Miele PW 6101 Operating instructions

Miele PW 6101 Operating instructions
Operating Instructions
Washer
PW 6101
PW 6131
PW 6161
PW 6201
To prevent accidents
and machine damage
read these instructions
before installing or use.
UV
M.-Nr. 06 578 520
Contents
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operating panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1. Turn on the washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2. Sort and load the laundry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maximum dry laundry weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3. Add detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4. Select a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5. Select wash options (if needed). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6. Select Delay Start (if needed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7. Adjust the program (if needed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8. Start the program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9. End of program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Canceling a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Canceling a locked program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Skipping program cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Program sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
K Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Program end with water in the drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Program stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Program Guide Standard Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Washing using the program card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Card only operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Extra features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Language selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Optional modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Liquid dispensing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Peak load cutoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PC Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Load size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
After each use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cleaning the exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power failure - Emergency door release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Fault messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2
Contents
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Guide to the data plate symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Help to protect the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Removing the shipping struts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connecting the water intake / water drain hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3
IMPORTANT SAFETY INSTRUCTIONS
,WARNING
Read all instructions before installation or
use to prevent injury and machine
damage.
This washer-extractor is only intended for
laundry which has not come in contact
with flammable substances.
Dry cleaning solvents must not be used
in this machine. Such solvents could
cause a fire or explosion.
This appliance conforms to all uniform
safety codes and regulations. The
manufacturer cannot be held responsible
for damage or injury caused by improper
use of this appliance.
All personnel working with this machine
must be fully trained in its use and safety.
SAVE THESE INSTRUCTIONS AND
REVIEW THEM PERIODICALLY
4
Correct usage of the washer
Do not wash articles that have been
previously cleaned, washed, soaked or
spotted with gasoline, dry-cleaning solvents,
organic oils or other flammable substances.
These articles give off vapors that could
ignite or explode. Do not add these items to
the wash load.
CAUTION: Fire hazard!
Do not store or use gasoline, gasolinebased substances or any easily flammable
materials near the machine. Do not use the
top of the washer as a storage area.
Do not store any chemicals (liquid
detergents, wash aids) on the top of the
washer. The chemicals could damage the
surface. Spilled chemicals must be
immediately washed off with a wet sponge.
Under certain conditions, hydrogen gas
may be produced in a hot water system
that has not been used for 2 weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot
water system has not been used for such a
period, turn on all hot water faucets and let
the water flow from each for several minutes
before using the washing machine. This will
release any built-up hydrogen gas. Do not
smoke or use an open flame during this
time, the gas is flammable.
IMPORTANT SAFETY INSTRUCTIONS
Electrical Safety
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the
event of malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least resistance
for electric current.
Repairs to electrical or steam appliances
should only be carried out by a Miele
authorized technician in accordance with
local and national safety regulations.
Unauthorized repairs could cause injury or
machine damage. The manufacturer cannot
be held responsible for unauthorized work.
Do not repair of replace any part of the
appliance or attempt any servicing
unless specifically recommended in these
operating instructions. Contact Miele’s
Technical Service Department for
assistance.
Do not operate a machine with an
electrical fault until repaired.
Only use the washer if all panels are
properly in place.
The washer is only completely isolated
from the electrical supply when the
circuit breaker has been tripped or the
power main shut off.
Do not use force to open the washer
drum door. The door handle is equipped
with an extra safety mechanism to guarantee
that the door remains locked.
Faulty components must only be
replaced with genuine Miele spare parts
to guarantee the safe operation of this
machine.
Do not damage, remove, or bypass any
of the safety features and controls of the
washer.
5
IMPORTANT SAFETY INSTRUCTIONS
Use
Additional information
Do not let children play in, on or near the
washer. Do not let them play with the
controls or operate the unit. Close
supervision of children is necessary when
the appliance is used near children.
Disinfecting and cleaning agents often
contain chlorides (salts) which can
cause steel surfaces to rust. To protect the
machine from rust damage, only use
chloride free disinfecting and cleaning
agents for washing/disinfecting and for
cleaning the machine. If you are not sure
about an agent contact Miele’s Professional
Division. If you accidentally spill an agent
containing chloride on the machine it should
be rinsed off with water and dried with a soft
cloth.
The drum door glass will be hot when
washing at very high temperatures. Do
not touch the glass.
Do not reach into the appliance if the
drum is moving.
Do not drink washer water! Harmful
residues could be present.
Chlorine or agents containing chlorine
are corrosive and may cause permanent
damage to components of the machine.
Always follow the instructions of the
chemical manufacturer when using
cleaning agents and special application
chemicals. Only use such chemicals for the
purpose and in the situation specified by the
manufacturer. This will prevent the danger of
adverse chemical reactions and material
damage.
If in doubt, check with the manufacturer to
be sure that the product is suitable for use in
this machine.
Dyes, dye removers and descaling
agents may only be used in this machine
if the manufacturer states they are suitable
for use in a washing machine. Always
observe the manufacturer’s instructions
carefully.
Fabric softeners may be used with this
machine. Follow the manufacturers
instructions.
The manufacturer of the washer does not
take responsibility for the effect of the
chemical on the laundry or the machine
when a chemical cleaning agent is
recommended on technical application
grounds.
Keep the area around the machine clean
and free of debris.
Before the appliance is removed for
service or discarded, remove the door.
The interior of the machine should be
cleaned periodically by a qualified
service agent.
Using accessories
Only use genuine Miele accessories. If
other parts are used, guarantee,
performance and product liability claims
may become void.
Ensure that any one operating this
machine is familiar with these safety
instructions.
Do not use high pressure cleaners to
hose down the washer.
Check the hoses regularly for leaks to
prevent water damage.
Do not tamper with
the controls.
6
SAVE THESE
INSTRUCTIONS
Guide to the washer
a Detergent compartments
Pull the handle to open the flap.
d Drum door
e Door handle
b Control panel
c Emergency Stop button
Pull the door handle to open the drum door.
Do not use force.
Pressing the red button turns the machine
off.
The door handle is equipped with an extra
safety mechanism to guarantee that the door
remains locked.
7
Guide to the washer
Operating panel
a Display*
d Optical interface PC
1
Hot Wash
194 °F
2
Cottons
140 °F
3
Cottons Intensive
140 °F
i
FC
A
The optical interface on the machine’s
control panel provides the connection point
for data transfer between the machine’s
controls and a PC.
e Jog shuttle
The display will go into standby mode
10 min. after a program is started. The
display will fade. The circle illumination of
the h "Start" button lights up. By touching
any operating button or the jog shuttle the
display will switch back on (exception:
power failure or emergency stop button
used).
b Control keys
The control keys have different functions
depending on the machine status. The
functions are shown in the display above
each button.
If programed to "Button allocation direct", the
first 6 programs from the program list can be
selected directly with the control keys 1 to 6.
c h Start button
The circle illumination flashes if a selected
program can be started. To start a program
press the "Start" button. Once a program has
started the Start button can be pressed to
show the original display.
* Contents in the display will vary with
program offering.
8
Turn the jog shuttle to display selections
and input fields.
Press the jog shuttle to confirm display
selections or changes.
f Card reader
For card operation. Washing programs can
be uploaded and downloaded for the
machine on the program card. The
programs on the card can be used to
operate the washer.
g I On button
Turns the machine on.
h 0 Off button
Turns the machine off.
i Emergency Stop button
Only use in case of an emergency.
Press the red button to turn the machine off.
After clearing the danger, turn the button
clockwise to unlock it.
Press h "Start" again to continue the
interrupted program.
Guide to the washer
Control keys
e/- Following or previous line
^ Press once to activate the function, press
again to deactivate the function.
S Save
See the Programming manual.
i Manual operation
(Used by Miele Service Technicians)
See the Programming manual.
$ Program locked
If a program is locked it cannot be stopped
or ended with the Off-button after 1 minute.
FC Functions
Press this key to temporarily select another
language and/or access the operator level.
) Program unlocked
A Back to the previous display
+ i Block plus
The respective program block, e.g. prewash,
will be added to the program.
m Starch Stop
Press this button to stop the program and
allow starch to be added to the laundry.
k Spin Stop
Press this button if a final spin is not required
after the final rinse.
ß Dispensing
ä Dispensing not available
\ Operating data
-> l <- Reset to 0 (zero)
To reset the load sensor to "00.0" when the
drum is empty and the display shows a load
size.
D Data transfer
Operator Card
m Delay start
Press this key to select a start time in the
display.
K Information
To show program information
f Stop/Finish
Press to stop a selected program or to end
an already stopped program.
q Drain
ü Skip
Cycles of a program in progress can be
skipped or repeated.
No programs are saved on this card. To
transfer the data from the control to the card
and vice versa see the Programming
manual.
30 programs containing 6 blocks each can
be saved on the card.
The rear side of the card can be labeled.
9
Use
1. Turn on the washer
2. Sort and load the laundry
^ Open the on-site water valves (and the
supply valves for steam, if relevant).
^ Turn on the electrical supply at the mains
(on site).
^ Press l "On" to turn the washer on.
The welcome screen shows.
PROFESSIONAL
PW 6xx1
Welcome
^ Empty all pockets.
Then the program list is shown. The program
started last is highlighted.
1
Hot Wash
194 °F
2
Cottons
140 °F
3
Cottons Intensive
140 °F
i
ä
FC
Foreign objects left in pockets (e.g. nails,
coins, paper clips, etc.) can cause
damage to clothes and the machine.
^ Sort the laundry.
A
^ Only wash fabrics according to their wash
care label.
^ Open the drum door by pulling the handle.
^ Load the laundry loosely into the drum.
To prevent fabric damage, check that
laundry will not be caught in the closed
door.
^ Close the drum door with the handle.
Do not swing the door shut.
10
Use
Maximum dry laundry weights
3. Add detergent
PW 6101
23 lbs / 10 kg laundry
14 lbs / 6 kg wet cleaning
PW 6131
30 lbs / 13 kg laundry
18 lbs / 8 kg wet cleaning
PW 6161
36 lbs / 16 kg laundry
22 lbs / 10 kg wet cleaning
PW 6201
45 lbs / 20 kg laundry
27 lbs / 12 kg wet cleaning
^ Open the detergent compartment flap,
pull out the respective containers and add
detergent.
j = Detergent for the main wash
i = Detergent for a Pre-Wash
(1/4 of the total recommended amount
of detergent)
§ = Front compartment
Fabric softener or liquid starch
Rear compartment
Liquid additives e.g. bleach
^ Do not exceed the maximum fill level, the
excess will flow directly into the drum.
^ Close the detergent compartment.
11
Use
Detergent
Fabric softener
Only use the correct amount of high
efficiency low sudsing detergent. Too
much detergent will cause oversudsing.
Dosage
Follow the instructions on the detergent
packaging to ensure the correct usage and
dosage amount for your water hardness.
Adjust the amount of detergent if the load is
smaller and more or less soiled than normal.
Water hardness
Water
Water
Hardness
hardness quality
level in
levels
mmol/l
I
soft
0 - 1.3
II
moderate 1.3 - 2.5
III
hard
2.5 - 3.8
IV
very hard over 3.8
German
hardness
°d
0-7
7 - 14
14 - 21
over 21
If you do not know the water hardness in
your area contact your local water authority.
12
^ Pour liquid fabric softener into the
compartment according to the
manufacturer’s instructions. Do not
exceed the maximum fill level, the
excess will prematurely activate the siphon
and be wasted.
^ Close the compartment lid and push in the
dispenser drawer.
The fabric softener will automatically be
dispensed during the final rinse cycle.
A small amount of water will remain in the
compartment at the end of the program.
Never mix fabric softener and starch in
the fabric softener compartment §. This
will clog the dispenser.
Use
Starch
Bleach
In the detergent container
1
Hot Wash
Program stop - starch stop
Door can be opened.
i
ü
m
f
"Program stop - Starch Stop" flashes in the
display when it is time to add starch to the
laundry.
^ Add starch, prepared according to the
manufacturer’s instructions, into
compartment p. The wash time is
automatically extended by 4 minutes.
^ Press h "Start" to continue the program.
In the drum
Only bleach items with the x symbol on
the fabric care label.
^ Once the program stops in "Starch Stop",
open the drum door and add starch to the
laundry load prepared according to the
manufacturer’s instructions.
Liquid bleach can only be used in a
program designed for bleach.
^ Close the drum door.
The display shows:
1
Hot Wash
Program stop - Starch Stop
Door can be opened.
i
ü
m
f
^ Press the h "Start" button to continue the
program.
Liquid bleach must only be filled in a
programmed detergent compartment. It will
be automatically added to the second rinse.
A third rinse is necessary when using
bleach (see the Programming manual).
,The use of chlorine or chloric aids
lead to corrosion and may damage the
machine.
Fabric dye
Fabric dye and color aids must be suitable
for use in a washer. Always follow the
instructions of the manufacturer.
13
Use
4. Select a program
5. Select wash options (if needed)
^ Select a program by turning the jog shuttle
(e.g. Program 1 Hot Wash).
^ Press one of the wash option buttons.
To deselect the option, press it again.
The following will appear in the display:
+ i Block Plus
16
Extra Drain
1
Hot Wash
2
Cottons
194 °F
140 °F
ä
i
FC
A
^ See the Programming manual for more
information.
^ Confirm the selected program by pressing
the inner button of the jog shuttle.
The display shows:
1
Hot Wash
194 °F
Main wash
22.0 /22.0 lb
Rinse
+i
m
1200 rpm
k
m
A
A pre-wash can be selected for heavily
soiled laundry in certain programs. If a
pre-wash is an option the "+i" field is
highlighted. If a pre-wash is not available,
the "+i" will not be shown.
m Starch Stop
Starch can be selected with all standard
programs (excluding Extra Spin and Extra
Drain). The m field is highlighted in the
display.
k Spin Stop
Spin Stop can be selected with all standard
programs (excluding Extra Spin). The k
field is highlighted in the display.
1
Hot Wash
Program stop - w/o spin
Door can be opened.
i
ü
k
f
"Without spin" flashes in the display when the
spin cycle is reached.
^ Press the f "End" button.
^ The program ends without spinning.
^ To continue the program with spinning,
press the h "Start" button.
14
Use
6. Select Delay Start (if needed)
7. Adjust the program (if needed)
Use the m "Delay start" button to program
the washer to start automatically at a later
time.
Laundry weight
The laundry weight can be manually
selected.
Setting the delay start
^ Press m "Delay Start".
1
Hot Wash
104 °F
Pre-wash
The following will appear in the display:
194 °F
Main wash
+i
1
Hot Wash
Start time:
16
: 10
Start date: 2.4.2003
A
m
The display shows the current time of day
and date. The entry field is marked for
hours.
^ Press, then turn the jog shuttle to select
the hour. Press it to confirm the selection.
^ Repeat with the minutes, day, month and
year.
e
A
m
1
Hot Wash
194 °F
Main wash
22.0 / 22.0 lb
16:15 -2.4.2003
Start: 6:00 -3.4.2003
k
m
^ Turn the jog shuttle to "Laundry weight"
and press to confirm the selection.
The weight shown on the right side indicates
the max. weight.
^ Turn the jog shuttle to the desired laundry
weight and press to confirm the selection.
Temperature
In 1°F steps from cold to the maximum
program temperature.
^ Turn the jog shuttle to "Temperature"
(104 °F for Pre-wash) and press to confirm
the selection.
^ Press the h "Start" button to start the
program at the selected start time.
m
k
/ 22.0 lb
22.0 / 22.0 lb
After selection press the Start button.
+i
m
22.0
A
The display shows the current time of day,
date and the start time.
^ If the door is opened before the delay start
time has elapsed, press the h "Start"
button again.
1
Hot Wash
104 °F
Pre-wash
194 °F
Main wash
+i
m
22.0 / 22.0 lb
e
k
m
A
^ Turn the jog shuttle to the desired
temperature and press it to confirm the
selection.
Canceling the Delay Start
^ Press m "Delay Start" again or the
A "Back" button to cancel the delay start
function.
15
Use
Spin speed
8. Start the program
The spin speed can be adjusted from 0 300 then in 25 rpm increments. Depending
on the model of machine and the Program
selected the max. spin speed ranges from
600 - 1200 rpms.
^ Press the h "Start" button to start the
program.
^ Turn the jog shuttle to "Spin speed"
and press to confirm the selection.
1
Hot Wash
22.0 /
22.0 lb
Rinse
1200 rpm
-
9. End of program
At the end of the program, once the drum is
stationary and no water is in the machine the
display shows (for example):
1
Hot Wash
Program end
Door can be opened.
+i
m
k
m
A
^ Turn the jog shuttle to the desired spin
speed and press to confirm the selection.
m
FC
A
At the same time a tone will sound for a
short time to signal the program end.
^ Pull the door handle to open the drum
door.
Important:
If the door cannot be opened, press
against the door handle then pull again.
Do not use force!
^ Remove the laundry.
^ Leave the drum door open to air dry the
interior.
^ Turn the machine off with the 0 "Off" button.
^ Turn the mains off (on-site).
^ Close the gas or steam valve (on-site).
16
Use
Canceling a program
Canceling a locked program
To cancel a program, press the f "End"
button twice.
If the program was canceled with water in
the machine or during spinning, the display
shows:
Locked programs cannot be stopped or
canceled.
1
Hot Wash
194 °F
Main wash
Locked!
1
Hot Wash
End at 12:35
A
)
Program stop with water in the machine!
i
ü
f
The display shows that the program is
locked if the f "End" button is pressed.
To unlock the program press the ) "Unlock"
button.
or
1
Hot Wash
Program stop - drum not stationary!
i
ü
f
Press the q "Water drain" button or select
the program Extra Spin, and press the h
"Start" button.
Enter the password, by turning the jog
shuttle to the desired character in the alpha
numeric list and then pressing the shuttle to
confirm each selection.
After entering the password the display
shows:
Unlock program?
S
A
Press the S "Save" button to confirm. The
normal display shows and the program can
be canceled.
1
Hot Wash
194 °F
Main wash
140 °F
Rinse 1
End at 12:35
m
K
f
17
Use
Skipping program cycles
Program sequence
Cycles of a program in progress can be
skipped or repeated.
The program sequence is shown in the
display after the start of the program.
^ Press the f "End" button to stop the
program.
1
ü
f
^ Press the ü "Skip" button. The display
shows the current area, block or step.
68 °F
Program stop
S
e
A
Area: 2 Main wash
Block 1: Main wash
Step: Wash time 2
S
k
A
^ Turn the jog shuttle to "Area" and press it to
confirm the selection.
Area: Select either 1 Prewash, 2 Main
wash or 3 Rinse and confirm by pressing
the jog shuttle.
^ Turn the jog shuttle to "Block" and press it
to confirm the selection.
Block: Select either Prewash 1-10, Main
wash 1-10 or Rinse 1-10 and confirm by
pressing the jog shuttle.
^ Turn the jog shuttle to "Block" and press it
to confirm the selection. Select the desired
program step and confirm.
^ To start the new program step press S
"Save" and h "Start".
To go back without skipping a program
cycle
^ Press the A "Back" to go back to the
program stop.
m
K
f
The second display line, here Pre-wash, the
wash water temperature is shown.
1
Hot Wash
194 °F
Main wash
+i
-> 1 Hot Wash
Area 2: Main wash
m
End at 12:35
140 °F
Rinse 1
See also "Program structure" in the
Programming manual .
18
Pre-wash
+i
Program stop
Skip
Hot Wash
Main wash
Hot Wash
i
1
104 °F
m
Cold
k
m
End at 12:35
K
f
If the program block Pre-wash has ended,
the 2nd line in the display shows the
program block Main wash with the current
wash water temperature. The 3rd line shows
the following program block, here Rinse 1.
The program end display, above 12:35,
shows the time of day when the program will
be finished.
Use
K Information
1
Hot Wash
194 °F
Main wash
Program end with water in the drum
140 °F
Rinse 1
+i
Cold
m
k
m
End at 12:35
K
f
If the program is interrupted during a cycle,
the display shows either:
1
Hot Wash
Program end - Water in drum
Press the K "Information" button during the
program to show information in the display.
1
Delay start: 10.7.2003
e
A
1
Program end - Drum not stationary
m
Time left: 0 h 11min
A
Do not use force!
e
^ Press the q "Water drain" button or select
the Drain Extra and press h "Start".
Time left: 0 h 11min
Repetition: no
Block 2: Rinse
FC
,The drum door is locked.
Time after start: 0 h 23 min
e
Area: Rinse 3
A
Hot Wash
For more information press e.
Time after start: 0 h 23 min
FC
or
Hot Wash
Start time: 9:47
m
^ At the end of the program open the door.
2
Block step Wash time 1
Actual water level: 22 mm
e
Program stop
^ To stop the program, press f "End".
Programmed value: 60 mm
The program stops.
Actual temperature: 95°F
Programmed temperature: 140 °F
e
1
Hot Wash
Program stop
1
Hot Wash
Revolution: 40 rpm
Rhythm: 12 / 3
i
A
^ Press the A "Back" button to return to the
program sequence.
ü
f
^ Press f "End" again to continue the
program.
19
Program Guide Standard Programs
Programs may vary depending on machine type.
Program /
Display
Fabric
Program cycle
Wash
options
1 Hot Wash
194 °F
Bed linens and terry cloth
laundry made of cotton,
linen or mixed fabrics
Pre-wash 104°F selectable
Main wash 194°F
2 x Rinse
last rinse warm*
Final spin
+i
m
k
2 Cottons
140 °F
Lightly soiled bed linens
and terry cloth laundry
made of cotton, linen or
mixed fabrics
Pre-wash 86°F selectable
Main wash 140°F
2 x Rinse
last rinse warm*
Final spin
+i
m
k
3 Cottons
intensive
140 °F
Bed linens and terry cloth
laundry made of cotton,
linen or mixed fabrics
Pre-wash 86°F selectable
Main wash 140°F
2 x Rinse
last rinse warm*
Final spin
+i
m
k
4Cottons
86 °F
Lightly soiled bed linens
and terry cloth laundry
made of cotton, linen or
mixed fabrics
Pre-wash 86°F selectable
Main wash 86°F
2 x Rinse
Final spin
+i
m
k
5 Cottons
intensive
86 °F
Bed linens and terry cloth
laundry made of cotton,
linen or mixed fabrics
Pre-wash 86°F selectable
Main wash 86°F
2 x Rinse
Final spin
+i
m
k
6 Wrinkle Free
140 °F
Lightly soiled synthetics
and mixed fabrics
Pre-wash 86°F selectable
Main wash 140°F
2 x Rinse
Final spin 1 Min.
+i
m
k
7 Wrinkle Free
intensive
140 °F
Synthetics and mixed
fabrics
Pre-wash 86°F selectable
Main wash 140°F
2 x Rinse
Final spin 1 Min.
+i
m
k
8 Wrinkle Free
86 °F
Lightly soiled synthetics
and mixed fabrics
Pre-wash 86°F selectable
Main wash 86°F
2 x Rinse
Final spin 1 Min.
+i
m
k
9 Wrinkle Free
intensive
86 °F
Synthetics and mixed
fabrics
Pre-wash 86°F selectable
Main wash 86°F
2 x Rinse
Final spin 1 Min.
+i
m
k
20
Program Guide Standard Programs
10 Delicates
Synthetics, silk, rayon
11 Woolens
86 °F
Machine washable woolens, Main wash limited to 104°F
Wash rhythm "gentle"
sturdy woolens and mixed
2 x Rinse
woolens
Final spin 1 Min.
12 Handwash
Woolens
86 °F
Woolens and mixed woolens Main wash limited to 86°F
Wash rhythm "gentle"
2 x Rinse
Final spin 1 Min.
Pre-wash selectable
Main wash 86°F
Wash rhythm "delicate"
2 x Rinse
Final spin 1 Min.
+i
m
k
m
k
m
k
13 Extra
Starch
14 Extra
Rinse /
Spin
Laundry which needs to be
rinsed and spun
Rinse
Final spin
15 Extra Spin
Laundry which needs to be
spun
Final spin
16 Extra
Drain
m
k
Water drain
* Warm rinse
The standard programs 1 Hot Wash 194°F, 2 Cottons 140°F and 3 Cottons Intensive 140°F are
programmed to rinse with hot water. If a hot water connection is available, it is favorable to use
this.
- The residual moisture of the laundry is lower after spinning.
- The laundry is already warmed.
If the laundry is immediately dried in a dryer or ironed with the rotary iron, time and energy is
saved.
To deselect the warm rinse, see the Programming manual.
21
Washing using the program card
Program cards are programmed to a
machine type. Empty cards can be used
with any machine.
If the card was inserted the wrong way, the
display shows:
^ Press l "On" to turn the washer on.
§
The Welcome screen shows.
Card error
Reinsert card correctly in card reader.
Continue: Press Start.
i
ü
f
^ Reinsert the card properly into the card
reader.
If the card is not suitable for this type of
machine, the display shows:
Card operation
Programs on the card are only
suitable for machine type
A
^ Insert a card suitable for this machine
type.
Card only operation
^ Insert the card, arrow first, into the card
reader.
The display shows the list of programs on
the card, example:
Card operation
17
Fire department clothing 113 °F
18
Wrinkle-free
i
ß
140 °F
FC
A
^ Turn the jog shuttle to select a program.
Press the jog shuttle to confirm the
selection.
^ Press the h "Start" button to begin the
program.
^ Remove the card from the card reader.
Once the program is finished it will be
deleted from the machines memory.
,Do not insert any items other than the
card into the card reader.
22
A card with one particular program is
enclosed for laundry with special treatment
needs.
The function "Load" can be activated in the
operator level. The machine will only accept
cards in this function.
Those cards contain only one program. The
programs saved in the machine control are
not accessible.
Extra features
Language selection
The language can be selected with the F
flag symbol. The language is set back to its
original setting 5 minutes after the program
ends or when the door is opened.
1
Hot Wash
194 °F
2
Cottons
140 °F
3
Cottons Intensive
140°F
i
FC
A
Press the function button FC. The display
shows:
Settings
Back A
Main menu
Language
Operator level
FC
A
^ Turn then press the jog shuttle to select
"Language".
Settings
Back A
Language
Deutsch
English
FC
A
^ Turn the jog shuttle to select the desired
language and press to confirm the
selection.
23
Optional modules
Liquid dispensing system
Deselect the dispensing
(Dispensing systems vary)
1
Hot Wash
194 °F
2
Cottons
140 °F
3
Cottons Intensive
140 °F
ä
i
FC
A
The liquid dispensing can be manually
deselected before a program start.
The dispensing pump is turned off.
The display shows:
1
Hot Wash
194 °F
Main wash
22.0/22.0 lb t
Rinse
+i
a b c
m
1000 rpm
k
m
A
Dispensing amount
d
e
chemical manufacturer when using
cleaning agents and special application
chemicals.
Priming the dispensing pumps
a Hose connection socket (in)
b Leakage outlet
Only use such chemicals for the purpose
and in the situation specified by the
manufacturer to prevent the danger of
adverse chemical reactions and material
damage.
c Hose connection socket (out)
d Suction inlet opening
e Level indicator
When the dispenser container is empty the
pump and the machine will shut off.
The display will indicate that the detergent
dispenser is empty.
Fill dispensing container 1
Press Start.
i
f
^ Refill the dispensing containers.
^ Press h "Start" to continue the program.
24
If in doubt, check with the manufacturer
that the product is suitable for use in this
machine.
Liquid detergent should stand at room
temperature before being used to ensure
proper dispensing.
Dispensing system fault
ö
,Always follow the instructions of the
Optional modules
Priming the dispensing pumps
Use the calibration to get liquid detergent to
the pumphead. Once calibration is complete
run an empty program to get detergent to
the machine before actually washing a load
of laundry in the machine.
Dispensing calibration
Dispensing calibration
Dispensing pump 1
Dispensing pump 2
e
A
^ Select the dispensing pump.
Dispensing calibration
V: 100ml
The dispensing calibration is used to
calculate the flow rate of each single
dispensing pump.
Main menu
Dispensing pump 1
t: 0s
no
0/1
Direct access to the dispensing calibration
when the machine is turned off:
^ Press and hold the 2nd control key.
S
A
^ The dispensing can be manually stopped
by pressing the 0/1 button or it will stop
automatically after 60 seconds.
^ Measure the pumped amount in the
measuring cup.
^ Turn the machine on at the mains.
Dispensing calibration ~ Main menu
Dispensing calibration
Dispensing pump 1
e
A
Dispensing pump 2
V: 100ml
Dispensing pump 1
t: 30s
P: 200.0 ml/min
0/1
S
A
Selections: Dispensing pump 1 to 13
^ Enter the measured amount in the "V:" field.
The flow rate P is calculated by the control.
After selecting a dispensing pump the
display shows:
^ Press S "Save" to allocate the measured
values to the dispensing pump.
Dispensing calibration ~ Dispensing pump 1
V: 100ml
t: 0s
P: 200.0 ml/min
0/1
S
A
The dispensing amount can be adjusted in
1 ml increments from 0 to 999 ml.
^ Press the control key 0/1, the dispensing
hose fills. Press the 0/1 button again to
stop.
^ Hold the hose, of the dispensing pump to
be determined, in a measuring cup.
,Avoid skin and eye contact, wear
protective clothing.
^ Press A to get back to the main menu.
^ Reconnect the hose.
Maintenance of the dispensing system
^ Rinse the dispensing system with hot
water every 2 weeks, or before shutting
down the dispenser pumps for any length
of time, to prevent the system from
clogging.
^ Rinse out the suction pipes with water.
^ Place the suction pipes in a container with
warm water, 104 - 122°F (40 - 50°C).
^ Select each pump by using the dispensing
calibration.
^ Turn on each pump until the dispensing
system is rinsed.
^ Check the connection points, hoses and
washers for leaks.
25
Optional modules
Peak load cut off
Load size
When activating the peak load cut off the
heat is turned off and the program is
stopped. The display shows:
If the machine is equipped with a load
module, the load weight will be displayed, in
0.5 lb increments, while loading the laundry.
The maximum laundry weight is displayed
next to the selected program.
1
Hot Wash
Program stop by peak load function
The program continues.
i
ü
f
When the peak load function ends the
program will continue automatically.
^ Reset with the -> I <- "zero setting" if the
weight display does not show "00.0" when
the drum is empty.
1
Hot Wash
140 °F
Main wash
00.0 /
16 lb
e
A
Rinse
+i
PC Connection
m
k
m
-> I <-
If there was still laundry in the drum when
the weight display was reset, the display
shows:
1
Hot Wash
140 °F
Main wash
/
- - .-
16 lb
Rinse
+i
A serial interface is located at the rear of the
washer to connect the machine to a PC
(Personal Computer).
PC-Operation: Program changes can be
made via a PC, or a new program can be
downloaded.
Printer-Operation:
It is possible to print out whole programs or
parts of programs.
This requires a special Editor Program which
is available from the Miele Professional
Department.
m
k
m
-> I <-
e
A
^ Reset again with the -> I <- button.
If the machine is overloaded (wet laundry)
the machine calculates after the programs
start with the nominal value. This value is
saved in the operating data module.
At the end of a program, with the drum
stationary, the residual moisture of the
laundry is displayed.
1
Hot Wash
Program end
Residual moisture 60 %
Door can be opened..
m
FC
A
See "Use - Adjust the program" for more
information.
26
Cleaning and Care
After each use
Cleaning the drip channel and siphon
Never use high pressure cleaners to hose
down the machine.
The machine should be cleaned immediately
after use.
^ After use do not shut the drum door, allow
the interior to air dry.
Cleaning the exterior
,Never use abrasive cleaners, scouring
pads, steel wool or caustic cleaners on
the machine. They will damage the
surface.
All surfaces can be cleaned with a solution
of warm water and liquid dish soap applied
with a soft sponge.
^ Insert a small screwdriver into the hole on
the right side of the detergent flap.
^ Push it in horizontally until the hinge
disengages.
^ Take the detergent flap off.
Door gasket
^ Clean the drip channel and the siphon.
The siphon can be cleaned with a bottle
brush.
^ Clean any residues on the door gasket
with a damp cloth.
Detergent containers and siphon tube
Stainless steel
^ Regularly clean detergent residues from
the detergent dispensers, drawers and
siphons with warm water.
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel cleaner.
To help prevent resoiling, a conditioner for
stainless steel can also be used.
^ Pull the siphon tube out, clean it with warm
water and reinsert it.
^ Apply sparingly with even pressure.
27
Cleaning and Care
Vent grille
Water inlet filters
^ Regularly check and clean the wash water
vent grille at the rear of the machine.
Rust
The drum and the wash water drum are
made of stainless steel. Water with a high
iron content or items like paper clips or iron
buttons which are in the laundry, can lead to
rust in the drums.
^ To help prevent rust, a conditioner for
stainless steel can be used.
^ Check the door gasket for iron residue and
clean with stainless steel conditioner.
^ Clean regularly.
Leave the drum door open after use for
the interior to air dry.
^ Regularly check and clean the filters in the
water intake valves, 1, and the water intake
hoses, 2.
Maintenance during downtime
^ When the machine is not used for an
extended time (4 weeks or more), the
drum needs to be rotated manually a
couple of times to prevent bearing
damage. Repeat every month.
28
Cleaning and Care
Drum bearing lubrication
(PW 6161 and 6201 only)
Maintenance during downtime
If the machine needs to be serviced the
following message shows:
DRUM BEARING LUBRICATION!
§
When the machine is not in use for an
extended time (4 weeks or more), the drum
bearings must be lubricated (before the
downtime).
^ Lubricate the drum bearings according to
the warning message and turn the drum
by hand a few times.
Call the Miele Service
Department.
A
^ Press A "back" to delete the message.
^ Repeat every month to prevent bearing
damage.
The message will show each time the
machine is turned on, until a Service
Technician has serviced the machine.
^ After about 1000 operating hours, lubricate
the drum journal bearings with the
lubricating nipple using Arcanol L 100
grease.
29
Frequently asked questions
Reasons for oversudsing
The drum door cannot be opened
Detergent type
^ Press against the door handle, turn the
machine on then off and pull on the door
handle once more.
^ Only use detergent formulated for use in
commercial washers. Detergents for
domestic machines are not suitable.
Too much detergent
The safety mechanism of the door
handle is disengaged
^ Follow the detergent manufacturer’s
instructions and adjust the amount to the
local water hardness.
Oversudsing detergent
^ Use a low sudsing detergent or contact
Miele’s detergent application specialists.
Very soft water
^ In areas with soft water, use less
detergent.
Soiling level of laundry
^ For lightly soiled laundry use less
detergent.
The door handle has lost its function. The
door cannot be opened or closed.
The safety mechanism is designed to
protect the handle from damage, i.e. if too
much force is being used in an attempt to
open the door.
Residue, e.g. undissolved detergent on
laundry
^ Run a prewash without detergent and
without selecting a temperature.
^ Laundry which has been pre-treated in
detergent before washing must be
thoroughly rinsed before running a wash
program.
Small loads
^ Reduce the amount of detergent
dispensed accordingly.
Drum speed too high during a wash
(Profitronic-controls)
^ Reduce the drum speed and wash rhythm.
30
^ Firmly press against the door handle until
you hear the safety mechanism click.
The door can now be opened or closed
provided there is no water in the machine.
Frequently asked questions
Power failure - Emergency door
release
Draining the wash water
During a short power failure
The program remains in the last position.
When power is restored the following
message appears in the display:
y
^ Place a container under the manual drain
at the rear of the machine.
^ Open the drain by loosening the venting
screw. Do not take it completely out.
^ A small amount of water from the machine
will drain.
Power failure
^ Tighten the venting screw again and test
for leaks by opening the water supply.
Program stop
Press Start.
f
Open the door manually
^ Press h "Start" to continue the program.
Extended power failure
^ Turn the machine off.
^ Turn the electrical supply off at the mains.
^ Close the steam valve (on-site).
The machine must be drained and the drum
door opened manually to unload the
machine.
^ Insert and hold a small screwdriver in the
opening next to the door lock.
^ Press against the door handle, then pull it
towards you to open the door.
Do not use force!
^ Remove the laundry.
31
Frequently asked questions
Display Service interval
Fault messages
^ Call Technical Service for maintenance if
the display shows the following message
after turning the machine on.
§
Service interval 1
Call the Miele Service Department.
A
The display goes out after 5 seconds.
,Repairs to electrical or steam
appliances should only be carried out by
a Miele authorized technician in
accordance with local and national safety
regulations. Unauthorized repairs could
cause injury or machine damage. The
manufacturer cannot be held responsible
for unauthorized work.
Faults that occur before or after the start of a
program flash in the display.
If the display remains off, the dryer has no
power.
^ Check the plug, main switch and fuses
on-site.
y
Power failure
Program stop
Press Start.
f
^ Press h "Start".
This fault message can also indicate that the
overload cut-out of the drive motors has over
heated.
^ Allow the motor to cool.
32
Frequently asked questions
M
Water intake fault
q
Call the Miele Service Department.
if restart is without success.
i
f
i
A defective drain valve should only be
replaced by an authorized service
technician.
Program Stop
Press Start.
Dispensing system fault
f
ö
^ Press h "Start" to continue the program
without heating.
If the program has a "Thermostop" the
program will time out.
Fill dispensing container 1
Press Start.
i
f
^ Change/fill the dispensing container.
^ Call Miele Technical Service.
^ Some programs may be canceled if this
messages shows.
Call Technical Service.
m
f
^ Check and clean the drain system and
press h "Start".
Heating system fault
i
Call the Miele Service Department
if restart is without success.
^ Check the water supply and press h
"Start".
§
Drain error
Motor system error
§
Card error
Reinsert card correctly in card reader.
Continue: Press Start.
i
f
^ Insert the card properly into the card
reader.
Program stop. Press Start.
Motor temperature too high.
i
f
^ Allow the motor to cool.
§
Imbalance fault
Call the Miele Service Department
if restart is without success.
i
A
Large imbalance, the imbalance switch has
activated.
^ Turn the machine off and on again
^ Press h "Start".
33
After sales service
In the event of a fault which you cannot
correct yourself, please contact:
Miele Technical Service
800-991-9380
[email protected]
When contacting Technical Service please
quote the model (M.-Nr.) and serial number
(Fabr.-Nr.) of the machine. These can be
found on the silver data plate:
Above the drum opening,
or on the back panel of the machine.
When calling Miele Technical Service report
the error in the display.
Only use original Miele spare parts when
performing maintenance or repairs on this
machine.
34
Guide to the data plate symbols
1 Machine type
15 Electric heating
2 Serial number/Year of production *
16 Fusing (on site)
3 Voltage/Frequency
17 Steam heating indirect
4 Fuse rating
18 Steam heating direct
5 Drive motor
19 Gas heating
6 Plate diameter/Plate quantity *
20 Commissioning date
7 Drum data
8 Drum diameter/Drum depth
21 Water-Registration
DVGW-test cert (Water)
9 Spin speed
22 Field for CE test symbol
10 Drum volume/Laundry dry weight
11 Kinetic Energy
Noise level
12 Ex. time to top speed
13 Breaking time
14 Heating
Wash cycle
PW 6101
PW 6131
PW 6161
PW 6201
60 dB
61 dB
62 dB
62 dB
Spin cycle
73 dB
72 dB
77 dB
77 dB
* Not valid for this machine.
35
36
Installation Instructions
Help to protect the environment
Disposal of the packing materials
Disposal of an old appliance
The packing materials protect the appliance
during shipping. They have been designed
to be biodegradable and recyclable.
Old appliances may contain materials that
can be recycled. Please contact your local
recycling center about the possibility of
recycling these materials.
To prevent suffocation, ensure that any
plastic wrappings, bags, etc. are disposed
of safely and kept out of the reach of
children.
38
Ensure that the appliance presents no
danger to children while being stored for
disposal. Before discarding an old
appliance, unplug it from the outlet, cut off
its power cord and remove any doors to
prevent hazards.
Installation Instructions
Installation site
The washer must only be installed by a
Miele authorized service technician.
Before installation or service disconnect
the power supply to the work area.
The minimum dimensions and distance
required from the wall, as shown in the
installation diagram, must be observed to
allow service to be performed and the
data plate to be viewed.
A concrete or reinforced floor is the most
suitable surface for the washer. These types
of floors are less prone to vibration during
the spin cycle.
The washer must be leveled for proper
operation. The machine does not need to be
installed on a base, however, any
unevenness in the floor must be
compensated for.
Do not install or store this machine in a room
where temperatures below freezing may
occur or where the machine may be
exposed to the weather.
Do not install the washer on carpeting.
Carpeting will block the washers air vents.
39
Installation Instructions
Removing the shipping struts
Four red-marked shipping struts, two at the
front and two at the rear, are each fixed with
3 hex screws.
^ Take off the front and back panel of the
machine by removing the screws at the
bottom edge of the front service panel and
the screws in the rear panel and remove.
^ Remove the shipping struts at the installation
location before using the washer.
Save the shipping struts for future use. They
must be refitted if the machine is moved.
Do not move the machine without all of
the outer panels in place.
40
Installation Instructions
Plumbing
The machine should be connected to two
water supply valves, which conform with
local and national regulations. Installation
must be carried out by an authorized
service technician.
Connecting the water intake / water
drain hoses
See the enclosed installation plan.
A water pressure flow rate of at least 14.5 psi,
maximum 145 psi is required.
The inlet pressure hoses supplied with the
machine must be used for connection to the
water supply.
The hoses should only be replaced with
genuine Miele spare parts which fulfill the
pressure requirements.
The hot water intake must not exceed a
temperature of 158°F (70°C).
Cold water connection only
See the enclosed installation diagram.
To ensure the machine is correctly
connected please follow the installation plan
and the separate installation instructions
supplied with the machine.
,Must comply with all local codes.
41
Installation Instructions
Electrical connection
Steam connection
All electrical work must be performed by a
qualified service technician in accordance
with applicable codes and standards.
The steam connection must only be
connected by a certified installer. For more
information see the enclosed installation
plan and the installation manual.
The connecting terminal is located behind a
cover.
The machine must only be connected to the
voltage and frequency shown on the data
plate.
Connecting the dispensing pumps
The machine is equipped with a multi-tap
transformer.
The connecting terminal for 4 time controlled
dispensing pumps is located behind the
cover next to the electrical connection.
Steam heated washers are factory set to
3 phase, 208 V, 60 Hz
The dispensing pumps can be operated
without the multifunction module.
They can be converted to
3 phase, 240 V, 60 Hz by a Miele Service
Technician.
Electrically heated washers are factory set
to 3 phase, 230 V, 50/60 Hz
They can be converted to
3 phase, 208 V, 60 Hz by a Miele Service
Technician.
To activate the heating the water level in the
drum must be 2" (50 mm) high.
A motor overload protection is located in the
motor winding.
See the enclosed wiring and installation
diagrams.
42
Quick Guide
1. Sort the laundry
Only use this machine for items that are machine washable, see item fabric care label.
^ Empty all pockets.
2. Turn the machine on and load the laundry
^ Press the I "On" button to turn the machine on.
^ Open the drum door and load the laundry.
^ Close the drum door.
3. Add detergent
^ Add detergent:
Main wash in detergent container j,
Prewash in detergent container i,
Fabric softener/ starch in front detergent container p,
Additional liquid aids in rear detergent container p (if programmed).
4. Select a program by turning the jog shuttle
Programs may vary depending on the offerings of your machine.
Standard programs
1
2
3
4
5
6
7
8
Hot Wash 194°F
Cottons 140°F
Cottons Intensive 140°F
Cottons 86°F
Cottons Intensive 86°F
Wrinkle Free 140°F
Wrinkle Free Intensive 140°F
Wrinkle Free 86°F
9
10
11
12
13
14
15
16
Wrinkle Free Intensive 86°F
Delicates
Woolens 86°F
Handwash Woolens 86°F
Extra Starch
Extra Rinse + Spin
Extra Spin
Extra Drain
5. Press h "Start".
The selected program begins.
6. At the end of a program
The program end is displayed.
^ Open the door by pulling the handle.
Remove the laundry.
^ Leave the drum door open.
^ Turn the machine off with the 0 "Off" button.
1
Hot Wash
Program end
Door can be opened.
m
FC
A
43
All rights reserved / 2106
06 578 520 / 03
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement