null  null
Installation
Instructions
COMMERCIAL SHOWER
SYSTEM KITS: 1.5gpm & 2.5gpm
1662SG.214
1662SG.224
16 6 2 S G . 2 14 ( 1. 5 g p m )
16 6 2 S G . 2 2 4 ( 2 . 5 g p m )
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
Installation must conform to all local building codes.
Recommended Tools & Materials
M965669 (3/15)
Sealing Tape
10'
Pencil
Phillips Screwdriver
Torch
Hammer
Tape
Measure
6mm (15/64")
Drill Bit
Electric Drill
Adjustable Wrench
Pipe Wrench
Tubing Cutter
ROUGHING-IN DIMENSIONS
1-5/8" TO 3-1/4"
1/2" NPT
FINISHED WALL
1660766.002
(1.5 gpm)
8-1/8"
2-5/16"
1660767.002
(2.5 gpm)
4" REF.
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65" TO 78"
OPTIONAL
3-1/8" DIA.
1/2" NPSM
8"
7" REF.
1/2" NPT
FINISHED
WALL
74" FOR HEAD
CLEARANCE
1/2"
1-1/4"
12"
OPTIONAL
3-1/8" DIA.
1/2" NPT
2-3/4" DIA.
36"
45˚
3-1/8" DIA.
5-3/4"
12"
OPTIONAL
6" DIA.
1-5/8"
37-1/2"
18"
OPTIONAL
PLUG TUB
OUTLET
1/2" COPPER
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN
60"
36" TO
48"
1" MIN.
5-1/8" REF.
1/2" SUPPLIES
VALVE BODY HAS 1/2"
SWEAT INLETS AND OUTLETS
TOP OF TUB RIM
BOTTOM OF TUB
4"
1
INSTALL THE R120SS VALVE BODY
R120SS
NOTE
REFER TO INSTALLATION INSTRUCTIONS (M968387) SUPPLIED WITH VALVE BODY FOR
COMPLETE INSTALLATION AND REPAIR PART INFORMATION.
IMPORTANT
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS
(IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops
(if present) and plaster guard to continue installation. Use thread sealant or Teflon tape
on threaded connections.
See Roughing-in diagram before starting.
Connections are:
1/2" copper sweat for sweat inlets
1/2" copper sweat for sweat tub and shower outlets
2
1/2" SWEAT PLUG
INSTALL THE R430 THREE-WAY DIVERTER
THREE-WAY
DIVERTER
NOTE
REFER TO INSTALLATION INSTRUCTIONS (50321) SUPPLIED WITH DIVERTER FOR
COMPLETE INSTALLATION AND REPAIR PART INFORMATION.
IMPORTANT
The reverse side of the body is marked with arrows.
CAUTION: Do not solder near the VALVE. Damage to the SEAL may occur. Do not seal
any outlets. The DIVERTER cannot be used as a stop valve. Use thread sealant or sealing
tape on threaded connections.
1/2" NPT
SHOWER
See Roughing-in diagram before starting. The port with the BATH TUB picture is the high flow.
The DIVERTER can be installed with the inlet rotated in any position.
1/2" NPT HAND
SHOWER
All connections are 1/2" NPT.
1/2" NPT TUB
For proper positioning the finished wall must be within the side of PLASTER GUARD.
Connect the R430 THREE-WAY DIVERTER to the R120SS VALVE BODY.
1/2" NPT INLET
3
MAKE ALL CONCEALED PIPING CONNECTIONS
See Roughing-in diagram before starting.
Make Hot and Cold supply connections to the VALVE BODY. Inlet and outlet connections to the valve body are 1/2" copper sweat.
Make Tub Filler connection from DIVERTER. (Use the port with the BATH TUB picture). DIVERTER IS 1/2" NPT. TUB SPOUT
connection is 1/2" copper for SLIP-ON SPOUT.
Make the connections for the SHOWER and HAND SHOWER. The SHOWER and HAND SHOWER connections are 1/2" NPT.
For support, use PIPE BRACES secured to wooden braces. Cap off SHOWER, HAND SHOWER and TUB SPOUT FILLER PIPE.
With the R120SS VALVE turned off, turn on water supplies. Check for leaks.
Finish all wall construction.
4
INSTALL VALVE TRIM
FLOWISE
SHOWER HEAD
NOTE
REFER TO INSTALLATION INSTRUCTIONS (M968763) SUPPLIED WITH VALVE
TRIM KIT FOR COMPLETE INSTALLATION AND REPAIR PART INFORMATION.
PLUG
When finished tiling the wall, remove PLASTER GUARD.
Remove cap from tub supply and plug from shower pipe.
PLASTER GUARD
CAP
M965669 (3/15)
5
INSTALL DIVERTER TRIM AND HANDLE
When finished tiling the wall, remove PLASTER GUARD.
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Thread ESCUTCHEON HOLDER (2) onto DIVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against finished wall.
2
Install HANDLE SKIRT (4) onto VALVE STEM (5).
Push DECORATIVE RING (6) onto LEVER HANDLE (7).
Align LEVER HANDLE (7) and push onto
HANDLE SKIRT (4). Install HANDLE
SCREW (8) and tighten.
4
3
6
Push INDEX CAP (9) into LEVER
HANDLE (7).
9
1
MAX
5
8
PLASTER GUARD
7
6
INSTALL WALL SUPPLY
Supply to WALL SUPPLY is 1/2" NPT. See rough-in above for detailed information.
1/2" NPT
APPLY SEALANT
OR SEALING TAPE
Apply sealant or sealing tape to threads of 1/2" NPT supply nipple.
7
INSTALL HOSE AND HAND SHOWER
TEST SHOWER SYSTEM
Install SEAL (1) into COUPLING NUT (2). Connect COUPLING NUT (2)
to WALL SUPPLY NIPPLE (3) and tighten.
INSTALL second SEAL (4) into SPRAY HOSE END (5) and connect
HAND SHOWER (6) to SPRAY HOSE END (5). Hand tighten.
6
Turn on water supplies and check all fuctions of of the SHOWER
SYSTEM KIT. Check for any leaks.
4
5
3
1
2
M965669 (3/15)
8
INSTALLATION INSTRUCTIONS
The GRAB BAR (1) works best when secured to the wall studs or cross brace using WOOD SCREWS. If mounting
into the studs is not possible, use appropriate wall fasteners provided to secure the installation.
Mark a vertical center line in the location you wish to install the SLIDE BAR (1). NOTE: The height from the finished floor
is optional. See rough-in drawing for suggested dimensions.
Determine desired height from the finished floor to the lower support and mark a horizontal center line. Slide the two
WALL ESCUTCHEONS (5) away from the MOUNTING FLANGES (3). Position the GRAB BAR (1) as shown in Fig. A and
mark the location of the six mounting holes to be drilled. Fig. A. Using a #10 masonry drill, drill six mounting holes
1-1/4" max. deep. Fig. B.
Install the six ANCHORS (2) provided into the mounting holes. Use a hammer to lightly tap ANCHORS (2) into place.
Make sure they are installed flush against the finished wall. Fig. B.
Align and place the GRAB BAR MOUNTING FLANGES (3) over the installed ANCHORS (2). Secure the GRAB BAR (1)
to the wall with the SCREWS (4) provided. Fig. B.
Push WALL ESCUTCHEONS (5) against finished wall. Rotate WALL ESCUTCHEONS (5) clockwise to lock into
position. Fig. C.
Make sure larger diameter side of SPRAY HOLDER (6) is facing upward. If not rotate SPRAY HOLDER (6) 180 dergees.
Rotate the LEVER HANDLE (7) to the unlocked position. Push the SPRAY HOLDER (6) side onto the GRAB BAR (1).
Push the LEVER HANDLE SIDE (7) over the SPRAY HOLDER ARMS (8) until the two snap togerther.
Check operation of SLIDE BAR (1) by rotating HOLDER LEVER (7) and moving HAND SHOWER HOLDER (9) up and down.
Rotate LEVER HANDLE (7) back to lock HAND SHOWER HOLDER (6). Fig. B.
Fig. A
Fig. B
C/L
4
2
3
Fig. C
DRILLED
MOUNTING
HOLES
ROTATE
CLOCKWISE
TO LOCK
VERTICAL
CENTER LINE
914mm
(36")
5
5
1
LARGE
DIAMETER UP
1
1
6
UNLOCK
7
8
LEVEL
LOCK
5
FINISHED
FLOOR
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN
915mm TO 1525mm
(36")
(60")
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
M965668 (3/15)
COLONY SOFT
SHOWER TRIM
PRESSURE BALANCE
TEMPERATURE/VOLUME
CONTROL VALVE
MODEL NUMBER
T675.501
023560-0020A
SHOWER ARM
AND FLANGE
MODEL NUMBER
R120SS
051122-0070A
SCREWDRIVER STOPS
013205-0070A
STOP VALVE O-RING
TUB SPOUT
MODEL NUMBER
1660.710-002
FloWise™
SHOWER HEAD
8888.056
M953530-0020A
SHOWER HEAD
M952100-0070A
PRESSURE BALANCING UNI
M961856-0020A
ESCUTCHEON AND SCREWS
023529-0070A
CARTRIDG
078016-0020A
ESCUTCHEON SCREWS
050145-0070A
1/2" SWEAT PLUG
M907050-0020A
ESCUTCHEON CAP SET
M961854-0070A
FIXATION RING WITH SCREWS
023603-0070A
CARTRIDGE SCREWS
8888.056-0020A
SPOUT (Slip-on)
M909606-0020A
DECAL
030126-0070A
HANDLE SCREW KIT
Appropriate finish code
CHROME
002
M961636-0020A
LEVER HANDLE KIT
060220-0070A
DIVERTER REPAIR KIT
3-WAY DIVERTER
VALVE
Appropriate finish code
CHROME
002
MODEL NUMBER
R430
051310-0070A
SPRING KIT
912737-0070A
STEM O-RING
051309-0070A
CAP
PLASTER
GUARD
THREE WAY
BODY
060219-0070A
STEM KIT
012157-0020A
HANDLE SKIRT
012288-0020A
ESCUTCHEON KIT
MAX
912647-0070A
CAP SEAL
012189-0020A
INDEX BUTTON
012673-0020A
LEVER HANDLE
HERITAGE HANDLE
DIVERTER TRIM
MODEL NUMBER
954027-002OA
ESCUTCHEON HOLDER
T342.430
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2015
012205-0070A
COLOR RING KIT
918572-0070A
HANDLE SCREW
M965669 (3/15)
3-FUNCTION HAND
SHOWER
1660766.002
(1.5 gpm)
1660767.002
36" SLIDE BAR
1660.236.002
(2.5 gpm)
WALL SUPPLY
M9641800020A
SPRAY HOLDER
ASSEMBLY
8888.037.002
M964179-0070A
MOUNTING KIT
8888037.002
WALL SUPPLY
M962520-0020A
CHECK VALVE
METAL HOSE
030782-0020A
HOSE KIT
8888.035.002
Appropriate finish code
CHROME
002
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2015
M965669 (3/15)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement