations.
"Existing pleasure craft that were constructed according to an earlier version of this standard (TC TP1332) are not required
by the regulations to comply with the current construction requirements of the Small Vessel Regulations, but are
encouraged to do so insofar as it is reasonable and practicable." Voluntary standards (ABYC / NFPA) may not have been
in effect, or may not have been adhered to by the builder, when the boat was constructed. Compliance is recommended.
Deficiencies noted under OTHER DEFICIENCIES should be corrected in the near future to maintain
standards and to help the vessel to retain its value.
A.
B.
C.
SAFETY DEFICIENCIES
OTHER DEFICIENCIES NEEDING ATTENTION
SURVEYORS NOTES AND OBSERVATIONS OR UPGRADES
Replace all rusty hose clamps with SS.
FINDINGS
TC safety equipment.
B1
Both aft cleats are loose.
B2
No propane shut off control or solenoid seen
No propane fume detector seen.
B3
Seawater supply ball valve to the head is loose in
the hull.
C1
No CO detector seen.
C2
No smoke detector seen.
RECOMMENDATIONS
Ensure all TC safety equipment is onboard before
spring launch.
Remove, reseal, and mount securely.
Recommend the installation of a 12-volt propane
gas detection and electronic control system.
Remove, reseal, and mount securely
Recommended.
Recommended.
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
9 of 12
May 24 20xx Report Number xxxx
VALUATION
It is the surveyor’s experience that develops an opinion of the OVERALL VESSEL RATING OF
CONDITION, after a survey has been completed and the findings have been organized in a logical
manner. The following is the accepted marine grading system of condition. The condition rating is a
comparison of vessels of similar make, model, and year.
EXCELLENT (BRISTOL) CONDITION, is a vessel that is maintained in mint or Bristol fashionusually better than factory new-loaded with extras-a rarity.
ABOVE AVERAGE CONDITION, has had above average care and is equipped with extra electrical
and electronic gear.
AVERAGE CONDITION, ready for sale requiring some maintenance and normally equipped for her
size.
FAIR CONDITION, requires maintenance to prepare for sale.
POOR CONDITION, substantial yard work required and devoid of extras.
As shown in the SYSTEMS AND FINDINGS AND RECOMMENDATIONS sections of this
REPORT OF SURVEY, and by virtue of my experience, my opinion is
OVERALL VESSEL RATING: xxxx
SURVEYOR’S CERTIFICATION:
I certify that, to the best of my knowledge and belief:
The statements of fact contained in this report are true and correct.
 The reported analyses, opinions, and conclusions are limited only by the reported
assumptions and limiting conditions, and is my personal, unbiased professional analyses,
opinions, and conclusions.
 I have no present or prospective interest in the vessel that is the subject of this report, and I
have no personal, interest or bias with respect to the parties involved.
 My compensation is not contingent upon the reporting of a predetermined value or direction
in value or direction that favors the cause of the client, the amount of the value estimate, the
attainment of a stipulate result, or the occurrence of a subsequent event.
 I have made a personal inspection of the vessel that is the subject of this report.
This report is submitted without prejudice and for the benefit of whom it may concern.
Attending Surveyor John Bond SAMS®AMS®
This report is invalid without the surveyors seal.
This report is invalid without the surveyors signature.
Date May 24, 20xx
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
10 of 12
May 24 20xx Report Number xxxx
STATEMENT OF VALUATION
This valuation is based on the vessels apparent condition on the date of the survey and assumes
that the vessels propulsion system and other equipment not proven during the survey inspection
are in fact operational. In addition, there is no warranty given, or implied, for the future use or
life of the propulsion system described within.
The FAIR MARKET VALUE is the most probable price in terms of money, which a vessel should
bring in a competitive market under all conditions requisite to a fair sale, the buyer and seller, each
acting prudently, knowledgeably and assuming the price is not affected by undue stimulus.
Currency converter used http://www.XE.com/ucc/
2000 - 2002 models for sale in Canada and the USA, different options, engines, with
or without trailers, asking
Low $40,000.00 High $64,000.00
FAIR MARKET VALUE: After consideration of reliability of the data, the extent of the necessary
adjustments and condition of the vessel, it is your surveyor’s opinion that the fair market value of the
subject vessel with trailer is
$xx,000.00 CDN (taxes not included)
xxxxxx CDN
In accordance with the request for a marine survey for the purpose of evaluating its present condition
and estimating its Fair Market Value, I herewith submit my conclusion based on the preceding report.
The subject vessel was personally inspected by the under signed. Subject to correction of deficiencies
listed as (A), the vessel is considered suitable for its intended use.
I certify that the hull identification number, which appears below on this document, was taken by the
undersigned on the date entered below. xxxxxx (image has been cropped and contrast adjusted)
Hull number goes here
Attending Surveyor John Bond SAMS®AMS®
Date May 24, 20xx
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
11 of 12
May 24 20xx Report Number xxxx
B3 ball valve loose in the hull
120-volt AC panel
Helm wiring, tidy
12-volt DC panel
batteries
cockpit
© Copyright 20xx E. & O.E., John Bond Marine Surveyor SAMS® AMS® "All rights reserved."
12 of 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement