Harman Infinity Reference 6001A Owner's Manual

Reference 6001A
Reference 10001A Amplifiers
FRONT
HI1
Bedienungsanleitung
DE
Manual de propietario
ES
Käyttöopas
FI
Mode d'emploi
FR
Manuale d'istruzioni
IT
Gebruikershandleiding
NL
Instrukcja obsługi
PL
Manual do utilizador
PT
Bruksanvisning
SV
Kullanıcı Kılavuzu
TR
欽䨪䩛ⱃ
ZH-CN
⢪欽罏䩛ⱁ
ZH-TW
Panduan Pengguna
ID
《䪔铡僇剅
JP
칺푷핞 컲졓컪
KO
0°
PHASE
FULL
LPF
180°
320HZ
320Hz
FREQ
FREQ
32Hz
32HZ
MAX
MAX
GAIN
GAIN
MIN
MIN
DC
TURN-ON
MODE
DA
0dB
HPF
X-OVER
LO
Betjeningsvejledning
12dB
BASS
BOOST
MIN
HI2
EN
SUB
MAX
GAIN
INPUT
LEVEL
Owner's Manual
HPF
X-OVER
EXT
INPUT
FULL
REM
LPF
INT
320Hz
FREQ
32Hz
REAR
v505a
INPUT
REMOTE
CONTROL
+
-
SUB
+
-
30A
FUSE
30A
+12V
REM
GND
PWR/PROT
L
R
Торговая марка:
JBL
Назначение товара:
Усилитель мощности
Изготовитель:
Харман Интернешнл Индастриз Инкорпорейтед, США, 06901 Коннектикут, г.Стэмфорд, Атлантик Стрит
400, офис 1500
Страна происхождения:
Китай
Импортер в Россию:
OOO «ХАРМАН РУС СиАйЭс», Россия, 127018, г.Москва, ул. Двинцев, д.12, к 1
Гарантийный период:
1 год
Информация о сервисных центрах:
www.harman.com/ru
Срок службы:
3 года
тел. +7-800-700-0467
Товар сертифицирован
Дата производства:
Дата изготовления устройства определяется по двум буквенным обозначениям из второй группы
символов серийного номера изделия, следующих после разделительного знака «-». Кодировка
соответствует порядку букв латинского алфавита, начиная с января 2010 года: 000000-MY0000000, где
«M» - месяц производства (А - январь, B - февраль, C - март и т.д.) и «Y» - год производства (A - 2010, B 2011, C - 2012 и т.д.).
Используйте устройство только по прямому назначению в соответствии с предоставленной инструкцией. Не пытайтесь самостоятельно
вскрывать корпус товара и осуществлять ремонт. В случае обнаружения недостатков или дефектов, обращайтесь за гарантийным обслуживанием
в соответствии с информацией из гарантийного талона. Особые условия хранения, реализации и (или) транспортировки не предусмотрены.
Избегайте воздействия экстремальных температур, долговременного воздействия влаги, сильных магнитных полей. Устройство предназначено
для работы в жилых зонах. Срок годности не ограничен при соблюдении условий хранения.
Reference 6001A
Reference 10001A Amplifiers
WHAT'S IN THE BOX
ACCESSING CONNECTORS AND CONTROL
PANEL
A
1. Slide the panel cover down
FRONT
GAIN
MIN
HI2
INPUT
LEVEL
HI1
BOOST
0dB
0°
HPF
X-OVER
FULL
PHASE
180°
LPF
LO
320HZ
320Hz
FREQ
FREQ
32Hz
32HZ
MAX
GAIN
MAX
GAIN
MIN
MIN
DC
TURN-ON
MODE
HPF
X-OVER
FULL
REM
LPF
EXT
INPUT
INT
320Hz
FREQ
32Hz
REAR
v505a
2. Remove panel cover
A
MOUNTING THE AMP
Note: It is recommended that you make all wire connections
before permanently mounting the amp.
EN
IMPORTANT: Disconnect the vehicle's negative (–) battery
terminal before beginning the installation.
EN
High-level signals
• Always wear protective eyewear when using tools.
• Choose a safe mounting location, away from moisture. Check
clearances on both sides of a planned mounting surface. Be
sure that screws or wires will not puncture brake lines, fuel
lines, or wiring harnesses and that wire routing will not interfere
with the safe vehicle operation. Use caution when drilling or
cutting in the mounting area.
• Choose a location that provides enough air circulation.
• Do not mount the amplifier with the heat sink facing downward,
as this interferes with cooling.
• Mount the amplifier so that it will not be damaged by the feet of
backseat passengers or shifting cargo in the trunk.
Loosen
Screws
Insert
Wires
DC
Tignten
Screws
INPUT
TURN -ON
MODE
REM
HI2
INPUT
LEVEL
HI1
LO
WIRING FOR POWER AND GROUND
At amplifier:
+12V
REM
GND
Stereo front or rear
speaker wires
Fuse holder, fuse
Chassis ground (–)
18” (46cm)
Battery
Remote turn-on to
aftermarket stereo REM out
(used only with low-level signal inputs)
Note: when using high-level signals, set the "
switch to " " and the "
" switch to " ". If no
sound plays, change the "
" switch to " ".
CONNECTING TWO REFERENCE 10001A
AMPLIFIERS FOR EXTRA POWER
At ground location:
Factory Bolt
Ring Connector
Ground Wire
To connect two Reference 10001a amplifiers, use an RCA patch
cable to connect the “PRIMARY OUT” of the primary amplifier to
the “SECONDARY IN” of the secondary amplifier. Set the Primary/
Secondary switch to “PRIMARY” on the primary amplifier, and to
“SECONDARY” on the secondary amplifier.
PRIMARY OUT
SECONDARY IN
AMP 1:
Note: Remove any paint
below ring connector
PRIMARY
Star Washer
MODE
SECONDARY
WIRING FOR INPUT SIGNAL
Low-level signals
DC
PRIMARY OUT
SECONDARY IN
INPUT
AMP 2:
TURN-ON
MODE
PRIMARY
REM
MODE
HI2
INPUT
LEVEL
"
SECONDARY
HI1
LO
From stereo subwoofer
low-level outputs
Note: when using low-level signals and remote turn-on lead, set the
"
" switch to "
" and the "
"
switch to " ".
WIRING FOR AUDIO OUTPUT
One subwoofer (4ohm/2ohm)
SETTING GAIN, CROSSOVERS, AND BASS
BOOST
Setting the gain
1. Start with
control set to minimum,
and the crossover control rotated midway.
+
-
MAX
2. Choose music with substantial bass
content.
MIN
3. Turn the volume control on your receiver to
¾ of its total output.
GAIN
Subwoofer
SUB
L
4. Adjust the
control clockwise,
listening carefully to the bass output. If
control
you hear distortion, turn the
counterclockwise to decrease the gain.
R
Two subwoofers (4ohm)
FREQ
+
-
Selecting the crossover frequency
Choose the crossover point to suit listening
320Hz preferences. Turn the dials to the left to lower
the crossover point and to the right to raise
32Hz
the crossover point. Exact crossover settings
depend on your listening preferences.
Subwoofer
L
SUB
0°
R
PHASE
180°
+
Selecting the subwoofer phase
Switch the
back and forth to
determine which setting provides the most
clean bass output.
Subwoofer
BASS
BOOST
CONNECTING THE REMOTE BASS
CONTROLLER
REMOTE
CONTROL
12dB
0dB
Selecting the bass boost
Adjust the
control clockwise or
counterclockwise to suit your taste.
SPECIFICATIONS
Reference 6001A
Power output @
4 ohms
Power output @
2 ohms
Frequency response
Reference 10001A
350 watts RMS x 1 600 watts RMS x 1
600 watts RMS x 1
1000 watts RMS
x1
10-320 Hz
10-320 Hz
32-320 Hz variable, 32 - 320Hz Variable,
Crossover frequencies
12 dB/ octave
12 dB/ octave
Line-level input
sensitivity
High-level input
sensitivity
200 mVrms 2.0 V rms
200 mVrms 2.0 V rms
2 Vrms - 20V rms.
2 Vrms - 20V rms.
Signal-to-noise ratio
>80 dB
>80 dB
THD+N @ rated
power
<1%
<1%
Fuse rating
30 A x 2
35 A x 3
Operating voltage
9~16 V
9~16 V
8-11/16" x 2-1/16" 12-5/8" x 2-1/16"
Dimensions (W x H x D) x 7-1/8" (220 mm x x 7-1/8" (320 mm x
51.3 mm x 180 mm) 51.3 mm x 180 mm)
Weight
Recommended wire
gauge
2.54 kg
3.58 kg
8
4
EN
TROUBLESHOOTING
No audio and POWER INDICATOR is off.
• No voltage at BATT+ and/or REM terminals, or bad or no
ground connection. Check voltages at amplifier terminals with
VOM.
No audio and PROTECT INDICATOR flashes every 4
seconds.
• DC voltage on amplifier output. Amplifier may need service; see
enclosed warranty card for service information.
No audio and PROTECT and POWER INDICATORS flash.
EN
• Voltage less than 9V on BATT+ connection. Check vehicle
charging system.
No audio and PROTECT INDICATOR is on.
• Amplifier is overheated. Make sure amplifier cooling is not
blocked at mounting location. Or, there may be voltage greater
than 16V (or less than 8.5V) on BATT+ connection. Check
vehicle charging system.
Amplifier fuse keeps blowing.
• The wiring is connected incorrectly or there is a short circuit.
Check wiring connections.
Distorted audio.
• Gain is not set properly. Check setting. Check wires for shorts
or grounds. Amplifier or source unit may be defective.
Distorted audio and PROTECT INDICATOR flashes.
• Short circuit in speaker or wire. Remove speaker leads one at
a time to locate shorted speaker or wire, and repair.
Music lacks dynamics or "punch".
• Speakers are not connected properly. Check speaker
connections for proper polarity.
Engine noise—whining or clicking—in system when the
engine is on.
• Amplifier is picking up alternator noise. First, check ground
connection on the amplifier – a loose or improper ground is
one of the main causes for noise. Turn down gain. Move RCA
audio cables away from power wires. Installing an alternator
noise filter on power line between battery and alternator might
also be necessary.
HARMAN International Industries,
Incorporated 8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.infinityspeakers.com
© 2019 HARMAN International Industries, Incorporated. All rights reserved.
Infinity is a trademark of HARMAN International Industries, Incorporated,
registered in the United States and/or other countries. Features, specifications
and appearance are subject to change without notice.
Infinity Reference 6001A_10001A_QSG_CR_V16
">